James Cock, Patricia Moreno Cadena, Mayra … · James Cock, Patricia Moreno Cadena, Mayra...
Transcript of James Cock, Patricia Moreno Cadena, Mayra … · James Cock, Patricia Moreno Cadena, Mayra...
James Cock, Patricia Moreno Cadena, Mayra Alejandra Toro, y Johanna Arango
Contents 1. INTRODUCTION .................................................................................................................... 1
2. OUR GOAL .............................................................................................................................. 1
3. MATERIALS ............................................................................................................................ 1
4. FIELD MEASUREMENTS...................................................................................................... 2
4.1 Sample size: ........................................................................................................................ 2
4.2 Frequency of monitoring: ................................................................................................... 2
First sample: ........................................................................................................................... 2
Weekly Monitoring: ............................................................................................................... 2
Fortnightly Monitoring: ......................................................................................................... 2
Monthly monitoring: .............................................................................................................. 2
4.3 Procedure ............................................................................................................................ 2
Record of germination ........................................................................................................... 2
A. Germination date: ........................................................................................................... 2
First sampling: ....................................................................................................................... 3
A. Selection of shoots to monitor: ..................................................................................... 3
B. Tickets: ........................................................................................................................... 3
Weekly monitoring ................................................................................................................ 5
A. Collection of tickets: ...................................................................................................... 5
B. Rate leaf formation: ........................................................................................................ 5
C. Height of plant:............................................................................................................... 6
Biweekly monitoring ............................................................................................................. 6
A. Count of nodes: .............................................................................................................. 6
B. Determination of the length and diameter of internodes: ............................................... 7
C. Identification of first fully expanded leaf: ...................................................................... 8
D. Determination of leaf area: ............................................................................................ 9
ANNEX 1: SAMPLE OF THE WORKSHEET TO REGISTER THE SAMPLING DATA ...... 11
ANNEX 2: DEVELOPMENT OF THE INSTRUMENT TO MEASURE LEAF AREA ........... 12
ANNEX 3: IMAGE PROCESSING WITH IMAGE J SOFTWARE .......................................... 17
List of Figures Figure 1. Record of germination at 14 days after planting ............................................................. 3
Figure 2. Plants with one (left) and two (right) shoots that grew from the originally sown stake . 3
Figure 3. Example of a ticket with the plot identification and the date .......................................... 4
Figure 4. Tickets with color coded with a different color for each date ......................................... 4
Figure 5. New ticket in the youngest leaf with a petiole separated stem ........................................ 4
Figure 6. Plant with large labels in contact with the ground (left) and plants with small labels
(right) .............................................................................................................................................. 5
Figure 7. Collection of the fallen tickets on the ground ................................................................. 5
Figure 8. First branching height measurement ............................................................................... 6
Figure 9. Dead apex ........................................................................................................................ 6
Figure 10. Identification of levels of branching.............................................................................. 7
Figure 11. Identification of sections according to the length of internodes. Branch with two
different sections identified (left) and branch with only a section identified (right). ..................... 7
Figure 12. Determination of the change in the branch, of green to lignified .................................. 8
Figure 13. Measurement of the stem diameter ................................................................................ 8
Figure 14. Angle between the petiole of fully expanded leaf and stem .......................................... 9
Figure 15. Size difference between an unexpanded and fully expanded leaf ................................. 9
Figure 16. Capture process of photography to the determination of leaf area: Identification of the
fully expanded leaf, insertion between the laminae and take photography .................................. 10
Figure 17. Position of the camera to take the picture ................................................................... 10
Annex 2
Figure 18. Materials used in preparing the template to measure leaf area ................................... 12
Figure 19. Shiny side (left) and dull side (right) of the lamina of polystyrene and acrylic .......... 12
Figure 20. Hinge location and marking plates .............................................................................. 13
Figure 21. Opening holes with the drill in the plates .................................................................... 13
Figure 22. Locations of screws a hinge and plate ......................................................................... 14
Figure 23. Assurance hinges on acrylic sheet ............................................................................... 14
Figure 24. Union of acrylic and polystyrene laminas. .................................................................. 15
Figure 25. Dialing scale ................................................................................................................ 15
Figure 26. Definition of grid ......................................................................................................... 16
Figure 27. Instrument to measure leaf area ................................................................................... 16
Annex 3
Figure 28. ImageJ installation ....................................................................................................... 18
Figure 29. Working window for ImageJ ....................................................................................... 18
Figure 30. Menu to open the image and emerging window ......................................................... 19
Figure 31. Straight icon from the principal menu of ImageJ ........................................................ 19
Figure 32. Scale definition according with the image .................................................................. 20
Figure 33. Image conversion to 8 bits ........................................................................................... 20
Figure 34. Image conversion to binary ......................................................................................... 21
Figure 35. Selection of the variable to measure, area ................................................................... 21
Figure 36. Menu Analyze particles ............................................................................................... 22
Figure 37. Results visualization for the images without shade and reflection .............................. 22
Figure 38. Threshold menu ........................................................................................................... 23
Figure 39. Menu to define hide, saturation and brightness properties .......................................... 23
Figure 40. Menu Analyze particles ............................................................................................... 24
Figure 41. Results visualization for images with shades and reflection ....................................... 24
1
1. INTRODUCTION This non-destructive method provides a means of monitoring the development of the cassava
crop under a range of biophysical environments without the need to plant trials specifically
for this purpose. The plots established or commercial lots can be monitored nondestructively:
therefore any parcel can be monitored. The methodology collects data on the development of
the cassava crop and can use this data in understanding the development of the crop, and also
to generate, validate and improve the robustness of simulation models cassava. This is the
first approximation of the methodology; we encourage users to voice any concerns and
suggest ways of improving the non-destructive monitoring system.
2. OUR GOAL To improve our understanding of the physiological development of cassava through detailed
recording of cassava growth during all stages of its development under a range of conditions.
The information and understanding generated can be used to improve cassava growth and
simulation models.
3. MATERIALS a) Vernier caliper
b) Tape measure/ ruler
c) Forms for recording information (Annex 1)
d) Labels or tags with string for marking leaves
e) Pencil
f) Permanent marker
g) An instrument for measuring leaf area in field (Annex 2)
h) Camera
i) Computer
A B D E F
H I
2
4. FIELD MEASUREMENTS
4.1 Sample size: five representative plants for each treatment or variety should be monitored.
All monitored plants should be surrounded by at least one border plant.
4.2 Frequency of monitoring: After the first sampling, the plots should be monitored at
fixed intervals. When monitoring is very frequent great care must be taken not to compact the
soil, especially during the rainy season. The sampling frequency may be varied with some
weekly, biweekly or monthly intervals up to monitoring and measuring certain variables in
each of these:
First sample: For this monitoring germination date must be pre-defined, and a shoot
should be selected to be followed during the development of the plant; additionally must
identify the youngest leaf with a petiole separated stem to identify with a ticket and start
the evaluation of the rate of leaf formation.
Weekly Monitoring: The variables to be measured every week are the rate of formation
of leaves, leaf longevity through ticket collection; and plant height. These variables are
measured at this frequency because they are more dynamic and more change with the
development of the plant, with significant differences between one week and one; also do
not require much time in the field to be determined.
Fortnightly Monitoring: The variables that should be measured every two weeks are the
number of nodes, length and diameter of internodes, the identification of the first fully
expanded leaf and leaf area of this. These variables require more time in the field to be
determined.
Monthly monitoring: The variable to be measured monthly, is the total apex number,
taking into account live and dead apices
If a sampling date is missed due to unforeseen problems continue with the sampling as soon as
possible after the missed sample: the data can still be used. In this case, the variables are
measured each week can be measured biweekly and these in turn on a monthly basis.
4.3 Procedure
Record of germination
A. Germination date: Monitor the crop every 5 days after planting to observe the date
when the first shoots appear from the original planting piece or cutting (Figure 1).
Evaluate at least twenty plants if possible and when 50% of the cuttings have germinated
with new green shoots emerging, record the date of germination. Record the germination
data in the form established for the first sampling (ANNEX 1).
3
Figure 1. Record of germination at 14 days after planting
First sampling:
A. Selection of shoots to monitor: When 50 % of the plants have germinated and the first
leaves are fully expanded that the petiole is clearly visible and separates the leaf from
stem, select five representative plants in each plot or field. Count and record the number
of shoots on each of the plants selected to be monitored in ANNEX 1 (column D). For
each plant select at random one of the shoots (Figure 2).
Figure 2. Plants with one (left) and two (right) shoots that grew from the originally sown stake
B. Tickets: Label the tickets with the plot identification, and the date (Figure 3). These
tickets can be color coded with a different color for each date of placement to facility
later collection of fallen tickets (Figure 4). On the selected shoot of each plant hang a
ticket on the highest leaf on which the ticket can easily be placed; note that this leaf is
never expanded (Figure 5). Count the number of existing leaves to this leaf. When plants
are very small it is advisable to use small tickets that do not damage the plant and are not
in contact with the soil (Figure 6).
4
Figure 3. Example of a ticket with the plot identification and the date
Figure 4. Tickets with color coded with a different color for each date
Figure 5. New ticket in the youngest leaf with a petiole separated stem
5
Figure 6. Plant with large labels in contact with the ground (left) and plants with small labels (right)
Weekly monitoring
A. Collection of tickets: On entering the field for both weekly, two weekly or monthly
monitoring the fallen leaves or tickets on the ground are collected (Figure 7). The date of
collections is recorded (ANNEX 1, column E). If you cannot verify the information on
the ticket because the label is in illegible due to its poor condition, it should be possible
estimate the original placement date considering the dates on which have been monitored
plants and checking in tickets that are still in the shoot date is missing. As mentioned
earlier, color coding of the tickets also aids ticket date identification.
Figure 7. Collection of the fallen tickets on the ground
B. Rate leaf formation: After the first sample, count the number of new leaves starting
from leaf to put the ticket on the last visit to the new youngest leaf with a petiole
separated stem. At each visit, do the same process by recording the number of new leaves
(ANNEX 1, Column F).
6
C. Height of plant: With a meter stick measure the height of the plant from the ground to
the leaf that is at the plants highest point and also measure the height from the ground to
the first branching (Figure 8) (ANNEX 1, column J and K).
A.
Figure 8. First branching height measurement
Biweekly monitoring
A. Count of nodes: After the first sampling should also count the number of new nodes
starting from the node that holds the ticket that was put on the last visit. Must count up
and check if in the process find a branch point or a dead apex. If you encounter a branch
point record the number of nodes up to the branch point (from the last ticket) (ANNEX 1,
Column O), and the number of branches at the branch point. (ANNEX 1, column I).
Randomly select one of the branches and continue as previously. If you encounter a dead
apex (Figure 9), record the dead apex (ANNEX 1, Column F) and return to the last
branching point, select another branch and continue the process as before. The counting
of nodes stops at the highest point where a label can easily be hung on the youngest leaf
with a petiole separated stem. Hang a new ticket on this leaf and petiole.
Figure 9. Dead apex
7
B. Determination of the length and diameter of internodes: Identify the branching
levels of the plant according to (Figure 10) and record the number of branching levels
(ANNEX 1, column H). These branching levels should be the same as those determined
when counting the number of nodes and branch points and can be easily viewed
following down the stem from the last ticket that was placed at the plant. At each level of
branching, divide each of the shoots monitored in sections, with each section
corresponding to a distinct distance between nodes, or internode length (Figure 11).
Generally, the first internodes of each branching level have a different length to the
others and should be treated as a separate section. To facilitate identification of the
sections at later monitoring visits the lignified sections can be identified by permanent
marker.
Figure 10. Identification of levels of branching
Figure 11. Identification of sections according to the length of internodes. Branch with two different sections
identified (left) and branch with only a section identified (right).
First level of branching
2 Shoots
Second level of branching
3 Shoots
8
In each of the distinct stems sections:
Record the branch level
Record if the section is green or lignified (Figure 12) (ANNEX 1, column M)
Count and record the number of nodes in the section as the number of nodes from the
last branch (ANNEX 1, column O)
Measure and record the length of the section (ANNEX 1, column Q)
Measure the diameter in the middle of the section with the Vernier caliper (Figure 13)
(ANNEX 1, column P)
Figure 12. Determination of the change in the branch, of green to lignified
Figure 13. Measurement of the stem diameter
C. Identification of first fully expanded leaf: Try to get to the field early in the morning
so as to avoid too much sun and can easily identify in the shoot is monitored the first
fully expanded leaf. Generally as you move down the stem of the plant you will find each
successive leaf is larger than the previous leaf, until you reach a point where several
9
leaves are more or less of the same size. The first of these leaves of similar size from the
top down is taken as the first fully expanded leaf.
This leaf must be complete, must not show any damage to the laminae and can be easily
identified by considering factors such as the angle between the petiole and stem and the
angle between leaf laminae and the petiole (Figure 14), color between the petiole and leaf
laminae and size (Figure 15). Usually, close to the branching point there are one or two
small, but fully expanded leaves. Do not use these leaves for leaf area measurement.
Figure 14. Angle between the petiole of fully expanded leaf and stem
Figure 15. Size difference between an unexpanded and fully expanded leaf
D. Determination of leaf area: Once the fully expanded leaf has been identified, the leaf
area is determined using the leaf area apparatus (LAA) described in the appendix. Insert
10
the first fully expanded leaf, still attached to the plant, between the two laminae of the
LAA. Care should be taken to ensure that the leaf is not damaged (Figure 16).
Figure 16. Capture process of photography to the determination of leaf area: Identification of the fully expanded
leaf, insertion between the laminae and take photography
Once the leaf is between the laminae take a photograph of the leaf in the LAA with the
camera held vertically above the LAA (Figure 17). A label should be placed in the LAA
to identify the photograph later. We have found that one person, with practice, can place
the leaf in the apparatus and take the photograph, however this takes practice. Hence, we
strongly advise practicing this procedure before monitoring and when possible having an
assistant in the field. The instructions to determine the leaf area are in the Annex 3.
Figure 17. Position of the camera to take the picture
Monthly monitoring
A. Total Apex number: Finally count the total number of live and dead apices on each
plant and record them.
11
ANNEX 1: SAMPLE OF THE WORKSHEET TO REGISTER THE SAMPLING DATA
SAMPLING
DATE GERMINATION
DATE
LOCATION CIAT
19/05/2014
31/03/2014
A B C D E F G H I J K L M N O P Q
Cu
ltiv
ar Plant ID
No
. of
sho
ots
pe
r
cutt
ing
Leaves longevity
Rate of leaf formation
No
. of
leve
ls o
f
bra
nch
ing
No
. of
bra
nch
es
pe
r
bra
nch
po
int Height Length and diameter of internodes
Blo
ck
Pla
nt
ID
Collection date
No. new
leaves
No. dead apexes
Plant height (cm)
Shoot height (cm)
No. branch
Part of the branch
Section Branch
No. de
nodes
Stem diameter
(cm)
Stem length (cm)
HMC1 1 1 3 23/04/2014 5 0 1 2 57 36 1 Lignified 1 3 5,0 11,92
1 Lignified 2 5 7,8 12,57
1 Unlignified 3 13 14,0 13,39
1 Unlignified 4 7 20,2 10,42
1,1 Unlignified 1 1 5,5 4,17
1,1 Unlignified 2 2 2,5 3,49
HMC1 1 2 2 16/04/2014 6 0 0 3 46 -- 1 Lignified 1 7 10,0 9,68
1 Lignified 2 12 12,4 10,15
1 Unlignified 3 8 12,5 9,62
12
ANNEX 2: DEVELOPMENT OF THE INSTRUMENT TO MEASURE LEAF AREA A. MATERIALS (Figure 18)
1 Ruler
1 lamina of acrylic, antiglare, glass color, 2mm thick and measures 35 x 35 cms
1 lamina of black or red polystyrene, 2mm thick and measures 35 x 35 cms
2 Hinges
1 Drill
1 Scoreboard thin tip
1 Pencil
Figure 18. Materials used in preparing the template to measure leaf area
B. PROCEDURE
Make sure you are using the laminas on the right side. The two laminas have a shiny side
and a dull side (Figure 19), so that the shiny side should be placed down and dull side up,
in order to avoid reflections at the time of taking the photograph.
Figure 19. Shiny side (left) and dull side (right) of the lamina of polystyrene and acrylic
Join the two laminas with the hinges. Place one side of the hinges on the acrylic lamina in
the desired position, and with a marker, paint points through which the screws should enter
(Figure 20).
13
Figure 20. Hinge location and marking plates
Subsequently, with the drill, open the holes through which will pass the screws at two sides
of the lamina. Make sure you have all the tools and security necessary to use the drill
(Figure 21).
Figure 21. Opening holes with the drill in the plates
Locate the hinge on the holes made previously and insert the screws that come with the
hinge, securing each one with nuts (Figure 22).
14
Figure 22. Locations of screws a hinge and plate
The result on the acrylic lamina is a hinge side installed, and secured with screws and nuts
(Figure 23).
Figure 23. Assurance hinges on acrylic sheet
Then, place the other side of the hinges on the red polystyrene lamina painting the points
where the screws must enter. Then, with the drill open the holes and join both laminas
(Figure 24).
15
Figure 24. Union of acrylic and polystyrene laminas.
Finally, create the scale that will be used in the pictures in cm, on the red polystyrene
lamina. For this, initially, with a ruler, draw a scale of approximately 6 cm in two corners
of the lamina in pencil. Then use a non-erasable marker to accentuate the scale (Figure 25).
Figure 25. Dialing scale
16
In the case where there is no availability of a computer with the software to analyze the
images, a grid in the acrylic lamina can be generated with a known distance between each
line, for example 2cm in length. Thus, when placing the leaf under the grid, one can easily
count the number of squares occupied by the leaf being measured, and therefore provide an
indication of the leaf area that you have (Figure 26).
.
Figure 26. Definition of grid
The end result of the process is the union of the two laminas with a hinge at each corner,
the polystyrene lamina with a scale and if necessary, the acrylic sheet with a grid. This
instrument facilitates taking photographs to determine the leaf area because it is easy to
transport, does not create reflections when taking the picture and can be opened and closed
as many times as necessary without risk of damage (Figure 27).
Figure 27. Instrument to measure leaf area
17
ANNEX 3: IMAGE PROCESSING WITH IMAGE J SOFTWARE
ImageJ is a program that makes use of digital image processing in Java, it is public domain and
easy to use. You can run ImageJ through JAVA online or on any computer via the Java virtual
machine; please note that ImageJ is downloadable for different computer operating systems. The
program enables the user to view, edit, analyze, process and save images of 8, 16 and 32 bits;
furthermore it reads many image formats. ImageJ allows the user to make simple and
multithreaded operations on the images and run the program for any purpose, studying how it
works and changing it according to the intended need, it also allows the user to redistribute
copies and add improvements to the program which can then be available to the public.
A. INSTALLATION AND IMPLEMENTATION OF IMAGE J
This application is free; download and run the file for your operating system from the following
link: http://imagej.nih.gov/ij/ selecting the download option. When the installation window is
opened, select the location of the folder where you want to save the program files, and the
additional icons that you want to install (Figure 28).
18
Figure 28. ImageJ installation
B. IMAGE PROCESSING
Once it is installed, you can access the program from the icon that was installed on the
desktop or through Start, selecting All Programs, and then Image J. When the program is
opened, the following window will appear which is the taskbar main program and consists of
several menus and various buttons (Figure 29).
Figure 29. Working window for ImageJ
To open an image, select the File menu, then select the Open option and in the dialog box
choose the image that you want to open (Figure 30). The image should have a scale that uses a
known distance to define the scale of photography; this is defined by the distance in pixels in
accordance with the distance of the real scale.
19
Figure 30. Menu to open the image and emerging window
Now that you have opened the image, we are ready to start the analysis process. Select with
the cursor the icon Straight in the taskbar, it has a diagonal line with a red arrow. Then select
a known distance according to the scale of the image (Figure 31).
Figure 31. Straight icon from the principal menu of ImageJ
Subsequently, in the Analyze menu select the option Set scale. A table will now open showing
the distance in pixels from the previously plotted line. Thus, having knowledge of the real
length of this distance, the scale of the photograph is defined through the evaluation of the
size of a pixel in cm. In the Known Distance box enter the real length of the selected line and
in the box Unit of length enter the units for this distance. Select the Global option at the
bottom of the table; afterwards, if you analyze other images you will just have to modify the
distance in pixels that represents a known unit of measurement (Figure 32).
20
Figure 32. Scale definition according with the image
Afterwards, you have to convert the color image to grayscale by selecting in the Image menu,
the options of Type and 8 bits (Figure 33). Then, go to the Process menu and select the Binary
option and finally Make binary option (Figure 34). Additionally, you have to select the
variables that you want to analyze in the image by selecting the Analyze menu, Set
Measurements option and verifying that only the area box is checked because it is the
variable that we want to calculate, then select Ok (Figure 35).
Figure 33. Image conversion to 8 bits
21
Figure 34. Image conversion to binary
And now select in the Analyze menu, the Analyze Particles option and in the Size box set the
unit of measure of the scale of the original image. The Pixel units option should not be
checked, the Circularity option must be filled with the number one (1) and the Show option
should display the word Nothing. Next, mark the following options; results display, Clear
results, Include holes and Add to manager (Figure 36).
Figure 35. Selection of the variable to measure, area
22
Figure 36. Menu Analyze particles
Observing the image, we find a number of polygons, with our main interest being the one
with the largest area. Additionally, the Results window shows the area of the polygons
identified in the image. With the ROI Manager window you can select the number of the
polygon of interest (first 4 digits); when you select the correct polygon, its outline will take a
different color in comparison with others (Figure 37).
Figure 37. Results visualization for the images without shade and reflection
23
C. IMAGE PROCESSING WITH SHADOWS
When you take the picture of the leaf, depending on the light’s intensity and location, it is
possible that the image has shadows or reflections that interfere with the analysis. If this
happens you must follow another methodology to analyze the image. In this case, after defining
the scale according to the last explanation, you have to select in the Image menu the adjust
option and then the Threshold option (Figure 38).
Figure 38. Threshold menu
In this section the properties of hue, saturation and brightness are set, then the threshold to fit
only the shape or contour of the leaf to be analyzed should be selected (Figure 39). Next, select
in the Analyze menu, the Analyze Particles option, the size box should be filled with letters 0.1 to
Infinity, Pixel units option should not be checked, the Circularity option must be filled with the
numbers 0-1 and the Show option should be displaying the word Nothing. Next, mark the
options; results display, Clear results, Include holes and Add to manager (Figure 40).
Figure 39. Menu to define hide, saturation and brightness properties
Reflejo
24
Again, observing the image, we find a number of polygons, and as before, our main interest is
in the one with the largest area. Additionally, the Results window shows the area of the
polygons identified in the image. With the ROI Manager window you can select the number
of polygons that are of interest (first 4 digits); when you select the correct polygon, its outline
will take a different color in comparison with others (Figure 41).
Figure 40. Menu Analyze particles
Figure 41. Results visualization for images with shades and reflection
25
Finally, in the Results window, export the results as an Excel table by selecting in the File
menu the Save As option. When you open the saved Excel file, you can access the data of leaf
area which will be used as part of the non-destructive methodology for the cassava crop.
26