Technical Manual INTERTON Elipse Digital...

Global Technical Operations gto.gnresound.com

Lautrupbjerg 7 • DK-2750 Ballerup • DenmarkE-Mail: [email protected]

Technical ManualINTERTON

Elipse Digital SPBTE

Doc 0194590 rev. C

of 11

Not subject to issue control when printed

Subject Page

Description ..................................................................................................... 3 Part List ......................................................................................................... 4 Part List - HSG Parts...................................................................................... 5 CROS/BICROS System ................................................................................. 6 HI Dissembly .................................................................................................. 7 Amplifier ......................................................................................................... 8 Replacement of Microphone & Receiver........................................................ 9 Replacement of VC & TC ............................................................................. 10 Test................................................................................................................11

Table of Contents

Doc 0194590 rev. C

of 11


Description

Model Data Sheet

ELIPSE EL90-VI 17141700

Beige Brown Grey

Available in Beige, Brown & Grey

Doc 0194590 rev. C

of 11


Item Part No

MIC. SUSPENSION 15297000

MICROPHONE 33M 15240900

MICROPHONE,COMPL 15988900WIRE,ESW,AMBER,7X32U,14MM 15129714

WIRE,ESW,GREEN,7X32U,14MM 15129814

WIRE,ESW,RED,7X32U,14MM 15129614

PLASTIC BOLT 15284000

REC COMPL. 15989200

AMPL COMPL 17188401

TELECOIL 16453100

VC NUT 15341000

VC COVER SILICONE 15282900VC PLATE 15283000VC 50K LINEAR PJ77 15751101

Item Part No

HI-PRO PROG. CABLE CS44, R 9022 907 69019

HI-PRO PROG. CABLE CS44, L 9022 907 69029

TEST RING 15472600

TEST FIXTURE 16611100

TEST FRAME 16902800*

CONFORMAL COATING SL1367 **

ADULT HOOK W/O FILTER 15353200

ADULT HOOK WITH FILTER 15418400

BABY HOOK WITH FILTER 15427800

BABY HOOK W/O FILTER 15350900

FILTER-GR BF 1999 70930834

* Test frame p/n 1-21-65900 can be used as well

**Conformal coating SL1367 peters coat to be purchased locally. Check **e.g. the vendor website http://www.peters.de

Part List

Doc 0194590 rev. C

of 11


HSG Parts For HIBEIGE

For HIBROWN

For HIGREY

HSG PARTS TRANSP(optional)

AU COVER,PTD 16429100 16429101 16429105 16429103

AU COVER,PTD - BLUE** 16429104 16429104 16429104 -

AU COVER,PTD - RED** 16429106 16429106 16429106 -

BAT DR,PTD,CE-MARK,EL90 17366500 17366501 17366505 -

HSG,BACK (VC SIDE) 15339400 15339401 15339405 -

HSG,FR,PTD, EL90-VI 16729400 16729401 16729405 -

PC COVER,MOULDED 15339500 15339501 15339505 15339503

PC COVER,PTD,L** 16003100 16003101 16003105 16003103

PC COVER,PTD,R** 16003000 16003001 16003005 16003003

PB COVER 15893300 15893301 15893305 15893303

VC COVER PROTECTION (optional) 15427400 15427401 15427402 15427403

** To be mounted for indication of Right/Left side

VC cover optional(child protection cover)

Part List - HSG Parts

Doc 0194590 rev. C

of 11


Description Part No

AUDIO-BOOT (for HI) 16987200

AUDIOBOOT,BICROS (for BICROS unit) 16987500

BICROS UNIT 16987600

CROS CABLE 20 CM 7000-409





No need to change batt door

Remove AU cover to get access to the

4 contact points

Audio Boot for HIp/n 16987200

Connect the Audio Boot to the HI

Connect the Bicros Audio Boot to the Bicros Unit. Con-nect the two set with a cros cable in a suitable length

Both boots have 3 pin euro plug connection to fit the CROS cables

Open/close the batt door can still be done with the boot mounted

CROS/BICROS System

Doc 0194590 rev. C

of 11


Two plastic bolts holds on to the batt. door. Use a tweezer to separate them and pull them out. It is now possible to remove the door

Gently pull the two housing parts from each other

Plastic bolts Gently pull out the amplifier

Remove rec and mic from housing

HI Disassembly

Doc 0194590 rev. C

of 11


TC

Amplifier

Doc 0194590 rev. C

of 11


Add rubber glue to fix the wires

Connect wires and mount mic into suspension

The rec is delivered as rec complete in box as shown

Route wires and make sure to place correctly in HSG

Place Rec in front HSG. Solder Rec wires to amplifier and route them well when adding HSG parts

Note: Apply coating SL1367 material on solder pads after soldering

Replacement of Receiver & Microphone

Doc 0194590 rev. C

of 11


Place the VC into the VC coverVC cover Add the VC plate Mount VC to amplifier. Screw VC nut and solder the two VC terminals

Add glue in the grove for TC. Place TC into the grove. Connect TC wires to PCB and route them as shown

Note: Apply coating SL1367 material on solder pads after soldering

Replacement of Telecoil & VC

Doc 0194590 rev. C

of 11


When testing the HI the test ring is needed to stabilize the HI. Insert the hook to the tube and push up the test ring to fix the tube and hook. Connect the CS44 prog cable to HI and place the HI and 2cc coupler in the fixture

Test fixturep/n 16611100

HI inserted the fixture in test frame and placed in test chamber

CS44 Prog cable(Left blue is shown)9022 907 69019 (R)9022 907 69029 (L)

2cc coupler p/n 30-4838800 2cc coupler BTE insert p/n 40B4609601

to be ordered with GTO Dept/HQ Ballerup DK

Test & Test Equipment

Test frame p/n 16902800

Test ring attached the BTE coupler insert tube

Test ring p/n 15472600

Note: When testing the HI the test SW for AUDIOMASTER,SP90-VI (RS SPARX model) & INT PLF set must be used - available from GTO web site

Technical Manual INTERTON Elipse Digital...

Documents

Transcript of Technical Manual INTERTON Elipse Digital...