EXPANDED METAL PLASTERING ACCESSORIES metal.pdf · EXPANDED METAL PLASTERING ACCESSORIES 2 ISO...
Transcript of EXPANDED METAL PLASTERING ACCESSORIES metal.pdf · EXPANDED METAL PLASTERING ACCESSORIES 2 ISO...
1
for Building & Construction Materials
EXPANDED METAL
PLASTERING ACCESSORIES
for Building & Construction Materials
Specialized Factory for Steel ProductsSigma Factory for Steel Products
SA09/21158
8
1-4-SEL03-M11
EXPANDED METALPLASTERING ACCESSORIES
2
ISO CERTIFICATES
• For inside applications: Galvanized Steel according to BS EN 10327 superseded by BS EN 10346:2009, zinc coated on both sides.• For outside applications and humid environment: Austenitic stainless steel according to BS EN 10088- Mat.No.1.4301
Technical Specifications
Metal Beads Relevant Standards:• BS EN 13914- 2 : 2005 Design , Preparation and Application of External Rendering and Internal Plastering• BS EN 13658-1 : 2005 Metal Lath and Beads – Definitions , Requirements and Test Methods , Internal Plastering
Supersedes BS 1369-1 :1987 and BS 6452-1 : 1984• BS EN 13658 – 2 : 2005 Metal Lath and Beads – Definitions , Requirements and Test Methods , External Plastering Supersedes BS 1369-2 :1987 and BS 6452-2 : 1984 • ASTM C841 – Standard Specification for Installation of Interior Lathing and Furring• ASTM C847 – Standard Specification for Metal Lath• ASTM C1063 – Standard Specification for Installation of Lathing and Furring for Portland Cement – Based Plaster• International Building Code , ( IBC ) Chapter 25• International Residential Code , ( IRC ) Chapter 7
Galvanized Steel:• BS EN 10346:2009 (formerly BS EN 10142: 1991) coating type: Z180-275 ASTM A 653/A 653M
Stainless Steel:• BS EN 10088-2:2005 (which was directly equivalent to formerly BS 1449:Part 2:1983 in Grade 304 2B FINISH• ASTM A240/A240M in Grade 304 2B FINISH
Expanded Metal Lath & Block Work Expanded MeshRelevant Standards:• BS EN 13658-1 & 2:2005 (formerly BS 1369:Part 1:1987)• ASTM C 847
Galvanized Steel:• BS EN 10346:2009 (formerly BS EN 10142:1991) coating type:
Z180-275• ASTM A 653/A 653M
Stainless Steel:• BS EN 10088-2:2005, which was directly equivalent to formerly BS 1449:Part 2:1983 in Grade 304 2B FINISH• ASTM A240/A240M in Grade 304 2B FINISH
Reiforcement MeshRelevant Standards:• BS EN 845-3:2003 ASTM A 951/A 951M
Cold drawn steel for concrete/mansonry reinforcement• BS 4482:2005 ASTM A 496/A 496M, ASTM A 82/A 82M
Pre galvanized steel wire• BS EN 10244-2:2001 formerly BS 443 ASTM A 641/A 641M
Stainless Steel wire• BS EN 10088-3:2005 (which was direct equivalent to formerly
BS 1554:1990) BS 1449:Part 2:1983 in Grade 304 2B FINISH ASTM A 1022/A 1022M
ProductsUni-Metal expanded metal and accessories from SFSP are manufactured in compliance with international standards.
Uni-Metal provides a wide range of products capable of providing the characteristics which respond to the proposed application, along with quality of assembly, speed of installation and cost-saving expanded metal.
3
Angle Bead
Plaster Stop Bead
Movement Bead
Angle beads provide with its solid metal nose a straight corner. Expanded diamond mesh wings allow for keying the plaster right up to the nose of the bead. It is designed to protect the corners. The flanges can be easily fixed over irregular, uneven surfaces. Available in galvanized finish for internal use, and in stainless steel for external use.
Plaster stop bead provides a straight accurate line, it is used to reinforce the plaster or render on its edge. Plaster stop bead is designed as a universal plaster stop used at wall ends, door and window openings to make a neat, flush frame.
Movement Beads are used to relieve the stress and strain in large plaster areas of wall and ceiling stucco areas and to allow for movement between adjoining surface finishes. Movement Beads overcome movement tolerance in plaster and render finishes and minimize the cracking in plaster.
Reference Plaster Depth
(mm)
Material Length (mm) Qty / Box
PST 10 - GS 10 Galvanized 2700, 2850, 2900, 3000 50 Pieces
PST 13 - GS 13 Galvanized 2700, 2850, 2900, 3000 50 Pieces
PST 16 - GS 16 Galvanized 2700, 2850, 2900, 3000 50 Pieces
PST 19 - GS 19 Galvanized 2700, 2850, 2900, 3000 50 Pieces
PST 10 - SS 10 Stainless Steel 2700, 2850, 2900, 3000 50 Pieces
PST 13 - SS 13 Stainless Steel 2700, 2850, 2900, 3000 50 Pieces
PST 16 - SS 16 Stainless Steel 2700, 2850, 2900, 3000 50 Pieces
PST 19 - SS 19 Stainless Steel 2700, 2850, 2900, 3000 50 Pieces
Reference Plaster Depth
(mm)
Material Length (mm) Qty / Box
MBE 10 - GS 10 Galvanized 2700, 2850, 3000 50
MBE 13 - GS 13 Galvanized 2700, 2850, 3000 50
MBE 16 - GS 16 Galvanized 2700, 2850, 3000 50
MBE 19 - GS 19 Galvanized 2700, 2850, 3000 50
MBE 10 - SS 10 Stainless Steel 2700, 2850, 3000 50
MBE 13 - SS 13 Stainless Steel 2700, 2850, 3000 50
MBE 16 - SS 16 Stainless Steel 2700, 2850, 3000 50
MBE 19 - SS 19 Stainless Steel 2700, 2850, 3000 50
ReferenceLength of
wings (mm)
Plaster Depth (mm)
Material Length (mm)Qty /
Wooden Pallets
ABE 45 - GS 45 10-13 Galvanized 2700, 2850, 3000 100 Pieces
ABE 50 - GS 50 12-19 Galvanized 2700, 2850, 3000 100 Pieces
ABE 60 - GS 60 12-19 Galvanized 2700, 2850, 3000 75 Pieces
ABE 64 - GS 64 19 Galvanized 2700, 2850, 3000 75 Pieces
ABE 70 - GS 70 19 Galvanized 2700, 2850, 3000 75 Pieces
ABE 75 - GS 75 19 Galvanized 2700, 2850, 3000 75 Pieces
ABE 45 - SS 45 10-13 Stainless Steel 2700, 2850, 3000 100 Pieces
ABE 50 - SS 50 12-19 Stainless Steel 2700, 2850, 3000 100 Pieces
ABE 60 - SS 60 12-19 Stainless Steel 2700, 2850, 3000 75 Pieces
ABE 64 - SS 64 19 Stainless Steel 2700, 2850, 3000 75 Pieces
ABE 70 - SS 70 19 Stainless Steel 2700, 2850, 3000 75 Pieces
ABE 75 - SS 75 19 Stainless Steel 2700, 2850, 3000 75 Pieces
EXPANDED METALPLASTERING ACCESSORIES
4
Control Joint Bead
Aluminum Channel
Architrave Bead
Designed to minimize the plaster cracking and to allow movement in the plaster. Control Joint Bead overcomes movement tolerances in plaster Expansion / Control joints provide excellent expansion control for both walls and ceiling and offers positive locking of the stucco to the edge of the joint.
The Aluminum Channel is a versatile product, commonly used for groove making; a decorative purpose for plaster finishes.
Mainly used for decorative purposes to give a channel gap or a shadow between different walls finishes.
Reference Plaster Depth
(mm)
Material Length (mm) Qty / Box
CJB 10 - GS 10 Galvanized 2700, 2850, 3000 50 Pieces
CJB 13 - GS 13 Galvanized 2700, 2850, 3000 50 Pieces
CJB 16 - GS 16 Galvanized 2700, 2850, 3000 50 Pieces
CJB 19 - GS 19 Galvanized 2700, 2850, 3000 50 Pieces
CJB 10 - GS 10 Stainless Steel 2700, 2850, 3000 50 Pieces
CJB 13 - GS 13 Stainless Steel 2700, 2850, 3000 50 Pieces
CJB 16 - GS 16 Stainless Steel 2700, 2850, 3000 50 Pieces
CJB 19 - GS 19 Stainless Steel 2700, 2850, 3000 50 Pieces
Reference Size (mm) Material Length (mm) Thickness (mm)
CAL - 10 10x10x10 Aluminum 6000 1.5
CAL - 17 11x17x11 Aluminum 6000 1.5
CAL - 20 10x20x10 Aluminum 6000 1.5
CAL - 23 12.5x23x12.5 Aluminum 6000 1.5
Reference Plaster Depth (mm) Material Length (mm) Qty / Box
ACB 10 - WFG With flange 10 Galvanized 2700, 2850, 3000 50
ACB 13 - WFG With flange 13 Galvanized 2700, 2850, 3000 50
ACB 16 - WFG With flange 16 Galvanized 2700, 2850, 3000 50
ACB 19 - WFG With flange 19 Galvanized 2700, 2850, 3000 50
ACB 10 - WOG Without flange 10 Galvanized 2700, 2850, 2900, 3000 50
ACB 13 - WOG Without flange 13 Galvanized 2700, 2850, 2900, 3000 50
ACB 16 - WOG Without flange 16 Galvanized 2700, 2850, 2900, 3000 50
ACB 19 - WOG Without flange 19 Galvanized 2700, 2850, 2900, 3000 50
ACB 10 - WFS With flange 10 Stainless Steel 2700, 2850, 3000 50
ACB 13 - WFS With flange 13 Stainless Steel 2700, 2850, 3000 50
ACB 16 - WFS With flange 16 Stainless Steel 2700, 2850, 3000 50
ACB 19 - WFS With flange 19 Stainless Steel 2700, 2850, 3000 50
ACB 10 - WOS Without flange 10 Stainless Steel 2700, 2850, 2900, 3000 50
ACB 13 - WOS Without flange 13 Stainless Steel 2700, 2850, 2900, 3000 50
ACB 16 - WOS Without flange 16 Stainless Steel 2700, 2850, 2900, 3000 50
ACB 19 - WOS Without flange 19 Stainless Steel 2700, 2850, 2900, 3000 50
With flange Without flange
5
Reference Plaster Depth
(mm)
Material Length (mm) Qty / Box
MPS 03 - GS 3 Galvanized 2700, 2850, 2900, 3000 50 Pieces
MPS 06 - GS 6 Galvanized 2700, 2850, 2900, 3000 50 Pieces
MPS 03 - SS 3 Stainless Steel 2700, 2850, 2900, 3000 50 Pieces
MPS 06 - SS 6 Stainless Steel 2700, 2850, 2900, 3000 50 Pieces
Reference Plaster Depth
(mm)
Material Length (mm) Qty / Box
SMH 10 - GS 100 Galvanized 2440/3000 50 Pieces
SMH 15 - GS 150 Galvanized 2440/3000 50 Pieces
SMH 20 - GS 200 Galvanized 2440/3000 50 Pieces
SMH 30 - GS 300 Galvanized 2440/3000 50 Pieces
SMH 40 - GS 400 Galvanized 2440/3000 50 Pieces
SMH 10 - SS 100 Stainless Steel 2440/3000 50 Pieces
SMH 15 - SS 150 Stainless Steel 2440/3000 50 Pieces
SMH 20 - SS 200 Stainless Steel 2440/3000 50 Pieces
SMH 30 - SS 300 Stainless Steel 2440/3000 50 Pieces
SMH 40 - SS 400 Stainless Steel 2440/3000 50 Pieces
Micro Angle Bead
Micro Plaster Stop Beads
Strip Mesh
Micro angle beads are designed for thin coat plaster and are used at corners for protection. Micro angle beads are popular thin coat beads with fine mesh wings.Fix either by galvanized nails or using plaster dabs.
Micro plaster stops are designed for thin coat edge protection at openings. They provide abutment of plastered areas of other wall finishes. Micro plaster stops provide efficient keying and excellent finishes.
Micro plaster stops make neat, flush frames for windows and other openings.
Strip Mesh Lathes are used along stress lines where cracking is likely. Strip mesh provides reinforcement to the plaster to prevent crack over joints of different materials.
Reference Wing
Width
(mm)
Plaster
Depth(mm)
Material Length (mm) Qty / Box
MAB 04 - GS 25x25 4 Galvanized 3000 50 Pieces
MAB 06 - GS 30x30 6 Galvanized 3000 50 Pieces
MAB 04 - SS 25x25 4 Stainless Steel 3000 50 Pieces
MAB 06 - SS 30x30 6 Stainless Steel 3000 50 Pieces
EXPANDED METALPLASTERING ACCESSORIES
6
Coil Lath
Corner Mesh
BR. Mesh
An easy to fix lath, provides a secure key for plaster and render applications as well as offering effective joint and crack reinforcement.
Corner mesh lathes are used to prevent cracking in the plaster.
Block reinforcement meshes are produced for brick and block work reinforcement. Their primary usage is to prevent cracking. Embedded in the normal thickness of a brickwork joint, brick reinforcement meshes reduce the detrimental effects of vibration and changes of temperature. Brick reinforcement meshes increase resistance to tensional stress.
Reference Coil Lath Width (mm) Material Length (m)
CLH 10 - GS 100 Galvanized 50/100
CLH 15 - GS 150 Galvanized 50/100
CLH 20 - GS 200 Galvanized 50/100
CLH 30 - GS 300 Galvanized 50/100
CLH 40 - GS 400 Galvanized 50/100
CLH 10 - SS 100 Stainless Steel 50/100
CLH 15 - SS 150 Stainless Steel 50/100
CLH 20 - SS 200 Stainless Steel 50/100
CLH 30 - SS 300 Stainless Steel 50/100
CLH 40 - SS 400 Stainless Steel 50/100
ReferenceBR Mesh
Width (mm)
Block Width
(mm)Material Length (m) Qty / Box
BRM 50 - GS 50 100 Galvanized 50/100 50 Pieces
BRM 75 - GS 75 100 Galvanized 50/100 50 Pieces
BRM 100 - GS 100 150 Galvanized 50/100 50 Pieces
BRM 125 - GS 125 150 Galvanized 50/100 50 Pieces
BRM 150 - GS 150 200 Galvanized 50/100 50 Pieces
BRM 175 - GS 175 200 Galvanized 50/100 50 Pieces
BRM 200 - GS 200 250 Galvanized 50/100 50 Pieces
BRM 250 - GS 250 300 Galvanized 50/100 50 Pieces
BRM 300 - GS 300 350 Galvanized 50/100 50 Pieces
BRM 50 - SS 50 100 Stainless Steel 50/100 50 Pieces
BRM 75 - SS 75 100 Stainless Steel 50/100 50 Pieces
BRM 100 - SS 100 150 Stainless Steel 50/100 50 Pieces
BRM 150 - SS 150 200 Stainless Steel 50/100 50 Pieces
BRM 175 - SS 175 200 Stainless Steel 50/100 50 Pieces
BRM 200 - SS 200 250 Stainless Steel 50/100 50 Pieces
BRM 250 - SS 250 300 Stainless Steel 50/100 50 Pieces
BRM 300 - SS 300 350 Stainless Steel 50/100 50 Pieces
Reference Length of wings
(mm)
Material Length (mm) Qty / Box
CRM 50 - GS 50 x 50 Galvanized 2440, 3000 100 Pieces
CRM 75 - GS 75 x 75 Galvanized 2440, 3000 100 Pieces
CRM 50 - SS 50 x 50 Stainless Steel 2440, 3000 100 Pieces
CRM 75 - SS 75 x 75 Stainless Steel 2440, 3000 100 Pieces
7
Metal Sheet Lath
Metal Rib Lath
Hy-Rib Lath
Sheet lath is produced as a key for plaster when applied on suspended ceiling and walls. Sheet lath is used for encasing steel column and beams, assisting in the protection from fire. Sheet lath is used to reinforce plaster between dissimilar areas and at crack-prone areas adjacent to openings.
Rib lathes are expanded metal lathes stiffened with longitudinal ribs. The furring design of the mesh provides efficient background plaster for construction of partition, suspend ceiling and refurbishment works. Rib lath is ideal for refurbishing damaged or old masonry walls, when a key for rendering is not certain due to disintegration or softening of the wall face.
Manufactured from Pre-galvanized steel to BSEN 10327.Hy Rib is available using stainless steeI to BSEN 10088-2 type 1 .4301 . The profile of Hy Rib open mesh in combination with its ribs provide an inherently stiff sheet along its length. It can be used for flat and curved surfaces.
Reference Weight (Kg/m2) Material Dimension (mm)
SHL 064 - GS 0.64 Galvanized 2440 x 600
SHL 082 - GS 0.82 Galvanized 2440 x 600
SHL 105 - GS 1.05 Galvanized 2440 x 600
SHL 122 - GS 1.22 Galvanized 2440 x 600
SHL 162 - GS 1.62 Galvanized 2440 x 600
SHL 190 - GS 1.90 Galvanized 2440 x 600
SHL 064 - SS 0.64 Stainless Steel 2440 x 600
SHL 082 - SS 0.82 Stainless Steel 2440 x 600
SHL 105 - SS 1.05 Stainless Steel 2440 x 600
SHL 122 - SS 1.22 Stainless Steel 2440 x 600
SHL 162 - SS 1.62 Stainless Steel 2440 x 600
SHL 190 - SS 1.90 Stainless Steel 2440 x 600
Reference Weight (kg/m2) Material Size (mm) Rib Height (mm)
RBL 148 - GS 1.48 Galvanized 2500 x 700 10
RBL 184 - GS 1.84 Galvanized 2500 x 700 10
RBL 222 - GS 2.22 Galvanized 2500 x 700 10
RBL 148 - SS 1.48 Stainless Steel 2500 x 700 10
RBL 184 - SS 1.84 Stainless Steel 2500 x 700 10
RBL 222 - SS 2.22 Stainless Steel 2500 x 700 10
Thickness
(mm)
Width
(mm)
Rib Height
(mm)
Rib Distance (mm) Length
0.25 445 13 89 According to Order
0.3 445 13 89 According to Order
0.3 445 20.5 89 According to Order
0.35 445 13 89 According to Order
0.35 445 20.5 89 According to Order
0.4 445 13 89 According to Order
0.4 445 20.5 89 According to Order
0.5 445 20.5 89 According to Order
www.unitech-ikk.comwww.unimetal-ikk.comwww.sfsp-ikk.com
ManamaTel : +973 17 874 897Fax: +973 17 789 [email protected]
DohaTel : +974 4451 3301/2/3Fax: +974 4451 [email protected]
Amman Tel : +962 6 556 3030Fax: +962 6 554 [email protected]
Dubai - Al Rashidiyah / UAETel : +971 4 2591 773Fax : +971 4 2591 [email protected]
BeirutTel : +961 1 858 277Fax: +961 1 858 [email protected]
Tripoli ShowroomTel : +961 6 443 909Fax: +961 6 443 [email protected]
Abu Dhabi - Musaffah / UAETel: +971 2 552 3393Fax: +971 2 552 [email protected]
Al Ain / UAETel : +971 3 761 9050Fax: +971 3 761 [email protected]
UNITED ARAB EMIRATES
LEBANON
BAHRAIN
KINGDAOM OF SAUDI ARABIA
QATAR
MuscatTel : +968 24 591 006Fax : +968 24 597 [email protected]
OMAN
Cairo - El Gomhoria St. Tel: +20 2 2787 2152Fax: +20 2 2593 [email protected]
EGYPT
Tripoli Tel: +218 21 717 0264Fax: +218 21 477 [email protected]
LIBYA
Kuwait CityTel : +965 2 4924 937Fax: +965 2 4924 [email protected]
KUWAIT
JORDAN
JeddahTel : +966 12 627 8222Fax: +966 12 627 [email protected]
Jeddah - Ghurab ShowroomTel : +966 12 667 2000Fax: +966 12 661 [email protected]
Mak kah, TaifTel : +966 12 541 1206Fax: +966 12 532 [email protected]
Riyadh - WestTel : +966 11 431 6271Fax: +966 11 431 [email protected]
Riyadh NorthTel : +966 11 415 5465Fax: +966 11 415 [email protected]
Riyadh SouthTel : +966 11 448 0112Fax: +966 11 447 [email protected]
Qassim / BuraidahTel : +966 16 382 3946Fax: +966 16 385 [email protected]
Qassim ShowroomTel : +966 16 385 2598Fax: +966 16 385 [email protected]
Hafr el BatinTel : +966 13 729 3644Fax: +966 13 729 [email protected]
HailTel : +966 16 543 3931Fax: +966 16 543 [email protected]
Skakah / QurayyatTel : +966 14 626 3904Fax: +966 14 626 [email protected]
Khamis MushaytTel : +966 17 237 5929Fax: +966 17 237 [email protected]
NajranTel : +966 17 546 3873Fax : +966 17 546 [email protected]
SharorahTel : +966 17 532 8153Fax: +966 17 532 [email protected]
TabukTel : +966 14 423 5203Fax: +966 14 423 [email protected]
Al -BahaTel : +966 17 237 5929Fax: +966 17 237 [email protected]
GizanTel : +966 17 321 6660Fax: +966 17 321 [email protected]
Al QunfudahTel : +966 17 7350 266Fax: +966 17 7350 [email protected]
Mad inahTel : +966 14 842 1095Fax: +966 14 842 [email protected]
Mad inah Showroom - UPF Tel : +966 14 834 6244Fax: +966 14 834 [email protected]
YanbuTel : +966 14 390 1499Fax: +966 14 322 [email protected]
DammamTel : +966 13 859 0097Fax: +966 13 857 [email protected]
Dammam / ShowroomTel : +966 13 834 9300Fax: +966 13 834 [email protected]
Hufuf Tel : +966 13 530 1474Fax: +966 13 530 [email protected]
JubailTel : +966 13 361 4390Fax: +966 13 362 [email protected]
Hufuf / ShowroomTel : +966 13 586 9732Fax: +966 13 530 [email protected]
DESIGN, LOGISTICS, MATERIALS, MEDIA, R&D
FACTORIES
UNITECH GERMANYGermany, StuttgartTel : +49 711 6868 7222 Fax: +49 711 6868 [email protected]
SFSP - KSASFSP / Kingdom of Saudi ArabiaSpecialized Factory for Steel Products - 3rd Industrial City / JeddahTel: +966 12 637 4482, Fax: +966 12 636 [email protected]
Specialized Factory for Steel Products - Khumra / JeddahTel : +966 12 635 6066 Fax: +966 12 635 5658 [email protected]
SFSP / UAESIGMA Factory for Steel Products - DIC (Dubai Industrial City)Tel : +971 4 429 7024 Fax: +971 4 429 [email protected]
SFSP / EGYPTSpecialized Factory for Steel Products Lot No. 235 A- 3rd industrial zone 2nd service road 6th of October City Giza Tel : +20 2 3820 6477Tel : +20 2 3820 6235 Fax: +20 2 3820 [email protected]
SFSP / LebanonSpecialized Factory for Steel Products / s.a.r.l Tanayel, BekaaTel: +961 8 514 290Fax: +961 8 514 [email protected]
Muldit-DLebanon, Multi-D Beirut Tel : +961 1 841 155Fax: +961 1 841 [email protected]
UNITECH CHINAChina, Yiwu - Zhejiang ProvinceTel : +86 579 8545 3180Fax: +86 579 8542 [email protected]
TOSLUAE, Jebel AliTel : +971 4 8181947/4304Tel : +971 4 8181 941Fax: +971 4 [email protected]
TOSLKSATel : +966 12 627 8275Fax: +966 12 627 [email protected]