FINAL RATES QUOTEDSCHEDULE OF QUANTITYNAME OF WORK :- Construction of Residential Quarters 12 Nos. Type-C (G+2) & 32 Nos. Type-D (G+3) including water supply, Sanitary installation, Drainage and electric work etc. for Central University of Rajasthan at Bandar Sindri, Distt. AjmerS. No.Description of ItemQty.RateUnitAmountSUB HEAD-I : EARTH WORK1Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be leveled and neatly dressed(a)All kinds of soil200cum2Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed.(a)Ordinary rock50cum(b)Hard rock (blasting prohibited)40cum3Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(a)All kinds of soil.705cum4Excavation work by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains not exceeding1.5m in width or 10 sqm on plan including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m.(a)Ordinary rock422cum(b)Hard rock (blasting prohibited)280cum5Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :(a)All kinds of soil(i)Pipes, cables etc. exceeding 80 mm dia. but not exceeding300 mm dia.168.00metre6Filling available excavated earth /GSB/building rubbish in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.2273.00cum7Supplying and filling in plinth with Local sand under floors, including watering, ramming, consolidating and dressing complete.194.00cum8Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.(a)All kinds of soil.5280sqm6705.69Supplying and stacking of earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by20% for payment.)1568.00cumSUB HEAD-II : CEMENT CONCRETE10Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge.(a)All works upto plinth level.(i)M-10 grade plain cement concrete (cement content considered @ 220 kg/cum ).300.00cum(Note :- Nothing extra shall be paid for Cement content more than 220 kg/cum of concrete, if so, as per design mix. )11Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).246.00sqm12Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.246.00sqmSUB HEAD-III : RCC WORK13Centering and shuttering including strutting, propping etc. and removal of form for :(a)Foundations, footings, bases of columns, etc. for mass concrete880.00sqm(b)Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.780.00sqm(c)Suspended floors, roofs, landings, balconies and access platform.5645.00sqm(d)Shelves (Cast in situ)257sqm(e)Lintels, beams, plinth beams, girders, bressumers and cantilevers5030.00sqm(f)Columns, Pillars, Piers, Abutments, Posts and Struts5802sqm(g)Stairs, (excluding landings) except spiral-staircases238sqm(h)Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.642.00sqm(i)Weather shade, Chajja's, corbels etc., including edges160sqm14Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits.(a)50 mm thick40sqm15Providing and laying cement concrete 1:5:10 (1 Cement : 5Coarse sand : 10 Graded brick aggregate 40mm nominal size) up to floor five level for sunken floors etc excluding the cost of centering and shuttering.321.00cum16Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, by using miniumum 375 Kg. of cement per cum of concrete including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(Note :- Nothing extra shall be paid for Cement content more than 375 kg/cum of concrete, if so, as per design mix. )(a)All works up to plinth level400cum(b)All works above plinth level up to floor V level1960cum17Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.(a)Thermo-Mechanically Treated bars44000kg18Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.(a)Thermo-Mechanically Treated bars254800kg19Supplying and applying pre tested and approved water based concrete curing compound to concrete/ masonry surface, all as per manufacturers specification and direction of Engineer-in- charge.(a)Non pigmented wet curing compound2000kg20Providing, hoisting and fixing up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but excluding cost of reinforcement, with 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size).6.00cumSUB HEAD-IV :BRICK WORK21Brick work with common burnt clay F.P.S. (non modular)bricks of class designation 7.5 in foundation and plinth in:(a)Cement mortar 1:6 (1 cement : 6 coarse sand)726cum22P/L cellular light weight concrete blocks in superstructure of density 800-1000kg/cum and compressive strength 25kgs/cm2 manufactured using OPC cement,flyash,fine river sand and max. moisture absorption of 12-15% and pre-formed protein based foaming agent in super structure at all heights and levels in cement mortar 1:6 (1 cement : 6 coarse sand) in all shape and size.(a)Cement mortar 1:6 (1 cement : 6 coarse sand)1624cum23P/L cellular light weight concrete blocks in partation of 100 mm of density 800-1000kg/cum and compressive strength25kgs/cm2 manufactured using OPC cement,flyash,fine river sand and max. moisture absorption of 12-15% and pre-formed protein based foaming agent in super structure at all heights and levels in cement mortar 1:4 (1 cement : 4 coarse sand) in all shape and size.(a)Cement mortar 1:4 (1 cement : 4 coarse sand)4264sqmSUB HEAD-V :STONE WORK24Random rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with :(a)Cement mortar 1:6 (1 cement : 6 coarse sand)30cum(b)Cement mortar 1:6 (1 cement : 6 coarse sand)(Stone received from excavation will be used free of cost.)13.45cum4125Providing and fixing in Cement mortar 1:4 (1 cement : 4 coarse sand) double pitam (rebated) stone doors frame with necessary holes, of approved quarry, all exposed surface will be machine cut or fine dressed i/c holdfast etc. complete of size 125 x 65 mm,2850.00Metre26Stone work ashlar sunk or moulded or sunk and moulded upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade.(a)Red sand stone17cum27Stone tile work for wall lining upto 10 m height with special adhesive over 12mm thick bed of cement mortar 1:3 ( 1 cement: 3 coarse sand) including pointing in white cement with an admixture of pigment to match the stone shade.(a)8m thick (mirror polished and machine cut edge)100SqmGranite stone of any colour and shade28Providing and fixing stone jali 40mm thick throughout in cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc.(a)White sand stone215SqmSUB HEAD-VSUB HEAD-VI :MARBLE AND GRANITE WORK29Providing and fixing Lakha Red / Jet Black granite, 16mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.(a)Area of slab upto 0.50 sqm110sqm(b)Area of slab over 0.50 sqm290sqm30Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.368.00metre31Providing edge moulding to 16 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in Charge.(a)Granite work110metreSUB HEAD-VISUB HEAD-VII :WOOD AND PVC WORK32Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutter:(a)35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws762.00sqm33Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).762.00sqm34Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)(a)On one side only762sqm35Providing and fixing Fiber Glass Reinforced plastic (FRP) DoorFrames of cross-section 90mm x 45mm having single rebate of32mm x 15mm to receive shutter of 30mm thickness .The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat . Door frame laminate shall be2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.431.00mtr.36Providing and fixing to existing door frames.(a)30mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS:14856, complete as per direction of Engineer-in-charge.149.00sqm37Providing and fixing wire gauge shutters using Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both side for doors, windows and clerestory windows with hinges and necessary screws:(a)35 mm thick shutters.With ISI marked stainless steel butt hinges of required size(i)Second class teak wood.256sqm38Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.(a)Fixed to openings /wooden frames with rawl plugs screws etc9515Kg39Extra for Providing Polyester powder coated on M.S.grills (minimum thickness of polyester powder coating 50 micron) as per the direction of Engineer-in-Charge (Payment shall be made as per the actual weights of the M.S.grills9515.00Kg40Providing and fixing bright finished stainless steel sliding door bolts, transparent or dyed with nuts and screws etc. complete.(a)250 x 16mm460nos.41Providing and fixing bright finished stainless steel tower bolts(barrel type) with necessary screws etc. complete.(a)200 x 10mm455nos.(b)150 x 10mm455nos.42Providing and fixing bright finished stainless steel handles with necessary screws etc. complete.(a)125mm972nos.43Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate20mm nominal size)150.00nos.44Providing and Fixing, uPVC factory made, white colour casement/sliding window and door made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.5 0.2mm thick galvanised steel profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners and gap if any to be filled with sealing compound, all complete as per direction of Engineer-in-charge. (A dimensional tolerance of + 10% shall be permitted in the dimension of UPVC window profile / section)(Profiles, Glazing, hardware hinges and fitting etc. to be as per the detail narrated below:- )(a)Window Profiles: The profile section should be compatible for double glazing using high quality locking mechanism as per details below(i)Casement Frame (67mm x 62mm)(With friction hinge &outward opening)(ii)Casement Window Sash/Mullion (67mm x 75mm ) (style, rail and intermediate section)(iii)Casement Glazing bead (35mm x 18 mm)(b )HARDWARE : (i) stainless steel Friction hinges of size 300x19 x1.9 mm.(ii) casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.(iii) Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.(c)GLASS : Hermetically sealed double glass insulated unit of 24mm thickness using 6mm toughened glass on both sides and 12mm air gap with aluminium perforated spacers, desiccants, sealant (Both primary and secondary sealant) etc The double glazed glass shall be of high quality and in pristine white color of code PLTT of Saint Gobin or equivalent.865.00sqmSUB HEAD-VIII :STEEL WORKS45Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.9412.00kg46Providing and fixing 1mm thick M.S. sheet door with frame of40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces25sqm47Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.320.00nos.48Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete.144.00nos.49Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.(a)In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works500.00kg50Providing and fixing stainless steel ( Grade 304) railing as per enclosed Architectural drawing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).3245.00kgSUB HEAD-IX :FLOORING WORKS51Granite stone flooring with 16 mm thick granite stone over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white, mixed with matching pigment i/c rubbing & mirror polishing complete.Lakha red Granite/Z Black granite (Single piece used in staircase trade.)340.00sqm52Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.(a)40 mm thick with 20 mm nominal size stone aggregate40sqm53Cement plaster skirting up to 30 cm height, with cement mortar1:3 (1cement : 3 coarse sand), finished with a floating coat of neat cement.(a)18 mm thick18sqm54Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand)(a)25 mm thick52sqm55Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.25.00sqm56Providing and Laying Premium quality ceramic glazed wall tiles of size 12"x18" conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.1484.00sqm57Tile work in skirting, risers of steps and dado (up to 2 m height) over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.(a)Marble tiles (polished) Raj Nagar.(i)8 mm thick.372sqm58Marble stone flooring with 16 mm thick marble stone. ( sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :(a)Agaria White2876sqm(b)UDAIPUR GREEN MARBLE1557sqm5940mm thick rubbed stone flooring over 20 mm (average ) thick base of cement mortar 1:5 (1 cement :5coarse sand ) with joints3mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust )admixed with pigment to match the shade of stone and pointing the same mortar.(a)White sand stone.20sqm60Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm, including filling the gaps with ordinary cement mixture & mixing with synthetic polyester fibre, triangular in shape having specific gravity of 1.34 to 1.40, cross section size ranging from 10 to 40 micron & length upto 6 mm , mixing fibre @ 125 grams per 50 kg of cement in cement mortar, including providing and mixing water proofing material in mortar @ 1 kg per 50 kg of cement , all complete as per direction of Engineer-in-charge.1427.00sqm61Providing and laying rectified anti-skid Ceramic glazed floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), including grouting the joints with white cement and matching pigment etc., complete. (The tile shall have minimum abrasion value of grade -4).729.00sqmSUB HEAD-X :ROOFING WORKS62Providing and laying roof insulation with 75 mm thick impervious, sprayed, C F C free closed cell free Rigid polyurethane foam with thermal conductivity not more than0.028W/m/K at 10 degree C mean temperature and having additional properties of compressive strength not less than300KPa and 7 days water absorption not more than 0.2 kg/cum and minimum value of CFC free closed cell contents at 92% by volume over deck insulation confirming to IS - 12432 Pt III (density of foam being 40-45 kg/cum) over a coat of polyurethane primer applied @ 6-8 sqm per liter, laying 400 G polythene sheet over PUF spray and providing a wearing course of 40 mm thick cement screed 1 : 2 : 4 (1cement : 2 coarse sand: 4 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the joints with polymerized mastic all complete as per direction of Engineer-in-charge.1475.00sqm63Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.(a)2mm thick flat50sqmSUB HEAD-XI : FINISHING646 mm cement plaster of mix :(a)1:3 (1 cement : 3 fine sand)5252sqm6512 mm cement plaster of mix :(a)1:4 (1cement:4 coarse sand)200sqm(b)1:6 (1 cement: 6 coarse sand)20712sqm6620mm thick cement plaster of mix.(a)1:6 (1 cement: 6 coarse sand)400sqm67White washing with lime to give an even shade :(a)New work (three or more coats)239sqm68Finishing walls with water proofing cement paint of required shade :(a)New work (Two or more coats applied @ 3.84 kg/10 sqm)600sqm69Finishing walls with textured exterior paint of required shade :(a)New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @2.20kg/10 sqm8418.00sqm70Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade :(a)New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)200.00sqm71French sprit polish: Two or more coats on new works including a coats of wood filler.1087.00sqm72melamine polishing on wood work (one or more coats)1000sqm73Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.25964.00sqm74Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/liter of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.(a)Two coats20780sqm75Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.(a)Two coats590sqm76Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.(a)With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ liter1562.00sqm(b)With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/liter400.00sqm7715mm thick sand stone tile lining at all heights and levels with special adhesive such as H-40 Eco Extra Flex of Kerakoll or equivalent. Adhesive layer shall be minimum 5mm thick and done through approved applicator trained by manufacturer. Stone tile shall be fixed with adhesive over 12mm cement plaster 1:3 ( 1 cement : 3 coarse sand) and pointing with suitable material with admixture of pigment to match the stone shade all complete as per directions of Engineer in Charge. Size of stone shall not be more than 1.5 sqft.a)First quality Gang saw cut white Dholpur sand stone (natural)7418sqmb)First quality Gang saw cut white Dholpur sand stone (honed finish)1000.00sqm78Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :(a)New work (two or more coats) over and including water thinnable priming coat with cement primer600.00sqmSUB HEAD-XII : ROAD WORK79Providing and erecting 3.00 metre high (1.2m at Bottom with CGI sheet & top 1.8m with good quality Hessian / Woven Plastic / Geotextile) temporary barricading at site as per drawing/ direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. (Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on660.00metreShifting of barricading shall be done free of cost in accordance with the exigencies of work if shifting is done for any other reasons, the same shall be paid for separately.)SUB HEAD-XIII : ALUMINIUM WORK80Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make confirming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :(a)For Fixed Portion:-(i)Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)4800.00kg(a)For shutters of doors, windows and ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)(i)Polyester Powder Coated aluminium (minimum thickness of polyester powder coating 50 micron).6950.00kg81Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket/with putty etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):(a)With float glass panes of 5.50 mm thickness40sqm82Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.(a)Up to 5mm depth and 5 mm width993metre83Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :(a)100 mm500nos.84Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS :1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :(a)150x10 mm1000nos.85Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with nuts & bolts complete.(a)Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and1.4 mm aperture on both sides.690.00sqmSUB HEAD-XIV : WATERPROOFING WORK86Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of :i)Ist course of applying cement slurry @ 4.4Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.ii)IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.iii)IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg. per sqm of area.iv)IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.)1172.00sqm87Providing & Applying to layers of tape- crete over R.C.C surface as per manufacturer specification duly approved by Engineer-In-charge.1172.00sqmSUB HEAD XV : MISCELLANEOUS88Providing and fixing extruded polystyrene Insuboard XPS (density not less than 36 kg/cum 2 kg/cum, compressive strength not less than 276 kpa, water absorption not more than0.3% V/V and thermal conductivity not more than 0.028W/mK) manufactured by M/s Supreme Petrochem Ltd / DOW Chemicals / Isofoam or equivalent of thickness 50mm in vertical walls / expansion joints of required size etc. complete as per manufacture's specification as approved by competent authority and as per direction of Engineer-in-charge.2021.00sqm89Making plinth protection using 40mm thick fine dressed sand stone flooring over 20 mm (average) thick base of cement mortar 1:5 including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of matching pigment laid over under layer of 75 mm thick 1:5:10(1 cement :5 coarse sand :10 graded stone 40mm thick) all complete as per direction of Engineer in charge(a)Red sand stone270Sqm90Stone chap/path edging to plinth protection 40 to 50 mm wide30 cm deep with approximate rectangular shape rough dressed chaps (Bijolia Sandstone) jointed with Cement motor 1:4 (1 cement :4 fine sand) and as per the direction of Engineer in Charge including excavation refilling and disposed of surplus earth up to 50m lead complete.489.00MetreSUB HEAD XVI : SANITARY INSTALLATION91Providing and fixing water closet squatting pan (Indian type W.C. pan ) with long arm Centrifugally cast Iron P or S trap, Dual flush low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :(a)White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.44.00Nos.92Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, Dual flush low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231 with all fittings and fixturescomplete including cutting and making good the walls and floors wherever required:(a)W.C. pan with ISI marked white solid plastic seat cover and lid.44Nos.93Providing and fixing C.P. jet for European44Nos.94Providing and fixing white vitreous china ( continental sereis code no. CNS-WHT-WB 03 size 560x450x175 mm of Jaquar make) or equivalent under counter wash basin with C.I brackets, 32 mm dia C.P brass waste of standard pattern, including painting , of fitting and brackets, cutting and making good the wall where ever required.(a)Oval wash basin Size 560 x 450 x175 mm88Nos.95Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe(i)32 mm dia88Nos.(ii)40 mm dia44Nos.96Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.88.00Nos.97Providing and fixing stainless steel A ISI 304 (18/8) Kitchen Sink as per IS 13983 with C.I. brackets and stainless steel plug 40mm including painting of fitting and brackets, cutting and making good the walls wherever required.(a)Kitchen sink with drain board 510 x 1040 x 178 mm depth44Nos.98Providing and fixing soil, waste, rain water and vent pipes :(a)100 mm dia.(i)Centrifugally cast (spun) iron socketed pipe as per IS: 3989.3320metre99Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. :(a)For 100 mm dia. Pipe500Nos.100Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.(a)100 mm(i)Sand cast iron S&S as per IS - 3989152Nos.101Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.(a)100x100x100mm(i)Sand cast iron S&S as per IS - 3989100Nos.102Providing and fixing heel rest sanitary bend(a)100 mm(i)Sand cast iron S&S as per IS - 398968Nos.103Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete :(a)100x100x100x100mm(i)Sand cast iron S&S as per IS - 398990Nos.104Providing and fixing terminal guard:(a)100 mm(i)Sand cast iron S&S as per IS 398968Nos.105Providing and fixing collar:(a)100 mm(i)Sand cast iron S&S as per IS 398994Nos.106Providing lead caulked joints to sand cast iron/centrifugally cast(spun) iron pipes and fittings of diameter:(a)100 mm1700Nos.107Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter :(a)100 mm82Nos.108Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :(a)100 mm inlet and 100 mm outlet(i)Sand cast iron S&S as per IS: 3989.180Nos.109Providing and fixing C.P brass towel ring ( kubix series code AQN-7721 of Jaquar make) or equivalent with cocealed fitting arrangement of approved color etc all complete144.00Nos.110Providing and fixing C.P soap Dish Holder ( kubix series code AKB35731 of Jaquar make) or equivalent with cocealed fitting arrangement of approved color etc all complete192.00Nos.111Providing & Fixing chrome plated over head shower ( Multy function shower code OHS - 1789, 120 mm dia of jaquar make or equivalent and shower arm, code SHA 487-120mm long of jaquar make etc. all complete88.00Nos.112Providing and fixing low flow basin mixture ( Jaquar - FLR5167NB) or equivalent with concealed fitting arrangement etc. all complete.88.00Nos.Sub Head-XVII : WATER SUPPLY113Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work Exposed on wall, Terrace etc.(a)15 mm dia. nominal bore355metre(b)32 mm dia. nominal bore330metre(c)40 mm dia. nominal bore430metre(d)50 mm dia. nominal bore330metre114Providing and fixing chlorinated polyvineyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain & brass threaded fittings, fixing the pipe with clamps at1.00 mm spacing. The includes jointing of pipes & fittings with one step CPVC gidrent cement and cost of cutting chases and making good the same including testing of joints. ( Concealed work including cuttimg and making good the walls etc.)(a)15 mm dia nominalouter dia pipes750metre(b)20 mm dia nominalouter dia pipes550metre(c)25 mm dia nominalouter dia pipes550metre(d)32 mm dia nominalouter dia pipes730metre115Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work(a)40 mm dia. nominal bore550metre(b)50 mm dia. nominal bore550metre116Providing and fixing water saving bib cock straight line or anguler shape ( Florentine series code FLR-5047N or FLR - 5037 respectively of jaquar make or equivalent including flange etc, complete all respects.(a)15 mm nominal bore.136Nos.117Providing and fixing chrome plated anglular valve for WB & Gayser(a)15mm nominal bore352Nos.118Providing and fixing CP brass long body bib cock of approved quality conforming to IS standard and weighting not less than 690 gms(a)15 mm nominal bore56Nos.119Painting G.I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work :(a)32 mm diameter pipe.350metre(b)40 mm diameter pipe.450metre(c)50 mm diameter pipe.350metre120Providing and filling sand of grading zone V or coarser grade allround the G.I. pipes in external work.(a)40 mm diameter pipe.550metre(b)50 mm diameter pipe.550metre121Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)(a)32 mm nominal160Nos.(b)40 mm nominal bore140Nos.(c)50mm nominal bore40Nos.122Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :(a)25 mm nominal bore.64Nos.(b)32 mm nominal bore.16Nos.123Providing and fixing uplasticised PVC connection pipe with brass unions :(a)45 cm length(i)15 mm nominal bore204Nos.124Providing and placing on terrace (at all floor levels) polyethylene water storage tank with seven layers ISI: 12701 marked with cover and suitable locking locking arrangement and making necessary holes for inlet, outlet and overflo pipe bent without fittin and the base support for tank.44000.00Litre125Providing and fixing brass / ferrule connection with month cover including boring and taping the main(a)20 mm nominal bore8Nos.126Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat ceemnt complete as per standard design:(a)With common burnt clay F.P.S. ( non modular) bricks of class designation 7.58.00Nos.Sub Head-XVIII : DRAINAGE127Providing, laying and jointing glazed stoneware pipes grade A with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :(a)100 mm diameter72metre(b)150 mm diameter740metre128Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design:(a)100 mm diameter S.W. pipe72metre(b)150 mm diameter S.W. pipe740metre129Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :(a)250 mm dia. R.C.C. pipe580metre(b)300 mm dia. R.C.C. pipe478metre130Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :(a)Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :(i)With Sewer bricks conforming to IS : 488536Nos.131Extra for depth for manholes(a)Size 90x80 cm(i)With Sewer bricks conforming to IS : 48856metre132Providing and fixing square-mouth S.W. gully trap grade 'A' complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :(a)150 x 100 mm size P type.(i)With sewer bricks conforming to IS : 488522Nos.133Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand ) with pre-cast R.C.C. vertical grating complete as per standard design :(a)with common burnt clay F.P.S. Bricks25Nos.134Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame and vertical grating complete as per standard design :(a)with common burnt clay4Nos.135Providing and laying S & S centrifugally cost (spun) iron pipe (classLA) conforming to I.S. 1536(a)100 mm dia pipe60MetreTotal (A) Civil WorkESTIMATED COST AS PER NIT (CIVIL)3.65% ABOVE ON ESTIMATED COST(B)ELECTRICAL WORKSUB-HEAD I : INTERNAL WIRING1Wiring for Light point / Fan point / Exhaust Fan point / Call Bell point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.a)Group - A1738Point2Wiring for Light point / Fan point / Exhaust Fan point / Call Bell point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. (Point shall be controlled / looped from existing point-Group control point wiring).52Point3Wiring for light/power plug with 2 x 4 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit alongwith 1 No. 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.3420Metre4Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing3 pin 5 / 6 amps modular socket outlet and 5 / 6 amps modular switch, connection, painting etc.as required. (For light plugs to be used in non residential buildings)560nos.5Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing6 pin 15/16 & 5/6amps modular socket outlet and 15 / 16 amps modular switch, connection, painting etc.as required.228nos.6Wiring for circuit / submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed steel conduit as required.a)2 X 1.5 sq. mm. + 1 X 1.5 sq. mm. Earth wire2800Metreb)2 X 2.5 sq. mm. + 1 X 2.5 sq. mm. Earth wire3750Metrec)4 X 2.5 sq. mm. + 2 X 2.5 sq. mm. Earth wire660Metred)4 X 4 sq. mm. + 2 X 4 sq. mm. Earth wire660Metree)2 X 6 sq. mm. + 1 X 6 sq. mm. Earth wire1980Metref)2 X 10 sq. mm. + 1 X 10 sq. mm. Earth wire640Metreg)4 X 10 sq. mm. + 2 X 10 sq. mm. Earth wire280Metre7Supplying and fixing 25 Amps Power Unit surface/recess type for Air-Conditioners, 240 Volts, Modular type, Socket outlet, along with moror starter for protection from Overloads, GI box, modular base & cover plate, plug top with indicator etc complete with connections, testing and commissioning etc. as required.132nos.8Supplying and fixing of following sizes of steel conduit along with the accessories in surface / recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.a)25 mm (For TV, Telephone, Fire Alarm System, Wi-Fi system)2700Metreb)32 mm88Metre9Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduitas required.(a)25 mm2700Metre(b)32 mm88Metre10Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.306nos.11Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.(a)1 or 2 Module (75mm x 75mm ) for TV & Telephone Socket264nos.(b)6 Module (200mm x 75mm )44nos.12Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.a)15/16 amps switch44nos.b)3 pin 5/6 amp socket outlet88nos.c)Telephone socket outlet132nos.d)TV antenna socket outlet132nos.e)Lan Cable Socket outlet for cat-6 cable44nos.13S/D of Cat-6 data cable in the exisiting surface / recessed PVC/steel c740Metre14Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed / PVC conduit as required.a)2 Pair2820Metre15Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.2820Metre16Supplying and fixing Ding Dong call bell suitable for single phase,230 volts, complete as required.44nos.17Supply & fixing of 20 pair telephone tag (Krone make) block with required size box with lockable cover.2nos.18Supply & fixing of 50 pair telephone tag (Krone make) block with required size box with lockable cover.2nos.SUB-HEAD II : DISTRIBUTION BOARDS & PANELS1Supplying and fixing following ways surface/ recess mounting,vertical type, 415 volts, TPN MCB distribution board of sheetsteel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's, with provision of 100 amps TP 16 KA MCCB asincomer, interconnection between incomer MCCB and bus bars(but without MCB's/ MCCB) as required. (Note: Vertical typeMCB TPDB is normally used where 3 phase outlets are required)a)4 WAY (4+12), Double Door4Nos.2Providing and fixing following rating and breaking capacity four pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.a)100 Amp, 16 KA4Nos.3Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)a)8 WAY (4+8), Double Door32nos.b)12 WAY (4+12), Double Door32nos.3Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)a) 4 WAY (4+12), Double Door24nos.4Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 'C' curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.a)Single pole940Nos.b)Triple pole12Nos.5Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.(a)40 amps64Nos.6Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.(a)40 amps24Nos.7Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.(a)40 amps24No.8Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.a)25 amps32nos.b)40 amps32nos.9Supplying, installation, testing and commissioning of cubical tube compartmentalized meter board made of 1.6mm thick sheet steel duly powder coated, integrated loose wire box, complete with incomer125A, 16 KA 4Pole, Microprocessor release, MCCB, 200Amp. insulated copper Bus Bars, each meter compartment having 40Amp. TP MCB, space for meter, pre-wired from Bus-bar upto connector block (for each quarter), in loose wire box, compartment for digital ammeter, Digital voltmeter, Selector Switch for Ammeter and voltmeter including supplying and fixing of all material, locking/ ceiling arrangement for each. The area of meter board shall not be less than 2.25 Sq.mtr. and fixing of all material 300mm deep.Suitable for 8Nos, 1 Kwh Meters12Sets10Supplying, installation, testing and commissioning of electronic kwh meter, sleek model with current reversal indication, LED indication proportional to kwh for on-spot calibration, dust proof body, rugged construction, elegant poycarbonate casing, non affected by external magnetic field energy meters, three phase energy meter works even on neutral removing etc. complete as required as per spesifications.a)3Phase, 4 Wire, kWh, 10 -40A Sleek12Nos.b)1Phase, LCD Meter 5-30A with optical port32Nos.c)1Phase, LCD Meter 10-60A with optical port32Nos.SUB-HEAD III : LIGHTNING PROTECTION1Earthing with G.I. earth pipe 4.5m long x 40mm dia. including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt complete as required.16Sets2Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.4Nos.3Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.40Nos.4Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)600Metre5Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)220Metre6Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.16Nos.7Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.80MetreSUB-HEAD IV : EARTHING1Earthing with G.I. earth pipe 4.5m long x 40mm dia. including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt complete as required.24Sets2Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.120Sets3Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.120MetreSUB-HEAD V : FANS & LIGHTING FIXTURE1Supply, installation, testing and commissioning of pre-wired, 1x28W fluorescent luminaire surface type with electronic (HFP) ballast, CRCA body slim looks, including 1xTL5-28W Lamp, lockable holders etc. complete as required, Similar to PHILIPS Cat. Ref. No. MIROLTA Slim T5 TMS540 HF/ TRILUX Ridos 40128 ( without diffuser) GE DMS 28 DN /Blue and caps Make.100Nos.2Supply, installation, testing and commissioning of pre-wired, 1x14W fluorescent luminaire surface type with electronic (HFP) ballast, CRCA body slim looks, non-corrosive, robust including 1xTL5-14W Lamp, lockable holders etc. complete as required, Similar to PHILIPS Cat. Ref. No. ADRENO V 14W TWG207/ TRILUX Ridos 40114 ( with diffuser) GE DMS 14 DN/ Decon Make.88Nos.3Supply, installation, testing and commissioning of 1x20W pendent light luminaire complete with lockable holder, lamp etc complete as required, Similar to PHILIPS Cat. Ref. No. FXC 101 1xPL-S 9W AC GR/ KBH 9W CFL/ Crompton Cat. Ref. No. QPG 302/ GE- CPL11x10 VH/ TRILUX/ Decon Make.44Nos.4Supply, installation, testing and commissioning of 1x12W water resistant IP44 light luminaire including 1x12W Tornado Lamp, E27 lamp Base etc complete as required, Similar to PHILIPS Cat. Ref. No. 71165/30/ Decon/ GE Make.12Nos.5Supply, installation, testing and commissioning of surface mounted2xPLC 18W cylindrical Downlight, including 2xPLC 18W Lamp, electronic gear, high efficiency glossy reflector, CRCA Housing etc complete as required similar to PHILIPS Cat. Ref. No. FCS 105/218HF/ TRILUX Onperla D2 HR 2TCT 18-01/ REGENT 3030 W. P218.7/ Schreder/ Decon Make.224Nos.6Supply, installation, testing and commissioning of water resistant IP44 rating, 1x12W CFL luminaire surface type with ballast, glass, stee housing, including 1x12W Tornado Lamp, E27 Lamp base etc. complete as required, Similar to PHILIPS Cat. Ref. No.32081/31/Decon/ Schreder/GE Make.352Nos.7Supply, installation, testing and commissioning of wall mounted,1x12W CFL luminaire with ballast, glass, stee housing, including1x12W Tornado Lamp, E27 Lamp base etc. complete as required, Similar to PHILIPS Cat. Ref. No. QWG 305/ Schreder/ Trilux/ decon Make.296Nos.8Supply, installation, testing and commissioning of wall mounted,1x23W CFL luminaire with ballast, glass, stee housing, including1x12W Essential E27 Lamp base etc. complete as required, Similar to PHILIPS Cat. Ref. No. QWG 311/ Antracile/Trilux/ Schreder/ Decon Make.72Nos.9Supply, installation, testing and commissioning of 1200 mm sweep,50W, 350RPM, Air Delivery 225 CMM, Energy Saving ceiling fan complete with double ball bearings, blades, down rod, shackle insulator, canopy etc. complete as required, Similar to Havells Cat. Ref. No. ES 5/ Crompton Greaves/Almonard/ Marathon Electric Make.188Nos.10Supply, installation, testing and commissioning of 900 mm sweep,50W, 350RPM, Air Delivery 225 CMM, Energy Saving ceiling fan complete with double ball bearings, blades, down rod, shackle insulator, canopy etc. complete as required, Similar to Havells Cat. Ref. No. SS 290/ Crompton Greaves/Almonard/ Marathon Electric Make.132Nos.11Supply, installation, testing and commissioning of havy duty,230Volts, single phase, 50Hz, 300mm dia exhaust fan double ball bearing,complete with enegy efficent motor, louvers, bird screen and with 3 core flexible wire complete as required, similar to Havells cat. ref. no. TURBO FORCE/ Crompton Greaves/Almonard/ Marathon Electric Make.156Nos.ABOVE 3.65%OF ESTIMATED COST0