Post on 12-Apr-2015
Nokia Siemens Networks WCDMA RAN, Rel. RU20, Operating Documentation, Issue 02
WCDMA RAN RNW consistency checking rules
DN0934038
Issue 01AApproval Date 2010-03-26
2 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d805807274e1
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.
The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2010. All rights reserved
f Important Notice on Product Safety Elevated voltages are inevitably present at specific points in this electrical equipment. Some of the parts may also have elevated operating temperatures.
Non-observance of these conditions and the safety instructions can result in personal injury or in property damage.
Therefore, only trained and qualified personnel may install and maintain the system.
The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to comply with the applicable safety standards.
The same text in German:
Wichtiger Hinweis zur Produktsicherheit
In elektrischen Anlagen stehen zwangsläufig bestimmte Teile der Geräte unter Span-nung. Einige Teile können auch eine hohe Betriebstemperatur aufweisen.
Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Körperverlet-zungen und Sachschäden führen.
Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertes Personal die Anlagen installiert und wartet.
Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Geräte müssen die zutreffenden Sicherheitsbestimmungen erfüllen.
DN0934038Issue 01A
3
WCDMA RAN RNW consistency checking rules
Id:0900d805807274e1
Table of ContentsThis document has 69 pages.
1 Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 ADJD consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 ADJG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5 ADJI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6 ADJS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7 CMOB consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8 COCO consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9 FMCG consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10 FMCI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
11 FMCS consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
12 HOPG consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
13 HOPI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
14 HOPS consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
15 IPNB consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
16 IPQM consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
17 IU consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
18 IUR consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
19 RNC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
20 TQM consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
21 WANE consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
22 WBTS consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
23 WCEL consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
24 WLCSE consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
25 WRAB consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
26 WSG consistency checking rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
27 WSMLC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
4 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d805807274e1
List of TablesTable 1 Rule and description attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Table 2 ADJD consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Table 3 ADJG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Table 4 ADJI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Table 5 ADJS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Table 6 CMOB consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Table 7 COCO consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Table 8 FMCG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Table 9 FMCI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Table 10 FMCS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Table 11 HOPG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Table 12 HOPI consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Table 13 HOPS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Table 14 IPNB consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Table 15 IPQM consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Table 16 IU consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Table 17 IUR consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Table 18 RNC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Table 19 TQM consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Table 20 WANE consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Table 21 WBTS consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Table 22 WCEL consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Table 23 WLCSE consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Table 24 WRAB consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Table 25 WSG consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Table 26 WSMLC consistency checking rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
DN0934038Issue 01A
5
WCDMA RAN RNW consistency checking rules Summary of changes
Id:0900d8058070fa5c
1 Summary of changesChanges between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.
Note that the issue numbering system is changing. For more information, see Guide to WCDMA RAN Documentation.
Issue 01ANew consistency checking rules
– ADJDADJD_CM_0013
– ADJIADJI_CM_0009ADJI_CM_0010
– ADJSADJS_CM_0009ADJS_CM_0010ADJS_CM_0011ADJS_CM_0012
– FMCSFMCS_CM_0004
– RNCRNC_CM_0033RNC_CM_0034RNC_CM_0035RNC_CM_0036RNC_CM_0037RNC_CM_0038RNC_CM_0039RNC_CM_0040RNC_CM_0041
– WBTSWBTS_M_0011
– WCELWCEL_CM_0026WCEL_CM_0023WCEL_CM_0028
Modified consistency checking rules
– IUIU_CM_0003
Removed consistency checking rules
– RNCRNC_CM_0011
6 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa5c
Summary of changes
– WCELWCEL_CM_0021WCEL_CM_0029WCEL_CM_0095
Issue 01This is the first issue of the document.
DN0934038Issue 01A
7
WCDMA RAN RNW consistency checking rules Introduction
Id:0900d8058070fa5e
2 IntroductionThis document describes the additional checking performed between different Radio Network managed objects and RNW configuration management parameters during operations targeted to RNW managed objects.
The RNW consistency check is a service provided by the RNC and performed during the download of the RNW plan. The same consistency rules apply to the configuration tasks carried out by by RNW Object Browser application in RNC Element Manager.
The parameter data in different RNW objects is compared to each other to check if the data is consistent according to the parameter relationship definitions.
During the RNW parameter modification, it is also checked that the parameter value is within the valid range. This parameter range check is performed before the consistency check, and thus it is not included in the consistency checking rules described in this doc-ument. For more information about the value ranges of the different RNW parameters, see WCDMA Radio Network Configuration Parameters.
For information on the functional areas of the radio network and related parameters, see the functional area descriptions in WCDMA RAN System Library.
Consistency checking rules are grouped according to managed objects in this docu-ment. Under the managed object, rules are arranged by the operation type and the rule identifier. For each rule there is a defined own unique identifier. The identifier consists of the managed object, the operation type and the number. The number is unique within the managed object and the operation type.
The rules are presented in the table layout. The following table presents the attributes for each rule and description of the attributes.
Entry Description
Checking rule identifier (ID) The unique identifier for the rule. The format is ‘ManagedObject_OperationType_FourDigitNumber’, for example, WBTS_C_0002. The following abbreviations are used for operation type:
– C (Creation)– CM (Creation and Modification)– M (Modification)– D (Deletion)– U (Unlock (valid for WCEL only))
RNW Managed Object type This attribute defines for which RNW managed object the rule is valid.
Operation type This attribute defines the operation for which the rule is valid and con-sistency check is performed.
Check description This attribute defines the actual checking performed during the oper-ation.
Error text This attribute defines the error text returned if the consistency check rule is not fulfilled.
Table 1 Rule and description attributes
8 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa60
ADJD consistency checking rules
3 ADJD consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
ADJD_C_0001 ADJD Create ADJDId must be unique within the parent WCEL
ADJD ALREADY CREATED UNDER WCEL
ADJD_C_0002 ADJD Create The maximum amount of ADJD under the WCEL is 32
MAXIMUM OF ADJDS FOR WCEL
ADJD_CM_0001 ADJD Create/Modify The option 'Detected Set Reporting Based SHO' must be supported
ADJD CANNOT BE CREATED OR MODIFIED IF FEATURE STATE OF DETECT SET REPORTING BASED SHO OFF
ADJD_CM_0002 ADJD Create/Modify AdjdRTHopsId and AdjdN-RTHopsId must refer to the existing HOPS object (Intra-frequency Handover Path)
HOPS NOT FOUND
ADJD_CM_0003 ADJD Create/Modify The scrambling code must be different between the ADJD and the source WCEL
ADJD AND SOURCE CELL MUST HAVE DIFFERENT PRIMARY SCRAMBLING CODE
ADJD_CM_0004 ADJD Create/Modify The same scrambling code is not allowed for other ADJD of the source WCEL
PRIMARY SCRAMBLING CODE MUST BE UNIQUE WITHIN ADJD OF THE SAME SOURCE CELL
ADJD_CM_0005 ADJD Create/Modify The same scrambling code is not allowed for any ADJS of the source WCEL
PRIMARY SCRAMBLING CODE OF AN ADJS AND AN ADJD OF THE SAME SOURCE WCEL MUST BE DIFFERENT
ADJD_CM_0006 ADJD Create/Modify ADJD must have a unique target WCEL among ADJDs under the source WCEL
THE SAME TARGET CELL IS POINTED BY AN ADJD OF THE SAME SOURCE CELL
ADJD_CM_0007 ADJD Create/Modify ADJD must have a different target WCEL from any ADJS under the source WCEL
THE SAME TARGET CELL IS POINTED BY AN ADJS OF THE SAME SOURCE CELL
ADJD_CM_0008 ADJD Create/Modify The following parameters must be the same in ADJD and the target WCEL: AdjdMCC, Adjd-MNCLength, AdjdMNC, AdjdLAC, AdjdRAC, AdjdScr-Code, AdjdCPICHTxPwr
PARAMETERS IN ADJ DEFI-NITION DO NOT MATCH WITH TARGET CELL
Table 2 ADJD consistency checking rules
DN0934038Issue 01A
9
WCDMA RAN RNW consistency checking rules ADJD consistency checking rules
Id:0900d8058070fa60
ADJD_CM_0009 ADJD Create/Modify The UARFCN of the source and the target WCEL must be the same
SOURCE AND TARGET CELLS MUST HAVE SAME FREQUENCY IN ADJD
ADJD_CM_0010 ADJD Create/Modify When the source WCEL is HSDPA-enabled, AdjdHS-DPAHopsId must be defined
HSDPA HOPS ID MUST BE DEFINED FOR OUTGOING ADJD OF HSDPA ENABLED CELL
ADJD_CM_0011 ADJD Create/Modify When the source WCEL is HSDPA-enabled, and HSDPA with AMR is enabled in the RNC, AdjdRTWithHSDPA-HopsIdmust be defined
RT HSDPA HOPS MUST BE DEFINED FOR ADJD OF HSDPA ENABLED CELL IF RNC SUPPORTS AMRWITH-HSDSCH
ADJD_CM_0012 ADJD Create/Modify If AdjdHSDPAHopsId is defined, the referred HOPS must exist
HOPS NOT FOUND
ADJD_CM_0013 ADJD Create/Modify If AdjdRTWithHSDPAHopsId is defined, the referred HOPS must exist
HOPS NOT FOUND
ADJD_CM_0014 ADJD Create/Modify If the cell is controlled by the local RNC, ADJD -ADJDTX-DIV cannot be modified
IF THE CELL IS CON-TROLLED BY THE LOCAL RNC, ADJD -ADJDTXDIV CAN NOT BE MODIFIED
ADJD_M_0001 ADJD Modify The parameters related to the target WCEL except AdjdRN-CId (AdjdMCC, AdjdMNC-Length, AdjdMNC, and AdjdCI) cannot be modified when the target cell is under the same RNC
TARGET CELL OF THE ADJACENCY IS NOT ALLOWED TO CHANGE IF TARGET CELL IS UNDER THE SAME RNC
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 2 ADJD consistency checking rules (Cont.)
10 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa64
ADJG consistency checking rules
4 ADJG consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
ADJG_C_0001 ADJG Create ADJGId must be unique within the parent WCEL
ADJG ALREADY CREATED UNDER WCEL
ADJG_C_0002 ADJG Create The maximum amount of ADJG under the WCEL is 32
MAXIMUM OF ADJGS FOR WCEL
ADJG_CM_0001 ADJG Create/Modify BCCH and BSIC must be dif-ferent between separate ADJG definitions
BCCH AND BSIC MUST BE DIFFERENT BETWEEN SEPARATE ADJG DEFINI-TIONS
ADJG_CM_0002 ADJG Create/Modify ADJG with the same target WCEL must not exist
THERE IS ALREADY ANOTHER ADJ POINTING TO SAME TARGET UNDER THIS WCEL.
ADJG_CM_0003 ADJG Create/Modify If ADJGId is 0 and the parame-ter AMRDirReCell of the FMCG that the source WCEL points with RtFmcgIdentifier has the value Enabled, the value of AdjgSIB cannot be No, i,e, the ADJG must be included in System Information.
ADJG-AdjgSIB SHOULD NOT BE SET AS 0 (NO) WHEN AMR CALL INTERSYSTEM HANDOVER IS ON
ADJG_CM_0004 ADJG Create/Modify If the ADJG is GAN-specific (BCCH and BSIC is same as RNC parameters GANetwAR-FCN, GANetwNCC and GANetwBCC), AdjgSIB must be No, i.e., GAN-specific ADJG cannot be included in System Information.
GAN ADJG CAN EXIST ONLY WHEN GSM NEIGHBOUR CELL IS NOT INCLUDED IN THE SYSTEM INFORMA-TION
ADJG_CM_0005 ADJG Create/Modify If the option 'UTRAN - GAN interworking' is ON, and the option 'GSM ISHO' is OFF, only the GAN-specific ADJG can be configured.
ADJG GAN RELATED PARAMETERS NOT SAME WITH RNC PARAMETERS GANetwARFCN, GANetwNCC AND GANetwBCC
ADJG_CM_0006 ADJG Create/Modify Normal ADJG (not GAN spe-cific) – RtHopgIdentifier and NrtHopgIdentifier must refer to the existing HOPG object (Inter-system Handover Path)
HOPG NOT FOUND
Table 3 ADJG consistency checking rules
DN0934038Issue 01A
11
WCDMA RAN RNW consistency checking rules ADJG consistency checking rules
Id:0900d8058070fa64
ADJG_CM_0007 ADJG Create/Modify As for normal ADJG (not GAN specific), RT+NRT FMCG must be defined for the source WCEL
FMCG ID NOT DEFINED FOR THE WCEL
ADJG_CM_0008 ADJG Create/Modify If AdjgBandIndicator has the value 0, the full GSM band range 0~1023 is allowed; if AdjgBandIndicator has the value 1, only the GSM1900 band range is allowed.
ADJG BCCH ARFCN VALUE OUT OF RANGE
ADJG_CM_0009 ADJG Create/Modify When the ADJG is not GAN-specific, and the source WCEL is HSDPA enabled, the source cell’s HSDPAFmcgIdentifier must be defined
HSDPA FMCG MUST BE DEFINED IF HSDPA ENABLED AND ADJG(S) CREATED UNDER THE WCEL
ADJG_CM_0010 ADJG Create/Modify When the ADJG is not GAN-specific, the source WCEL is HSDPA-enabled, and HSDPA with AMR is enabled in the RNC, the source cell’s RTWithHSDPAFmcgIdentifier must be defined
RT HSDPA FMCG MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL
ADJG_CM_0011 ADJG Create/Modify If WireLessPriorityService in the RNC is Enabled, and ADJGId is 0, the value of AdjgSIB cannot be No, i,e, the ADJG must be included in System Information.
ADJGSIB IS NOT ENABLED FOR WPS ADJG IN ONE OR MORE WCEL IN RNC RNW DATABASE
ADJG_M_0001 ADJG Modify ADJG - BandIndicator is not modifiable
BAND INDICATOR MAY NOT BE CHANGED
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 3 ADJG consistency checking rules (Cont.)
12 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa66
ADJI consistency checking rules
5 ADJI consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
ADJI_C_0001 ADJI Create ADJIId must be unique within the parent WCEL
ADJI ALREADY CREATED UNDER WCEL
ADJI_C_0002 ADJI Create The maximum amount of ADJI under the WCEL is 48
MAXIMUM OF ADJIS FOR WCEL
ADJI_CM_0001 ADJI Create/Modify The maximum number of inter-frequency neighbour cells that can be included in the System Information is 32.
MAXIMUM NUMBER OF ADJIS INCLUDED IN BCCH INFOEXCEEDED
ADJI_CM_0002 ADJI Create/Modify ADJI – RtHopiIdentifier and NrtHopiIdentifier must refer to an existing HOPI object (Inter-system Handover Path)
HOPI NOT FOUND
ADJI_CM_0003 ADJI Create/Modify The UARFCN of the source WCEL and ADJI must be dif-ferent (WCEL – UARFCN, ADJI - AdjiUARFCN)
ADJI AND ITS SOURCE WCEL MUST HAVE DIFFER-ENT FREQS
ADJI_CM_0004 ADJI Create/Modify The scrambling code and UARFCN combination must be unique within the ADJI objects under the same source WCEL
PRI SCRC AND UARFCN COMBINATION OF AN INTER-FREQ NEIGHBOUR CELL MUST BE UNIQUE WITHIN ADJI
ADJI_CM_0005 ADJI Create/Modify ADJI with the same target WCEL must not exist
THERE IS ALREADY ANOTHER ADJ POINTING TO SAME TARGET UNDER THIS WCEL.
ADJI_CM_0006 ADJI Create/Modify The following parameters must be the same in ADJI and target WCEL: AdjiLAC, AdjiRAC, AdjiScrCode, AdjiTxPwr-RACH, AdjiTxPwrDPCH, AdjiCPICHTxPwr and Adji-UARFCN
PARAMETERS IN ADJ DEFI-NITION DO NOT MATCH WITH TARGET CELL
ADJI_CM_0007 ADJI Create/Modify RT+NRT FMCI must be defined for the source WCEL
FMCI ID NOT DEFINED FOR THE WCEL
ADJI_CM_0008 ADJI Create/Modify When the source WCEL is HSDPA-enabled, the source cell’s HSDPAFmciIdentifier must be defined
HSDPA FMCI MUST BE DEFINED IF HSDPA ENABLED AND ADJI(S) CREATED UNDER THE WCEL
Table 4 ADJI consistency checking rules
DN0934038Issue 01A
13
WCDMA RAN RNW consistency checking rules ADJI consistency checking rules
Id:0900d8058070fa66
ADJI_CM_0009 ADJI Create/Modify When the source WCEL is HSDPA enabled and HSDPA with AMR is enabled in the RNC, the source cell’s RTWithHSDPAFmciIdentifier must be defined
RT HSDPA FMCI MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL
ADJI_CM_0010 ADJI Create/Modify If the inter-frequency neighbor cell is controlled by the local RNC, ADJI-ADJITXDIV must be set to zero
IF THE INTER-FREQUENCY NEIGHBOR CELL IS CON-TROLLED BY THE LOCAL RNC, ADJI-ADJITXDIV MUST BE SET TO ZERO
ADJI_M_0001 ADJI Modify The parameters related to the target cell except AdjiRNCid (AdjiMCC, AdjiMNCLength, AdjiMNC, and AdjiCI) cannot be modified when the target cell is under the own RNC
TARGET CELL OF THE ADJACENCY IS NOT ALLOWED TO CHANGE IF TARGET CELL IS UNDER THE SAME RNC
ADJI_M_0002 ADJI Modify UARFCN cannot be modified when target cell is under own RNC
UARFCN MAY NOT BE CHANGED
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 4 ADJI consistency checking rules (Cont.)
14 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa68
ADJS consistency checking rules
6 ADJS consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
ADJS_C_0001 ADJS Create ADJSId must be unique within the parent WCEL
ADJS ALREADY CREATED UNDER WCEL
ADJS_C_0002 ADJS Create The maximum amount of ADJS under the WCEL is 31
MAXIMUM OF ADJSS FOR WCEL
ADJS_CM_0001 ADJS Create/Modify ADJS – RtHopsIdentifier and NrtHopsIdentifier must refer to the existing HOPS object (Intra-frequency Handover Path)
HOPS NOT FOUND
ADJS_CM_0002 ADJS Create/Modify The scrambling code must be different between the ADJS and the source WCEL
ADJS (INTRA-FREQ ADJ) AND SOURCE WCEL MUST HAVE DIFFERENT DL_PRI_SCR_CODE
ADJS_CM_0003 ADJS Create/Modify The same scrambling code is not allowed for other ADJS of the source WCEL
PRIMARY SCRAMBLING CODE OF AN INTRA-FRE-QUENCY NEIGHBOUR CELL MUST BE UNIQUE WITHIN ADJS.
ADJS_CM_0004 ADJS Create/Modify The same scrambling code is not allowed for any ADJD of the source WCEL
PRIMARY SCRAMBLING CODE OF AN ADJS AND AN ADJD OF THE SAME SOURCE WCEL MUST BE DIFFERENT
ADJS_CM_0005 ADJS Create/Modify ADJS must have unique target WCEL among ADJSs under the source WCEL
THE SAME TARGET CELL IS POINTED BY AN ADJS OF THE SAME SOURCE CELL
ADJS_CM_0006 ADJS Create/Modify ADJS must have different target WCEL from any ADJD under the source WCEL
THE SAME TARGET CELL IS POINTED BY AN ADJD OF THE SAME SOURCE CELL
ADJS_CM_0007 ADJS Create/Modify The following parameters must be the same in ADJS and the target WCEL: AdjsLAC, AdjsRAC, AdjsScrCode, AdjsTxPwrRACH and AdjsCPICHTxPwr
PARAMETERS IN ADJ DEFI-NITION DO NOT MATCH WITH TARGET CELL
ADJS_CM_008 ADJS Create/Modify If HSDPAHopsIdentifier is defined, the referred HOPS should exist
HOPS NOT FOUND
Table 5 ADJS consistency checking rules
DN0934038Issue 01A
15
WCDMA RAN RNW consistency checking rules ADJS consistency checking rules
Id:0900d8058070fa68
ADJS_CM_0009 ADJS Create/Modify When the source WCEL is HSDPA-enabled, HSDPAHop-sIdentifier must be defined
HSDPA HOPS MUST BE DEFINED IF HSDPA ENABLED FOR THE SOURCE WCEL
ADJS_CM_0010 ADJS Create/Modify ADJS – RtHopsIdentifier and NrtHopsIdentifier must refer to the existing HOPS object (Intra-frequency Handover Path)
HOPS NOT FOUND
ADJS_CM_0011 ADJS Create/Modify When the source WCEL is HSDPA-enabled ,and HSDPA with AMR is enabled in the RNC, RTWithHSDPAHopsI-dentifier must be defined
HSDPA HOPS FOR AMR MULTI-SERVICE MUST BE DEFINED FOR THE SOURCE WCEL
ADJS_CM_0012 ADJS Create/Modify If RTWithHSDPAHopsIdenti-fier is defined, the referred HOPS must exist
HOPS NOT FOUND
ADJS_CM_0013 ADJS Create/Modify If the intra-frequency neighbor cell is controlled by the local RNC, ADJS-AdjsTxDiv must be set to zero
If the intra-frequency neighbor cell is controlled by the local RNC, ADJS-AdjsTxDiv must be set to zero
ADJS_M_0001 ADJS Modify The parameters related to the target WCEL except AdjsRN-Cid (AdjsMCC, AdjsMNC-Length, AdjsMNC, and AdjsCI) cannot be modified when the target cell is under the same RNC
TARGET CELL OF THE ADJACENCY IS NOT ALLOWED TO CHANGE IF TARGET CELL IS UNDER THE SAME RNC
ADJS_CD_0001 ADJS Create/Delete UARFCN of the source and target WCEL must be the same
SOURCE AND TARGET WCELS MUST HAVE SAME FREQS IN ADJS (INTRA-FREQ ADJ)
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 5 ADJS consistency checking rules (Cont.)
16 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa6a
CMOB consistency checking rules
7 CMOB consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
CMOB_C_0001 CMOB Create It is not possible to create more than 2 CMOB objects whose parameter Restriction-GroupType is RNAR
CS DSAC CMOB COUNT TOO HIGH
CMOB_C_0002 CMOB Create It is not possible to create more than 4 CMOB objects whose parameter Restriction-GroupType is CS-DSAC
CS DSAC CMOB COUNT TOO HIGH
CMOB_C_0003 CMOB Create It is not possible to create more than 4 CMOB objects whose parameter Restriction-GroupType is PS-DSAC
PS DSAC CMOB COUNT TOO HIGH
CMOB_C_0004 CMOB Create A forced CMOB can't be created by the user
USER CANNOT CREATE OR DELETE FORCED TYPE CMOB OBJECT.
CMOB_M_0001 CMOB Modify The CMOB parameter ‘RestrictionGroupType’ cannot be changed
CMOB RESTRICTION TYPE CANNOT BE CHANGED.
CMOB_D_0001 CMOB Delete A CMOB can not be deleted if there are relations to it from WCEL objects
CMOB OBJECT CANNOT BE DELETED IF RELATED WCELS EXIST
CMOB_D_0002 CMOB Delete A forced CMOB can't be deleted by the user
USER CANNOT CREATE OR DELETE FORCED TYPE CMOB OBJECT.
Table 6 CMOB consistency checking rules
DN0934038Issue 01A
17
WCDMA RAN RNW consistency checking rules COCO consistency checking rules
Id:0900d8058070fa6c
8 COCO consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Object type Check description Error text
COCO_CM_001 COCO Create/Modify VP for each link should be found in the VPI list
VP ID OF COCO C-NBAP, D-NBAP, AAL2SIG, AAL2TP LINK SHOULD BE FOUND IN COCO VPI LIST.
COCO_CM_002 COCO Create/Modify "COCO PCR parameter checking: the sum of all VC’s PCR (PCR for CBR VCC and MDCR for UBR+ VCC) under one VP in COCO should not exceed the corresponding VP’s PCR or MDCR value"
SUM OF VCC PCR IS GREATER THAN VP PCR IN ONE COCO
COCO_CM_003 COCO Create/Modify VP already exists in COCO creation, the VP PCR value in COCO should not exceed the existed VP PCR value.
GIVEN VALUE IS TOO BIG
COCO_CM_004 COCO Create/Modify COCO TPI existence check: all ATM TP in the COCO should be found on the platform level
VCLTP DOES NOT EXIST VPLTP DOES NOT EXIST
COCO_CM_005 COCO Create/Modify CBR VCC cannot be config-ured under UBR+ VP in COCO object.
REQUESTED SERVICE CATEGORY FOR VCLTP IS NOT SUPPORTED IN THE VPCTP (FOR VCCS)
COCO_CM_006 COCO Create/Modify No unused ATM interface, VP in COCO object
UNUSED ATM IF OR VP IN COCO OBJECT.
COCO_CM_007 COCO Create/Modify Bundle usage in AAL2TP link should be found on the bundle list ( the related bundle item should be defined ).
BUNDLE ITEM IS MISSING IN COCO BUNDLE LIST
COCO_CM_008 COCO Create/Modify One AAL2 UP link should have one AAL2 signaling link asso-ciated
ILLEGAL AAL2 SIGNALING LINK RELATED TO COCO USER PLANE LINK.
COCO_CM_009 COCO Create/Modify The same AAL2 UP VCC should have the same signal-ing link
AAL2 SIGNALING LINK MISMATCH FOR COCO USER PLANE LINK.
COCO_CM_010 COCO Create/Modify The same AAL2 UP VCC should have the same path ID
AAL2 PATH ID MISMATCH
Table 7 COCO consistency checking rules
18 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa6c
COCO consistency checking rules
COCO_CM_011 COCO Create/Modify The AAL2 signaling link asso-ciated with AAL2 TP should be found on the AAL2SIG list
UNKNOWN SIGNALLING LINK ID
COCO_CM_012 COCO Create/Modify AAL2 user plane links with equal WAM ID must have the same A2EA
A2EA ADDRESS MISMATCH FOR COCO USER PLANE IN THE SAME WAM.
COCO_CM_013 COCO Create/Modify AAL2 user plane links with equal WAM ID have an equal AAL2 signaling link
AAL2 SIGNALING LINK MISMATCH FOR COCO USER PLANE IN THE SAME WAM.
COCO_CM_014 COCO Create/Modify WAM ID for AAL2TP link should be found on the D-NBAP TTP ID list
WAM ID AND CCP ID DO NOT MATCH
COCO_CM_015 COCO Create/Modify One AAL2SIG link cannot be used for different WAM
AAL2 SIGNALLING VCI IS USED BY AAL2 UPLINK
COCO_CM_016 COCO Create/Modify AAL2 UP usage should not overlap except when SHARED and DCH overlap is allowed
SHARED OR DEDICATED TRANSPORT SOLUTION SHOULD BE SELECTED FOR ALL AAL2 UP LINKS
COCO_CM_017 COCO Create/Modify The AAL2 path type for same AAL2UPUsage should be unique, it means that it, for example, is impossible to have stringent HSPA and stri-gentandstrigent bi-level HSPA in the same COCO
AAL2 PATH TYPES OF AN AAL2UPUSAGE ARE OVER-LAPPED
COCO_CM_018 COCO Create/Modify The AAL2 path type for HSPA VCC (AAL2UPUsage can be HSPA or DCHandHSPA) should be unique in one COCO.
AAL2 PATH TYPES OF AN AAL2UPUSAGE ARE OVER-LAPPED
COCO_CM_019 COCO Create/Modify "AAL2UPUsage and AAL2 path type combination: DCH: Stri, Sbi, StriandSbi; DCHandHSDPA: StriandSbi-andTol"
AAL2 UP USAGE AND AAL2 PATH TYPE COMBINATION IS ILLEGAL
COCO_CM_020 COCO Create/Modify All AAL2 UP links in same VCC have the same AAL2UPUsage
ALL AAL2 UP LINKS IN SAME VCC MUST HAVE SAME AAL2UPUSAGE VALUE
COCO_CM_021 COCO Create/Modify There can be no more than one HSDPA-dedicated VCC per route
ONLY ONE HSDPA VCC IS ALLOWED PER ROUTE
Checking rule identifier (ID)
Object type
Object type Check description Error text
Table 7 COCO consistency checking rules (Cont.)
DN0934038Issue 01A
19
WCDMA RAN RNW consistency checking rules COCO consistency checking rules
Id:0900d8058070fa6c
COCO_CM_022 COCO Create/Modify DCH stringent and DCH strin-gent bi-level should be included for each route
STRINGENT OR STRIN-GENT BI-LEVEL DCH IS MISSING FROM ROUTE STRINGENT OR STRIN-GENT BI-LEVEL DCH IS MISSING FROM ROUTE
COCO_CM_023 COCO Create/Modify There must be at least one SHARED VCC for per WBTS, this rule is dedicated for the poor man's route selection solution. In the poor man solu-tion, DCH + SHARED is allowed, one SHARED VCC is needed for the HSDPA traffic purpose
SHARED VCC IS MISSING FROM CONNECTION CON-FIGURATION OBJECT
COCO_CM_024 COCO Create/Modify At least one RT-DCH and NRT-DCH dedicated VCC per route
RT_DCH OR NRT_DCH DED-ICATED VCC IS MISSING FROM ROUTE
COCO_CM_025 COCO Create/Modify AAL2 UP links in same VCC must have the same AAL2 path type
AAL2 UP LINKS IN SAME VCC CANNOT HAVE DIF-FERENT PATHTYPE VALUES
COCO_CM_026 COCO Create/Modify Only service-category CBR for VPtp and control plane link and cbr or ubr+ for user plane VCLtp
ERROR IN SERVICE REQUEST
COCO_CM_027 COCO Create/Modify If the ingress category is UBRPLUS, MCR could not be larger than the corresponding PCR value
ERROR IN SERVICE REQUEST
COCO_CM_028 COCO Create/Modify If DynNRTDCHSchedPath-Switch is enabled, NRT VCC should be configured into COCO;
MISSING NRT VCC FOR DYNAMIC NRT PATH SELECTION
COCO_CM_030 COCO Create/Modify If bundle is used in one COCO, DynNRTDCHSchedPath-Switch should be ON.
BUNDLE USAGE DOES NOT MATCH FOR FLOW CONTROL METHOD
COCO_CM_031 COCO Create/Modify SHARED VCC can never be attached in a bundle
SHARED VCC CAN NEVER BE ATTACHED IN A BUNDLE
COCO_CM_032 COCO Create/Modify Tolerant DCH_RT, tolerant DCH_NRT, tolerant DCH cannot be in a bundle
PATH TYPE OF VCC ATTACHED IN A BUNDLE DOES NOT MATCH FOR BUNDLE USAGE
Checking rule identifier (ID)
Object type
Object type Check description Error text
Table 7 COCO consistency checking rules (Cont.)
20 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa6c
COCO consistency checking rules
COCO_CM_033 COCO Create/Modify In a bundle, NRT DCH VCC, HSDPA VCC, HSPA VCC and HSUPA VCC must be UBR+ type, and RTDCH and DCH VCCs can be either CBR or UBR+ type
SERVICE CATEGORY OF VCC ATTACHED IN A BUNDLE DOES NOT MATCH FOR BUNDLE USAGE
COCO_CM_034 COCO Create/Modify If the user has HSDPA dynamic flow control, a bundle is not used in COCO, and the user cannot modify CBR VCC to UBR+ for HSDPA/HSPA . The reason is that, in order for the HSDPA flow control to work with UBR+, the VCC should be in a bundle, and the DSHPATH and PS features are required. UBR+ can't be sold out as one seperate feature on top of RAS5.1. So the rule is to ensure that UBR+ and HSDYN is not a possible combination
UBR+ SERVICE CATEGORY CANNOT EXIST WITH HSDPA FLOW CONTROL IF BUNDLE IS NOT USED
COCO_CM_035 COCO Create/Modify All DCH (RTDCH, NRTDCH, DCH VCCs) should be in or out of the bundle, it is not allowed to have some DCH inside a bundle and others out of the bundle.
ALL DCH SHOULD BE INSIDE SAME BUNDLE OR OUTSIDE OF BUNDLE
COCO_CM_036 COCO Create/Modify The sum of the PCR (CBR) or the MDCR (UBR+) value of VCCeps inside the same bundle should not exceed the PCR value of the bundle
SUM OF PCR OR MCR OF NCIDS INSIDE BUNDLE EXCEEDS THE BUNDLE PCR
COCO_CM_037 COCO Create/Modify TPI consistency checking: 1) Same TPI should not be used by other COCO; 2) Same TPI can't be used in same COCO for C-NBAP, D-NBAP and AAL2SIG; 3) Only in same COCO and AAL2 multiplexing is used, AAL2TP can have same TPI
GIVEN VCI VALUE IS ALREADY IN USE
Checking rule identifier (ID)
Object type
Object type Check description Error text
Table 7 COCO consistency checking rules (Cont.)
DN0934038Issue 01A
21
WCDMA RAN RNW consistency checking rules COCO consistency checking rules
Id:0900d8058070fa6c
COCO_CM_038 COCO Create/Modify PATH ID consistency check-ing: 1) The same Path ID cannot be used in different COCO; 2) Only in the same COCO and AAL2 mux is enabled and same TPI, PATH ID can be the same.
AAL2 PATH ID MISMATCH
COCO_CM_039 COCO Create/Modify A2EA consistency checking: 1) The same A2EA address cannot be found in different COCO; 2) The same A2EA address cannot be found in dif-ferent WAM in the same COCO
COCO AAL2 ADDRESSES NOT UNIQUE
COCO_CM_040 COCO Create/Modify WAM ID cannot be changed for (1) AAL2 multiplexing is not used, and AAL2 path ID are not changed (2) AAL2 multi-plexing is used, and AAL2 path ID and A2EA address are not changed
THE PARAMETER CANNOT BE MODIFIED
COCO_CM_041 COCO Create/Modify There should be only one WAM ID defined for GenerateAAL2Num
NOT MORE THAN ONE DNBAPTP CAN BE DEFINED IF COCO-GENERATEAAL2NUM IS 3 (ONE A2EA FOR BTS).
COCO_CM_042 COCO Create/Modify Not more than two VCC can be allowed per WAM for UltraBTS if AAL2 multiplexing is not enabled
NOT MORE THAN TWO AAL2TP CAN BE DEFINED PER WAMID FOR ULTRA-SITE BTS IF COCO - AAL2MULTIPLEXING IS DIS-ABLED.
Checking rule identifier (ID)
Object type
Object type Check description Error text
Table 7 COCO consistency checking rules (Cont.)
22 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa6e
FMCG consistency checking rules
9 FMCG consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
FMCG_C_0001 FMCG Create FMCGId must be unique under the RNC
FMCG ALREADY CREATED
FMCG_CM_0001
FMCG Create/Modify The value of NcellSearchPe-riod must be lower than the value of MaxMeasPeriod
FMCG-GSMNCELLSEARCH-PERIOD MUST BE LOWER THAN FMCG-GSMMAX-MEASPERIOD
FMCG_M_0001 FMCG Modify If AMRDirReCell is modified to Enabled, the AdjgSIB parame-ter value of the outgoing GSM neighbor cell definition for Adjgld 0 cannot be No; this is true for all the WCELs that use the FMCG with RtFmcgIdenti-fier
ADJG-AdjgSIB SHOULD NOT BE SET AS 0 (NO) WHEN AMR CALL INTERSYSTEM HANDOVER IS ON
FMCG_D_0001 FMCG Delete FMCG object cannot be referred from any WCEL object
FMC STILL USED BY SOME WCEL
Table 8 FMCG consistency checking rules
DN0934038Issue 01A
23
WCDMA RAN RNW consistency checking rules FMCI consistency checking rules
Id:0900d8058070fa70
10 FMCI consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
FMCI_C_0001 FMCI Create FMCIId must be unique under the RNC
FMCI ALREADY CREATED
FMCI_CM_0001 FMCI Create/Modify The value of NcellSearchPe-riod must be lower than the value of MaxMeasPeriod
PARAMETER INTERDEPEN-DENCE ERROR
FMCI_D_0001 FMCI Delete FMCI object cannot be referred from any WCEL object
FMC STILL USED BY SOME WCEL
Table 9 FMCI consistency checking rules
24 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa72
FMCS consistency checking rules
11 FMCS consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
FMCS_C_0001 FMCS Create FMCSId must be unique under the RNC
FMCS ALREADY CREATED
FMCS_CM_0001 FMCS Create/Modify EDCHRemEcNoOffset should have at least 2 dB higher value than the defined inEDCHRe-mEcNoOffset to avoid frequent channel type switches between DCH and E-DCH.
CHECK FOR CPICH ECNO OFFSET E-DCH USAGE REMOVAL AND ALLOW E-DCH USAGE ECNO OFFSET ERROR
FMCS_CM_0002 FMCS Create/Modify EDCHRemEcNoOffset cannot get a value 0.5dB~1.5dB lower than the value defined in HSDPAServCellWindow
INTERDEPENDENCE BETWEEN EDCHREMEC-NOOFFSET AND HSD-PASERVCELLWINDOW ERROR
FMCS_CM_0003 FMCS Create/Modify HHoRscpThreshold should be lower than HHoRscpCancel
FMCS-HHORSCPCANCEL MUST BE HIGHER THAN FMCS-HHORSCPTHRESH-OLD
FMCS_CM_0004 FMCS Create/Modify FMCS- HHoEcNoThreshold must be lower than the value of FMCS- HhoEcNoCancel.
FMCS- HHOECNOTHRESH-OLD MUST BE LOWER THAN THE VALUE OF FMCS- HHOECNOCANCEL.
FMCS_D_0001 FMCS Delete The FMCS object cannot be referred from any WCEL object
FMC STILL USED BY SOME WCEL
Table 10 FMCS consistency checking rules
DN0934038Issue 01A
25
WCDMA RAN RNW consistency checking rules HOPG consistency checking rules
Id:0900d8058070fa74
12 HOPG consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
HOPG_D_0001 HOPG Delete HOPG object cannot be referred from any ADJG object
HOP IS USED BY SOME ADJ
Table 11 HOPG consistency checking rules
26 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa76
HOPI consistency checking rules
13 HOPI consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
HOPI_D_0001 HOPI Delete HOPI object cannot be referred from any ADJI object
HOP IS USED BY SOME ADJ
Table 12 HOPI consistency checking rules
DN0934038Issue 01A
27
WCDMA RAN RNW consistency checking rules HOPS consistency checking rules
Id:0900d8058070fa78
14 HOPS consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
HOPS_D_0001 HOPS Delete HOPS object cannot be referred from any ADJS object
HOP IS USED BY SOME ADJ
Table 13 HOPS consistency checking rules
28 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa7a
IPNB consistency checking rules
15 IPNB consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
IPNB_CM_001 IPNB Create/Modify CCPid defined for a DNBAP cannot be duplicate
DUPLICATE CCP IDS IN DNBAP LIST
IPNB_CM_002 IPNB Create/Modify At least one CCPid should be defined
NO DEFINED CCP ID
IPNB_CM_003 IPNB Create/Modify The SCTP port should not be out of range (65535)
INVALID DNBAP SCTP PORT
IPNB_CM_004 IPNB Create/Modify "SCTP port consistency check-ing: 1) The same SCTP port cannot be found in different IPNBs"
SCTP PORT NOT UNIQUE FOR ALL IPNBS.
IPNB_CM_005 IPNB Create/Modify "IP Address consistency checking: 1) The same IP Address cannot be found in dif-ferent IPNBs"
CONTROL PLANE DESTINA-TION IP ADDRESS CONFIG-URED IN IPNB HAS ALREADY BEEN USED
Table 14 IPNB consistency checking rules
DN0934038Issue 01A
29
WCDMA RAN RNW consistency checking rules IPQM consistency checking rules
Id:0900d8058070fa7c
16 IPQM consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
IPQM_D_0001 IPQM Delete IPQM cannot be deleted if there are relations to it from IU objects
IPQM ID IS IN USE
Table 15 IPQM consistency checking rules
30 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa7e
IU consistency checking rules
17 IU consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
IU_CM_0001 IU Create/Modify IU - GlobalCNId (Global CN Id) must be unique within all IUs
GLOBAL CN ID MUST BE UNIQUE
IU_CM_0002 IU Create/Modify If RAN sharing is not enabled, then the same IU - GlobalCNId - PLMNid - MNC (Mobile Network Code) must be defined for each Iu
DIFFERENT MNC FOR CN
IU_CM_0003 IU Create/Modify If MOCN/MORAN is ON, and Flex IU is not activated for some operator's CS or PS domain, then different PLMN must be defined for each IU item (separately inside CS items / separately inside PS items)
IF MOCN/MORAN IS ON THEN UNIQUE PLMN ID MUST BE DEFINED FOR EACH CN
IU_CM_0004 IU Create/Modify if MCN and RAN sharing options OFF, and IuFlex not in use,only one IU of each domain type is allowed
MAXIMUM NUMBER OF CS CN EXCEEDED MAXIMUM NUMBER OF PS CN EXCEEDED
IU_CM_0005 IU Create/Modify If the primary PLMNid is the same, the secondary plmn list definitions must also be the same
SECONDARY PLMN ID MUST BE UNIQUE UNDER A CERTAIN PRIMARY PLMN ID
IU_CM_0006 IU Create/Modify The primary PLMNid cannot be the same as one of the sec-ondary PLMNid
GLOBAL CN ID MUST BE UNIQUE
IU_CM_0007 IU Create/Modify NRIminforCSCN cannot be greater than NRImaxforCSCN, NRIminforPSCN cannot be greater than NRImaxforPSCN
NRIMINFORCSCN/PSCN CANNOT BE GREATER THAN NRIMAXFORC-SCN/PSCN
IU_CM_0008 IU Create/Modify At least one of the min/max pairs (NRIMaxforCSCN/NRIM-inforCSCN, NRIMaxforPSCN/ NRIMinforPSCN) cannot have 1023 (not used) value for all configured CN nodes of one operator whose corresponding NRI length is set to non-zero
IF NRILENGTHFORCS OR PSCN IS NONZERO,FOR EACH IU OBJ ATLEAST ONE OF THE MIN/MAX SHOULD INDICATE VALID RANGE.
Table 16 IU consistency checking rules
DN0934038Issue 01A
31
WCDMA RAN RNW consistency checking rules IU consistency checking rules
Id:0900d8058070fa7e
IU_CM_0009 IU Create/Modify If the FLexible IU feature is deactivated, the maximum number of defined CNs is 8
MAXIMUM NUMBER OF DEFINED DEFAULT CNS EXCEEDED
IU_CM_0010 IU Create/Modify Subnet_id cannot be defined if no IP addresses are given
SUBNET_ID CANNOT BE DEFINED WITHOUT IP ADDRESSES
IU_CM_0011 IU Create/Modify The IPQM must exist if it is defined in IU
IPQM NOT FOUND
IU_M_0001 IU Modify IU - GlobalCNId (Global CN Id) modification is prohibited
GLOBAL CN ID OF IU CANNOT BE MODIFIED
IU_M_0002 IU Modify The modification of an item of the secondary plmn list is denied if there are any WCEL(s) mapped to that item
OPERATION DENIED, SOME WCEL(S) CONNECTED TO CN (CORE NETWORK DEFI-NITION IN RNC)
IU_M_0003 IU Modify An IU object can't be modified if a configured IU primary or secondary PLMN causes a conflict with the RNC-CBC list
IU OBJECT CAN'T BE MODIFIED IF IU PRIMARY OR SECONDARY PLMN CONFIGURED CONFLICT WITH RNC-CBC LIST
IU_CD_0001 IU Create/Delete if IUCS doesn't exists, the user cannot define the IUPS core
PLMN ID MUST BE SAME FOR CS AND PS CN (CORE NETWORK)
IU_D_0001 IU Delete IU can not be removed if it is mapped to WCEL(s)
OPERATION DENIED, SOME WCEL(S) CONNECTED TO CN (CORE NETWORK DEFI-NITION IN RNC)
IU_D_0002 IU Delete An IU object cannot be deleted when IuState is other than BAR-US
IU OBJECT CAN NOT BE DELETED WHEN IUSTATE IS OTHER THAN BAR-US
IU_D_0003 IU Delete An IU Object cannot be deleted when IU Primary or Secondary PLMN is configured in the RNC-CBC list
IU OBJECT CAN'T BE DELETED IF IU PRIMARY OR SECONDARY PLMN CON-FIGURED IN RNC-CBC LIST.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 16 IU consistency checking rules (Cont.)
32 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa80
IUR consistency checking rules
18 IUR consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
IUR_CM_0001 IUR Create/Modify IURNRncId (Neighbour RNC identifier) and IUR - Neigh-bouringPLMNidList - Neigh-bouringPLMNid (Neighbouring PLMN identity) must be unique within all IUR
RNC ID + PLMN ID PAIR MUST BE UNIQUE WITHIN IUR LIST (NEIGHBOURING RNC LIST)
IUR_CM_0002 IUR Create/Modify Inside each IUR, the Neigh-bouringPLMNid (Neighbour-ing PLMN identity) must be unique.
PLMN IDS OF NEIGHBOUR-ING RNC MUST BE UNIQUE
IUR_CM_0003 IUR Create/Modify At least one Neighbouring-PLMNid must be defined for IUR
PLMN ID FOR NEIGHBOUR-ING RNC NOT DEFINED
IUR_CM_0004 IUR Create/Modify IUR - NRncSignPointCode (Signaling point code of neigh-bour RNC) and IUR - NRnc-NetworkInd (Network indicator of neighbour RNC) must be unique within all IUR in the DB
SIGNALLING POINT CODE MUST BE UNIQUE
Table 17 IUR consistency checking rules
DN0934038Issue 01A
33
WCDMA RAN RNW consistency checking rules RNC consistency checking rules
Id:0900d8058070fa82
19 RNC consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
RNC_CM_0001 RNC Create/Modify The value of the parameter HSDPAMinAllowedBitrateUl must be lower than or equal to the parameter HSDPAInitialBi-trateUl
HSDPAINITIALBITRATEUL MUST BE GREATER THAN OR EQUAL TO HSDPAMI-NALLOWEDBITRATEUL
RNC_CM_0002 RNC Create/Modify The value of the parameter SIB18 priority must not be higher than the value of the parameter SIB11/12 priority
PRIORITY OF SIB18 MUST NOT BE HIGHER THAN PRIORITY OF SIB11 OR SIB12
RNC_CM_0003 RNC Create/Modify EmergencyCallISHOSupport and IntelligentEmergencyCall-ISHOSupport are not allowed both tried to enable if emisho and iemisho options are sup-ported
ATTEMPTED TO ENABLE OPTIONS IEMISHO AND EMISHO SIMULTANEOUSLY
RNC_CM_0004 RNC Create/Modify The value of DelayThreshold-Min always has to be lower than the value of DelayThresh-oldMid, unless DelayThresh-oldMax has the value HSUPA CC mechanism disabled.
INTERDEPENDENCE BETWEEN DELAYTHRESH-OLDMIN, DELAYTHRESH-OLDMID AND DELAYTHRESHOLDMAX ERROR
RNC_CM_0005 RNC Create/Modify The value of DelayThreshold-Mid always has to be lower than the value of DelayThresh-oldMax, unless DelayThresh-oldMax has the value HSUPA CC mechanism disabled.
INTERDEPENDENCE BETWEEN DELAYTHRESH-OLDMIN, DELAYTHRESH-OLDMID AND DELAYTHRESHOLDMAX ERROR
RNC_CM_0006 RNC Create/Modify The AMRWithEDCH parame-ter is valid only if AMRWith-HSDSCH is enabled
AMRWITHEDCH IS VALID ONLY IF AMRWITHHSDSCH IS ENABLED
RNC_CM_0007 RNC Create/Modify The value of the parameter ThresholdMaxEDPDCHSR1920kbps must be higher than the value of the parameter ThresholdMaxEDPDCHSR960kbps
THRESHOLDMAXEDPDCHSR1920KBPS MUST BE GREATER THAN THRESHOLDMAXEDPDCHSR960KBPS
Table 18 RNC consistency checking rules
34 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa82
RNC consistency checking rules
RNC_CM_0008 RNC Create/Modify The value of DelayThresholdMid2msTTI always has to be lower than the value of DelayThresholdMax2msTTI
THE VALUE OF DELAYTHRESHOLDMID2MSTTI IS NOT LESS THAN THE VALUE OF DELAYTHRESHOLDMAX2MSTTI
RNC_CM_0009 RNC Create/Modify The value of DelayThresholdMin2msTTI always has to be lower than the value of DelayThresholdMid2msTTI
THE VALUE OF DELAYTHRESHOLDMIN2MSTTI IS NOT LESS THAN THE VALUE OF DELAYTHRESHOLDMID2MSTTI
RNC_CM_0010 RNC Create/Modify The value of ThresholdMaxEDPDCHSR3840kbps must be higher than the value of the parameter ThresholdMaxEDPDCHSR1920kbps
THE VALUE OF THRESHOLDMAXEDPDCHSR3840kbps IS NOT LARGER THAN VALUE OF THRESHOLDMAXEDPDCHSR1920kbps
RNC_CM_0011 RNC Create/Modify The value of PriForSRB-sOnHSPA must be greater than the values assigned to the parameters PriForStreamARP1, PriForStreamARP2 and PriForStreamARP3
PriForSRBsOnHSPA MUST BE BIGGER THAN PriForCon-vOnHSPA,PriForStreamARP1,PriForStreamARP2 AND PriForStreamARP3
RNC_CM_0012 RNC Create/Modify The initial bitrate for HSDPA UL DCH for NRT with stream-ing must be greater than or equal to the minimum allowed bitrate for HSDPA UL DCH for NRT with streaming.
INITIAL BR FOR HSDPA UL DCH FOR NRT WITH STREAMING CANNOT BE SAMLLER THAN MIN ALLOWED BR
RNC_CM_0013 RNC Create/Modify The value of FAST UE THRESHOLD must be greater than the value of FAST UE CANCEL
FAST UE THRESHOLD NOT GREATER THAN FAST UE CANCEL
RNC_CM_0014 RNC Create/Modify LCS Support for Anchoring can be enabled only when the parameter LCS Functionality is enabled
LCS Support for Anchoring can be enabled only when parameter LCS Functionality is enabled
RNC_CM_0015 RNC Create/Modify The value of PLMNID defined in IU operator list must be unique.
PLMNID IN IU OPERATOR LIST SHOULD BE UNIQUE
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 18 RNC consistency checking rules (Cont.)
DN0934038Issue 01A
35
WCDMA RAN RNW consistency checking rules RNC consistency checking rules
Id:0900d8058070fa82
RNC_CM_0016 RNC Create/Modify Priorities for streaming RABs must be greater than the priority of interactive signaling RABs.
PRIORITIES FOR STREAM-ING RABS MUST BE BIGGER THAN PRIORITY FOR INTERACTIVE SIGNALING RABS
RNC_CM_0017 RNC Create/Modify If RT over NRT is used for a specific ARP category, the priority set for interactive sig-naling RABs must be greater than the priority of thresholds RT over NRT
PRIORITIES FOR STREAM-ING RABS MUST BE BIGGER THAN PRIORITY FOR INTERACTIVE SIGNALING RABS
RNC_CM_0018 RNC Create/Modify The priority for interactive sig-naling RABs must be greater than the priorities of other inter-active and backgroud RABs.
PRIORITY FOR INTERAC-TIVE SIGNALING RABS MUST BE BIGGER THAN PRIORITIES FOR OTHER NRT RABS
RNC_CM_0019 RNC Create/Modify The priorities of HSPA NBR at uplink direction must form a continuous block of priorities used for NRTs.
PRIORITIES WITH NBR AT UL DIRECTION MUST COVER FROM THE HIGHEST PRIORITIES USED FOR NRTS
RNC_CM_0020 RNC Create/Modify The priorities with HSPA NBR at downlink direction must form a continuous block of priorities used for NRTs.
PRIORITIES WITH NBR AT DL DIRECTION MUST COVER FROM THE HIGHEST PRIORITIES USED FOR NRTS
RNC_CM_0021 RNC Create/Modify If RAN sharing is disabled, only one CBCItem can be defined.
MAXIMUM NUMBER OF CBC (CELL BROADCAST CENTER) EXCEEDED
RNC_CM_0022 RNC Create/Modify RNC - CBCList - CBCItem - CBCPLMNList - CBCPLMNId (CBC PLMN id) must be unique in the whole CBCList
PLMN IDS OF CBC (CELL BROADCAST CENTER) MUST BE UNIQUE
RNC_CM_0023 RNC Create/Modify If CBC is defined, at least one IP address must be defined
IP ADDRESS NOT DEFINED FOR CBC
RNC_CM_0024 RNC Create/Modify If the Service Area Broadcast option is not bought, CBC cannot be defined
SAB OPTION IS NOT IN USE IN RNC
RNC_CM_0025 RNC Create/Modify RAN sharing and IMSI HO are not supported, only one PLMN id is allowed for one CBC
MAXIMUM NUMBER OF PLMN IDS FOR CBC (CELL BROADCAST CENTER) EXCEEDED
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 18 RNC consistency checking rules (Cont.)
36 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa82
RNC consistency checking rules
RNC_CM_0026 RNC Create/Modify IU list must contain PLMN id defined for the CBC.
PLMN ID DEFINED FOR THE CBC (CELL BROADCAST CENTER) NOT FOUND IN CORE NETWORK DEFINI-TIONS
RNC_CM_0027 RNC Create/Modify RNC - DefaultAuthorisedNet-workId (Identifier of the Default Authorised Network) must point to the existing WANE object if the value is not 0.
WANE NOT FOUND
RNC_CM_0028 RNC Create/Modify The value of the parameter HSDPAMinAllowedBitrateUl must be lower than or equal to the parameter HSDPAInitialBi-trateUl
HSDPAINITIALBITRATEUL MUST BE GREATER THAN OR EQUAL TO HSDPAMI-NALLOWEDBITRATEUL
RNC_CM_0029 RNC Create/Modify If HSDPA16KBPSReturnChannel is Off, the 16 kbps value is not allowed for the following parameters: HSDPAminAl-lowedBitrateUL and HSD-PAinitialBitrateUL
HSDPA16KRETURNCHANNEL NOT ON
RNC_CM_0030 RNC Create/Modify HSDPAChaTypeSwitchWin-dow must have a smaller value than the value used in HSD-PAServCellWindow
HSDPACHATYPESWITCH-WINDOW NOT LESS THAN HSDPASERVCELLWINDOW
RNC_CM_0031 RNC Create/Modify RNC-Thresholdmaxedpdchsr3840Kbps must be higher than RNC-Thresholdmaxedpdchsr960Kbps.
RNC-THRESHOLDMAXEDPDCHSR3840KBPS MUST BE GREATER THAN RNC-THRESHOLDMAXEDPDCHSR960KBPS
RNC_CM_0032 RNC Create/Modify RNC-NullNRIForCSPool must be unique within RNC-IuOper-ator.
RNC-NullNRIForCSPool must be unique within RNC-IuOper-ator
RNC_CM_0033 RNC Create/Modify RNC-NullNRIForPSPool must be unique within RNC-IuOper-ator
RNC-NULLNRIFORPSPOOL MUST BE UNIQUE WITHIN RNC-IUOPERATOR
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 18 RNC consistency checking rules (Cont.)
DN0934038Issue 01A
37
WCDMA RAN RNW consistency checking rules RNC consistency checking rules
Id:0900d8058070fa82
RNC_CM_0034 RNC Create/Modify The value of the RNC-AMRLCRelatTXWindowRate1 should be lower than or equal to the value of the parameter RNC-AMRLCRelatTXWindowRate2
RNC-AMRLCRELATTXWINDOWRATE1 SHOULD BE SMALLER THAN OR EQUAL TO RNC-AMRLCRELATTXWINDOWRATE2
RNC_CM_0035 RNC Create/Modify The value of the RNC-AMRLCRelatTXWindowRate2 should be lower than or equal to the value of the parameter RNC-AMRLCRelatTXWindowRate3
RNC-AMRLCRELATTXWINDOWRATE2 SHOULD BE SMALLER THAN OR EQUAL TO RNC-AMRLCRELATTXWINDOWRATE3
RNC_CM_0036 RNC Create/Modify The value of the RNC-AMRLCRelatTXWindowRate3 should be lower than or equal to the value of the parameter RNC-AMRLCRelatTXWindowRate4
RNC-AMRLCRELATTXWINDOWRATE3 SHOULD BE SMALLER THAN OR EQUAL TO RNC-AMRLCRELATTXWINDOWRATE4
RNC_CM_0037 RNC Create/Modify The value of the RNC-AMRLCRelatTXWindowRate4 should be lower than or equal to the value of the parameter RNC-AMRLCRelatTXWindowRate5
RNC-AMRLCRELATTXWINDOWRATE4 SHOULD BE SMALLER THAN OR EQUAL TO RNC-AMRLCRELATTXWINDOWRATE5
RNC_CM_0038 RNC Create/Modify The value of the RNC-AMRLCRelatTXWindowRate5 should be lower than or equal to the value of the parameter RNC-AMRLCRelatTXWindowRate6
RNC-AMRLCRELATTXWINDOWRATE5 SHOULD BE SMALLER THAN OR EQUAL TO RNC-AMRLCRELATTXWINDOWRATE6
RNC_CM_0039 RNC Create/Modify The value of the RNC-AMRLCRelatTXWindowRate6 should be lower than or equal to the value of the parameter RNC-AMRLCRelatTXWindowRate7
RNC-AMRLCRELATTXWINDOWRATE6 SHOULD BE SMALLER THAN OR EQUAL TO RNC-AMRLCRELATTXWINDOWRATE7
RNC_CM_0040 RNC Create/Modify The value of the RNC-AMRLCRelatTXWindowRate7 should be lower than or equal to the value of the parameter RNC-AMRLCRelatTXWindowRate8
RNC-AMRLCRELATTXWINDOWRATE7 SHOULD BE SMALLER THAN OR EQUAL TO RNC-AMRLCRELATTXWINDOWRATE8
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 18 RNC consistency checking rules (Cont.)
38 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa82
RNC consistency checking rules
RNC_M_0001 RNC Modify RncId (RNC Identifier) is not modifiable
RNC IDENTIFIER MAY NOT BE CHANGED
RNC_M_0002 RNC Modify AMRwithHSDSCH is not allowed to be set to Enabled if the special value ‘Not defined’ is set to the parameter RTWith-HSDPAFmcsIdentifier or RTWithHSDPAFmciIdentifier, or RTWithHSDPAFmcgIdenti-fier, or RTWithHSDPAHopsI-dentifier, or AdjdRTWithHSDPAHopsId.
RT HSDPA FMCS IDENTI-FIER MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL RT HSDPA FMCI MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL RT HSDPA FMCG MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL HSDPA HOPS FOR AMR MULTI-SERVICE MUST BE DEFINED FOR THE OUTGOING ADJS OF THE WCEL RT HSDPA HOPS MUST BE DEFINED FOR ADJD OF HSDPA ENABLED CELL IF RNC SUPPORTS AMRWITH-HSDSCH
RNC_M_0003 RNC Modify If the Wireless Priority Service feature is enabled, then AdjgSIB is set to Enabled for every outgoing ADJG whose parameter ADJGid equals 0 of every WCEL
ADJGSIB IS NOT ENABLED FOR WPS ADJG IN ONE OR MORE WCEL IN RNC RNW DATABASE
RNC_M_0004 RNC Modify AMRwithEDCH is not allowed to be set to enabled if the special value ‘Not defined’ is set to the parameter RTWithH-SPAFmcsIdentifier.
HSPA FMCS IDENTIFIER FOR AMR MULTI-SERVICE NOT DEFINED
RNC_M_0005 RNC Modify When the Flexible Iu feature is activated, a maximum of 8 CN nodes can be configured as default CNs for routing
MAXIMUM NUMBER OF DEFINED DEFAULT CNS EXCEEDED
RNC_M_0006 RNC Modify HSDPA dynamic resource allocation cannot be disabled when HSDPA 14Mbps per user is enabled.
HSDPA 14MBPS PER USER CAN BE ENABLED ONLY IF HSDPA DYNAMIC RESOURCE ALLOCATION IS ENABLED
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 18 RNC consistency checking rules (Cont.)
DN0934038Issue 01A
39
WCDMA RAN RNW consistency checking rules RNC consistency checking rules
Id:0900d8058070fa82
RNC_M_0007 RNC Modify If the parameter HSPA QoS Enabled indicates that HSPA QoS is used for NRTs, or HSPA streaming is in use, HSDPA Dynamic Resource Allocation must be enabled.
HSPA QOS FOR NRT, HSPA STREAMING, CS VOICE OR HSPA STREAMING CS VOICE CAN BE USED IF HSDPA DYN RES ALLOC USED
RNC_M_0008 RNC Modify LCS Support for Anchoring can be enabled only when Operational Mode of LCS is RNC Centric Mode
LCS Support for Anchoring can be enabled only when Operational Mode of LCS is RNC Centric Mode
RNC_M_0009 RNC Modify PLMN ID defined in Global-CNID of IU item must be found in the IU operator list.
PLMN ID IN GLOBALCNID OF IU ITEM NOT FOUND IN IU OPERATOR LIST
RNC_M_0010 RNC Modify The CBC item or PLMN id cannot be removed from the CBC item if WCEL(s) with 3 SCCPCH (SAB activated) are mapped (same PLMN id) to it
SAME PLMN ID DEFINED FOR CBC (CELL BROAD-CAST CENTER) AND WCEL (SAB ACTIVATED)
RNC_M_0011 RNC Modify If the parameter HSDPADy-namicResourceAllocation is modified, all HSDPA wcels must be locked
OPERATION REQUIRES WCEL OBJECT TO BE LOCKED
RNC_M_0012 RNC Modify If HSDPADynamicRe-sourceAllocation changes to Enable, the rule PtxTarget >= PtxTargetPSMax >= PtxTar-getPSMin must be matched in all hsdpa WCELs
PTXTARGET LESS THAN PTXTARGETPS-MAX PARAMETER INTERDEPEN-DENCE ERROR
RNC_M_0013 RNC Modify If HSDPAServCellWindow is modified, FMCS- EDCHRe-mEcNoOffset cannot get a value which is 0.5dB~1.5dB lower than HSDPAServCell-Window.
INTERDEPENDENCE BETWEEN EDCHREMEC-NOOFFSET AND HSD-PASERVCELLWINDOW ERROR
RNC_M_0014 RNC Modify HSDPAMobility can be Disabled only when no cells are using HSUPA
HSUPAEnabled CAN BE ENABLED IF HSDPAMobility IS ENABLED;HSDPAMobility CAN BE DISABLED IF NO WCEL USE HSUPA
RNC_M_0015 RNC Modify WBTS-BroadcastSIB15 can not be enabled when the RNC-LCSFunctionality is not enabled.
WBTS-BROADCASTSIB15 CAN NOT BE USED WHEN RNC-LCSFUNCTIONALITY IS NOT ENABLED.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 18 RNC consistency checking rules (Cont.)
40 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa84
TQM consistency checking rules
20 TQM consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
TQM_D_0001 TQM Delete TQM cannot be deleted if there are relations to it from WBTS objects
The TQM is still used by some WBTSs
Table 19 TQM consistency checking rules
DN0934038Issue 01A
41
WCDMA RAN RNW consistency checking rules WANE consistency checking rules
Id:0900d8058070fa88
21 WANE consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
WANE_D_0001 WANE Delete A WANE object cannot be deleted if it is referred from WSG
THERE ARE WSG RELATED TO WANE
WANE_D_0002 WANE Delete A WANE object cannot be deleted if RNC - DefaultAutho-risedNetworkId refers to it
DEFAULT WANE CANNOT BE DELETED
Table 20 WANE consistency checking rules
42 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8a
WBTS consistency checking rules
22 WBTS consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
WBTS_C_0001 WBTS Create The maximum amount of WBTS objects is 2800 for RNC2600. As for RNC450/196, the default maximum is 384, and 512 or 600 if the corresponding options are bought.
MAXIMUM NUMBER OF WBTSS EXCEEDED
WBTS_C_0002 WBTS Create WBTSId must be unique under the RNC
WBTS ALREADY CREATED
WBTS_CM_0001 WBTS Create/Modify WBTS-SharedHSDPAFlow-ControlAllocation should be greater than or equal to the value of the WBTS-SharedHS-DPAallocation in the same WBTS.
SHAREDHSDPAALLOCA-TION GREATER THAN SHAREDHSDPAFLOWCON-TROLALLOCATION
WBTS_CM_0002 WBTS Create/Modify WBTS - ATMInterfaceID (ATM interface identifier) / VPI / VCI and WBTS - COCOId (Con-nection Configuration Identi-fier) references must be unique within all WBTS objects
COCO OBJECT IS BEING USED BY SOME WBTS
WBTS_CM_0003 WBTS Create/Modify WBTS - IPBasedRouteIdIub reference must be unique within all WBTS objects
THE IP BASED ROUTE ID NOT UNIQUE UNDER WBTS OBJECT.
WBTS_CM_0004 WBTS Create/Modify If the referred COCO object exists, then WBTS - COCOId and WBTS - ATMInterfaceID / VPI / VCI must be the same as given for COCO, if they are defined.
MISMATCH BETWEEN COCO ID AND C-NBAP PARAMS IN WBTS AND COCO-OBJECT
WBTS_CM_0005 WBTS Create/Modify When IubTransportMedia is not ATM, IP Subnet id must be defined
IUBTRANSPORTMEDIA IS NOT ATM, IPBASE-DROUTEIDIUB MUST BE DEFINED.
WBTS_CM_0006 WBTS Create/Modify WBTS- AutoConnSiteID must be unique for every BTS.
WBTS- AUTOCONNSITEID SHOULD BE UNIQUE FOR EVERY BTS.
Table 21 WBTS consistency checking rules
DN0934038Issue 01A
43
WCDMA RAN RNW consistency checking rules WBTS consistency checking rules
Id:0900d8058070fa8a
WBTS_CM_0007 WBTS Create/Modify WBTS- AutoConnHWID must be unique for every BTS.
WBTS- AUTOCONNHWID SHOULD BE UNIQUE FOR EVERY BTS.
WBTS_CM_0008 WBTS Create/Modify WBTS-BroadcastSIB15 cannot be enabled when the RNC-LCS functionality is not enabled.
WBTS-BROADCASTSIB15 CAN NOT BE USED WHEN RNC-LCSFUNCTIONALITY IS NOT ENABLED.
WBTS_CM_0009 WBTS Create/Modify WBTS-BroadcastSIB15 cannot be enabled when WSMLC-LCSInterfaceOption is not IUPC.
WBTS-BROADCASTSIB15 CAN NOT BE ENABLED WHEN WSMLC-LCSINTER-FACEOPTION IS NOT IUPC.
WBTS_CM_0010 WBTS Create/Modify WBTS-BroadcastSIB15.2 and WBTS-BroadcastSIB15.3 can be enabled only when WBTS-BroadcastSIB15 is enabled
WBTS-BROADCASTSIB15.2 OR WBTS-BROADCASTSIB15.3 CON-FLICTED WITH WBTS-BROADCASTSIB15.
WBTS_M_0001 WBTS Modify WBTS - ATMInterfaceID (ATM interface identifier) / VPI / VCI and WBTS - COCOId (Con-nection Configuration Identi-fier) modification requires WCEL object locking when the COCO is related to the WBTS
OPERATION REQUIRES THAT ALL WCELS UNDER THE WBTS MUST BE LOCKED
WBTS_M_0002 WBTS Modify DedicatedMeasReportPeriod or RRMULDCHActivityFactor or IubTransportMedia or Dedi-MeasRepPeriodCSdata or DediMeasRepPeriodPSdata requires WCEL object locking to all WCELS related to the WBTS if the WBTS is con-nected with COCO or IPNB
OPERATION REQUIRES THAT ALL WCELS UNDER THE WBTS MUST BE LOCKED
WBTS_M_0003 WBTS Modify IPNBId or IPBasedRouteIdIub requires WCEL object locking to all WCELS related to the WBTS, if the WBTS is con-nected with IPNB
OPERATION REQUIRES THAT ALL WCELS UNDER THE WBTS MUST BE LOCKED
WBTS_M_0004 WBTS Modify If IubTransportMedia is not ATM and WBTS is connected with COCO, IPBase-dRouteIdIub modification requires WCEL object locking.
OPERATION REQUIRES THAT ALL WCELS UNDER THE WBTS MUST BE LOCKED
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 21 WBTS consistency checking rules (Cont.)
44 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8a
WBTS consistency checking rules
WBTS_M_0005 WBTS Modify MaxNumberEDCHLCG must be higher than the value of the parameter WCEL-NumberED-CHReservedSHOBranchAddi-tions
NUMBEREDCHRESERVED-SHOBRANCHADDITIONS GREATER THAN MAXNUM-BEREDCHLCG OR MAX-NUMBEREDCHCELL
WBTS_M_0006 WBTS Modify NBAPCommMode is unmodifi-able.
NBAP COMMUNICATION MODE CANNOT BE MODIFIED
WBTS_M_0007 WBTS Modify The window size for interfer-ence measurement to start LHOs must be equal to or greater than Radio Resource Indication Period in WBTS cell
LHOWINSIZEONINTERFER-ENCE HAS TO BE EQUAL TO OR GREATER THAN RRINDPERIOD IN WBTS CELL
WBTS_M_0008 WBTS Modify WBTS-BTSFallbackEnabled modification requires object locking
OPERATION REQUIRES THAT ALL WCELS UNDER THE WBTS MUST BE LOCKED
WBTS_M_0009 WBTS Modify WBTS-IubTransportFallback-Enabled modification requires object locking
OPERATION REQUIRES THAT ALL WCELS UNDER THE WBTS MUST BE LOCKED
WBTS_M_0010 WBTS Modify The count of CCH Setup-enabled WCEL's cannot exceed the license CCHSetup capacity limit.
THE COUNT OF CCH SETUP ENABLED WCEL'S EXCEEDS THE LICENSE CCHSETUP CAPACITY LIMIT.
WBTS_M_0011 WBTS Modify WBTS-NBAPCommMode modification requires object locking
OPERATION REQUIRES THAT ALL WCELS UNDER THE WBTS MUST BE LOCKED
WBTS_D_0001 WBTS Delete The WBTS cannot be deleted if some WCELs are still under it.
IUBTRANSPORTMEDIA IS NOT ATM, IPBASE-DROUTEIDIUB MUST BE DEFINED.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 21 WBTS consistency checking rules (Cont.)
DN0934038Issue 01A
45
WCDMA RAN RNW consistency checking rules WCEL consistency checking rules
Id:0900d8058070fa8c
23 WCEL consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
WCEL_C_0001 WCEL Create WCEL - CId (Cell identifier) must be unique under the RNC
CELL IDENTIFIER IS NOT UNIQUE IN THE RNC
WCEL_C_0002 WCEL Create The maximum amount of WCEL objects in the RNW database for RNC196, RNC450 and RNC2600 is 1152, 1800 and 4800 respec-tively
MAXIMUM NUMBER OF WCELS EXCEEDED
WCEL_CM_0001 WCEL Create/Modify WCEL - EbNoSetIdentifier (Eb/No parameter set identi-fier) identifies the WRAB object
The WRAB object could not be found in the Radio Network Database.
WCEL_CM_0002 WCEL Create/Modify If WCEL - HspaMultiNrtRab-Support (HSPA multi NRT RAB Support) is enabledHSD-PAenabled (HSDPA enabled ) must be enabled
HSPA MULTI NRT RAB CAN BE ENABLED ONLY WHEN HSDPA IS ENABLED
WCEL_CM_0003 WCEL Create/Modify RtFmcsIdentifier and RtFmcsI-dentifier (RT/NRT FMCS Iden-tifier) must be defined.
FMCS NOT FOUND
WCEL_CM_0004 WCEL Create/Modify If RtFmciIdentifier (RT FMCI Identifier) is defined, NrtFmciI-dentifier (NRT FMCI Identifier) must be also defined.
IF RT FMCI IS GIVEN, ALSO NRT FMCI IS NEEDED
WCEL_CM_0005 WCEL Create/Modify If NrtFmciIdentifier (NRT FMCI Identifier) is defined, RtFmciI-dentifier (RT FMCI Identifier) must be also defined.
IF NRT FMCI IS GIVEN, ALSO RT FMCI IS NEEDED
WCEL_CM_0006 WCEL Create/Modify If ADJI is defined, RtFmciIden-tifier (RT FMCI Identifier) must also be defined.
FMCI ID NOT DEFINED FOR THE WCEL
WCEL_CM_0007 WCEL Create/Modify If RtFmcgIdentifier (RT FMCG Identifier) is defined, NrtFmcgI-dentifier (NRT FMCG Identi-fier) must also be defined.
IF RT FMCG IS GIVEN, ALSO NRT FMCG IS NEEDED
Table 22 WCEL consistency checking rules
46 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8c
WCEL consistency checking rules
WCEL_CM_0008 WCEL Create/Modify If NrtFmcgIdentifier (NRT FMCG Identifier) is defined, RtFmcgIdentifier (RT FMCG Identifier) must also be defined.
IF NRT FMCG IS GIVEN, ALSO RT FMCG IS NEEDED
WCEL_CM_0009 WCEL Create/Modify If ADJG is defined, RtFmcgI-dentifier (RT FMCG Identifier) must be defined.
FMCG ID NOT DEFINED FOR THE WCEL
WCEL_CM_0010 WCEL Create/Modify The value of FachLoadMargin-CCH must be lower than the value of FachLoadThreshold-CCH if both are not 0
WCEL-FACHLOADMARGIN-CCH MUST BE LESS THAN WCEL-FACHLOADTHRESH-OLDCCH
WCEL_CM_0011 WCEL Create/Modify The value of RachLoadMargin-CCH must be lower than the value of RachLoadThreshold-CCH if both are not 0
WCEL-RACHLOADMARGIN-CCH MUST BE LESS THAN WCEL-RACHLOAD-THRESHOLDCCH
WCEL_CM_0012 WCEL Create/Modify InitialBitRateDL should not be greater than the value of Max-BitRateDLPSNRT.
PARAMETER INTERDE-PENDENCE ERROR
WCEL_CM_0013 WCEL Create/Modify InitialBitRateDL should not be smaller than the value of MinAllowedBitRateDL.
PARAMETER INTERDE-PENDENCE ERROR
WCEL_CM_0014 WCEL Create/Modify InitialBitRateUL should not be greater than the value of Max-BitRateULPSNRT.
PARAMETER INTERDE-PENDENCE ERROR
WCEL_CM_0015 WCEL Create/Modify InitialBitRateUL should not be smaller than the value of MinAllowedBitRateUL.
PARAMETER INTERDE-PENDENCE ERROR
WCEL_CM_0016 WCEL Create/Modify MaxBitRateDLPSNRT should not be lower than the value of MinAllowedBitRateDL
PARAMETER INTERDE-PENDENCE ERROR
WCEL_CM_0017 WCEL Create/Modify MaxBitRateULPSNRT should not be lower than the value of MinAllowedBitRateUL
PARAMETER INTERDE-PENDENCE ERROR
WCEL_CM_0018 WCEL Create/Modify MinAllowedBitRateDL should not be greater than the value of MaxBitRateDLPSNRT
PARAMETER INTERDE-PENDENCE ERROR
WCEL_CM_0019 WCEL Create/Modify MinAllowedBitRateUL should not be greater than the value of MaxBitRateULPSNRT
PARAMETER INTERDE-PENDENCE ERROR
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
DN0934038Issue 01A
47
WCDMA RAN RNW consistency checking rules WCEL consistency checking rules
Id:0900d8058070fa8c
WCEL_CM_0020 WCEL Create/Modify The RACH_Tx_NB01max parameter value must always be higher than the value of the RACH_Tx_NB01min parame-ter
PARAMETER INTERDE-PENDENCE ERROR
WCEL_CM_0021 WCEL Create/Modify If the maximum cell range (CellRange) is greater than 10 km, AICH Transmission Timing is 1 and Rx Diversity Indicator is 1. If AICH Trans-mission Timing has the value 0, or if four antennas are used (Rx Diversity Indicator = 2), the maximum value can be 10 km.
CELL RANGE OF WCEL IS INCORRECT
WCEL_CM_0022 WCEL Create/Modify The value of LHOWinSizeON-Interference must be equal to or greater than RRIndPeriod if it is not 0 and NBAPCom-mMode is not NB/RSXXX
LHOWINSIZEONINTERFER-ENCE HAS TO BE EQUAL TO OR GREATER THAN RRINDPERIOD IN WBTS CELL
WCEL_CM_0023 WCEL Create/Modify The value of LHOWinSizeON-Interference should be equal to or greater than PrxTotalRe-portPeriod and PtxTotalRe-portPeriod if it is not 0 and NBAPCommMode is NB/RSXXX
LHOWINSIZEONINTERFER-ENCE CANNOT SHORTER THAN PRX AND PTXTOTAL-REPORTPERIOD IN NB/RSXXX CELL
WCEL_CM_0024 WCEL Create/Modify WCEL - UARFCN (UTRA Absolute Radio Frequency Channel Number) and WCEL PriScrCode (Primary downlink scrambling code) pair must be unique under the WBTS
WCELS UARFCN + DL_PRI_SCR_CODE PAIR MUST BE UNIQUE UNDER WBTS
WCEL_CM_0025 WCEL Create/Modify If WBTS-NBAPCommMode has value (NB/RSxxx), the value 1 of WCEL-AICHTra-Time must be used
If WBTS-NBAPCommMode has value (NB/RSxxx), the value 1 of WCEL-AICHTra-Time must be used
WCEL_CM_0026 WCEL Create/Modify If WBTS-NBAPCOMMMODE is set to ULTRASITE BTS / FLEXIBTS / PICOBTS, WCEL-CELLRANGE must not be set to zero
IF WBTS-NBAPCOM-MMODE IS SET TO ULTRA-SITE BTS / FLEXIBTS / PICOBTS, WCEL-CELL-RANGE MUST NOT BE SET TO ZERO
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
48 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8c
WCEL consistency checking rules
WCEL_CM_0027 WCEL Create/Modify WCELHSUPA2MSTTIEnabled can be enabled only when CDSPDH card is used in Upgraded Mode
WCEL-HSUPA2MSTTIENABLED CAN BE ENABLED ONLY WHEN CSDSP-DH CARD EXISTS
WCEL_CM_0028 WCEL Create/Modify WCEL - DirectedRRCEnabled and WCEL - DirectedRRC-ForHSDPALayerEnabled cannot be enabled simultane-ously If RNC - DirectedRRC-ForHSDPALayerEnhanc is disabled
PARAMETERS CANNOT BE BOTH ENABLED
WCEL_CM_0029 WCEL Create/Modify If WCEL - NbrOfSCCPCHs (Number of SCCPCHs) is 3 (the SAB feature is active), SACB (Service Area Code for SAB) must be defined.
SAC_B MUST BE DEFINED IF SAB ACTIVE
WCEL_CM_0030 WCEL Create/Modify If WCEL - NbrOfSCCPCHs (Number of SCCPCHs) is 3 (the SAB feature is active), CTCHCapaHighPri must be defined.
CTCH_CAPA_CBS_MSG MUST BE DEFINED IF SAB ACTIVE
WCEL_CM_0031 WCEL Create/Modify If WCEL - NbrOfSCCPCHs (Number of SCCPCHs) is 3 (the SAB feature is active), KforCTCH must be defined.
K_CTCH MUST BE DEFINED IF SAB ACTIVE
WCEL_CM_0032 WCEL Create/Modify If WCEL - NbrOfSCCPCHs (Number of SCCPCHs) is 3 (the SAB feature is active), NforCTCH must be defined.
N_CTCH MUST BE DEFINED IF SAB ACTIVE
WCEL_CM_0033 WCEL Create/Modify If WCEL - NbrOfSCCPCHs (Number of SCCPCHs) is 3 (the SAB feature is active), RNC - CBCList - CBCItem (CBC Item) must be defined
CBC (CELL BROADCAST CENTER) MUST BE DEFINED IF SAB (SERVICE AREA BROADCAST) IN USE
WCEL_CM_0034 WCEL Create/Modify WCEL - SACB (Service Area Code for SAB) must be unique in the RNC
SAC_B PARAMETER MUST BE UNIQUE IN RNC
WCEL_CM_0035 WCEL Create/Modify SectorID: Two (or more) cells can belong to the same sector if DirectedRRCForHSDPALay-erEnhanc is enabled
If DirectedRRCForHSDPA-LayerEnhanc is disabled, there cannot be more than two layers
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
DN0934038Issue 01A
49
WCDMA RAN RNW consistency checking rules WCEL consistency checking rules
Id:0900d8058070fa8c
WCEL_CM_0036 WCEL Create/Modify SectorID: if two (or more) cells belong to the same sector, the following parameters should be the same: The target for total transmitted power (Ptx-Target), The offset for trans-mitted power (PtxOffset), The target for received power (Prx-Target), The offset for received power (PrxOffset), Mobile Country Code (MCC), Mobile Network Code (MNC)
ILLEGAL SECTOR ID FOR WCEL UNDER THIS WBTS
WCEL_CM_0037 WCEL Create/Modify A WCEL object cannot be created or modified with a relation to a CMOB that does not exist. The relation of WCEL to CMOB is defined with the parameters 'RNARGroupId', 'CSGroupId' and 'PSGroupId'.
CMOB NOT FOUND
WCEL_CM_0038 WCEL Create/Modify The WCEL parameter RNAR-GroupId can contain only either the value Not defined or an identifier for CMOB whose type is RNAR
CMOB TYPE AND USAGE DO NOT MATCH IN WCEL
WCEL_CM_0039 WCEL Create/Modify WCEL parameter CSGroupId can contain only either the value Not defined or an identi-fier for CMOB whose type is CS-DSAC
CMOB TYPE AND USAGE DO NOT MATCH IN WCEL
WCEL_CM_0040 WCEL Create/Modify WCEL parameter PSGroupId can contain only either the value Not defined or an identi-fier for CMOB whose type is PS-DSAC
CMOB TYPE AND USAGE DO NOT MATCH IN WCEL
WCEL_CM_0041 WCEL Create/Modify AMRUnderTxTotal must be lower than AMRTargetTxTotal
AMRUNDERTXTOTAL MUST BE SMALLER THAN AMRTARGETTXTOTAL
WCEL_CM_0042 WCEL Create/Modify AMRTargetTXtotal must be lower than AMROverTxtotal
AMRTARGETTXTOTAL MUST BE SMALLER THAN AMROVERTXTOTAL
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
50 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8c
WCEL consistency checking rules
WCEL_CM_0043 WCEL Create/Modify AMRUnderTxTotal must be lower than AMRUnderTxTotal
WCEL-AMROVERTXTOTAL MUST BE GREATER THAN WCEL-AMRUNDERTXTO-TAL
WCEL_CM_0044 WCEL Create/Modify AMRUnderTxNC must be lower than AMRTargetTxNC
AMRUNDERTXNC MUST BE SMALLER THAN AMRTAR-GETTXNC
WCEL_CM_0045 WCEL Create/Modify AMRTargetTxNC must be lower than AMROverTxNC
AMRTARGETTXNC MUST BE SMALLER THAN AMROVERTXNC
WCEL_CM_0046 WCEL Create/Modify AMRUnderTxNC must be lower than AMROverTxNC
WCEL-AMRUNDERTXNC MUST BE SMALLER THAN WCEL-AMROVERTXNC.
WCEL_CM_0047 WCEL Create/Modify AMRUnderTxNonHSPA must be lower than AMRTargetTx-NonHSPA
AMRUNDERTXNONHSPA MUST BE SMALLER THAN AMRTARGETTXNONHSPA
WCEL_CM_0048 WCEL Create/Modify AMRTargetTxNonHSPA must be lower than AMROverTx-NonHSPA
AMRTARGETTXNONHSPA MUST BE SMALLER THAN AMROVERTXNONHSPA
WCEL_CM_0049 WCEL Create/Modify AMRUnderTxNonHSPA must be lower than AMROverTx-NonHSPA
WCEL-AMROVERTX-NONHSPA MUST BE GREATER THAN WCEL-AMRUNDERTXNONHSPA
WCEL_CM_0050 WCEL Create/Modify AMRUnderSC must be lower than AMRTargetSC
AMRUNDERSC MUST BE SMALLER THAN AMRTAR-GETSC
WCEL_CM_0051 WCEL Create/Modify AMRTargetSC must be lower than AMROverSC
AMRTARGETSC MUST BE SMALLER THAN AMROVERSC
WCEL_CM_0052 WCEL Create/Modify AMRUnderSC must be lower than AMROverSC
WCEL-AMROVERSC MUST BE GREATER THAN WCEL-AMRUNDERSC
WCEL_CM_0053 WCEL Create/Modify AMRUnderTransmission must be lower than AMRTar-getTransmission
AMRUNDERTRANSMIS-SION MUST BE SMALLER THAN AMRTARGETTRANS-MISSION
WCEL_CM_0054 WCEL Create/Modify AMRTargetTransmission must be lower than AMROverTrans-mission
AMRTARGETTRANSMIS-SION MUST BE SMALLER THAN AMROVERTRANS-MISSION
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
DN0934038Issue 01A
51
WCDMA RAN RNW consistency checking rules WCEL consistency checking rules
Id:0900d8058070fa8c
WCEL_CM_0055 WCEL Create/Modify AMRUnderTransmission must be lower than AMROverTrans-mission
WCEL-AMROVERTRANS-MISSION MUST BE GREATER THAN WCEL-AMRUNDERTRANSMIS-SION
WCEL_CM_0056 WCEL Create/Modify PtxCellMax must be greater than or equal to PtxMaxHS-DPA
WCEL-PTXCELLMAX MUST BE GREATER THAN OR EQUAL TO WCEL-PTX-MAXHSDPA
WCEL_CM_0057 WCEL Create/Modify RachTxNb01Max must be greater than or equal to RachTxNb01Min
WCEL-RACH_TX_NB01MIN PARAMETER VALUE MUST BE LOWER THAN THE VALUE OF WCEL-RACH_TX_NB01MAX PARAMETER
WCEL_CM_0058 WCEL Create/Modify PtxTargetPSMax must be greater than or equal to Ptx-TargetPSMin
WCEL- PTXTARGETPSMAX MUST BE GREATER THAN OR EQUAL TO THE WCEL- PTXTARGETPSMIN
WCEL_CM_0059 WCEL Create/Modify PtxFDPCHMax must not be greater than PtxFDPCHMin
WCEL-PTXFDPCHMAX PARAMETER MUST NOT BE GREATER THAN WCEL-PTXFDPCHMIN PARAME-TER
WCEL_CM_0060 WCEL Create/Modify FDPCHEnabled can be Enabled only if HSUPAEn-abled is Enabled
FDPCHEnabled CAN BE ENABLED ONLY IF HSU-PAEnable IS ENABLED
WCEL_CM_0061 WCEL Create/Modify FDPCHEnabled can be Enabled only if HSPAQoSEn-abled value is 1 or higher
FDPCHEnabled CAN BE ENABLED ONLY IF QoS pri-oritization is used with param-eter HSPAQoSEnabled
WCEL_CM_0062 WCEL Create/Modify HSUPAEnabled can be Enabled only when HSDPA-Mobility is Enabled
HSUPAEnabled CAN BE ENABLED IF HSDPAMobility IS ENABLED;HSDPAMobility CAN BE DISABLED IF NO WCEL USE HSUPA
WCEL_CM_0063 WCEL Create/Modify If the HSDPA-enabled param-eter value is Enabled, WCELP-SCNId (PS CN Id) must be given
PS CN ID MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
52 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8c
WCEL consistency checking rules
WCEL_CM_0064 WCEL Create/Modify If the HSDPA-enabled param-eter value is Enabled, HSD-PAFmcsIdentifier must be defined
HSDPA FMCS MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL
WCEL_CM_0065 WCEL Create/Modify If HSDPA enabled parameter value is enabled and AMR-WithHSDSCH is enabled, RTWithHSDPAFmcsIdentifier must be defined.
RT HSDPA FMCS IDENTI-FIER MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL
WCEL_CM_0066 WCEL Create/Modify if HSDPA and HSDPA Dynamic Resource Allocation are Enabled, PtxTargetPSMax must be lower than or equal to the PtxTarget.
PARAMETER INTERDE-PENDENCE ERROR
WCEL_CM_0067 WCEL Create/Modify if HSDPA and HSDPA Dynamic Resource Allocation are Enabled, PtxTargetPSMax must be greater than or equal to the PtxTargetPSMin.
PARAMETER INTERDE-PENDENCE ERROR
WCEL_CM_0068 WCEL Create/Modify If the HSDPA enabled parame-ter value is Enabled, PtxTar-getHSDPA must be defined
PARAMETER PTX_TARGET_HSDPA MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL
WCEL_CM_0069 WCEL Create/Modify If the HSDPA enabled parame-ter value is Enabled, Ptx-MaxHSDPA must be defined
PARAMETER PTX_MAX_HSDPA MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL
WCEL_CM_0070 WCEL Create/Modify If the HSDPA enabled parame-ter value is Enabled, PtxOff-setHSDPA must be defined
PARAMETER PTX_OFFSET_HSDPA MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL
WCEL_CM_0071 WCEL Create/Modify If WCEL - HSDPA64UsersEnabled (HSDPA 64 users enabled ) is Enabled, HSDPAenabled (HSDPA enabled ) must be Enabled
HSDPA 64 USERS ENABLED CAN BE ENABLED ONLY WHEN HSDPA ENABLED IS ENABLED.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
DN0934038Issue 01A
53
WCDMA RAN RNW consistency checking rules WCEL consistency checking rules
Id:0900d8058070fa8c
WCEL_CM_0072 WCEL Create/Modify The following HSDPA 64 user feature related parameters request object locking when modified: . HSDPA64UsersEnabled
OPERATION REQUIRES WCEL OBJECT TO BE LOCKED
WCEL_CM_0073 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, HSD-PAEnabled must be Enabled
INTERDEPENDENCE BETWEEN HSUPA ENABLED AND HSDPA ENABLED ERROR
WCEL_CM_0074 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) and AMRWith-HSDSCH are enabled, RTWithHSDPAFmcsIdentifier must be defined,
HSPA FMCS IDENTIFIER FOR AMR MULTI-SERVICE NOT DEFINED
WCEL_CM_0075 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, HSDPA-DynamicResourceAllocation must be Enabled
HSDPA DYNAMIC RESOURCE ALLOCATION NOT ENABLED
WCEL_CM_0076 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, the HSU-PAXUSERSENABLED value Disabled is not allowed
HSUPA ENABLED CANNOT BE ENABLED IF HSUPA X USERS ENABLED IS NOT ENABLED.
WCEL_CM_0077 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, HSD-PAFmcsIdentifier must be defined
HSPA FMCS IDENTIFIER NOT DEFINED
WCEL_CM_0078 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, PrxTar-getPSMax must be lower than or equal to the PrxTarget.
PRXTARGET LESS THAN PRXTARGETPSMAX
WCEL_CM_0079 WCEL Create/Modify PrxLoadMarginEDCH must be lower than or equal to the value of the PrxMaxTargetBTS
INTERFERENCE MARGIN FOR MIN EDCH LOAD GREATER THAN MAX TARGET RECEIVED WIDE BAND POWER
WCEL_CM_0080 WCEL Create/Modify PrxTargetPSMax must be greater than or equal to Prx-TargetPSMin.
MIN PS TARGET INTER-FERENCE SHARING BIGGER THAN MAX PS TARGET INTERFERENCE SHARING
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
54 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8c
WCEL consistency checking rules
WCEL_CM_0081 WCEL Create/Modify PrxLoadMarginDCH must be lower than or equal to the value of PrxLoadMarginMaxDCH.
INTERFERENCE MARGIN FOR THE MIN UL DCH LOAD GREATER THAN THE MAX VALUE
WCEL_CM_0082 WCEL Create/Modify The value of NumberED-CHReservedSHOBranchAddi-tions must be lower than the values of MaxNumberEDCH-Cell and MaxNumberED-CHLCG
NUMBEREDCHRESERVED-SHOBRANCHADDITIONS GREATER THAN MAXNUM-BEREDCHLCG OR MAX-NUMBEREDCHCELL
WCEL_CM_0083 WCEL Create/Modify If HSUPAEnabled (HSUPA enabled) is Enabled, Num-berEDCHReservedSHO-BranchAdditions must be lower than the value of HSU-PAXUsersEnabled.
IF HSUPA IS ENABLED, NUMBEREDCHRESERVED-SHOBRANCHADDITIONS MUST BE LOWER THAN HSUPAXUSERSENABLED
WCEL_CM_0084 WCEL Create/Modify If HSUPA is activated, it must be activated in all cells that use the same frequency (UARFCN) in the same BTS.
THE HSUPA STATE OF WCELS WITH SAME UARFCN INCONSISTENCY
WCEL_CM_0085 WCEL Create/Modify If HSUPA is deactivated, it must be deactivated in all cells that use the same frequency (UARFCN) in the same BTS.
THE HSUPA STATE OF WCELS WITH SAME UARFCN INCONSISTENCY
WCEL_CM_0086 WCEL Create/Modify The following HSUPA feature related parameters request object locking when modified: HSUPAEnabled, PrxLoadMar-ginEDCH, SIRDPCCHOffset-EDPCH, MaxTotalUplinkSymbolRate, TargetNSEDCHToTotalED-CHPR
OPERATION REQUIRES WCEL OBJECT TO BE LOCKED
WCEL_CM_0087 WCEL Create/Modify HSUPA2MSTTIEnabled can be set to Enabled only if HSUPA is enabled in the cell using the RNP parameter HSUPAEnabled
HSUPA2MSTTIEnabled CAN BE SET TO ENABLED ONLY IF HSUPAEnabled IS ENABLED
WCEL_CM_0088 WCEL Create/Modify MaxTotalUplinkSymbolRate can be set to 3 (5760kbps, 2*SF2+2*SF4) only if HSUPA 2ms TTI is enabled in the cell using the RNP parameter
MaxTotalUplinkSymbolRate CAN BE SET TO 5760kbps ONLY IF HSUPA2MSTTIEnabled IS ENABLED
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
DN0934038Issue 01A
55
WCDMA RAN RNW consistency checking rules WCEL consistency checking rules
Id:0900d8058070fa8c
WCEL_CM_0089 WCEL Create/Modify If the value of HSPAQoSEn-abled is 1 (QoS prioritization for HSPA NRT connections) or 2(HSPA streaming is in use), HSDPAEnabled must be Enabled
HSPA QOS FOR NRT, HSPA STREAMING, CS VOICE OR HSPA STREAMING CS VOICE CAN BE USED ONLY WHEN HSDPA IS ENABLED
WCEL_CM_0090 WCEL Create/Modify If the value of HSPAQoSEn-abled is 1(QoS prioritization for HSPA NRT connections) or 2(HSPA streaming is in use), HSDPADynamicResourceAl-location must be Enabled
HSPA QOS FOR NRT, HSPA STREAMING, CS VOICE OR HSPA STREAMING CS VOICE CAN BE USED IF HSDPA DYN RES ALLOC USED
WCEL_CM_0091 WCEL Create/Modify If the value of HSPAQoSEn-abled is 2 ( HSPA streaming is in use), NBAPCommmode should not have the value 1 (NB/RSxxx)
HSPA QOS FOR NRT, HSPA STREAMING, CS VOICE OR HSPA STREAMING CS VOICE CAN BE USED IF HSDPA DYN RES ALLOC USED
WCEL_CM_0092 WCEL Create/Modify The following HSPA QoS and Streaming feature related parameters request object locking when modified: HSPAQoSEnabled
OPERATION REQUIRES WCEL OBJECT TO BE LOCKED
WCEL_CM_0093 WCEL Create/Modify WCEL and Intra-Frequency neighbouring WCEL must have different scrambling codes (PriScrCode) and the same frequency (uarfcn)
SOURCE AND TARGET WCELS MUST HAVE DIF-FERENT DL_PRI_SCR_CODE IN ADJS (INTRA-FREQ ADJ) SOURCE AND TARGET WCELS MUST HAVE SAME FREQS IN ADJS (INTRA-FREQ ADJ)
WCEL_CM_0094 WCEL Create/Modify WCEL and additional intra-fre-quency adjacency WCEL must have different scrambling codes (PriScrCode) and the same frequency (uarfcn)
SOURCE AND TARGET CELLS MUST HAVE DIF-FERENT PRIMARY SCRAM-BLING CODE IN ADJD SOURCE AND TARGET CELLS MUST HAVE SAME FREQUENCY IN ADJD
WCEL_CM_0095 WCEL Create/Modify WCEL and Inter-frequency neighbouring WCEL must have different frequencies
SOURCE AND TARGET WCELS MUST HAVE DIF-FERENT FREQS IN ADJI (INTER-FREQ ADJ)
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
56 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8c
WCEL consistency checking rules
WCEL_CM_096 WCEL Create/Modify WCEL and incoming intra-fre-quency adjacency (ADJS) must have the same scram-bling code (PriScrCode).
PRIMARY SCRAMBLING CODE MUST BE SAME FOR THE WCEL AND THE INCOMING ADJACENCY (ADJS)
WCEL_CM_097 WCEL Create/Modify Primary Scrambling Code of an intra-frequency neighbour cell must be unique within the basic and additional intra-fre-quency neighbour cells.
PRIMARY SCRAMBLING CODE OF AN INTRA-FRE-QUENCY NEIGHBOUR CELL MUST BE UNIQUE WITHIN ADJS. PRIMARY SCRAMBLING CODE MUST BE UNIQUE WITHIN ADJD OF THE SAME SOURCE CELL
WCEL_CM_098 WCEL Create/Modify Primary Scrambling Code of an additional intra-frequency neighbour cell must be unique within the basic and additional intra-frequency neighbour cells.
PRIMARY SCRAMBLING CODE OF AN ADJS AND AN ADJD OF THE SAME SOURCE WCEL MUST BE DIFFER-ENT PRIMARY SCRAMBLING CODE MUST BE UNIQUE WITHIN ADJD OF THE SAME SOURCE CELL
WCEL_CM_099 WCEL Create/Modify Primary Scrambling Code and the UTRA RF Channel Number combination of an inter-frequency neighbour cell must be unique within inter-fre-quency neighbour cells.
PRI SCRC AND UARFCN COMBINATION OF AN INTER-FREQ NEIGHBOUR CELL MUST BE UNIQUE WITHIN ADJI
WCEL_CM_0100 WCEL Create/Modify If WCEL-HSPA72UsersPerCell is set to Enabled ,WCEL-HSUPAEN-ABLED must be Enabled
WCEL-HSPA72USERSPERCELL CAN BE ENABLED ONLY WHEN PARAMETER WCEL-HSUPAENABLED IS ENABLED.
WCEL_CM_0101 WCEL Create/Modify if WCEL-HSDPAMAXBITRA-TEUL is set to Enabled, RNC-HSDPA16KBPSRETURNCHANNEL must be Enabled.
VALUE OF WCEL-HSDPA-MAXBITRATEUL CAN BE 16KBPS ONLY WHEN RNC-HSDPA16KBPSRETURNCHANNEL IS ENABLED.
WCEL_CM_0102 WCEL Create/Modify WCEL-URAId must be unique within WCEL-URAIdList.
WCEL-URAID MUST BE UNIQUE WITHIN WCEL-URAIIDLIST.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
DN0934038Issue 01A
57
WCDMA RAN RNW consistency checking rules WCEL consistency checking rules
Id:0900d8058070fa8c
WCEL_CM_0103 WCEL Create/Modify The value of WCEL-NbrofSC-CPCHs cannot be one if WCEL-PCH24kbpsEnable is Enabled.
WCEL-NBROFSCCPCHS CAN NOT BE ONE IF WCEL-PCH24KBPSENABLE IS ENABLED.
WCEL_CM_0104 WCEL Create/Modify The value of WCEL-AMRUnderTxNC must be lower than the value of WCEL-AMROverTxNC.
WCEL-AMRUNDERTXNC MUST BE SMALLER THAN WCEL-AMROVERTXNC.
WCEL_M_0001 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, no outgoing ADJS cells HSDPA-HopsIdentifier value is allowed to be ‘not defined’
HSDPA HOPS MUST BE DEFINED FOR OUTGOING ADJS OF THE WCEL
WCEL_M_0002 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, and AMRWithHSDSCH is Enabled, the "no outgoing ADJS cells" RTWithHSDPAHopsIdentifier value is not allowed to be ‘not defined’
HSDPA HOPS FOR AMR MULTI-SERVICE MUST BE DEFINED FOR THE OUTGOING ADJS OF THE WCEL
WCEL_M_0003 WCEL Modify If HSDPA enabled parameter value is enabled, no outgoing ADJD cells HSDPAHopsIden-tifier value is allowed to be ‘not defined’
HSDPA HOPS ID MUST BE DEFINED FOR OUTGOING ADJD OF HSDPA ENABLED CELL
WCEL_M_0004 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, and AMRWithHSDSCH is Enabled, the "no outgoing ADJD cells" RTWithHSDPAHopsIdentifier value is not allowed to be ‘not defined’
HSDPA HOPS ID MUST BE DEFINED FOR OUTGOING ADJD OF HSDPA ENABLED CELL
WCEL_M_0005 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, and ADJI is defined, the HSDPAF-mciIdentifier is not allowed to be ‘not defined’
HSDPA FMCI MUST BE DEFINED IF HSDPA ENABLED AND ADJI(S) CREATED UNDER THE WCEL
WCEL_M_0006 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, AMR-WithHSDSCH is Enabled and ADJI is defined, the RTWith-HSDPAFmcsIdentifier is not allowed to be ‘not defined’
RT HSDPA FMCI MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
58 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8c
WCEL consistency checking rules
WCEL_M_0007 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, and ADJG is defined, HSDPAFm-cgIdentifier value is not allowed to be ‘not defined’
HSDPA FMCG MUST BE DEFINED IF HSDPA ENABLED AND ADJG(S) CREATED UNDER THE WCEL
WCEL_M_0008 WCEL Modify If the HSDPA-enabled param-eter value is Enabled, AMR-WithHSDSCH is Enabled, and ADJG is defined, RTWithHSD-PAFmcsIdentifier value is not allowed to be ‘not defined’
RT HSDPA FMCG MUST BE DEFINED IF HSDPA ENABLED FOR THE WCEL
WCEL_M_0009 WCEL Modify The following HSDPA feature related parameters request object locking when modified: HSDPAEnabled, PtxMaxHS-DPA, HSPDSCHCodeSet, MaxNbrOfHSSCCHCodes
OPERATION REQUIRES WCEL OBJECT TO BE LOCKED
WCEL_M_0010 WCEL Modify If AMRDirReCell (Usage of Directed Retry of AMR call Inter-system Handover) is Enabled, and the target cell of the directed retry of AMR call is the cell whose ADJGid (Inter-system adjacency identifier) has the value 0 , then Adjg-SIB(Include in System Infor-mation ) must be default (yes)
ADJG-AdjgSIB SHOULD NOT BE SET AS 0 (NO) WHEN AMR CALL INTER-SYSTEM HANDOVER IS ON
WCEL_M_0011 WCEL Modify CId (Cell identifier) is unmodifi-able
CELL IDENTIFIER MAY NOT BE CHANGED
WCEL_M_0012 WCEL Modify UARFCN (UTRA Absolute Radio Frequency Channel Number) is unmodifiable
UARFCN MAY NOT BE CHANGED
WCEL_M_0013 WCEL Modify WCEL - WCELGlobalCNid -WCELPLMNid (PLMN identity) is unmodifiable
THE IDENTIFIER OF PLMN NOT MODIFIABLE
WCEL_M_0014 WCEL Modify WCEL - WCELGlobalCNid -WCELCSCNId (CS Core Network Identity) is unmodifi-able
CS CN IS UNMODIFIABLE
WCEL_M_0015 WCEL Modify WCEL - WCELGlobalCNid -WCELPSCNId (PS Core Network Identity) is unmodifi-able
PS CN IS UNMODIFIABLE
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
DN0934038Issue 01A
59
WCDMA RAN RNW consistency checking rules WCEL consistency checking rules
Id:0900d8058070fa8c
WCEL_M_0016 WCEL Modify The folllowing parameters request WCEL object locking before a modification: NbrOf-SCCPCHs (Number of SCCPCHs), CellRange (if Nokia BTS with 3GPP inter-face is involved), PtxCellMax (Cell maximum transmission power), EbNoSetIdentifier, AICHTraTime, PI_amount, PRACHScramblingCode, RACHCapacity, PowerOff-setSCCPCHTFCI
OPERATION REQUIRES WCEL OBJECT TO BE LOCKED
WCEL_M_0017 WCEL Modify "If NBAPCommMode is NB/RSXXX, The following parameters request wcel object locking before a modifi-cation. Cell Reconfig Parame-ters: . PtxPrimarySCH . PtxSecSCH . PtxPrimary-CPICH . PtxPrimaryCCPCH PRACH parameters: . AllowedPreambleSignatures . AllowedRACHSubChan-nels . PtxAICH SCCPCH parameters: . ToAWS_CCH . ToAWE_CCH . PtxSCCPCH1, PtxSCCPCH2, PtxSCCPCH3 . PtxPICH"
OPERATION REQUIRES WCEL OBJECT TO BE LOCKED
WCEL_M_0018 WCEL Modify If HSUPA2MSTTIEnabled is modified, RNC must ensure that the WCEL operational state is BL-U (blocked by user)
OPERATION REQUIRES WCEL OBJECT TO BE LOCKED
WCEL_M_0019 WCEL Modify If MaxTotalUplinkSymbolRate is modified, RNC must ensure that the WCEL operational state is BL-U (blocked by user)
OPERATION REQUIRES WCEL OBJECT TO BE LOCKED
WCEL_M_0020 WCEL Modify WCEL and the Intra-frequency adjacency within it must have have different scrambling codes (PriScrCode)
ADJS (INTRA-FREQ ADJ) AND SOURCE WCEL MUST HAVE DIFFERENT DL_PRI_SCR_CODE
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
60 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8c
WCEL consistency checking rules
WCEL_M_0021 WCEL Modify WCEL and the additional Intra-frequency adjacency within it must have have different scrambling codes (PriScr-Code)
ADJD AND SOURCE CELL MUST HAVE DIFFERENT PRIMARY SCRAMBLING CODE
WCEL_M_0022 WCEL Modify The count of CCH Setup enabled WCEL's must not exceed the license CCHSetup capacity limit.
THE COUNT OF CCH SETUP ENABLED WCEL'S EXCEEDS THE LICENSE CCHSETUP CAPACITY LIMIT.
WCEL_M_0023 WCEL Modify WCEL-PWSMCellGroup, WCEL-PWSMShutdownOr-der, WCEL-PWSMShutdown-RemCell and WCEL-PowersaveHSPAType cannot be modified if WBTS-PWSMI-nUse is ON.
PWSMCELLGROUP,PWSM-SHUTDOWNOR-DER,PWSMSHUTDOWNREMCELL,POWERSAVEHSPA-TYPE CAN NOT BE MODIFIED IF PWSMINUSE IS ON
WCEL_U_0001 WCEL Unlock If NBAPCommMode (NBAP Communication Mode) mis-matches with NEtype(Ne-type), WCEL unlocking is not allowed.
MISMATCH BETWEEN NBAP COMMUNICATION MODE AND NE-TYPE OF NODEB
WCEL_U_0002 WCEL Unlock If HSDPAEnabled(HSDPA Enabled) is Enabled, the optional license HSDPA state should be ON
BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON
WCEL_U_0003 WCEL Unlock If HSDPADynamicRe-sourceAllocation is Enabled, HSDPA and HSDPA Dynamic Resource Allocation license state should be ON
BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA DYNAMIC RESOURCE ALLOCATION LICENCE STATE CON-FIG/OFF, NOT ON
WCEL_U_0004 WCEL Unlock If the maximum code value in HSPDSCHCodeSet is higher than 10, HSDPA 15 Codes license state should be ON
HSDPA 15 CODES LICENCE STATE CONFIG/OFF, NOT ON
WCEL_U_0005 WCEL Unlock If the maximum code value in HSPDSCHCodeSet is between 5 and 10, the optional license HSDPA 15 Codes or HSDPA 10 Codes state should be ON
HSDPA 10 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA 15 CODES LICENCE STATE CONFIG/OFF, NOT ON
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
DN0934038Issue 01A
61
WCDMA RAN RNW consistency checking rules WCEL consistency checking rules
Id:0900d8058070fa8c
WCEL_U_0006 WCEL Unlock If HSUPAEnabled (HSUPA Enabled) is Enabled, the HSDPA(optional) and HSDPA Dynamic Resource Allocation (optional), and HSUPA X Users (optional, according to value of HSUPAXUsersEn-abled) license states should be ON
(HSUPA 3 USERS PER BTS LICENCE STATE NOT ON HSUPA 12 USERS PER BTS LICENCE STATE NOT ON HSUPA 24 USERS PER BTS LICENCE STATE NOT ON HSUPA 60 USERS PER BTS LICENCE STATE NOT ON ) HSDPA DYNAMIC RESOURCE ALLOCATION LICENCE STATE CON-FIG/OFF, NOT ON BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON
WCEL_U_0007 WCEL Unlock If HSUPAEnabled is Enabled, the AAL2UPUsage on the con-nected COCO should be of the HSUPA or HSPA type
INVALID USERPLANE WHEN HSUPA ENABLED
WCEL_U_0008 WCEL Unlock If the value of HSPAQoSEn-abled is 1(QoS prioritization for HSPA NRT connections), HSDPA (optional) and HSDPA Dynamic Resource Allocation (optional) and QoS Aware HSPA Scheduling (optional) license states should be ON
BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA DYNAMIC RESOURCE ALLOCATION LICENCE STATE CON-FIG/OFF, NOT ON THE STATE OF LICENCE FEATURE QOS AWARE HSPA SCHEDULING IS NOT ON
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
62 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8c
WCEL consistency checking rules
WCEL_U_0009 WCEL Unlock If the value of HSPAQoSEn-abled is 2 (HSPA streaming is in use), HSDPA (optional) and HSDPA Dynamic Resource Allocation (optional), and QoS Aware HSPA Scheduling (optional), and HSPA with Streaming QoS Support (optional) license states should be ON
BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA DYNAMIC RESOURCE ALLOCATION LICENCE STATE CON-FIG/OFF, NOT ON THE STATE OF LICENCE FEATURE QOS AWARE HSPA SCHEDULING IS NOT ON THE STATE OF LICENCE FEATURE HSPA WITH STREAMING QOS SUPPORT IS NOT ON
WCEL_U_00010 WCEL Unlock If the value of MaxNbrOfHSS-CCHCodes is higher than 1, the HSDPA (optional), HSDPA Dynamic Resource Allocation (optional), and HSDPA Code Multiplexing (optional) and ( HSDPA 15 Codes(optional) or HSDPA 10 Codes (optional) ) license states should be ON
BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA DYNAMIC RESOURCE ALLOCATION LICENCE STATE CON-FIG/OFF, NOT ON HSDPA CODE MULTIPLEXING LICENCE STATE CON-FIG/OFF, NOT ON HSDPA 10 CODES LICENCE STATE CONFIG/OFF, NOT ON HSDPA 15 CODES LICENCE STATE CONFIG/OFF, NOT ON
WCEL_U_0011 WCEL Unlock If the value of CellRange is between 20Km and 35Km, the Extended cell 35km(optional) or Extended cell 60km(optional) or Extended cell 180km(optional) license state should be ON
NEEDED EXTENDED CELL RANGE LICENCE STATE CONFIG/OFF, NOT ON
WCEL_U_0012 WCEL Unlock If the value of CellRange is between 35Km and 60Km, Extended cell 60km(optional) or Extended cell 180km(optional) license state should be ON
NEEDED EXTENDED CELL RANGE LICENCE STATE CONFIG/OFF, NOT ON
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
DN0934038Issue 01A
63
WCDMA RAN RNW consistency checking rules WCEL consistency checking rules
Id:0900d8058070fa8c
WCEL_U_0013 WCEL Unlock If the value of CellRange is bigger than 60Km, Extended cell 180km(optional) license state should be ON
NEEDED EXTENDED CELL RANGE LICENCE STATE CONFIG/OFF, NOT ON
WCEL_U_0014 WCEL Unlock If the value of HSDPA64UsersEnabled is Enabled, HSDPA (optional) and the HSDPA 64 Users per Cell (optional) license state should be ON
BASIC HSDPA WITH QPSK AND 5 CODES LICENCE STATE CONFIG/OFF, NOT ON
WCEL_U_0015 WCEL Unlock "If the value of MaxTotalU-plinkSymbolRate is 2 (3840 kbps, 2*SF2), at least one HSUPA X Users(optional) license state should be ON and the HSDPA 2.0 Mbps(optional) license state should be ON"
THE LICENCE STATE OF BASIC HSUPA BTS ERROR HSUPA 2.0 MBPS LICENCE STATE NOT ON
WCEL_U_0016 WCEL Unlock If HSUPA is activated, it must be activated in all cells that use the same frequency (UARFCN) in the same BTS.
THE HSUPA STATE OF WCELS WITH SAME UARFCN INCONSISTENCY
WCEL_U_0017 WCEL Unlock If HSUPA is deactivated, it must be deactivated in all cells that use the same frequency (UARFCN) in the same BTS.
THE HSUPA STATE OF WCELS WITH SAME UARFCN INCONSISTENCY
WCEL_U_0018 WCEL Unlock If HSUPA2MSTTIEnabled is set to Enabled, the HSUPA 2ms TTI (optional) license state should be ON
LICENSE HSUPA 2MS TTI IS NOT ON
WCEL_U_0019 WCEL Unlock If MaxTotalUplinkSymbolRate is set to (5760kbps, 2*SF2+2*SF4), the HSUPA 5.8Mbps (optional) license state should be ON
LICENSE HSUPA 5.8MBPS IS NOT ON
WCEL_U_0020 WCEL Unlock If WCEl-HSPA72UsersPerCell is set to Enabled, the license state of 'HSPA 72 Users Per Cell'(optional) should be ON
LICENSE STATE OF HSPA 72 USERS PER CELL MUST BE ON FOR CELL UNLOCK-ING WHEN HSPA72USERSPERCELL IS ENABLED.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
64 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa8c
WCEL consistency checking rules
WCEL_U_0021 WCEL Unlock If PCH24kbpsEnabled is Enabled and NbrofSCCPCHs is greater than 1, then the 24kbps Paging Channel License state must be ON for the purpose of cell unlocking
24KBPS PAGING CHANNEL LICENSE STATE IS NOT ON.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 22 WCEL consistency checking rules (Cont.)
DN0934038Issue 01A
65
WCDMA RAN RNW consistency checking rules WLCSE consistency checking rules
Id:0900d8058070fa8e
24 WLCSE consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
WLCSE_C_0001 WLCSE Create A WSMLC object must be found in the RNC
WSMLC object cannot be found from RNW database.
WLCSE_C_0002 WLCSE Create The maximum amount of WLCSE objects in RNW database is 8000
MAXIMUM NUMBER OF WLCSES EXCEEDED
WSMLC_M_0001 WLCSE Modify If the parent WBTS has WBTS-BroadcastSIB15 as Enabled, the WLCSE cannot be deleted for a cell
WLCSE CAN NOT BE DELETED FOR A CELL IF ITS PARENT WBTS HAS WBTS-BROADCASTSIB15 AS ENABLED
WLCSE_D_0001 WLCSE Delete If a parent WBTS has WBTS-BroadcastSIB15 as Enabled, a WLCSE can not be deleted for a cell
WLCSE CAN NOT BE DELETED FOR A CELL IF ITS PARENT WBTS HAS WBTS-BROADCASTSIB15 AS ENABLED
Table 23 WLCSE consistency checking rules
66 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa90
WRAB consistency checking rules
25 WRAB consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
WRAB_M_0001 WRAB Modify WRAB cannot be modified if there are some unlocked WCELs related
MODIFICATION OF WRAB IS REJECTED DUE TO ITS ASSOCIATION WITH AN UNLOCKED WCEL
WRAB_D_0001 WRAB Delete WRAB cannot be deleted if there is association with some WCELs
Table 24 WRAB consistency checking rules
DN0934038Issue 01A
67
WCDMA RAN RNW consistency checking rules WSG consistency checking rules
Id:0900d8058070fa92
26 WSG consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
WSG_CM_0001 WSG Create/Modify A WSG object can be created and modified when the related WANE object is found in the database, or if WANE id is default
WANE NOT FOUND
Table 25 WSG consistency checking rules
68 DN0934038Issue 01A
WCDMA RAN RNW consistency checking rules
Id:0900d8058070fa94
WSMLC consistency checking rules
27 WSMLC consistency checking rulesThe table below lists consistency checking rules.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
WSMLC_CM_0001 WSMLC Create/Modify The LCSInterfaceOption parameter can be changed to Iupc only if either NW_AGPS_SUPPORT or AGPS_SUPPORT option is enabled, and if the IUPC_INTERFACE option is enabled
WSMLC IU-PC INTERFACE NOT SUPPORTED
WSMLC_CM_0002 WSMLC Create/Modify NW_AGPS_SUPPORT can be enabled only if LCSInterfa-ceOption is Iupc
PARAMETER INTERDE-PENDENCE ERROR
WSMLC_CM_0003 WSMLC Create/Modify The NetworkIndicatorFor-SAS/SignallingPointCodeOf-SAS parameters can be changed to valid value only if either NetworkBasedAGPS or AGPS_SUPPORT option is enabled and WSMLC-LCSIn-terfaceOption parameter is set to IUPC
IU PC INTERFACE FOR NETWORK ASSISTED GPS NOT CONFIGURED
WSMLC_CM_0004 WSMLC Create/Modify The LCSInterfaceOption parameter can be changed to adif_c only if either NW_AGPS_SUPPORT or AGPS_SUPPORT option is enabled, and if the ADIF_INTERFACE option is enabled
WSMLC A-GPS DATA INTERFACE NOT SUP-PORTED
WSMLC_CM_0005 WSMLC Create/Modify PreferredAGPSMethod can be changed to the UE base method only if UEBasedAGPS is enabled
PARAMETER INTERDE-PENDENCE ERROR
WSMLC_CM_0006 WSMLC Create/Modify PreferredAGPSMethod can be changed to NW Based Method only if NetworkBasedAGPS is enabled
PARAMETER INTERDE-PENDENCE ERROR
WSMLC_CM_0007 WSMLC Create/Modify Parameter OperationalMode can select the SAS Centric mode only when LCSInterfa-ceOption has the value Iupc
SAS CENTRIC MODE CAN ONLY BE SELECTED IF LCSINTERFACEOPTION HAS VALUE IUPC
Table 26 WSMLC consistency checking rules
DN0934038Issue 01A
69
WCDMA RAN RNW consistency checking rules WSMLC consistency checking rules
Id:0900d8058070fa94
WSMLC_CM_0008 WSMLC Create/Modify Parameter OperationalMode cannot select the SAS Centric mode when LCS Support for Anchoring has the value Enabled
LCS Support for Anchoring can be enabled only when Operational Mode of LCS is RNC Centric Mode
WSMLC_CM_0009 WSMLC Create/Modify The priority of Shape is unique under CIRTTEmergency-ShapeList and CIRTTShapeList separately if the value is not 0 (disabled)
THE SHAPE PRIORITY MUST BE UNIQUE UNDER CIRTTSHAPE PRIORITY LIST
WSMLC_CM_0010 WSMLC Create/Modify At least one shape priority is valid ( not 0) under CIRTTE-mergencyShapeList and CIRTTShapeList separately
THE CIRTT SHAPE PRIORITY LIST SHOULD NOT BE EMPTY
WSMLC_CM_0011 WSMLC Create/Modify The selected shapes in the list (CIRTTShapeList, CIRTTE-mergencyShapeList) have pri-orities in a descending sequence without gaps
DEFINED CIRTT SHAPE PRIORITIES ARE NOT DESCENDING FROM THE HIGHEST PRIORITY WITHOUT GAPS
WSMLC_CM_0012 WSMLC Create/Modify NW Based A-GPS' can only be enabled if the LCS Interface option is Iupc
WSMLC-NETWORK-BASEDAGPS CAN BE ENABLED ONLY IF WSMLC-LCSINTERFA-CEOPTION IS SET TO IUPC
WSMLC_D_0001 WSMLC Delete A WLCSE object should not exist
WSMLC CANT BE DELETED
WSMLC_D_0002 WSMLC Delete WBTS-BroadcastSIB15 cannot be enabled when WSMLC-LCSInterfaceOption is not IUPC.
WBTS-BROADCASTSIB15 CAN NOT BE ENABLED WHEN WSMLC-LCSIN-TERFACEOPTION IS NOT IUPC.
Checking rule identifier (ID)
Object type
Operation type
Check description Error text
Table 26 WSMLC consistency checking rules (Cont.)