Global Technical Operations gto.gnresound.com
Lautrupbjerg 7 • DK-2750 Ballerup • DenmarkE-Mail: [email protected]
Technical ManualINTERTON
Elipse Digital SPBTE
Doc 0194590 rev. C
Page 2 of 11
Not subject to issue control when printed
Subject Page
Description ..................................................................................................... 3 Part List ......................................................................................................... 4 Part List - HSG Parts...................................................................................... 5 CROS/BICROS System ................................................................................. 6 HI Dissembly .................................................................................................. 7 Amplifier ......................................................................................................... 8 Replacement of Microphone & Receiver........................................................ 9 Replacement of VC & TC ............................................................................. 10 Test................................................................................................................11
Table of Contents
Doc 0194590 rev. C
Page 3 of 11
Not subject to issue control when printed
Description
Model Data Sheet
ELIPSE EL90-VI 17141700
Beige Brown Grey
Available in Beige, Brown & Grey
Doc 0194590 rev. C
Page 4 of 11
Not subject to issue control when printed
Item Part No
MIC. SUSPENSION 15297000
MICROPHONE 33M 15240900
MICROPHONE,COMPL 15988900WIRE,ESW,AMBER,7X32U,14MM 15129714
WIRE,ESW,GREEN,7X32U,14MM 15129814
WIRE,ESW,RED,7X32U,14MM 15129614
PLASTIC BOLT 15284000
REC COMPL. 15989200
AMPL COMPL 17188401
TELECOIL 16453100
VC NUT 15341000
VC COVER SILICONE 15282900VC PLATE 15283000VC 50K LINEAR PJ77 15751101
Item Part No
HI-PRO PROG. CABLE CS44, R 9022 907 69019
HI-PRO PROG. CABLE CS44, L 9022 907 69029
TEST RING 15472600
TEST FIXTURE 16611100
TEST FRAME 16902800*
CONFORMAL COATING SL1367 **
ADULT HOOK W/O FILTER 15353200
ADULT HOOK WITH FILTER 15418400
BABY HOOK WITH FILTER 15427800
BABY HOOK W/O FILTER 15350900
FILTER-GR BF 1999 70930834
* Test frame p/n 1-21-65900 can be used as well
**Conformal coating SL1367 peters coat to be purchased locally. Check **e.g. the vendor website http://www.peters.de
Part List
Doc 0194590 rev. C
Page 5 of 11
Not subject to issue control when printed
HSG Parts For HIBEIGE
For HIBROWN
For HIGREY
HSG PARTS TRANSP(optional)
AU COVER,PTD 16429100 16429101 16429105 16429103
AU COVER,PTD - BLUE** 16429104 16429104 16429104 -
AU COVER,PTD - RED** 16429106 16429106 16429106 -
BAT DR,PTD,CE-MARK,EL90 17366500 17366501 17366505 -
HSG,BACK (VC SIDE) 15339400 15339401 15339405 -
HSG,FR,PTD, EL90-VI 16729400 16729401 16729405 -
PC COVER,MOULDED 15339500 15339501 15339505 15339503
PC COVER,PTD,L** 16003100 16003101 16003105 16003103
PC COVER,PTD,R** 16003000 16003001 16003005 16003003
PB COVER 15893300 15893301 15893305 15893303
VC COVER PROTECTION (optional) 15427400 15427401 15427402 15427403
** To be mounted for indication of Right/Left side
VC cover optional(child protection cover)
Part List - HSG Parts
Doc 0194590 rev. C
Page 6 of 11
Not subject to issue control when printed
Description Part No
AUDIO-BOOT (for HI) 16987200
AUDIOBOOT,BICROS (for BICROS unit) 16987500
BICROS UNIT 16987600
CROS CABLE 20 CM 7000-409
CROS CABLE 22 CM 7000-439
CROS CABLE 24 CM 7000-469
CROS CABLE 26 CM 7000-459
CROS CABLE 28 CM 7000-479
No need to change batt door
Remove AU cover to get access to the
4 contact points
Audio Boot for HIp/n 16987200
Connect the Audio Boot to the HI
Connect the Bicros Audio Boot to the Bicros Unit. Con-nect the two set with a cros cable in a suitable length
Both boots have 3 pin euro plug connection to fit the CROS cables
Open/close the batt door can still be done with the boot mounted
CROS/BICROS System
Doc 0194590 rev. C
Page 7 of 11
Not subject to issue control when printed
Two plastic bolts holds on to the batt. door. Use a tweezer to separate them and pull them out. It is now possible to remove the door
Gently pull the two housing parts from each other
Plastic bolts Gently pull out the amplifier
Remove rec and mic from housing
HI Disassembly
Doc 0194590 rev. C
Page 8 of 11
Not subject to issue control when printed
TC
Amplifier
Doc 0194590 rev. C
Page 9 of 11
Not subject to issue control when printed
Add rubber glue to fix the wires
Connect wires and mount mic into suspension
The rec is delivered as rec complete in box as shown
Route wires and make sure to place correctly in HSG
Place Rec in front HSG. Solder Rec wires to amplifier and route them well when adding HSG parts
Note: Apply coating SL1367 material on solder pads after soldering
Replacement of Receiver & Microphone
Doc 0194590 rev. C
Page 10 of 11
Not subject to issue control when printed
Place the VC into the VC coverVC cover Add the VC plate Mount VC to amplifier. Screw VC nut and solder the two VC terminals
Add glue in the grove for TC. Place TC into the grove. Connect TC wires to PCB and route them as shown
Note: Apply coating SL1367 material on solder pads after soldering
Replacement of Telecoil & VC
Doc 0194590 rev. C
Page 11 of 11
Not subject to issue control when printed
When testing the HI the test ring is needed to stabilize the HI. Insert the hook to the tube and push up the test ring to fix the tube and hook. Connect the CS44 prog cable to HI and place the HI and 2cc coupler in the fixture
Test fixturep/n 16611100
HI inserted the fixture in test frame and placed in test chamber
CS44 Prog cable(Left blue is shown)9022 907 69019 (R)9022 907 69029 (L)
2cc coupler p/n 30-4838800 2cc coupler BTE insert p/n 40B4609601
to be ordered with GTO Dept/HQ Ballerup DK
Test & Test Equipment
Test frame p/n 16902800
Test ring attached the BTE coupler insert tube
Test ring p/n 15472600
Note: When testing the HI the test SW for AUDIOMASTER,SP90-VI (RS SPARX model) & INT PLF set must be used - available from GTO web site
Top Related