ARJOWIGGINS Katalog
description
Transcript of ARJOWIGGINS Katalog
inkjet sublimation
papers
digitallaser paper
coated cold peel papers
hot split
papers
inkjet sublimation
papers
transferpapers
coated cold peel papers
hot split
paper
transfer
papers
inkjet sublimation
papers
digitallaser paper
coated cold peel papers
hot split
paper
inkjet sublimation
papers
digitallaser paper
coated cold peel papers
hot split
paper
by Arjowiggins
by Arjowiggins
by Arjowiggins
screen printinghot split
inks
screen printing
conventional inks
screen printing
water based inks
litho offsetconventional
backing
litho offsetwater based
baking
ink jetsublimation
inks
digital laserwater based
backing
HS90 • - - - - - -
X90 • - - - - - -
T75 - • • • - - -
T105 - • • • - - -
WB90 - • • • • - -
Z95 - • - - - - -
Textured - • - - - - -
Sublimage 73 - - - - - • -
Sublimage 93 - - - - - • -
Digipeel - - - - - - •
hot split
coated
cold peel
digital laser
inkjet
sublimation
Printing processProduct
Product range
PRINTING METHOD
• Screen printing of one or several colours with appropriate hot split inks
• Ideal for puff transfers (X90)
MAIN ADVANTAGES
• No curling
• Good dimensional stability
• Easy to peel
• High ratio of ink transfer
• Ease of release and matt finish, giving a soft feel result
• Sharp images and bright colours
HOT SPLIT PAPER Screen Printing Hot Split Transfer“X 90” cOATEd & “HS90” uncOATEd
Open the reams
Screen print each colour
Pre shrink the paper in the drying tunnel Cover the paper until screen printing step
Heat press the design on the garment within 6 months after printing
Cure each screen printed ink in a drying tunnel
130 °C 30 seconds
Make a rollingtest to check if the curing is ok
355 - 365 °F35 - 45 PSI
180 - 185 °C2,5 - 3 Bars8 - 10 Seconds
355 - 365 °F30 - 35 PSI
180 - 185 °C2 - 2,5 Bars8 - 10 Seconds
HotPeel
Cut and wrap the printed sheets in a sealed plastic bag
130 °C 30 seconds
HotPeel
fibers
To enhance washing resistance :After the last colour, and just prior entering in the drying tunnel, spray adhesive powder.
Remove excess of powder by shaking
To avoid miss registering,cover the printed sheets in between each printed colour
STEP 1
STEP 2
STEP 3
STEP 4
fibers
HS 90 & X90 Hot Split Inks X90 with Puff Inks
PRINTING METHOD
• Screen printing of one colour + adhesive layer or powder (T75, Z95)
• Screen printing of one or several colours + adhesive layer or powder (T105, Textured)
• Please note that Z95 is not suitable for water based inks
• For Textured, need to pre shrink the paper if use of water based ink on screen printing
MAIN ADVANTAGES
• No curling
• Good dimensional stability
• Easy to peel
• 100% ink transfer
• Sharp images and bright colours
• Ease of placement with Translucency (Z95 only)
• Embossed surfaces (Textured only)
cOATEd cOLd PEEL PAPERS ScREEn PRInTInG “T75”, “T105”, “Z95”, & “TEXTuREd”
Screen Printing cold Peel Transfer
Open the reams Print on top side
Screen print each colour
Pre shrink the paper in the drying tunnel Cover the paper until screen printing step
Cure each screen printed ink in a drying tunnel
TopSide
TopSide
130 °C 30 seconds
Make a rollingtest to check if the curing is ok
340 - 355 °F35 - 45 PSI
170 - 180 °C2,5 - 3 Bars5 - 15 Seconds
Wait at least15 SecondsCold Peel
Cut and wrap the printed sheets in a sealed plastic bag
130 °C 30 seconds
fibers
To enhance washing resistance :After the last colour, and just prior entering in the drying tunnel, spray adhesive powder.
Remove excess of powder by shaking
To avoid miss registering,cover the printed sheets, in between each printed colour
Heat press the design on the garment within 6 months after printing
STEP 1
STEP 2
STEP 3
STEP 4
PRINTING METHOD
• Offset litho printing + screen printing of a backup with conventional inks (T75, T105, WB90)
• Offset litho printing + screen printing of a backup with water based inks (WB90 only)
MAIN ADVANTAGES
• Optimal offset litho printing result without using an excessive amount of ink
• No curling
• Good dimensional stability
• Easy to peel
• 100% ink transfer
• No ink offset thanks to double side release coating
• Environmentally and customer friendly, when used with suitable water based ink backing (WB90 only)
cOATEd cOLd PEEL PAPERS LITHO PRInTInG “T75”, “T105”, & “WB90”
Litho Offset cold Peel Transfer
Conventional backing Water based backing
fibers
Litho printing
Screen print the white backing
Cure the screen printed backing in a drying tunnel
heat press the design on the garment within 6 months after printing
White backing shorter than offset printing (around 0,5 mm)
Cover
5 days 7 daysAND WAIT OR TO
No drying of the offset inks
48 H 72 HTO
130 °C 30 secondsMake a rollingtest to check if the curing is ok
340 - 355 °F35 - 45 PSI
170 - 180 °C2,5 - 3 Bars5 - 15 Seconds
Wait at least15 SecondsCold Peel
Cut and wrapin plastic bags
STEP 1
STEP 2
STEP 3
STEP 5
STEP 4
Open the reams Print on top side
TopSide
TopSide
TopSide
PRINTING METHOD
• Ink jet printing using dye sublimation inks
MAIN ADVANTAGES
• Excellent paper stability – no cockling
• Excellent dot definition and no ink bleed
• Artwork details fully obtained
• Fast ink drying time
• High transfer rate, giving vibrant colours when transferred
InKJET SuBLIMATIOn PAPERS “SuBLIMAGE 73” & “SuBLIMAGE 93”
Ink Jet Sublimation
Transfer on 100% polyester fabric and blend of 50% polyester and 50% cotton
Ink jet printing with dye sublimation inks
Heat press transfer in sheets
Reel to reel heat transfer using calendar
430 - 450 °F35 - 45 PSI
220 - 230 °C2,5 - 3 Bars20 - 30 Seconds
300 - 410 °F
150 - 210 °C15 - 40 Seconds
STEP 1
STEP 2
digital Laser Transfer For Textile
“spray” hot melt powder AP55 , shake to remove excess
L DIGIPEEL
L DIGIPEEL
Unwrap the paper
Screen print white BB55 backing or clear TB55 backing wider than laser printing (around 0,5 mm)
Colour laser copiers and desktop laser printers ( preprint / by pass )
Heat press within 6 months after printing
Cure screen printed backing and hot melt powder in a drying tunnel
Print withmirroreffect
330 - 340 °F45 - 55 PSI
170 - 180 °C3 - 3,5 Bars10 - 15 Seconds
Wait at least 15 Seconds Cold Peel
Washing conditions :
temp max 30°C
130 °C 30 seconds
Universal back up BB55 white or TB55 clear Mixed with retarding agent RE55 (up to 5%)
to limit screen clogging
In case of short oven or natural drying you can add accelerator AC55 up to 3%in the Universal backings BB55 or TB55
Cut and wrap the printed sheets in a sealed plastic bag
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
DIGIPEEL
DIGIPEEL DIGIPEEL
DIGIPEEL DIGIPEEL
DIGIPEEL DIGIPEEL
DIGIPEEL DIGIPEEL
DIGIPEELDIGIPEEL
DIGIPEELDIGIPEEL
DIGIPEEL DIGIPEEL
DIGIPEEL
PRINTING METHOD
• Laser printing on desktop printers or laser colour copiers + screen printing of a backup with specific water based inks + adhesive powder
• List of printers & copiers which have been successfully tested available upon request
MAIN ADVANTAGES
• No curling
• Good dimensional stability
• Sharp images and bright colours
• Smooth easy release
• 100% ink transfer
• Environmentally and customer friendly, when using recommended water based ink backing
• Innovative low cost solution for small series production runs
• Suitable to use for sampling on large litho series production runs
dIGITAL LASER PAPER “dIGIPEEL 80”
SUBLIMAGE
SUBLIMAGE
SUB
SUBLIMAGESUBLIMAGESUB
G R A P H I C Prin
ted
on S
atim
at 3
50 g
, FS
C c
ertifi
ed p
aper
SG
S-C
OC
-003
161