OWT Timber Bolts installed

shown with 56637 Post to Beam Bolt Inline connector

dato cut required

dato cut required

Timber Bolts may be installed as standalone fastener or with many

OZCO connector options

1

Installation Instructions,OWT Timber Bolts

V1.00 - Installation Instructions effective May 1, 2015 and reflects information that available as of April 10, 2014. This information is updated periodically and should not be relied upon after May 1, 2015. Please visit www.OZCOBP.com to get current informationInstallation Instructions, OWT Timber Bolts

[101-152] 4-6"

Assembly, OWT Timber Bolt 4-6"56649-10

[152-203] 6-8"

Assembly, OWT Timber Bolt 6-8"56650-10

[203-254] 8-10"

Assembly, OWT Timber Bolt 8-10"56651-10

[254-304] 10-12"

Assembly, OWT Timber Bolt 10-12"56652-10

.375

5/16" clearance

hole

3/4" clearance

hole

19.05.75

15.88.63

38.101.50

25.401.00

15.24.60

OZCOV1.00 - Installation Instructions effective May 1, 2015 and reflects information that available as of April 10, 2014. This information is updated periodically and should not be relied upon after May 1, 2015. Please visit www.OZCOBP.com to get current informationInstallation Instructions, OWT Timber Bolts 2

V1.00 - Installation Instructions effective May 1, 2015 and reflects information that available as of April 10, 2014. This information is updated periodically and should not be relied upon after May 1, 2015. Please visit www.OZCOBP.com to get current informationInstallation Instructions, OWT Timber Bolts

Suggested Tools(others may be required)

3

mark locations

plate temporarily installed

for installations without post to beam connector, proceed to next step

step 1V1.00 - Installation Instructions effective May 1, 2015 and reflects information that available as of April 10, 2014. This information is updated periodically and should not be relied upon after May 1, 2015. Please visit www.OZCOBP.com to get current informationInstallation Instructions, OWT Timber Bolts 4

plate from step 1 removed

secure as desired

beam can be nailed/screwed in place(instead of clamped) in area covered by plate shown in step 1

pencil marks

step 2V1.00 - Installation Instructions effective May 1, 2015 and reflects information that available as of April 10, 2014. This information is updated periodically and should not be relied upon after May 1, 2015. Please visit www.OZCOBP.com to get current informationInstallation Instructions, OWT Timber Bolts 5

3/4drill through

beam & post"

installation example without post to beam

connector

step 3V1.00 - Installation Instructions effective May 1, 2015 and reflects information that available as of April 10, 2014. This information is updated periodically and should not be relied upon after May 1, 2015. Please visit www.OZCOBP.com to get current informationInstallation Instructions, OWT Timber Bolts 6

adjust as necessary before installation

repeat on opposite side

installation example without post to beam

connectorstep 4V1.00 - Installation Instructions effective May 1, 2015 and reflects information that available as of April 10, 2014. This information is updated periodically and should not be relied upon after May 1, 2015. Please visit www.OZCOBP.com to get current informationInstallation Instructions, OWT Timber Bolts 7

Tool Required3/8" Driver

(Hex Cap Nut)provided

install caps finger tight; both sidesDO NOT USE POWER DRIVER

3/8" Driver

cutaway view

step 5V1.00 - Installation Instructions effective May 1, 2015 and reflects information that available as of April 10, 2014. This information is updated periodically and should not be relied upon after May 1, 2015. Please visit www.OZCOBP.com to get current informationInstallation Instructions, OWT Timber Bolts 8