Thiele Grade 80 Alloy Chain - Schillings

06/0

7

Thiele Grade 80Alloy Chain

The following are our recommendations:

ACIDIC CONDITIONS:

Alloy Grade 80 slings should not be used in acidic or lyes solutions nor in anyother corrosive environment.

TEMPERATURE CONDITIONS:

-30°C to 200°C no reduction in W.L.L.200°C up to 300° Reduce W.L.L. by 10%300°C up to 400° Reduce W.L.L. by 25%Do not use above 400°

GALVANISING

Alloy chains and fittings should not be hot-dip galvanised nor electro-plated.Galvanised slings must always have the Working Load Limit reduced by 20%.Galvanising should only be done after consultation with the manufacturer.

Maximum Safe Working Loads in Tonnes of 1000kg under general condition of use.• DO NOT EXCEED SAFE WORKING LOAD• DO NOT EXCEED 120°• W.L.L. at 60° must never be exceeded, even at smaller angles.• W.L.L. at other angles - may be interpolated between the loads shown

at 60° and 120°• Flexible loads, above ratings must not be exceeded even if the load

is flexible

IMPORTANT INSTRUCTIONS ON THE USE OF ALLOY GRADE 80

CHAIN SLINGS.

SAFETY WARNING OF HAZARDOUS CONDITIONS:

Extreme care should be taken when using the Grade 80 Chain Slings in closeproximity of high temperature.It is therefore recommended that the user must always choose to err on theside of safety and make ample provisions for reduced Working Load Limits.

Chain Chain dia. Pitch Inside Outside width Working Weight

Size Width Load Limit app.

mm d tol. p tol. w1 min w2 w2 max tonnes kg

6-8 6.00 0.2 18.00 0.5 8.00 21.0 21.6 1.12 0.8

7-8 7.20 0.2 21.80 0.6 9.45 24.5 25.2 1.50 1.1

8-8 8.00 0.3 24.00 0.7 10.80 28.0 28.8 2.00 1.4

10-8 10.00 0.4 30.00 0.9 13.50 35.0 36.0 3.15 2.2

13-8 13.00 0.5 39.00 1.0 17.50 45.5 46.8 5.30 3.8

16-8 16.00 0.6 48.00 1.4 21.50 56.6 57.6 8.00 5.7

18-8 18.00 0.9 54.00 1.6 24.30 63.0 64.8 10.00 7.3

20-8 20.00 1.0 60.00 1.8 27.00 70.0 72.0 12.50 10.9

22-8 22.00 1.1 66.00 2.0 29.50 77.0 79.2 15.00 10.9

26-8 26.00 1.3 78.00 2.3 35.00 91.0 93.6 21.20 15.2

28-8 28.00 1.4 84.00 2.5 37.80 98.0 100.8 25.00 17.6

32-8 32.00 1.6 96.00 2.9 43.20 112.0 115.0 31.50 23.0

dw1

p

w2

23

Chain dia. Single Leg Slings Slings of 2, 3 or 4 Legs Endless Slings

Adjustable Reeved Straight Sling Reeved Sling Basket Slingmm Sling Sling

06/0

7

Single Leg Chain Sling c/w Oblong Links

Two Leg Chain Slingwith Sling Hooks

Endless Chain Sling

Two Leg Endless Chain Sling

Single Leg Chain Slingc/w Sling Hook & Shortener

Four Leg Chain Slingwith Sling Hooks

ReevedSling

Alloy Grade 80 Chain Sling Load Chart

6 1.1 0.8 0.8 1.9 1.6 1.1 1.5 1.2 0.8 1.5 1.2 0.8 1.7

7 1.5 1.1 1.1 2.6 2.1 1.5 2.0 1.6 1.1 2.0 1.6 1.1 2.3

8 2.0 1.5 1.5 3.5 2.8 2.0 2.6 2.1 1.5 2.6 2.1 1.5 3.0

10 3.2 2.4 2.4 5.5 4.5 3.2 4.1 3.4 2.4 4.1 3.4 2.4 4.8

13 5.3 4.0 4.0 9.2 7.5 5.3 6.9 5.6 4.0 6.9 5.6 4.0 8.0

16 8.0 6.0 6.0 13.8 11.3 8.0 10.4 8.5 6.0 10.4 8.5 6.0 12.0

20 12.5 9.4 9.4 21.6 17.6 12.5 16.3 13.3 9.4 16.3 13.3 9.4 18.8

22 15.0 11.3 11.3 26.0 21.2 15.0 19.5 15.9 11.3 19.5 15.9 11.3 22.5

26 21.2 15.9 15.9 36.7 29.9 21.2 27.6 22.5 15.9 27.6 22.5 15.9 31.8

32 31.5 23.6 23.6 54.5 44.4 31.5 41.0 33.4 23.6 41.0 33.4 23.6 47.3

60° 90° 120° 60° 90° 120° 60° 90° 120°

Straight Slingor adjustable

Sling with no deration (Refer Notes)

To AS/NZS 3775 SAFETY FACTOR OF 4

Sling Type Examples

24

06/0

7

Thiele Grade 80 Alloy ComponentsTWN 0831 Oblong Master Link Type A for Single Leg Slings

Trade Chain Working Dimensions in mm Weight

Size Diameter Load Limit app.

mm mm tonnes D F B kg

6-8 6 1.60 13 110 60 0.348-8 8 2.80 18 135 75 0.8310-8 10 4.25 22 160 90 1.5013-8 13 7.50 26 180 100 2.3316-8 16 11.20 32 200 110 4.0018-8 18 14.00 36 260 140 6.3020-8 20 17.00 40 300 160 9.0022-8 22 21.20 45 340 180 12.0026-8 26 30.00 50 350 190 17.0028-8 28 33.50 50 350 190 17.0032-8 32 45.00 56 400 200 23.0036-8 36 56.00 63 430 220 32.0040-8 40 71.00 71 460 250 44.0045-8 45 90.00 80 500 270 62.0050-8 50 112.00 90 500 270 79.0056-8 56 140.00 100 550 300 108.00

TWN 0832 Oblong Master Link Type A for Double Leg Slings

Complies to AS/NZS 3775

25



mm mm tonnes D F B kg

6-8 6 1.12 13 110 60 0.348-8 8 2.00 16 110 60 0.5310-8 10 3.15 18 135 75 0.8313-8 13 5.30 22 160 90 1.5016-8 16 8.00 26 180 100 2.3318-8 18 10.00 32 200 110 4.0020-8 20 12.50 32 200 110 6.3022-8 22 15.00 40 300 160 10.2026-8 26 21.20 45 340 180 12.0028-8 28 25.00 45 340 180 12.0032-8 32 31.50 50 350 190 17.0036-8 36 40.00 56 400 200 23.0040-8 40 50.00 63 430 220 32.0045-8 45 63.00 71 460 250 44.0050-8 50 80.00 80 500 270 62.0056-8 56 100.00 90 500 270 79.00



mm mm tonnes E G A C kg

6-8 6 1.12 43 17 59 45 0.097-8 7 1.50 56 17 75 47 0.168-8 8 2.00 60 18 79 50 0.1910-8 10 3.15 75 22 99 63 0.3513-8 13 5.30 98 28 128 80 0.7316-8 16 8.00 110 33 148 98 1.3818-8 18 10.00 122 36 165 110 1.8620-8 20 12.50 134 45 185 122 2.3422-8 22 15.00 145 44 198 132 3.1626-8 26 21.20 164 55 225 156 5.0032-8 32 31.50 192 65 268 192 9.33

06/0

7

Thiele Grade 80 Alloy Components

TWN 0829 THI-LOK Connecting Link

TWN 0798 Self Locking Eye Hook



mm mm tonnes E D G H C kg

6-8 6 1.12 106 22.5 28 22 15 0.487/8-8 8 2.00 133 24 35 25 20 0.8210-8 10 3.15 167 32 45 35 27 1.6513-8 13 5.30 208 39 54 41 33 3.1216-8 16 8.00 250 49 67 54 39 5.88

18/20-8 18/20 12.50 275 66 78 53 56 7.8022-8 22 15.00 317 71 94 72 58 15.00

TWN 0833 Master Link Assembly for 3 & 4 Leg Slings



mm mm tonnes E D F B D1 F1 B1 kg

6-8 6 2.36 189 18 135 75 13 54 25 1.208-8 8 4.25 230 22 160 90 16 70 34 2.2010-8 10 6.70 265 26 180 100 18 85 40 3.4013-8 13 11.20 315 32 200 110 22 115 50 6.1016-8 16 17.00 400 36 260 140 26 140 65 10.0018-8 18 21.20 490 45 340 180 32 150 70 18.0020-8 20 26.50 500 50 350 190 32 150 70 23.0022-8 22 31.50 520 50 350 190 36 170 75 25.0026-8 26 45.00 570 56 400 200 40 170 80 34.0028-8 28 50.00 610 63 430 220 45 180 90 47.0032-8 32 67.00 660 71 460 250 50 200 100 65.0036-8 36 85.00 750 80 500 270 63 250 125 102.0040-8 40 106.00 750 90 500 270 63 250 125 121.0045-8 45 132.00 830 100 550 300 71 280 140 167.0050-8 50 170.00 830 112 550 350 75 280 140 209.0056-8 56 212.00 970 125 650 400 85 320 160 304.00


26

06/0

7




mm mm tonnes E G H C F B kg

0.75-8m - 0.75 113.5 19 14 13 25 30 0.366-8 6 1.12 113 18 20 14 25 30 0.388-8 8 2.00 155 21 25 19 42 44 1.0010-8 10 3.15 162 23 30 21 42 44 1.2013-8 13 5.30 190 32 33 28 43 51 2.0816-8 16 8.00 247 40 43 35 61 64 4.45

TWN 0854 Swivel Hook with Safety Latch



mm mm tonnes E D1 D2 G H C kg

6-8 6 1.12 91 21 11 23 17 16 0.608-8 8 2.00 120 28 14 30 24 22 0.8010-8 10 3.15 152 36 18 38 29 28 1.7013-8 13 5.30 180 42 21 42 41 36 2.8016-8 16 8.00 221 54 27 52 45 43 5.10

18/20-8 18/20 12.50 270 62 30 65 58 55 8.7022-8 22 15.00 300 70 32 75 64 61 11.5026-8 26 21.20 335 78 39 78 70 68 17.2032-8 32 31.50 410 96 48 95 83 80 30.20

TWN 0858/1 Eye Slip Hook with Safety Latch



mm mm tonnes E G H C kg

6-8 6 1.12 75 23 17 16 0.308-8 8 2.00 99 30 22 22 0.6810-8 10 3.15 121 38 29 28 1.3713-8 13 5.30 143 44 37 36 2.5816-8 16 8.00 175 54 45 43 4.3618-8 18 10.00 195 60 52 50 7.5920-8 20 12.50 220 65 58 55 9.6822-8 22 15.00 244 75 64 61 10.62

TWN 0835/1 Sling Hook with Pin Coupling & Safety Latch




6-8 6 1.12 98 28 22 15 0.578-8 8 1.50 122 33 25 20 0.9310-8 10 3.15 150 45 35 27 1.7513-8 13 5.30 186 54 41 38 3.2516-8 16 8.00 215 67 54 39 5.60

18/20-8 18/20 12.50 238 78 54 48 8.00

TWN 0799 Self Locking Clevis Hook


27



mm mm tonnes E G L B kg

8-8 8 2.00 61 9 101 61 0.5310-8 10 3.15 73 12 125 75 0.9713-8 13 5.30 95 15 160 95 2.1816-8 16 8.00 112 18 188 120 3.4020-8 20 12.50 148 22.5 242 141 7.30

TWN 0827 Shortening or Grab Hook Cradle Type

with Pin Coupling



mm mm tonnes E G L B kg

8-8 8 2.00 61 9 101 61 0.5410-8 10 3.15 73 12 125 75 0.9913-8 13 5.30 94 15 160 95 2.1816-8 16 8.00 112 18 188 120 3.4520-8 20 12.50 148 22.5 242 141 7.35

TWN 0827/1 Shortening or Grab Hook Cradle Type

with Pin Coupling and Safety Device


TWN 0119 Transport Ring Weld-on Type

Trade Marking Working Dimensions in mm Weight

Size DSK-N Load Limit app.

mm tonnes E* F* C L H D B kg

6-8 1 1.12 59 31 32 32 28 12 36 0.248-8 2 2.00 69 37 38 38 33 14 42 0.4610-8 3 3.15 84 46 45 44 38 18 48 0.6313-8 5 5.30 120 69 60 60 51 24 66 1.6116-8 8 8.00 127 66 68 65 61 28 72 2.6722-8 15 15.00 178 98 96 109 80 39 120 8.0932-8 32 31.50 292 174 145 165 118 56 180 27.3040-8 50 50.00 370 227 205 180 143 72 230 60.00

* E and F dimensions vertical to welding level

06/0

7




8-8 8 2.00 110 66 33 27 1.0010-8 10 3.15 133 76 35 32 1.6113-8 13 5.30 159 89 41 38 3.4016-8 16 8.00 189 102 48 45 5.5018-8 18 10.00 218 114 54 51 9.0020-8 20 12.50 218 114 54 51 9.0022-8 22 15.00 244 124 60 56 12.00

TWN 0859 Foundry or Container Hook with Pin Coupling


B

28

06/0

7

Excel Grade 80 Components

CRO Eye Grab Hook

Code W.L.L. Chain ø Dimensions mm Weight

t mm A B C P kg

CRO 7/8 2.00 7/8 51 20 21 10 0.28CRO 10 3.15 10 54 29 29 12 0.55CRO 13 5.30 13 89 39 44 15 1.60CRO 16 8.00 16 104 42 45 19 2.43

CRO and CRC Grab Hooks are used to shorten or hold a length of chain. An extra deep, narrow throat engages chain between the links. There is no reduction of the W.L.L. Cradle grab hooks provide betterchain support than standard grab hooks. Its specific form makes accidental disengagement of the chain difficult. For intensive use however, we recommend using a shortening clutch (code GC of GCV). For safe use, a shortener must be assembled to the master link via 3-4 links of chain, and be independent of the loaded chain leg.

Safety Factor 4:1

CRC Clevis Grab Hook


t mm A P kg

CRO 7/8 2.00 7/8 63 9 0.30CRO 10 3.15 10 75 12 0.57CRO 13 5.30 13 102 15 1.54CRO 16 8.00 16 130 19 2.61

Safety Factor 4:1

GC and GCV Shortening Clutches are an essential part of chainslings, used to shorten the lengths of the chain legs, and prevent instability of the loads. Shortening clutches are also available with a locking system, designed to prevent accidental disengagement of the chain.

GC GCV Shortening Clutch

Code Code W.L.L. Chain ø Dimensions mm Weight

t mm A B kg

GC 6 GCV 6 1.12 6 54 22 0.22GC 7/8 GCV 8* 2.00 7/8 65 30 0.41GC 10 GCV 10 3.15 10 77 38 0.75GC 13 GCV 13 5.30 13 105 49 1.63GC 16 GCV 16 8.00 16 131 60 3.15GC 18/20 GCV20** 12.50 18/20 143 76 4.06

Safety Factor 4:1* Only for 8mm chain** Only for 20mm chain

29

06/0

7

Excel Grade 80 ComponentsCSE Swivel Sling Hook with large eye enables easy assembly onwire rope slings (with thimbles). There is also a flat on the eyesto fit omega links. All of these hooks, except the CSE 18/20, havea ball bearing in the swivel as a standard. This feature enablessmooth easy rotation under load.

CSE Swivel Sling Hook


t mm A D E P kg

CSE 5/6 1.12 5/6 101 29 33 28 0.40CSE 7/8 2.00 7/8 121 32 31 29 0.77CSE 10 3.15 10 147 37 40 31 1.41CSE 13 5.30 13 185 47 46 40 2.53CSE 16 8.00 16 211 57 58 47 3.90CSE 18/20 12.50 18/20 265 66 56 64 6.81

Safety Factor 4:1

XLE Swivel Self Locking Hook with large swivel eye makesassembly to wire rope slings (with thimbles) easier. There is alsoa flat on the eyes that enables assembly with omega links. All of these hooks have a ball bearing in the swivel as a standard.This feature enables smooth, easy rotation under load.

XLE Swivel Self Locking Hook


t mm A B C D E P kg

XLE 0 1.12 5/6 122 16 24 32 34 32 0.73XLE 1 2.00 7/8 148 23 29 37 40 44 1.35XLE 2 3.15 10 183 30 34 49 49 49 2.45XLE 3 5.30 13 214 35 43 56 61 64 4.38XLE 4 8.00 16 268 39 57 66 59 78 7.86XLE 5 12.50 18/20 350 53 59 82 90 92 12.50

Safety Factor 4:1

XLO Self Locking Hooks are traditional sized hooks with a largerrelease mechanism making them easier to use with gloves, andare therefore recommended for the construction industry. The large eye enables easy assembly on wire rope slings (withthimbles). The flat on the eyes makes assembly with omega links easier.

XLO Eye Self Locking Hook


t mm A B C D P kg

XLO 0 1.12 5/6 113 16 24 25 32 0.48XLO 1 2.00 7/8 132 23 29 29 44 0.90XLO 2 3.15 10 167 30 34 35 49 1.69XLO 3 5.30 13 194 35 43 47 64 3.28XLO 4 8.00 16 244 39 57 60 78 6.04XLO 5 12.50 18/20 284 53 59 69 92 9.40

Safety Factor 4:1

30

06/0

7

Excel Grade 80 ComponentsXLC Self Locking Hooks are traditional sized hooks with a largerrelease mechanism making them easier to use with gloves, andare therefore recommended for the construction industry. The clevis enables a direct connection to Grade 80 chains.

XLC Clevis Self Locking Hook


t mm A B C D P kg

XLC 0 1.12 5/6 92 16 24 28 32 0.47XLC 1 2.00 7/8 111 23 29 32 44 0.90XLC 2 3.15 10 141 30 34 41 49 1.72XLC 3 5.30 13 167 35 43 53 64 3.21XLC 4 8.00 16 205 39 57 64 78 5.93XLC 5 12.50 18/20 234 53 59 80 92 9.10

Safety Factor 4:1

GH Excavator Hook

Code W.L.L. Dimensions mm Weight

t A B P kg

GH 0.75 0.75 56 70 22 0.23GH 1 1.00 71 78 25 0.48GH 2 2.00 91 81 36 0.72GH 3 3.00 104 104 39 1.07GH 4 4.00 120 129 42 1.59GH 5 5.00 136 146 47 2.32GH 8 8.00 145 146 52 3.27GH 10 10.00 178 193 77 6.07GH 15 15.00 185 225 76 9.00

Safety Factor 4:1

GH Excavator Hooks are welded directly to the booms of bucketor crane loaders. (Welding instructions are supplied with eachhook). Note: Lifting with the teeth of an excavator is forbidden.Latches are fitted as standard, to prevent accidental unhooking.

Respect welding instructions.

MJ Chain Connectors provide fast, easy assembly without theneed for special tools or skills. Designed for attaching hooks,master links and other end fittings to Grade 80 alloy steel chains.

MJ Chain Connector


t mm A B C kg

MJ 6 1.12 6 45 40 15 0.14MJ 7/8 2.00 7/8 54 52 20 0.15MJ 10 3.15 10 63 65 25 0.32MJ 13 5.30 13 84 82 30 0.68MJ 16 8.00 16 104 103 36 1.26MJ 18/20 12.50 18/20 127 120 45 2.02MJ 22 15.00 22 155 144 51 3.18MJ26 21.20 26 160 172 57 4.52MJ 32 31.50 30/32 174 197 69 8.20

Safety Factor 4:1

31

06/0

7

Excel Stainless SteelComponents Grade 316

Omega Links are an easy and safe connection between the chainand the components.

COI Omega Link


t mm A B C kg

CO 6 I 0.70 6 25 20 9 0.07CO 7/8 I 1.20 7/8 34 23 16 0.16CO 10 I 1.60 10 41 31 17 0.28CO 13 I 2.70 13 54 40 21 0.63

Safety Factor 4:1

Chain Connectors provide fast, easy assembly without the needfor special tools or skills. Designed for attaching hooks, masterlinks and other end fittings to stainless steel chains.

MJI Chain Connector


t mm A B C kg

MJ 6 I 0.70 6 45 41 16 0.12MJ 7/8 I 1.20 7/8 55 52 20 0.16MJ 10 I 1.60 10 73 70 25 0.33MJ 13 I 2.70 13 92 85 29 0.70

Safety Factor 4:1

Excel Lifting Chain

Delivered in standard lengths or in cut lengths on request.

CI Lifting Chain

Code W.L.L. Dimensions mm Links Weight

t D A B m kg

C 6 I 0.70 6 18 7.8 53.4 0.78C 8 I 1.20 8 24 10.4 41.0 1.40C 10 I 1.60 10 30 13.0 32.7 2.20C 13 I 2.70 13 39 17.0 25.0 3.80

Safety Factor 4:1Standard length: 25m

Lifting Eye Bolts can be used only in their axis (angle must beless than 30°), never in oblique. W.L.L. is stamped on the bodies.The minimum factor of safety is 5:1.

ALI Eye Bolt

Code W.L.L. ø ISO Unmachined Dimensions mm Weight

t mm ø A B L C kg

AL 8 I 0.20 8 12 16 20 23 6 0.05AL 10 I 0.40 10 14 19 22 29 8 0.07AL 12 I 0.60 12 16 22 27 36 9 0.13AL 14 I 0.80 14 18 28 29 40 12 0.24AL 16 I 1.00 16 22 30 36 53 12 0.36AL 18 I 1.50 18 26 32 40 59 16 0.38AL 20 I 2.00 20 26 32 40 59 16 0.55AL 22 I 2.50 22 30 42 54 64 18 0.73AL 24 I 3.00 24 30 42 54 64 18 1.08

32

Safety Factor 5:1

06/0

7


Welded Master Links are designed for 1 or 2 leg slings (code MSI)and 3 or 4 leg slings (code MTSI). The master link assemblies (code MTSI) have a flat in order to make assembly with omega links (code COI) easier.

MSI Welded Master Link

Code Chain ø mm Dimensions mm W.L.L. Weight

1 leg 2 leg A B C t kg

MS 13 I 6 6 110 60 13 0.75 0.34MS 16 I 8 6 110 60 16 1.25 0.53MS 18 I 10 8 135 75 18 2.00 0.82MS 22 I 13 10 160 90 22 3.20 1.50MS 26 I 16 13 180 100 26 5.00 2.31

MTSI Master Link Assembly

Code Chain ø Dimensions mm W.L.L. Weight

3/4 legs A B C a b Dia t kg

MTS 18 I 6 135 75 18 54 25 13 1.60 1.16MTS 22 I 8 160 90 22 70 34 16 2.65 2.22MTS 26 I 10 180 100 26 85 40 18 4.25 3.37MTS 32 I 13 200 110 32 115 50 22 6.70 6.07

Sling Hooks have incomparable qualities due to their uniquedesign. The forged latch is fitted with a stainless steel spring and a pin.Eye Sling Hooks with large eye enable easy assembly on wirerope slings (with thimbles). The flat on the eye makes assemblywith an omega link (code COI) easier.


t mm A B P C kg

CSO 5/6 I 0.70 5/6 86 24 28 16 0.25CSO 7/8 I 1.20 7/8 102 26 29 19 0.53CSO 10 I 1.60 10 121 35 31 22 0.90CSO 13 I 2.70 13 154 41 40 31 1.75

Safety Factor 4:1

CSOI Eye Sling Hook

Clevis Sling Hooks enable a direct connection to the stainlesssteel chain (code CI).

Safety Factor 4:1

CSCI Clevis Sling Hook


t mm A B P kg

CSC 5/6 I 0.70 5/6 73 16 28 0.26CSC 7/8 I 1.20 7/8 95 20 29 0.49CSC 10 I 1.60 10 110 24 31 0.94CSC 13 I 2.70 13 138 31 40 1.80

33

Safety Factor 4:1

Safety Factor 4:1


Screw Type Dee Shackles are forged and guarantee high qualityand performance.

MDVI Screw Type Dee Shackle


t A F B C kg

MDV 0.4 I 0.40 32 8 8 16 0.07MDV 0.6 I 0.60 38 9.5 10 20 0.11MDV 0.9 I 0.90 50 12 12 25 0.25MDV 1.5 I 1.50 52 13 16 24 0.40MDV 2.5 I 2.50 65 16 20 28 0.60MDV 3 I 3.00 72 19 22 30 0.90MDV 4 I 4.00 78 19 25 32 1.10MDV 6 I 6.00 94 25 30 40 2.40

Safety Factor 6:1Larger sizes upon request.

Screw Type Anchor Shackles feature an open throat design thatpermits free line movement without undue wear. The wide bowallows ample clearance for thimbles and turnbuckles. Theseforged shackles guarantee high quality and performance.

MLVI Screw Type Anchor Shackle


t A F B C D kg

MLV 0.4 I 0.40 30 8 8 16 23 0.07MLV 0.6 I 0.60 36 9.5 10 20 27 0.11MLV 0.9 I 0.90 47 12 12 25 37 0.25MLV 1.5 I 1.50 47 13 16 25 33 0.37MLV 2.5 I 2.50 60 16 20 28 42 0.65MLV 3 I 3.00 67 19 22 30 51 1.00MLV 4 I 4.00 84 22 25 36 57 1.70MLV 6 I 6.00 95 25 30 40 66 2.50

Safety Factor 6:1Larger sizes upon request.

06/0

7

34

06/0

7

Working Inside Inside Length Width Approx. Weight Each

Load Limit Dia. bow Dia. Pin Width Chain Type Anchor of Bow Screw SafetyMetric d D W L Type L B Pin PinTonnes m mm mm mm mm mm kg kg

0.33 5 6 10 - 22 15 0.02 -

0.50 6 8 12 22 29 20 0.06 0.07

0.75 8 10 13 26 31 21 0.11 0.13

1.00 10 11 17 32 37 26 0.15 0.17

1.50 11 13 18 37 43 29 0.21 0.25

2.00 13 16 21 41 48 33 0.37 0.44

3.25 16 19 27 51 61 43 0.65 0.79

4.75 19 22 32 60 72 51 1.06 1.26

6.50 22 25 37 71 84 58 1.56 1.88

8.50 25 29 43 81 95 68 2.32 2.78

9.50 29 32 46 90 108 74 3.28 3.87

12.00 32 35 52 100 119 83 4.51 5.26

13.00 35 38 57 113 133 92 5.43 6.94

17.00 38 41 60 124 146 98 7.89 8.79

25.00 44 51 73 146 178 127 13.40 14.99

35.00 51 57 83 171 197 146 18.85 20.65

45.00 57 63 95 181 222 160 26.06 29.01

55.00 63 70 105 203 267 184 37.86 41.05

85.00 76 83 127 229 330 200 58.68 62.24

120.00 89 95 146 267 381 241 - 110.0

150.00 102 108 165 318 432 279 - 160.0

Orange Painted Pin to A.S.2741 SAFETY FACTOR OF 6

Alloy Grade ‘S’ Shackles Load Chart

Also available in Grade ‘M’ and Commercial type.

Please contact our Sales Department for further information.

CHAIN SHACKLEWITH

SCREW PIN

ANCHOR SHACKLEWITH

SCREW PIN

SAFETY ANCHORSHACKLE

BOLT TYPE

SAFETY CHAINSHACKLE

BOLT TYPE

35

06/0

7

PWB AnchorHerc-Alloy 800™ ChainCombining the qualities of high strength, low weight and durability resultingin easy, safe handling, Herc-alloy 800 chain is manufactured to the most exacting quality control standards and conforms to the mechanical properties of Grade T Chain specified in Australian Standard AS2321.Available in sizes ranging from 6mm to 32.0mm.

Chain Size WLL S R Fmm tonnes mm mm mm

6.0 1.2 6.3 20.8 22.3

7.1 1.6 7.1 23.8 25.9

8.0 2.0 8.0 23.5 27.0

10.0 3.2 9.7 29.8 33.8

13.0 5.4 12.7 38.0 43.0

16.0 8.0 16.0 47.3 54.0

20.0 12.5 20.0 59.2 67.5

22.0 15.5 22.0 65.0 74.2

26.0 21.6 26.0 78.0 90.0

32.0 32.8 32.0 96.0 111.0

Herc-Alloy 800™ Chain may be supplied with the following identification markings: HA800 CM, PWB HA800, PWB HA, HACM, CMU HA 800, G80, G800, HA800, HA8, PWB-HA8.

Chain sizes 6mm to 22mm manufactured in Australia.

36

06/0

7

Temperature Reduction Range of WLL

°C while heated

Up to 200 Nil

200 - 300 10%

300 - 400 25%

Over 400 Do not use

PWB AnchorCare, Use and Inspection of Herc-Alloy 800™ Chain SlingsCare

Store Herc-Alloy 800 chain slings on A-frames or wall racks in a clean dry place.

Lightly oil Herc-Alloy 800 chain slings before prolonged storage.

Never heat-treat Herc-Alloy 800 chain slings.

Use

Always inspect a chain sling before use to ensure it is free from damage or wear.

Ensure that the load is evenly distributed on all sling legs.

Ensure that the chain is free of twists and is protected from any sharp corners on the load.

Commence the lift slowly, taking up the slack gradually.

When lowering, avoid the possibility of crushing the chain by ensuring that the load does

not land on it.

Inspection

It is important to inspect chain slings regularly and that a record is kept for each chain sling.

If necessary, clean the sling before inspection.

Every chain link should be individually inspected for signs of wear, twisting, stretching, nicks or

gouging and any worn link measured to determine degree of wear.

Oblong links and hooks should be inspected at their loadbearing points for signs of wear or

distortion, eg widening of hook throat opening.

Defective chain links or fittings should be clearly marked to indicate rejection, and the chain

sling withdrawn from service until repaired.

Hammerloks should be inspected for any signs of wear at their loadbearing points, for

excessive play of the load pin within the body halves and for impaired rotation of the body

halves around the load pin. (Note: when reassembling a Hammerlok it is recommended that

a new pin and stud assembly be used).

Effects of Hazardous Conditions

Heat Conditions

The strength of all chain slings is adversely affected by heat so

care must be exercised when using at elevated temperatures.

Where temperatures are likely to be higher than 200°C

reductions in the working load limits of Herc-Alloy 800

slings should be applied. (See table).

Heat Treatment

Herc-Alloy 800 Chain and Fittings do not require periodic

heat treatment and must never be heat treated.

Corrosive Conditions

Herc-Alloy 800 Chain and Fittings should not be used in acid or other corrosive environments.

Galvanising

Herc-Alloy 800 Chain and Fittings must never be hot dipped, mechanically galvanised or

electroplated except by PWB Anchor.

Hot dipped galvanised slings must always have their working load reduced by 20%.

37

06/0

7

M

D

BG

F

E

C

Type WLL B C D F G M Weight Ref. No.(kgs) (mm) (kgs/pc.)

PP-B-0.63t-M12 630 65 35 40 18 41 12 0.35 798 9522PP-B-1.5t-M16 1500 65 35 46 24 50 16 0.6 798 9523PP-B-2.5t-M20 2500 75 40 61 30 61 20 1.1 798 9081PP-B-4t-M24 4000 95 45 78 36 78 24 2.4 798 9082PP-B-5t-M30 5000 130 60 95 45 93 30 5.2 798 9524PP-B-8t-M36 8000 140 65 100 54 102 36 6.3 798 9083

M

BE

D

GF

C

Type WLL F1 WLL F2 D K L Weight Ref. No.(kgs) (kgs) (mm) (kgs/pc.)

VRS-F-M8 1000 400 25 47 15 0.10 850 0911VRS-F-M10 1000 400 25 47 15 0.12 710 4029VRS-F-M12 2000 750 30 56 18 0.18 710 1313VRS-F-M16 4000 1500 35 65 24 0.32 710 1314VRS-F-M20 6000 2300 40 75 30 0.51 710 1315VRS-F-M24 8000 3200 48 90 36 0.92 710 1316VRS-F-M30 12000 4500 60 112 45 1.80 710 1317VRS-F-M36 16000 7000 72 135 54 3.35 798 4201VRS-F-M42 24000 9000 82 158 63 5.14 798 4202VRS-F-M48 32000 12000 94 180 72 7.80 798 4203

® ®

VLBGRing boltwith Metric coarse thread360° rotation

RBG/VRBGEye plate Bolt on

PP-BBolt-on eye connection(swivelling) metric thread

PP-SBolt-on universal connection(swivelling) metric thread

Type WLL F1 WLL F2 D K L Weight Ref. No.(kgs) (kgs) (mm) (kgs/pc.)

VRM-M8 1000 400 25 47 12 0.10 799 2989VRM-M10 1000 400 25 47 15 0.10 799 0311VRM-M12 2000 750 30 56 18 0.20 799 0312VRM-M16 4000 1500 35 65 24 0.30 799 0314VRM-M20 6000 2300 40 75 30 0.50 799 0315VRM-M24 8000 3200 48 90 36 0.90 799 0316VRM-M30 12000 4500 60 112 45 0.70 799 3008

Type WLL B C D F G M Weight Ref. No.(kgs) (mm) (kgs/pc.)

PP-S-0.63t-M12 630 75 18 40 18 41 12 0.4 799 0719PP-S-1.5t-M16 1500 97 25 46 5 50 16 1.0 798 9719PP-S-2.5t-M20 2500 126 30 61 30 61 20 1.7 798 9075PP-S-4t-M24 4000 150 35 78 36 77 24 3.5 798 9076PP-S-5t-M30 5000 174 40 95 45 93 30 7.2 798 9720PP-S-8t-M36 8000 208 48 100 54 102 36 9.2 798 9077

D

LC

T

H

Type WLL D L Bolt Weight Ref. No.(kgs) (mm) Size (kgs/pc.)

RBG-3 3200 48 178 M16 x 50 0.90 51817RBG-8 8000 65 194 M20 x 70 3.80 59971VRBG-16 16000 90 270 M30 x 90 7.8 799 3255VRBG-30 30000 130 400 M30 x 100 67 798 5866VRBG-50 50000 230 650 M36 x 120 210 798 5867

Type WLL C H T Weight Ref. No.(kgs) (mm) (kgs/pc.)

VLBG-0.3t-M8 300 34 11 75 0.40 850 0821VLBG-0.63t-M10 630 34 16 75 0.40 850 0822VLBG-1t-M12 1000 34 21 75 0.40 850 0823VLBG-1.5t-M16 1500 36 24 85 0.50 850 0824VLBG-2.5t-M20 2500 54 32 110 1.30 850 0826VLBG-4t-M24 4000 54 37 125 1.50 850 0827VLBG-4t-M27 4000 65 39 147 3.10 798 3658VLBG-5t-M30 5000 65 49 147 3.30 850 0828VLBG-7t-M36 7000 65 52 146 3.40 850 0829VLBG-8t-M36 8000 82 63 197 5.80 798 3553VLBG-10t-M42 10000 80 73 162 6.40 798 3554VLBG-15t-M42 15000 100 63 222 10.7 798 2966VLBG-20t-M48 20000 100 73 222 11.1 798 2967

K

L

K

L

D

C

D

D

Type WLL F1 WLL F2 C D Weight Ref. No.(kgs) (kgs) (mm) (kgs/pc.)

RS-M6 400 100 12 25 0.10 61401RS-M8 800 200 12 25 0.10 61402RS-M10 1000 250 15 25 0.12 56397RS-M12 1600 400 18 30 0.18 56398RS-M14 3000 750 21 35 0.30 56403RS-M16 4000 1000 24 35 0.30 56404RS-M20 6000 1500 30 40 0.47 56407RS-M24 8000 2000 36 50 0.89 56408RS-M30 12000 3000 45 60 1.57 56409RS-M36 16000 4000 54 90 6.20 56954RS-M42 24000 6000 63 90 6.40 56955RS-M48 32000 8000 68 90 6.60 56956

VRS-F Starpoint Eyebolt with Metric coarse thread360° Rotation

VRM Starpoint Eyenut with Metric coarse thread360° Rotation

RS EyeboltMetric coarse threadHigh tensile

38

06/0

7

WPP-B Weld-on eye connection (swivelling)

VRBS Eye plate. Ready for welding

VRBKEye plate for cornersReady for welding

VLBS (W/S)Load ring without springReady for welding

LBS (S/S)Stainless steel load ringReady for welding

Type WLL B C F Weight Ref. No.(kgs) (mm) (kgs/pc.)

VRBS-4 4000 135 48 16 0.80 799 2488VRBS-6.7 6700 170 60 20 1.80 799 2489VRBS-10 10000 195 65 22 2.80 799 2490VRBS-16 16000 266 90 30 6.60 799 2491VRBS-30 30000 375 130 42 19.0 60267VRBS-50 50000 620 230 70 85.0 56834

Type WLL A B C D E G Weight Ref. No.(kgs) (mm) (kgs/pc.)

WPP-B-0.63t 630 9 65 35 40 105 40 0.35 798 9954WPP-B-1.5t 1500 11 65 35 46 115 50 0.6 798 9955WPP-B-2.5t 2500 13 74 40 61 135 61 1.0 798 9956WPP-B-4t 4000 16 95 45 80 172 77 2.3 798 9957WPP-B-5t 5000 21 130 60 95 223 93 4.7 798 9958WPP-B-8t 8000 24 140 65 100 242 102 5.3 798 9959


WPPH-S-0.63t 630 13 75 18 34 109 34 0.35 799 0722WPPH-S-1.5t 1500 20 97 25 141 44 44 0.95 798 9966WPPH-S-2.5t 2500 28 126 30 53 179 53 1.4 798 9967WPPH-S-4t 4000 36 150 35 68 217 67 3.2 798 9968WPPH-S-5t 5000 37 174 40 83 253 79 6.9 798 9969WPPH-S-8t 8000 49 208 48 88 296 88 8.0 798 9970


VRBK-4 4000 135 48 16 0.90 799 2879VRBK-6.7 6700 174 60 20 1.30 799 2880VRBK-10 10000 208 65 22 4.30 799 2881

ØD

AB

G

E

C

WPPH-S Weld-on universal connection(non-swivelling)

ØD

AB

GE

C

t

ØD

A

BG

E

C

WPP-S Weld-on universal connection (swivelling)


WPP-S-0.63t 630 13 75 18 40 115 40 0.4 799 0721WPP-S-1.5t 1500 20 97 25 46 147 50 1.0 798 9944WPP-S-2.5t 2500 28 126 30 61 187 61 1.5 798 9945WPP-S-4t 4000 36 150 35 80 227 77 3.3 798 9946WPP-S-5t 5000 37 174 40 95 267 93 7.1 798 9947WPP-S-8t 8000 49 208 48 100 310 102 8.2 798 9948

VABH-W Weld-on excavator hook

WPPH-B Weld-on eye connection (non-swivelling)


WPPH-B-0.63t 630 9 65 35 34 99 34 0.3 798 9976WPPH-B-1.5t 1500 11 65 35 40 109 44 0.5 798 9977WPPH-B-2.5t 2500 13 74 40 53 127 53 0.9 798 9978WPPH-B-4t 4000 16 95 45 68 163 67 2.2 798 9979WPPH-B-5t 5000 21 130 60 83 209 79 4.5 798 9980WPPH-B-8t 8000 24 140 65 88 228 88 5.1 798 9981

ØD

A

BG

E

C

B

C

F

E

CF

Type WLL C E F Weight Ref. No.(kgs) (mm) (kgs/pc.)

LBS(S/S)-1 500 36 39 13.5 0.30 51630LBS(S/S)-3 1000 50 50 16.5 0.60 51740LBS(S/S)-5 2000 65 72 22.5 1.60 53377

B

C

F

E

C

F

B G

DVCGH-S High capacity weld-onexcavator hook

Type WLL B D G Weight Ref. No.(kgs) up to 45° (mm) (kgs/pc.)

VCGH-S 16 10000 141 220 100 5.0 798 4047VCGH-S 20 16000 187 288 120 8.4 798 4310VCGH-S 22 20000 195 292 120 14.5 798 4312

Type WLL C E F Weight Ref. No.(kgs) (mm) (kgs/pc.)

VLBS(W/S)-1.5 1500 38 40 13.5 0.35 799 3115VLBS(W/S)-4 4000 51 52 16.5 0.80 799 3116VLBS(W/S)-6.7 6700 67 73 22.5 1.90 799 3117VLBS(W/S)-10 10000 67 71 26.5 2.90 799 3118VLBS(W/S)-16 16000 100 105 26.0 6.80 799 3041

B

C

F


VABH-W 1.5t 1500 78 117 70 0.8 850 2195VABH-W 2.5t 2500 101 148 85 1.8 850 2144VABH-W 4t 4000 122 171 104 3.1 850 2222VABH-W 6.7t 6700 156 208 120 5.9 850 2239

39

06/0

7

VIP - Special QualityFor single and multiple strand sling chains with different angles of inclination forsymmetrical loading of the strands.

Available in sizes 4mm through to 22mm. Every chain link is stamped with the VIPlogo. Serial and batch numbers are stamped every running metre. A highly visiblecolour which discolours under high temperatures and a dual process surface coat-ing for increased corrosion resistance.

WBG-VSwivel ring boltMetric coarse pitch 360° rotationStandard (F*) and variable (Fvario) boltlengths available

WBGSwivel ring boltHeavy duty Metric coarse pitch 360° rotation

Type WLL A C F Weight Ref. No.(kgs) (mm) (kgs/pc.)

WBG-8 M36 8000 22 50 54 4.75 51872WBG-10 M42 10000 26 65 63 6.4 51874WBG-10 M48 10000 26 65 68 6.6 51930WBG-15 M56 15000 32 70 84 11.2 51941WBG-15 M64 15000 32 70 96 11.5 710 0406WBG-35 M90 35000 40 80 135 13.6 798 5363

Grade 100 Alloy Chain - RUDThe most technologically advanced alloy sling chain system available - with25% higher working load capacity and greater wear resistance than Grade 80(T) chain. This system comes with an extensive range of fittings, to offer themost innovative chain sling system available.

VIP Overheating IndicationThis special fluorescent pink powder coating permanently changes colour atincreased temperatures. Colour black signifies an application at more than400°C (715°F). Further use is then prohibited.

F V

AR

IO

AC

A

F

C

WLL in tonnessingle leg slings

Straightsling

Straight sling

60˚ 90˚ 120˚ 60˚ 90˚ 120˚ 60˚ 90˚ 120˚Reeved

slingReeved

slingReeved sling Basket sling

slings of 2, 3 or 4 legs endless slings

Temperature ˚C -10 < to + 200 over 200 to 300 over 300 to 400

Deration none 10% 25%

RUD – LiftingSystems in

Special Quality

Chain dia.

S

Grade 100

VIP 4 0.63 0.47 1.1 0.89 0.63 0.82 0.66 0.47 0.82 0.66 0.47 0.94VIP 6 1.5 1.1 2.6 2.1 1.5 1.95 1.6 1.1 1.95 1.6 1.1 2.2VIP 8 2.5 1.9 4.3 3.5 2.5 3.2 2.6 1.9 3.2 2.6 1.9 3.7VIP 10 4.0 3.0 6.9 5.6 4.0 5.2 4.2 3.0 5.2 4.2 3.0 6.0VIP 13 6.7 5.0 11.6 9.4 6.7 8.7 7.1 5.0 8.7 7.1 5.0 10.0VIP 16 10.0 7.5 17.3 14.1 10.0 13.0 10.6 7.5 13.0 10.6 7.5 15.0VIP 20 16.0 12.0 27.8 22.7 16.0 20.8 17.0 12.0 20.8 17.0 12.0 24.1VIP 22 20.0 15.0 34.6 28.2 20.0 26.0 21.2 15.0 26.0 21.2 15.0 30.0

Type WLL B C F G H Weight Ref. No.(kgs) (mm) (kgs/pc.)

VABH-B-1.5t 1500 78 117 70 48 60 0.78 850 2194VABH-B-2.5t 2500 101 148 85 60 75 1.73 850 2143VABH-B-4t 4000 122 171 104 70 90 3.0 850 2221VABH-B-6.7t 6700 156 208 120 85 110 5.6 850 2238

VABH-BExcavator Hook bolt-onExtremely robust forged safety latchNon-protruding tip of the hook

Type WLL A C F* Weight Ref. No.(kgs) (mm) (kgs/pc.)

WBG-V-0.3 M8 300 8 29 12 0.17 710 3720WBG-V-0.45 M10 450 8 29 15 0.19 710 3715WBG-V-0.6 M12 600 10 35 21 0.38 710 0180WBG-V-1.3 M16 1300 10 35 30 0.56 710 0430WBG-V-2.0 M20 2000 13 35 33 1.28 710 0800WBG-V-3.5 M24 3500 18 40 40 2.66 710 0640WBG-V-5.0 M30 5000 22 50 50 5.00 710 0650

Due to a special heat treatment developed by RUD, the high-dynamic VIP chainsare more resistant to external mechanical wear friction and damage. Therefore,longer service life is guaranteed.

All RUD-VIP chains and components are electromagnetically crack detected toensure greater safety.

C

FGB

H

40

06/0

7

VAK1VIP-Master link for single leg slings(regular size)Compact - Extra Large also available

Type WLL Chain B C T Weight Ref. No.(kgs) (mm) (mm) (kg/pc.)

VAK 1-6 1500 6 60 110 138 0.6 710 0681VAK 1-8 2500 8 60 110 147 0.9 710 0682VAK 1-10 4000 10 75 135 181 1.4 710 0683VAK 1-13 6700 13 90 160 218 2.4 710 0684VAK 1-16 10000 16 100 180 250 3.7 710 0685VAK 1-20 16000 20 180 340 434 14.7 710 4089VAK 1-22 20000 22 180 340 434 16.5 710 0686

B C TVAK 4VIP-Master link for four leg slings(regular size)Compact - Extra Large also available

Type Chain B C T Weight Ref. No.(mm) (mm) (kg/pc.)

VAK 4-6 6 75 135 217 1.5 710 0742VAK 4-8 8 90 160 268 2.8 710 0743VAK 4-10 10 100 180 311 4.6 710 0744VAK 4-13 13 110 200 373 8.3 710 0745VAK 4-16 16 140 260 470 13.7 710 0746VAK 4-20 20 190 350 614 39.0 710 4181VAK 4-22 22 190 350 614 40.1 710 0747

B C T

VAK 2VIP-Master link for two leg slings(regular size)Compact - Extra Large also available

B C T

VKSPSChain Tensioner with full,even adjustmentson both ends

Type L-open L-closed Adjust. Pretension Weight Ref. No.(mm) (mm) (mm) STF (daN) (kg/pc.)

VKSPS-6 323 204 120 1500 0.9 799 0170VKSPS-8 518 308 210 2500 2.8 798 7907VKSPS-10 533 324 210 2800 3.1 798 7994VKSPS-13 787 487 300 3600 8.0 799 0133VKSPS-16 807 507 300 3600 8.8 799 0135

VKSPS-RRatchet Chain Tensionerwith fold down handle

Type L-open L-closed Adjust. Pretension Weight Ref. No.(mm) (mm) (mm) STF (daN) (kg/pc.)

VKSPS-R-6 323 204 120 1500 0.95 799 0169VKSPS-R-8 518 308 210 2500 3.2 798 8569VKSPS-R-10 533 324 210 2800 3.6 798 8570VKSPS-R-13 787 487 300 3600 8.0 799 0132VKSPS-R-16 807 507 300 3600 9.3 799 0134

L L

Type Chain B C T Weight Ref. No.(mm) (mm) (kg/pc.)

VAK 2-6 6 60 110 138 0.7 710 0706VAK 2-8 8 75 135 172 1.4 710 0707VAK 2-10 10 90 160 206 2.3 710 0708VAK 2-13 13 100 180 238 3.9 710 0709VAK 2-16 16 110 200 270 6.6 710 0710VAK 2-20 20 180 340 434 16 710 4095VAK 2-22 22 180 340 434 20 710 0711

41

06/0

7

VVHVIP Clevis Grab Hook

VBMHWAVIP swivelling Bale Hook

VMVK/VVVIP Shortening Claws

VCGHVIP-Cobra Hook with safety latch

VAGHClevis self locking design in VIP quality

Type WLL F G T Weight Ref. No.(kgs) (mm) (kgs/pc.)

VCGH-6 1500 25 72 76 0.4 710 0498VCGH-8 2500 30 95 97 0.9 710 0499VCGH-10 4000 35 118 108 1.5 710 0500VCGH-13 6700 40 135 126 2.7 710 0501VCGH-16 10000 48 161 152 4.3 710 0502VCGH-20 16000 63 218 195 10.0 710 3385VCGH-22 20000 63 223 198 11.5 710 1603

Type WLL Chain E F T Weight Ref. No.(kgs) (mm) (mm) (kg/pc.)

VAGH-8 2500 8 91 43 117 0.9 710 1500VAGH-10 4000 10 109 47 140 1.9 710 1501VAGH-13 6700 13 138 64 169 3.4 710 1502

Type WLL Chain B2 T G Weight Ref. No.(kgs) (mm) (mm) (kg/pc.)

VMVK-6 1500 6 45 66 44 0.65 798 4072VMVK-8 2500 8 56 88 55 1.0 710 0760VMVK-10 4000 10 75 110 72 1.5 710 0761VMVK-13 6700 13 92 143 96 3.6 710 0762VMVK-16 10000 16 128 176 116 6.2 710 0763VMVK-20 16000 20 137 209 123 11.5 710 4296VV-22 20000 22 N/A 140 90 8.3 7102464

Type WLL Chain D F T Weight Ref. No.(kgs) (mm) (mm) (kg/pc.)

VVH 6 1500 6 43 23 50 0.25 798 8658VVH 8 2500 8 54 33 64 0.35 798 7319VVH 10 4000 10 68 42 80 0.80 798 7320VVH 13 6700 13 87 47 103 2.2 798 7321VVH 16 10000 16 108 57 125 2.7 798 8669

Type WLL A B C D E F Weight Ref. No.(kgs) (mm) (kgs/pc.)

VCH-SL 10000 18 71 42 40 50 47 2.4 850 3115

* Alternative container hook designs available in 10t and 20t WLL

G

TF

B2

T

T

F

E

F

T

D

B

T

CA

Type WLL A B C T Weight Ref. No.(kgs) (mm) (kgs/pc.)

VBMHWA-8 2500 35 18 61 381 2.5 799 1478VBMHWA-10 4000 35 18 61 381 2.5 798 9017

VWHVIP Foundry HookWide mouth opening with extra strong forged hook

VVSVIP Chain Coupling

Type WLL Chain B D T Weight Ref. No.(kgs) (mm) (mm) (kg/pc.)

VVS 6 1500 6 50 14 40 0.1 798 8419VVS 8 2500 8 64 19 53 0.2 798 5714VVS 10 4000 10 80 23 70 0.4 798 5715VVS 13 6700 13 96 27 81 0.7 798 4293VVS 16 10000 16 125 34 104 1.5 798 6984VVS 20 16000 20 155 41 124 3.0 798 4055VVS 22 20000 22 170 46 133 3.9 798 4056

B

D

T

VCHVIP Container HookStrong and compact with amaximum inclination angle of 45°

T

F

A

B

D

G

Type WLL Chain A B D F T Weight Ref. No.(kgs) (mm) (mm) (kgs/pc.)

VWH-6 1500 6 30 22 30 50 87 0.5 710 0210VWH-8 2500 8 40 29 40 64 115 0.9 710 0211VWH-10 4000 10 46 37 50 76 130 1.7 710 0212VWH-13 6700 13 51 45 64 90 168 3.0 710 0213VWH-16 10000 16 64 56 75 100 190 5.7 710 0214

42

06/0

7

Lifting Mode Vertical Choke Basket 30° 60° 90° 120° 60° 60°Choke

Capacity S.W.L. S.W.L. S.W.L. S.W.L. S.W.L. S.W.L. S.W.L S.W.L. S.W.L.

Kg Kg Kg Kg Kg Kg Kg Kg Kg Kg

1000 Violet 1000 800 2000 1900 1700 1400 1000 1700 1400

2000 Green 2000 1600 4000 3800 3400 2800 2000 3400 2800

3000 Yellow 3000 2400 6000 5700 5100 4200 3000 5100 4200

4000 Grey 4000 3200 8000 7600 6800 5600 4000 6800 5600

5000 Red 5000 4000 10000 9500 8500 7000 5000 8500 7000

6000 Brown 6000 4800 12000 11400 10200 8400 6000 10200 8400

8000 Blue 8000 6400 16000 15200 13600 11200 8000 13600 11200

10000 Orange 10000 8000 20000 19000 17000 14000 10000 17000 14000

FEATURES

• All slings are made from 100% Polyester.• WLL is clearly marked on each sling.• Colour coding on each sling for added

safety.• Protective sleeves are recommended for

lifting sharp and rough objects.

Round Slings

Webbing

Slings &

Round Slings

ColourCode

FLAT SLINGSManufactured to A.S.1353 Parts 1 & 2 SAFETY FACTOR 8:1

ROUND SLINGSManufactured to A.S. 4497.1SAFETY FACTOR 7:1

Flat Webbing and Round Slings Load Chart

Flat Webbing Slings

43

Deck or Eye PlatesHW 13 Rectangular Base

Admiralty Pattern

Material : BS970 - 150M19Normalised

Also available in other materials and Stainless Steel to order.

44

06/0

7

Long Shank EyeboltsProduced from BS 529 part 1

1944 Forgings

Material:As specified in BS 529 Hardened and tempered S.W.L. shown at 0° (Vertical) angle of lift.

Sizes under 12mm except 3/8” ARE NOT RECOMMENDED FOR LIFTING

Produced from 12mm Long Shank BS 4278 Table 1: 1984 Forgings

Part Dia. of Dia. Base Plates Total Proof Weight WLLNo. material of Height Load each @

in eye eye 5:1

A B C D E Fmm mm mm mm mm mm Tonnes kgs Tonnes

HWa13/1 10 20 25 45 6 38 2.0 0.14 1.5

HWa13/2 12.5 25 35 60 8 50 3.5 0.31 2.4

HWa13/3 16 32 45 70 10 64 5.5 0.45 3.5

HWa13/4 19 38 50 85 12 76 7.5 0.79 6.0

HWa13/5 22 44 60 100 12.5 89 9.7 1.36 6.5

HWa13/6 25 50 70 115 16 100 13.0 1.82 9.0

HWa13/7 28 57 75 130 17 114 16.0 2.95 10.0

HWa13/8 32 64 85 145 19 128 20.0 3.86 15.0

HWa13/9 35 69 95 158 21 140 24.0 5.11 20.0

HWa13/10 38 76 100 170 22 152 29.0 6.58

HWa13/12 50 100 140 230 30 203 50.0 14.98

Part SWL Thread B E F G H WeightNo. Size Each

Tonnes mm mm mm mm mm kg

EBLS10 0.25 M10 22 15 9 20 178 0.2

EBLS12 0.40 M12 28 19 11 25 178 0.2

EBLS14 0.50 M14 36 24 14 32 178 0.5

EBLS16 0.80 M16 36 24 14 32 178 0.5

EBLS18 1.00 M18 43 29 17 38 178 0.8

EBLS20 1.60 M20 43 29 17 38 178 0.8

EBLS22 1.60 M22 50 33 20 44 178 1.0

EBLS24 2.50 M24 57 38 22 51 178 1.5

EBLS27 2.50 M27 71 48 28 63 178 2.0

EBLS30 4.00 M30 71 48 28 63 178 2.9

Thiele Grade 80 Alloy Chain - Schillings

Documents

Transcript of Thiele Grade 80 Alloy Chain - Schillings