Civil-Boq FINAL-.xlsx

King Abdullah Bin Abdulaziz

Technical & Vocational Training Center

BOQ Ground, First, Second and Third Floors works

King Abdullah Bin Abdulaziz Technical Vocational Training Center

Civil Works

Bill No. 1 Excavation and Earth Works

Item No

Description Unit QTY Price/

Unit Total

The Contractor shall when pricing the rates of this bill, take into consideration including and allow for the cost or expenses of all requirements stipulated in the preambles, drawings, and technical specifications. The words engineer below means owner's engineer. The rate include the following:

The contractor has to supply a Mesh Survey plan 5mX5m for the site from approved engineering surveyor before and after the works for quantities measurements .

The Contractor should present a soil investigation report from an approved laboratory as per engineering association equipments and standards on his own expenses.

Excavation and backfilling for Working Space will not be measured .

In case and after the soil investigation report is done it was required to do more excavations, all excavations work will be carried over the bid unit price, the Contractor has no right for any kind of claims or any unit price change .

1.1

Cut in any kind of soil, concrete or stone walls to reduce level for site leveling and to reach the desired level(Below basecoarse layer) according to drawings and site instructions .The price should include using and laying the approved fill material from site and or from outsite to reduce level and all test required to use the approved cut material for filling and watering ,compacting 100% each layer 20 cm and removing the unapproved excavated materials from the site to an approved dump location.

m3 5800

1.2

Ditto but excavation for footings , ground beams, neck wall and tie beams, the price should include soil Investigation total boreholes depth 36m after site leveling from approval laboratory and as shown on drawings and specifications and engineer instructions.

m3 400

1.3

Supply and Lay selected & approved base coarse filling First class at 20cm layer to the required level ,watering and compacting 100% and where directed by the Engineer.

m2 400

Total of Bill No. 1

1 of 25


Civil Works

Item No Description Unit QTY Price / Unit Total

2 Concrete Works

The contractor shall, when pricing the rates of this bill, take into consideration including and allow for the costs or expenses of all requirements stipulated in the preambles, drawings and technical specification of the tender.

Each concrete pouring on site will be tested, pouring less than 6m3 will be tested, pouring more than 6m3 will also be tested on 6m3 portions i.e. each concrete truck on site will be tested, all done by an approved testing institute on contractors expense

The price should include cleaning all the foundation excavations, checking the sizes according to drawings, resizing if needed, cleaning, and installing wooden frame to marked the footings as instructed and approved by the site engineer

In case and after the soil investigation report is done, concrete quantities may vary,any Additional or less in bid quantities will be carried over the bid unit price, the Contractor has no right for any kind of claims or any unit price change .

2.1 PLAIN IN-SITU CONCRETE B200[200 Kg / CM2]

Supply & install Concrete B200 of 28 days cube crushing strength 200kg/cm2. Price shall include cleaning, compaction, shuttering and making good of ground surface before casting of concrete. Price shall include all nails, forms and equipments needed.

2.1.1- Blinding under footing, ground beams and raft foundation

m3 40

Bill No. 2 Concrete Works

2 of 25


Civil Works



2.2 REINFORCED IN-SITU / READY MIXED CONCRETE

B300/ 300 Kg / CM2]

Supply & install concrete B300 of 28 days cube crushing strength 300kg/cm2. Price shall include the following:1. Cleaning and making good of surfaces before casting of concrete2. Steel reinforcement workmanship as per drawings.3. Form-work of any type or shape .4. Any materials such as nails, wires , 6mm steel for shuttering or any other material or workmanship needed for a best completion of the works .5. Installation of 2 cm thick. high density polystyrene on expansion joints.6. All steel reinforcement of any diameter and shape of high yield stress steel.7. Cube test 10x10x10cm and slump test before pouring any concrete on site, and vibration the concrete during casting . 8. Supply and install Polystyrene Blocks for Ribbed slabs as per Drawings and Structural notes. 9- isolation all buried parts using approved butimunies layer (hot or cold ) as per site engineer instructions and approval.

The measurement for slabs from the middle of the walls , and include all drop and inverted beams and any part casted with slab, also deduction any opining in the slab(engineering measurements ) .

2.2.1Foundation of any shape, depth and size including column foundations, ground beams and strip footings , when pricing the contractor has to take the followings

A- Check and report to the site engineer the situation of the excavation by an approved surveyorB- Clean the foundations excavations, and making good of any excavation if needed

m3 135

C- Resize the excavations to suit the design if there was any mistake in the excavation processD- Lay a wooden Works Frame Reference around the building to be referenced by an approved surveyor and approved by the site engineer

2.2.2

Tie Beams and Neck wall of any shape, depth and size including column foundations, and tie beams, when pricing the contractor has to take the followings into considerationA- Check and report to the site engineer the situation of the excavation by an approved surveyorB- Clean the foundations excavations, and making good of any excavation if needed

m3 75

C- Resize the excavations to suit the design if there was any mistake in the excavation processD- Lay a wooden Works Frame Reference around the building to be referenced by an approved surveyor and approved by the site engineer

3 of 25


Technical Vocational Training Center

Civil Works



2.2.3

For concrete columns and column necks B-300,

maximum size of aggregate 20mm as shown on

drawings.

m3 120

2.2.4Ditto but columns concrete B-400 as shown on

drawings.m3 30

2.2.5

For bearing walls, bearing walls necks, retaining walls

and bracing beams where needed as per site engineer

instructions the price include the steel and concrete

columns and formwork inside the bearing wall and as

shown on drawings .

m3 220

2.2.6

For 12cm Thick slab on grade with Ф10mm 20x20cm

steel mesh reinforcement. The price includes 500

micron thick polyethylene membrane.

m2 175

2.2.7

Ditto but fair face for slab on grade(Parking Area) using

machine helicopter, the price include expansion joint

thick 2cm each block 4X4m and filling the joint with

rode diameter 2cm and sika flex depth 2cm and

instructed by the engineer .

m2 235

2.2.8.aFor Reinforced Ribbed slab Thickness 36cm as shown

on drawings and instructed by the site engineer, m2 1360

2.2.9For well reinforced Solid slab Thickness 25cm as

shown on drawings and instructed by the site engineerm2 35

2.2.10

For stairs ,flights and landings of different

thicknesses,Rate will includes all connections

scaffoldings and steel reinforcement as shown on

drawings (measurements will be for the horizontal

projection of flight and stairs ).

m2 100

2.2.11

Supply and install concrete B-200 for inclined 1.0% roof

screed , the minimum thick 5 cm at rain pipe, marks

should be approved prior to commencement,

mechanically finish all as instructed by the site engineer

m2 360

Total of Bill No. 2

4 of 25


Civil Works

Item No

Description Unit QTY Price / Unit Total

3 Stone Works

3.1 STONE BUILDING AND POINTING

The contractor shall, when pricing the rates of this bill, take into consideration including and allow for the costs and expenses of all requirements stipulated in the preambles, drawings and technical specification of the contract. The price includes the following:

All stone should be from Hebron area dark colour class A-A, بند ارضي, with the following specifications:

- Absorption by weight should not exceed 0.9% using ASTM test method C97

- Density (Kg/m3) should not be less than 2700Kg/m3 using ATSM test method C97

- Compressive strength should not be less than 56MPa using ATSM test method C170

- Modulus of rupture should not be less than 6.9MPa using ATSM test method C99

- Abrasion resistance (hardness) should not be less than 10 using ATSM test method C241 - stone should be clear, free from all veins, cracks and salt holes from both sides

1. Steel anchors as specified.2. Flush pointing works composed of white cement and sand (1: 2) with approved additives for better workability, tightness and water proofing. 3. Ф8mm 20X20cm steel mesh reinforcement to be used for all stone concrete backing.4. Stone built shall be measured only " Net Measurements "

Bill No. 3 Stone works

5 of 25


Civil Works

Item No



5. Each building stone must have at least two galvanized anchors from the top and to be fixed to the 3mm steel mesh.6. Acceptance of delivered stones should be carried by comparing every stone delivered on the truck to the sample built on site. All stones will be picked up and chosen by a specialist person (dresser) paid by the Contractor before using the stone.7. Rate includes any kind of stone dressing.8. Copping stones to be Mutabbeh finish for the horizontal surface and Taltish finish for the vertical sides. 9- Price should include supply and install extruded polystyrene 30 mm thick as per drawings and site engineer instructions and approval .

3.1.1

Supply and install 5 cm thick 25cm height TALTEESH stone courses the price including all special pieces i.e. jams, lintels, sills and stone corners (at least 15cm deep), as shown on drawings. The price includes B200 concrete backing with varies thickness according to drawings, anchors and steel reinforcement,glans plastering layer on concrete backing and extruded polystyrene sheet of 30 mm thick all as shown on drawings, instructed and approved by the site engineer

m2 730

3.1.2Supply and build 5cm Thick stone copping width in any location as shown on drawings

m2 60

3.2.3Supply and build 5cm Thick stone sills width 15cm for windows to be build from outside as shown on drawings

m.r. 80

6 of 25


Civil Works

Item No



3.2 Stone Cladding

Supply, install stones cladding of excellent quality grade A-A " بند ارضي " with different thickness dressed Mulatash free from cracks. Rate for stone cladding shall include for:

All stone should be from Hebron Area dark colour class A-A, بند ارضي, with the following specifications:

- Absorption by weight should not exceed 0.9% using ASTM test method C97 - Density (Kg/m3) should not be less than 2700Kg/m3 using ATSM test method C97 - Compressive strength should not be less than 56MPa using ATSM test method C170 - Modulus of rupture should not be less than 6.9MPa using ATSM test method C99 - Abrasion resistance (hardness) should not be less than 10 using ATSM test method C241 - stone should be clear, free from all veins, cracks and salt holes from both sides

1. Work for all classification in any location.2. Stone shall have a minimum thickness of 5cm after dressing with a rough back preferably.3. Stone built shall be measured only " Net Measurements "4. Stone sills and lintels of any kind shall be measured within the stone building and not separately

7 of 25


Civil Works

Item No



5. Corner and jambs stone of any kind shall be measured within the stone building and not separately6. Key stone and any other particular stone shall be measured within the stone building and not separately7. Price shall include concrete backing and Ф6 mm @ 20cm welded steel mesh and steel reinforcement for lintel beams.8. Stones with quality grade A-A (بند ارضي) shall be used only.9. Acceptance of delivered stones should be carried by comparing every stone delivered on the truck to the sample built on site. All stones will be picked up and chosen by a specialist person (dresser) paid by the owner before using the stone.10. Flush pointing works composed of white cement and sand (1: 2) with approved additives for better workability, tightness and water proofing.

3.2.1

Supply and install 5 cm thick 25cm high, stoneTaltish courses of first quality the price (دقة ناعمة بدون زملة)including all special pieces i .e. jams and lintels and stone corners, of depth not less than 25cm. The price includes 7-10cm thick B200 concrete backing,steel mesh and galvanized wire to tie the stone to the steel mesh as shown on drawings.The rate includes for walls and around columns and all special pieces

m2 730

Total of Bill No. 3

8 of 25


Civil Works Bill No. 4 Block Works

Item No


4 BLOCK WORK BUILDING

The contractor shall, when pricing the rates of thisbill, take into consideration including and allow forthe costs or expenses of all requirementsstipulated in the preambles, drawings andtechnical specification of the contract.

The price include lintel concrete beam andscaffolding above all blocks with height 20cm withsteel 4Ф12mm and stirrups Ф8mm/20cm

For the double Block wall Price should includesupply and install expanded polystyrene sheetthick 3 cm between walls as per drawings.

Precast Concrete hollow nonloading bearingblocks built in cement sand mortar (1:3) mix asspecified. All opening to be closed with blocks aremeasured in m2 of correspondent thickness.

Engineering measurement all openings must bededuction . The measurement engineeringdeduction all opening

4.1 7 cm thick hollow blocks. m2 450



Total of Bill No. 4

9 of 25


Civil Works

Bill No. 5 Plastering Works

Item No


WALL AND CEILING PLASTERING

5 Internal Plaster

The contractor shall, when pricing the rates of this bill, take into consideration including and allow for the costs or expenses of all requirements stipulated in the preambles, drawings and technical specification of the contract.

Prepare surfaces, apply a rendering coat (رشة مسمار),apply in two coats of rough and fine finish withordinary Portland cement , sand and lime asspecified. The price includes angle beads andmovement beads.

The measurement engineering , deduction allopening .

5.1

On walls and ceiling 13mm thick plaster includingpatching works for any mechanical, electrical or civilworks. Price should include supply and install steel wiremesh 200 mm wide , cloth mesh and galvanized steelor aluminum angel 2 m length where required, All asper site engineer instructions .

m2 4800

5.2 Ditto but for external plastering mixing with Begebond. m2 120

Total of Bill No. 5

10 of 25



Civil Works

Item

NoDescription Unit QTY Price / Unit Total

6 Tiling Works

The Contractor shall when pricing the rates of this

bill, take into consideration including and allow for

the cost or expenses of all requirements stipulated

in the preambles, drawings, and technical

specifications.

Unit rate shall includes all designs and cutting as

per drawings with no allowance for wasted tiles.

Net engineering measurements on site for square

meter will be considered.

Unit rates for tiling works shall include the

completion of works according to all details shown

on drawings. The rate includes the pointing or

grouting as specified, the crystal polish of terrazzo

tiles.

Tiling should be done using WHITE CEMENT only,

even if not specified in the item

6.1 Ceramic or Porcelain Tiles

6.1.1

Supply and Install Ceramic or porcelain for floor & wall

Tiles in patterns first choice and free from all defects.

with 5mm spacing and to be pointing with a water

resistant grout like Mapei and cleaning on site. Price

to include the mortar (White Cement) (1:3). The type,

colour and size shall be approved by Engineer the price

include, transportation, tiles cutting galvanized angle for

corners and as shown on drawings

m2 430

6.2 Terrazzo Tiles

Supply and install the following class A terrazzo local

tiles size30X30X3cm Chips number 4 with a pattern

as per drawings. All bedded in , or backed with white

cement and sand mortar (1:3) . The price shall

include the supply and spreading of a layer of sand and

Portland cement dry mixture under tiles and

grouting with white cement thick 3mm (grouting colour

will be given by owner) the price also include supply

and install skirting the same as terrazzo tiles high 7cm

6.2.1 To Floors m2 1100

Bill No. 6 Flooring

11 of 25


Civil Works

Item No


Bill No. 6 Flooring

6.3 Stone Tiling1- All as per stone samples on site for colour, quality and shape.2- All stone tiles shall be free from cracks with quality grade A-A (بند ارضي) .3- Rates for tiles shall include for straight and curved cutting, waste, grouting and pointing to execute the works to the satisfaction of the Engineer.4- All stone tiles will be picked up and chosen by a specialist person (dresser) paid by the owner before using the stone. - Absorption by weight should not exceed 0.9% using ASTM test method C97 - Density (Kg/m3) should not be less than 2700Kg/m3 using ATSM test method C97 - Compressive strength should not be less than 56MPa using ATSM test method C170 - Modulus of rupture should not be less than 6.9MPa using ATSM test method C99 - Abrasion resistance (hardness) should not be less than 10 using ATSM test method C241 - stone should be clear, free from all veins, cracks and salt holes from both sides

6.3.1

Supply and install approved natural stone polished for stair flight thick 3cm for tread and 2cm for riser the price include cement mortar under the stone and filling cement:sand 1:1 below the tiles the price include stone panels and skirting for water resist and as shown on drawings .

m.r. 210

6.3.2

Supply and install approved natural stone polished for stair landing thick 3cm size 60x30 the price include cement mortar under the stone and filling cement:sand 1:1 below the tiles the price include skirting30x7 thick 1cm and grouting with white cement and as shown on drawings .

m2 50

6.3.3 Ditto but stone door thresholds, 3cm thick m2 10

6.3.4

Supply and install approved natural stone tiles for top roof thick 5cm size 60x30 the price include cement mortar under the stone and filling cement:sand 1:1 below the tiles the price include skirting30x7 thick 1cm and grouting with white cement and as shown on drawings .

m2 60

Total of Bill No. 6

12 of 25


Civil Works

Bill No. 7 Water Proofing

Item No


7 Water Proofing


7.1

Supply and install 4 mm thick layers for top roof and agricultural path of modified bituminous membrane like Pazkar SBS 5/250 laid above two primer coats of GS474 at a rate of .25 kg /m2 or equivalent approved by the engineer on a clean surface of the roof tiling and around the parapets. The price includes supply and install sealant cover at groove" Sikaflex-pro 2HP or equivalent" . The price includes also supply and install 15*15cm angle fillet as shown in the drawings and painting the joints with "Silver PAZ". The application should be carried out in conformity with the manufacturers’ specifications and using propane torch welding only. The measurement horizontal dimension .

m2 550

7.2

Supply and install 4 mm thick layers for walls under natural ground of modified bituminous membrane like Pazkar SBS 5/250 laid above two primer coats of GS474 at a rate of .25 kg /m2 or equivalent approved by the engineer the price include make glanz layer cement:sand (1:1) on concrete wall on a clean surface and the price include also protection the insulation layer with polystyrene sheet 2cm and supply and install block 7cm and as shown on drawings . The measurement horizontal dimension .

m2 500

7.3

Supply and apply two coat of Sika Top Seal 107 or equivalent on a clean surface for the wet areas. The price includes 5*5cm angle fillet with smooth sand cement mortar (1:3) surface layer before applying the water proofing materials. The application should be carried out according to details and in conformity with the manufacturers’ specifications price include testing as instructed by the site engineer. The measurement horizontal dimension .

m2 260

Total of Bill No. 7

13 of 25


Civil Works

Item No Description Unit QTY Price / Unit Total 8 Metal Works


The rate for steel works includes the following:

A. The submittal of shop drawings for the satisfaction of the Engineer prior to fabricating the units.B. The fabrication and installation of full scale model for part of metal works for inspection and approval of the Engineer before commencement of work.

8.1 ALUMINUM WORKS

Supply and install the following colored (powder coated, Migor'an) Dark gray Metallic color as per sample on site, Aluminum Mifromal Profile as made by NABCO , as shown on drawings ( All hinges and handles have to be powder coated same color as aluminum

Price shall include laminated glass 4/9/4mm , Ironmongery, fixing accessories original from Mifromal or Arpal such as rails, hinges, locks, brushes, rubber EPDM and angles must be original corresponding to each profile.Filling all sides and under the threshold and sills with SIKA FLEX 2H Pro color as of the aluminum color from out side and all exposed joints and MASTIC (NIRLAT made) from inside colored as the aluminum color All as instructed by the site engineer

Supply and install the followings ALUMINUM 7700 combinations NAPCO doors and windows, as per drawings and specifications, all as instructed by the site engineer

8.1.1AW01 with overall dimensions of (1.76x1.20m) As per drawings and Details.

No. 12


No. 8

8.1.3AW03 with overall dimensions of (1.60mx1.50) As per drawings and Details.

No. 1


No. 1


No. 12

Bill No. 8 Metal Works

14 of 25


Civil Works




No. 10


No. 2


No. 2


No. 1


No. 7

8.1.11GD01 with overall dimensions of (1.80X2.71m) As per drawings and Details.

No. 1

8.1.12GD02 with overall dimensions of (2.00x2.86m) As per drawings and Details.

No. 2


No. 1

8.1.14GD06 with overall dimensions of (3.00X2.71m) As per drawings and Details.

No. 1


No. 1


No. 1

8.1.17 Solar wall as per drawings and details. m2 30

8.1.18 solar chimney as per drawings and details m2 20

8.1.19 Window elevation in entrance size 2.60X3.55 No. 1

15 of 25


Civil Works



8.2 Steel Works


A. The submittal of shop drawings for the satisfaction of the Engineer prior to fabricating the units.

B. The fabrication and installation of full scale model for part of metal works for inspection and approval of the Engineer before commencement of work.

C. cleaning of all steel profiles prior to commencement with painting layers as specified and shown in drawings.

D. Supply all kinds of material and apply two coats of APC primer (ORANGE COLOR) Product Code: , drying period 3 days between each product

E. Supply all kinds of material and apply painting for steel, the price should include applying two coats of HAMMERITE paint with HAMMERITE dissolvent all as approved and instructed by the site engineer. The application should be carried out according to details and in conformity with the manufacturers’ specifications.

Supply and install the following steel doors, price to include cylinder, lock as made by WALLY, or approved eq., as a complete job,as shown on drawings.

8.2.1SD01 with overall dimensions of (1.20x2.71m) as shown on drawings

No. 1

8.2.2SD02 with overall dimensions of (2.27x3.38m) Louvers door as shown on drawings

No. 1

8.2.3SD03 with overall dimensions of (0.90x2.03m) as shown on drawings

No. 5

8.2.4

SD00 Garage galvanized Door 2mm from both side insulation with Foam with overall dimensions of (4.00x2.60m)the price include main steel frame 100X100X3.25mm to be fixed in the wall and z to be welding in the main frame and from the inside 100X50X3.25mm as shown on drawings

No. 1

8.2.5

Supply and install steel hand rails and stair rails, price to include all sections and stainless steel brushed 45mm diameter handle as shown on detailed drawings, instructed and approved by the site engineer

mr 55

8.2.6supply and install metal protection bars for windows and as shown on drawings .

m2 18

Total of Bill No. 8

16 of 25


Civil Works

Item No

Description Unit QTY Price /

Unit Total

Carpentry Works

The Contractor shall when pricing the rates of this bill, take into consideration including and allowing for the cost or expenses of all requirements stipulated in the preambles, drawings, and technical specifications.Wooden works shall include the following:

The contractor shall consider that all materials, woods, accessories, paint and the final work as whole to withstand the hard weather and humidity and counteract corrosion as much as possible.

In case that any specification stated below is not compatible with the above requirements the contractor will be fully responsible for the work.

1. Submittal of shop drawings prior to fabricating the units.2. The fabrication and installation of full scale model for part of wooden works for inspection and approval of the Engineer before commencement of work knowing that the sample is not part of the works and will not be paid for.

3. Veneers to be 6mm PLY wood

4. All external natural wood ( as per drawings and site engineer instructions) should be colored with water base color SIRCA made to be chosen by client, 2 coats of sealer with sanding between each layer, then one coat of

laquare paint SIRCA made. 5. All internal wood should be colored with alcohol based color , to be chosen by client ( the contractor should supply painting samples ) 3 coats of sillar base paint, and 2 coats of varnish ( Sirka type ) semi gloss, as per manufacturer's instructions.

5. All solid wood to be made of red OAK wood to be excellent quality American hard wood.

6. Solid wood is to be dry wood with humidity ratio not more than 9%. Humidity ratio in different samples chosen by the engineer to be tested by a renowned testing institute on the contractor expense.7. The contractor shall use screws ( Nail not accepted) in fixing mongery. The used glue should be Super sticky 99.

Bill No.9 Carpentary Works

17 of 25


Civil Works

Item No

Description Unit QTY Price /

Unit Total


8- All wooden accessories and iron mongery to be Nerosta color ( Brushed stainless steel), Samples to be approved by Architect

9- The contractor shall use sealant material all around wooden frames (such as but not limited to;Sikaflex-Pro 2HP ) during installation, and make good after and coloring and painting wall

9.1 Wooden doors & windows

Supply and install the following wooden doors, windows and frames complete with all necessary fixing accessories, glazing, hardware and iron mongery. All as shown in detailed drawings. The rate shall include the the supply and install of the following:-

1- Supply and install heavy duty hinge, 3 hinges for each door leaf Domicile 220 C 4*3.52- Supply and install locks for doors WALLY original type. Including cylinder, Master key system, Hyraychi should be approved by the owner prior to fabrication

3- Supply and install upper and lower lockers for each door Domicile AGB No. 320 - 400

4- Supply and install door handles type Domicil Type RO 11 - RY (Brushed Nikel Color)

5- supply and install special lock with for all upper keep windows. And two hinges for each leaf Domicile CEAM No. 2010.

6- All exposed edges, louvers and door frames are excellent quality hard American red OAK wood.

7- Glazing should be according to drawings

8- All doors' leaves to have stoppers from Domicile ref. DH003, All widows' leaves to have stoppers from Domicile ref. DH011.

WOODEN DOORS

Supply and install the following 45mm thick PLY wood doors, price to include PINE wood door frame and all iron accessories as instructed and approved by the site engineerPrice to include painting (Door & Frame)oil paint primer, 2 layers of PUTTY APC, 2 coats of under coat as made by APC or an approved eq. and 3 coats of APC ARAMAT as instructed and approved by the site engineer

9.1.1WD01, Double door with and overall dimensions of 1.2X2.00m as shown in drawings .

No. 4

18 of 25



Civil Works

Item

NoDescription Unit QTY

Price /

Unit Total


9.1.2WD02, with and overall dimensions of 0.80x2.00m

as shown in drawings. No. 21

9.1.3WD03, with and overall dimensions of 0.70*2.00m

as shown in drawings. No. 12

9.1.4WD04, with and overall dimensions of 0.90x2.00m

as shown in drawings.No. 1

9.2 Kitchen Cabinets

Supply and install kitchen upper and lower

cabinets with the following specifications:

1- All handles are as made by TIRADOR 2012/14

Length of handle 96/160 mm, Color is NIROSTA

MATT.

2- All hinges are as made by BLUM

3- All Ply wood used is 17mm ARRAD made or

equivalent that should be approved by the site

engineer.

4- Price should include counter top granite as

made by CAESAR color No. 7100 or approved

equivalent

9.2.1

Supply and install lower kitchen cabinets, as per

the detailed drawings and instructed by the site

engineer. Price to include granite counter top

mr 3

9.2.2

Supply and install Upper kitchen cabinets, as per

the detailed drawings and instructed by the site

engineer.

mr 2

9.2.3

Supply and install electromechanical cabinets,

price to include casement with 17mm thick

casement with solid 17x17mm RED OAK wood

frame and , installations as shown on drawings,

price to include hinges as made by BLUM, finishing

and painting as instructed and approved by the site

engineer

m2 12

9.3

Supply and install wooden PERGOLA with all

Accessories according to the attached drawings,

price should include painting a natural varnish

colour finishing 5 coats (two coat primer and 1coat

undercoat and 2 coats finishing ), the contractor is

responsible for executing the job as it is in the

drawings and according to site Engineer

instructions .( provisional )

m2 45

Total Item No. 9

19 of 25


Civil Works



10.1

Supply and install ORBOND water proofing (GREEN) gypsum board for false ceilings and on vertical walls of 12.5 mm thick gypsum panels with studs at every 40cm in both directions including decorations, forms, trims with all connections supports , fixing, putty sealer , wire mesh and special angles for edge of boards and all necessary accessories needed for the best completion of works . The contractor shall provide a shop drawing for architect approval.

The contractor should install paper corner and joints beads on all joints, corners, connections between walls and boards using putty (GOLD BOND BRAND), laying one layer of putty over the joints and corners and another one layer over all gypsum boards, sanding with sand paper and finishing all as approved by the site engineer

10.1.1On horizontal and vertical surfaces, as instructed and approved by the architect. m2 80

10.1.2

Supply and install service opening in the gypsum boards false ceiling where indicated on drawings or instructed by the site engineer, the price should include making the opening, making good of the gypsum edges, supply & install the pine wood frame and the ply wood, applying one coat of putty all as shown on detailed drawings and instructed by the site engineer

60x60cm service openingNo. 10

Total for False Ceiling works

Bill No.10 False Ceiling & Gypsum Works

20 of 25


Civil Works



The contractor should allow in his pricing that the engineer will use as many different colours or combination of colours to meet an approved colour scheme. ( Company ready mix original)No hand made color mix is allowed.

The contractor has to prepare a color sample 1*1m on site for each color asked by the site engineer

All paint works should conform to Tambour instruction regarding number of coats , rate of application or drying time.

All protection and care should be taken against paint drips, drops, droplets, and brushing.

The contractor should study well the project, walls, ceilings, gypsum boards, and all finished surfaces before applying the paint, so that if he discovers any mistake or additional needed works, he shall inform the engineer so as to adjust and agreed upon additional items before signing of the contractor. Otherwise the contractor will be responsible and take no extra money for any change of order.

Bill No.11 Painting Works

21 of 25


Civil Works



11 On Walls & Ceiling

Supply all kinds of raw material and apply paint for lobby and staircase walls to height 1.5 m , and wherever needed or instructed by the site engineer, the price should include preparing surface, clean, remove dust and foreign matter, sanding with well with sand paper, checking the walls with putty,laying two coats of putty (APC brand or an approved equivalent), applying one coat of APC SUPER BOND ROLL and applying Tow coats of APC Oil Painting or an approved equivalent Product, all as instructed and approved by the site engineer

m2 550

11.2

Supply all kinds of raw material and apply paint Emulsion for walls area ,and wherever needed or instructed by the site engineer, the price should include preparing surface, clean, remove dust and foreign matter, sanding with well with sand paper, checking the walls with putty, laying two coats of putty (APC brand or an approved equivalent), applying one coat of APC SUPER BOND ROLL and applying Four coats of APC Painting or equivalent Product, all as instructed and approved by the site engineer.

m2 2000

11.3

Supply and apply Four coats of APC FILL Aracid Product ceilings over plastering, electrical, mechanical shafts, elevator shaft and wherever needed or instructed by the site engineer.

m2 1500

Total of Bill No. 11

11.1

22 of 25


Civil Works

Item No

Description Unit QTY Total

Electrical lift works :simplex A No. of Units 1B Code: En 81.1 & and Palastinian standardsC Capacity 480 Kg, 6 Passengers D Velocity 1 m/sE Drive VVVF F Leveling Accuracy +/- 5 mmG Motion Control SimplexH Controller MicroprocessorI Stops 5J Doors NO. 5 in line K Floor Numbering 0,1,2,3,4M Shaft -Size W x D ( 1800 x1800 )mmN Overhead 4000mmO Pit Depth 1400 mm under slab on grade level .

Drive :1 Meconic-MX-GC-Gearless motor

1.1 Electronically controllled microprocessor regulated drive system

1.2180 starts/hours,AC-VVVF regulated,closed loop , power supply 3phase AC 400/230V,50Hz.stopping accuacy of (+/-5 mm)

1.3 Roping ____ with Special metel cables2 Control :

2.1 Microprocessor2.2 Overload function2.3 Fire emergency return control 2.4 Car light and fan auto on/off2.5 Re-leveling 2.6 Phase failure and phase reversal protection2.7 Over heat protection2.8 Full load bypass2.9 Automatic return to main floor2.10 Power control with sequential starting (power generator by owner)2.11 Independent operation2.12 Horn in car2.13 Anti nuisance (false calls cancellation)2.14 Nudging operation

2.15Emergency evacuation system in case of power failure to reach thenearest landing equiped with stand by battaries

2.16The elevator call system should be controlled with a Magnatic CardReader on each door.

3 Car Finish :3.1 Elephant skin stainless steel on all sides

3.2 Ceiling suspended with indirect lighting with stainless steel mirror finish

3.3Removable ceiling for maintinance task, enough space for maintinaceman

3.4 Emergency exit 500 x 600 mm3.5 Brushed Stanless Steel handrail at front elevation of the room3.6 Floor finish (red stone or Granite) To be supplied by the owner.4 Car operating panel

4.1One COP, full height colored steel Anthracite Ral _____ at side wallpanel

4.2 Micro touch push Buttons for landing (floor designations)4.3 Alarm button 4.4 Door open, button4.5 Door close button 4.6 Digital position indicator dot matrix 4.7 Direction arrows.

Bill No.12 Electrical Lift (Elevator) Works

23 of 25


Civil Works

Item No

Description Unit QTY Total

Bill No.12 Electrical Lift (Elevator) Works

4.8 Intercom system 2 terminals (car, supervision room),4.9 Overload protection device with audible and visible signal,4.10 Emergency bell and light

5 CAR DIMENSIONS:5.1 Width * Depth * Height:1600x1500x23006 CAR DOORS:

6.1 Car door: Fully automatic 2 panels, heavy duty.6.2 Car door drive: is regulated with AC-VVVF 6.3 Opening: Telescopic opening 2 doors panels 6.4 Door sill : Elephant Skin Stainless Steel. 6.5 Panels finish : Elephant Skin Stainless Steel. 6.6 Shoulders finish for car: Elephant Skin Stainless Steel. 6.7 Door safety device type : light curtain.6.8 Door open/close time is adjustable.6.9 Pre-opening at landings 7 LANDING DOORS:

7.1 Door (width X height):1200X2000 mm7.2 Door panels finish : painted steel finish at all floors7.3 Door frame: narrow in painted steel finish at all floors

7.4Fire resistance class F-60. (landing doors are 60 minutes fireresistance)

7.5 Landing operation and indication panels on all floors7.6 Position indicator dot matrix type, direction arrows. Wall mounted.

7.7Push Buttons: square type micro touch, with mirror stainless steel plate at all floors

8 Fireman Function:8.1 Fireman Key switch at MAIN FLOOR.

9 NO-MACHINE ROOM :Machine Room Less (MRL)

10 SAFETY GEAR :For Car

11 BUFFERS: buffers for car and counter weight

12 COUNTER WEIGHT : Cast Iron enclose in steel framework

Notes : -

aEach company should submit its own specifications andrequirments .

bAny scaffolding works should be done by the company and on itsexpense .

cAll steel beams needed for doors , or any where else , to besupplied and installed by the company .

Job 1

Total of Bill No. 12

24 of 25


Civil Works

Bill No. Description Total

Excavation & Earth Works

Concrete Works

Stone Works

Block Works

Plastering Works

Tiling Works

Water Proofing Works

Metal Works

Wooden Works

False Ceiling Works

Painting Works

Electrical lift

Total of Civil Works -including provisional items (Not Including Value Added Tax )

Currency of Bid (NIS or USD) : ________________

5

6

7

12

8

9

10

11

Summary of Civil Works Bills 1 - 12

1

2

3

4

25 of 25



BOQ Mechanical Works


Mechanical Works

No. Description Unit Qty Unit Rate Total

1 Waste and drainage systemThe Contractor shall, when pricing the rates of this bill,take into consideration including and allow for the costsor expenses of all requirements stipulated in thepreambles, drawings.

The following notes should be considered when pricing:

1- The price shall include all required digging orexcavation backfilling,coring and cement covering asspecified.

2- The price shall include all connections to exsistingdrainage pipes and manholes if needed.includdedcutting in tile & asphalt ,retiling,repair the asphalts

3- The contractor must consider keeping the systemrunning where needed during the whole constructionperiod.

1.1

Supply and Install (S&I) U.P.V.C HULIOT pipes andfittings for waste & rain water, and sanitary water stand pipes, running exposed along partitions, walls, shafts,under tiles, laid in walls. Price include all type ofsupports, hooks, and all excavation, sand embedment,back filling and concrete coring by hilti for creatingopenings, all types of fittings as but not limited to; wye, tee, reducer tee, 45 degree elbow, end caps,expansion joints, .laying at least 8cm concrete aroundthe under ground pipes

1.1.1 6" pipe suspended to ceiling L.m 30

1.1.2 4" pipe L.m 220

1.1.3 3" pipe L.m 20

1.1.4 2" pipe L.m 90

1.1.5 11/4" pipe condensate fan coil L.m 35

1.2

S & I 4"/2 Floor trap or box trab as by lipski includingstainless steel cover 15x15cm floor drain cover. Therate shall include for all connections with drain pipes2"pipes, 4"/2 extending box and nipple. and all neededfittings for proper installations.

No 11

1.3

S & I 4"/4 Floor trap Huliot including stainless steel15x15cm floor drain cover. The rate shall include forall connections with drain pipes2" pipes, 4/2" extendingbox and nipple lipski. and all needed fittings forproper installations.

No 16

1.4S & I 4" clean out openings including stainless steel15x15cm floor drain cover. The rate shall include forall connections with drain pipes .

No 11

1.5 S & I 4" P.V.C vent caps for all vent pipes at roof No 4

1 of 12


Mechanical Works


1.6

S & I 20x20cm Rain water Floor trap box ready typeincluding . The rate shall include for all connectionswith rain pipes 4" extending nipple. and all neededfittings for proper installations.

No 8

1.7

Supply and install rain water trench size 100x20x12cm type ready,as shown in the drawingscomplete with 4" floor trap ready type16mm stainlesssteel rods at the top and 5cm apart and all necessarayaccessories.a slope towards the outlets of the draintrench shoud be made.perforated basket .price includedigging,excavation and all necessaray work tocomplete the job

No 6

Ditto but 30 x20cm trunch for the parking M.R 4

1.8

Supply and install of supmersible pump complete withfloat valve, to be install in the manhole under the liftroom, to collect all the rain water outside as shown inthe drawing,price include supply and install of manhole60x60cm with steel cover above the manhole with16mm steel rods and 3cm apart, price also include the40mm H.D.P as shown in drawings and all ellectricalconnection.type dab or eq pump head,1mh-7m3/h

job 1

1.9

Supply and install of 4" perforated pipe to be installaccorrding to Drawing price include all necessarayfitting to connect the perforated pipe to the rain waterpipe,with all requird fitting to complete the jobaccorrding engineer request

L.m 70

Total of waste and rain water systems

2 of 12


Mechanical Works


2 External Drainage collection systemThe Contractor, when pricing the rates of this bill, shalltake into consideration including and allowing for thecosts or expenses of all requirements stipulated in thepreambles, drawings and technical specification of thecontract.


1- The price shall include all required digging orexcavation, backfilling and cement covering asspecified.

2- The price shall include all connections to existingdrainage pipes and manholes if needed.includdedcutting in tile & asphalt ,retiling,repair the asphalts

2.1 Excavation

Supply and install 6" UPVC pipes HOLUIOT Taken tothe exsisting manhole including digging forpipes,gutting,opening in walls an in manhole,supplywith all necessary fittings such aselbow,tee,Y,….etc,for sewage disposal and vent pipe,the price allso include fordigging,supports,hanggers,and laying at least 8cmconcreate arround the pipes,approve manufacture forpipes and fittings: ( red blassim)

L.m 50

2.2 Manholes :

Supply and install of 60cm (internal diameter) readymade concrete circular manhole of depth notexceeding 100cm measured from ground level at thetop of the manhole cover to the top level of themanhole base. internal epoxy coating, benching.Special connection pieces should be used for fixing thepipes with the manhole. The price is to includenecessary excavations, backfilling, and protection andas directed by the Engineer. Supply and Installation ofcast iron cover of 25ton Kurdieh type or eq. shall beinclude in the rate of the manhole

No. 4

2.3Ditto but 80cm internal diameter exceeding 1m depthwith cast iron cover 8 ton type kurdieh or eq. allaccorrding to engineer instructions

No. 2

Total of External drainge systems

3 of 12


Mechanical Works


3 Sanitary fixture and their accessories

The Contractor shall, when pricing the rates of this bill,take into consideration including and allow for the costsor expenses of all requirements in the drawings


1- The price shall include all required digging orexcavation backfilling,coring and cement covering asspecified.

3.1

Supply and install wall mounted water closet creavittype SL or eq. pergamone colour.complete withreccesd plasson or shwaab nicara ,heavy duty seatcover,complete with crome plated screw,outlet soilfitting with cleanout,1/2"x3/8" angle valve nile type oreq.,connection to soil pipe,connection to watersupply.includding paper holder chrome platted.

No. 12

Supply and install handicap water closet suite creavittype BD3041 or eg. with porcelain nicara pergamonecolour floor standing type,complete with crome platedscrew,outlet soil fitting with cleanout,1/2"x1/2" anglevalve type nil or eq.,1/2" flexible white colourplastichose,heavy duty seat cover of the same type,,connection to soil pipe,connection to watersupply.includding paper holder chrome platted,PriceInclude supply and install two support arms stainlesssteel Dia 32mm one fixed, one movement type creavitTB200,TB110 or approved equal accorrding engineerruquest

No. 1

3.2

Supply and install porcelain wall hang wash basinpergamone colour, with half leg creavit type

SL6026 or eq..price shall include hot and coldwater mixing faucet hamat type 300-140 oreq,two 1/2" x 3/8" angle valve nil type oreq.,11/2"P-Trap,connection to supplypiping,connection to drainge pipe.

No. 1

4 of 12


Mechanical Works


3.3 Ditto but under counter wash basin No. 11

Supply and install for handicap porcelain wall hang wash basin pergamone colour, creavit type BD060 or eq.price shall include hot and cold water mixing faucet hamat type or eq.,two 1/2" x 3/8" angle valve type nil or eq,11/2"P-Trap,connection to supply piping,connection to drainge pipe. Supply install one support arms stainless steel Dia 32mm movement type accorrding engineer ruquest

1

3.4

Supply and install stainless steel kitchen sink, singlebowl according to drawings with shelf as by *Roca oreq. , Hamt mixer type 300-153 or approved includingsiphon and complete with angle valves. 1/2x3/8" nile typeor approved accorrding engineer ruquest

No. 1

Total of Sanitary fixture

5 of 12


Mechanical Works


4 Domestic water system

The Contractor shall, when pricing the rates of this bill,take into consideration including and allow for the costsor expenses of all requirements stipulated in thepreambles, drawings .the contractor shall consider keeping the interruptionfor the system to a minimum.Testing all pipes at 8bar for 24 hour

4.1

Supply and install and test galvanized steel pipe sch.40 for cold and hot& soft water supply with all necessaryfittings such as elbow,tee,reducer,union,valves,sshown in the drawings.the price shall include forhangers, supports,openings in wall by hilti,sleeves,painting and rolling of asphalted canves mesh for theunder ground pipes, Also insulatuon the hot waterpipes by 13mm ruber foam insulation(anavid) wrappedwithcolared self adhesiveP.V.C tape.shown

4.1.1 1/2" LM 50

4.1.2 3/4"ditto. LM 60

4.1.3 1" ditto LM 70

4.1.4 11/4" ditto LM 35

4.1.5 11/2" ditto. LM 20

4.1.6 2" ditto. LM 20

4.2Supply and install PVC plastic pipe(jolani) or approvedequal for sanitary fixture with all necessary fittings.16/25mm pipes,1/2" wall elbow type N.T.M

LM 400

4.3 Ditto but 25/32mm LM 50

4.4 Ditto but 32/40mm LM 50

4.5

Supply and install Gaccomini* or eq.type copper watercollectors complete with plugs, washers, brackets, draincocks,vents, isolating ball valves with T-handle on eachoutlet. The unit price shall include supply and install of 2mm steel cabinet painted in oven bymanufacturer.Number of outlets are as shown ondrawings size of cabinet according collecter size

collecter-1: 13eye cold(11/4"),7 eye hot (1") NO 1

collecter-2: 9 eye cold(11/4"),7 eye hot (1") NO 2

collecter-3: 7 eye cold(1"),3 eye hot (3/4") NO 2

collecter-4: 7 eye cold(1"),6 eye hot (3/4") NO 1

6 of 12


Mechanical Works


collecter-5: soft 3 eye (3/4") NO 1

4.6 Supply and install 1/2" tap for irrigation italy type NO 5

4.7

Supply and install electrical water heater of typeoriginal or approved of capacity 60L the price includeall necessaray fitting needed to complete the work,therate also include all wirring,cables, needed to operatethe boiler

NO 2

Ditto but 30L capacity NO 3

4.8

Supply, install and connect copper gas pipes type wicofor the different fixtures and as shown on drawings,complete with all necessary fittings, accessories,regulator, shut-off valves, etc..price include pvcsleeves of bigger diameter, ,covering the pipe byconcrete for safty,price also include all excavation,coring by hilti for installation the pipes and all worksneeded to complete the work.coated gaz pipe dia16mm

LM 30

Ditto but 8mm gaz pipe LM 80

Supply and install 1/2" gaz collecter including shut offvalves SAGIV type at main and sub mainbranches,complete with hangers,and accessoriesneeded to complete the work.accorrding engineerrequest,7eyes The unit price shall include supply andinstall of 2 mm steel cabinet painted in oven bymanufacturer.Number of outlets are as shown ondrawings size of cabinet according collecter size

Job 1

Total of Domestic Water System

7 of 12


Mechanical Works


5 Ventelation system

5.1

Sypply and install in line exhaust fan for toiletsroom,of type vortice or eg,price include all necessarayfitting to connect the fan to exhaust grill on bath roomabove false ceiling,also price include coring in wall byhilti for the duct and exhaust grill ,and all wirring andcables needed to operate the exhaust fan with timmerfan 300 cfm

NO 1

5.2 Ditto fan 200cfm NO 1

5.3 Ditto but wall type ex.fan 100cfm NO 1

5.4

Sypply and install roof top centrifugal exhaust fan forhood,of type vortice or eg.complete with galvanizedmetal sheet elbow and bird mesh at the dischargesection ,price include all necessaray fitting to connectthe duct to exhaust fan on roof,also price includeconcrete base for the fan and rubber under the fan forvibration also supply and install all electricalwirring,cables,switch,to operate the fan 2500cfm,1.2"sp

NO 1

5.5Supply and install 6" and 4" flexible tubes including allnecessary fittings such as elbow, Y, hangers, supports,etc. Approved manufacturer of tubes (Dec)

L.M 40

5.6

Supply and install rectangular not insulated duct ofthickness 0.7mm for the exhaust air duct for toilet room,and for solar chimney which running in walls andpartions accorrding archicets drawings Complete withhangers, supports, bolts, nuts, etc.

Sq.m. 30

5.7Supply and install aluminum exhaust grille as per"Metalpress*"

5.8 Sypply and install exhaust grill circular 6"x6" NO 1

5.9 Sypply and install exhaust grill circular 6" NO 6

Total of Ventelation system

8 of 12


Mechanical Works


6 Fire Fighting System

The Contractor shall, when pricing the rates of this bill,take into consideration including and allow for the costsor expenses of all requirements stipulated in thepreambles, drawings .

Testing all pipes at 8bar for 24 hour

6.1

Supply and install fire cabinets of sufficient size topermit for installation of necessary equipment asshown on drawings . The cabinet shall include thefollowing: Fire hose 3/4" in diameter, 25 meter long,light weight, made of red rubber with working pressureof 150 psi. Hose reel of the swinging type, up to 180degrees full swing complete with guide arm. Chromeplated 3/4" in diameter nozzle capable of completeshut-off. Gate valve 1" in diameter. Fire hose 2" indiameter, 15 meter long, light weight, made of linen.Chrome plated 2" in diameter nozzle capable ofcomplete shut-off. Angle valve 2" in diameter of bestquality . Hose adapter 2" in diameter 3 Kgs. Chemicalfire extinguisher with spray hose and nozzle.

Unit 6

6.2

Supply and istall galvanized steel pipes to ASTM-A53grade "A" schedule-40 for fire fighting systempipework, inside building. The unit price shall includevalves, fittings, and all accessories and works requiredto complete the work and as per preambles,specifications, and the supervision of engineer'srequirements. The unit price shall also include theconnection to existing system in boiler room completewith cutting, taking branch, etc..

2" diameter pipe Mr 80

1" diameter pipe Mr 20

Total of Fire Fighting System

9 of 12


Mechanical Works


7 PUMP ROOM&ROOF

The Contractor shall, when pricing the rates of this bill,take into consideration including and allow for the costsor expenses of all requirements stipulated in thepreambles, drawings .Testing all pipes at 8bar for 24 hour

7.1

supply and install cold&fire water pressure pumpgrandfoss or Eq. vertical multi stage type ,completewith all nessesary fittings such as ,press gage,pressure reducing valve,press stat danfoss type,andall necessaray fitting such as valves,strainer,flexsiblejoint,check valve, to complete the job Price include forelectrical,wirring,and connection to operate. pump5M3/H,50MH

NO 1

7.2 Ditto for all fitting but jokey pump 2M3/H,60MH NO 1

Ditto but for soft water 2M3/H-50MH NO 1

7.3

Supply and install pressure tank elbi type or approvedequal, as shown on drawings complete with all fittingssuch as automatic air vent, pressure reducing valve,gate valve, T, union, etc. Price includes pipinginstallation for water from main cold water pipe.Maximum pressure of tank is 6 atm. 100 lit. capacity.

No. 2

7.4

Supply and install 2" H.D.P pipe,price include theflange,with the valve needed for the water tank (well )with all necesaray fitting and pipe needed to reach topump room,all pipe inside the parking to the pumproom well be install under the slab concrete accorrdingdrawing

MR 15

7.5

Supply and install of o.5 mm galvanize sheet matelduct to gladding all the exposed pipe on roof priceinclude all necessaray fittings,such astee,elbow,valves,for all diminssion of pipes to 2"

MR 30

7.6

Supply and install softner type permo or approvedequal complete with all necessaray fitting to connectthe softner with the pressure pump and the sulttank,the rate include all the electrical wirring ,cables tocomplete the work permo type data -7 -2m3/h,orapproved equal accorrding engineer ruquest

NO 1

10 of 12


Mechanical Works


7.7

Supply and install three solar panels of original type

approved equal,9 section each one and of size 90*190 cm. Complete with 180l hot water storagetank. the tank shall be painted by epoxy from insideand shall be equiped with electric heating elementof capacity 2500w, price include all necessarayfittings,also the price include metal base febricatedof steel angle 40x40x5cm,and electricalconnection,necessaray fittings needed to finish thework accorrding to engineer instructions

set 2

7.8

Supply and install PVC water tank of capacity 1500lit with steel base 1m for the soft water , the price shall include fittings such as ,1/2" floater,3/4" drain pipe with valve,and all necessary fittings for pipe ,such as ,elbow,T,union,valves, all accorrding engineer request

No. 1

Total of pump work

11 of 12


Mechanical Works


Total of waste and rain water systems

Total of External drainge systems

Total of Sanitary fixture

Total of Domestic Water System

Total of Ventelation system

Fire System

Total of pump work

Total of Mechanical Works-including provisional items (Not Including Value Added Tax )


Summary of Mechanical Works Bills

1

2

3

6

7

4

5

12 of 12



BOQ Electrical Works


Electrical Works

Item Description Unit QTY Unit Rate Total

Electrical and Communication Works

The contractor shall, when pricing the rates of the

following electrical bills take into consideration including

and allow for the cost expenses of all requirements

stipulated in the preambles, drawings and technical

specifications of the tender.

All Supplied Materials Should be class A , new , not used

and Free From any Defects, Having the Supervisor

approval Certificate .

The contractor's total price for works shall include for the

supply, execution, completion and testing of the whole of

electrical installation works and related systems in

accordance with the drawings, bill of quantities and

specifications.

The contractor shall coordinate his works with the

decoration works, furniture, changes in the positioning of

ceiling light fixtures due to partitioning changes and any

other changes which require design changes on the

tender drawings.

The contractor must consider all these changes in the

shop drawings which must be submitted and approved

before commencement of works.

Plates, labels and tags for the identification of plant,

equipment, cables, switches ,sockets and the like.

Forming or cutting holes, chases, channels etc. in

reinforced concrete structures and block works.

The contractor's rate must include the supply and install

internal sea sand plastering for the electrical conduits on

wall . composed of two coats base coat ,finish coat . The

rate includes all necessary patching works ,expanded

metal latch mesh , plastering layers must be applied to

meet plastering thickness

The contractor shall submit all samples needed for all

electrical and low voltage points, fittings , accessories

and fixtures and to take the approval from the

supervision engineer before starting works.

All electrical conduits under tiles, floor, wall should be

protected by cement mortar or concrete layer and all

electrical excavation works should be removed from site

as specified in the technical specification and drawings.

1 of 15


Electrical Works


The above mentioned shop drawings, electrical

switchboards shop drawings, as built drawings and all

other required detailed drawings are to be included in

the rates for no additional cost.

1 Main Feeder

1.1.1Feeding the building with the 3*125 A electrical amperes

needed . ( Estimated by the Municipality of Hebron)L.S. 1

1.2 Main Line Excavation for main power cable

1.2.1

Supply all labor and materials to make an excavation of

80cm (deep) x 60cm (wide). The excavations for trenches

80cm width x 100cm depth in any type of soil and

removing extra excavated materials out of side. Work

shall include supply and filling works of 20cm sand layers

and laying 10cm concrete block with special electrical

warning tape. Work shall also include backfilling with

chosen excavated materials and compacted it with layers

20cm thickness.

M.L. 25

1.3 Main Line Excavation for main telephone cable

1.3.1

Supply all labor and materials to make an excavation of

80cm (deep) x 60cm (wide). The excavations for trenches

80cm width x 100cm depth in any type of soil and

removing extra excavated materials out of side. Work

shall include supply and filling works of 20cm sand layers

and laying 10cm concrete block with special electrical

warning tape. Work shall also include backfilling with

chosen excavated materials and compacted it with layers

20cm thickness.

M.L. 25

1.4 Empty Conduits for Main Cables

1.4.1

Supply, install, test and commission a heavy duty UPVC

conduits dia 4" with pull wire for main incoming power

cables to main distribution board to be laid in the

excavation in item 1.2 with all accessories.

M.L. 50

1.5 Empty Conduits for Main Telephone Cable

1.5.1

Supply, install, test and commission a heavy duty UPVC

pipe dia 2" with pull wire for main telephone cables

complete to be laid in the excavation in item 1.4 with all

accessories.

M.L. 50

2 of 15


Electrical Works


1.6 Main Power Manholes

1.6.1

Supply ,install, and test a ready made main civil heavy

round duty manholes and with special cast iron covers 25

Ton Load Capacity and Ø100 with 100cm depth. Work to

include pouring all needed concrete materials for

manholes bases with steel meshØ12mm/20cm in both

directions, work also include backfilling and removing all

extra excavated materials and with all necessary

accessories.

No. 3

1.7 Main Low Voltage Manholes

1.7.1

Supply ,install, and test a ready made main civil heavy

round duty manholes and with special cast iron covers 25

Ton Load Capacity and Ø80 with 80cm depth. Work to

include pouring all needed concrete materials for

manholes bases with steel meshØ12mm/20cm in both

directions, work also include backfilling and removing all

extra excavated materials and with all necessary

accessories.

No 1

Total of Main Feeder Works

3 of 15


Electrical Works


2 Electrical Switchboards

Supply, Install and Connect Main and Sub Main

Distribution Board. . Price to include metal panel board

oven painted 1.5mm thickness factory made, Moulded

Case circuit breakers MCCB , miniature circuit breaker

MCB , bus bars, cable clamps, cable glands, protection

equipments, measuring equipment, labeling all circuit

breakers, all necessary excavation, fixing . asdrawings and specifications with all accessories.Types of MCCB's and MCB's, Moller , Merlin GerinGeneral electric or equivalent. Rated BreakingCapacity for circuit breakers as follow

10 A‐16 A ‐ 10 KA

25A ‐125 A ‐ 25 KA

160A ‐400 A ‐ 36 KA

10 A‐16 A ‐ 10 KA

25A ‐125 A ‐ 25 KA

160A ‐400 A ‐ 36 KA

2.1 MDB with Power Factor Correction No. 1

2.2 DB1 No. 1

2.3 DB2 No. 1

2.4 DB3 No. 1

2.5 DB4 No. 1

2.6 PLIFT No. 1

Total of Electrical Switchboard Works

4 of 15


Electrical Works


3 Installation in the Building Points

The following items are supply, installation of same,

connection, wiring, commissioning and all other details,

as specified in the technical specification and drawings.

3.1

Wall, ceiling or false ceiling mounted lighting point

normal, waterproof, emergency or exit (Price includes

16mm diameter conduit Nacy , hadash plast type or

equivalent, 3x1.5 mm2 cross section wire itac ,

synenergy type or equivalent, ceiling box and phase line

for emergency lighting point , and leading from the

switch panel to the point including any needed boxes or

accessories).

No. 300

3.2

External flood Light Point (Price includes 1" diameter

conduit, 3x2.5 sq.m N2XY cross section cable or

equivalent, with all excavations needed and leading from

the switch panel to the point including any needed boxes

or accessories).

Point 5

3.3

External wall mounted lighting point (Price

includes16mm diameter conduit Nacy , hadash plast

type or equivalent, 3x1.5 mm2 cross section cable itac ,

synenergy type or equivalent and leading from the

switch panel to the point including any needed boxes or

accessories).

No. 35

3.4

Single pole switch GEWISS Top System GW20571,or

Biticino, Legrand or equivalent Including Boxes,

Supports & Plates, (Price includes 16mm diameter

conduit Nacy , hadash plast type or equivalent, 3x1.5

mm2 cross section wire itac , synenergy type or

equivalent, and all accessories.

No. 6

3.5 Ditto but waterproof No. 6

3.6

Double pole switch Legrand or equivalent Including

Boxes, Supports & Plates, (Price includes 16mm diameter




No. 22


3.8

Two way switch Legrand or equivalent Including Boxes,

Supports & Plates, (Price includes 16mm diameter




No. 8

3.9

Intermediate switch Legrand or equivalent Including

Boxes, Supports & Plates, (Price includes 16mm diameter




No. 1

5 of 15


Electrical Works


3.10

Push button with indication lamp Legrand or equivalent

Including Boxes, Supports & Plates, (Price includes 16mm

diameter conduit Nacy , hadash plast type or equivalent,

3x1.5 mm2 cross section wire itac , synenergy type or


No. 10

3.11

Standard 1 ph socket outlet point normal (Price includes

16mm dia. conduits Nacy , hadash plast type or

equivalent, 3x2.5mm2 wire itac , synenergy type or

equivalent , with 16A socket Legrand or equivalent,

Boxes, Supports & Plates and leading from the switch

panel to the point , including all accessories).

No. 60


3.13

Standard 1 ph Double socket outlet point normal (Price

includes 16mm dia. conduits Nacy , hadash plast type or

equivalent, 3x2.5mm2 wire itac , synenergy type or

equivalent , with 16A socket GEWISS Top System

GW20220 type or Biticino, Legrand or equivalent, Boxes,

Supports & Plates and leading from the switch panel to

the point , including all accessories).

No. 35


3.15

16A Industrial three phase wall‐mounted socket outlet

point (Price includes sockets NISKO type N516.110 with

lockable cover, IP 65 , three and single phase Legrand

type or equivalent, 5x2.5mm2 N2XY cable orequivalent, 23mm diameter conduits, and allaccessories leading from distribution board to thepoint).

No. 3

3.16

Single phase electrical connection of Split Unit (Price

includes 3x2.5mm2 N2XY or equivalent cross section

cables, A/C socket LEGRAND type or equivalent, flexible

heat conduits, cable glands, connection boxes, adaptors

and all connections and accessories from relevant panel

to machine .

No. 30

3.17

One phase electrical connection point for electrical

Boiler on roof (Price includes 16mm dia. conduit,

3x2.5mm2 N2XY cross section cable or equivalent, with

ON‐OFF switch Legrand or equivalent. Rates also includes

isolator switch w.p , Boxes, Supports & Plates and leading

from the switch panel to the point , including all

accessories).

No. 1

6 of 15


Electrical Works


3.18

On‐off switch with indication lamp ,including Price

includes 16mm dia. conduit, 3x2.5mm2 N2XY cross

section cable or equivalent, with ON‐OFF switch Legrand

or equivalent. Rates also includes Boxes, Supports &

Plates and leading from the switch panel to the point ,

including all accessories).

No. 5

3.19

Telephone connection point wall or table mounted (Price

includes 16mm diameter conduits Nacy , hadash plast

type or equivalent, with 4x0.5mm2 ITAC telephone or

equivalent, telephone socket legrand or equivalent,

Including Boxes, Supports & Plates and leading from

point to the telephone section in LV box).

No. 40

3.20

T.V. antenna connection point (The price includes 16mm

diameter conduits Nacy , hadash plast type or

equivalent, with American common scope coaxial cable

RG6 75 ohms,, as well an outlet with a plastic socket

legrand or equivalent, Including Boxes, Supports & Plates

and leading from point to the connection box on roof.

No. 10

3.21

Satellite antenna connection point (The price includes

16mm diameter conduits Nacy , hadash plast type or

equivalent, with American common scope coaxial cable

RG6 75 ohms, leading from connection box to the points

as well an outlet with a plastic socket GEWISS LEGRAND,

Including Boxes, Supports & Plates and leading from

point to the connection box on roof.

No. 10

3.22

Intercom System connection point (Price includes 16mm

diameter conduits with 8*0.5 mm2 cable ITAC type orequivalent, and leading from point to the LV box orto the nearest point with all accessories).

No. 5

3.23

Fire detection system connection point, (Each outlet for

smoke , heat detectors, break glass , indoor or outdoor

alarm horn, shall be measured as one point. Price

includes 16mm2 conduits and cables 4x0.8 mm2 ITAC

type or equivalent, and leading from point to the fire

detection section in the communication cabinet or to the

nearest point and all accessories).

No. 80

7 of 15


Electrical Works


3.24

Computer outlet connection point wall or table mounted

(The price includes 16mm2 conduits with 4 pairs

computer cable shielded type FTP CAT 5E and leading

from the telephone communication cabinet or computer

HUB to the points as well an outlet with a plastic socket

Legrand or equivalent including Boxes, Supports & Plates

and all accessories).

No. 45

3.25

Electrical Connection for 1‐ phase lifting Pumps. (Price

includes all necessary cables 3X1.5mm2 ITAC type or

equivalent , flexible heat conduits, Isolator switch 10A

cable glands, connection boxes w.p, labeling, adaptors

and all accessories and leading from Relevant panel to

machine to the satisfactory of the engineer.

L.S. 1

3.26

Electrical Connection for 1‐ phase Pumps on roof. (Price

includes all necessary cables 3X1.5mm2 ITAC type or

equivalent , flexible heat conduits, Isolator switch 10A

cable glands, connection boxes w.p, labeling, adaptors

and all accessories and leading from Relevant panel to

machine to the satisfactory of the engineer.

L.S. 1

3.27

Electrical connection of Single phase Extract Fan (the

Price includes 16mm diameter conduit, 3x1.5mm2

cables ITAC type or equivalent, Isolator switch 10A cable

glands, connection boxes w.p, labeling, adaptors and all

accessories and leading from Relevant panel to machine

to the satisfactory of the engineer.

Point 4

Total of Installation Works

8 of 15


Electrical Works


4 Lighting Fixtures and Accessories

Note: work for lighting fixtures is to include supply of the

fixtures specified, installation of same connection, wiring,

commissioning, lamps OSRAM type, tubes, starters

louvers, connections, suspension, clamps and all other

accessories necessary to provide a complete fitting with

all terminals and rates also includes all L,Z and omega

profiles if needed , great opening for lighting fixtures in

gypsum board and all other details , as specified in the

technical specifications and drawings and as approved by

the engineer.

4.1Type (A) 2x36w surface mounted light fixture with parabolic louvre GAASH or equivalent .

No. 70

4.2Type (A1) 4X18W recessed light fixture with double parabolic as GAASH or equivalent..

Unit 10

4.3Type (B) 2x36w fluorescent surface mounted light fixture IP65 GAASH or equivalent .

No. 45

4.4Type (E1) 1x8w emergency exit sign with 3 hours maintained duration GAASH or equivalent.

No. 5

4.5Type (C) 2X18W surface mounted light fixture with clear prismatic diffuser IP20 GAASH or equivalent .

No. 80

4.6Type (D) 2X26W surface mounted light fixture with clear prismatic diffuser IP54 GAASH or equivalent .

No. 30

4.7Type (F)100W wall mounted light fixture light IP65 with die cast aluminum body grey color GAASH or equivalent .

No. 30

4.9Type (G) 50w 12V spot light including electronic transformer TARGETTI BTT

Unit 20

4.8 Type (H) 18W wall mounted light fixture LUXTEN or equivalent Unit 4

Total of Lighting Fixtures and Accessories

9 of 15


Electrical Works


5 Cables & Conductors / Leads

Supply, install, test and connect the following electrical

cables , including insertion into conduit or attachment to

structural elements or laying in ductwork, including all

associated materials, insulation materials, unions,

labeling and connection of cable at both ends and all

accessories).

5.15x16 sq.mm cross section N2XY cable type Synergy or

ITAC or equivalent.M.L. 50

5.25x10 sq.mm cross section N2XY cable type Synergy or

ITAC or equivalent.M.L. 125

5.35x2.5 sq.mm cross section N2XY cable type Synergy or

ITAC or equivalent.M.L 50







5.7Copper conductor with PVC insulation cross section

16sq.mm type Synergy or ITAC or equivalent.M.L 100

Total of Cables & Conductors Works

10 of 15


Electrical Works


6 Cable Conduit & Ducts

Supply, install, test and connect the following standard

conduits or color fire proof conduits, processed over or

under plaster or over false ceiling, including junction

boxes, unios, connectors, etc… including galvanized draw

strings, ready for use "Pony last" type or equivalent and

all accessories).

6.142mm diameter heavy, bendable type NACY, Had ash

Plast or equivalent.M.L 150

6.229mm diameter heavy, bendable type NACY, Had ash

Plast or equivalent.M.L 200

6.323mm diameter heavy, bendable type Had ash Plast or

equivalent.M.L 400

6.416mm diameter heavy, bendable type Had ash Plast or

equivalent.M.L 300

Total of Cable Conduit & Ducts

7 Telephone Cable and low voltage box

Supply, install, test and connect metallic low voltage box

for Telephone, TV , CCTV systems .The size of the low

voltage shall be the same height and depth of the

nearest electrical board with 30cm width .

7.1 MLV No. 1

7.2 LV1 No. 1

7.3 LV2 No. 1

7.4 LV3 No. 1

7.5 LV4 No. 1

7.6

Telephone cable 1NO. 32 pairs Superior from telephone

exchange to the low voltage boxes price includes

terminal blocks, corona and 23 mm fire proof conduits.

M.L 100

Total of Telephone Cable and low voltage box

11 of 15


Electrical Works


8 Grounding Works

8.1

30x3.5mm galvanized steel strip ( ROLL) to be welded to

building foundation reinforcement and connected to the

equipotential bus bar of (MDB) by means of 35 mm2

insulated copper conductor including cable shoe and all

required materials, boxes, testing terminals, and all

accessories.

Job 1

8.2

Grounding electrode, made up of a 19mm diameter

copper plated steel rod, such as manufactured by

"ARDING", electrode length: 1.5m, including an

inspection chamber40*40 cm and cover, and a 25 sq.mm

exposed, woven copper conductor, from electrodes to

potential equalizing bus bar in MDB complete with all

accessories.

No. 5

8.3

30x3.5mm galvanized steel strip to be welded to

Generator foundation reinforcement and connected to

the equipotential bus bar of generator panels by means

of insulated 50 mm2 copper conductor including all

required materials, earthing boxes, earth bus bar, testing

terminals, and all accessories.

Job 1

8.4

Grounding of cold and hot water piping, fuel piping, air

conditioning piping, ducts, elevator rails, main and sub

main distribution boards, metallic sewage , supply trunks

metallic cable ducts, Generator, EPABX and any other

metallic service in the building. Rate to include 16 mm2

copper conductors as shown on drawings, main and

secondary potential equalizing bus‐bar, protective

conduit, junction box, complete with all necessary

accessories.

Job 1

Total of Grounding Works

12 of 15


Electrical Works


9 Fire Alarm System

Supply, install and connect complete in place and in an

operable manner the addressable fire alarm system

BOSCH or equivalent including of the equipment

specified, installation of same connection, wiring

commissioning and all of the details as specified in the

technical specifications and drawing with complete

operation capacity 125 detectors.

9.1

Addressable main fire alarm control panel for 1 loop ,QS1

( QUICK START 1 )expandable including 24 hour backup

batteries and charger or equivalent.

Unit 1

9.2Addressable photo cell electric smoke detector (SIGA‐PS)

or equivalentUnit 35

9.3 Addressable heat detector (SIGA‐HRS) or equivalent Unit 10

9.4 Addressable break glass unit (SIGI‐271) or equivalent Unit 10

9.5 Indoor alarm siren (GIR‐P) or equivalent Unit 8

9.6 Outdoor alarm siren (757‐5A‐T) or equivalent Unit 1

9.7 Telephone dialer (DL‐125C) or equivalent Unit 1

Total of Fire Alarm System Works

10 Computer Network

10.1

Supply, install and connect , testing and commissioning

Rack cabinet 6U with patch panel 24 port, and 3COM

Baseline 24 PORT 10/100/1000 Switch or equivalent and

straight cables (CAT6 ) Shielded cable between switch

and patch panel and all necessary accessories with

complete operation.

No. 2

10.2

Supply, install, connect and programming Linksys

Wireless‐N Gigabit Security Router with VPN Secure, high‐

speed wireless networking or equivalent.

No. 2

Total of Computer Network

11Electronic private Automatic Branch Exchange (EPABX)

System

11.1

Supply, install, connect and test Panasonic KX‐TDA 100 ‐

8 line external and 24 line interior or equivalent ,the

price includes testing and commissioning works and all

accessories with complete operation .

NO 1

Total of Electronic private Automatic Branch Exchange

(EPABX) System

13 of 15


Electrical Works


12 Cable Trays

Supply and install cable trays, cable trunking and sleeves

as per drawings and specifications complete with

supports, fixing devices, covers, separators, clamps, end

caps, draw wires, elbows, joints, branches, reducers,

offsets …as show on drawings and specifications.

12.1LV Cable Tray 200x85 mm perforated galvanized iron,

1.5 mm thickness. (NIEDAX type or equivalent).M.L. 30

12.2Power Cable Tray 300x85mm perforated galvanized iron,

1.5 mm thickness. (NIEDAX type or equivalent).M.L. 40

Total of Cable Tray Works

13 Fire Fighting System

Supply install and connect complete in place and in an

operable manner the Fire Fighting system Telefire /Mircom / Kidde or equivalent For main distributionboard at electrical room . The work is to include thesupply of the equipment specified, installation ofsame connection, wiring commissioning and all ofthe details.

13.1

Automatic Valve Cylinder 3 Kg Kidde FM 200 P/ N 90100011001 ( 180 Degree Pendant Nozzle , 3/8" Check Valves , Bracket , Pressure Gauge , Copper pipe , Safe Cap …...with all accessories needed )

No. 1

13.2 Main Control Panel 2‐ Zone Telefire 2-B or equivalent No. 1

13.3Photoelectric Smoke Detector MIR-338H / TFO-440 or equivalent

No. 4

13.4 Heat detector ‐ S.S 5601 P / TFH-220F or equivalent No. 2

13.5 Indication lamp TFL-1N or equivalent No. 2

13.6 Break glass unit TPB-10 R or equivalent No. 1

13.7 Fire Indoor Horn TIP-224A or equivalent No. 1

Total of Fire Fighting System Works

14 of 15

1 Total of Main Feeder Works

2 Total of Electrical Switchboards Works

3 Total of Installation in the Building Points Works

4 Total of Lighting Fixtures Works

5 Total of Cables & Conductors / Leads Works

6 Total of Cable Conduit & Ducts Works

7 Total of low voltage box Works

8 Total of Grounding Works

9 Total of Fire Alarm System Works

10 Total of Computer Network Works

11Total of Electronic private Automatic Branch Exchange(EPABX) System

12 Total of Total of Cable Tray Works

13 Total of Total of Fire Fighting System Works

Total of Electrical works -including provisional items (Not Including Value Added Tax )


King Abdullah Bin Abdulaziz Technical & Vocational Training Center

Electrical Works

Electrical Summary

15 of 15

King Abdullah Bin Abdulaziz Technical & Vocational

Training Center

BOQ Landscaping works


Landscaping Works

Bill No. 1 Excavation and Earth Works

Item No

Description Unit QTY Price/

Unit Total

The Contractor shall when pricing the rates of this bill, take into consideration including and allow for the cost or expenses of all requirements stipulated in the preambles, drawings, and technical specifications. The words engineer below means owner's engineer. The rate include the following:

The contractor has to supply a Mesh Survey plan 5mX5m for the site from approved engineering surveyor before and after the works for quantities measurements .

The Contractor should present a soil investigation report from an approved Building laboratory as per engineering association requiments and standards on his own expenses.Excavation and backfilling for Working Space will not be measured .

In case and after the soil investigation report is done it was required to do more excavations, all excavations work will be carried over the bid unit price, the Contractor has no right for any kind of claims or any unit price change .

1.1

Cut in any kind of soil, concrete or stone walls to reduce level for foundation of retaining and boundary walls and foundation for security room, to reach the desired level(Hard Natural Rock)) according to drawings and site instructions .The price should include using and laying the approved fill material from site and or from outsite to reduce level and all test required to use the approved cut material for filling and watering ,compacting 100% each layer 20 cm and removing the unapproved excavated materials from the site to an approved dump location

m3 80

1.2

Supply and Lay selected & approved base coarse filling First class at 20cm layer to the required level ,watering and compacting 100% , the price include before basecoarse works ,filling approval fill below basecoarse layer ,watering and compaction 100%and where directed by the Engineer.

m2 380

1.3

Supply and install Asphalt layer 3/4'' thick=7cm the price include spread primer coat CO 1 1/2 kgr/m2 and all compaction testing for basecoarse and asphalt and as specification and as shown on drawings .

m2 150

Total of Bill No. 1

1 of 16


Landscaping Works

Item No


2 Concrete Works

The contractor shall, when pricing the rates of this bill, take into consideration including and allow for the costs or expenses of all requirements stipulated in the preambles, drawings and technical specification of the tender.

Each concrete pouring on site will be tested, pouring less than 6m3 will be tested, pouring more than 6m3 will also be tested on 6m3 portions i.e. each concrete truck on site will be tested, all done by an approved testing institute on contractors expense

The price should include cleaning all the foundation excavations, checking the sizes according to drawings, resizing if needed, cleaning, and installing wooden frame to marked the footings as instructed and approved by the site engineer

In case and after the soil investigation report is done, concrete quantities may vary,any Additional or less in bid quantities will be carried over the bid unit price, the Contractor has no right for any kind of claims or any unit price change .

2.1 PLAIN IN-SITU CONCRETE B200[200 Kg / CM2]

Supply & install Concrete B200 of 28 days cube crushing strength 200kg/cm2. Price shall include cleaning, compaction, shuttering and making good of ground surface before casting of concrete. Price shall include all nails, forms and equipments needed.

2.1.1 - Blinding under footing, ground beams thick 10cm m3 10


2 of 16


Landscaping Works

Item No



2.2 REINFORCED IN-SITU / READY MIXED CONCRETE

B300/ 300 Kg / CM2]

Supply & install concrete B300 of 28 days cube crushing strength 300kg/cm2. Price shall include the following:1. Cleaning and making good of surfaces before casting of concrete2. Steel reinforcement workmanship as per drawings.3. Form-work of any type or shape .4. Any materials such as nails, wires , 6mm steel for shuttering or any other material or workmanship needed for a best completion of the works .5. Installation of 2 cm thick. high density polystyrene on expansion joints.6. All steel reinforcement of any diameter and shape of high yield stress steel.7. Cube test 10x10x10cm and slump test before pouring any concrete on site, and vibration the concrete during casting . 8- isolation all buried parts using approved butimunies layer (hot or cold ) as per site engineer instructions and approval.

8.The measurement for slabs from the middle of the walls , and include all drop and inverted beams .

3 of 16


Landscaping Works

Item No



2.2.1Foundation of any shape, depth and size including retaining wall foundations, boundary wall and ground beam for security room footings , when pricing the

A- Check and report to the site engineer the situation of the excavation by an approved surveyorB- Clean the foundations excavations, and making good of any excavation if neededC- Resize the excavations to suit the design if there was any mistake in the excavation processD- Lay a wooden Works Frame Reference around the building to be referenced by an approved surveyor and approved by the site engineer.

m3 30

2.2.2For bearing retaining walls the price include the steel and scaffolding works from one side and as shown on drawings .

m3 100

2.2.3Ditto but for boundary walls the price include the steel and scaffolding and as shown on drawings .

m3 12

2.2.4

For security room reinforced Solid slab Thickness 15cm the price include scaffolding works and steel reinforcement and as shown on drawings and instructed by the site engineer

m2 11

2.2.5

Supply and install septic tank the price include excavation works to reduce level, concrete for blinding ,foundation ,wall and slab and steel reinforcement for all concrete element and all scaffolding works ,the price include also glanz plastering layer and two layers sika top from the inside walls and ceiling and precast Steel cover 25 ton as shown on drawings . all as instructed and approved by the site engineer

job 1

2.2.6

Supply and install plants bed size 1.0mX1.0m the price include excavation works to reduce level , concrete elements, steel reinforcement ,curbestone,plastering .agricultural soil and all scaffolding works and as shown on drawings .

job 17

2.2.7

Supply and install plants bed size 2.4mX0.90m the price include excavation works to reduce level , concrete elements, steel reinforcement , stone and coping ,plastering .agricultural soil and all scaffolding works and as shown on drawings .

job 4

Total of Bill No. 2

4 of 16


Landscaping Works

Item No


3 Stone Works

3.1 STONE BUILDING AND POINTING

The contractor shall, when pricing the rates of this bill, take into consideration including and allow for the costs and expenses of all requirements stipulated in the preambles, drawings and technical specification of the contract. The price includes the following:

All stone should be From Hebron area dark colour class A-A, بند ارضي, with the following specifications:


1. Steel anchors as specified.2. Flush pointing works composed of white cement and sand (1: 2) with approved additives for better workability, tightness and water proofing. 3. Ф8mm 20X20cm steel mesh reinforcement to be used for all stone concrete backing.4. Stone built shall be measured only " Net Measurements "


5 of 16


Landscaping Works

Item No



5. Each building stone must have at least two galvanized anchors from the top and to be fixed to the 3mm steel mesh.Similar stone can be either new stone or old stone from other sites. Both types must be supplied after the approval of the engineer.6. Acceptance of delivered stones should be carried by comparing every stone delivered on the truck to the sample built on site. All stones will be picked up and chosen by a specialist person (dresser) paid by the owner before using the stone.7. Rate includes and kind of stone dressing.8. Copping stones to be Mutabbeh finish for the horizontal surface and Taltish finish for the vertical

sides.

3.1.1

Supply and install 5 cm thick 25cm high TALTEESH stone courses for security room the price including all special pieces i.e. jams, lintels, sills and stone corners (at least 15cm deep), as shown on drawings. The price includes B200 concrete backing 20cm, anchors and steel reinforcement and glanz layer and block 7cm all as shown on drawings, instructed and approved by the site engineer .

m2 35

3.1.2Supply and build 5cm Thick stone copping width in any location as shown on drawings

m2 15

3.2 Stone Cladding

Supply, install stones cladding of excellent quality grade A-A " بند ارضي " with different thickness dressed Mulatash free from cracks. Rate for stone cladding shall include for:

All stone should be Herbron area dark colour class A-A, بند ارضي, with the following specifications:


6 of 16


Landscaping Works

Item No



1. Work for all classification in any location.2. Stone shall have a minimum thickness of 5cm after dressing with a rough back preferably.3. Stone built shall be measured only " Net Measurements "4. Stone sills and lintels of any kind shall be measured within the stone building and not separately

5. Corner and jambs stone of any kind shall be measured within the stone building and not separately6. Key stone and any other particular stone shall be measured within the stone building and not separately7. Price shall include concrete backing and Ф6 mm @ 20cm welded steel mesh and steel reinforcement for lintel beams.8. Stones with quality grade A-A (بند ارضي) shall be used only.9. Acceptance of delivered stones should be carried by comparing every stone delivered on the truck to the sample built on site. All stones will be picked up and chosen by a specialist person (dresser) paid by the owner before using the stone.10. Flush pointing works composed of white cement and sand (1: 2) with approved additives for better workability, tightness and water proofing.

3.2.1

Supply and install 5 cm thick 25cm high, stoneTaltish courses of first quality the price including all special pieces i.e. jams and lintels and stone corners, of depth not less than 25cm. The price includes 7-10cm thick B200 concrete backing,steel mesh and galvanized wire 3mm to tie the stone to the steel mesh as shown on drawings. The rate includes for walls and around columns and all special pieces . (Provisional Item)

m2 150

Total of Bill No. 3

7 of 16


Landscaping Works

Bill No. 4 Plastering Works

Item No


WALL PLASTERING

4 External Plaster (Provisional Item)


Prepare surfaces, apply a rendering coat (رشة مسمار),apply in two coats of rough and fine finish withordinary Portland cement , sand and lime asspecified. The price includes angle beads andmovement beads.

4.1

On walls 13mm thick external plaster (Shabrees)including patching works for any mechanical, electricalor civil works. Price should include supply and install stiwire mesh 200 mm wide , cloth mesh where required,All as per site engineer instructions .

m2 200

Total of Bill No. 4

8 of 16


Landscaping Works

Item No


5 Tiling WorksThe Contractor shall when pricing the rates of this bill, take into consideration including and allow for the cost or expenses of all requirements stipulated in the preambles, drawings, and technical specifications.Unit rate shall includes all designs and cutting as per drawings with no allowance for wasted tiles. Net engineering measurements on site for square meter will be considered.Unit rates for tiling works shall include the completion of works according to all details shown on drawings. The rate includes the pointing or grouting as specified, the crystal polish of terrazzo tiles.Tiling should be done using WHITE CEMENT only, even if not specified in the item

Terrazzo Tiles

5.1 Tiles

Supply and install the following class A irregular natural tiles with a pattern as per drawings. All bedded in , or backed with white cement and sand mortar (1:3) . The price shall include the supply and spreading of a layer of sand and Portland cement dry mixture under tiles and pointing with white cement thick 5cm and as shown on drawings .

5.1.1 To Floors m2 220

Bill No. 5 Flooring

9 of 16


Landscaping Works

Item No


Bill No. 5 Flooring

5.2 Stone Tiling1- All as per stone samples on site for colour, quality and shape.2- All stone tiles shall be free from cracks with quality grade A-A (بند ارضي) .3- Rates for tiles shall include for straight and curved cutting, waste, grouting and pointing to execute the works to the satisfaction of the Engineer.4- All stone tiles will be picked up and chosen by a specialist person (dresser) paid by the owner before using the stone - Absorption by weight should not exceed 0.9% using ASTM test method C97 - Density (Kg/m3) should not be less than 2700Kg/m3 using ATSM test method C97 - Compressive strength should not be less than 56MPa using ATSM test method C170 - Modulus of rupture should not be less than 6.9MPa using ATSM test method C99 - Abrasion resistance (hardness) should not be less than 10 using ATSM test method C241 - stone should be clear, free from all veins, cracks and salt holes from both sides

5.2.1

Supply and install approved natural stone polished for stair flight thick 3cm for tread and 2cm for riser the price include cement mortar under the stone and filling cement:sand 1:1 below the tiles the price include stone panels and skirting for water resist and as shown on drawings .

m.r. 25

5.2.2

Supply and install approved natural stone frame width 25 cm and thick 5cm between irregular tiles the price include cement mortar under the stone and filling cement:sand 1:1 below the tiles the price include and pointing 1cm and depth 2cm with white cement and as shown on drawings .

m.r. 80

Total of Bill No. 5

10 of 16


Landscaping Works

Bill No. 6 Water Proofing

Item No


6 Water Proofing (Security Room)


6.1

Supply and install 4 mm thick layers for top roof of modified bituminous membrane like Pazkar SBS 5/250 laid above two primer coats of GS474 at a rate of .25 kg /m2 or equivalent approved by the engineer on a clean surface of the roof tiling and around the parapets. The price includes supply and install sealant cover at groove" Sikaflex-pro 2HP or equivalent" . The price includes also supply and install 15*15cm angle fillet as shown in the drawings and painting the joints with "Silver PAZ". The application should be carried out in conformity with the manufacturers’ specifications and using propane torch welding only. the price include inclination concrete B-200 1% and the minimum thickness 5cm in near rain pipes .The measurement horizontal dimension .

m2 12

6.2

Supply and apply two coat of Sika Top Seal 107 or equivalent on a clean surface for the wet areas. The price includes 5*5cm angle fillet with smooth sand cement mortar (1:3) surface layer before applying the water proofing materials. The application should be carried out according to details and in conformity with the manufacturers’ specifications price include testing as instructed by the site engineer. The measurement horizontal dimension .

m2 10

Total of Bill No. 6

11 of 16


Landscaping Works

Item No


7 Metal Works


The rate for steel works includes the followingA. The submittal of shop drawings for the satisfaction of the Engineer prior to fabricating the units.B. The fabrication and installation of full scale model for part of metal works for inspection and approval of the Engineer before commencement of work.

7.1 ALUMINUM WORKS

Supply and install the following colored (powder coated, Migor'an) Dark gray Metallic color as per sample on site, Aluminum Mifromal Profile as made by NABCO wajhat Zojaj, as shown on drawings ( All hinges and handles have to be powder coated same color as aluminum

Price shall include laminated tempered glass 6/12/6mm , Ironmongery, fixing accessories original from Mifromal or Arpal such as rails, hinges, locks, brushes, rubber EPDM and angles must be original corresponding to each profile.Filling all sides and under the threshold and sills with SIKA FLEX 2H Pro color as of the aluminum color from out side and all exposed joints and MASTIC (NIRLAT made) from inside colored as the aluminum color All as instructed by the site engineer

Supply and install the followings ALUMINUM combinations NAPCO doors and windows 7700, as per drawings and specifications, all as instructed by the site engineer

7.1.1 windows for security room with overall dimensions as per drawings and Details.

m2 3

7.2 Steel Works


A. The submittal of shop drawings for the satisfaction of the Engineer prior to fabricating the units.


12 of 16


Landscaping Works

Item No



B. The fabrication and installation of full scale model for part of metal works for inspection and approval of the Engineer before commencement of work.C. cleaning of all steel profiles prior to commencement with painting layers as specified and shown in drawings.

D. Supply all kinds of material and apply two coats of APC antirust paint, and two coats of APC primer (ORANGE COLOR) Product Code: , drying period 3 days between each product

E. Supply all kinds of material and apply painting for steel, the price should include applying two coats of HAMMERITE paint with HAMMERITE dissolvent all as approved and instructed by the site engineer. The application should be carried out according to details and in conformity with the manufacturers’ specifications.

Supply and install the following steel doors, price to include cylinder, lock as made by WALLY, or approved eq., as a complete job,as shown on drawings.

7.2.1Door for security room with overall dimensions as shown on drawings

m2 3

7.2.2 Main external Entrance gate size 4X2.5m m2 10

7.2.3 Gate size 1.80X2.5m m2 5

7.2.4Supply and install metal protection bars for windows and as shown on drawings .

m2 3

Total of Bill No. 7

13 of 16


Landscaping Works

Item No



The contractor should allow in his pricing that the engineer will use as many different colours or combination of colours to meet an approved colour scheme. ( Company ready mix original)No hand made color mix is allowed.

The contractor has to prepare a color sample 1*1m on site for each color asked by the site engineer

All paint works should conform to Tambour instruction regarding number of coats , rate of application or drying time.

All protection and care should be taken against paint drips, drops, droplets, and brushing.

The contractor should study well the project, walls, ceilings, gypsum boards, and all finished surfaces before applying the paint, so that if he discovers any mistake or additional needed works, he shall inform the engineer so as to adjust and agreed upon additional items before signing of the contractor. Otherwise the contractor will be responsible and take no extra money for any change of order.


14 of 16


Landscaping Works

Item No



8 On Walls & Ceiling

8.1

Supply all kinds of raw material and apply paint Amulsion for security walls room ,and wherever needed or instructed by the site engineer, the price should include preparing surface, clean, remove dust and foregin matter, sanding with well with sand paper, checking the walls with putty, laying two coats of putty (APC brand or an approved equivalent), applying one coat of APC SUPER BOND ROLL and applying Four coats of APC Painting or equivelent Product, all as instructed and approved by the site engineer.

m2 40

8.2

Supply and apply Four coats of APC FILL Aracid Product ceilings over plastering, electrical, mechanical shafts, elevator shaft and wherever needed or instructed by the site engineer.

m2 15

Total of Bill No. 8

15 of 16


Landscaping Works


Excavation & Earth Works

Concrete Works

Stone Works

Plastering Works

Tiling Works

Water Proofing Works

Metal Works

Painting Works

Total of Civil Works (External works)-including provisional items(Not Including Value Added Tax )


Summary of Civil Works Bills 1 - 8

1

2

3

7

8

4

5

6

16 of 16



GRAND TOTAL SUMMARY SHEET


Total Summary

Summary Sheet


1 Summary of Civil Works Bills

2 Summary of Mechanical Works Bills

3 Summary of Electrical Works Bills

4 Summary of External works

Grand Total - including provisional items (Not Including Value Added Tax )


The Sum of (in words) :

Contractor:

Authorized Person Name & Title :

Signature & stamp:

Date:

Tel:

Mob:

Fax:

E-mail:

Address:

Final_Summary Page

Civil-Boq FINAL-.xlsx

Documents

Transcript of Civil-Boq FINAL-.xlsx