BOQ for 5th Utility Buildings

UFLEX LIMITED (JAMMU DIVISION, UNIT-II) 04/08/2023

B. CIVIL COST FOR UTILITY BUILDINGS

S.No. Description Amount

1 Earth Work 432,099

2 Concrete Work 862,098

3 Steel Reinforcement Work 191,469

4 Form Work 258,701

5 Masonary Work 113,478

6 Plastering Work -

7 Structural Steel Work -

8 Roofing Work -

9 Flooring & False Ceiling -

10 Painting & Polishing Work -

11 Doors & Windows -

12 Miscellaneous Work -

Total (1 to 12) 1,857,846

Add: Work Contract Tax (WCT) 195,074

Grand Total with WCT 2,052,919

m/s Pal Construction Co. M/s U Flex Ltd Unit II

CIVIL COST FOR UTILITY BUILDINGS

EARTHWORK

Description Unit This bill qtyTotal Qty

Rate Amount

1.1

Cum 2641.35 0.00 2641.35 101 266,776

1.2

Cum 0.00 131 -

1.3

Cum 0.00 102 -

1.4

Cum 588.3 0 588.30 158 92,951

1.5

Cum 0.00 324 -

1.6

Cum 0.00 460 -

Item no.

previous qty

Earth work in excavation in all kinds of soil for basement, foundations, trenches, pits, drains etc. including all lifts and leads as per designs & drawings using manual or mechanical equipment and the method as approved by the Project Manager, at all locations as required including all labour, material, equipment, plant & machinery, shoring, planking, strutting, de-watering of rain water etc, loading, unloading, transportation and disposal of surplus spoils within site complex as directed by the Project Manager. The tenderer shall submit the methodology of execution for this item for approval of the Project Manager.

Rebate for - Handling & transporting surplus excavated material/Earth etc by trucks including loading and unloading etc., & disposing the same outside the plot boundaries at approved dump yard as directed including all labour, material, equipment, plant and machinery. Quantity to be arrived based on soil reconciliation. The rate shall include all lead & lift and cost towards getting permission from statutory authorities.

Filling with selected excavated earth obtained from excavation at site at all locations around foundations behind retaining wall, above raft, in plinth, plinth protection etc. as directed in layers not exceeding 20 cms in thickness, confining the fill, and consolidating/compacting the deposited layer by mechanical means / compactors, plate vibrators and watering etc., to achieve desired density as specified and as directed by the Project Manager.

Filling good earth free from vegetation brought from outside including supply as directed, in layers not exceeding 20 cms in thickness, confining the fill, and consolidating/compacting the deposited layer by mechanical means / compactors, plate vibrators and watering etc., to achieve desired density as specified and as directed by the Project Manager.

Supplying and filling with river sand under floors including spreading, confining, watering, ramming, consolidating, and final dressing to required level etc., at all depths complete including all labour, material, plant & machinery etc., as directed by the Project Manager.

Supplying and laying 120 mm thick well graded hard stone soling hand packed using 40mm nominal size stone ballast under floor including consolidation with one tonne hand roller and rammers etc. and filling the voids with coarse quarried sand, watering including all labour, material, plant & machinery etc., complete to achieve 90% compaction proved by taking proctor density test at locations approved as per drawing, specification and as directed by the Project Manager.



Rate Amount Item no.

previous qty

1.7

Sqm 494.91 164.97 659.88 110 72,372

Total carried over to summary 432,099

CONCRETE WORKS

2.1

a.Cum 113.94 35.28 149.215 1183 176,521

b.Cum 0 1183 -

c.Cum 0 1183 -

d.Cum 0 1622 -

2.2

Sqm 53.95 53.95 219 11,834

2.3

Sq.m 0 219 -

REINFORCED CEMENT CONCRETE 0 -

0 -

2.4

0 -

Providing and applying Pre-Constructional Anti-Termite treatment as per IS:6313 (part-2) 2001, in two operations, to create a continuous chemical barrier under plinth and back filling along the external perimeter of building, expansion joints, surroundings of pipes and conduits, drains etc. using CHLORYPYRIPHOS EC 20% with 1% concentration and quantity sprayed with pump in stages including all labour, material, equipment complete as per drawing, specification and as directed by the Project Manager. The works shall be carried out by an approved specialist agency providing guarantee against re-infestation for 10 years in approved format.

Providing, laying, and finishing plain cement concrete (PCC) using cement, sand, coarse stone aggregates in foundation bases, below floors as per design & drawing including dewatering, preparing surface, machine mixing, pouring in place, compacting, curing, including all labour, material, equipment, plant and machinery, conveyance, side shuttering lowering, wastages & all incidentals. etc. complete as per drawing, specification and as directed by the Project Manager.

Mix 1:4:8 (1 cement : 4 Coarse sand : 8 graded stone aggregate 40 mm & down size) at all levels

Mix 1:3:6 (1 cement : 3 Coarse sand : 6 graded stone aggregate 40 mm & down size) at all levels

Mix 1:5:10 (1 Cement : 5 Coarse sand : 10 graded stone aggregate 40 mm & down size) at all levels

Mix 1:2:4 (1 Cement : 2 sand : 4 graded stone aggregate 20 mm & down size) at all levels

Providing, mixing, laying, curing and finishing plain cement concrete (PCC) in Damp Proof Course of thickness 50mm including all material, labour, plant & machinery with 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 12mm & down size) complete, as per drawing, specification and as directed by the Project Manager.

Applying a coat of residual perrlumin bitumen of penetration 80/100 of approved quantity using 1.7 kg.m² on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

NOTE-steel and cement will be supplied by owner free of cost as per tender conditions

Providing, mixing, laying, finishing, curing at all levels and locations controlled cement concrete of grade M25 (minimum content of cement 300 kg/cum) machine batched, machine mixed, mechanically vibrated using PPC/OPC, course sand, graded stone aggregate 20mm down size including, dewatering, preparing surface, providing cement cover blocks, making construction joints, etc. complete as per drawing, specification and as directed by the Project Manager. . The rate to include all labour, material, equipment, plant & machinery,admixture, conveyance, lowering, hoisting, wastages, including cost of Design mix and all incidentals excluding formwork and reinforcement which shall be measured & paid for separately.




previous qty

IN SUB STRUCTURE 0 -

a.

Cum 291.35 62.76 354.11 1622 574,366

IN SUPER STRUCTURE 0 0 -

b.

Cum 26.559 31.59 58.149 1709 99,377

PRE CAST CONC. 0 0 -

2.5

Cum 0 2350 -


In foundation footings, raft, slab on grade, bases for retaining walls, column pedestrals, pedestals, and equipment/machine foundations,column footings,staircase footings, drains upto plinth level etc.,

In columns,floor slabs, beams,tie beams,lintels,curved beams, landings, balconies, chajjas, projections canopies,shelves / counters etc., at all levels

Providing, hoisting and fixing up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like including the cost of required centering, shuttering,




previous qty

STEEL REINFORCEMENT WORKS

3.1

a. MT 30.086 8.253824 38.339824 4994 191,469

b.MT 0 4994 -


FORM WORKS

4.1

IN SUB STRUCTUREa.

Sqm 875.59 64.18 939.77 88 82,700

IN SUPER STRUCTURE ( Ply Shuttering to be used )0 -

4.2 At all locations inclusive of rectangular & curved portions.0 -

a.

0 -

1) From Plinth upto 6.0 Mtr Height Sqm 363.57 245.7 609.27 289 176,002

2) From Plinth upto 9.0 Mtr Height Sqm 0 328 -

4.3

No.s 0 333 -


MASONRY WORK

Straightening, cutting, bending, fabricating to required shapes & sizes, placing in position, tying at all levels steel reinforcement as per drawings and details for reinforced concrete works, tying with double strand 18 SWG annealed binding wire, providing concrete cover blocks etc.,complete as per specification and as directed by the Project Manager. The rate to include all labour, material, equipment, plant & machinery, conveyance, lowering, hoisting, rolling margin, wastages and all incidentals. Only authorized laps, chairs & spacers shall be measured for payment. ( The rate shall include cost of binding wire)

TMT bars conforming to IS 1786 of all diametersMild steel bars conforming to grade I of IS 432 designated as Fe 410-S of all diameters

Providing, fabricating and erecting form work at all levels and places wherever needed/specified as per drawing including striking with 12mm Plastic coated, marine resistant waterproof ply/Smooth finished MS plates with adjustable steel props of acceptable Staging system and with sufficient bracing as approved by consultant. Cost to include designing of proper form work and staging system to suit the requirements,Submission of design calculations and shop drawings for approval,sealing the joints with heavy duty brown self adhesive tape, aligning to line and levels including M.S. Ties, PVC Spacer, Providing openings/ cutouts/ pockets, applying deshuttering chemical, Deshuttering as approved by the consultant etc., complete at all levels, heights and profiles for Note : Only plan area shall be considered.No extra shall be considered for Side shuttering of Drop panel/column capitals.

In foundation footings, raft, slab on grade, bases for retaining walls, column pedestrals, pedestals, and equipment/machine foundations,column footings,staircase footings, drains upto plinth level etc., (Ordinary shuttering will be used )

Columns,Beams, tie beams, curved beam, flat surfaces such as suspended floors, roofs, landings, balconies, chajjas projections, canopies curved slabs lintels, shelves/counter of any shape and design etc :-

Providing pockets and removing moulds for machine foundations including necessary arrangements to holding moulds in position (template) during casting of foundation as directed by the Project Manager.




previous qty

5.1

Cum 53.95 53.95 2103 113,478

5.2

Cum 0 2191 -

5.3

Sqm 0 377 -


Providing and constructing 230mm thick brick masonry in foundations and plinth upto plinth level using approved quality bricks of class designation 75 designs and drawings with cement mortar 1:5 (1 cement : 5 coarse sand) including raking out of joints or finishing joints flush, leaving holes, cut outs, openings, and making them good, leaving toothings for cross walls, curing of brick work, etc. complete as directed by Project Manager. The rate to include all labour, material, scaffolding, tools & tackles, plant & machinery, conveyance, storing, handling, wastages and other incidentals.

Providing and constructing 230mm thick brick masonry in super structure including in steps at all levels, locations, and heights using approved quality bricks of class designation 75 designs and drawings with cement mortar 1:5 (1 cement : 5 coarse sand) including raking out of joints or finishing joints flush, leaving holes, cut outs, openings, and making them good, leaving toothings for cross walls, curing of brick work, etc. complete as directed by Project Manager. The rate to include all labour, material, scaffolding, tools & tackles, plant & machinery, conveyance, storing, handling, wastages and other incidentals.

Providing and constructing 115 mm thick brick masonry at all levels and locations using approved quality bricks, of class designation 75 designs and drawings with cement mortar 1:4 (1 cement : 4 coarse sand) including raking out of joints or finishing joints flush, leaving holes and making good, curing of brick work. The rate to include supply , cutting, placing and tying in position 2 nos of 6 mm dia MS bars in bed joint reinforcement at every 4th course as per drawing detail, all labour, material, scaffolding, tools & tackles, plant & machinery, conveyance, storing, handling, wastages and other incidentals. etc. complete as directed by Project Manager.




previous qty

PLASTERING WORK

6.1 Internal plastering6.1.1

Sqm 0 88 -

6.1.2

Sqm 88 - -

6.2 External Plastering -

6.2.1

Sqm 150 -

6.3

Sqm 108 -

6.4

Sqm 125 -

Providing and applying up to 12mm cement plaster to fair side of brick works at all locations & levels in cement mortar 1: 6 (1 cement : 6 sand comprising of 50% coarse sand and 50% fine sand) to wall surfaces as per drawings and details including preparation of surface, hacking, scarifying & cleaning, champhering and rounded angles up to 80 mm girth, curing , cleaning etc. complete as per specification and as directed by the Project Manager.. The rate to include all labour, material, scaffolding, tools & tackles, plant & machinery, conveyance, storing, handling, wastages and other incidentals complete.

Providing and applying up to 15mm cement plaster to rough side of brick works at all locations & levels in cement mortar 1: 6 (1 cement : 6 sand comprising of 50% coarse sand and 50% fine sand) as per drawings and details including preparation of surface, hacking, scarifying & cleaning, champhering and rounded angles up to 80 mm girth, curing , cleaning etc. complete as per specification and as directed by the Project Manager. The rate to include all labour, material, scaffolding, tools & tackles, plant & machinery, conveyance, storing, handling, wastages and other incidentals complete.

Providing and applying 18 mm water proof cement plaster to external surfaces in two coats under layer 12mm thick with cement mortar 1:4 (1 cement : 4 coarse sand) and a top layer of 6mm thick cement plaster 1:6 ( 1 cement: 6 coarse sand) at all locations & levels, sponge finished with water proofing compound in the proportions as per manufacture's specification to masonry / concrete surfaces as per drawings and details including preparation of surface, hacking, scarifying & cleaning, curing , cleaning etc. complete as per specification and as directed by the Project Manager. The rate to include all labour, material, scaffolding, tools & tackles, plant & machinery, conveyance, storing, handling, wastages and other incidentals complete. Rate to include furnishing 10 years guarantee for bone dry surface on opposite side of treated surface.

Providing and applying 6mm thick cement plaster to concrete ceiling bottom surfaces of mix 1:4 (1 cement :4 fine sand) at all levels including all labour, scaffolding, material, tools & tackles, plant & machinery, conveyance, storing, handling, wastages and other incidentals complete as per specification and as directed by the Project Manager.

Providing and applying up to 6 mm cement plaster to vertical surfaces at all locations & levels in cement mortar 1: 3 (1 cement : 3 sieved sand) to concrete surfaces as per drawings and details including preparation of surface, hacking, scarifying & cleaning, chamfering and rounded angles up to 80 mm girth, curing , cleaning etc. complete as per specification and as directed by the Project Manager. The rate to include all labour, material, scaffolding, tools & tackles, plant & machinery, conveyance, storing, handling, wastages and other incidentals complete.




previous qty

6.5

Sqm 114 -

6.6

Sqm 202 -

Total carried over to summary -

STRUCTURAL STEEL WORK

7.1

MT 11831 -

-

(i) -

(ii)

-

(iii) -

(iv) Steel frame work for false ceiling including suspenders -

(v) In supporting structure for Polycarbonate roofing sheet -

(vi) Cat walk including necessary ladder -

-

Providing and applying 12mm thick cement plaster to PCC/lean concrete surfaces of mix 1:4 (1 cement :4 fine sand) at all levels including all labour, scaffolding, material, tools & tackles, plant & machinery, conveyance, storing, handling, wastages and other incidentals complete as per drawing, specification and as directed by the Project Manager.

Providing and fixing 150mm wide chicken wire mesh 24 guage and 20 nesh at junction, of RCC and masonary works, including fixing in position and nails of 25mm length required gauge and at required distance as directed by the Project Manager.

The rate shall include all cost towards preparation and obtaining approval of fabrication drawing including BOM, erection sequence, method statements, temporary supports and structures, from consultants/Project Managers prior to execution etc., complete as per drawing, specification and as directed by the Project Manager.

Fabricating, assembling hoisting and fixing in position to alignments and levels as per approved drawings structural steel work in built up roof truss girders with booms, lattice girders, roof trusses, gable frame, built up purlins, columns etc. to detail, of welded and bolted construction comprising of R.S. joists, channels, angles, plates, rounds cleats, gusset plates including base plates etc. necessary permanent rivets, bolts and nuts, handling, straightening, cutting, holing, welding, shop erection, transport to site including loading & unloading, storing, handling, etc. and painting with a shop coat Zinc Phosphate primer prior to erection & also including Enamel Paint with Two or More Coats.

The rate shall include Providing & applying at all locations & level two or more coats of synthetic enamel paint of approved make & shade over two coats of approved anti corrosive primer Zinc phosphate- including cleaning, surface preparation, sand papering, applying filler/putty, scaffolding, labour, material, plant and machinery etc., complete as per manufacturers recommendation and as directed by the Project Manager.

In truss, lattice girders, bracings, base plate & gusset plate, etc.,

In built up columns, cladding columns for supporting cladding runners, self supporting panel, pipes & tie beams, base plate & gusset plate for column and rain water pipe protection

In purlins, cladding runner base plate, gusset plate, and sag rods

(Payment will be made on the basis of standard section weights for net weight erected in position excluding rivets, temporary bolts etc. but rate should include the cost of permanent bolts, nuts and washers as required and approved. (No measurement shall be taken for payment of permanent bolts and nuts).




previous qty

7.2

Rmt 1227 -

Total Carried over to summary -

ROOFING

8.1

Sqm 526 -

8.2

Sqm 526 -

Fabrication and fixing in position gutter made out of M.S.sheets (3mm thick X 1.5m wide ) bent to shape as required, joints welded and provided with collars to suit outlets of 160/200mm dia PVC pipe fixed to the gutters at outlet points to required slopes with all fixing accessories such as 50x6mm M.S flats & 12mm dia round rods with bolts & nuts at 900mm c/c for adjustment of levels all complete. including Enamel Paint all M.S. work . At least 5M length of gutter shall be fabricated before erection. Only weld at every 5M intervals is allowed in site. (The contractor to prepare and submit shop drawings for the approval of Architect/Project Manager prior to commencement).

The rate shall include all cost towards preparation and obtaining approval of fabrication drawing including BOM, erection sequence, method statements, temporary supports and structures, from consultants/project manager prior to execution etc., complete as per drawing, specification and as directed by the Project Manager.

Designing, obtaining approval, providing and fixing in colour coated GALVALUME sheets in roofing made out of 0.5MM TCT.550 Mpa cold rolled sheet with hot dip metallic coating of aluminium zinc alloy 150gms/sqm having 975/1000mm cover width with 20-30 mm high crest , in lengths to suit site requirements and shall be fixed with necessary suitable imported galvanized carbon steel self drilling & self tapping screws of HILTI/BOSCH of required diameter and length all complete with EPDM sealing washers with sealent, flashing of required size & shapes including providing necessary trim, fillers, sealent, including apron pieces wherever required. Rate should include cost of plastic caps of approved colour of U.V resistance and button bolts, all consumables all as per manufacturer's specification ., complete as per architectural drawings, specifications and as directed by the Project Manager.

Designing, obtaining approval, providing and fixing colour coated GALVALUME sheet in wall cladding made out of 0.5mm TCT.550 Mpa cold rolled sheet with hot dip metallic coating of aluminium zinc alloy 150gms/sqm with 20 microns on top with silicon modified polyester or High density polymer coating and 5 microns back up epoxy coating at the bottom having 975/1000mm cover width with 20-30 mm high crest in lengths ato suit site requirements and fixed with necessary suitable imported galvanized carbon steel self drilling & self tapping screws of HILTI/BOSCH of required diameter and length all complete with EPDM sealing washers with sealant. Rate should include cost of plastic caps of approved colour of U.V resistance and button bolts, all consumables all as per manufacturer's specification., complete as per architectural drawings, specifications and as directed by the Project Manager.




previous qty

8.3

Sqm 298 -

8.4

Sqm 881 -


FLOORING / FALSE CEILING WORK

9.1a

sqm 294 -

9.1b

sqm 392 -

9.1c

rm 147 -

9.2

Rm 118 -

9.3

sqm 783 -

9.4

0 -

a Ceramic glazed tiles sqm 734 -

Designing, obtaining approval, providing and fixing underdeck insulation system using resin bonded glass wool 50mm thk (minimum density 20kg/cum) , double side reflective foil Laminate and wire mesh as per approved designs, to support the insulation as per approved design, provisions for fixing of accessories such as light fixtures, false ceiling etc., as per architectural drawings, specifications, approved shop drawing, manufacturer's specification etc., complete as directed by the Engineer.

Designing, Obtaining approval, providing and fixing JMBS 88/200 ( plain trpezoidal deck sheet of 88mm deep, 200mm pitch), 1.0mm BMT (Base Metal thickness), 240 Mpa with Zinc Coating of 120 gm/m2 total on both sides, with adequate to ensure proper bonding between concrete and steel deck sheeting & fixed with necessary scres to the supporting members. Rate should include all costs towards approval from Engineer incharge / PM, fixing of shear studs and all cosumables as per manufacturer's specification complete and as directed by Project Manager.

Providing and laying 100mm thick (average thickness) M20 grade design mixed concrete for nonslippery, Vacuum dewatered flooring including cleaning, trimming, watering the surface, laying in strips to required levels, trovelling, smoothening curing including providing hard top using Nitofloor hardner @ 3kg/Sqm (from Fosroc chemicals or equivalent) etc.,complete

Providing and laying 150mm thick (average thickness)M20 grade design mixed concrete for nonslippery, Vacuum dewatered flooring including cleaning, trimming, watering the surface, laying in strips to required levels, trovelling, smoothening curing including providing hard top using Nitofloor hardner @ 3kg/Sqm (from Fosroc chemicals or equivalent) etc.,complete

Over and above Item 10.1 for cutting grooves of size6mmx10mm at control joints and filling the grooves with Sealent(Colpor - 200 from Fosroc chemicals or equivalent)

18 mm thick flush Cement plaster skirting (up to 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement

25 mm thick Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand)

Providing and laying 1st quality of ceramic tiles of minimum 8 mm thick and all sizes but not less than 300x450mm) of approved make confirming to IS: 15622 in all colors except bottole green, burgundy, black in skirting, risers of steps and dado with cement based high polymer modified quickset adhesive (water based) confirming to IS: 15477 using 10 kg adhesive per sqm of tile area in average 6 mm thickness including with pointing in white cement mixed with pigment of matching shade complete.




previous qty

9.5

sqm 881 -


PAINTING AND POLISHING

10.1

sqm 69 -

10.2

SQM 196 -

10.3

0 -

a) On Walls upto 4.0mtr High sqm 71 -

b) on M.S. Work sqm 69 -


DOORS AND WINDOWS11.1

sqm 2103 -

11.2

sqm 1578 -

11.3

sqm 2629 -

11.4

sqm 359 -

11.5

sqm 455 -

Supplying 600x600mm grid ceiling suspension system consisting of 24 mm exposed metal grids T-section designed for maximum strength with white powder coated exposed face flanges. Suspension system (Hot Dipped galvanised steel) sections consists of Main runner of T-shapeed section with single rotary stiching made of GS sheet and of size 24mm X 38mm and 3600mm long, Cross Runners of T-shaped with double rotary stiching made of GS sheet and of size 24mm X 30/25mm an 1200/600mm long and Perimeter Section which cosists of perimeter wall angle made from 0.45mm thick GS sheet and of size 22mm X 22mm and 3000mm long, colour white. Grid system (main & cross) to be suspended from the roof with G.I wire rods etc. i/c providing extra framework and making openings for electrical fittings, A.C diffusers, trap doors etc. complete as per manufacturer specifications and detailed drawings and as directed by the architect at all levels. the rates shall include cost of providing aluminum non perforated tiles

Finishing the walls with two or three coats oil bourn distemper of approved brand and manufacture of required colour to give an even shade on internal wall surface.

Exterior Surface paint with APEX or equvalent whether proof paint two or more coats of approved brand and manufacture and of required shade to give an even shade I/c priming coat of cement primer , preparing base.

Painting on MS work with two or three coats synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :-

Providing and fixing35 mm thick ISI marked flush door shutters conforming to IS: 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands including ISI marked stsinless hinges as per approval of atchitect

For flush door shutters Extra for providing teak veneering on one side instead of commercial veneering

Extra if louvers (not exceeding 0.2 sqm) are provided in flush door shutters (overall area of door shutters to be measured).

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to M. S.steel frames etc. including welding bolting all complete

Providing and fixing 1mm thick M.S. sheet sliding-shutters with frame and diagonal braces of angle iron, 3mm M.S. gusset plates at the junction and corners with pulley, and angle and T-iron guide at the top and bottom respectively including applying a priming coat of approved steel primer as per design supplied by architect (only structural steel will be supplied by owner)




previous qty

11.6

sqm 3506 -

11.7nos 6135 -

11.8

sqm 3024 -

11.9

sqm 3330 -

11.10

sqm 219 -

11.11

nos 1096 -

11.12

nos 832 -

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5cm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters of 80x1.25mm M.S. laths with 1.25 mm thick top cover. including ball bearing etc all complete

Extra for providing mechanical device chain and crank operation for operating rolling shutters

Providing and fixing aluminum work for partitions with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. the work shall include push plate,toughen glass of 6mm thickness on upper part of partition/ door and both side prelam board at lower part, kick plate as per manufactuters details. all fixed portion of partitions will be provided with toughned glass including frame all complete

Providing and fixing aluminum work windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. the work shall include push plate,toughen insulated double glazing of 5 mm thick glass with 25mm gap as per manufactuters details

Providing and fixing 50 micron UV protected sun protection film of 3M on fixed/ openable glass portions, all complete as per architectural drawings and the directions of Engineer-in-charge.

P & F brass body mortice latch & lock with stainless steel tubular round knobs handles of approved model & make complete with all accessories and necessary screws etc.

Providing and fixing exposed type hydraulic door closure aluminium sleek body of approved quality and make complete as per IS 3564 -1970.




previous qty

11.13

nos 2805 -

11.14 P & F door buffer SS finish of approved sample. nos 789 -

11.15

rm 306 -

Providing and fixing double action hydraulic floor spring of approved brand as per IS 6315 or Hardwyn model 3000 with stainless steel cover plate for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece MS sheet outer box with slide plate complete

Providing and fixing pressed steel door frames confirming to IS: 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by architect




previous qty

11.16

sqm 1578 -

11.17

kg 10 -


MISCELLANEOUS12.1

MT 11831 -

12.2

nos 439 -

12.3

nos 175 -

12.4

rm 147 -

Total Carried over to summary

-

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators side /top /centre hung with beading and all members such as K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted with 15x3mm lugs, 10cm long, embedded in cement concrete blocks 15x10x10cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of hinges, pivots, float glass panes with providing and fixing steel beading of approved shape and section with screw and a priming coat of approved steel primer excluding the cost of metal beading and other fittings except necessary hinges or pivots complete as per approved design

Fabricating & Fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with dash fastener or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer

Fabrication & fixing MS insert plates,sleeves with necessary holdfasts, Edge protection angles as per drawing including providing and applying one coat of primer to exposed surface and grouting with Lockset or equivalent compound as per manufacturer's specifications and guidelines etc complete including all labour, material plant and machinery etc., complete as per drawings and details and as directed by the Project Manager.

Providing and grouting for foundation bolts, base plates, pockets etc. using approved make non shrink grout with suitable form work as per the manufacturers' recommendation, including co-ordinating with the other agencies complete as per drawing and as directed by the Project Manager. The rate shall include all materials, labour and incidentals.

Providing and fixing MS foundation bolts as per IS 2062, of dia varying from 16mm to 24 mm in position to correct alignment and level in RCC works including coordinating with the other agencies complete as per design drawing, specification and as directed by the Project Manager.

Providing and fixing 150 dia PVC rain water pipes. Pipes including all bends, tees, elbow etc including cutting and making good the walls etc. complete as per specifications and instruction of architect.

BOQ for 5th Utility Buildings

Documents

Transcript of BOQ for 5th Utility Buildings