Diffusion & photolithography process for electronic device manufacturing
-
Upload
arunkrai -
Category
Engineering
-
view
187 -
download
2
Transcript of Diffusion & photolithography process for electronic device manufacturing
![Page 1: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/1.jpg)
DIFFUSION & PHOTOLITHOGRAPHY PROCESS FOR ELECTRONIC DEVICE MANUFACTURING
Submitted by-
Arun Kumar Rai
B-tech (M.E.)
Contact No. +91-9654956242
G.L. Bajaj Institute Of Technology & Management
![Page 2: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/2.jpg)
DIFFUSION
A uniformly doped ingot is sliced into wafers. An oxide film is then grown on the wafers. The film is patterned and etched using
photolithography exposing specific sections of the silicon.
The wafers are then spun with an opposite polarity doping source adhering only to the exposed areas.
The wafers are then heated in a furnace (800-1250 ◦c) to drive the doping atoms into the silicon.
![Page 3: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/3.jpg)
DIFFUSION PROCESS
![Page 4: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/4.jpg)
DIFFUSION CONTINUED
Diffusion is a cheaper and more simplistic method, but can only be performed from the surface of the wafers. Dopants also diffuse unevenly, and interact with each other altering the diffusion rate.
![Page 5: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/5.jpg)
PHOTOLITHOGRAPHY
Photolithography is a technique that is used to define the shape of micro-machined structures on a wafer.
![Page 6: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/6.jpg)
PHOTOLITHOGRAPHY PHOTORESISTThe first step in the photolithography process is to develop a mask, which will be typically be a chromium pattern on a glass plate. Next, the wafer is then coated with a polymer which is sensitive to ultraviolet light called a PHOTORESIST.Afterward, the PHOTORESIST is then developed which transfers the pattern on the mask to the PHOTORESIST layer.
![Page 7: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/7.jpg)
7
There are two basic types of Photo resist Positive and Negative.
Positive Resists:
Positive resists decomposes ultraviolet light. The resist is exposed with UV light wherever the underlying material is to be removed. In these resists, exposure to the UV light changes the chemical structure of the resist so that it becomes more soluble in the developer. The exposed resist is then washed away by the developer solution, leaving windows of the bare underlying material. The mask, therefore, contains an exact copy of the pattern which is to remain on the wafer.
![Page 8: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/8.jpg)
Negative Resists:
Exposure to the UV light causes the negative resist to become polymerized, and more difficult to dissolve. Therefore, the negative resist remains on the surface wherever it is exposed, and the developer solution removes only the unexposed portions. Masks used for negative Photo resists, therefore, contain the inverse (or photographic "negative") of the pattern to be transferred.
![Page 9: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/9.jpg)
NEGATIVE AND POSITIVE PHOTORESIST
9
Mask/ reticle
Exposure
After Development
Negative Photoresist
UV light
Positive Photoresist
Substrate
Substrate
Substrate
Photoresist
Substrate
Photo resist
![Page 10: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/10.jpg)
BASIC STEP OF PHOTOLITHOGRAPHY
Photo resist coating Alignment and exposure Development
![Page 11: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/11.jpg)
BASIC STEPS
Wafer clean Dehydration bake Spin coating primer and PR Soft bake Alignment and exposure Development Pattern inspection Hard bake
![Page 12: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/12.jpg)
WAFER CLEAN
P-Well
USGSTI
Polysilicon
Gate Oxide
![Page 13: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/13.jpg)
PRE-BAKE AND PRIMER VAPOUR
P-Well
USGSTI
Polysilicon
Primer
![Page 14: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/14.jpg)
PHOTORESIST COATING
P-Well
USGSTI
Polysilicon
Photoresist
Primer
![Page 15: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/15.jpg)
SOFT BAKE
P-Well
USGSTI
Polysilicon
Photoresist
![Page 16: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/16.jpg)
ALIGNMENT AND EXPOSURE
P-Well
USGSTI
Polysilicon
Photoresist
Gate Mask
![Page 17: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/17.jpg)
ALIGNMENT AND EXPOSURE
Gate Mask
P-Well
USGSTI
Polysilicon
Photoresist
![Page 18: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/18.jpg)
POST EXPOSURE BAKE
P-Well
USGSTI
Polysilicon
Photoresist
![Page 19: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/19.jpg)
DEVELOPEMENT
P-Well
USGSTI
PolysiliconPR
![Page 20: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/20.jpg)
HARD BAKE
P-Well
USGSTI
PolysiliconPR
![Page 21: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/21.jpg)
PATTERN INSPECTION
P-Well
USGSTI
PolysiliconPR
![Page 22: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/22.jpg)
PHOTOLITHOGRAPHY CONTD…
The last stage of Photolithography is a process called ashing. This process has the exposed wafers sprayed with a mixture of organic solvents that dissolves portions of the photo resist . Conventional methods of ashing require an oxygen-plasma ash, often in combination with halogen gases, to penetrate the crust and remove the photo resist. Usually, the plasma ashing process also requires a follow-up cleaning with wet-chemicals and acids to remove the residues and non-volatile contaminants that remain after ashingDespite this treatment, it is not unusual to repeat the "ash plus wet-clean" cycle in order to completely remove all photo resist and residues.
![Page 23: Diffusion & photolithography process for electronic device manufacturing](https://reader030.fdocuments.us/reader030/viewer/2022033013/55d06c56bb61eb7b4a8b45e5/html5/thumbnails/23.jpg)
THANK YOU