7/28/2019 BOQ for Civil-Bhatinda
1/19
Item
No.D E S C R I P T I O N Unit Quantity
CIVIL1 Excavation up to 1.5 m depth M3 7670
Excavation in all types of soil viz. sand, clay, soft & hard murum etc.
(excluding soft/hard rock) for footings, steps, plinth beams, equipment
foundations, drains, trenches, manholes, underground tanks, etc
including shoring, strutting, dewatering wherever required (until foundation work
is complete). Item also includes carting, stacking if required by MMCI / HPCL ,
Engineer In Charge ,spreading, levelling and compacting/ consolidating surplus
materials with any lead within HPCL's premises or as per instruction of
MMCI / HPCL Engineer In Charge (Rate includes removal of any vegetation,
small shrubs etc.)
2 Excavation from 1.5m to 3.0 m depth M3 210
Same as item 1 above but for 1.5 m to 3.0 m depth
3 Filling with excavated earth M3 5210
Filling the sides of foundations, sub-structures etc. with approved quality
of earth laid in layers not exceeding 300 mm in loose thickness including
levelling, watering, ramming, rolling, compacting with 10-12MT mechanical roller /
hand compactor/mechanical rammer to 95% Modified Proctor Density etc.
complete with any lead within HPCL's premises as directed and instructed by
MMCI/HPCL Engineer Incharge. (Note: Item doesnot include excavation)
4 Filling with imported murum M3 4915
Supplying and filling murum below grade slab / within plinth of approved quality with
PI of 1 to 7(Low plastic) containing not more than 20% cohesive fines namely clay
and Max. dry density of material not less than 1.80 gms/cc, including
identifying & locating of borrow pits, excavation at borrow pits outside Plant
premises; payment of Royalty to Owner of borrow pit, if applicable; payment of
applicable royalties, taxes, etc to Statutory Authority for operating the borrow pit;
loading at borrow pit end; transportation from borrow pit to HPCL Premises;
removing debris, organic matter, etc; spreading in layers not exceeding
300mm loose depth; dewatering during course of filling, watering, compacting to
obtain 95% of modified proctor maximum laboratory dry density all complete as
per specifications and instructions of MMCI/HPCL Engineer-in-Charge.
5 Disposal of surplus excavated earth M3 2670
Disposal/carting away surplus excavated earth / debris etc. outside HPCL's
LPG Plant premises to unobjectionable place identified by vendor.
6 Sand Filling M3 150
Supplying and fil ling locally available good quality river sand in trenches, pits etc in
layers of 150 mm thick including watering and compacting to achive 95 % Modified
Proctor Density etc all complete as per instructions of MMCI/HPCL Engineer-in-
Charge.
7 PCC (1:3:6): M3 100
Supplying and laying Plain Cement Concrete of nominal volumetric mix 1:3:6(1 Cement:
3 Sand: 6 Crushed stone aggregates) with 40mm and down size graded aggregates
below RCC foundations any other work as per requirement including any required
permanent brick masonry, shuttering, dewatering, tamping, ramming, curing, etc allcomplete as per instructions of MMCI/HPCL Engineer-in-Charge
8 PCC M15 M3 800
Supplying and laying Plain Cement Concrete of nominal volumetric mix 1:2:4(1 Cement:
2Sand:4 Crushed stone aggregates) with 20mm and down size graded aggregates
below plinth protection & any other work as per requirement including any required
permanent brick masonry, shuttering, dewatering, tamping, ramming, curing, etc all
complete as per instructions of MMCI/HPCL Engineer-in-Charge
42
7/28/2019 BOQ for Civil-Bhatinda
2/19
Item
No.D E S C R I P T I O N Unit Quantity
9 PCC ( 1:4:8) M3 325
Supplying and laying Plain Cement Concrete of nominal volumetric mix 1:4:8(1 Cement:
4 Sand: 8 Crushed stone aggregates) with 40mm and down size graded aggregates
below RCC foundations any other work as per requirement including any required
permanent brick masonry, shuttering, dewatering, tamping, ramming, curing, etc all
complete as per instructions of MMCI/HPCL Engineer-in-Charge
10 RCC M25 upto Plinth level M3 2690
Supplying & laying in position Controlled grade Reinforced cement Concrete for
footings, foundations, rafts, pedestals, columns, beams, walls,
staircases, trenches, manhole pit, equipment foundations, grade slabs
(including expansion, construction, control, isolation joints etc), kerbstones
encasing of pipes etc at depth below and upto plinth level. with design mix of
required grade at all locations and levels using 20mm size and down graded
aggregates in all types of works [including leaving pockets, placing of conduits,
making openings, pockets placing inserts/ sleeves in columns/ beams/ slabs
etc.] machine mixing, lifting, placing, machine vibrating, tamping, curing etc. as
specified, complete without Reinforcement as per drawings & / or as directed by MMCI
/ HPCL Engineer Incharge.
NOTE: 1) The rate also includes cost of Supplying offsets, cutouts,good quality
plywood shuttering,props, construction joints, making holes in or cutting formwork for
taking out dowel bars, hacking the exposed surfaces to receive plaster as
necessary.
NOTE: 2) To get required workability or for any other reason whatsoever if
additives, plasticizers etc. are to be added the cost of procuring and adding
the same shall be included in the cost of concrete unless specified otherwise.
NOTE: 3) All testing of concrete quality as per relevant IS shall be under the scope.
11 RCC Grade M20 M3 380
Same as Item no 10 but for M20 Grade concrete in grade slab,paving etc.
12 RCC Grade M25 above Plinth M3 1475
Same as Item no 10 but Concrete for RCC works at all levels above plinth level for
all structures, columns, beams, floor slabs, roof slabs,
sunshades , lintels, staircases, fins, chajjas, pardis, sills, copings, projections,column/ beam encasings etc.(up to a ht.of 12 mts.) from plinth level.
13 MS Round Bars MT 1
Supplying, laying & fixing in position MS reinforcement of Fe 250 conforming to IS
432- part 1 for hold fast, locations & levels including cutting, bending & welding to
insert plate etc. complete as specified and directed by Engineer/HPCL Engineer
Incharge.
14 CRS bars for Reinforcement MT 440
Supplying ,cutting,bending and placing in position HYSD TMT Bars conforming to IS:
1786 Fe415 or Fe 500 , for foundation raft, beams, slab, columns, etc. including
transporting the steel, straightening, cleaning, decoiling, to required shapes and lengths,
binding with Contractors own 16 gauge SWG binding wire at every intersection ,
supplying and placing with proper cover blocks, supports, chairs, overlaps, spacers, etcall complete as per specifications and bar bending schedule approved by MMCI/HPCL
Engineer-In-Charge.
42
7/28/2019 BOQ for Civil-Bhatinda
3/19
Item
No.D E S C R I P T I O N Unit Quantity
15 Anchor / Foundation Bolts MT 8.5
Supplying, fabricating and fixing in position M.S. round holding down (foundation) bolts
with nuts and check nuts, washers, pipe, plates, etc., all complete as per instructions of
MMCI/HPCL Engineer-in-Charge
NOTES:
1. The rate to include cost of bolt and also to include Supplying and welding holding
arrangements such as plate or angle at bottom.
The rate also to include preparing and fixing template for keeping the bolts at correct
centres before, doing and after concreting.
16 Providing pockets -300mm deep Nos 10
Forming pockets for anchor bolts, etc in concrete, including supplying & fixing
necessary templates supports and setting out, including protecting the pockets from
filling up, plan area not exceeding. Depth upto 300mm
17 Providing pockets >300mm deep Nos 10
Same as above but depth >300mm to 700mm
18 Precast RCC for ornamental work
Providing, hoisting and fixing precast reinforced cement concrete in slabs/
bresummers /mouldings/vertical & horizontal fins/forming box louvers band, facias,
eaves board etc. including setting in cement mortar 1:3 (1 cement: 3 corase sand),
cost of required centering, shuttering and finishing smooth with 6 mm thick cement
plaster 1:3 (1 cement: 3 fine sand) on exposed surfaces but excluding the cost of
reinforcement with 1:11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate
20 mm nominal size) for Mughapu for Gate cabin etc. and castings over gate entry and
any other ornamental work required and as directed by the Site-in-charge.
M3 10
19 Cast-in-situ RCC for ornamental work
Providing, hoisting, casting reinforced cement concrete in slabs/ bresummers
/mouldings/vertical & horizontal fins/forming box louvers, band, facias, eaves board etc.
including setting in cement mortar 1:3 (1 cement: 3 corase sand), cost of required
centering, shuttering and finishing smooth with 6 mm thick cement plaster 1:3 (1
cement: 3 fine sand) on exposed surfaces but excluding the cost of reinforcement with
1:11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate 20 mm nominal size)
for Mughapu for Gate cabin etc. and castings over gate entry and any other ornamental
work required and as directed by the Site-in-charge.
M3 50
20 Insert Plates / Nosing angles / Channels MT 16
Supplying, fabricating and fixing in position at required locations to correct lines and
levels, angles, inserts for pits in shed & stairs , cable trenches and all types of
RCC, PCC & masonry incl. necessary holdfasts , welding, machining, grinding,
threading etc.Exposed surface will be thorughly cleaned & painted with epoxy
primer & paint. (All materials & accessories required shall be provided by
Contractor).
21 Non Shrink Grout M3 2
Supplying and laying under equipment, grouting pockets etc GROUT made from
Non Shrink Compound ( all as per manufacturer's specification & approved by
MMCI/ HPCL Engineer Incharge. )
22 Ordinary Grout M3 7
Grouting below column bases including anchor bolt pockets / pipe sleeves, etc. with
cement grout of 1:2 mix ( 1 cement :2 sand ) including supply of all materials, labour,
tools, plant shuttering, strutting, curing, with all leads and lifts, etc., all complete as per
instructions of MMCI/HPCL Engineer-in-Charge
23 UPVC Rainwater pipes RM 875
Providing, laying and fixing in position on surface with necessary MS Clamps
and wooden blocks of approved quality U-PVC 110 dia rain water pipes of Class I
to IS 4985 wherever required specials including lead caucking joints, testing
and painting the pipes wherever required with 3 coats of approved oil paint in
approved colours. (Specials shall include all bends, offsets, shoes, junction
etc. Rate shall be inclusive of such specials measured on linear basis.)
24 Epoxy Bonding Agent M2 2
Supplying & applying epoxy bonding agent between old concrete to new
concrete inclding preparation of surface at levels complete as per manufacturer's
specification & as directed & instructed by MMCI/ HPCL Engineer Incharge.
25 Anti-termite treatment M2 2100
42
7/28/2019 BOQ for Civil-Bhatinda
4/19
Item
No.D E S C R I P T I O N Unit Quantity
Supplying anti-termite treatment using CHLOROPYRIPHOS 20% EC (ISI marked) in
1% concentration as per IS 6313 of 1981 by creating a chemical barrier under and
around the wall, footings, plinth & foundations junction of wall & floor along the
external perimeter of building, conduits etc as per IS 6313 all complete as per
instructions of MMCI/HPCL Engineer-in-Charge
(Mode of measurement shall be plinth area only).
26 Structural Steel Work MT 520
Supplying raw steel as per IS:2062, fabricating, welding and/or bolting, as required,
erecting and fixing in position all types of structural steel work viz rafters, trusses,
purlins, beams columns,plates sag rods, shop/site fabricated including all accessories
viz. nuts, bolts, cleats, gussets, etc as per specification complete as directed by
MMCI/HPCL Engineer in charge. The rate to include for welding weights, site
connection, nut & bolts and same will not be measured for payment .
42
7/28/2019 BOQ for Civil-Bhatinda
5/19
Item
No.D E S C R I P T I O N Unit Quantity
Supply of all consummables shall be under contractor'scope.
27 Chequered plate MT 8
Same as item no.26 but for 6 O/P chequered plate fixed over trench or other
pit covers including supply of plates & consummables.
28 Grating M2 200
Same as item no. 26 but for gratings of designed size & shape fixed over
walkways,platforms, stairs etc including supply of all materials &
consummables with painting complete as per drg & specification.
29 Tubular Steel Work MT 0.5
Supplying,transporting,fabricating,loading,unloading& erecting in position to the
required line & level,steel work made out of tubes as per IS1161 Gr Yst210 or as
per IS1239 for trusses,bracings,tie runners,pipe supports,towers& cleats,base
plate gussets,grits,purlins,side runners etc.including cutting,welding,bolting ,
threading,preparation for fabrication including painting,staging,scaffolding etc.
as directed by MMCI/ HPCL Engineer incharge.
30 Painting MT 520
Surface preparation by wire brushing free of scales with 2 coats of
zinc rich primer (total DFT-75 microns) & 2 coats of first quality synthetic enamel
paint (total DFT-50 microns) as approved by MMCI / HPCL
engineer in charge
31 Pipe Railing RM 150Supplying, fabricating & erecting pipe handrailing made out of M.S. "C" class pipes
(appr. 1050mm high) with 32NB dia. pipe hand rail, 2-20mm NB dia pipe knee rails
and 100 x 5mm thk. toe plate with 32NB pipe vertical support spaced at
approx.1500 c/c and at corners & change of direction. Also including assembly for
fixing to inserts or stringer beams complete in all respects including surface
preparation for painting and 2 coats of red oxide zinc chromate primer & two coats
of 1st quality synthetic enamel paint of approved make & shade all as directed &
instructed by MMCI / HPCL Engineer incharge NOTE:
Items shall be measured as total length of completed pipe railing. (not individual
pipe lengths)All sections shall be of IS:2062.
Supply of all consummables shall be under contractor'scope.
32 230 thk Brick Masonry in CM 1:5 M3 1310
Supplying & constructing 230 thk brick masonary walls using bricks of first class burnt
clay (class 3.5 as per IS:12894, Compressive strength of Brick 35 kg/cm2) ofapproved source at all locations and levels including scaffolding, racking of joints,
watering but excluding cement plaster finish with cement mortar(1:5)complete
as directed and instructed by MMCI / HPCL Engineer incharge.(up to a lift of 12 mts.).
33 110 thk half Brick Masonary(1:4) M2 500
Supplying and constructing 110mm thickburnt clay brick masonry in super structure
using first quality bricks (class3.5 as per IS:12894, Compressive strength of
Brick 35 kg/cm2) of approved source in cement mortar (1:4) including necessary
scaffolding, racking of joints, watering but excluding cement plaster finish complete
as directed and instructed by MMCI / HPCL Engineer incharge.(up to a lift of 12 of
mts.) Transoms & mullions shall be provided in the brick work when length or
height of wall exceeds 2M. Transoms shall be provided at lintel/door height.
Spacing of mullions shall not exceed 1.5M c/c. Size of transoms/mullions shall be
115mm x 115mm with M15 grade concrete & 10mm down graded aggregate only.Supplying and placing formwork etc for transoms/mullions etc shall be included in
the quoted rate.
34 12 mm thick Plaster M2 3900
42
7/28/2019 BOQ for Civil-Bhatinda
6/19
Item
No.D E S C R I P T I O N Unit Quantity
Supplying & doing 12mm thick cement plaster in C.M. 1:4 mix finished with neeru.as
per specification to all RCC & masonry work at all levels and locations including
grooves, pattas, drip moulding, scaffolding, watering, hacking out joints in masonry or
concrete work as per specification. The rate to include Supplying and fixing of 200mm
wide chicken wire mesh of 26G & 15mm mesh size with minimum overlap of 150 mm at
the junction of different construction materials all complete as per instructions of
MMCI/HPCL Engineer-in-Charge
35 6 mm thick Plaster M2 2050
Supplying and applying max. 6 mm thick cement plaster in C.M. (1:3), finished with
Cement slurry to ceilings or elsewhere as directed; including pattas grooves in all
positions, including necessary scaffoldings, curing, with all lifts and leads, rubbing with
small trowel etc. all complete as per instructions of MMCI/HPCL Engineer-in-Charge
36 12 mm thick Plaster & 8 mm thick plaster ( combined 20 mm) M2 5000
Supplying and doing sand faced plaster 20mm thk in C.M. 1:5 & 1:2 in 2 coats of 12
mm & 8 mm respectively to all RCC and masonry works at all locations and levels
including required grain finishing, curing etc. complete as per specification and as
directed and instructed by MMCI/HPCL Engineer in charge.
NOTE: Rate to include the cost of the base coat of not less than 12 mm thickness,
external coat 8 mm thk. hacking, scaffolding, grooves, patta, drip moulds, curing and
Supplying and fixing 150mm wide G.I. chicken mesh 26g thk & 15mm mesh size with
minimum overlap of 150 mm at junctions of brick and RCC/PCC work etc. as well as
Supplying and mixing waterproofing compound of approved make in both coats as per
manufacturers specifications all complete as per instructions of MMCI/HPCL Engineer
37 20 mm thick Waterproofing Plaster M2 15
Same as item no 34 above but for 20 mm/ 12mm thick back up plaster for internal surface
of RCC/Masonry work which is to be tiled.
38 Rubble Soling M2 7525
Supplying and doing 230 mm thick dry rubble stone packing/soling under
floor, foundation, pavement, roads,steps,ramps & other similar locations,
handset vertically in rectangular lines, interstices filled in with smaller stone
chips including watering, compacting/consolidating & finishing to the required
levels and lines etc with the use of 10 Ton roller and with mechanical rammers
complete as directed. (Blinding layer shall be of metal, sand or murrum.)39 Cudappah Stone Flooring 30mm thick M2 50
Supplying & laying in floor approved quality machine cut, machine polished cudappah
stones of specified size and thickness in green or grey or approved tint in pattern or
layouts as per drawing over a bed of 20mm C.M.1:4 including curing & polishing
smooth as per specifications & as directed & instructed by MMCI / HPCL Engineer
Incharge)
40 Cudappah Stone Skirting RM 35
Same as item no 39 above but for 30mm thk polished cudappah stone in
treads , riser , landings & skirting.
41 Marble Tiles in floors M2 25
Supplying & fixing 1st class quality Marble tiles of approved make & colour & size as
directed with thickness 25mm including corners and curves laid with white cement
under bed of 25 mm cement mortar 1:3 including curing, machining,polishing smoothin floor as per drawing, specification & as per instruction of MMCI / HPCL Engineer
Incharge.
42 Marble Tiles In skirting RM 18
same as item no 41 above but in skirting
43 18 mm thk. Granite slabs in floors M2 125
Providing & fixing 18mm thick mirror polished, machine cut black granite slab of size
1.0 to 2.0 sqm for kitchen platforms, vanity counter facias, floors and similar
locations laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand)
with joints treated with white cement, mixed with matching pigment, epoxy touch
ups, including rubbing, curing etc. complete at all levels.
44 Granite slab in skirting RM 200
Same as item 43 above bu in skirting
45 Edge moulding for granite slab RM 400Providing edge moulding to 18mm thick granite stone for counters, vanities etc. over
item above including machine polishing to edge to give high gloss finish etc. complete
as per design approved by Engineer-in-charge.
46 Eurocon Cement Tiles M2 800
Supplying & fixing cement tiles of approved make & red colour laid over bedding of
cement mortar (1:3) of appropriate thickness in approved design & pattern over sloped
42
7/28/2019 BOQ for Civil-Bhatinda
7/19
Item
No.D E S C R I P T I O N Unit Quantity
or flat roof ,in porches, in walkways( as per detailed architectural drawings all as directed by
MMCI/HPCL Engineer Incharge.)
47 Glazed MP tiles M2 550
Supplying and laying of glazed Mangalore Pattern (MP) first quality tiles of 400 mm or
nearest size over the cement mortar reaper bands (already provided) to connect lines
and levels at all heights as directed by the Site-in-charge.
48 Glazed MP hip and ridge tiles RM 140
Supplying and laying first class glazed MP hip and ridge tiles set in cement mortar 1:3
including finishing edges neat, etc. complete as directed by the engineer-in- charge
49 Vitrified Tiles For Flooring M2 800
Supplying and laying in position polished 1st quality vitrified tile ( 600mm x 600mm
x 10mm thk.) of approved make for FLOORING laid laid over bedding of cement
mortar 1:3 (of appropriate thickness) in approved design and pattern and (NOTE :
The vitrified tile flooring shall be laid in pattern (as per detailed Architectural drawing
or as directed by MMCI/HPCL Engineer Incharge.)
50 Skirting RM 560
Same as item no 49 but for skirting
51 Ceramic Tiles for Flooring M2 220
Supplying & fixing 1st quality ceramic tiles of approved make & colour & size as
directed thickness 7mm incl. corners and curves laid on C.M. 1:4 bedding of
required thickness with neat cement float and filling joint with white/ coloured
cement in flooring all as directed and instructed by MMCI / HPCL Engineer
Incharge.
52 Skirting RM 160
Same as item no 51 but for skirting
53 Ceramic Tiles for Dado M2 25
Same as Item No. 51 above but in dado/skirting to
give surface flush with plastered/painted surface.
54 Damp proof course M2 108
Supplying & laying damp proof course 40mm thick in P.C.C. 1:2:4 using 12mm
42
7/28/2019 BOQ for Civil-Bhatinda
8/19
Item
No.D E S C R I P T I O N Unit Quantity
size & down grade aggregate mixed with "Cico" or other equivalent
waterproofing compound 3% by weight of cement or as per manufacturers
specifications finished rough including cleaning, curing etc complete as
specified and as directed by MMCI / HPCL Engineer Incharge.
55 Wateproofing for roof / chajja / canopy / RCC Gutters (Polyurethane type) M2 1870
Supplying and applying Polyurethane treatment to roof slab / Chajja /
canopy / RCC Gutters etc as per the manufacturers specifications etc
complete including cleaning, washing, and curing as specified etc complete with
10 years waterproofing guarantee. Note : The mode of measurements for this item
will be the length and breadth of the actual treated surface (i.e. the plan area),
including vata, measured after treatment. No extra will be paid for the vata.
56 Wateproofing for toilet sunk M2 150
Supplying & laying cement based surface water proofing by approved agency for
toilet sunk portion with brickbat coba avg.115mm thk finished at top water proof
scratch coat surface to receive tiling/ floor finishes etc. complete in all respects as
per the specifications with 10 years written guarantee of performance in approved
format all at directed & instructed by MMCI / HPCL Engineer Incharge. NOTE:
(Payment shall be made on measurement of finished plan area only).
57 Mastic Flooring 20 mm thick M2 5690
Supplying & laying Mastic Flooring 20 mm thick anti static & electricallyconductive Mastic flooring confirming to IS 8374 in LPG sheds connecting
Platforms etc.For the horizontal surfaces i.e. floors. Rate to include testing of
one sample at VJTI, Mumbai & submission of report to HPCL
58 Mastic Coating 20 mm on columns/RCC/brickwalls above floor M2 680
Same as item no 57 but for vertical surfaces i.e. columns up to 1.5 m height.
Rate to include Supplying MS chicken wire mesh 20 gauge, required to retain mastic
flooring along vertical surfaces.
59 Ironite Flooring M2 1940
Supplying and laying average 40 mm thick Ironite or approved floor finish in cement
concrete laid in alternate bays in two layers. Bottom layer shall be average 88 mm thick
laid to slope in cement concrete 1:1:2 with 10 mm to 6mm graded stone aggregates
finished rough. Top layer shall be 12mm thick metallic floor hardener finish in Ironite orapproved in 1:4( 1 metallic compound to 4 cement ) by weight and this dry mixture shall
be mixed with stone aggregates 6mm nominal size in ratio 1:2 ( 1 cement mixture and 2
aggregates) by volume including all formwork , 4mm thick glass separator strips, mixing
, compacting , finishing the surface to required line and levels, trowelled smooth and
curing by ponding , etc, all complete as per instructions of MMCI/HPCL Engineer-in-
Charge
60 Plinth Protection M2 2035
Supplying & doing plinth protection around building or pavement including
excavation, rubble soling 230thk ,100 mm thk 1:3:6 grade concrete with broom finish
& as directed and instructed by MMCI / HPCL Engineer In charge (Reinforcement
shall be paid for separately).
61 Aluminium Glazed Doors M2 80
Supplying & fixing powder coated aluminium single leaf or double leaf doors
with frames of size 100mmx45mmx3.18mm thick, double action with shutterframes of vertical style 85mm x 45mm x 2.5mm thick frame, and horizontals
of 100mm x 45mm x 2.5mm with beading clips, EPDM gaskets, night latch,
stopper, glazing with 6mm, clear float glass panes / obscure glass panes of
special selected quality, full handles on both sides of all shutters made of 75mm
x 8mm anodised alumionium plate, stainless steel screws, hinges,
strengthly of hinged styles of approved hardware etc. complete. & as
directed by MMCI / HPCL incharge
62 Partly glazed aluminium doors M2 35
Same as item no.61 but for Partly glazed and Partly aluminium sandwitch
panel sandwitched with 9 mm thk. marine ply overlaid with 18 guage (1.2 mm)
thick Anodised aluminium sheet on both sides & 5.5 mm float glass glazing.
63 PVC Doors M2 40Supplying & fixing PVC Sintex or equivalent door with shutter consisting of shutter
frame made of extrude plastic section having dimensions of 60x24mm anodized
with multi chambered hollow plastic section of 200x20mm with an average wall
thichness of 1mm jointed with one another by a tongue and groove joints and outer
42
7/28/2019 BOQ for Civil-Bhatinda
9/19
Item
No.D E S C R I P T I O N Unit Quantity
frame of door made of extruded plastic section of 68x60mm or nearest on all sides
including Supplying and fixing all required fiiting such as anodized aluminium butt
hinges , tower bolts handles with screws,MS hold fasts for fixing door frames etc.
complete as per manufacturer's specification.
64 Rolling Shutter M2 55
Supplying & fixing Hand operated with pull & push type with ball bearing Rolling
shutters of 18 gauge G.I., 75 mm wide rolled plates with 12mm lap, concave
corrugation, complete with "one piece" construction, pressed steel 75mm channel
guides, brackets, flat springs, door suspension shafts, locking arrangement,
including G.I. 20 gauge top hood cover and 2.5mm thick bottom plate All fitted &
fixed all complete as per instructions of MMCI/HPCL Engineer-in-Charge.
(Measurement for the payment shall be for the area of shutter size clear).
65 Pressed Steel Hollow Metal Doors M2 55
Supplying and fixing Hollow Metal Pressed steel doors having Two hours of fire rating
with 16 gauge pressed steel frames of size 125mmx45mm and 45mm thick single
leaf shutters of 18 gauge MS sheets with stiffeners made of channel 25mm
wide x3.15mm thick (depth of channel to suit shutter thickness) spaced not
more than 300mm apart, horizontally, including attachments for fixing all hardware,
fastenings, fixtures and hardware as per drawing with minimum of 3 nos jambs and
hinges, external locks, internal push bars (should be openable from inside even when
locked from outside) with 2 coats of synthetic enamel paint on one coat of zinc
chromate primer all complete as per instructions of MMCI/HPCL Engineer-in-Charge.
(Measurement for the payment shall be for the area of shutter size clear)
66 Aluminium sliding window M2 80
Supplying and fixing in position powder coated aluminium sliding windows with 6
mm clear glass upto 3 tracks in extruded sections, outer frame having weep holes
and water drainage section at bottom including PVC weather strips & glazing
channels, nylon glider, rubber bumpers in interlocking sections, locking
arrangement etc. complete as directed by MMCI / HPCL incharge.
- Sliding portion
67 Aluminium sliding window M2 35
Supplying and fixing in position powder coated aluminium sliding windows with 6mm clear glass upto 3 tracks in extruded sections, outer frame having weep holes
and water drainage section at bottom including PVC weather strips & glazing
channels, nylon glider, rubber bumpers in interlocking sections, locking
arrangement etc. complete as directed by MMCI / HPCL incharge.
- Fixed portion
68 M.S. Steel windows & ventilators M2 180
Supplying and fixing in position GI coated. Steel windows and ventilators as per
relevant IS with standard rolled sections including grit blasting at shop , 6 mm thick
plain sheet glass with necessary holdfasts, oxidised brass fixtures/fasteners, putty,
glazing clips, or aluminium beading, peg stay, handle, screws etc. complete as per
drawing and specifications complete as directed by MMCI / HPCL incharge.
69 Oil bound distemper M2 5
Supplying and applying three coats of Oil bound Distemper (bybrush) to plastered surfaces of wall and concrete
work (internal walls & ceilings) including rubbing with sand paper,
including primer and two coats of palti , scaffolding etc. complete as per
and as directed & instructed by MMCI / HPCL Engineer Incharge.
70 External Paint M2 4000
Supplying 1 coat of approved primer and two coats of Acrylic Emulsion paint of Asian
Make ( ACE Paint) or equivalent of approved shade over concrete or plastered
surfaces, incl. scaffolding, preparation of the surfaces as per manufacturers
specification including cleaning of surface,over a coat of cement primer all complete as
per instructions of MMCI/HPCL Engineer-in-Charge
71 Providing 2 mm thk. Putty M2 7500
Providing and applying putty of 2mm thick over plastered surface to prepare the surfaceeven and smooth , etc. complete
72 Internal Painting M2 7500
Supplying & applying at all heights,of required shade of approved make including
preparation of surface for painting ,applying primer & putty of approved make with
two or more coats of approved quality of ready mixed plastic Emulsion paint
over a coat of white cement primer.
42
7/28/2019 BOQ for Civil-Bhatinda
10/19
Item
No.D E S C R I P T I O N Unit Quantity
73 Synthetic enamel painting M2 150
Providing and applying synthetic enamel paint, at all heights, of required shade and
approved make on new work including the preparation of surface for painting, applying
primer & putty, of approved make with two or more coats of approved first quality
synthetic enamel paint as directed. all lift and leads.
74 White washing with lime M2 2000
Providing and applying 3 coats of white wash to brick and concrete surface including
providing necessary scaffolding, surface preparation etc. complete. If additional coats
are required to obtain uniform and smooth finish , the same shall be carried out at no
extra cost.
75 Indian WC Nos 10
Supplying & fixing Indian W.C. pan Orissa pattern 580 x 440 mm size with Box
Rim with P or S trap including flushing cistern,flush valve (Front or Rear entry as
required) 100mm dia. C.I. connector upto soil stack or inspection chamber
making flushing water & vent pipe connections with lead pipe for flushing
connection & C.I. pipe for vent connection encasing of flushing connection in
42
7/28/2019 BOQ for Civil-Bhatinda
11/19
Item
No.D E S C R I P T I O N Unit Quantity
concrete & filling balance portion of W.C. with brick bat concrete etc. complete.
The approved make & colour directed by MMCI / HPCL incharge ( Minimum
sinking of floor to be 45 cms) ( at a distance of 60 cms from door - if sinking is
inclined)
76 European WC Nos 5
Supplying & fixing in position floor mounted European water closet with P
or S trap including flushing cistern & sprout ,flush valve as required - black
commander make. Champion brand seat cover with CP brass hinges rubber
buffers & 100 mm CI connector upto soil stack or Inspection Chamber (as the
case may be) with Supplying & making a hole in wall & making it good and
Supplying & making a flushing connection & vent pipe conection etc.
complete including Supplying all material hhbj fittings etc. for the conneciton.
The approved make & colour directed by MMCI / HPCL incharge
77 Urinal Nos 15
Supplying & fixing in position large flat urinal height 61 cms width 40 cms
including auto flushing system including electrical wiring works , brackets
spreader making a water connection including necessary piping drain
connection including C.P. waste coupling C.P. Brass Bottle Trap with
extention piece-wall flange and connection to a Drain Header etc. complete.
The approved make & colour directed by MMCI / HPCL incharge
Supply and installing sensor controlled auto flushing system for urinal ofAutomat/Jaquar make including wiring , electrical works complete in all respects is also
included in this item
78 Stop Cock Nos 30
Supplying & fixing individual stop cock & connections for Supplying individual
manual flushing arrangement. The approved make & colour directed by MMCI /
HPCL incharge
79 Granite partition Nos 15
Supplying & fixing granite partition 20mm thick
between urinals.(Size 900x600)
80 Wash Basin Nos 24
Supplying & fixing wash basin (Rectangular) including C.I. brackets, C.P.
waste coupling, C.P. bottle trap chain & plug C.P. stop cock at supply endone long body C.P. pillar cock connecting tubing drain connection etc.
complete. The approved make & colour directed by MMCI / HPCL incharge
81 Nahani Traps Nos 24
Supplying and fixing C.I. nahani trap with stainless steel grating
including laying necessary C.I. drainage pipe of minimum
100mm dia upto the external wall everything as per requirements
of local authorities etc. complete in all respects as directed and
instructed by MMCI / HPCL Engineer Incharge.
The approved make & colour directed by MMCI / HPCL incharge
82 Inspection Chamber up to 1.50m Depth Nos 8
Supplying and constructing brick masonry inspection chambers
with 230/345mm brick masonary in cement mortar (1:4) mix, 20mm
thick cement finish plastered internally and externally in cementmortar 1:4 mix incl. necessary excavation, foundation
concrete 1:3:6 mix 150mm thick, top cover with 100mm thick RC slab
in M20 concrete with reinforcement at 100 Kg/M3 of concrete
S.W.G. half round channels 150mm dia, concrete haunches, heavy
duty C.I. manhole cover approx. 450mm dia. and frame 16mm dia. C.I.
rod rungs at 300 mm c/c etc. complete as shown on the drawing
and/or directed and instructed by Engineer/Owner. NOTE: (Brick
work to be 230mm thick upto 1.0M depth and 345mm thick beyond
1.0M depth).
83 Gully Traps Nos 24
Supplying and fixing in position stone ware gully traps 150 x
150mm size with cover including brick masonary chamber of
clear internal size as 300mmx300mm with cement plaster finishes
42
7/28/2019 BOQ for Civil-Bhatinda
12/19
Item
No.D E S C R I P T I O N Unit Quantity
externally & internally all in cement mortar (1:4) mix including C.I.
frame and hinged cover (Heavy duty) etc. everything as per
requirements of local authorities etc. complete in all respects as
directed and instructed by MMCI / HPCL Engineer Incharge.
84 GI Pipes 40 mm dia RM 100
Supplying, laying & jointing G.I. pipes, 'C' class including all fittings and
specials such as bends, unions, elbows, couplings, tees, crosses,
reducers, enlargers, stop-ends, plugs etc. with including Supplying &
making chases in brickwirk/RCC, Supplying & making Anticorrosion
treatment to pipes consisting of a coat of Tar and covering with Bitumen
impregnated hessain cloth - Hydrotesting of pipe to ensure absence of any
leakage & making good of chase in C.M. 1:3 after fixing chicken mesh after
the completion of installation of piping.
85 GI Pipes32 mm dia RM 150
Same as item no 84 but for 25 mm dia pipe
86 GI Pipes25 mm dia RM 15
Same as item no 84 but for 25 mm dia pipe
87 GI Pipes 20 mm dia RM 70
Same as item no 84 but for 20 mm dia pipe
88 GI Pipes 15 mm dia RM 15
Same as item no 84 but for 15 mm dia pipe
89 GI Pipes 12 mm dia RM 110
Same as item no 84 but for 12 mm dia pipe
90 Shower rose Nos 9
Supplying and fixing shower rose & assembly with built in hall joint for instant
direction of changes "R-51 Jetflow" type. Approved make& colour as
directed by MMCI / HPCL Engineer Incharge.
91 Toilet Paper Holder Nos 15
Supplying and fixing in position C.P. toilet paper holder including toilet
paper roll of approved quality and make etc. complete . Approved make
& colour as directed by MMCI / HPCL Engineer Incharge.
92 Glass Mirror Nos 12
Supplying and fixing in position plate glass mirror of size 400mm x 600 mmx 5
mm thick of over 6 mm thick waterproof plywood with wooden moulding at top
and bottom including necessary hardware and synthetic enamel painting
of approved shade to moulding all complete. Approved make & colour as directed
and instructed MMCI / HPCL Engineer Incharge.
93 Soap Dispenser Nos 20
Supplying and fixing in position C.P. Brass liquid soap dispensers
of approved quality and design etc. complete as directed and
instructed by MMCI / HPCL Engineer Incharge.
94 Towel Rods Nos 22
Supplying and fixing in position C.P. M.S. Towel rods 750mm long,20mm dia. with necessary fittings of approved quality and
make etc. complete as directed and instructed by MMCI / HPCL
Engineer Incharge.
95 25 mm dia cast copper alloy stop valve Nos 5
Supplying, providing & fixing 25 mm dia cast copper alloy stop valve , chrome plated
conforming to and tested as per IS:781 of Jaguar make and approved design including
all necessary fittings etc. complete as per Technical specifications mentioned in the
tender document and as directed by the Site-in-charge.
96 20 mm dia stop valve Nos 5
Same as above but for providing 20 mm dia stop valve.
97 15 mm dia stop valve Nos 5
Same as above but for providing 15 mm dia stop valve.98 12 mm dia bib taps Nos 20
Supplying, providing & fixing cast copper alloy screwed down 12 mm dia. Long stem
type bib taps chrome plated conforming to and tested as per IS:781 & of Jaguar make
with all necessary fittings etc. complete as per technical specifications and as directed
by the Site-in-charge.
99 15 mm dia pillar cocks Nos 5
42
7/28/2019 BOQ for Civil-Bhatinda
13/19
Item
No.D E S C R I P T I O N Unit Quantity
Supplying, providing & fixing cast copper alloy screwed down 15 mm dia. chrome
plated Pillar cock conforming to and tested as per IS:781 & of Jaguar make with all
necessary fittings etc. Complete as per technical specifications and as directed by the
Site-in-charge.
100 Ball Cock 12 mm dia Nos 40
Supplying and fixing brass body heavy duty ball cock with PVC
float including necessary fittings & fixtures as instructed & directed by
MMCI / HPCL Engineer Incharge.
101 HDPE Pipe 100mm Dia RM 215
42
7/28/2019 BOQ for Civil-Bhatinda
14/19
Item
No.D E S C R I P T I O N Unit Quantity
Supplying and laying of 100mm dia HDPE pipes of heavy duty & first quality as
approved by MMCI/HPCL Engineer Incharge.Scope include supply & laying of all the
necessary pipe bends,socket/collars required for joining the pipes etc. complete as
directed by MMCI/HPCL Engineer Incharge
102 HDPE Pipe 75mm Dia RM 550
Same as item 101 above but for 75mm dia
103 PVC Pipe 100 mm Dia RM 5
Supplying, delivering and laying PVC pipe (6 kg/cm2 quality) of
approved make for Sewage disposal including bends, offsets, 'Y'-s /
Tees etc., jointing with solvent cement etc all necessary puddle flanges
for joints of PVC and manholes accessories confirming to IS-4985
testing, rectification, filling partly with sand including required excavation
and backfilling the trench etc. everything as per local authorities etc.
complete in all respects as directed and instructed. (Earthwork
excavation and filling the sand will be paid separately under relevant
sections & Items)
104 PVC Pipe 150 mm Dia RM 15
Same as item 103 above but for 150 mm dia
105 Sintex or equivalent water tanks 1000 litre Nos 1
Supplying and erecting ready made storage tanks of 'Sintex' orapproved manufacturer and required size including connecting
necessary supply lines, delivery lines, wash water line and with
manhole cover at top of not less than 450mm clear dia, with locking
arrangement complete as per drawing and as directed and instructed
by MMCI / HPCL Engineer Incharge.
106 Sintex or equivalent water tanks 2000 litre Nos 5
Same as item 105 above but for 2000 litre
107 Sintex or equivalent water tanks 5000 litre Nos 1
Same as item 105 above but for 5000 litre
108 Soak pit Nos 4
Supplying, providing & constructing soak pit of size as per drawing, including excavation& filling the pit with gravel and brick bats of maximum size 80 mm ; the brick masonry
wall shall be as per the details given on the drawing complete as per Technical
specifications mentioned in the tender document and as directed by the Site-in-charge.
109 Precast septic tank -50 users Nos 2
Providing & fixing septic tank suitable for 50 users of Indian Hume Pipe Co. or
construction of septic tank as per drawings / specifications (the rates shall include
excavation, placing in position all necessary connections and accessories, testing the
joints, backfilling etc. complete and as directed.
110 Sink Nos 5
Providing and fixing stainless steel kitchen sink (600 x 450 x 250 mm
deep approx size) of Hindustan Twyford make or any other equivalent
approved make with stopcock, pillar cock, waste couplings, CP bottle
trap, rubber plug and CP brass chain CI brackets, drainage connectionwater supply with drain board and plumbing installations up to external
wall etc complete as directed and instructed by MMCI / HPCL
Engineer incharge
111 Stainless steel hand rail RM 165
Supplying & fixing stainless steel hand railing of grade 304 (16 gauge thick
sections) with glossy finish consisting of 38 NB or nearest size vertical posts 900
heigh at maximum spacing of 1000 c/c with suitable cups at bottom & top rail of
38 NB or nearest size & intermediate rails of 20 NB or nearest size etc complete at
alll levels including bending to required profile. Tungsten inert gas welding & alll
required accessories & labour etc complete.
112 Door Closure Nos 34
Supplying & fixing Godraj make or equivalent confirming to IS : 3564marked aluminium extruded section body tubular type universal hydraulic door
closure with double speed adjustment with necessary accessories & screws
42
7/28/2019 BOQ for Civil-Bhatinda
15/19
Item
No.D E S C R I P T I O N Unit Quantity
etc.complete.
113 Floor spring Nos 15
Providing and fixing double action Everite/Dorma or equivalent floor spring
(Hydraulically operated) as per IS 6315 latest revision for entrance door with all fixturers
and accessories with foundation box, main body and half cover and top cover made of
aluminium alloy pressed dye casting 2mm minimum thick, gun metal piston layer and
cast brass top, center pivot etc. complete including connecting door shutter to hinges,
etc. complete including charges for making good the floors etc.
114 Roof Sheeting M2 12900
Supplying, transporting & stacking , fixing in position Zincalume clip on OR
equivalent sheeting as follow with accessories such as Fasteners & Foam filler
detailed as under all complete as per instructions of MMCI/HPCL Engineer-in-Charge
FASTNERS
Mechanically galvanised self drilling high grip screws 12-14 X55 with integral washers.
EPDM seals and 10-12X25 screws at side laps.( not measured for payment)
FOAM FILLER:
Polyethylene foam filler cut to suit profile at all ends to ensure air tightness.
SHEETING:
a) rackdeck KLIPPON AZ 150 SMP colour coated ( in approved colour) or equivalent
profile, suitable for purlin spacing upto 1.8 m c/c.
b) 0.50 mm thick without coating with 0.55 mm total coat thickness.
c) 550 MPA yield stress cold Rolled Steel ASTM A446 Grade E)
d) Hot dip metallic coating confirming to AZ150 of AS 1397 with hot dip metallic
coating of 55% Al and 45% Zn alloy having total coating mass of min 150 gms/m2
inclusive of both sides.
e) Measurement is installed area ( net area overlap will not be counted)
f) All overlaps sealed with neutral cured silicon sealants.
115 Roof Accessories M2 1520
Supplying and fixing Zincalume accessories like cappings, flashings, ridges etc.
compatible to sheeting as per item code 114 but in plain sheet including all neutral
coloured silicone rubber sealants, fasteners, washers, bolts, nuts and any other
specials etc. complete as directed & instructed by MMCI / HPCL Engineer In
charge
116 Translucent sheet M2 700
Supplying and fixing Polycarbonate sheet roofing compatible with Zincalume sheet
with all accessories,washer,bolts, nuts as necessary for f ixing complete as
directed & instructed by MMCI / HPCL Engineer
117 MS Fan Hooks Nos 70
Supplying and fixing in position fan hooks of M.S. 16mm dia bar
and 450mm long in concrete slab as shown in drg. and as
directed including painting with one coat of primer and two coats of
synthetic enamel as directed & instructed by MMCI / HPCL
Engineer Incharge.
118 450 mm dia sweep Exhuast fan Nos 22
Supplying & fixing of 450 mm sweep Exhuast fan of Crompton Greaves or its
equivalent make approved by HPCL. Scope includes supplying & Wiring with 3 runs of
3/0.29 PVC insulated copper conductor in suitable 2 MM thick PVC pipe in concealed
manner and in 16 SWG MS conduit for the wiring above the finished surface, having
5A/6A switch control on suitable MS cover with box including 3/036 PVC insulated
copper conductor for light, fan points etc. as required. Work includes all wiring
accessories complete as reqd & include cost of switches of Anchor ROMA make ,ceiling roses, extension rods etc. , cost of digging chases & refilling the same with CM
1:4 & making the wall good as required.
119 Switch Sockets:
5/16A Switch socket point( Regular Switch Socket ) Nos 40
42
7/28/2019 BOQ for Civil-Bhatinda
16/19
Item
No.D E S C R I P T I O N Unit Quantity
Supply and fixing of 3 - pin, 250V, 5/16A switch and socket combined with indicator
and fuse on suitable MS cover with box in concealed manner. Scope includes supplying
and run of 2.5 Sq.mm PVC insulated copper conductor in suitable 2 mm thk. PVC pipe
in concealed manner and in 2mm MS conduit for the wiring above the finished surface
from power plug to power DB etc. complete as required.
120 16/32A Switch socket Nos 20
Supply and fixing of TPN, 415V, 16/32A switch and socket combined with indicator and
fuse on suitable MS cover with box in concealed manner. Scope includes supplying andrun of 4 Sq.mm PVC insulated copper conductor in suitable 2 mm thk. PVC pipe in
concealed manner and in 2 mm MS conduit for the wiring above the finished surface
from power plug to power DB etc. complete as required.
121 20A A.C. Points Nos 20
Same as above item but for supplying & Supplying 20A AC points wherever necessary
as directed by the Site-in-charge.
Lighting & Power Distribution Boards:
122 100A TPN DB with MCCB+ELCB Nos 2
Supply, Installation, Testing and Commissioning of Indoor 3-ph PDB comprising of 1
No. 100 A TPN MCB + ELCB as incomer feeders, 13 Nos., 20 A SPN MCBs as
outgoing feeders. dust & vermin proof (IP-42 protection). It shall be fabricated from 16
SWG CRCA sheet steel enclosure & shall be of compartmentalised type (incomer,
outgoings & termination compartments). LDBs shall be provided with 100 A tinned
copper phase and neutral bars and earth bar of suitable size with earth connection
brought to outside. LDBS shall be suitable for bottom cable entries. Knock outs shall be
provided to receive incoming & outgoing cables. DBS shall be supplied with DIN-
channel, neutral link & busbars. The bus bars shall be of Electrical grade aluminium &
shall be supported rigidly to withstand fault level of 16KA for 1 sec. DBs shall undergo a
treatment of degassing. pickling and two coats of primer before painting with two coats
of antocorrosive enamel paint
123 63A TPN DB with MCB+ELCB Nos 3
Supply, Installation, Testing and Commissioning of Indoor LDB comprising of 1 No. 63
A TPN MCB + ELCB as incomer feeders, 16 Nos. 10A SPN MCBs as outgoing
feeders. dust & vermin proof (IP-42 protection). It shall be fabricated from 16 SWG
CRCA sheet steel enclosure & shall be of compartmentalised type (incomer, outgoings
& termination compartments). LDBs shall be provided with 100 A tinned copper phaseand neutral bars and earth bar of suitable size with earth connection brought to outside.
LDBS shall be suitable for bottom cable entries. Knock outs shall be provided to receive
incoming & outgoing cables. DBS shall be supplied with DIN-channel, neutra link &
busbars. The bus bars shall be of Electrical grade aluminium & shall be supported
rigidly to withstand fault level of 16KA for 1 sec. DBs shall undergo a treatment of
degassing. pickling and two coats of primer before painting with two coats of
anticorrosive enamel paint
124 32A TPN DB with MCB+ELCB Nos 7
Same as above but for Indoor 3- Phase LDB comprising of 1No.32A TPN MCB + ELCB
as incomer feeder. 8 Nos. 10A SPN MCBs as outgoing feeders.
125 Tube light fittings -- BJSM 02 Nos 90
Supplying & fixing of commercial decorative type tube light fittings of Bajaj (Model
no:BJSM 02 236)/Philips or its equivalent make approved by HPCL. Scope includes
supplying & Wiring with 3 runs of 3/0.29 PVC insulated copper conductor in suitable 2MM thick PVC pipe in concealed manner and in 16 SWG MS conduit for the wiring
above the finished surface, having 5A/6A switch control on suitable MS cover with box
including 3/036 PVC insulated copper conductor for light, fan points etc. as required.
Work includes all wiring accessories complete as reqd & include cost of switches of
Anchor ROMA make, ceiling roses etc. , cost of digging chases & refilling the same with
CM 1:4 & making the wall good as required
Note: The distance from the switch board to tube light fitting shall be approx. 20 m..
126 Tube light fittings -- BJSM 14 Nos 10
Same as above but for supplying & fixing tube light fittings of Bajaj make BJSM 140 or
its equivalent model of Philips/ Crompton make approved by HPCL.
127 Tube light -Industrial type Nos 100
42
7/28/2019 BOQ for Civil-Bhatinda
17/19
Item
No.D E S C R I P T I O N Unit Quantity
Supplying & fixing of Industrial type tube light fittings of Bajaj (Model no:BJI 240
FG)/Philips or its equivalent make approved by HPCL. Scope includes supplying &
Wiring with 3 runs of 3/0.29 PVC insulated copper conductor in suitable 2 MM thick
PVC pipe in concealed manner and in 16 SWG MS conduit for the wiring above the
finished surface, having 5A/6A switch control on suitable MS cover with box including
3/036 PVC insulated copper conductor for light, fan points etc. as required. Work
includes all wiring accessories complete as reqd & include cost of switches of Anchor
ROMA make, ceiling roses etc. , cost of digging chases & refilling the same with CM 1:4
& making the wall good as required.
128 Philips TBS-305/218 M5 HPF-2X1 Nos 10
2X18 W Mirror optic recessed mounting, Flourescent Tube light fitting, PHILIPS TBS-
305/218 M5 HPF or equivalent model of Bajaj/crompton Make
129 Philips TBS-305/418 C6 HPF-4X1 Nos 10
4X18 W Mirror Optic , High efficiency, Recessed Mounting Flourescent tubelight Fitting,
PHILIPS TBS-305/418 MI HPF or equivalent model of Bajaj/crompton Make
130 PHILLIPS FCS 31/211-2 X 11 W S Nos 10
2 X 11 W Surface mounted, low profile, Mirror optic fitting FOR PL-S Lamp, Philips FCS
31/211 or equivalent model of Bajaj/crompton Make
131 Philips FBH 145-1X 10 W Recess Nos 10
1X 10 W Recessed Downlight, Wall washer type, PL-C Lamp, Philips FBH 145 or
equivalent model of Bajaj/crompton Make
132 Philips FDN 620/01-1X9 W Low d Nos 5
1X9 W Low Depth, Recessed Downlight, Wall waher type, PL-S Lamp, Philips FDN
620/01 or equivalent model of Bajaj/crompton Make
133 Philips FDN 622/01-1X 9 W Rec Nos 5
1X 9 W Reecessed Downlight, FOR PL-S Lamp, Philips FDN 622/01 or equivalent
model of Bajaj/crompton Make
134 1200 mm dia Ceiling fan Nos 30
Supplying & fixing of 1200 mm sweep Ceiling fan of Crompton Greaves or its
equivalent make approved by HPCL. Scope includes supplying & Wiring with 3 runs of
3/0.29 PVC insulated copper conductor in suitable 2 MM thick PVC pipe in concealed
manner and in 16 SWG MS conduit for the wiring above the finished surface, having
5A/6A switch control on suitable MS cover with box including 3/036 PVC insulated
copper conductor for light, fan points etc. as required. Work includes all wiring
accessories complete as reqd & include cost of switches of Anchor ROMA make ,
ceiling roses, extension rods etc. , cost of digging chases & refilling the same with CM1:4 & making the wall good as required.
135 Telephone
2 Pair telephone wiring as mentioned below RM 500
Supply & laying of 2 pairs of 0.5 mm dia screened & shielded telephone wire in 20 mm
dia PVC conduit partly/fully concealed in types of walls, floor etc. complete with all
accessories, wiring terminators, connected civil works, rough plastering etc including
supply of 16 SWG GI fish wire conduit and accessories
136 RJ 11 Telephone connectors Nos 20
Supply & fixing of modular type telephone connectors in suitable size PVC box
concealed to wall including all civil works.
137 20 pair telephone junction box Nos 5
Supply & fixing of 20 pair telephone tag block with crone connectors housed in suitable
MS junction box.
138 Fire Alaram System2 Pair fire alarm wiring as mentioned below RM 500
Supply & laying of 2 pairs of 2.5 mm core dia Un armoured FRLS Cable in 25 mm dia
MS conduit partly/fully concealed in types of ceiling, walls, floor etc. complete with all
accessories, wiring terminators, connected civil works, rough plastering etc including
supply of 16 SWG GI fish wire conduit and accessories
139 Back Box / Pull box with 4 terminals Nos 50
Supply & fixing of 4 terminal MS back box /pull box.
140 TAS LAN
CAT 6, 4 pair twisted pair computer cable for TAS LAN RM 200
Supply & laying of CAT 6, 4 pair twisted computer cable screened and shielded in 20/25
mm dia PVC conduit partly/fully concealed in types of walls, floor etc. complete with all
accessories, wiring terminators, connected civil works, rough plastering etc including
supply of 16 SWG GI fish wire conduit and accessories
141 RJ 45 Computer Connectors Nos 15
Supply & fixing of modular type of RJ 45 computer connectors in suitable size PVC box
concealed to wall including all civil works.
142 CCTV
Co-axial braided cable RM 50
42
7/28/2019 BOQ for Civil-Bhatinda
18/19
Item
No.D E S C R I P T I O N Unit Quantity
Supply & laying of co axial, braided cable in 20/25 mm dia PVC conduit partly/fully
concealed in types of walls, floor etc. complete with all accessories, wiring terminators,
connected civil works, rough plastering etc including supply of 16 SWG GI fish wire
conduit and accessories
143 BNC CCTV Connectors Nos 3
Supply & fixing of modular type of RJ 11 computer connectors in suitable size PVC box
concealed to wall including all civil works.
144 MIS LAN
CAT 6, 4 pair twisted pair computer cable for MIS LAN RM 600
Supply & laying of CAT 6, 4 pair twisted computer cable screened and shielded in 20/25
mm dia PVC conduit partly/fully concealed in types of walls, floor etc. complete with all
accessories, wiring terminators, connected civil works, rough plastering etc including
supply of 16 SWG GI fish wire conduit and accessories
145 RJ 45 Computer Connectors Nos 15
Supply & fixing of modular type of RJ 45 computer connectors in suitable size PVC box
concealed to wall including all civil works.
146 150 mm dia GI Pipes for sleeves in trenches RM 15
Providing, supplying and laying 150 dia. G.I pipes below grade slabs/embedded
in foundations, for laying electrical/instrument cables.Etc complete as per drawings
& instructions of MMCI/HPCL Engineer in charge.
147 100 mm dia GI Pipes for sleeves in trenches RM 15
same as item no 146 but with 100 mm dia G.I pipe
148 80 mm dia GI Pipes for sleeves in trenches RM 10same as item no 146 but with 80 mm dia G.I pipe
149 SHALITEX BOARD EXPANSION JOINT M2 20
Supplying and fixing in position 25 mm thick SHALITEX BOARD EXPANSION joint for
columns and between walls at all heights. SHALITEX board shall be manufactured by
M/s SHALIMAR TAR products or equivalent as per their standard specifications.
42
7/28/2019 BOQ for Civil-Bhatinda
19/19
Item
No.D E S C R I P T I O N Unit Quantity
150 POLYSULPHIDE SEALANT RM 15
Supplying and applying in position two part exterior grade polysulphide sealant on the
expansion joint. The sealant shall be of PIDISEAL PS 41G of M/s Pedilite Industries or
equivalent. The sealant shall be applied all as per manufacturer's specifications and
recommendations. Appropriate primer, masking tapes etc should be applied. The
sealant shall be maximum 50 mm in thickness and of maximum depth of 25 mm.
The rate shall be inclusive of providing and fixing breaker rod as per detail architectural
drawings.
151 GYPSUM BOARD FALSE CEILING M2 130
Supplying and fixing SUSPENDED FALSE CEILING at any level which includes
providing and fixing GI perimeter channels of size 0.55 mm thick having one flange of
20 mm and another flange of 30 mm and a web of 27 mm alongwith perimeter of ceiling,
screw fixed to brickwall / partition. Then suspending GI intermediate channels of size 45
mm 0.9mm thk.. with two flanges of 15 mm each from the soffit at 1220 mm centers
with ceiling angle of width 25mm x 10 mm x 0.55 mm thk.. Fixed to soffit with GI cleat
and dash fasteners. Ceiling section of 0.55 mm thk.. having knurled web of 51.5 mm
and 2 flanges of 26 mm each with lips of 10.5 mm are then fixed to the intermediate
channel with the help of connecting clips and in direction perpendicular to the
intermediate channel at 457 mm centers. 12.5 mm tapered edge Gypboard (conforming
to IS-2095-1982) is then screw fixed to ceiling section with 25 mm drywall screws at 230mm centers.
Finally square and tapered edges of the boards are to be painted and finished so as
to have a flush look which includes fill ing and finishing with jointing compound and
paper tape and two coats of primer suitable for GYPBOARD. (as per recommended
practices of INDIA GYPSUM or equivalent)
PAINT FINISH : -
Providing and applying 2 coats of PLASTIC EMULSION paint of approved
manufacturers, on the GYPBOARD surface including necessary surface preparation
such as scrapping, brushing, cleaning etc. all complete.
Please Note :
(a) The False ceiling contractor shall provide suspension system / necessary framing for
light fixtures, collars for return air grills as well as A.C. diffusers.
(b) Measurements shall be wall to wall without any deductions for Light Fixtures,diffusers, columns etc.
152 FALSE FLOORING M2 40
Supply and installation of UNITEC JEC or equivalent make raised flooring type FS-1200-
30G steel panel 600x600x30mm along with bolted stringer of height(500-600 mm) with
Antistatic laminate top as per drawing and manufacturer's specification complete.
153 Precast Slab M2 100
Supplying & fixing precast RCC Slab of 75 mm thk. in M20 Grade in drain,pit,trench
covers including shuttering,finishing smooth with 6 mm thick cement plaster (1:3)
on exposed surface complete including transport at site & placing in position all
complete including reinforcement fixing (R/F should be pain separate item) as per
drawing and specification
154 150 Dia Hume Pipe RM 40Supplying & Laying cement concrete pipes of NP-2 Class of 150 mm dia in proper line
level & slope including supply & fixing of collars in cement mortars 1: 2 with curing
complete as per specification & drawing.
155 300 Dia Hume Pipe RM 40
Supplying & Laying cement concrete pipes of NP-2 Class of 300 mm dia in proper line
level & slope including supply & fixing of collars in cement mortars 1: 2 with curing
complete as per specification & drawing.
156 Point wiring for light fixture Nos 100
Point wiring including circuit wiring using 3/0.29 PVC insulated copper wire of approved
make, in existing PVC conduit for lighting fixtures. Job to be carried out through existing
conduits, existing wired conduits etc of various buildings inside HPCL premises. The
payment is on point basis for all lengths. The rates shall include supply of modular type
switches, sockets, regulators, metal boxes, all accessories required for completion of
the point, cost of digging chases & refilling the same with CM 1:4 and making good thewall back to original condition ; exclusive of fixing charges of DBs, light fittings, fan
fittings etc.
Top Related