BOQ for Civil-Bhatinda

7/28/2019 BOQ for Civil-Bhatinda

1/19

Item

No.D E S C R I P T I O N Unit Quantity

CIVIL1 Excavation up to 1.5 m depth M3 7670

Excavation in all types of soil viz. sand, clay, soft & hard murum etc.

(excluding soft/hard rock) for footings, steps, plinth beams, equipment

foundations, drains, trenches, manholes, underground tanks, etc

including shoring, strutting, dewatering wherever required (until foundation work

is complete). Item also includes carting, stacking if required by MMCI / HPCL ,

Engineer In Charge ,spreading, levelling and compacting/ consolidating surplus

materials with any lead within HPCL's premises or as per instruction of

MMCI / HPCL Engineer In Charge (Rate includes removal of any vegetation,

small shrubs etc.)

2 Excavation from 1.5m to 3.0 m depth M3 210

Same as item 1 above but for 1.5 m to 3.0 m depth

3 Filling with excavated earth M3 5210

Filling the sides of foundations, sub-structures etc. with approved quality

of earth laid in layers not exceeding 300 mm in loose thickness including

levelling, watering, ramming, rolling, compacting with 10-12MT mechanical roller /

hand compactor/mechanical rammer to 95% Modified Proctor Density etc.

complete with any lead within HPCL's premises as directed and instructed by

MMCI/HPCL Engineer Incharge. (Note: Item doesnot include excavation)

4 Filling with imported murum M3 4915

Supplying and filling murum below grade slab / within plinth of approved quality with

PI of 1 to 7(Low plastic) containing not more than 20% cohesive fines namely clay

and Max. dry density of material not less than 1.80 gms/cc, including

identifying & locating of borrow pits, excavation at borrow pits outside Plant

premises; payment of Royalty to Owner of borrow pit, if applicable; payment of

applicable royalties, taxes, etc to Statutory Authority for operating the borrow pit;

loading at borrow pit end; transportation from borrow pit to HPCL Premises;

removing debris, organic matter, etc; spreading in layers not exceeding

300mm loose depth; dewatering during course of filling, watering, compacting to

obtain 95% of modified proctor maximum laboratory dry density all complete as

per specifications and instructions of MMCI/HPCL Engineer-in-Charge.

5 Disposal of surplus excavated earth M3 2670

Disposal/carting away surplus excavated earth / debris etc. outside HPCL's

LPG Plant premises to unobjectionable place identified by vendor.

6 Sand Filling M3 150

Supplying and fil ling locally available good quality river sand in trenches, pits etc in

layers of 150 mm thick including watering and compacting to achive 95 % Modified

Proctor Density etc all complete as per instructions of MMCI/HPCL Engineer-in-

Charge.

7 PCC (1:3:6): M3 100

Supplying and laying Plain Cement Concrete of nominal volumetric mix 1:3:6(1 Cement:

3 Sand: 6 Crushed stone aggregates) with 40mm and down size graded aggregates

below RCC foundations any other work as per requirement including any required

permanent brick masonry, shuttering, dewatering, tamping, ramming, curing, etc allcomplete as per instructions of MMCI/HPCL Engineer-in-Charge

8 PCC M15 M3 800


2Sand:4 Crushed stone aggregates) with 20mm and down size graded aggregates

below plinth protection & any other work as per requirement including any required

permanent brick masonry, shuttering, dewatering, tamping, ramming, curing, etc all

complete as per instructions of MMCI/HPCL Engineer-in-Charge

42


2/19

Item


9 PCC ( 1:4:8) M3 325


4 Sand: 8 Crushed stone aggregates) with 40mm and down size graded aggregates

below RCC foundations any other work as per requirement including any required

permanent brick masonry, shuttering, dewatering, tamping, ramming, curing, etc all

complete as per instructions of MMCI/HPCL Engineer-in-Charge

10 RCC M25 upto Plinth level M3 2690

Supplying & laying in position Controlled grade Reinforced cement Concrete for

footings, foundations, rafts, pedestals, columns, beams, walls,

staircases, trenches, manhole pit, equipment foundations, grade slabs

(including expansion, construction, control, isolation joints etc), kerbstones

encasing of pipes etc at depth below and upto plinth level. with design mix of

required grade at all locations and levels using 20mm size and down graded

aggregates in all types of works [including leaving pockets, placing of conduits,

making openings, pockets placing inserts/ sleeves in columns/ beams/ slabs

etc.] machine mixing, lifting, placing, machine vibrating, tamping, curing etc. as

specified, complete without Reinforcement as per drawings & / or as directed by MMCI

/ HPCL Engineer Incharge.

NOTE: 1) The rate also includes cost of Supplying offsets, cutouts,good quality

plywood shuttering,props, construction joints, making holes in or cutting formwork for

taking out dowel bars, hacking the exposed surfaces to receive plaster as

necessary.

NOTE: 2) To get required workability or for any other reason whatsoever if

additives, plasticizers etc. are to be added the cost of procuring and adding

the same shall be included in the cost of concrete unless specified otherwise.

NOTE: 3) All testing of concrete quality as per relevant IS shall be under the scope.

11 RCC Grade M20 M3 380

Same as Item no 10 but for M20 Grade concrete in grade slab,paving etc.

12 RCC Grade M25 above Plinth M3 1475

Same as Item no 10 but Concrete for RCC works at all levels above plinth level for

all structures, columns, beams, floor slabs, roof slabs,

sunshades , lintels, staircases, fins, chajjas, pardis, sills, copings, projections,column/ beam encasings etc.(up to a ht.of 12 mts.) from plinth level.

13 MS Round Bars MT 1

Supplying, laying & fixing in position MS reinforcement of Fe 250 conforming to IS

432- part 1 for hold fast, locations & levels including cutting, bending & welding to

insert plate etc. complete as specified and directed by Engineer/HPCL Engineer

Incharge.

14 CRS bars for Reinforcement MT 440

Supplying ,cutting,bending and placing in position HYSD TMT Bars conforming to IS:

1786 Fe415 or Fe 500 , for foundation raft, beams, slab, columns, etc. including

transporting the steel, straightening, cleaning, decoiling, to required shapes and lengths,

binding with Contractors own 16 gauge SWG binding wire at every intersection ,

supplying and placing with proper cover blocks, supports, chairs, overlaps, spacers, etcall complete as per specifications and bar bending schedule approved by MMCI/HPCL

Engineer-In-Charge.

42


3/19

Item


15 Anchor / Foundation Bolts MT 8.5

Supplying, fabricating and fixing in position M.S. round holding down (foundation) bolts

with nuts and check nuts, washers, pipe, plates, etc., all complete as per instructions of

MMCI/HPCL Engineer-in-Charge

NOTES:

1. The rate to include cost of bolt and also to include Supplying and welding holding

arrangements such as plate or angle at bottom.

The rate also to include preparing and fixing template for keeping the bolts at correct

centres before, doing and after concreting.

16 Providing pockets -300mm deep Nos 10

Forming pockets for anchor bolts, etc in concrete, including supplying & fixing

necessary templates supports and setting out, including protecting the pockets from

filling up, plan area not exceeding. Depth upto 300mm

17 Providing pockets >300mm deep Nos 10

Same as above but depth >300mm to 700mm

18 Precast RCC for ornamental work

Providing, hoisting and fixing precast reinforced cement concrete in slabs/

bresummers /mouldings/vertical & horizontal fins/forming box louvers band, facias,

eaves board etc. including setting in cement mortar 1:3 (1 cement: 3 corase sand),

cost of required centering, shuttering and finishing smooth with 6 mm thick cement

plaster 1:3 (1 cement: 3 fine sand) on exposed surfaces but excluding the cost of

reinforcement with 1:11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate

20 mm nominal size) for Mughapu for Gate cabin etc. and castings over gate entry and

any other ornamental work required and as directed by the Site-in-charge.

M3 10

19 Cast-in-situ RCC for ornamental work

Providing, hoisting, casting reinforced cement concrete in slabs/ bresummers

/mouldings/vertical & horizontal fins/forming box louvers, band, facias, eaves board etc.

including setting in cement mortar 1:3 (1 cement: 3 corase sand), cost of required

centering, shuttering and finishing smooth with 6 mm thick cement plaster 1:3 (1

cement: 3 fine sand) on exposed surfaces but excluding the cost of reinforcement with

1:11/2:3 (1 cement: 11/2 coarse sand: 3 graded stone aggregate 20 mm nominal size)

for Mughapu for Gate cabin etc. and castings over gate entry and any other ornamental

work required and as directed by the Site-in-charge.

M3 50

20 Insert Plates / Nosing angles / Channels MT 16

Supplying, fabricating and fixing in position at required locations to correct lines and

levels, angles, inserts for pits in shed & stairs , cable trenches and all types of

RCC, PCC & masonry incl. necessary holdfasts , welding, machining, grinding,

threading etc.Exposed surface will be thorughly cleaned & painted with epoxy

primer & paint. (All materials & accessories required shall be provided by

Contractor).

21 Non Shrink Grout M3 2

Supplying and laying under equipment, grouting pockets etc GROUT made from

Non Shrink Compound ( all as per manufacturer's specification & approved by

MMCI/ HPCL Engineer Incharge. )

22 Ordinary Grout M3 7

Grouting below column bases including anchor bolt pockets / pipe sleeves, etc. with

cement grout of 1:2 mix ( 1 cement :2 sand ) including supply of all materials, labour,

tools, plant shuttering, strutting, curing, with all leads and lifts, etc., all complete as per

instructions of MMCI/HPCL Engineer-in-Charge

23 UPVC Rainwater pipes RM 875

Providing, laying and fixing in position on surface with necessary MS Clamps

and wooden blocks of approved quality U-PVC 110 dia rain water pipes of Class I

to IS 4985 wherever required specials including lead caucking joints, testing

and painting the pipes wherever required with 3 coats of approved oil paint in

approved colours. (Specials shall include all bends, offsets, shoes, junction

etc. Rate shall be inclusive of such specials measured on linear basis.)

24 Epoxy Bonding Agent M2 2

Supplying & applying epoxy bonding agent between old concrete to new

concrete inclding preparation of surface at levels complete as per manufacturer's

specification & as directed & instructed by MMCI/ HPCL Engineer Incharge.

25 Anti-termite treatment M2 2100

42


4/19

Item


Supplying anti-termite treatment using CHLOROPYRIPHOS 20% EC (ISI marked) in

1% concentration as per IS 6313 of 1981 by creating a chemical barrier under and

around the wall, footings, plinth & foundations junction of wall & floor along the

external perimeter of building, conduits etc as per IS 6313 all complete as per

instructions of MMCI/HPCL Engineer-in-Charge

(Mode of measurement shall be plinth area only).

26 Structural Steel Work MT 520

Supplying raw steel as per IS:2062, fabricating, welding and/or bolting, as required,

erecting and fixing in position all types of structural steel work viz rafters, trusses,

purlins, beams columns,plates sag rods, shop/site fabricated including all accessories

viz. nuts, bolts, cleats, gussets, etc as per specification complete as directed by

MMCI/HPCL Engineer in charge. The rate to include for welding weights, site

connection, nut & bolts and same will not be measured for payment .

42


5/19

Item


Supply of all consummables shall be under contractor'scope.

27 Chequered plate MT 8

Same as item no.26 but for 6 O/P chequered plate fixed over trench or other

pit covers including supply of plates & consummables.

28 Grating M2 200

Same as item no. 26 but for gratings of designed size & shape fixed over

walkways,platforms, stairs etc including supply of all materials &

consummables with painting complete as per drg & specification.

29 Tubular Steel Work MT 0.5

Supplying,transporting,fabricating,loading,unloading& erecting in position to the

required line & level,steel work made out of tubes as per IS1161 Gr Yst210 or as

per IS1239 for trusses,bracings,tie runners,pipe supports,towers& cleats,base

plate gussets,grits,purlins,side runners etc.including cutting,welding,bolting ,

threading,preparation for fabrication including painting,staging,scaffolding etc.

as directed by MMCI/ HPCL Engineer incharge.

30 Painting MT 520

Surface preparation by wire brushing free of scales with 2 coats of

zinc rich primer (total DFT-75 microns) & 2 coats of first quality synthetic enamel

paint (total DFT-50 microns) as approved by MMCI / HPCL

engineer in charge

31 Pipe Railing RM 150Supplying, fabricating & erecting pipe handrailing made out of M.S. "C" class pipes

(appr. 1050mm high) with 32NB dia. pipe hand rail, 2-20mm NB dia pipe knee rails

and 100 x 5mm thk. toe plate with 32NB pipe vertical support spaced at

approx.1500 c/c and at corners & change of direction. Also including assembly for

fixing to inserts or stringer beams complete in all respects including surface

preparation for painting and 2 coats of red oxide zinc chromate primer & two coats

of 1st quality synthetic enamel paint of approved make & shade all as directed &

instructed by MMCI / HPCL Engineer incharge NOTE:

Items shall be measured as total length of completed pipe railing. (not individual

pipe lengths)All sections shall be of IS:2062.

Supply of all consummables shall be under contractor'scope.

32 230 thk Brick Masonry in CM 1:5 M3 1310

Supplying & constructing 230 thk brick masonary walls using bricks of first class burnt

clay (class 3.5 as per IS:12894, Compressive strength of Brick 35 kg/cm2) ofapproved source at all locations and levels including scaffolding, racking of joints,

watering but excluding cement plaster finish with cement mortar(1:5)complete

as directed and instructed by MMCI / HPCL Engineer incharge.(up to a lift of 12 mts.).

33 110 thk half Brick Masonary(1:4) M2 500

Supplying and constructing 110mm thickburnt clay brick masonry in super structure

using first quality bricks (class3.5 as per IS:12894, Compressive strength of

Brick 35 kg/cm2) of approved source in cement mortar (1:4) including necessary

scaffolding, racking of joints, watering but excluding cement plaster finish complete

as directed and instructed by MMCI / HPCL Engineer incharge.(up to a lift of 12 of

mts.) Transoms & mullions shall be provided in the brick work when length or

height of wall exceeds 2M. Transoms shall be provided at lintel/door height.

Spacing of mullions shall not exceed 1.5M c/c. Size of transoms/mullions shall be

115mm x 115mm with M15 grade concrete & 10mm down graded aggregate only.Supplying and placing formwork etc for transoms/mullions etc shall be included in

the quoted rate.

34 12 mm thick Plaster M2 3900

42


6/19

Item


Supplying & doing 12mm thick cement plaster in C.M. 1:4 mix finished with neeru.as

per specification to all RCC & masonry work at all levels and locations including

grooves, pattas, drip moulding, scaffolding, watering, hacking out joints in masonry or

concrete work as per specification. The rate to include Supplying and fixing of 200mm

wide chicken wire mesh of 26G & 15mm mesh size with minimum overlap of 150 mm at

the junction of different construction materials all complete as per instructions of

MMCI/HPCL Engineer-in-Charge

35 6 mm thick Plaster M2 2050

Supplying and applying max. 6 mm thick cement plaster in C.M. (1:3), finished with

Cement slurry to ceilings or elsewhere as directed; including pattas grooves in all

positions, including necessary scaffoldings, curing, with all lifts and leads, rubbing with

small trowel etc. all complete as per instructions of MMCI/HPCL Engineer-in-Charge

36 12 mm thick Plaster & 8 mm thick plaster ( combined 20 mm) M2 5000

Supplying and doing sand faced plaster 20mm thk in C.M. 1:5 & 1:2 in 2 coats of 12

mm & 8 mm respectively to all RCC and masonry works at all locations and levels

including required grain finishing, curing etc. complete as per specification and as

directed and instructed by MMCI/HPCL Engineer in charge.

NOTE: Rate to include the cost of the base coat of not less than 12 mm thickness,

external coat 8 mm thk. hacking, scaffolding, grooves, patta, drip moulds, curing and

Supplying and fixing 150mm wide G.I. chicken mesh 26g thk & 15mm mesh size with

minimum overlap of 150 mm at junctions of brick and RCC/PCC work etc. as well as

Supplying and mixing waterproofing compound of approved make in both coats as per

manufacturers specifications all complete as per instructions of MMCI/HPCL Engineer

37 20 mm thick Waterproofing Plaster M2 15

Same as item no 34 above but for 20 mm/ 12mm thick back up plaster for internal surface

of RCC/Masonry work which is to be tiled.

38 Rubble Soling M2 7525

Supplying and doing 230 mm thick dry rubble stone packing/soling under

floor, foundation, pavement, roads,steps,ramps & other similar locations,

handset vertically in rectangular lines, interstices filled in with smaller stone

chips including watering, compacting/consolidating & finishing to the required

levels and lines etc with the use of 10 Ton roller and with mechanical rammers

complete as directed. (Blinding layer shall be of metal, sand or murrum.)39 Cudappah Stone Flooring 30mm thick M2 50

Supplying & laying in floor approved quality machine cut, machine polished cudappah

stones of specified size and thickness in green or grey or approved tint in pattern or

layouts as per drawing over a bed of 20mm C.M.1:4 including curing & polishing

smooth as per specifications & as directed & instructed by MMCI / HPCL Engineer

Incharge)

40 Cudappah Stone Skirting RM 35

Same as item no 39 above but for 30mm thk polished cudappah stone in

treads , riser , landings & skirting.

41 Marble Tiles in floors M2 25

Supplying & fixing 1st class quality Marble tiles of approved make & colour & size as

directed with thickness 25mm including corners and curves laid with white cement

under bed of 25 mm cement mortar 1:3 including curing, machining,polishing smoothin floor as per drawing, specification & as per instruction of MMCI / HPCL Engineer

Incharge.

42 Marble Tiles In skirting RM 18

same as item no 41 above but in skirting

43 18 mm thk. Granite slabs in floors M2 125

Providing & fixing 18mm thick mirror polished, machine cut black granite slab of size

1.0 to 2.0 sqm for kitchen platforms, vanity counter facias, floors and similar

locations laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand)

with joints treated with white cement, mixed with matching pigment, epoxy touch

ups, including rubbing, curing etc. complete at all levels.

44 Granite slab in skirting RM 200

Same as item 43 above bu in skirting

45 Edge moulding for granite slab RM 400Providing edge moulding to 18mm thick granite stone for counters, vanities etc. over

item above including machine polishing to edge to give high gloss finish etc. complete

as per design approved by Engineer-in-charge.

46 Eurocon Cement Tiles M2 800

Supplying & fixing cement tiles of approved make & red colour laid over bedding of

cement mortar (1:3) of appropriate thickness in approved design & pattern over sloped

42


7/19

Item


or flat roof ,in porches, in walkways( as per detailed architectural drawings all as directed by

MMCI/HPCL Engineer Incharge.)

47 Glazed MP tiles M2 550

Supplying and laying of glazed Mangalore Pattern (MP) first quality tiles of 400 mm or

nearest size over the cement mortar reaper bands (already provided) to connect lines

and levels at all heights as directed by the Site-in-charge.

48 Glazed MP hip and ridge tiles RM 140

Supplying and laying first class glazed MP hip and ridge tiles set in cement mortar 1:3

including finishing edges neat, etc. complete as directed by the engineer-incharge

49 Vitrified Tiles For Flooring M2 800

Supplying and laying in position polished 1st quality vitrified tile ( 600mm x 600mm

x 10mm thk.) of approved make for FLOORING laid laid over bedding of cement

mortar 1:3 (of appropriate thickness) in approved design and pattern and (NOTE :

The vitrified tile flooring shall be laid in pattern (as per detailed Architectural drawing

or as directed by MMCI/HPCL Engineer Incharge.)

50 Skirting RM 560

Same as item no 49 but for skirting

51 Ceramic Tiles for Flooring M2 220

Supplying & fixing 1st quality ceramic tiles of approved make & colour & size as

directed thickness 7mm incl. corners and curves laid on C.M. 1:4 bedding of

required thickness with neat cement float and filling joint with white/ coloured

cement in flooring all as directed and instructed by MMCI / HPCL Engineer

Incharge.

52 Skirting RM 160

Same as item no 51 but for skirting

53 Ceramic Tiles for Dado M2 25

Same as Item No. 51 above but in dado/skirting to

give surface flush with plastered/painted surface.

54 Damp proof course M2 108

Supplying & laying damp proof course 40mm thick in P.C.C. 1:2:4 using 12mm

42


8/19

Item


size & down grade aggregate mixed with "Cico" or other equivalent

waterproofing compound 3% by weight of cement or as per manufacturers

specifications finished rough including cleaning, curing etc complete as

specified and as directed by MMCI / HPCL Engineer Incharge.

55 Wateproofing for roof / chajja / canopy / RCC Gutters (Polyurethane type) M2 1870

Supplying and applying Polyurethane treatment to roof slab / Chajja /

canopy / RCC Gutters etc as per the manufacturers specifications etc

complete including cleaning, washing, and curing as specified etc complete with

10 years waterproofing guarantee. Note : The mode of measurements for this item

will be the length and breadth of the actual treated surface (i.e. the plan area),

including vata, measured after treatment. No extra will be paid for the vata.

56 Wateproofing for toilet sunk M2 150

Supplying & laying cement based surface water proofing by approved agency for

toilet sunk portion with brickbat coba avg.115mm thk finished at top water proof

scratch coat surface to receive tiling/ floor finishes etc. complete in all respects as

per the specifications with 10 years written guarantee of performance in approved

format all at directed & instructed by MMCI / HPCL Engineer Incharge. NOTE:

(Payment shall be made on measurement of finished plan area only).

57 Mastic Flooring 20 mm thick M2 5690

Supplying & laying Mastic Flooring 20 mm thick anti static & electricallyconductive Mastic flooring confirming to IS 8374 in LPG sheds connecting

Platforms etc.For the horizontal surfaces i.e. floors. Rate to include testing of

one sample at VJTI, Mumbai & submission of report to HPCL

58 Mastic Coating 20 mm on columns/RCC/brickwalls above floor M2 680

Same as item no 57 but for vertical surfaces i.e. columns up to 1.5 m height.

Rate to include Supplying MS chicken wire mesh 20 gauge, required to retain mastic

flooring along vertical surfaces.

59 Ironite Flooring M2 1940

Supplying and laying average 40 mm thick Ironite or approved floor finish in cement

concrete laid in alternate bays in two layers. Bottom layer shall be average 88 mm thick

laid to slope in cement concrete 1:1:2 with 10 mm to 6mm graded stone aggregates

finished rough. Top layer shall be 12mm thick metallic floor hardener finish in Ironite orapproved in 1:4( 1 metallic compound to 4 cement ) by weight and this dry mixture shall

be mixed with stone aggregates 6mm nominal size in ratio 1:2 ( 1 cement mixture and 2

aggregates) by volume including all formwork , 4mm thick glass separator strips, mixing

, compacting , finishing the surface to required line and levels, trowelled smooth and

curing by ponding , etc, all complete as per instructions of MMCI/HPCL Engineer-in-

Charge

60 Plinth Protection M2 2035

Supplying & doing plinth protection around building or pavement including

excavation, rubble soling 230thk ,100 mm thk 1:3:6 grade concrete with broom finish

& as directed and instructed by MMCI / HPCL Engineer In charge (Reinforcement

shall be paid for separately).

61 Aluminium Glazed Doors M2 80

Supplying & fixing powder coated aluminium single leaf or double leaf doors

with frames of size 100mmx45mmx3.18mm thick, double action with shutterframes of vertical style 85mm x 45mm x 2.5mm thick frame, and horizontals

of 100mm x 45mm x 2.5mm with beading clips, EPDM gaskets, night latch,

stopper, glazing with 6mm, clear float glass panes / obscure glass panes of

special selected quality, full handles on both sides of all shutters made of 75mm

x 8mm anodised alumionium plate, stainless steel screws, hinges,

strengthly of hinged styles of approved hardware etc. complete. & as

directed by MMCI / HPCL incharge

62 Partly glazed aluminium doors M2 35

Same as item no.61 but for Partly glazed and Partly aluminium sandwitch

panel sandwitched with 9 mm thk. marine ply overlaid with 18 guage (1.2 mm)

thick Anodised aluminium sheet on both sides & 5.5 mm float glass glazing.

63 PVC Doors M2 40Supplying & fixing PVC Sintex or equivalent door with shutter consisting of shutter

frame made of extrude plastic section having dimensions of 60x24mm anodized

with multi chambered hollow plastic section of 200x20mm with an average wall

thichness of 1mm jointed with one another by a tongue and groove joints and outer

42


9/19

Item


frame of door made of extruded plastic section of 68x60mm or nearest on all sides

including Supplying and fixing all required fiiting such as anodized aluminium butt

hinges , tower bolts handles with screws,MS hold fasts for fixing door frames etc.

complete as per manufacturer's specification.

64 Rolling Shutter M2 55

Supplying & fixing Hand operated with pull & push type with ball bearing Rolling

shutters of 18 gauge G.I., 75 mm wide rolled plates with 12mm lap, concave

corrugation, complete with "one piece" construction, pressed steel 75mm channel

guides, brackets, flat springs, door suspension shafts, locking arrangement,

including G.I. 20 gauge top hood cover and 2.5mm thick bottom plate All fitted &

fixed all complete as per instructions of MMCI/HPCL Engineer-in-Charge.

(Measurement for the payment shall be for the area of shutter size clear).

65 Pressed Steel Hollow Metal Doors M2 55

Supplying and fixing Hollow Metal Pressed steel doors having Two hours of fire rating

with 16 gauge pressed steel frames of size 125mmx45mm and 45mm thick single

leaf shutters of 18 gauge MS sheets with stiffeners made of channel 25mm

wide x3.15mm thick (depth of channel to suit shutter thickness) spaced not

more than 300mm apart, horizontally, including attachments for fixing all hardware,

fastenings, fixtures and hardware as per drawing with minimum of 3 nos jambs and

hinges, external locks, internal push bars (should be openable from inside even when

locked from outside) with 2 coats of synthetic enamel paint on one coat of zinc

chromate primer all complete as per instructions of MMCI/HPCL Engineer-in-Charge.

(Measurement for the payment shall be for the area of shutter size clear)

66 Aluminium sliding window M2 80

Supplying and fixing in position powder coated aluminium sliding windows with 6

mm clear glass upto 3 tracks in extruded sections, outer frame having weep holes

and water drainage section at bottom including PVC weather strips & glazing

channels, nylon glider, rubber bumpers in interlocking sections, locking

arrangement etc. complete as directed by MMCI / HPCL incharge.

- Sliding portion

67 Aluminium sliding window M2 35

Supplying and fixing in position powder coated aluminium sliding windows with 6mm clear glass upto 3 tracks in extruded sections, outer frame having weep holes

and water drainage section at bottom including PVC weather strips & glazing

channels, nylon glider, rubber bumpers in interlocking sections, locking

arrangement etc. complete as directed by MMCI / HPCL incharge.

- Fixed portion

68 M.S. Steel windows & ventilators M2 180

Supplying and fixing in position GI coated. Steel windows and ventilators as per

relevant IS with standard rolled sections including grit blasting at shop , 6 mm thick

plain sheet glass with necessary holdfasts, oxidised brass fixtures/fasteners, putty,

glazing clips, or aluminium beading, peg stay, handle, screws etc. complete as per

drawing and specifications complete as directed by MMCI / HPCL incharge.

69 Oil bound distemper M2 5

Supplying and applying three coats of Oil bound Distemper (bybrush) to plastered surfaces of wall and concrete

work (internal walls & ceilings) including rubbing with sand paper,

including primer and two coats of palti , scaffolding etc. complete as per

and as directed & instructed by MMCI / HPCL Engineer Incharge.

70 External Paint M2 4000

Supplying 1 coat of approved primer and two coats of Acrylic Emulsion paint of Asian

Make ( ACE Paint) or equivalent of approved shade over concrete or plastered

surfaces, incl. scaffolding, preparation of the surfaces as per manufacturers

specification including cleaning of surface,over a coat of cement primer all complete as

per instructions of MMCI/HPCL Engineer-in-Charge

71 Providing 2 mm thk. Putty M2 7500

Providing and applying putty of 2mm thick over plastered surface to prepare the surfaceeven and smooth , etc. complete

72 Internal Painting M2 7500

Supplying & applying at all heights,of required shade of approved make including

preparation of surface for painting ,applying primer & putty of approved make with

two or more coats of approved quality of ready mixed plastic Emulsion paint

over a coat of white cement primer.

42


10/19

Item


73 Synthetic enamel painting M2 150

Providing and applying synthetic enamel paint, at all heights, of required shade and

approved make on new work including the preparation of surface for painting, applying

primer & putty, of approved make with two or more coats of approved first quality

synthetic enamel paint as directed. all lift and leads.

74 White washing with lime M2 2000

Providing and applying 3 coats of white wash to brick and concrete surface including

providing necessary scaffolding, surface preparation etc. complete. If additional coats

are required to obtain uniform and smooth finish , the same shall be carried out at no

extra cost.

75 Indian WC Nos 10

Supplying & fixing Indian W.C. pan Orissa pattern 580 x 440 mm size with Box

Rim with P or S trap including flushing cistern,flush valve (Front or Rear entry as

required) 100mm dia. C.I. connector upto soil stack or inspection chamber

making flushing water & vent pipe connections with lead pipe for flushing

connection & C.I. pipe for vent connection encasing of flushing connection in

42


11/19

Item


concrete & filling balance portion of W.C. with brick bat concrete etc. complete.

The approved make & colour directed by MMCI / HPCL incharge ( Minimum

sinking of floor to be 45 cms) ( at a distance of 60 cms from door - if sinking is

inclined)

76 European WC Nos 5

Supplying & fixing in position floor mounted European water closet with P

or S trap including flushing cistern & sprout ,flush valve as required - black

commander make. Champion brand seat cover with CP brass hinges rubber

buffers & 100 mm CI connector upto soil stack or Inspection Chamber (as the

case may be) with Supplying & making a hole in wall & making it good and

Supplying & making a flushing connection & vent pipe conection etc.

complete including Supplying all material hhbj fittings etc. for the conneciton.

The approved make & colour directed by MMCI / HPCL incharge

77 Urinal Nos 15

Supplying & fixing in position large flat urinal height 61 cms width 40 cms

including auto flushing system including electrical wiring works , brackets

spreader making a water connection including necessary piping drain

connection including C.P. waste coupling C.P. Brass Bottle Trap with

extention piece-wall flange and connection to a Drain Header etc. complete.


Supply and installing sensor controlled auto flushing system for urinal ofAutomat/Jaquar make including wiring , electrical works complete in all respects is also

included in this item

78 Stop Cock Nos 30

Supplying & fixing individual stop cock & connections for Supplying individual

manual flushing arrangement. The approved make & colour directed by MMCI /

HPCL incharge

79 Granite partition Nos 15

Supplying & fixing granite partition 20mm thick

between urinals.(Size 900x600)

80 Wash Basin Nos 24

Supplying & fixing wash basin (Rectangular) including C.I. brackets, C.P.

waste coupling, C.P. bottle trap chain & plug C.P. stop cock at supply endone long body C.P. pillar cock connecting tubing drain connection etc.

complete. The approved make & colour directed by MMCI / HPCL incharge

81 Nahani Traps Nos 24

Supplying and fixing C.I. nahani trap with stainless steel grating

including laying necessary C.I. drainage pipe of minimum

100mm dia upto the external wall everything as per requirements

of local authorities etc. complete in all respects as directed and

instructed by MMCI / HPCL Engineer Incharge.


82 Inspection Chamber up to 1.50m Depth Nos 8

Supplying and constructing brick masonry inspection chambers

with 230/345mm brick masonary in cement mortar (1:4) mix, 20mm

thick cement finish plastered internally and externally in cementmortar 1:4 mix incl. necessary excavation, foundation

concrete 1:3:6 mix 150mm thick, top cover with 100mm thick RC slab

in M20 concrete with reinforcement at 100 Kg/M3 of concrete

S.W.G. half round channels 150mm dia, concrete haunches, heavy

duty C.I. manhole cover approx. 450mm dia. and frame 16mm dia. C.I.

rod rungs at 300 mm c/c etc. complete as shown on the drawing

and/or directed and instructed by Engineer/Owner. NOTE: (Brick

work to be 230mm thick upto 1.0M depth and 345mm thick beyond

1.0M depth).

83 Gully Traps Nos 24

Supplying and fixing in position stone ware gully traps 150 x

150mm size with cover including brick masonary chamber of

clear internal size as 300mmx300mm with cement plaster finishes

42


12/19

Item


externally & internally all in cement mortar (1:4) mix including C.I.

frame and hinged cover (Heavy duty) etc. everything as per

requirements of local authorities etc. complete in all respects as

directed and instructed by MMCI / HPCL Engineer Incharge.

84 GI Pipes 40 mm dia RM 100

Supplying, laying & jointing G.I. pipes, 'C' class including all fittings and

specials such as bends, unions, elbows, couplings, tees, crosses,

reducers, enlargers, stop-ends, plugs etc. with including Supplying &

making chases in brickwirk/RCC, Supplying & making Anticorrosion

treatment to pipes consisting of a coat of Tar and covering with Bitumen

impregnated hessain cloth - Hydrotesting of pipe to ensure absence of any

leakage & making good of chase in C.M. 1:3 after fixing chicken mesh after

the completion of installation of piping.

85 GI Pipes32 mm dia RM 150

Same as item no 84 but for 25 mm dia pipe

86 GI Pipes25 mm dia RM 15








90 Shower rose Nos 9

Supplying and fixing shower rose & assembly with built in hall joint for instant

direction of changes "R-51 Jetflow" type. Approved make& colour as

directed by MMCI / HPCL Engineer Incharge.

91 Toilet Paper Holder Nos 15

Supplying and fixing in position C.P. toilet paper holder including toilet

paper roll of approved quality and make etc. complete . Approved make

& colour as directed by MMCI / HPCL Engineer Incharge.

92 Glass Mirror Nos 12

Supplying and fixing in position plate glass mirror of size 400mm x 600 mmx 5

mm thick of over 6 mm thick waterproof plywood with wooden moulding at top

and bottom including necessary hardware and synthetic enamel painting

of approved shade to moulding all complete. Approved make & colour as directed

and instructed MMCI / HPCL Engineer Incharge.

93 Soap Dispenser Nos 20

Supplying and fixing in position C.P. Brass liquid soap dispensers

of approved quality and design etc. complete as directed and

instructed by MMCI / HPCL Engineer Incharge.

94 Towel Rods Nos 22

Supplying and fixing in position C.P. M.S. Towel rods 750mm long,20mm dia. with necessary fittings of approved quality and

make etc. complete as directed and instructed by MMCI / HPCL

Engineer Incharge.

95 25 mm dia cast copper alloy stop valve Nos 5

Supplying, providing & fixing 25 mm dia cast copper alloy stop valve , chrome plated

conforming to and tested as per IS:781 of Jaguar make and approved design including

all necessary fittings etc. complete as per Technical specifications mentioned in the

tender document and as directed by the Site-in-charge.

96 20 mm dia stop valve Nos 5

Same as above but for providing 20 mm dia stop valve.

97 15 mm dia stop valve Nos 5

Same as above but for providing 15 mm dia stop valve.98 12 mm dia bib taps Nos 20

Supplying, providing & fixing cast copper alloy screwed down 12 mm dia. Long stem

type bib taps chrome plated conforming to and tested as per IS:781 & of Jaguar make

with all necessary fittings etc. complete as per technical specifications and as directed

by the Site-in-charge.

99 15 mm dia pillar cocks Nos 5

42


13/19

Item


Supplying, providing & fixing cast copper alloy screwed down 15 mm dia. chrome

plated Pillar cock conforming to and tested as per IS:781 & of Jaguar make with all

necessary fittings etc. Complete as per technical specifications and as directed by the

Site-in-charge.

100 Ball Cock 12 mm dia Nos 40

Supplying and fixing brass body heavy duty ball cock with PVC

float including necessary fittings & fixtures as instructed & directed by

MMCI / HPCL Engineer Incharge.

101 HDPE Pipe 100mm Dia RM 215

42


14/19

Item


Supplying and laying of 100mm dia HDPE pipes of heavy duty & first quality as

approved by MMCI/HPCL Engineer Incharge.Scope include supply & laying of all the

necessary pipe bends,socket/collars required for joining the pipes etc. complete as

directed by MMCI/HPCL Engineer Incharge

102 HDPE Pipe 75mm Dia RM 550

Same as item 101 above but for 75mm dia

103 PVC Pipe 100 mm Dia RM 5

Supplying, delivering and laying PVC pipe (6 kg/cm2 quality) of

approved make for Sewage disposal including bends, offsets, 'Y'-s /

Tees etc., jointing with solvent cement etc all necessary puddle flanges

for joints of PVC and manholes accessories confirming to IS-4985

testing, rectification, filling partly with sand including required excavation

and backfilling the trench etc. everything as per local authorities etc.

complete in all respects as directed and instructed. (Earthwork

excavation and filling the sand will be paid separately under relevant

sections & Items)

104 PVC Pipe 150 mm Dia RM 15

Same as item 103 above but for 150 mm dia

105 Sintex or equivalent water tanks 1000 litre Nos 1

Supplying and erecting ready made storage tanks of 'Sintex' orapproved manufacturer and required size including connecting

necessary supply lines, delivery lines, wash water line and with

manhole cover at top of not less than 450mm clear dia, with locking

arrangement complete as per drawing and as directed and instructed

by MMCI / HPCL Engineer Incharge.


Same as item 105 above but for 2000 litre


Same as item 105 above but for 5000 litre

108 Soak pit Nos 4

Supplying, providing & constructing soak pit of size as per drawing, including excavation& filling the pit with gravel and brick bats of maximum size 80 mm ; the brick masonry

wall shall be as per the details given on the drawing complete as per Technical

specifications mentioned in the tender document and as directed by the Site-in-charge.

109 Precast septic tank -50 users Nos 2

Providing & fixing septic tank suitable for 50 users of Indian Hume Pipe Co. or

construction of septic tank as per drawings / specifications (the rates shall include

excavation, placing in position all necessary connections and accessories, testing the

joints, backfilling etc. complete and as directed.

110 Sink Nos 5

Providing and fixing stainless steel kitchen sink (600 x 450 x 250 mm

deep approx size) of Hindustan Twyford make or any other equivalent

approved make with stopcock, pillar cock, waste couplings, CP bottle

trap, rubber plug and CP brass chain CI brackets, drainage connectionwater supply with drain board and plumbing installations up to external

wall etc complete as directed and instructed by MMCI / HPCL

Engineer incharge

111 Stainless steel hand rail RM 165

Supplying & fixing stainless steel hand railing of grade 304 (16 gauge thick

sections) with glossy finish consisting of 38 NB or nearest size vertical posts 900

heigh at maximum spacing of 1000 c/c with suitable cups at bottom & top rail of

38 NB or nearest size & intermediate rails of 20 NB or nearest size etc complete at

alll levels including bending to required profile. Tungsten inert gas welding & alll

required accessories & labour etc complete.

112 Door Closure Nos 34

Supplying & fixing Godraj make or equivalent confirming to IS : 3564marked aluminium extruded section body tubular type universal hydraulic door

closure with double speed adjustment with necessary accessories & screws

42


15/19

Item


etc.complete.

113 Floor spring Nos 15

Providing and fixing double action Everite/Dorma or equivalent floor spring

(Hydraulically operated) as per IS 6315 latest revision for entrance door with all fixturers

and accessories with foundation box, main body and half cover and top cover made of

aluminium alloy pressed dye casting 2mm minimum thick, gun metal piston layer and

cast brass top, center pivot etc. complete including connecting door shutter to hinges,

etc. complete including charges for making good the floors etc.

114 Roof Sheeting M2 12900

Supplying, transporting & stacking , fixing in position Zincalume clip on OR

equivalent sheeting as follow with accessories such as Fasteners & Foam filler

detailed as under all complete as per instructions of MMCI/HPCL Engineer-in-Charge

FASTNERS

Mechanically galvanised self drilling high grip screws 12-14 X55 with integral washers.

EPDM seals and 10-12X25 screws at side laps.( not measured for payment)

FOAM FILLER:

Polyethylene foam filler cut to suit profile at all ends to ensure air tightness.

SHEETING:

a) rackdeck KLIPPON AZ 150 SMP colour coated ( in approved colour) or equivalent

profile, suitable for purlin spacing upto 1.8 m c/c.

b) 0.50 mm thick without coating with 0.55 mm total coat thickness.

c) 550 MPA yield stress cold Rolled Steel ASTM A446 Grade E)

d) Hot dip metallic coating confirming to AZ150 of AS 1397 with hot dip metallic

coating of 55% Al and 45% Zn alloy having total coating mass of min 150 gms/m2

inclusive of both sides.

e) Measurement is installed area ( net area overlap will not be counted)

f) All overlaps sealed with neutral cured silicon sealants.

115 Roof Accessories M2 1520

Supplying and fixing Zincalume accessories like cappings, flashings, ridges etc.

compatible to sheeting as per item code 114 but in plain sheet including all neutral

coloured silicone rubber sealants, fasteners, washers, bolts, nuts and any other

specials etc. complete as directed & instructed by MMCI / HPCL Engineer In

charge

116 Translucent sheet M2 700

Supplying and fixing Polycarbonate sheet roofing compatible with Zincalume sheet

with all accessories,washer,bolts, nuts as necessary for f ixing complete as

directed & instructed by MMCI / HPCL Engineer

117 MS Fan Hooks Nos 70

Supplying and fixing in position fan hooks of M.S. 16mm dia bar

and 450mm long in concrete slab as shown in drg. and as

directed including painting with one coat of primer and two coats of

synthetic enamel as directed & instructed by MMCI / HPCL

Engineer Incharge.

118 450 mm dia sweep Exhuast fan Nos 22

Supplying & fixing of 450 mm sweep Exhuast fan of Crompton Greaves or its

equivalent make approved by HPCL. Scope includes supplying & Wiring with 3 runs of

3/0.29 PVC insulated copper conductor in suitable 2 MM thick PVC pipe in concealed

manner and in 16 SWG MS conduit for the wiring above the finished surface, having

5A/6A switch control on suitable MS cover with box including 3/036 PVC insulated

copper conductor for light, fan points etc. as required. Work includes all wiring

accessories complete as reqd & include cost of switches of Anchor ROMA make ,ceiling roses, extension rods etc. , cost of digging chases & refilling the same with CM

1:4 & making the wall good as required.

119 Switch Sockets:

5/16A Switch socket point( Regular Switch Socket ) Nos 40

42


16/19

Item


Supply and fixing of 3 - pin, 250V, 5/16A switch and socket combined with indicator

and fuse on suitable MS cover with box in concealed manner. Scope includes supplying

and run of 2.5 Sq.mm PVC insulated copper conductor in suitable 2 mm thk. PVC pipe

in concealed manner and in 2mm MS conduit for the wiring above the finished surface

from power plug to power DB etc. complete as required.

120 16/32A Switch socket Nos 20

Supply and fixing of TPN, 415V, 16/32A switch and socket combined with indicator and

fuse on suitable MS cover with box in concealed manner. Scope includes supplying andrun of 4 Sq.mm PVC insulated copper conductor in suitable 2 mm thk. PVC pipe in

concealed manner and in 2 mm MS conduit for the wiring above the finished surface

from power plug to power DB etc. complete as required.

121 20A A.C. Points Nos 20

Same as above item but for supplying & Supplying 20A AC points wherever necessary

as directed by the Site-in-charge.

Lighting & Power Distribution Boards:

122 100A TPN DB with MCCB+ELCB Nos 2

Supply, Installation, Testing and Commissioning of Indoor 3-ph PDB comprising of 1

No. 100 A TPN MCB + ELCB as incomer feeders, 13 Nos., 20 A SPN MCBs as

outgoing feeders. dust & vermin proof (IP-42 protection). It shall be fabricated from 16

SWG CRCA sheet steel enclosure & shall be of compartmentalised type (incomer,

outgoings & termination compartments). LDBs shall be provided with 100 A tinned

copper phase and neutral bars and earth bar of suitable size with earth connection

brought to outside. LDBS shall be suitable for bottom cable entries. Knock outs shall be

provided to receive incoming & outgoing cables. DBS shall be supplied with DIN-

channel, neutral link & busbars. The bus bars shall be of Electrical grade aluminium &

shall be supported rigidly to withstand fault level of 16KA for 1 sec. DBs shall undergo a

treatment of degassing. pickling and two coats of primer before painting with two coats

of antocorrosive enamel paint

123 63A TPN DB with MCB+ELCB Nos 3

Supply, Installation, Testing and Commissioning of Indoor LDB comprising of 1 No. 63

A TPN MCB + ELCB as incomer feeders, 16 Nos. 10A SPN MCBs as outgoing

feeders. dust & vermin proof (IP-42 protection). It shall be fabricated from 16 SWG

CRCA sheet steel enclosure & shall be of compartmentalised type (incomer, outgoings

& termination compartments). LDBs shall be provided with 100 A tinned copper phaseand neutral bars and earth bar of suitable size with earth connection brought to outside.

LDBS shall be suitable for bottom cable entries. Knock outs shall be provided to receive

incoming & outgoing cables. DBS shall be supplied with DIN-channel, neutra link &

busbars. The bus bars shall be of Electrical grade aluminium & shall be supported

rigidly to withstand fault level of 16KA for 1 sec. DBs shall undergo a treatment of

degassing. pickling and two coats of primer before painting with two coats of

anticorrosive enamel paint

124 32A TPN DB with MCB+ELCB Nos 7

Same as above but for Indoor 3- Phase LDB comprising of 1No.32A TPN MCB + ELCB

as incomer feeder. 8 Nos. 10A SPN MCBs as outgoing feeders.

125 Tube light fittings -- BJSM 02 Nos 90

Supplying & fixing of commercial decorative type tube light fittings of Bajaj (Model

no:BJSM 02 236)/Philips or its equivalent make approved by HPCL. Scope includes

supplying & Wiring with 3 runs of 3/0.29 PVC insulated copper conductor in suitable 2MM thick PVC pipe in concealed manner and in 16 SWG MS conduit for the wiring

above the finished surface, having 5A/6A switch control on suitable MS cover with box

including 3/036 PVC insulated copper conductor for light, fan points etc. as required.

Work includes all wiring accessories complete as reqd & include cost of switches of

Anchor ROMA make, ceiling roses etc. , cost of digging chases & refilling the same with

CM 1:4 & making the wall good as required

Note: The distance from the switch board to tube light fitting shall be approx. 20 m..

126 Tube light fittings -- BJSM 14 Nos 10

Same as above but for supplying & fixing tube light fittings of Bajaj make BJSM 140 or

its equivalent model of Philips/ Crompton make approved by HPCL.

127 Tube light -Industrial type Nos 100

42


17/19

Item


Supplying & fixing of Industrial type tube light fittings of Bajaj (Model no:BJI 240

FG)/Philips or its equivalent make approved by HPCL. Scope includes supplying &

Wiring with 3 runs of 3/0.29 PVC insulated copper conductor in suitable 2 MM thick

PVC pipe in concealed manner and in 16 SWG MS conduit for the wiring above the

finished surface, having 5A/6A switch control on suitable MS cover with box including

3/036 PVC insulated copper conductor for light, fan points etc. as required. Work

includes all wiring accessories complete as reqd & include cost of switches of Anchor

ROMA make, ceiling roses etc. , cost of digging chases & refilling the same with CM 1:4

& making the wall good as required.

128 Philips TBS-305/218 M5 HPF-2X1 Nos 10

2X18 W Mirror optic recessed mounting, Flourescent Tube light fitting, PHILIPS TBS-

305/218 M5 HPF or equivalent model of Bajaj/crompton Make

129 Philips TBS-305/418 C6 HPF-4X1 Nos 10

4X18 W Mirror Optic , High efficiency, Recessed Mounting Flourescent tubelight Fitting,

PHILIPS TBS-305/418 MI HPF or equivalent model of Bajaj/crompton Make

130 PHILLIPS FCS 31/211-2 X 11 W S Nos 10

2 X 11 W Surface mounted, low profile, Mirror optic fitting FOR PL-S Lamp, Philips FCS

31/211 or equivalent model of Bajaj/crompton Make

131 Philips FBH 145-1X 10 W Recess Nos 10

1X 10 W Recessed Downlight, Wall washer type, PL-C Lamp, Philips FBH 145 or

equivalent model of Bajaj/crompton Make

132 Philips FDN 620/01-1X9 W Low d Nos 5

1X9 W Low Depth, Recessed Downlight, Wall waher type, PL-S Lamp, Philips FDN

620/01 or equivalent model of Bajaj/crompton Make

133 Philips FDN 622/01-1X 9 W Rec Nos 5

1X 9 W Reecessed Downlight, FOR PL-S Lamp, Philips FDN 622/01 or equivalent

model of Bajaj/crompton Make

134 1200 mm dia Ceiling fan Nos 30

Supplying & fixing of 1200 mm sweep Ceiling fan of Crompton Greaves or its

equivalent make approved by HPCL. Scope includes supplying & Wiring with 3 runs of

3/0.29 PVC insulated copper conductor in suitable 2 MM thick PVC pipe in concealed

manner and in 16 SWG MS conduit for the wiring above the finished surface, having

5A/6A switch control on suitable MS cover with box including 3/036 PVC insulated

copper conductor for light, fan points etc. as required. Work includes all wiring

accessories complete as reqd & include cost of switches of Anchor ROMA make ,

ceiling roses, extension rods etc. , cost of digging chases & refilling the same with CM1:4 & making the wall good as required.

135 Telephone

2 Pair telephone wiring as mentioned below RM 500

Supply & laying of 2 pairs of 0.5 mm dia screened & shielded telephone wire in 20 mm

dia PVC conduit partly/fully concealed in types of walls, floor etc. complete with all

accessories, wiring terminators, connected civil works, rough plastering etc including

supply of 16 SWG GI fish wire conduit and accessories

136 RJ 11 Telephone connectors Nos 20

Supply & fixing of modular type telephone connectors in suitable size PVC box

concealed to wall including all civil works.

137 20 pair telephone junction box Nos 5

Supply & fixing of 20 pair telephone tag block with crone connectors housed in suitable

MS junction box.

138 Fire Alaram System2 Pair fire alarm wiring as mentioned below RM 500

Supply & laying of 2 pairs of 2.5 mm core dia Un armoured FRLS Cable in 25 mm dia

MS conduit partly/fully concealed in types of ceiling, walls, floor etc. complete with all



139 Back Box / Pull box with 4 terminals Nos 50

Supply & fixing of 4 terminal MS back box /pull box.

140 TAS LAN

CAT 6, 4 pair twisted pair computer cable for TAS LAN RM 200

Supply & laying of CAT 6, 4 pair twisted computer cable screened and shielded in 20/25

mm dia PVC conduit partly/fully concealed in types of walls, floor etc. complete with all



141 RJ 45 Computer Connectors Nos 15

Supply & fixing of modular type of RJ 45 computer connectors in suitable size PVC box


142 CCTV

Co-axial braided cable RM 50

42


18/19

Item


Supply & laying of co axial, braided cable in 20/25 mm dia PVC conduit partly/fully

concealed in types of walls, floor etc. complete with all accessories, wiring terminators,

connected civil works, rough plastering etc including supply of 16 SWG GI fish wire

conduit and accessories

143 BNC CCTV Connectors Nos 3



144 MIS LAN

CAT 6, 4 pair twisted pair computer cable for MIS LAN RM 600

Supply & laying of CAT 6, 4 pair twisted computer cable screened and shielded in 20/25

mm dia PVC conduit partly/fully concealed in types of walls, floor etc. complete with all



145 RJ 45 Computer Connectors Nos 15



146 150 mm dia GI Pipes for sleeves in trenches RM 15

Providing, supplying and laying 150 dia. G.I pipes below grade slabs/embedded

in foundations, for laying electrical/instrument cables.Etc complete as per drawings

& instructions of MMCI/HPCL Engineer in charge.

147 100 mm dia GI Pipes for sleeves in trenches RM 15

same as item no 146 but with 100 mm dia G.I pipe

148 80 mm dia GI Pipes for sleeves in trenches RM 10same as item no 146 but with 80 mm dia G.I pipe

149 SHALITEX BOARD EXPANSION JOINT M2 20

Supplying and fixing in position 25 mm thick SHALITEX BOARD EXPANSION joint for

columns and between walls at all heights. SHALITEX board shall be manufactured by

M/s SHALIMAR TAR products or equivalent as per their standard specifications.

42


19/19

Item


150 POLYSULPHIDE SEALANT RM 15

Supplying and applying in position two part exterior grade polysulphide sealant on the

expansion joint. The sealant shall be of PIDISEAL PS 41G of M/s Pedilite Industries or

equivalent. The sealant shall be applied all as per manufacturer's specifications and

recommendations. Appropriate primer, masking tapes etc should be applied. The

sealant shall be maximum 50 mm in thickness and of maximum depth of 25 mm.

The rate shall be inclusive of providing and fixing breaker rod as per detail architectural

drawings.

151 GYPSUM BOARD FALSE CEILING M2 130

Supplying and fixing SUSPENDED FALSE CEILING at any level which includes

providing and fixing GI perimeter channels of size 0.55 mm thick having one flange of

20 mm and another flange of 30 mm and a web of 27 mm alongwith perimeter of ceiling,

screw fixed to brickwall / partition. Then suspending GI intermediate channels of size 45

mm 0.9mm thk.. with two flanges of 15 mm each from the soffit at 1220 mm centers

with ceiling angle of width 25mm x 10 mm x 0.55 mm thk.. Fixed to soffit with GI cleat

and dash fasteners. Ceiling section of 0.55 mm thk.. having knurled web of 51.5 mm

and 2 flanges of 26 mm each with lips of 10.5 mm are then fixed to the intermediate

channel with the help of connecting clips and in direction perpendicular to the

intermediate channel at 457 mm centers. 12.5 mm tapered edge Gypboard (conforming

to IS-2095-1982) is then screw fixed to ceiling section with 25 mm drywall screws at 230mm centers.

Finally square and tapered edges of the boards are to be painted and finished so as

to have a flush look which includes fill ing and finishing with jointing compound and

paper tape and two coats of primer suitable for GYPBOARD. (as per recommended

practices of INDIA GYPSUM or equivalent)

PAINT FINISH : -

Providing and applying 2 coats of PLASTIC EMULSION paint of approved

manufacturers, on the GYPBOARD surface including necessary surface preparation

such as scrapping, brushing, cleaning etc. all complete.

Please Note :

(a) The False ceiling contractor shall provide suspension system / necessary framing for

light fixtures, collars for return air grills as well as A.C. diffusers.

(b) Measurements shall be wall to wall without any deductions for Light Fixtures,diffusers, columns etc.

152 FALSE FLOORING M2 40

Supply and installation of UNITEC JEC or equivalent make raised flooring type FS-1200-

30G steel panel 600x600x30mm along with bolted stringer of height(500-600 mm) with

Antistatic laminate top as per drawing and manufacturer's specification complete.

153 Precast Slab M2 100

Supplying & fixing precast RCC Slab of 75 mm thk. in M20 Grade in drain,pit,trench

covers including shuttering,finishing smooth with 6 mm thick cement plaster (1:3)

on exposed surface complete including transport at site & placing in position all

complete including reinforcement fixing (R/F should be pain separate item) as per

drawing and specification

154 150 Dia Hume Pipe RM 40Supplying & Laying cement concrete pipes of NP-2 Class of 150 mm dia in proper line

level & slope including supply & fixing of collars in cement mortars 1: 2 with curing

complete as per specification & drawing.

155 300 Dia Hume Pipe RM 40

Supplying & Laying cement concrete pipes of NP-2 Class of 300 mm dia in proper line

level & slope including supply & fixing of collars in cement mortars 1: 2 with curing

complete as per specification & drawing.

156 Point wiring for light fixture Nos 100

Point wiring including circuit wiring using 3/0.29 PVC insulated copper wire of approved

make, in existing PVC conduit for lighting fixtures. Job to be carried out through existing

conduits, existing wired conduits etc of various buildings inside HPCL premises. The

payment is on point basis for all lengths. The rates shall include supply of modular type

switches, sockets, regulators, metal boxes, all accessories required for completion of

the point, cost of digging chases & refilling the same with CM 1:4 and making good thewall back to original condition ; exclusive of fixing charges of DBs, light fittings, fan

fittings etc.

BOQ for Civil-Bhatinda

Documents

Transcript of BOQ for Civil-Bhatinda