DVD VIDEO PLAYER DVPDVP 520520 - Philips · DVD VIDEO PLAYER DVPDVP 520520 01-34 DVP520_EU101 1...

/00_8239 210 98882

DVD VIDEO PLAYER DVP 520DVP 520

01-34 DVP520_EU101 19/03/2004, 11:22 AM1

/00_8239 210 98882

Important notes for users in theU.K.

Mains plugThis apparatus is fitted with an approved 13Amp plug. To change a fuse in this type of plugproceed as follows:

1 Remove fuse cover and fuse.

2 Fix new fuse which should be a BS1362 5 Amp,A.S.T.A. or BSI approved type.

3 Refit the fuse cover.

If the fitted plug is not suitable for your jackoutlets, it should be cut off and an appropriateplug fitted in its place.If the mains plug contains a fuse, this shouldhave a value of 5 Amp. If a plug without a fuseis used, the fuse at the distribution boardshould not be greater than 5 Amp.

Note: The severed plug must be disposed toavoid a possible shock hazard should it beinserted into a 13 Amp jack elsewhere.

How to connect a plugThe wires in the mains lead are coloured withthe following code: blue = neutral (N),brown = live (L).

¶ As these colours may not correspond with thecolour markings identifying the terminals inyour plug, proceed as follows:– Connect the blue wire to the terminalmarked N or coloured black.– Connect the brown wire to the terminalmarked L or coloured red.– Do not connect either wire to the earthterminal in the plug, marked E (or e) orcoloured green (or green and yellow).

Before replacing the plug cover, make certainthat the cord grip is clamped over the sheathof the lead - not simply over the two wires.

Copyright in the U.K.Recording and playback of material mayrequire consent. See Copyright Act 1956 andThe Performer’s Protection Acts 1958 to 1972.

CAUTIONUse of controls or adjustments orperformance of procedures other thanherein may result in hazardousradiation exposure or other unsafeoperation.

VAROITUSMuiden kuin tässä esitettyjentoimintojen säädön tai asetustenmuutto saattaa altistaa vaarallisellesäteilylle tai muille vaarallisilletoiminnoille.

01-34 DVP520_EU101 19/03/2004, 11:22 AM2

/00_8239 210 98882

DKAdvarsel: Usynlig laserstråling vedåbning når sikkerhedsafbrydere er udeaf funktion. Undgå utsættelse forstråling.

Bemærk: Netafbryderen er sekundærtindkoblet og ofbryder ikke strømmenfra nettet. Den indbyggede netdel erderfor tilsluttet til lysnettet så længenetstikket sidder i stikkontakten.

SKlass 1 laseraparatVarning! Om apparaten används påannat sätt än i denna bruksanvisningspecificerats, kan användaren utsättasför osynlig laserstrålning, somöverskrider gränsen för laserklass 1.

Observera! Stömbrytaren är sekundärtkopplad och bryter inte strömmen frånnätet. Den inbyggda nätdelen ärdärför ansluten till elnätet så längestickproppen sitter i vägguttaget.

SFLuokan 1 laserlaiteVaroitus! Laitteen käyttäminen muullakuin tässä käyttöohjeessa mainitullatavalla saattaa altistaa käyttäjänturvallisuusluokan 1 ylittävällenäkymättömälle lasersäteilylle.Oikeus muutoksiin varataan. Laite eisaa olla alttiina tippu-ja roiskevedelle.

Huom. Toiminnanvalitsin on kytkettytoisiopuolelle, eikä se kytke laitetta irtisähköverkosta. Sisäänrakennettuverkko-osa on kytkettynäsähköverkkoon aina silloin, kun pistokeon pistorasiassa.

01-34 DVP520_EU101 19/03/2004, 11:22 AM3

/00_8239 210 98882

General Information

CAUTION(WARNING LOCATION: ON THEBACKPLATE OF THE SET)

NEVER MAKE OR CHANGECONNECTIONS WITH THEPOWER SWITCHED ON.

The DVD VIDEO player is inconformity with the EMC directiveand low-voltage directive.

Manufactured under license from DolbyLaboratories. “Dolby”, “Pro Logic” and thedouble-D symbol are trademarks of DolbyLaboratories.

Laser safety

This unit employs a laser. Due to possibleeye injury, only a qualified service personshould remove the cover or attempt toservice this device.

NOTE:PICTURES SHOWN MAYBEDIFFERENT BETWEENCOUNTRIES.

LASERType Semiconductor laser

GaAlAsWave length 650 nm (DVD)

780 nm (VCD/CD)Output Power 7 mW (DVD)

10 mW (VCD/CD)Beam divergence 60 degree

For Customer Use:

Read carefully the information located atthe bottom of your DVD VIDEO playerand enter below the Serial No. Retain thisinformation for future reference.

Model No. DVP520Serial No. _______________

Environmental InformationAll unnecessary packaging has beenomitted. The packaging has been madeeasy to separate into three materials:cardboard (box), polystyrene foam(buffer) and polyethylene (bags, protectivefoam sheet).

Your DVD player consists of materialswhich can be recycled and reused ifdisassembled by a specialised company.Please observe the local regulationsregarding the disposal of packagingmaterials, exhausted batteries and oldequipment.

Important Note:Due to the numerous versions of newCD-Audio copy protection orenhanced CD-Audio protectionrecently available on certain discs,Philips is unable to guarantee thatthis DVD Player is fully compatiblewith such new discs. Should you havedifficulty playing any such CD-Audiodiscs, kindly refer them to your CD-Audio disc retailer.

The apparatus shall not be exposed to drippingor splashing and that no objects filled withliquids, such as vases, shall be placed onapparatus.

01-34 DVP520_EU101 19/03/2004, 11:22 AM4

/00_8239 210 98882

En

gli

s hF

ran

ça

isD

eu

t sc

hN

ed

er l

an

ds

5

Index

CAUTIONVISIBLE AND INVISIBLE LASERRADIATION WHEN OPEN.AVOID EXPOSURE TO BEAM.ADVARSELSYNLIG OG USYNLIGLASERSTRÅLING VED ÅBNINGUNDGÅ UDSÆTTELSE FOR STRÅLINGVARNINGSYNLIG OCH OSYNLIGLASERSTRÅLNING NÄR DENNA DELÄR ÖPPNAD BETRAKTA EJ STRÅLENVARO!AVATTAESSA OLET ALTTIINANÄKYVÄLLE JA NÄKYMÄTTÖMÄLLELASER SÄTEILYLLE. ÄLÄ KATSOSÄTEESEENVORSICHTGEFAHR VON SICHTBARER UNDUNSICHTBARER LASERSTRAHLUNGBEI GEÖFFNETEM GEHÄUSE.ATTENTIONRAYONNEMENT LASER VISIBLE ETINVISIBLE EN CAS D’OUVERTUREEXPOSITION DANGEREUSE AUFAISCEAU

English --------------------------------------- 6

Français ------------------------------------ 35

Deutsch ------------------------------------ 63

Nederlands ------------------------------- 91

01-34 DVP520_EU101 19/03/2004, 11:22 AM5

/00_8239 210 98882

En

glish

6

IntroductionSupplied accessories ....................................... 7Care and safety information .......................... 7

ConnectionsConnecting TV .............................................. 8-9

Using SCART jack ........................................... 8Using Composite Video jacks (CVBS) ........ 8Using S-Video jack .......................................... 9Using an accessory RF modulator .............. 9

Connecting the power cord ........................ 10Optional : Connecting to an Audio System ............................................................................ 11

Stereo system has Dolby Pro Logic or Right/ Left Audio In jack ....................................... 11

Optional: Connecting Digital AV Receiver .............................................................................. 11

Receiver has a PCM, Dolby Digital, orMPEG2 decoder ............................................ 11

Functional OverviewFront and Rear Panels .................................. 12Remote Control ............................................ 13

Getting StartedStep 1: Inserting batteries into theRemote Control ............................................ 14

Using the Remote Control to operate thePlayer ............................................................... 14

Step 2: Setting up the TV .............................. 14Selecting the colour system thatcorresponds to your TV .............................. 15

Step 3: Setting language preference ........... 16Setting the OSD Language .......................... 16Setting the Audio, Subtitle and Disc menulanguage .......................................................... 16

Disc OperationsPlayable Discs ................................................. 17Playing discs ..................................................... 17Using the Disc Menu ..................................... 18Basic playback controls ........................... 18-20

Pausing playback ............................................ 18Selecting track/chapter ................................ 18Resuming playback from the last stoppedpoint ................................................................ 18Zoom .............................................................. 19Repeat ............................................................. 19Repeat A-B ..................................................... 19Slow Motion .................................................. 19Forward / Reverse Searching ..................... 19Time Search ................................................... 20

Special DVD features .................................... 20Playing a Title ................................................. 20Camera Angle ................................................ 20Changing the Audio Language .................... 20Subtitles .......................................................... 20

Special VCD & SVCD Features ................... 21Preview ........................................................... 21

Playing MP3/JPEG Picture CD ..................... 21General Operation ....................................... 21Playback selection ......................................... 21Repeat (MP3/JPEG) ...................................... 21Program playback ......................................... 21Fast Forward/Reverse .................................. 21

Special MP3/JPEG features ........................... 22Preview Function (JPEG) ............................. 21Zoom picture (JPEG) ................................... 21Playback with multi-angles (JPEG) ............. 21

System Menu OptionsBasic Operations ........................................... 23General Setup Page ....................................... 23

Program .......................................................... 23Screen Saver .................................................. 23

Audio Setup Page ..................................... 24-26Speaker Setup ................................................ 24Digital Audio Setup ................................ 24-25Dolby Digital Setup ...................................... 25Equalizer ......................................................... 263D Processing ................................................ 26

Video Setup Page ..................................... 27-28TV Display ...................................................... 27Closed Captions ........................................... 27Angle Mark ..................................................... 28Smart Picture ................................................. 28Picture Setting ............................................... 28

Preference Setup Page ............................ 29-30Parental ........................................................... 29Password ........................................................ 30Default ............................................................. 30

Specifications ...................................... 31

Troubleshooting ......................... 32–33

Glossary ......................................................................34

Contents

01-34 DVP520_EU101 19/03/2004, 11:22 AM6

/00_8239 210 98882

En

gli

s h

7

Supplied accessories

Remote Controlandtwo AA batteries

Introduction

Care and safety information● Power consumption

– When the system is switched toStandby mode, it is still consuming power.To disconnect the system from the powersupply completely, remove the AC powerplug from the wall jack.

● Avoid high temperatures, moisture,water and dust– Do not expose the player, batteries ordiscs to humidity, rain, sand or excessiveheat (caused by heating equipment ordirect sunlight.)

● Avoid condensation problem– The lens may cloud over when theplayer is suddenly moved from cold towarm surroundings, making it impossibleto play a disc. Leave the player in thewarm environment until the moistureevaporates.

PREVIEWPREVIEW MUTEMUTE

● Do not block the vents– Do not operate the DVD Player in anenclosed cabinet, allow about 10 cm (4inches) of free space all around the playerfor adequate ventilation.

10 cm(4 inches)

10 cm(4 inches)

10 cm(4 inches)DVD Home Cinema System

PHILIPS

● Care of the cabinet– Use a soft cloth slightly moistened witha mild detergent solution. Do not use asolution containing alcohol, spirits,ammonia or abrasives.

● Finding a suitable location– Place the player on a flat, hard, andstable surface.

● Disc handling– To clean a CD, wipe it in astraight line from the centertowards the edge using a soft,lint-free cloth. A cleaningagent may damage the disc!– Write only on the printedside of a CDR(W) and only with a soft felt-tipped pen.– Handle the disc by its edge, do nottouch the surface.

01-34 DVP520_EU101 19/03/2004, 11:22 AM7

/00_8239 210 98882

En

glish

8

Connections

Connecting TV

LVIDEO OUT

S-VIDEO OUT

COAXIAL

TV OUT

MAINS

R

DIGITAL OUT AUDIO OUT

AUDIO IN

S-VIDEOIN

VIDEO IN

TV IN

AUDIO IN

S-VIDEOIN

VIDEO IN

TV IN

1

IMPORTANT!– You only need to make one videoconnection from the followingoptions, depending on thecapabilities of your TV system.– Connect the DVD system directlyto the TV.– SCART connection will let youuse the features of both the Audioand Video in the DVD Player.

Using SCART jack

● Use the SCART cable (black) to connectthe DVD Player’s SCART jack (TV OUT)to the corresponding Scart input jacks onthe TV (cable not supplied).

Helpful Hint:– Ensure that the “TV” indication onSCART cable is connected to the TVset and “DVD” indication on SCARTcable is connected to the DVD Player.

LVIDEO OUT

S-VIDEO OUT

COAXIAL

TV OUT

R


AUDIO IN

S-VIDEOIN

VIDEO IN

TV IN

AUDIO IN

S-VIDEOIN

VIDEO IN

TV IN

21

Using Composite Video jacks(CVBS)

1 Use the composite video cable (yellow) toconnect the DVD Player’s CVBS (VIDEOOUT) jack to the video input jack (orlabeled as A/V In, Video In, Composite orBaseband) on the TV (cable not supplied).

2 To hear the sound of this DVD Playerthrough your TV, use the audio cables(white/red) to connect AUDIO OUT (L/R) jacks of the DVD Player to thecorresponding AUDIO IN jacks on the TV(cable not supplied).

01-34 DVP520_EU101 19/03/2004, 11:22 AM8

/00_8239 210 98882

En

gli

s h

9

Connections

LVIDEO OUT

S-VIDEO OUT

COAXIAL

TV OUT

RDIGITAL OUT AUDIO OUT

AUDIO IN

S-VIDEOIN

VIDEO IN

TV IN

AUDIO IN

S-VIDEOIN

VIDEO IN

TV IN

21

IMPORTANT!– S-Video connection providesbetter picture quality. This optionmust be available on your TV.

Using S-Video jack

1 Use the S-video cable to connect theDVD system’s S-VIDEO OUT jack tothe S-Video input jack (or labeled as Y/Cor S-VHS) on the TV (cable not supplied).

2 To hear the sound of this DVD Playerthrough your TV, use the audio cables(white/red) to connect AUDIO OUT (L/R) jacks of the DVD Player to thecorresponding AUDIO IN jacks on the TV(cable not supplied).

IMPORTANT!– If your TV only has a singleAntenna In jack (or labeled as 75ohm or RF In,) you will need an RFmodulator in order to view the DVDplayback on the TV. See yourelectronics retailer or contactPhilips for details on RF modulatoravailability and operations.

Using an accessory RF modulator

1 Use the composite video cable (yellow) toconnect the DVD Player’s CVBS (VIDEOOUT) jack to the video input jack on theRF modulator.

2 Use the RF coaxial cable (not supplied) toconnect the RF modulator to your TV’sRF jack.

LVIDEO OUT

S-VIDEO OUT

COAXIAL

TV OUT

R


AUDIO IN

R LVIDEO

INTO TVANT IN

CH3 CH4

2

1

RF coaxial cable to TV

Back of RF Modulator(example only)

Antenna orCable TV signal

01-34 DVP520_EU101 19/03/2004, 11:22 AM9

/00_8239 210 98882

En

glish

10

Connections

LVIDEO OUT

S-VIDEO OUT

COAXIALMAINS

R


~ AC MAINS

AUDIO IN

V (Pr/Cr)

U (Pb/Cb)

Y

S-VIDEOIN

VIDEO IN

COMPONENTVIDEO IN

After everything is connectedproperly, plug in the AC power cordto the power outlet.Never make or change any connectionswith the power switched on.

When no disc is loaded, pressSTANDBY ON on the DVD Playerfront panel,“NO DISC” may appear on thedisplay panel.

EN/CLOSE STOP PLAY/PAUSE

Connecting the power cord

NO DISC

01-34 DVP520_EU101 19/03/2004, 11:22 AM10

/00_8239 210 98882

En

gli

s h

11

Stereo system has Dolby Pro Logicor Right / Left Audio In jack

1 Select one of the video connections(VIDEO IN, S-VIDEO IN or SCART jack(TV IN) depending on the optionsavailable on your TV.

2 Use the audio cables (white/red) toconnect AUDIO OUT (L/R) jacks ofthe DVD Player to the correspondingAUDIO IN jacks on the stereo system(cable not supplied).

Connections

LVIDEO OUT

S-VIDEO OUT

COAXIAL

TV OUT

R


AUDIO IN

STEREO

DIGITAL

OPTICAL

Optional: Connecting to anAudio System

Optional: Connecting Digital AVReceiver

LVIDEO OUT

S-VIDEO OUT

COAXIAL

TV OUT

MAINS

R


AUDIO IN

COAXIAL

AV Receiver

Receiver has a PCM, Dolby Digital,or MPEG2 decoder

1 Select one of the video connectionsVIDEO IN, S-VIDEO IN or SCART jack(TV IN) depending on the optionsavailable on your TV.

2 Connect the COAXIAL jack of the DVDPlayer to the corresponding Digital AudioIn jack on your Receiver (cable notsupplied).

3 Set the DVD Player’s Digital Output toPCM-ONLY or ALL depending on thecapabilities of your Receiver (see page 24“Digital Output”).

Helpful Hint:– If the audio format of the Digital Outputdoes not match the capabilities of yourreceiver, the receiver will produce a strong,distorted sound or no sound at all.

01-34 DVP520_EU101 19/03/2004, 11:22 AM11

/00_8239 210 98882

En

glish

12

Functional Overview

Front and Rear Panels

TV OUT– Connect to SCART input of a TV

Audio Out (Left/Right)– Connect to AUDIO inputs of an amplifier,

receiver or stereo system

Digital Out (Coaxial)– Connect to coaxial AUDIO input of a

digital audio equipment

STANDBY-ON OPEN/CLOSE STOP PLAY/PAUSE

STANDBY-ON B– To switch the DVD Player to Standby

mode or ON

Disc tray

OPEN/CLOSE /– Open/Close the disc tray

2; PLAY/PAUSE– To start or interrupt playback

9 STOP– To stop playback

IR Sensor– Point the remote control towards this

sensor

Display– Shows the current status of the DVD

Player

LVIDEO OUT

S-VIDEO OUT

COAXIAL

TV OUT

MAINS

R


Mains (AC Power Cord)– Connect to a standard AC outlet

S-Video Out– Connect to S-Video input of a TV

Video Out (CVBS)– Connect to CVBS Video input of a TV

Caution: Do not touch the inner pins of the jacks on the rear panel.Electrostatic discharge may cause permanent damage to the unit.

01-34 DVP520_EU101 19/03/2004, 11:22 AM12

/00_8239 210 98882

En

gli

s h

13

Functional Overview

Remote Control

PREVIEW MUTEMUTE

RETURN / TITLE– To go back to previous menu /

show title menu

DISC MENU– Enters or exits the disc contents

menu– Switches on or off the playback

control mode (for VCD version2.0 only)

1 2 3 4– Selects an item in the menu/

fast backward/forward, slow forward/backward

OK– Acknowledge menu selection

S– To search or select previous

chapter or track

STOP ( 9 )– To stop playback

PLAY ( B )– To start playback

PAUSE ( ; )– To pause playback temporarily /

frame-by-frame playback

REPEAT– Selects various repeat modes

REPEAT (A-B)– Repeats playback a specific section

on a disc

PREVIEW– To preview the content of a track

or whole disc

MUTE– Disables or enables sound output

POWER B– To switch the DVD player to

standby mode or ON

0-9 numerical key pad– Selects numbered items in a

menu

DISPLAY– Displays information on TV

screen during playback

SYSTEM MENU– Access or exit DVD Player’s

system menu

T– To search or select next chapter

or track

SUBTITLE– To access subtitle language in disc

menu

ANGLE– Selects a DVD camera angle

ZOOM– Enlarge or reduce a picture on

the TV screen

AUDIO– To access audio language in disc

menu

01-34 DVP520_EU101 19/03/2004, 11:22 AM13

/00_8239 210 98882

En

glish

14

STOP

PREVIEWPREVIEW MUTEMUTE

Getting Started

Step 1: Inserting batteries intothe Remote Control

1

3

2

1 Open the battery compartment.

2 Insert two batteries type R06 or AA,following the indications (+-) insidethe compartment.

3 Close the cover.

Using the Remote Control tooperate the Player

1 Aim the Remote Controldirectly at the remotesensor (IR) on the frontpanel.

2 Do not put any objectsbetween the RemoteControl and the DVDPlayer while operating theDVD Player.

CAUTION!– Remove batteries if they areexhausted or if the Remote Controlis not being used for a long time.– Do not use old and new ordifferent types of batteries incombination.– Batteries contain chemicalsubstances, so they should bedisposed properly.

Step 2: Setting up the TV

IMPORTANT!Make sure you have completed allthe necessary connections. (Seepages 8-9 “Connecting TV”).

1 Turn on the TV and set to the correctvideo-in channel. You should see the bluePhilips DVD background screen on theTV.

➜ Usually these channels are between thelowest and highest channels and may becalled FRONT, A/V IN, or VIDEO. See yourTV manual for more details.➜ Or, you may go to channel 1 on yourTV, then press the Channel down buttonrepeatedly until you see the Video Inchannel.➜ Or, the TV Remote Control may have abutton or switch that chooses differentvideo modes.➜ Or, set the TV to channel 3 or 4 if youare using an RF modulator.

2 If you are using external equipment, (eg.audio system or receiver), turn it on andselect the appropriate input source forthe DVD Player output. Refer to theequipment owner’s manual for detail.

01-34 DVP520_EU101 19/03/2004, 11:22 AM14

/00_8239 210 98882

En

gli

s h

15

Getting Started

1 Press SYSTEM MENU.

2 Press 1 2 to select ‘Video Setup Page’.

3 Use the 1 2 3 4 keys on the RemoteControl to navigate in the menu.

Move to ‘TV Type’ and press 2.

PAL – Select this if the connected TV isPAL system. It will change the video signalof a NTSC disc and output in PAL format.

NTSC – Select this if the connected TVis NTSC system. It will change the videosignal of a PAL disc and output in NTSCformat.

Multi – Select this if the connected TV iscompatible with both NTSC and PAL(multi-system). The output format will bein accordance with the video signal of thedisc.

4 Select an item and press OK.

Selecting the colour system thatcorresponds to your TV

This DVD Player is compatible with bothNTSC and PAL. In order for a DVD discto play on this Player, the colour system ofthe Disc, the TV and the DVD Playershould match.

- - Video Setup Page - -

Set TV Standard

TV Type PALTV Display NTSCClosed Captions MultiAngle Mark Smart PicturePicture Setting

Helpful Hint:– Before changing the current TVType setting, ensure that your TVsupports the ‘selected TV Type’ system.– Follow the instructions thatappears on the TV screen.– If there is no proper picture onyour TV, wait for 15 seconds for autorecovery.

HINTS:(refer to the owner's manualChanging to (selected TV Type)1. Ensure your TV supports it.2. If there is a blank screen on normal TV, wait 15 seconds for auto recover

< > - Move OK - Select

CancelOK

Confirm again to use (selected TV Type)If picture is good press OK on remote

TO GO BACK TO (Current TV Type):1. Open tray2. Press '3' Key< > - Move OK - Select

CancelOK

To exit from the menuPress SYSTEM MENU or select ‘ExitSetup Menu’ and then press OK.

01-34 DVP520_EU101 19/03/2004, 11:22 AM15

/00_8239 210 98882

En

glish

16

Step 3: Setting languagepreferenceYou can select your own preferredlanguage settings.This DVD system willautomatically switch to the selectedlanguage whenever you load a disc. If thelanguage selected is not available on thedisc, the disc’s default language will beused instead. The OSD language in thesystem menu will remain once selected.

Setting the OSD Language

- - General Setup Page - -

Set OSD Language English

Program ENGLISH OSD Language DEUTSCHScreen Saver NEDERLANDS FRANÇAIS ITALIANO ESPANOL SVENSKA PORTUGUESE


2 Press 1 2 to select ‘General Setup’ page.

3 Use the 1 2 3 4 keys on the RemoteControl to navigate in the menu.

Move to ‘OSD Language’ and press 2.

4 Select a language and press OK.


Setting the Audio, Subtitle and Discmenu language

- - Preference Page - -

Set Preference To English

Audio EnglishSubtitle ChineseDisc Menu JapaneseParental FrenchPassword GermanDefault Spanish Dutch Italian

1 Press STOP twice then, press SYSTEMMENU.

2 Press 1 2 to select ‘Preference Page’.

3 Press 3 4 to highlight the following in thePreference Page.– ‘Audio’ (disc’s soundtrack)– ‘Subtitle’ (disc’s subtitles)– ‘Disc Menu’ (disc’s menu)

4 Enter its submenu by pressing B.

5 Select a language and press OK.

6 Repeat steps 3~5 for other languagesettings.


If you choose OTHERS in Audio,Subtitle or Disc Menu,

1 Press 3 4 to highlight ‘Others’.

2 Press OK and when you are asked toenter a language code (see ‘LanguageCode’ on page 119).

3 Input a language code by using thenumeric keypad (0-9).

4 Press OK to confirm.

Getting Started

01-34 DVP520_EU101 19/03/2004, 11:22 AM16

/00_8239 210 98882

En

gli

s h

17

Disc Operations

IMPORTANT!– Depending on the DVD or VIDEOCD, some operations may bedifferent or restricted.– Do not push on the disc tray orput any objects other than disc onthe disc tray. Doing so may causethe disc player malfunction.

Playable Discs

Your DVD Player will play:– Digital Versatile Discs (DVDs)– Video CDs (VCDs)– Super Video CDs (SVCDs)– Digital Versatile Discs + Recordable

(DVD+R)– Digital Versatile Discs + Rewritable

(DVD+RW)– Compact Discs (CDs)– MP3 disc on CD-R(W):

–Maximum 30 characters display.–Supported sampling frequencies :

32 kHz, 44.1 kHz, 48 kHz–Supported Bit-rates : 32~256 kbps

variable bitrates– Picture (JPEG) files on CD-R(W):

– JPEG/ISO 9660 format.

Region CodesDVDs must be labelled for ALLregions or Region 2 in order toplay on this DVD system. Youcannot play discs that are labelledfor other regions.

Helpful Hint:– If you are having trouble playing acertain disc, remove the disc and try adifferent one. Improper formatted disc willnot play on this DVD Player.

ALL

2

IMPORTANT!If the inhibit icon (ø) appears on theTV screen when a button is pressed,it means the function is not availableon the current disc or at the currenttime.

Playing discs

1 Connect the power cords of the DVDPlayer and TV (and any optional stereo orAV receiver) to a power outlet.

2 Turn on the TV power and set to thecorrect Video In channel. (See page 14“Setting up the TV”).

3 Press STANDBY-ON on the DVD Playerfront panel.➜ You should see the blue Philips DVDbackground screen on the TV.

4 Press OPEN•CLOSE 0 button to openthe disc tray and load in a disc, then pressthe same button again to close the disctray.➜ Make sure the label side is facing up.For double-sided discs, load the side youwant to play facing up.

5 Playback will start automatically(depending on the disc type).➜ If a disc menu appears on the TV, see“Using the Disc Menu”.➜ If the disc is locked by parental control,you must enter your four-digit password.(See page 30).

6 At any time, simply press STOP to stopplayback.

01-34 DVP520_EU101 19/03/2004, 11:22 AM17

/00_8239 210 98882

En

glish

18

Disc Operations

Using the Disc MenuDepending on the disc, a menu mayappear on the TV screen once you loadthe disc.

To select a playback feature or item● Use the 1 2 3 4 or numeric keypad

(0-9) on the Remote Control, then pressPLAY B to start playback.

To access or exit from the menu● Press DISC MENU on the Remote

Control.

For VCD with Playback Control(PBC) feature (version 2.0 only)

PBC playback allows you to play VideoCDs interactively, following the menu onthe display.

● In stop mode, use the numeric keypad(0-9) to select a track and PBC will turnoff.➜ Playback will start automatically

● During playback, press DISC MENU;➜ If PBC was ON, it will switch to OFFand continue playback.➜ If PBC was OFF, it will switch to ONand return to menu screen.

● During playback, pressing RETURN/TITLE will return to the menu screen (ifPBC is on).

Basic playback controlsUnless otherwise stated, all operationsdescribed are based on the use ofRemote Control.

Pausing playback(DVD/VCD/CD/MP3)

1 During playback, press PAUSE ;.➜ Playback will pause and sound will bemuted.

2 Press PAUSE ; again to select the nextpicture frame.

3 To return to normal playback, pressPLAY B.

Selecting track/chapter(DVD/VCD/CD)

1 Press T briefly during playback to goto the next chapter/track

2 Press S to go to the previous track(VCD/CD) or return to the beginning ofthe current chapter (DVD).

● Press S twice briefly to step back tothe previous chapter (DVD).

3 To go directly to any chapter/track, enterthe chapter/track number using thenumerical keys (0-9).

Resuming playback from the laststopped point (DVD/VCD/CD/MP3)

● In stop mode and when the disc has notbeen ejected, press PLAY B.

To cancel resume mode● In stop mode, press STOP 9 again.

01-34 DVP520_EU101 19/03/2004, 11:22 AM18

/00_8239 210 98882

En

gli

s h

19

Disc Operations

Repeat (DVD/VCD/CD)

● Press REPEAT continuously to choose aRepeat mode during playback.

REPEAT CHAPTER (DVD)– to repeat playback of the currentchapter.

REPEAT TRACK/TITLE (CD/VCD/DVD)– to repeat playback of the currenttrack (CD/SVCD/VCD)/title (DVD).

REPEAT ALL– to repeat playback of all the disc andall the programmed tracks.

SHUFFLE– to repeat playback at random order.

REPEAT OFF– to cancel the repeat mode.

Helpful Hint:– REPEAT function is not available for VCD2.0 when PCB is on.

Repeat A-B (DVD/VCD/CD)

1 Press REPEAT A-B at your chosenstarting point.

2 Press REPEAT A-B again at your chosenend point.➜ The section A and B can be set onlywithin the same chapter/track.➜ The section will now repeat continuously.

3 To exit the sequence, press REPEAT A-B.

Zoom (DVD/VCD/JPEG)

Zooming allows you to enlarge or reducethe video image during playback.

1 Press ZOOM repeatedly to increase anddecrease the playback video image.

2 Press 1 2 3 4 to pan across the TVscreen.

Forward / Reverse Searching(DVD/VCD/CD)

1 Press 1 2 during playback to select therequired speed: 2X, 4X, 8X, 16X or 32X(backward or forward).➜ Sound will be muted (DVD/VCD) orintermittent (CD).

2 To return to normal speed, press PLAY B.

Slow Motion (DVD/VCD)

1 Press 3 4 during playback to select therequired speed: 1/2, 1/4, 1/8 or 1/16(backward or forward).➜ Sound will be muted.

2 To return to normal speed, press PLAY B.

Helpful Hint:– Slow backward is not possible on VCDs.

01-34 DVP520_EU101 19/03/2004, 11:22 AM19

/00_8239 210 98882

En

glish

20

Time Search (DVD/VCD)

The Time Search function allows you tostart playing at any chosen time on thedisc.

1 Press DISPLAY.

2 Press 3 4 to highlight time search box.➜ The on-screen display shows the totalplaying time of the title/chapter.

Bitrate 67 TT Elapsed 0:16:35Bitrate 67 TT Elapsed 0:16:35

TT Time TT Time 0:03:010:03:01CH Time CH Time 0:01:080:01:08Repeat Repeat OffOffTime Disp. Time Disp. TT ElapsedTT Elapsed

MenuMenu

3 Use 2 keys to select an option.

4 Enter hours, minutes and seconds fromleft to right in the time edit box usingremote control numerical key pad.(e.g. 0:34:27)

For DVD➜ Title/Chapter Remain: displays theremaining time of the current title/chapter.➜ Title/Chapter Elapsed: displays theelapsed time of the current title/chapter.

For Super VCD or VCD➜ Total/Single Remain: displays theremaining time of the current total/singletrack.➜ Total/Single Elapsed: displays theelapsed time of the current total/singletrack.

5 Press the DISPLAY key to confirm.➜ Playback starts from the selected timeon the disc.

Disc Operations

Special disc features

Playing a Title (DVD)

1 Press DISC MENU.➜ The disc title menu appears on the TVscreen.

2 Use 341 2 keys or numeric keypad(0-9) to select a play option.

3 Press OK key to confirm.

Camera Angle (DVD)

● Press ANGLE repeatedly to selectdifferent desired angle.

Changing the Audio Language(DVD/VCD)

For DVD● Press AUDIO repeatedly to select

different audio languages.

Changing the Audio Channel

For VCD● Press AUDIO to select the available

audio channels provided by the disc(STEREO, MONO LEFT, MONO RIGHTor MIX MONO).

Subtitles (DVD)

● Press SUBTITLE repeatedly to selectdifferent subtitle languages.

01-34 DVP520_EU101 19/03/2004, 11:22 AM20

/00_8239 210 98882

En

gli

s h

21

Disc Operations

Preview Function (DVD/VCD)

The preview function allows you toreduce the picture of 6 tracks enough todisplay in a full screen.

1 Press PREVIEW.➜ The preview menu appears on the TVscreen.

Select Digest Type:Title DigestChapter DigestTitle IntervalChapter Interval

Select Digest Type:Title DigestChapter DigestTitle IntervalChapter Interval

Select Digest Type:Track DigestDisc IntervalTrack Interval

Select Digest Type:Track DigestDisc IntervalTrack Interval

2 Press 3 4 to select the PREVIEW type,then press OK.➜ The picture of each segment willappear on the screen.

A B C

D E F

(example for 6 thumbnail pictures display)

3 Press 3 4 1 2 to select a track and inputyour selected track number using thenumeric keypad (0-9), then press OK.➜ Playback will start automatically on theselected track.

● For CDDA (Musical CD)➜ Press PREVIEW to listen to the first10 seconds of each sound track in thedisc.

(DVD example) (Video CD example)

Playing MP3/JPEG Picture CD

IMPORTANT!You have to turn on your TV and set tothe correct Video In channel. (See page14 “Setting up the TV”).

General Operation

1 Load an MP3/JPEG Picture CD disc.➜ The data disc menu appears on the TVscreen.

2 Use 3 4 to select the folder and pressOK to open the folder.

00:37 03:50 128kbps001/162

\MP3\

Song 1

Song 2

Song 3

Song 4

Song 5

MP3

MP3

MP3

MP3

MP3

3 Press 3 4 or use the numeric keypad(0-9) to highlight an option.

4 Press OK to confirm.➜ The playback will start from theselected file to the end of the folder.

Playback selection

During playback, you can;

● Press S / T to select another file inthe current folder.

● Use 1 2 3 4 on the remote to rotate/flipthe picture files.

● Press ; repeatedly to pause/resumeplayback.

01-34 DVP520_EU101 19/03/2004, 11:23 AM21

/00_8239 210 98882

En

glish

22

Disc Operations

Program playback

● In Stop mode, press DISC MENUrepeatedly to toggle the menu betweenFolder and Filelist.

1 When Filelist is on the screen, press 3 4to select the files and press 2 to add thefiles to the playlist.

2 Press DISC MENU to display the playlist.

3 Press 1 to delete unwanted files from theplaylist.

Helpful Hint:– The disc reading time may exceed 10seconds due to large number of songscompiled onto the disc.

Fast forward / reverse (MP3)

● During playback, press 1 2 to fast forwardor reverse playback.

● To resume normal playback, press PLAYB.

Repeat

● Press REPEAT continuously to accessdifferent ‘Play Mode’.➜ SINGLE: play the selected file once,then return to the menu.➜ REPEAT ONE: keep a JPEG image still onthe screen or play an MP3 file repeatedly.➜ REPEAT FOLDER: play all files in theselected folder repeatedly.➜ SHUFFLE: play all files in the selectedfolder in random order.➜ FOLDER : play all files in the selectedfolder.

Special JPEG features

Preview Function (JPEG)

This function shows the content of thecurrent folder or the whole disc.

1 Press PREVIEW during playback.➜ Thumbnails of 12 pictures appears onthe TV screen.

(example for 12 thumbnail pictures display)

2 Press S / T to display the otherpictures on the previous/next page.

3 Use 1 2 3 4 to highlight one of thepicture and press OK to start playback,

4 Press DISC MENU to return to MP3/Picture CD menu.

Zoom picture (JPEG)

● During playback, press ZOOM repeatedlyto display the picture with different scales.

● Use 1 2 3 4 to view the zoomed picture.

Playback with multi-angles (JPEG)

● During playback, press 3 4 1 2 to rotatethe picture on the TV screen.3: flip the picture vertically4: flip the picture horizontally1: rotate the picture anti-clockwise2: rotate the picture clockwise

01-34 DVP520_EU101 19/03/2004, 11:23 AM22

/00_8239 210 98882

En

gli

s h

23

Basic Operations

1 Press SYSTEM MENU to enter theSetup Menu.

2 Press OK to enter the next levelsubmenu or confirm your selection.

3 Press 1 2 to enter the submenu orreturn to the previous menu.

4 Press 34 to highlight the desired menu.

To exit from the menuPress SYSTEM MENU or select ‘ExitSetup Menu’ and then press OK.➜ The settings will be stored in theplayer’s memory even if the player isswitched off.

General Setup Page

The options included in General Setuppage are: ‘Program’, ‘OSD Language’, and‘Screen Saver’.Follow the steps below:


Go To General Setup Page

Program OSD Language Screen Saver

1 Press SYSTEM MENU to enter thesetup menu.

2 Press 1 2 to select the ‘General Setup’page.

System Menu Options

NOTE:Some of the features in the SystemMenu Options are described in“Getting Started”.

Program (not for Picture CD/MP3)

To select favourite tracks/chaptersplayback in preferred sequence.

Program:Chapter(01-12)

START NEXTExit

1 122 01345

6789

10

05

1 Use the numerical keypad (0-9) todirect input the tracks or chapters (singletrack number with digit ‘0’ in front, forexample ‘05’).

2 Move the cursor by pressing 3 4 1 2 toselect START.

3 Press OK to start playback.

Helpful Hint:– Program can be activated only when adisc is in the DVD player.

Screen Saver

This function is used to turn the screensaver on or off.


Screen Saver

Program OSD Language Screen Saver On Off

1 Press 34 to highlight ‘Screen Saver’.

2 Enter its submenu by pressing 2.

3 Move the cursor by pressing 34 tohighlight the selected item.➜ On: In STOP, PAUSE or No DISCmode, if no actions are performed about5 minutes, the screen saver will beactivated.➜ Off: Screen saver is disabled.

01-34 DVP520_EU101 19/03/2004, 11:23 AM23

/00_8239 210 98882

En

glish

24

System Menu Options

Speaker Setup

The options included in Speaker Setupare: ‘Downmix’ and ‘D.R.C’.

1 Press the 34 keys to highlight an option.


3 Move the cursor by pressing the 34 keysto highlight the selected item.

- - Speaker Setup Page - -

Set Downmix Mode

Downmix LT/RTD.R.C Stereo Virtual Surround

DownmixThis options allows you to set the stereoanalog output of your DVD Player.➜ LT/RT: Select this option if your DVDPlayer is connected to a Dolby Pro Logicdecoder.➜ Stereo: Select this option when outputdelivers sound from only the two frontspeakers.➜ Virtual Surround: Allows the DVDplayer to use virtual surround soundeffects.

Digital Audio Setup

The options included in Digital AudioSetup are: ‘Digital Output’ and ‘LPCMOutput’.




- - Digital Audio Page - -

Setup SPDIF

Digital Output SPDIF OffLPCM Output All PCM Only

Digital OutputSet the Digital output according to youroptional audio equipment connection.➜ SPDIF Off: Turns off the SPDIFoutput.➜ All: If you have connected yourDIGITAL AUDIO OUT to a multi-channeldecoder/receiver.➜ PCM Only: Only if your receiver isnot capable of decoding multi-channelaudio.

Helpful Hint:– If DIGITAL OUTPUT is set to ‘All’, allaudio settings except MUTE are invalid.

Audio Setup PageThe options included in Audio Setup pageare: ‘Speaker Setup’, ‘Digital Audio Setup’,‘Dolby Digital Setup’, ‘Equalizer’ and ‘3D’.


2 Press 1 2 to select the ‘Audio Setup’ page.

D.R.C (Dynamic Range Control)

Analogue sound dynamic rangecompression.➜ On: Audio with fully compresseddynamic range.➜ Off: Audio with uncompressed dynamicrange.➜ Auto: Select ‘Auto’ to adjust thedynamic level automatically according tothe disc record.

01-34 DVP520_EU101 19/03/2004, 11:23 AM24

/00_8239 210 98882

En

gli

s h

25

LPCM Output

If you connect the DVD Player to a PCMcompatible receiver via the digitalterminals, such as coaxial or optical etc,you may need to adjust ‘LPCM Output’.Discs are recorded at a certain samplingrate. The higher the sampling rate, thebetter the sound quality.

➜ 48kHz: Playback a disc recorded at thesampling rate of 48kHz.➜ 96kHz: Playback a disc recorded at thesampling rate of 96kHz.

Helpful Hint:– LPCM Output can be selected only whenPCM Only is activated.

Dolby Digital Setup

The options included in Dolby DigitalSetup are: ‘Dual Mono’ and ‘Dynamic’.




- - Dolby Digital Setup - -

Dual Mono (1 + 1) Setup

Dual Mono StereoDynamic L-Mono R-Mono MIX-Mono

Dual MonoTo select the setting that matches thenumber of speakers you have connected.➜ Stereo: Left mono sound will sendoutput signals to Left speaker and Rightmono sound will send output signals toRight speaker.➜ L-Mono: Left mono sound will sendoutput signals to Left speaker and Rightspeaker.➜ R-Mono: Right mono sound will sendoutput signals to Left speaker and Rightspeaker.➜ Mix-Mono: Left and Right mixedmono sound will send output signals toLeft and Right speakers.

Dynamic

To optimise the dynamic sound outputhigh volume outputs are softened,enabling you to watch your favouritemovie without disturbing others.➜ The levels for dynamic selection:Full, 3/4, 1/2, 1/4 and Off.

Helpful Hint:– DTS surround audio output are notavailable in this DVD player.

System Menu Options

01-34 DVP520_EU101 19/03/2004, 11:23 AM25

/00_8239 210 98882

En

glish

26

System Menu Options

Equalizer

The option included in Equalizer is: ‘SoundMode’.

1 Press 34 to highlight ‘Sound Mode’.



- - Equalizer Page - -

None

Sound Mode None Rock Pop Live Dance Techno Classic Soft

Sound ModeSelect a Sound Mode that matches thetype of music you are playing. Thesepreset Sound Modes adjust the frequencybands of the audio to enhance yourfavourite music.➜ None, Rock, Pop, Live, Dance,Techno, Classic and Soft

3D Processing

The option included in 3D Processing is:‘Reverb Mode’.

1 Press 34 to highlight ‘Reverb Mode’.



- - 3D Processing Page - -

Reverb Mode

Reverb Mode Off Concert Living Room Hall Bathroom Cave Arena Church

Reverb ModeReverb mode provides a virtual surroundsound experience using just two speakers.➜ Off, Concert, Living Room, Hall,Bathroom, Cave, Arena and Church

Helpful Hint:– Reverb mode will be activated when‘Downmix’ is set to off.

01-34 DVP520_EU101 19/03/2004, 11:23 AM26

/00_8239 210 98882

En

gli

s h

27

Video Setup PageThe options included in Video Setup pageare: ‘TV Type’, ‘TV Display’, ‘ClosedCaptions’, ‘Angle Mark’, ‘Smart Picture’,and ‘Picture Setting’.


2 Press 1 2 to select the ‘Video Setup’ page.

- - Video Setup Page - -

Go To Video Setup Page

TV Type TV DisplayClosed CaptionsAngle MarkSmart PicturePicture Setting

TV Display

Set the aspect ratio of the DVD Playeraccording to the TV you have connected.

1 Press 34 to highlight ‘TV Display’.


3 Move the cursor by pressing 34 tohighlight the selected item.

16:9

4:3Letter Box

4:3Pan Scan

System Menu Options

16:9➜ If you have a wide-screen TV.

4:3 Letter Box➜ If you have a normal TV. In this case, awide picture with black bands on theupper and lower portions of the TVscreen will be displayed.

4:3 Pan Scan➜ If you have a normal TV and want bothsides of the picture to be trimmed orformatted to fit your TV screen.

Closed Captions

Closed captions are data that are hiddenin the video signal of some discs. Captionsare different from subtitles becausecaptions hearing are impaired by showingthe sound effects (e.g., “phone ringing”and “footsteps”), while subtitles do not.Before you select this function, pleaseensure that the disc contains closedcaptions information and your TV set alsohas this function.

1 Press 34 to highlight ‘Closed Captions’.


3 Move the cursor by pressing 34 tohighlight the selected item.➜ On: Enable Closed Captions.➜ Off: Disable Closed Captions.

01-34 DVP520_EU101 19/03/2004, 11:23 AM27

/00_8239 210 98882

En

glish

28

System Menu Options

Angle Mark

Displays current angle setting informationon the right hand corner of the TV screenif available on the disc.

1 Press 34 to highlight ‘Angle Mark’.


3 Move the cursor by pressing 34 tohighlight the selected item.➜ On: Enable Angle Mark.➜ Off: Disable the current angle settingdisplay.

Smart Picture

In this menu, you can choose a picturesetting from a fixed set of predefinedpicture settings.

1 Press 34 to highlight ‘Smart Picture’.


3 Move the cursor by pressing 34 tohighlight the selected item.➜ Standard: select the standard picturesetting.➜ Bright: make the TV picture brighter.➜ Soft: make the TV picture softer.

Picture Setting

The options included in Picture SettingSetup page are: ‘Sharpness’, ‘Brightness’and ‘Contrast’.




- - Picture Setting Setup - -

Low

Sharpness HighBrightness 00 MediumContrast 00 Low

SharpnessYou can personalise your picture colourby adjusting sharpness, brightness orcontrast.➜ High: Choose high to make thepicture’s edge sharper.➜ Medium: Choose medium to get astandard picture.➜ Low: Choose low to make thepicture’s edge softer.

Brightness/ContrastChoose a positive value to increase thebrightness/contrast level or move to anegative value to decrease the brightness/contrast level.

01-34 DVP520_EU101 19/03/2004, 11:23 AM28

/00_8239 210 98882

En

gli

s h

29

System Menu Options

Preference Setup PageThe options included in Preference pageare: ‘Audio’, ‘Subtitle’, ‘Disc Menu’,‘Parental’, ‘Password’ and ‘Default’.


2 Press 1 2 to select the ‘Preference Page’.

- - Preference Page - -

Go To Preference Page

AudioSubtitleDisc MenuParentalPasswordDefault

Note:Preference features can be selectedonly during ‘No Disc’ condition orSTOP mode.

Parental

Some DVDs may have a parental levelassigned to the complete disc or tocertain scenes on the disc. This featurelets you set a playback limitation level.The rating levels are from 1 to 8 and arecountry dependent. You can prohibit theplaying of certain discs that are notsuitable for your children or have certaindiscs played with alternative scenes.

● VCD, SVCD, CD have no level indication,so parental control function has no effecton those kinds of discs. This applies tomost illegal DVD discs.

1 Press 34 to highlight ‘Parental’.


3 Use 34 to highlight a rating level for thedisc inserted.➜ DVDs that are rated above the levelyou selected will not play unless you enteryour four-digit password and choose ahigher level rating.➜ To disable Parental controls and haveall Discs play, choose ‘Off’.

Parental - cont’d

Helpful Hint:– Some DVDs are not encoded with arating though the movie rating may beprinted on the Disc cover. The rating levelfeature does not work for such Discs.

Rating explanations

1 KID SAFE– Kids material; recommended especially forchildren and viewers of all ages.

2 G– General Audience; recommended as acceptablefor viewers of all ages.

3 PG– Parental Guidance suggested.

4 PG13– Material is unsuitable for children under age 13.

5-6 PG-R– Parental Guidance - Restricted; recommendedthat parents restrict children under 17 fromviewing or allow to view only when supervised bya parent or adult guardian.

7 NC-17– No children under age 17; not recommendedviewing for children under age 17.

8 ADULT– Mature material; should be viewed only byadults due to graphic sexual material, violence orlanguage.

OFF– It will play all discs.

01-34 DVP520_EU101 19/03/2004, 11:23 AM29

/00_8239 210 98882

En

glish

30

System Menu Options

Password

This feature is used for Parental Control.Enter your four digit password when ahint is displayed on the screen. The defaultpassword is 1009.

1 Press 34 to highlight ‘Password’.


3 Press OK to open the ‘New Password’page.

Old Password

New Password

Confirm PWD

OK

4 Enter the existing 4 digit code.

5 Enter the new 4-digit code.

6 Enter the new 4-digit code a second timeto confirm.➜ The new 4 digit code will be take effect.

7 Press OK to exit.

Helpful Hints:– If the password has been changed, theparental and disc lock code will also bechanged.– The default password (1009) is alwaysactive even the password has been changed.

Default

Setting the ‘Default’ function will reset alloptions and your personal settings to thefactory defaults and all your personalsettings will be erased.

1 Press 34 to highlight ‘Default’.

2 Highlight RESET by pressing 2.

3 Press OK to confirm selection.

Caution!– When this function is activated, allsettings will be reset to factorydefaults.

01-34 DVP520_EU101 19/03/2004, 11:23 AM30

/00_8239 210 98882

En

gli

s h

31

TV STANDARD (PAL/50Hz) (NTSC/60Hz)Number of lines 625 525Playback Multistandard (PAL/NTSC)

VIDEO PERFORMANCEDA Converter 12 bit, 54mHzVideo Output 1Vpp — 75 ohmS-Video Output Y: 1Vpp — 75 ohm

C: 0.3 Vpp — 75 ohmRGB (SCART) output 0.7 Vpp — 75 ohm

AUDIO FORMATDigital Mpeg compressed Digital

Dolby Digital 16, 20, 24 bitsPCM fs, 44.1, 48, 96 kHz

MP3(ISO 9660) 96, 112, 128, 256 kbps& variable bit rate fs, 32,44.1, 48 kHz

Analog Sound StereoDolby Surround-compatible downmix from Dolby Digitalmulti-channel sound

Specifications

AUDIO PERFORMANCEDA Converter 24 bit, 192kHzDVD fs 96 kHz 4Hz- 44kHz

fs 48 kHz 4Hz- 22kHzSVCD fs 48 kHz 4Hz- 22kHz

fs 44.1kHz 4Hz- 20kHzCD/VCD fs 44.1kHz 4Hz- 20kHzSignal-Noise (1kHz) > 90 dBDynamic range(1kHz) > 80 dBCrosstalk (1kHz) > 80 dBDistortion/noise (1kHz) > 80 dBMPEG MP3 MPEG Audio L3

CONNECTIONSScart Output EuroconnectorS-Video Output Mini DIN, 4 pinsVideo Output Cinch (yellow)Audio Output(L+R) Cinch (white/red)Digital Output 1 coaxial

IEC60958 for CDDA / LPCMIEC61937 for MPEG 1/2,Dolby Digital

CABINETDimensions (w x h x d) 360 x 43 x 285 mmWeight Approximately 2.0 kg

POWER CONSUMPTIONPower inlet 220-230V; 50HzPower consumption 12WPower consumption in Standby mode < 1 W

Specifications subject to change without prior notice

01-34 DVP520_EU101 19/03/2004, 11:23 AM31

/00_8239 210 98882

En

glish

32

WARNINGUnder no circumstances should you try to repair the system yourself, as this willinvalidate the warranty. Do not open the system as there is a risk of electric shock.

If a fault occurs, first check the points listed below before taking the system for repair. Ifyou are unable to remedy a problem by following these hints, consult your dealer orPhilips for help.

Problem Solution

No power – Check if the AC power cord is properly connected.– Press the STANDBY ON on the front of the DVD

system to turn on the power.

No picture – Refer to your TV’s manual for correct Video Inchannel selection. Change the TV channel until yousee the DVD screen.

– Check if the TV is switched on.

Distorted picture – Sometimes a small amount of picture distortion mayappear depending on the disc being played back. Thisis not a malfunction.

Completely distorted picture or – Connect DVD Player directly to the TV.black/white picture with DVD – Make sure the disc is compatible with the DVD

Player.– Ensure that the DVD Player’s TV Type is set to match

that of the Disc and your TV.

No sound or distorted sound – Adjust the volume.– Ensure to select stereo output on your disc (except

multichannel).– Check that the speakers are connected correctly.– Ensure that the DTS disc also supports Dolby Digital

output.

No audio at digital output – Check the digital connections.– Check if your receiver can decode MPEG-2 or DTS

and if not, please make sure the digital output is setto PCM.

– Check if the audio format of the selected audiolanguage matches your receiver capabilities.

No sound and picture – Check that the SCART cable is connected to thecorrect device (See Connecting TV).

Disc can’t be played – The DVD+R/CD-R must be finalized.– Ensure the disc label is facing up.– Check if the disc is defective by trying another disc.– If you have recorded a Picture CD or MP3 CD

yourself, ensure that your disc contains at least 10pictures or 5 MP3 tracks.

– Region code incorrect.

Picture freezes momentarily – Check the disc for fingerprints/scratches andduring playback clean with a soft cloth wiping from centre to edge.

Troubleshooting

01-34 DVP520_EU101 19/03/2004, 11:23 AM32

/00_8239 210 98882

En

gli

s h

33

Problem Solution

No return to start-up screen when – Reset the unit by switching the player off, then ondisc is removed again.

The player does not respond to – Aim the Remote Control directly at the sensorthe Remote Control on the front of the player.

– Reduce the distance to the player.– Replace the batteries in the Remote Control.– Re-insert the batteries with their polarities (+/–

signs) as indicated.

Buttons do not work – To completely reset the player, unplug the ACcord from the AC outlet for 5-10 seconds.

Player does not respond to some – Operations may not be permitted by the disc.operating commands during playback. Refer to the instructions of the disc jacket.

DVD Player cannot read – Use a commonly available cleaning CD/DVD toCDs/DVDs clean the lens before sending the DVD Player for

repair.

Menu items cannot be selected – Press STOP twice before selecting System Menu.– Depending on the disc availability, some menu items

cannot be selected.

If you are unable to remedy a problem by following these hints, consult your dealeror service center (HOTLINE).

Troubleshooting

01-34 DVP520_EU101 19/03/2004, 11:23 AM33

/00_8239 210 98882

En

glish

34

Analog: Sound that has not been turned intonumbers. Analog sound varies, while digital sound hasspecific numerical values. These jacks send audiothrough two channels, the left and right.Aspect ratio: The ratio of vertical and horizontalsizes of a displayed image. The horizontal vs. verticalratio of conventional TVs. is 4:3, and that of wide-screens is 16:9.AUDIO OUT Jacks: Jacks on the back of the DVDSystem that send audio to another system (TV, Stereo,etc.).Bit Rate: The amount of data used to hold a givenlength of music; measured in kilobits per seconds, orkbps. Or, the speed at which you record. Generally,the higher the bit rate, or the higher the recordingspeed, the better the sound quality. However, higherbit rates use more space on a Disc.Chapter: Sections of a picture or a music piece on aDVD that are smaller than titles. A title is composedof several chapters. Each chapter is assigned a chapternumber enabling you to locate the chapter you want.Disc menu: A screen display prepared for allowingselection of images, sounds, subtitles, multi-angles, etcrecorded on a DVD.Digital: Sound that has been converted intonumerical values. Digital sound is available when youuse the DIGITAL AUDIO OUT COAXIAL orOPTICAL jacks. These jacks send audio throughmultiple channels, instead of just two channels asanalog does.Dolby Digital: A surround sound system developedby Dolby Laboratories containing up to six channelsof digital audio (front left and right, surround left andright, center and subwoofer).DTS: Digital Theater Systems. This is a surroundsound system, but it is different from Dolby Digital.The formats were developed by different companies.JPEG: A very common digital still picture format. Astill-picture data compression system proposed by theJoint Photographic Expert Group, which features smalldecrease in image quality in spite of its highcompression ratio.

MP3: A file format with a sound data compressionsystem. “MP3” is the abbreviation of Motion PictureExperts Group 1 (or MPEG-1) Audio Layer 3. By usingMP3 format. one CD-R or CD-RW can contain about10 times as much data volume as a regular CD can.Multichannel: DVD is specified to have each soundtrack constitute one sound field. Multichannel refersto a structure of sound tracks having three or morechannels.Parental Control: A function of the DVD to limitplayback of the disc by the age of the users accordingto the limitation level in each country. The limitationvaries from disc to disc; when it is activated, playbackwill be prohibited if the software’s level is higher thanthe user-set level.PCM (Pulse Code Modulation): A system forconverting analog sound signal to digital signal forlater processing, with no data compression used inconversion.Playback control (PBC): Refers to the signalrecorded on video CDs or SVCDs for controllingreproduction. By using menu screens recorded on aVideo CD or SVCD that supports PBC, you can enjoyinteractive-type software as well as software having asearch function.Region code: A system for allowing discs to beplayed back only in the region designated beforehand.This unit will only play discs that have compatibleregion codes. You can find the region code of yourunit by looking on the product label. Some discs arecompatible with more than one region (or ALLregions).S-Video: Produces a clear picture by sendingseparate signals for the luminance and the color. Youcan use S-Video only if your TV has S- video In jack.Title: The longest section of a picture or musicfeature on DVD, music, etc., in video software, or theentire album in audio software. Each title is assigned atitle number enabling you to locate the title you want.VIDEO OUT jack: Jack on the back of the DVDSystem that sends video to a TV.

Glossary

01-34 DVP520_EU101 19/03/2004, 11:23 AM34

DVD VIDEO PLAYER DVPDVP 520520 - Philips · DVD VIDEO PLAYER DVPDVP 520520 01-34 DVP520_EU101 1...

Documents

Transcript of DVD VIDEO PLAYER DVPDVP 520520 - Philips · DVD VIDEO PLAYER DVPDVP 520520 01-34 DVP520_EU101 1...