www.apexinst.com
919-557-7300 or 800-882-3214Fax: 919-557-7110
Website: www.apexinst.comContact: [email protected]
Apex Instruments, Inc.204 Technology Park Lane
Fuquay-Varina, N.C. 27526, U.S.A.
MERCURY
ACCESSORIES
ISOKINETIC
EquipmEnt Catalog
GAS ANALYSIS
FLOW PRESSURE
INTRODUCTION
800-882-3214 /919-557-7300 www.apexinst.com
FLOW, PRESSURE & TEMPERATURE 2D/3D Accu-Flow Measurement Systems Type “S” Pitots, Standard Pitots, Flanges, Manometers, Anemometers, Barometers, Thermocouple Assembly Port Adapters, Packing Glands
MERCURY AND gAS SAMPLINg SYSTEMS & EQUIPMENT Sorbet Trap and Method 30B XC-6000EPC Hg Meter Consoles Dual Sorbent Trap Probes Heated Sample Lines Stirling Gas Conditioner Method 30B Manual Console, XC-260 XC-30B Automatic Console Gas Sampling, Meter Consoles Miniature Probes, Liners, Vost Kit, Tedlar Bags, Glassware
ISOKINETIC SAMPLINg EQUIPMENT Isokinetic Meter Consoles Pumps, Method 5 Probes, Liners Nozzles, Umbilicals, Sample Lines Glassware & Accessories Method Equipment Illustrations
gAS ANALYSIS EQUIPMENT Orsat Analyzers Combustion Gas Analyzers Fryite Analyzers; Flow Control Moisture Analyzers Heated Filter Assemblies IRM Probes, Sintered Filter Assembly Heated Sample Lines Temperature Controllers Gas Conditioners/Condensers Data Acquisition System Transportable CEM Systems
APPENDIX Conversion Factors Equations Nomenclature
INDEX Alphabetical Product Listing
SOURCE TESTINg ACCESSORIES PFA Impingers, Filters Assemblies, Fittings, Tubing Dry Gas Meters, Quick Connects Electrical Components Pumps, Cases, Monorail Systems Fittings, Specialty Supplies Reference Manuals Replacement Parts
SAMPLE RECOVERY/ANALYTICAL Filter Media, In-Stack Thimbles Balances, Brushes, Bottles Drying Agents and Accessories
CALIBRATION EQUIPMENT & SERVICES Calibration Orifice Sets Dry Gas Reference Meters Wet Test Meters, Meter Calibrations Pitot Calibration Calibrations Documentation
Typical Industries & Sources Tested using Apex Equipment:• Acid Plants • Asphalt Plants• Boilers • Cement Plants• Chemical Manufacturing • Furnaces• Incinerators
Apex Instruments was established in 1988 as an American-owned company with worldwide impact. For more than 22 years, Apex Instruments has manufactured equipment for sampling emissions from industrial chimneys and smoke stacks using US-EPA guidelines.
Apex Instruments is committed to offering quality equipment at economical and competitive prices.
Apex Instruments equipment is designed by a staff of experienced stack testers who understand your compliance testing needs. Apex Instruments provides test-ing consoles, probes, pitots, umbilicals, glassware, filters and much more. Cus-tomized equipment for isokinetic, gas and particulate sampling is also available through our excellent sales team. We can design and fabricate any item you need. We are innovators in engineering equipment that is versatile and easy to use.
Our friendly and professional staff is always ready to provide technical support to our customers. Please feel free to contact them at any time for answers to your questions or to place an order.
Development and improvements of Apex Instruments equipment is influenced by valuable feedback and suggestions from customers. We encourage customer in-put and ideas. Our goal is to form tight-knit and long lasting relationships with our customers by providing the best support and equipment for your needs.
The Apex Instruments highly qualified staff is knowledgeable and friendly and always available to assist customers with special projects and equipment.
Contact Apex Instruments today to see how we can be of service to you for your stack testing equipment needs with quality, innovation, and competitive prices.
Catalog Contents Overview
• Incinerators • Municipal Waste Combustors• Petroleum Refineries • Power Plants• Pulp and Paper Mills • Smelters• Steel Mills
www.apexinst.com
919-557-7300 or 800-882-3214Fax: 919-557-7110
Website: www.apexinst.comContact: [email protected]
Apex Instruments, Inc.204 Technology Park Lane
Fuquay-Varina, N.C. 27526, U.S.A.
IsokInetIc catalog
XC-522
XC-5000
XC-40
71
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Delivery:Most orders are shipped within 24 hours of receipt. Please allow extra time for custom orders. Shipping times vary according to the requested shipping service. If you have questions about your shipment please email our shipping management at [email protected].
Return Merchandise AuthorizationCustomers wishing to return items for service or credit need to contact our sales associates for an RMA. Contact by email at [email protected] or by phone (919) 557-7300 or toll free (800) 882-3214.
PricingPrices are published for U.S. customers only. International customers should contact their local distributor. Prices are in U.S. Dollars, FOB shipping point, or Ex Works for International orders. Please confirm current prices by phone, fax or email. Please refer to our price list for a complete list of part numbers and kit configurations.
PaymentFor your convenience, MasterCard, VISA and American Express arewelcome. Company purchase orders are accepted upon credit approval.
We back up this commitment with extensive knowledge of our products, good communication and an excellent customer service history. Our equipment isdesigned by experienced stack testers who know what you face when performing compliance testing.
We encourage you to suggest ideas to improve our equipment. We work closely with you, over the long term, to provide the best equipment for your needs.
CUSTOMER SATISFACTION is guaranteed at APEX INSTRUMENTS.
Hours of Operation:Monday through Friday from 8:00 am
until 5:00 p.m. (EST).
Apex Instruments, Inc. 204 Technology Park Lane
Fuquay-Varina, NC 27526 USA
In U.S. Call Toll Free:1-800-882-3214
Local: 1-919-557-7300fax: 1-919-557-7110
e-mail: [email protected]
www.apexinst.com
ISOKINETIC SOURCE SAMPLING EQUIPMENT
FLOW, PRESSURE & TEMPERATURE
MERCURY ANd GAS SAMPLING SYSTEMS & EQUIPMENT
GAS ANALYSIS EQUIPMENT
APPENdIX
INdEX
ACCESSORIES
Meter Consoles............................................5 - 11
Sample Pumps ............................................12, 13
Nozzles & Nozzle Accessories .......................14, 15
Probes, Liners, Sheaths & Accessories..........16 - 18
Modular Sample Case AssembliesFilter Ovens, Impinger Cases, Risers .............19 - 21
Glassware, Adapters & Impingers ..................22 - 31
Umbilical Cords, Sample LinesMethod 4, Method 5 ....................................32 - 39
Method 8, Method 17 Method 23 .....................................................40 - 43
Method 26A, Method 29, Ontario-Hydro ..............................................44 - 46
Method 201A, Cascade Impactor Kit, Method 202 ..................................................47 - 51
Filter Media, Sample Recovery Desiccator and Desiccants ........................52 - 56
Silica Gel, Balances Calibration Weights .....................................57 - 59
Calibration Equipment, Monorails .............60 - 63
XC-522/XC-572 Components List ............64
Appendix .......................................................65-69
Isokinetic Index ............................................70
isokinetiC sampling equipment
Stationary source sampling is conducted to evaluate gas stream emissions to the atmosphere from stacks, ducts or process exhausts. A pol-lutant’s concentration is measured by extracting a known volume from the gas stream and determining the average stack gas flow rate over the sampling period. The mass emission rate of each constituent then may be calculated. In the area of Stack Sampling Methods, there are 3 major categories of test-ing: Isokinetic Reference Methods, Instrumental Reference Methods (IRM), and Gaseous Sampling (which includes sampling for mercury). Obtaining a representative sample of particulate matter from a gas stream requires a more complex procedure than sampling only for gases. Particles can be either liquid droplets or solids. Representative sampling requires that the velocity of the gas/particle mixture passing into the sampling nozzle must be as close as possible to the velocity of the gas stream in the stack or duct. When the velocities are the same, the sampling is isokinetic. During the entire sampling period, the stack velocity must be monitored constantly and the pumping rate adjusted so that the nozzle intake veloc-ity matches as closely as possible the velocity of the in-stack gas/particle mixture. In addition, the pumping rate needs to be adjusted for differences in pressure, temperature and moisture between the stack conditions and the pump or meter console. The exact steps to conduct this type of sampling are spelled out in U.S. EPA Reference Method 5. This method also requires knowledge of U.S. EPA References Methods 1 through 4. The Apex AutoKineticTM method 5 sampling system offers modular components that can be arranged and re-arranged to perform multiple U.S. EPA Reference Methods. Select from manual, digital or automated meter consoles, as well as a wide range of heated filter and impinger boxes, heavy-wall glassware with unground o-ring ball joints, probes built to customer specified lengths, new designs for umbilical cords, and custom modifications to meet your unique needs. All delivered in a timely manner at a competitive price. For over 22 years, Apex Instruments, Inc., has concentrated on manufacturing equipment designed for use in sampling stationary combustion sources. Apex Instruments has always been directly involved with the envi-ronmental industry, working close with the U.S. EPA. When the Clean Air Act was enacted in 1990 and hazardous air pollutants were identified for control, Apex Instruments was at the forefront of product design, method evaluation and implementation.
Phone: 919-557-7300 or In the U.S. 800-882-3214Monday-Friday, 8:00 a.m. to 5:00 p.m. (Eastern Time)
Fax: Order at your convenience 24 hours a day, 7 days a week 919-557-7110
Website: www.apexinst.com
Please visit our website for additional product information, new product releases, updated materials, manuals, reference data and valuable links.
Please feel free to call our friendly sales staff today!
Vance JonesDomestic Sales,
Customer [email protected]
Janet NicholsSales Manager
John StauberInternational [email protected]
doug Bernhardt Customer Service
ISOKINETIC SAMPLING EQUIPMENT
3
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Apex Isokinetic Source Sampling Systems are rugged versatile equipment designed for extracting a representa-tive flue gas sample from a source to determine dust and fumes emissions in accordance with many U.S. EPA Reference Methods as published in CFR 40 Part 60 Appendix A. The Apex Isokinetic Source Sampling System allows the operator to monitor gas velocities, temperatures, pressures and adjust sample flow rates to obtain a representative flue gas sample.
The results are often used to prove compliance with existing and applicable regulations. It can also be used to characterize the gas stream, tune or optimize the process or combustion source, or validate control processes in place.
isokinetiC sourCe sampling /method 5 and assoCiated methods
Modular Sample Cases, page 19
Probes and Liners, page 16 - 18
Consoles, page 4 - 11
Pumps, page 12 - 13
Umbilicals, page 29
Nozzles, page 14
Glassware, page 22
Featuring the XC-5000 AutoKineticTM Sampler
Versatile System designs for Multiple Methods:
The Apex Method 5 Source Sampling System can be configured with various accessories and used to sample a wide range of pollutants, such as metals, halides and halogens, polychlorinated biphenyls (PCBs), dioxins/furans, polycyclic aromatic hydrocarbons (PAH’s), particle size distributions and an ever-increasing group of pollutants by adaptations of basic test methods. Within our catalog we feature sampling kits and accessories for the most popular isokinetic methods and pollutants of interest. A list of featured methods can be found on page 4.
Method 1 Determination of Sampling Location and Traverse PointsMethod 2 Determination of Stack Gas Velocity and Volumetric Flow RateMethod 3 Determination of Excess Air and Dry Molecular WeightMethod 4 Determination of Moisture In Stack GasesMethod 5 Determination of Particulate Emissions from Stationary Sources
Isokinetic Testing Requires a Thorough Understanding of the First Five Test Methods Presented in the CFR 40 Part 60, Appendix A.
Method 5 - CompactMethod 5 - FlexibleMethod 5 - Rigid
Method 17Method 23Method 26A
Method 29Method 201AMethod 202
4
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
See Links for Methods on Our Website
See Links for Gas Testing Methods
See Links for Flow Testing Methods
METhOd dESCRIPTIONMETHOD 4 Determination of MoistureMETHOD 5 Determination of Particulate
Emissions from Stationary SourcesMETHOD OTM-28 Controlled CondensateMETHOD 17 Particulate by In-stack FiltrationMETHOD 23 Dioxins and Furans
METHOD 0061 Hexavalent Chromium
Recommended Accessories to Convert M5 Kit to Perform:METHOD 26A Hydrogen Halides and HalogensMETHOD 29 Multiple MetalsMETHOD 201A PM10 EmissionsMETHOD 202 Condensable Particulate Matter,
PM 2.5ONTARIO HyDRO ASTM-D6784-02 Mercury
hOW TO GET STARTEd Versatile system designs are available to serve complex and challenging stack testing locations. The Method 5 System, combined with the appropriate accessories, can be used to sample a wide range of pollutants, such as dust, metals, polychlorinated bi-phenyls (PCBs), dioxins/furans, polycyclic aromatic hydrocarbons (PAH’s), particle size distributions and an ever-increasing group of pollutants by adaptations of basic test methods. Contact our helpful sales staff to configure a system to meet your needs.
SELECT METER CONSOLESelect a meter console that is appropriate for the test method and select a configuration that suits your specific conditions.
ChOOSE A PUMPChoose an external pump that suits your specific conditions and desired flow rates.
dETERMINE SAMPLING KITS REQUIREMENTSSelect method specific accessories and kits to complete your system.
NEEd ASSISTANCE?We are never more that a phone call away during normal business hours, and would be glad to help answer any questions you may have. hours of Operation: Monday through Friday from 8:00 am, until 5:00 p.m. (EST).
Fax : (919) 557-7110Email : [email protected] # : (919) 557-7300 (800) 882-3214
Rigid-Set-up
FEATUREd METhOdS Apex Instruments method kits are available for the most popular methods. After choosing the meter console and sample pump, purchase the kit you need to conduct the desired method.
Flexible System
Console & Pump
5
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
The Apex Instruments XC-5000 AutoKineticTM Sampler is designed for conducting US EPA Method 5 and associated isokinetic methods. Take the worry out of isokinetic calculations and the human error out of data entries recorded by hand. The new XC-5000 is compatible with your existing Method 5 stack sampling components. Report preparation is streamlined with accurate data downloadable to files for easy preparation and submission to your regulating agency.
XC-5000 AUTOKINETICTM SAMPLER CONSOLE
Features • Uses standard Apex Instruments sample train components (probe, nozzle, heated filter box, impinger box, etc.)
• Maintains isokinetic sampling conditions without operator assistance
• Calculates stack traverse points
• Calculates correct nozzle diameter for site conditions
• Stores and displays user entered data and parameters
• Upload and download data files
• Performs instantaneous isokinetic sample flow calculations
• Timer alerts operator to move the probe
• Alarms indicate when acceptable conditions are not met
• English or metric units selectable
Model description
XC-5000 AutoKineticTM Sampler Console, 110V
XC-5000-V AutoKineticTM SamplerTM Console, 240V
Sample Pump: Accepts standardmethod 5 pump assemblies.
XC-5000 Isokinetic Source Sampler
XC-5000AutoKineticTM SamplerConsole with Laptop
Wireless or Ethernet Connection Available
Main Power
ProbePower
Color CodedThermocouple
Jacks
Stainless SteelVacuum Pump
Quick Connects
Pump PowerConnection Stainless Steel
Pitot QuickConnects
Ethernet Interface
Umbilical Cable Power Connection
Stainless Steel Sample Quick Connect
LED Display
LEDIndicator
Delta H Calibration
External
Connections
6
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
Specifications
Optional:4 channel analog input module for logging external data (4-20ma, 0-10V, 1-5V).
dimensions:23” x 21” x 12” (58 cm x 53 cm x 30.5 cm).
Weight: 39 lbs. (17.7 kg).
Power: 120V / 60 Hz. 220V / 50 Hz (optional).
Console Power Requirements:120V 15amp max.
Umbilical Connections:Electrical: 4 conductor circular connector grounded shell.Sample line: Stainless Steel 1/2” Quick Connector.Pitot Line: Stainless Steel 1/4” Quick Connectors (optional 3/8”).External pump: Stainless Steel 3/8” Quick Connect.Thermocouples: Type-K standard size.
Communication:Wireless and Ethernet.
Gas Meter: Model AP25, Precision DGM, 0.7 liters per revolution, digital gas volume with Internal Quadrature Encoder with 6 digit LCD display, 1cc resolution.
Temperature Control: Integrated temperature control via the Control and Data Acquisition Board, probe and oven with solid state relays.
Thermocouple display: 7 temperatures displayed simultaneously on the PC User Interface, °F or °C, Probe, Stack, Oven, Filter, Exit, AUX and DGM.
Digital Pressure Transducers for H, and P (Bi-Directional), Barometric.
P +/- 2.5” 0.01” resolution +/- 63mm 0.01 mm resolution
H 0”-5” 0.01” resolutions 0mm-127mm 0.01mm resolution
Barometric 17.7 inHg – 32.5 inHg 0.01 inHg resolution 450 mmHg – 825 mmHg 0.01m mmHg resolution
XC-5000 software screen shot.
Features
• Uses Standard Apex Instruments Sample Train Components (Probe, Nozzle, Heated Filter Box, Impinger Box)• Calculates Stack traverse Points (Method 1)• Stores and Displays User Entered Data and Parameters• Performs Instantaneous Isokinetic Sample Flow Calculations & Controls Isokinetic Flow• Timer Alerts Operator to Move the Probe• English or Metric Units
XC-5000 AutoKineticTM Sampler
Console and Laptop
Wireless or Ethernet Connection Available
7
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
ISOKINETIC SOURCE SAMPLING CONSOLE - MANUALThe XC-500 Series Sampling Console is a rugged, lightweight metering console used to extract gas samples in accordance with US EPA Method 5 for determining source emissions for dust and fumes. The Apex Isokinetic Source Sampler allows the operator to monitor gas velocities, temperatures, pressures and adjust sample flow rates to maintain isokinetic sampling conditions. Comes with digital temperature controllers, a choice between digital or liquid manometers, digital temperature displays and external pump connections. Stainless steel fittings and quick connects are standard. Units in the XC-500 Series are available in Standard or Metric units, 110V or 220VAC, optional internal orsat pump. XC-500 Series Sampling Console features a molded, rugged X-case with side handles for attaching the easy carry strap. The X-case allows for rear door access. Apex Instrument’s Isokinetic Sampling Consoles are manufactured to conform to the construction design criteria and specifications cited in U.S. EPA Method 5, Code of Federal Regulations (40 CFR Part 60) and APTD-0581 documents. All Apex consoles are calibrated prior to shipping.
Slide Out Front PanelThe meter console has a slide-out panel for easy access.
Rear ViewRemovable back panel allows for quick audits.
PortableX-case with sample pump on portable hand cart. (optional)
Temperature Display Manometer Quick
Connects
Dual Column Manometer
Coarse Control Valve
Dry Gas Meter
Fine Control Valve
Heavy Duty Panel Latches
Manometer Zero Adjust Knobs
Manometer Level Adjust
StandardStainless Steel Pitot
Quick Connects
StandardStainless Steel
Sample Quick Connect
Standard Stainless Steel Pump Connection
(Pressure)Umbilical
Cable Power Connection
Color Coded Thermocouple Jacks
Temperature Selector Switch
Vacuum Gauge
Elapsed Timer
Rocker Switches with Magnetic
Circuit Breakers
Optional Orsat Pump and
Rotameter
Rugged Custom Molded X-Case
Digital Filter and Probe Temperature
Controllers
Stainless SteelNon-Reversible Pump
Quick Connect(Vaccum)
Strap
8
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
XE-0523 Sample Pump Mounted in UhMWPolyethylene Case• Motor: 1/4 hp, 120/240V 60/50Hz 4.6/2.3 Amp., RPM 1725/1425• Measured Flow: 3.1 cfm@ 1 inch Hg; 1.5 cfm@ 15 inches Hg • Maximum Vacuum: 25.5 inches Hg • Weight: 35 lbs. (16kg)
XC-522 Source Sampling ConsoleThe Apex Instruments Model XC-522 is a full featured manual meter console. The Apex Isokinetic Source Sampling Console allows the operator to monitor gas velocities, temperatures, pressures and adjust sample flow rates to maintain isokinetic sampling conditions. Designed with convenient display layout for manual data recording.The Apex Instruments Isokinetic Source Sampling Consoles are manufactured to conform to the construction design criteria and specifications cited in U.S. EPA Method 5, Code of Federal Regulations (40 CFR Part 60) and APTD-0581 documents.
Features:• Low Cost - Manual Console• Easy to Operate and Maintain• Rugged, Lightweight, Stackable Case• Removable 19” Front Panel• Carry Strap for Easy Transport• Non-Reversible Sample Pump Connections• Color Coded Thermocouple Jacks• Bright, Easy-to-Read Temperature Displays• Easy-Leveling Dual Column Manometers• Dry Gas Meter with direct read index• Stainless Steel Quick Connects & Fittings
Model description
XC-522 English Meter Console, 120 V/60 Hz
XC-522-V English Meter Console, 240 V/50 Hz
XC-522-O English Meter Console with optional Orsat Pump Assembly, 120 V/60 Hz
XC-522-OV English Meter Console with optional Orsat Pump Assembly, 240 V/50 H
XC-522 English Units (Cubic Feet, oF)
XC-522 Source Sampler
XC-522 Recommended Accessories
Nomographs & Calculators, See Accessories Section
Page 29d
Specifications
Temperature Controllers for Probe and Oven: 1/32 DIN bright red LED display, indicating temperature controllers with separate 25 amp solid state relay, auto-tuning. Standard Type-K jack for input.
Vacuum Gauge: Dual Scale Vacuum Gauge, 0-30” Hg / 0-100kPa.
Sample Pump Connections: 3/8” Quick Connects, Stainless Steel, non-reversible.
Umbilical Connections: Sample Inlet: ½” Stainless Steel Quick-Connect; Pitot Lines: 1/4” (3/8” optional) stainless steel Quick Connect; Electrical: 4 conductor circular connector; Thermocouples: 6 Type K inputs, standard size.
Power: 120V/60Hz standard; 240V/50Hz optional
dimensions: 23” x 21” x 12” (58 x 53 x 30cm) Panel 19”
Weight: 43 lbs (19.5kg)
Gas Meter: Rockwell S110 remanufactured with direct read index, 0.1 cubic feet/revolution, res. 0.001 cubic feet direct read analog totalizer with 999.999 cubic feet capacity.
Manometer: Dual Inclined/Vertical Manometer for determining stack velocity and sample flow rate. Inclined Range 0-1.0” H²0 with 0.01 divisions. Vertical Range 1-10” H²O with 0.1” divi-sions. Fabricated from solid acrylic, precision bored, accurate to +/- 1%. Convenient self-sealing chrome plated brass quick-connects with Viton® O-Rings. Supplied with plastic plugs for positive secondary seal. Temperature display: Panel mount digital thermometer, bright red LED display, 1/8 DIN plastic housing, Range -157° to 1999°F, with separate 7-channel selector switch.
Sample Pumps are sold separately, Page 12-13
9
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
XC-572 Source Sampler
Model description
XC-572 XC-572 Isokinetic Meter Console, Metric, 120V/60Hz
XC-572-V XC-572 Isokinetic Meter Console, Metric, 240 V/50 Hz
XC-572-O XC-572 Isokinetic Meter Console, Metric, with optional Orsat Pump Assembly, 120V/60Hz
XC-572-OV XC-572 Isokinetic Meter Console, Metric, with optional Orsat Pump Assembly, 240 V/50 Hz
XC-572 Metric Units
XC-572 Source Sampling ConsoleThe XC-572 Source Sampling Console is the metric version of the XC-522. It is a full featured, compact, and lightweight Isoki-netic Source Sampler. It has all the great features you want and the reliability you need. Field set up is easy with non-reversible external pump connections and the industry standard 4-pin electrical connector. (External sample pump sold separately).Console allows operators to monitor gas velocities, tempera-tures, pressures, and sample flow rates for maintaining isokinetic sampling conditions.
Specifications
Gas Meter: AP-25 easy to read numeric index with leak check wheel, low pressure drop, rated 42 lpm at 15mm H2O, maximum capacity approx. 70 lpm. Totalizer capacity 9999.9999 cubic meter, resolution 0.1 Liter.
Manometer: Dual Inclined/Vertical Manometer for determin-ing stack velocity and sample flow rate. Inclined Range of 0-26mm H²0 with .2mm. Vertical Range of 26-250mm H²O with .2mm. Fabricated from solid acrylic, precision bored, accurate to +/- 1%. Convenient self-sealing chrome plated brass quick-connects with Viton® O-Rings. Supplied with plastic plugs for positive secondary seal.
Temperature display: Panel mount digital thermometer, bright red LED display, 1/8 DIN plastic housing. Range -105°C to 1372°C, with separate 7-channel selector switch.
Temperature Controllers for Probe and Oven: 1/32 DIN bright red LED display, indicating temperature controllers with separate 25 amp solid state relay, auto-tuning. Standard Type-K jack for input.
Vacuum Gauge: Dual Scale Vacuum Gauge, 0-30” Hg / 0-100kPa.
Sample Pump Connections: 3/8” Quick Connects, Stainless Steel, non-reversible.
Umbilical Connections: Sample Inlet: ½” Stainless Steel Quick-connect; Pitot Lines: 1/4” (3/8” optional) Stainless Steel Quick Con-nect; Electrical: 4 conductor circular connector; Thermocouples: 6 Type K inputs, standard size.
Power: 120V/60Hz standard; 240V/50Hz optional.dimension: 23” x 21” x 12” (58 x 53 x 30cm) Panel 19”.Weight: 40 lbs (18kg)
Features:• Precision gas meter with leak check indicator• Low Cost - Manual Console• Easy Operation and Maintenance• Rugged, Lightweight, Stackable Case• Removable 19” Front Panel• Carry Strap for Easy Transport• Non-Reversible Sample Pump Connections• Color Coded Thermocouple Jacks• Bright, Easy-to-Read Temperature Displays• Easy-Leveling Dual Column Manometer• Stainless Steel Quick Connects & Fittings• Convenient Layout for Manual Data Recording
Low Flow Adapters,VUA,
See Accessories Section
Page 18d
XC-572 Recommended AccessoriesXE-dAA Sample Pump Mounted in UhMWPolyethylene Case• Motor: 1/2 hp, 120V/60Hz 5 1/2 Amp• 2.9 cfm@ 1 inch Hg; 1.4 cfm@ 15 inches Hg • 26.5 inches Hg • Weight: 30 lbs. (14kg)
Sample Pumps are sold separately, Page 12-13
10
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
XC-563 dIGITAL SOURCE SAMPLING CONSOLEApex Instruments Model 563 Source Sampling Console is thedigital equivalent to the XC-522 and XC-572; featuring an AP25Dry Gas Meter with optical encoder and digital totalizer. Theconsole also features differential pressure transducers for Pand H. The temperature controllers, thermometer and timerall have digital displays.
XC-563 Source Sampler
Model description
XC-563 XC-563 Meter Console, 120V/60Hz
XC-563-V XC-563 Meter Console, 240V/50Hz
XC-563-O XC-563 Meter Console, with optional Orsat Pump Assembly, 120V/60Hz
XC-563-OV XC-563 Meter Console, with optional Orsat Pump Assembly, 240V/50Hz
XC-563 Source Sampler Console
Features • Precision Gas Meter with LCD Totalizer• Module with Dual Pressure Transducers• Digital Probe Temperature Control/Display• Vacuum Gauge (Dual Scale)• Stainless Steel Quick Connects and Control Valves• Digital Temperature Display (oF or oC) with up to 6 Type-K Inputs• Non-Reversible External Pump Connections• Removable Front Lid and Back Panel• Digital Display for P Velocity Pressure, and H Orifice Pressure• No Messy Manometer Fluid• Digital Elapsed Timer• Lightweight
Specifications
Umbilical Connections:Electrical: 4 conductor circular connector grounded shell.
Sample Line: Stainless Steel 1/2” Quick Connectors.
Pitot Line: Stainless Steel 1/4” Quick Connectors (optional 3/8”).
External Pump: Stainless Steel 3/8” Quick Connect.
Thermocouples: Type-K Standard Size.
Power: 120V / 60Hz Standard
240V / 50Hz Optional
dimensions: 23” x 21” x 12” (58cm x 53cm x 30.5cm)
Weight: 39 lbs. (17.7 kg).
Sample Pump: Accepts Standard Method 5 Pump Assemblies.
Gas Meter: AP25, 0.7 liters per revolution, digital gas volume total-izer with Quadrature Encoder, 8 digit LCD display, 1cc resolution.
Temperature Control: Digital temperature controllers for probe and oven 1/32 DIN with solid-state relays.
Temperature display: Type-K 3.5 Digit LED display (°C is standard for export). °C/°F selectable via plastic jumper behind front bezel, -105°C to 1372°C range. (-157°F to 1999°F). Separate 7-channel TC selector switch. Standard and Metric Units.
digital Pressure Transducers for h P +/-2.5” range 0.01” resolution
+/-63mm range 0.1mm resolution H 0” - 5” range 0.01” resolution 0” - 127mm range 0.1mm resolution
(Bi-Directional)
Audit Kit for Digital Metering Console. ak-563audit kit
dhM-M100 - Handheld Meriam Manometer
INCLUdES:
Sh-32 - 8 x 10 Molded Plastic Case
SCL-F4 - Plastic Quick-Turn (Luer Lock)
SYR-30ML-LL dhM-M100
Sh-32
SCL-F4SYR-30ML-LL - Syringe, Luer Lock Tip, 30ml with 1 ml Increments
11
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Features• Rugged lightweight case with Molded-In Handle
• Precision Dry Gas Meter with Digital Display
• Minihelic Pressure Gauge
• Internal Diaphragm Pump
• Digital Temperature Display with up to 5 Type-K Inputs (°F)
• All Stainless Steel Fittings and Control Valves
• Digital PID Probe Temperature Controller
• Digital Elapsed Timer (hr:min:sec)
• Vacuum Gauge (Dual Scale)
• Easy Access for Service
METhOd 4 SOURCE SAMPLING CONSOLEThe Apex XC-40 Source Sampler Console is a durable, lightweight meter console ideal for Method 4 (Determination of the Moisture Content of Stack Gas). The meter console can be used with standard impingers and accessories to collect moisture for required calculations. This unit heats the stack probe and with its internal pump pulls 0.75 cfm as required to comply with Method 4.
XC-40 Source Sampler
Method 4 Determination of the Moisture Content of Stack Gas Summary: Stack gas is extracted at constant rate (less than 21lpm) for a minimum volume of 600 liters. Moisture is scrubbed from the sample stream and measured volumetrically or gravimetrically.
Specifications
Gas Meter: Model AP25, 0.7/rev., digital gas volume totalizer, with Quadrature Encoder, 8 digit LCD Display, 1cc resolution.
Flow Indicator: Mechanical Orifice w/Minihelic Pressure Gauge, range (0-2”) or (0-50MM H2O).
Temperature display: Type-K 3.5 Digit LED display (°C is stan-dard for export). °C/°F selectable via plastic jumper behind front bezel, -105°C to 1372°C range. (-157°F to 1999°F).
Probe Temperature Control: Compact, 1/32 DIN autotuning indicating temperature controller with separate 25 amp solid state relay. 115 VAC outlet 5-15R, Type-K jack for input.
Internal Sample Pump: Single cylinder oil-less pump, long life diaphrams, 1/8-27 NPT Connections, Max. vacuum 23” hg, Min. full load speed 2800 rpm, nominal free flow 1.15cfm, 12V 3.8 amps
Vacuum Gauge: Dual Scale, 0 to 30” Hg and 0 to 100kPa.
Power: 115V/60Hz; 240V/50Hz (optional).
Sample Inlet: 1/2” Stainless Steel Quick-Connect (alternate sizes available)
dimensions: HxWxD: 21” x 9.5” x 14” (53 cm x 24 cm x 35.5 cm)
Weight: 22 lbs (9.98kg)
Model descriptionXC-40 Standard Metering Console with Digital Gas Meter, plus
Digital 8 digit LCD Totalizer. -.001 cu.ft. res. (120V/60Hz)
XC-40-V Standard Metering Console with Digital Gas Meter, plus Digital 8 digit LCD Totalizer. -.001 cu.ft. res.(240V/50 Hz)
XC-40M Metric Metering Console with Digital Gas Meter and a 8 digit Digital LCD Totalizer. 1cc res. (120V/60Hz)
XC-40M-V Metric Metering Console with Digital Gas Meter and a 8 digit Digital LCD Totalizer. 1cc res. (240V/50 Hz)
Method 4 Source Sampler Console
See more information on our Method 4 Condenser Assemblies and Accessories for use with theXC-40 Source Sampler Console.
Method 4 Condenser Assemblies, Page 33
12
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
The open tubular steel frame is designed for the meter console to sit on top of the pump frame. For easy maneuverability, an optional wheeled handle assembly is available. For use with XF version sample pump assembly.
XF-05hW Optional Pump FrameHandle Assembly. Black Tubular Steel with 8” Wheels
XF-05hW
METhOd 5 PUMP ASSEMBLIES
Lubricated Rotary Vane Pump (0523)The Lubricated Rotary Vane Pump includes two 5’ wire-reinforced, kink-free hoses with nonreversible quick connects. The pump is mounted in either the new, improved, stronger tubular steel frame, or the standard x-case with removable covers providing easy access for service. The wick style lubricator requires less maintenance. Option “V” added for 240V.
Specifications• Motor: 1/4hp, 120/240V 60/50Hz 4.6/2.3 Amp., RPM 1725/1425• Measured Flow: 3.1 cfm@ 1 inch Hg; 1.5 cfm@ 15 inches Hg • Maximum Vacuum: 25.5” Hg• Weight: 35 lbs., (16kg)
XE-0523
XE-0523 Pump Shown with Console
Model description
XE-0523 Rotary Vane Pump in a Molded X-Case (120V/ 60 Hz)
XE-0523-V Rotary Vane Pump in a Molded X-Case (240V/ 50Hz)
XE-0523 Rotary Vane Pumps
Model description
XF-0523 Rotary Vane Pump in Tubular Steel Frame (120V / 60 Hz)
XF-0523-V Rotary Vane Pump in Tubular Steel Frame (240V / 50Hz)
XF-0523 Rotary Vane Pumps
Model description
E-0523 External Pump Assembly (std), Vane Pump, Open Aluminum Frame, Lubricator, 5ft Pwr Cord & Hoses,Stainless Quick Connects Standard, 120V
E-0523-V External Pump Assembly (std), Vane Pump, Open Aluminum Frame, Lubricator, 5ft Pwr Cord & Hoses, Brass Quick Connects Standard, 240V
E-0523 Open Aluminum Pump Frame
E-0523
13
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
XE-dAA
Model Pump
XE-DAA Double Headed Diaphragm Pump in a Molded X-Case, 110V/60Hz
XE-DAA-V Double Headed Diaphragm Pump in a Molded X-Case, 220V/50Hz
XE-dAA Pumps diaphragm Pumps
XF-dAA Pump Shown with Console and XF-05hW Optional
Pump Frame
XF-05hW Optional Pump FrameHandle Assembly. Black Tubular Steel with 8” Wheels.
XF-05hW
XF-dAA
Model Pump
XF-DAA Double Headed Diaphragm Pump in Tubular Steel Frame, 110V/60Hz
XF-DAA-V Double Headed Diaphragm Pump in Tubular Steel Frame, 220V/50Hz
XF-dAA diaphragm Pumps
double headed diaphragm Pump (dAA)The Double Headed Diaphragm Pump will never require any lubrication. Pump is easy to service within its frame and includes a power cord, two 5’ wire-reinforced, kink-free hoses with non-reversible stainless steel quick connects (this pump is not recommended for use in extremely cold environments).
METhOd 5 PUMP ASSEMBLIES
Specifications• Motor: 1/2hp, 120V/60Hz, 5 1/2 Amp• Measured Flow: 2.9 cfm@ 1 inch Hg; 1.4 cfm@ 15 inches Hg • Maximum Vacuum: 26.5” Hg• Weight: 30 lbs., (14kg)
*See Accessories for Spare parts
Model Pump
E-DAA External Pump Assembly (alt), Double Diaphragm Pump, Open Frame, 5ft Pwr Cord & Hoses, 120V
E-DAA-V External Pump Assembly (alt), Double Diaphragm Pump, Open Frame, 5ft Pwr Cord & Hoses, S.S. Quick Connects Standard, 240Volt
E-dAA Open Aluminum Pump Frame
14
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
NOZZLES FOR ISOKINETIC SAMPLING
Unique to Apex Instruments, the Nozzle Shank has integrated Ferrule with O-Ring Groove. O-Ring (O-O14V) shown.
Nozzle Sets come in stainless steel, glass, quartz, inconel or FEP lined. Includes a Nozzle Case, Seven Nozzles, (sizes 4, 6, 8,10, 12,14,16) and select Accessories.
Nozzle Sets
Nozzle w/ Female 14/35 Taper Joint
Size
-�
Standard I.D. Stainless Steel NS-�
Alloy 600
NI-�
FEP Lined
Stainless Steel
NST-�
Silico Coated
Stainless Steel
NSIL-� 4 1/8 0.120 3.048 5 5/32 0.152 3.861 6 3/16 0.180 4.572 7 7/32 0.209 5.309 8 1/4 0.245 6.223 9 9/32 0.277 7.05610 5/16 0.305 7.74711 11/32 0.334 8.48412 3/8 0.370 9.39813 13/32 0.402 10.2114 7/16 0.430 10.9215 15/32 0.459 11.6616 1/2 0.495 12.5717 17/32 0.527 13.3918 9/16 0.568 14.4
Individual Nozzles
Apex Instruments Threaded Nozzle Set (NS-TH-SET) features the larger ID nozzles for low stack gas velocity and a buttonhook Nozzle Blank (NS-THB) with a tapered fitting. The set includes seven SS Nozzle Tips that thread onto the Nozzle Blank. Sizes include 5/8”, 11/16”, 3/4”, 13/16”, 7/8”, 15/16” and 1”. ns-th-set
Note: When using O-Ring, a Bored Union, (P/N: N-10UB) is required.
NS-SET
NG-SET
Model DescriptionNS-SET Stainless Steel
Nozzles. Includes Four 5/8” Tube Nuts, O-Viton Rings
NG-SET Glass Nozzles. Includes Three 5/8” Glass Filled PTFE Ferrules
NI-SET Alloy 600 Nozzles, with Inconel Tube Nut
NQ-SET Quartz Nozzles (Order Ferrules Separately)
NST-SET FEP lined, Stainless Steel Nozzles, Includes Four 5/8” Tube Nuts, O-Viton Rings
NSIL-SET Silica Coated Stainless Steel Nozzle Set
Nozzle Sets
Size Nominal I.D. Stainless SteelNS-TH� Inch Decimal mm
20 5/8 0.625 15.87522 11/16 0.6875 17.46224 3/4 0.750 19.05 26 13/16 0.8125 20.63728 7/8 0.875 22.22530 15/16 0.9375 23.81232 1 1.0 25.4B Blank
Oversized NozzlesSize-�
Standard I.D. Glass NG-�
Quartz NQ-�
Glass with Taper Joint NG-�T
Quartz with Taper Joint NQ-�T
4 5/8 0.125 3.175 5 5/32 0.156 3.962 6 3/16 0.180 4.775 7 7/32 0.209 5.308 8 1/4 0.250 6.35 9 9/32 0.281 7.13710 5/16 0.312 7.92411 11/32 0.343 8.71212 3/8 0.375 9.52513 13/32 0.406 10.31214 7/16 0.437 11.09915 15/32 0.468 11.88716 1/2 0.500 12.717 17/32 0.531 13.48718 9/16 0.558 14.173
Inch Decimal mm
Inch Decimal mm
Apex Instruments offers Button-Hook Nozzles in mul-tiple materials. The size needed for isokinetic sampling depends on the stack gas velocity; the material depends on the stack temperature and the sampling method. The most popular nozzles are constructed from seamless 316 stainless steel and can be coated with FEP or SilcoSteel-CR®. Other nozzle materials include Borosilicate Glass, Alloy 600 and Quartz. Standard sampling nozzles are 4” long and have a 5/8” o.d. shank for attaching to the probe union. Stainless steel nozzles are configured with an O-Ring to aid in positive leak checks. A bored out union is needed with Apex O-Ring nozzles, although a standard union can be used if the O-Ring is removed. Other sizes and configurations are available. Nozzles must be measured before initial use. Glass and Quartz Nozzles are available with a female 14/35 ground glass taper joint eliminating the need for the 5/8” union. For use with male taper joint probe liners.
Call For Additional Information
Call For Additional Information
15
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Model Description (Standard 5/8”)N-10 5/8” Stainless Steel Tube Nut
NI-10N 5/8” Alloy 600 Tube Nut
N-10TG 5/8” Glass Filled PTFE Tube Nut
Model Description (Standard 5/8”)N-10BR Thrust Backer Ring, 5/8” for O-Ring
Seal, Stainless Steel. For use with O-113V
O-113V Viton® 5/8” O-Ring to seal liner (for use with N-10BR)
O-113V-DZ Viton® 5/8” O-Ring to seal liner (for use with N-10BR), Dozen
O-014V Viton O-Ring for 1/2” UltraTorr Fitting when Adapting to 1/4” UltraTorr Fitting
O-014V-DZ Viton® O-Ring for 1/2” UltraTorr Fitting when Adapting to 1/4” UltraTorr Fitting, Dozen
Model Description (Standard 5/8”)N-10 5/8 inch Stainless Steel Tube Nut.
N-10TG 5/8 inch Glass Filled Teflon Tube Nut, 12 flats (sided) Fits Unions and Ball Adapters
N-10UB Stainless Steel Union, Bored Out, with Nuts and Ferrules
N-10US Stainless Steel Union, Bored Straight Through, with Nuts and Ferrules
N-10UBT Stainless Steel union, Bored Out, PTFE Coated, with Nuts and Ferrules
N-10UST Stainless Steel, Bored Straight Through, PTFE Coated, with Nuts and Ferrules
NI-10UB Alloy 600, 5/8” Tube Union Bored Out, with Nuts and Ferrules
NI-10US Alloy 600, 5/8” Bored straight through, with Nuts and Ferrules
N-10USIB 5/8” Silcosteel®-treated Stainless Steel Bored Union, Nuts and Ferrules included
NTG-10U Glass Filled 5/8” PTFE Tube Union with Nuts and Ferrules
NTG-10UNN Glass Filled PTFE Tube Union without Nuts and Ferrules, Body Only
Material Max TemperatureStainless Steel 650°C (1200°F)PFA Fittings 177°C (350°F)Borosilicate Glass 480°C (900°F)Inconel 980°C (1800°F)Quartz 900°C (1650°F)Viton® O-Rings 260°C (500°F)Graphite Ferrules 980°C (1800°F)Glass Filled PTFE 315°C (500°F)Hastelloy C276 980°C (1800°F)
Recommended Maximum Temperatures
NOZZLE ACCESSORIES
Model Description
NB-3 3/16” Diameter, Twisted Stainless Steel Wire and Nylon Bristles
NB-5 5/16” Diameter, Twisted Stainless Steel Wire and Nylon Bristles
NB-8 1/2” Diameter, Twisted Stainless Steel Wire and Nylon Bristles
NBT-1/2 PTFE Nozzle Brush, 1/2” Diameter, PTFE Barrel and Bristles
Nozzle Brushes
Nozzle Brush Set (NB-SET) One of each type brush from three popular sizes in a convenient carrying tube (sizes 3, 5, & 8).
Model DescriptionVPC-4-16 1/4” Vinyl Push-On Cap, 1/4” OD,
1” Inside Height, Red
VPC-6-16 3/8” Vinyl Push-On Cap, 3/8” OD, 1” Inside Height, Red
VPC-8-16 1/2” Vinyl Push-On Cap, 1/2” OD, 1” Inside Height, Red
VPC-10-16 5/8” Vinyl Push-On Cap, 5/8” OD, 1” Inside Height, Red
Vinyl Nozzle Caps Great for Leak Checks!
Rings
Nozzle Unions
Model Description (Standard 5/8”)10FF-S Stainless Steel, Front Ferrule
10FB-S Stainless Steel, Back Ferrule
10F-GR Graphite High Temp, Single Ferrule
10F-GR-DZ Graphite High, Temp, Ferrule (12 pc) Dozen
NTG-10F Glass Filled PTFE, Single Ferrule
NTG-10F-DZ Glass Filled PTFE, Ferrule (12 pc) Dozen
NI-10FF Alloy 600 Front Ferrule
NT-10BF Alloy 600 Back Ferrule
NT-10F PTFE Single Ferrule 5/8”
NT-10F-DZ PTFE, Single Ferrule, 5/8”, (12 pc) Dozen
Ferrules
NBT-1/2
Tube NutsIndividual Components can be Ordered Separately. Please Call for Pricing.
Integrated Ferrule on Stainless Nozzle for Steel Only
0-113V
N-10 N-10UBNN PL-[_]
PS-[_]N-10BR
(Welded)
IntegratedFerrule
Nozzle Installation for Steel Alloys.
Nozzle Installation for Glass and Quartz. Nozzle Installation for Glass and Quartz.
N-10N-10UBNN
PL-[_] [_]
nB-set
Includes 5/8” Bored Union Body, Nut, Ferrules, Backer Ring and Viton® O-Rings. pk-sp
Small Parts Kit
16
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
Standard Method 5 Probe
Method 5 Probe with Optional Oversheath
Optional OversheathPacking GlandPG-32S
STANdARd METhOd 5 hEATEd PROBESThe Apex Instruments Standard Method 5 Heated Probe Sheath feature 1” diameter sheaths constructed from corrosion resistant stainless steel, modular 3/8” pitot tip, 1/4” stainless steel quick connects, Type-K thermocouples for stack & probe temperature, probe heater and an orsat line, small parts package. Standard lengths are 3’ to 16’. Longer lengths and custom orders are available by request. Order probe liners separately. Probes are ordered according to nominal (liner length). Effective length is one foot less than nominal length.
Replace � with Nominal Length (feet)
Stainless Steel Probe Sheath + Heater PS-�H
Optional with 2” OD Probe Oversheath
PS-�HO2�
Replacement Heater PH-�
Watt
3 3504 3505 4006 4007 4008 4509 475
10 50011 55012 60014 60016 700
Probe Sheaths & heaters
Add “V” to end of part number for 240V option at no extra cost.
The unique design of the Apex Modular Pitot Tip reduces the collection of water droplets in the pitot lines. The lower tube is self-draining while the offset in the upper tube acts as water trap.
Replacement Pitot TipsProduct DescriptionMPT-6-133 Type S Modular Pitot Tip for Oversheath Probes, 3/8”
Stainless Steel, 133mmMPT-6-181 Replacement Pitot Tip for Standard Method 5 Probe Assemblies,
3/8” SS, 181mmMPT-6-181-OFF
Replacement Pitot Tip, 3/8”, Stainless Steel, Offset for use with 47mm Filter holder and PM2.5 Cyclone, 181mm
MPT-6-218 Replacement Pitot Tip, 3/8”, Stainless Steel, Extended for use with Method 5 nozzle and SFA-47 In-Stack filter, Length 218mm
MPT-6-283 Replacement Pitot Tip,3/8”, Stainless Steel, extended for use with PM10 Cyclone and 47mm In-Stack Filter, Length 283mm
MPT-6-320 Replacement Pitot Tip, 3/8”, Stainless Steel, Extended for use with standard Method 5 nozzle and SFA-190, SFA-300, or SFA-2590 In-Stack Filters, Length 320mm
MPT-6-421 Replacement Pitot Tip, 3/8”, Stainless Steel, Extended for use with PM10/2.5 Cyclones and SFA-47 In-Stack Filter, Length 421mm
- 1 foot shorter then effective
Features a tightly wound heating element around a rigid tube. The rigid tube design allows liner replacement without removing the heating element. Actual tube length is 2-3/8” less than nominal length. Apex probe heaters are designed to operate at the method 5 specified temperature of 245°F (+/-25 Degree F). Specify alternate temp requirement if needed at the time of order. The maximum recommended temperature is 260°C (500°F). In extreme applications (probe heaters over 11 feet, long u-cord, long power extension cord), power drops may occur. In these instances, a separate temperature controller is suggested. See Gas Analysis Section, Page 9 for Apex ICH-901 Temperature Controller. Alternate wattage requirement to be specified at time of order.
Method 5 Probe (Tube) heaters
PG-32S
2” Oversheath Packing Gland, 2” NPT Threads, Stainless Steel with PTFE Ferrule. Must be Specified at time of order.
pg-32s
Packing Gland (Optional)
length in mm
M
‘S’ type pitots manufactured in accordance with U.S. EPA Reference Method 2 may be assigned a baseline coefficient of 0.84. Geometric and wind-tunnel calibrations are offered:
PT-CAL-G (Geometric Certification)PT-CAL-W (Wind Tunnel Calibration)
-1 foot shorter then effective
Call For Additional Information
17
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Part Number DescriptionGA-28B10TG PTFE Adapter Glass filled, 28mm Ball to 5/8 inch Tube Fitting, Straight Probe
Liner Ball Adapter. Includes PTFE/glass nut, ferrule and Viton® O-RingGA-28B10TGNN PTFE Adapter Glass filled, 28mm Ball to 5/8 inch Tube Fitting, No Nut
PROBE LINERSStandard Probe Liners are constructed from 5/8” diameter tubing and have #28 ball joint attached. Liners are available in borosilicate glass, quartz, stainless steel, Alloy 600 and PFA; liners with integrated nozzles require a ball joint adapter. Glass and quartz liners with male 14/35” taper joint are available for attaching to the nozzle, eliminating the need for the 5/8” union.
Monorails, page 52
Length in Feet
Standard Probe Liner
Tubing
Probe Liner with Male 14/35 Taper Joint and #28 Ball Joint
Probe Liner with Nozzle(shown with optional #28 ball adapter)
GA-28B10TG
PLN- GTor
PL- QT
N - T
PLS- GN Specify Nozzle Size
Quartz or Glass 14/35 TaperSize
TubingSeamless, for use as probe liner (plain ends)
Part Number DescriptionTTG-10/6 Glass Filled PTFE Probe Liner Material, 5/8 inch OD, 3/8 inch IDTPFA-10/6 Tubing PFA, 3/8 ID x 5/8 OD Heavy WallTS10-035S Seamless 316 Stainless Steel Tubing, 5/8” OD x .035 Wall TI10-035S Seamless Alloy 600 Tubing, 5/8” OD x .035 Wall
MaterialReplace �
with Nominal Length (feet)
Glass
PLN-�G
Stainless Steel
PL-�S
QuartzPL-�Q
Alloy 600
PL-�I
C-276 PL-�C
GT
PLN-�GTQT
PL-�QT
34567891011121416
Probe Liners
Call for Pricing on PLS- GN
*See Accessories for Isokinetic Software
Isokinetic Slide RuleThis device performs Isokinetic Stack Sampling Calculations. The slide rule provides new ∆H settings at a glance.
M5A-1 English Units
M5A-1M Metric Units
Programs included: • Traverse Points Location• Stack Gas Velocity and Volumetric Flow Rate• Stack Gas Moisture Content• Stack Gas Saturation Moisture Content• Ideal Nozzle Size and K-Factor with ∆H Loop• Post-Test Isokinetics• DGM Field Calibration using Critical Orifices
m5a-C
ISOKINETIC CALCULATORS & SPREAdShEET
M5A-C
Isokinetic M5A-C CalculatorThe Casio Graphic Scientific Calculator comes pre-programmed with valuable Isokinetic stack sampling calculations making field calculations quick and easy. Programmed in English and metric units.
Special OptionsPTFE
Adapters
Call For Additional Information
18
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
AIR COOLEd METhOd 5 PROBE
Alloy Method 5 Probe Sheaths are for hot corrosive gases. Includes a 3/8” pitot tip, 1/4” stainless steel quick connects, stack temperature thermocouple with magnesium oxide insulation, and orsat line. The Alloy probe sheaths come standard with Alloy 600 unions for nozzle and pitot (stainless steel optional). Order liners separately. Alternate alloys available, please call for more information and for pricing.
SPECIAL ALLOY METhOd 5 PROBE ShEAThS
Call for current pricing for the following items:• Alloy Liners (PL-��I) • Alloy Sheaths (IPS-��)
- Recommended for High Temperature Applications - Highly Corrosion Resistant
BlowersSBR Blower Assembly, variable speed 93 cfm, connects to SB-2M, also includes hose (110V/60Hz). Add “V” for 240V option.
sBr-93CFm
sBr-93CFm-V
Glass and Quartz Liners Not Recommended Due to Breakage
Part
NumberNominal
Length (feet)APS-4I 4
APS-6I 6
APS-8I 8
Air Cooled Method 5 Probe Assembly with unheated alloy 600 Liner
Call for pricing on additional lengths.
SB2M
SB3
SBR-93CFM
Air Cooled Probe
Air flow in air cooled probes.
Add “V” to end of part number for 240 V at no extra cost.
Air Cooled Method 5 Probes up to 8’ in length, applicable for high temperature sources. Concentric tubular design allows the cooling air to return and exhaust out of the stack. The probe sheath is constructed from stainless steel tubing while the liner, pitot, thermocouple and nozzle union are made from inconel. A variable speed high capacity blower is needed for cooling. Order blower separately.
19
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
MOdULAR SAMPLE CASE ASSEMBLIESApex Instruments Modular Sample Case Assemblies are versatile, lightweight and available in a variety of configura-tions. There are three different filter ovens, and two different risers that can attach to the bottom of the ovens, with four different impinger cases. The impinger cases slide on and off for easy changing of the impinger sets between test runs. Several standard assemblies are available or the individual components can be purchased separately. Please inquire for additional details.
Model description
SB-50 Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M, Riser SBR-10, and Impinger Box SB-3 (holds 4 impingers), 120 V
SB-50-V Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2MV, Riser SBR-10, and Impinger Box SB-3 (holds 4 impingers), 240 V
SB-50/4 Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M, Riser SBR-10, and MId-Sized Impinger Box SB-4 (holds 6-8 impingers), 1`0 V
SB-50/4-V Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M-V, Riser SBR-10, and Mid-Sized Impinger Box SB-4 (holds 6-8 impingers), 240 V
SB-50 Modular Sample Case Assembly
SB-2 heated Filter Box
SB-3
SB-1 Classic Modular Sample Case Assembly Model description
SB-1 Modular Sample Case Includes SB-2 Heated Filter Box & SB-3 Impinger Box, 120V
SB-1V Modular Sample Case (Includes SB-2V Heated Filter Box & SB-3 Impinger Box), 240V
SB-1/4Modular Sample Case Includes SB-2 Heated Filter Box, 110 VAC and SB-4 Impinger Box, holds 6-8 impingers
SB-1/4V Modular Sample Case, includes SB-2 V Heated Filter Box, 240V and SB-4 Impinger Box, holds 6-8 impingers
Heated Filter Box Standard Features• Lightweight aluminum construction• Stainless Steel Probe Clamp• Type K Thermocouple Jack• Probe and Auxiliary Power Jacks• 500 Watt Heater (750 Watt Optional)• 1/2 inch E-Glass Insulation• Mounting Hardware for Riser• Double Doors• Handle/Monorail Attachment• Aluminum Liner• Stainless Steel Latches• Internal Reinforcement
Rigid Arrangement
Monorails, page 52
Flexible Arrangement
SBR-10SB-3
SB-2M Miniatureheated Filter Box
20
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
FILTER OVENSFilter ovens have lightweight powder-coated aluminum-lined panels with stainless steel clamps, hardware and E-Glass insulation thermal insulation. Internal reinforcements reduce flexing of box when testing with long probes. Front and rear doors provide greater accessibility. The handle is designed for attaching to a monorail for easy traversing. The 1” probe clamp may easily be removed from the oven and replaced with differ-ent alternative probe clamps. A SBR-10 Riser is for mounting the impinger case in the rigid arrangement. The SB-2 is the traditional full-size filter oven that is designed for the rigid arrangements for accommodating a cyclone before the filter. The SB-2M Miniature Filter Box and SB-2 Filter Oven will accept standard 2”, 3”, and 4” filter assemblies.
Classic Full Size heated Filter Box has 2 access doors, probe clamp and accepts cyclone. 120 V/60 Hz standard. Dimensions: 23.5” x 9.5” x 9.5”, (60 x 24 x 24 cm), Weight: 16 lbs (7.3 kg).
Add “V” to end of part numberfor 240V/50Hz at no extra cost.
sB-2
sB-2VSB-2
STRAIN RELIEFS FOR SB-2M
GA-104
GA-107-12
The GA-104 connects a 3/8” sample line to the filter exit of the SB-2M oven. Standard comes with #28 socket, thermo-couple, and 1/2” to 3/8” reducing union.
ga-104
The GA-107 strain relief is used with sample lines at the SB-2M during Flexible Method 5 sampling. Includes bracket that attaches to the SB-2M and standard mount with clamp. 1/2” tube.
ga-107-12
The GA-113 strain relief is used spe-cifically with heated sample lines at the SB-2M during Flexible Method 5 sampling. Includes bracket that attaches to the SB-2M and an adjustable Velcro® strap to grip heated sample lines.
ga-113 GA-113
Model description
PC-1 Probe Clamp for 1 inch OD Probe As-semblies
PC-1VU Vertical Probe Clamp for Up-Traverses, 1 inch Clamp
PC-1VD Probe Clamp for Down-Traverse, 1 inch Clamp
PC-2/32 Probe Clamps for 2” Bevel Packing Gland
SB-2M-ST Straight Through Heated Filter Box has two access doors and probe clamp. The Apex SB-2M-ST is the SB-2M with the probe clamp raised so an in-line filter assembly can be used without the need for the cyclone bypass. In addition #28 Stainless Steel Socket with a 3/8” full flow quick-connect is installed on the outlet. Accepts filter assembly GNFA-3-STR. Dimensions: 13.5” x 9.5” x 9.5”, (34.3 x 24 x 24 cm), Weight: 10 lbs (4.5 kg) 120V/60 Hz standard. Add “V” to end of part number for 240V/50 Hz at no extra cost.
sB-2m-st
sB-2m-st-V
SB-2M Miniature heated Filter Box has two access doors and probe clamp; 120V/60 Hz standard. Dimensions: 13.5” x 9.5” x 9.5”, (34.3 x 24 x 24 cm), Weight: 10 lbs (4.5 kg).
sB-2m
sB-2m-V
Add “V” to end of part number for 240V at no extra cost.
SB-2MShown with GA-104 Strain Relief. Order Separately
SB-2M-STSB-2M-ST-V
GA-108
Stainless Steel #28 Socket Adapter with Full Flow 3/8” quick connect and Mounting Bracket, Used on SB-2M Straight Thru To Attach Sample Line.
ga-108
21
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Model Description
SB-50 Modular Sample Case Model 50, (includes SB-2M, SBR-10, & SB-3 & probe clamp), 120V
SB-50-V Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M-V, Riser SBR-10, PC-1, and Impinger Box SB-3, 220V
SB-50/4 Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M, Riser SBR-10, PC-I, and MId-Sized Impinger Box SB-4 (holds 6-8 impingers), 110V
SB-50/4-V Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M, Riser SBR-10, PC-1, and MId-Sized Impinger Box SB-5, 220V
SB-50/5 Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M, Riser SBR-10, PC-I, and MId-Sized Impinger Box SB-5, 110V
SB-50/5-V Modular Sample Case Assembly, Includes Miniature Heated Filter Box SB-2M, Riser SBR-10, PC-1, and MId-Sized Impinger Box SB-5, 220V
Model Description Holds Impingers Dimensions (HxWxD) Weight
SB-3 Impinger Box/Insulated Coolant Reservoir; Model 100 4 9.5” x 9.5” x 13.5” (24.1 cm x 24.1 cm x 34.3 cm) 5 lbs (2.3 kg)
SB-4 Impinger Box/Insulated Coolant Reservoir; Model 150 6 12.5” x 9.5” x 13.5” (31.8 cm x 24.1 cm x 34.3 cm) 6 lbs (2.7 kg)
SB-4SD Impinger Box/Insulated Coolant Reservoir; Divided; Model 150 4 12.5” x 9.5” x 13.5” (31.8 cm x 24.1 cm x 34.3 cm) 6 lbs (2.7 kg)
SB-5 Impinger Box/Insulated Coolant Reservoir; Model 200 8 16” x 9.5” x 13.5” (40.6 cm x 24.1 cm x 34.3 cm) 7 lbs (3.2 kg)
SB-8
GA-100UA-3J
SB-3
Power Box AdapterThe UA-3J connects to umbilical 4-pin circular connector and converts to three straight blade receptacles. Clamps to 1/2” sample line or GA-100 adapter. The UA-3J is used in conjunction with the Compact Method 5, Method 8, Method 17 and in other sampling situations in which power for the probe is not available due to the absence of a heated filter box.ua-3J
Impinger Inlet Strain ReliefThe GA-109 strain relief is used with sample lines at the impinger box when performing Flexible Method 5 sam-pling. Includes bracket that attaches to the impinger box and standard mount with sample line clamp (specify size). Available from 3/8” tube to 2” or 3”.-S is for Velcro version.
ga-109-12ga-109-s
UA-3J-V Adapter, Power, U-Cord, 3 receptacles, 220V Power Box Adapter, Includes 1/2 inch Mounting Clamp and 4 Pin Amphenol to 3 Receptacles.ua-3J-V
UA-3J
UA-3J-VGA-109-12
Sample Case Risers attach to the base of the filter oven for test methods requiring extra height between the filter outlet and the first impinger. The SBR-10 Riser is required for attaching the impinger case to the SB-2M for rigid arrangements. SBR-18 Riser is primarily used for Method 23 sampling when using a vertical condenser.
RISERS
IMPINGER CASES (COLd BOXES)
MOdULAR SAMPLE CASE FRAMEThe Modular Sample Frame (SB-8) with Probe Clamp is an ideal addition for sampling methods that require no heated filter compartment such as Method 8, Method 306 and in-stack filtration methods. The SB-8 secures the probe and impinger case in a rigid manner. The sample frame is made of durable powder coated aluminum with stainless steel probe clamp and impinger case slides.
sB-8
Apex offers four different removable Sample Box Impinger Cases. These cases are constructed from a thicker aluminum to reduce cracking, durable polyethylene foam insulation, and pre-punched foam insert for holding the impinger bottles in place, and have a fold down handle with a rope centering guide and two high strength brackets for mounting strain relief. The cases slide on and off the heated filter box for easy changing of the impingers between test runs. All cases are equipped with a spring-loaded latch to prevent accidental slippage.
SB-3 SB-4 SB-4Sd SB-5Impingers Cases
Model Description Dimensions (HxWxD) Weight
SBR-10 Riser for SB-2M, impinger box adapter, 10” riser with insulated reservoir 9.5” x 9.5” x 10” (24.1 cm x 24.1 cm x 25.4 cm) 10 lbs (4.5 kg)
SBR-18 Riser for MM5, impinger box adapter, 18” riser with insulated reservoir 9.5” x 9.5” x 18” (24.1 cm x 24.1 cm x 45.7 cm) 10 lbs (4.5 kg)
Umbilical (Gooseneck) AdapterThe GA-100 connects the final impinger outlet to the umbilical cable. Standard with #28 socket, thermocouple and 1/2” stainless steel male quick connect. Mounts on Impinger box.ga-100
GA-100
SBR-10 SBR-18
22
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
GN-9A GN-9AO
GN-1GNFA-3
GN-8-18K
GN-2Cyclone Body
(optional)
GN-3Cyclone Flask
(optional)
O-116V #28 Ball Viton® O-Ring
O-126V Impinger Taper Viton®, O-Ring, Top
O-123V Impinger Taper Viton®,
O-Ring, Bottom
GN-11
GN-9A GN-9A
ISOKINETIC GLASSWARE SETSBASIC GLASSWARE SETS Apex Instruments offers a complete line of glassware. Our Standard Glassware features extra heavy borosilicate glass with unground #28 Ball and Socket Joints with O-Ring Seals. Cost effective unground joints are more durable than ground joints and the O-Rings provide a tight, leak-free seal without grease. This set includes all the glassware necessary for one train.
Model DescriptionGN-CGS Basic Method 5 Glassware Set
(3” Filter Assembly)GN-CGS4 Basic Method 5 Glassware Set
(4” Filter Assembly)GN-CGS-Z Basic Method 5 Glassware Set
(3” Filter Assembly) with OZ style ClampsGN-CGS4-Z Basic Method 5 Glassware Set
(4” Filter Assembly) with OZ Style Clamps
Qty Part # Description1 GN-1 Cyclone Bypass, Unground with O-Ring
1 GNFA-� Filter Assembly, Unground Glass, PTFE Frit, Open Style Aluminum Clamp, 3” or 4”
1 GN-8-18K Double “L” Adapter with Type K Thermocouple Assembly, Cap and Silicone Seal
1 GN-9AO Greenburg Smith Impinger with Orifice, Unground
3 GN-9A Modified Greenburg Smith Impinger, Plain, Unground
3 GN-11 U-Tube, Unground Sockets
12 BS28WS #28 Ball Joint Clamp, Generic
Basic Method 5 Glassware Sets
Includes:
Qty Part Description1 GN-8 Double L Adapter, Unground
#28 Sockets1 GN-9AO Greenburg Smith Impinger
with Orifice, Unground3 GN-9A Modified Greenburg Smith
Impinger, Plain, Unground3 GN-11 U-Tube, Unground Sockets
10 BS28WS #28 Ball Joint Clamp, Generic
Method 4 Glassware Sets Model DescriptionGN-CG4 Basic Method 4 (Moisture)
Glassware Set
Includes:
Alternative Styles and Filter AssembliesAre also Available.
23
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
dELUXE METhOd 5 GLASSWARE SET WITh TRANSPORT CASE
NOTE: Set does not include cyclone or cyclone flask. Spare O-Rings are included.
Case dimensions: 25” (63.5 cm) x 19” (48.2 cm) x 23” (58.4 cm)
Full Weight: 63 lbs. (29 kg.) Empty Weight: 39 lbs. (18 kg.)
dELUXE METhOd 5 GLASSWARE SET The deluxe Method 5 Glassware Set with Transport Case (GN-dGS) contains all the glassware plus spares for a full test series. Four filter assemblies cover three sampling runs plus one as a spare. Two full sets of impingers and U-Tubes permit a second run before recovering the first run results. The deluxe glassware set includes spare impingers, U-tubes and Double “L” adapters. The glassware set fits easily into foam lined custom pockets. The sturdy transport case is lockable for secure chain-of-custody. Optional FEP Encapsulated O-Rings are available upon request.
Model Description
GN-DGS Deluxe Method 5 Glass Set w/ Transport Case (3” FA)
GN-DGS4 Deluxe Method 5 Glass Set w/ Transport Case (4” FA)
deluxe Method 5 Glassware Set
Qty Part Description
1 TC-GW2.5 Glassware Transport Case
4 GN-1 Cyclone Bypass, Unground with O-Ring
4 GNFA-� Filter Assembly, Unground Glass, PTFE Frit, Open Style Aluminum Clamp. - Specify Size 3” or 4”
2 GN-8 Double “L” Adapter, Unground Sockets
2 GN-8-18K Double “L” Adapter with Type K ThermocoupleAssem-bly, Cap and Silicone Seal
3 GN-9AO Greenburg Smith Impinger with Orifice, Unground
7 GN-9A Modified Greenburg Smith Impinger, Plain, Unground
8 GN-11 U-Tube, Unground Sockets
30 BS28WS #28 Ball Joint Clamp, Generic
1 GA-3P Filter Tripod
30* O-116S Silicone O-Ring for Grooved #28 Ball
10* O-123V Bottom Viton® O-Ring for Impinger Insert
10* O-126V Top Viton® O-Ring for Impinger Insert
deluxe Method 5 Glassware Set Includes:
* Spares
#28 Ball Joint Sockets are Standard.
Ball Joint Clamps
GLASSWARE ACCESSORIES
Caps & Seals
Product DescriptionO-116V-DZ Viton® O-Ring for
grooved #28 ball, dozenO-116T-DZ TFE Encapsulated
Silicone O-Rings for grooved #28 ball, dozen
O-123V-DZ Viton® O-Ring for bottom groove in Impinger Stem Joint, Dozen
O-126V-DZ Viton® O-Ring for top groove in Impinger Stem Joint, Dozen
#28 Ball Joint & Taper Joints Seals
Product DescriptionBS28WS #28 Stainless steel
ball joint clampRC-29 #28 Stainless steel
ball joint clamp, Pyrex brand
KBS-29 Keck Clip,#29, plastic ball joint clamp
Product Description
GA-GL-18B Bored Cap with hole, #18 threads
GA-18C Solid Cap without hole, #18 threads
GA-GL-18S #18 Silicone Seal Ring, 50 Durometer#18 Threads, 6.5mm Hole Diameter
GA-GL-18ST #18 Silicone with PTFE Seal Ring, #18 Threads,6.5mm Hole Diameter, w/PTFE on half
GA-GL-18T6 #18 Threads Silicone Seal Ring 6.5mmHole Diameter with PTFE on half
GA-GL-18T8 #18/8 PTFE Seal Ring
GA-GL-18/9 #18 Silicone Seal Ring, with PTFE 9 mm to 11 mm
24
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
GLASSWARE FILTER ASSEMBLIES & COMPONENTS
Filter Media, page 46-47
4” Unground Glass, PTFE Filter support, OZ Style Threaded Filter Clamp.
gnFa-4Z
Model Description
GN-2S 2” Glass Filter Inlet, #28 Unground Socket, 90 Degree Bend
GN-2B 2” Glass Filter Outlet, #28 Unground O-Ring Ball
GA-2CA 2” Aluminum Filter Clamp, Open Plate Style
GA-2T 2” PTFE Filter Support with Viton® O-Rings
O-138T FEP Encapsualted O-Ring for GA-2T
O-138V Viton® O-Ring for GA-2T
GA-2P 2” Nylon Filter Tripod
GN-2S-18K3” Unground Glass, PTFE Filter Support, Open Style Aluminum Clamp.
gnFa-3
4” Unground Glass, PTFE Filter Support, Open Style Aluminum Clamp.
gnFa-4
2” Filter Components (55mm)
Model Description
GN-4S 4” Glass Filter Inlet, #28 Unground Socket, 90 Degree Bend
GN-4B 4” Glass Filter Outlet, #28 Unground O-Ring Ball
GA-4CA 4” Aluminum Filter Clamp, Open Plate Style
GA-4CZ 4” Single Thread Filter Assembly, OZ Style
GA-4T 4” FEP Filter Support with Viton® O-Rings
O-156T FEP Encapsulated O-Ring for GA-4T with Hollow Silicone Core
O-156V Viton® O-Ring for GA-4T
GA-4P 4” Nylon Filter Tripod
4” Filter Components (110mm)
Open Style Aluminum Clamp, U-Style with90o inlet and outlet, and #18 threaded joint.
gnFa-3u-18
3” Unground Glass, PTFE Filter Support, Open Style Aluminum Clamp, Straight Through Style.
gnFa-3-str
4 inch Filter Assembly, Unground Glass, Poly Donut Spacer with TC assembly, Dual PTFE Frits, Open Style Aluminum Clamp.
gnFa-4-5g
2” Unground Glass, PTFE Filter Support, Open Style Aluminum Clamp.
gnFa-2
2” U-Style Unground Glass, with 90° inlet & outlet, PTFE Filter Support, Open StyleAluminum Clamp.
gnFa-2u
3” Unground Glass Filter Support, OZ Style Threaded Filter Clamp.
gnFa-3Z
Kit with Thermocouple Assembly.
gnFa-3u-18k
Model Description
GN-3S 3” Glass Filter Inlet, #28 Unground Socket, 90 Degree Bend
GN-3SS
GN-3SS-S 3” Glass Short Stem, Straight Inlet with #28 Unground Socket
GN-3S-18 3” Glass Filter Inlet, #28 Unground Socket, 90 Degree Bend #18 screw joint for Thermocouple
GN-3B 3” Glass Filter Outlet, #28 Unground O-Ring Ball
GA-3CA 3” Aluminum Filter Clamp, Open Plate Style
GA-3CZ 3” Single Thread Filter Clamp Assembly, OZ Style
GA-3T 3” PTFE Filter Support with Viton® O-Rings
GA-3SS 3” Machined Stainless Steel Filter Support Disk with Viton® O-rings, Accepts 82.6 mm filter
O-152T FEP Encapsulated O-Ring for GA-3T
O-152V Viton® O-Ring for GA-3T
GA-3G 3” Glass Filter Disk with Rubberized Edge
GA-3P
3” Filter Components (82.6mm)
3” Stainless SteelFilter Support Disk.
ga-3ss
3” Filter PTFE Disk with Viton O-rings.
ga-3t
3” Glass Filter Disk with Rubberized Edge.
ga-3g
25
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
INdIVIdUAL GLASSWARE ANd ACCESSORIESApex Instruments offers a complete line of glassware featuring Extra Heavy Borosilicate Glass with unground #28 ball and socket joints with O-Ring seals. Unground joints are more durable and price effective than ground joints and the O-Rings provide a tight, leak-free seal without grease. Standard GN-Series Glassware includes Unground O-Ring joints and double O-Ring 45/50 taper joints.
IMPINGER ASSEMBLIES (BOTTLES WITh INSERTS)
GN-9A GN-9AK GN-9AO-M7GN-9AO
403mm15.867in
Model DescriptionGN-9A Modified Greenburg-Smith
(plain stem), 500 ml
GN-9AO Greenburg-Smith (stem with orifice and plate), 500 ml
GN-9AK Knock-out (short stem), 500 ml
GN-9AO-M7 Method 7 (stem with restricted orifice), 250 ml
CYCLONESModel DescriptionGN-2 Cyclone Body, #28, unground
socket and O-Ring ball
GN-3 Cyclone Flask, #28 unground sockets
GN-2RH Cyclone for Mini Hot Box, Reduced Height, includesTeflon-lined #30 Cap
GN-3GN-2 GN-2Rh
Model DescriptionGN-9I Modified Greensburg-Smith O-Ring balls
(plain stem), unground taper joint with double O-Ring seals
GN-91O Greenburg-Smith (orifice stem), O-Ring ball, unground taper joint with double O-Ring seals
GN-91K Knock-out stem, O-Ring balls, unground taper joint with double O-Ring seals
GN-9I
GN-9IK
GN-9IO
387mm15.0 in
INSERTS
Model DescriptionGN-9B Bottle, unground taper joint, 500 ml,
330 mm x 57 mm
GN-9B-1 1.0 liter, 330 mm x 75 mm
GN-9B-1.5 1.5 liter, 330 mm x 100 mm.
GN-9B-2 2 liter, 330 mm x 110 mm
GN-9B-4 4 liter, 330 mm x 140 mm
GN-9B-M7 Method 7 Bottle, 250 ml, accepts GN-9I. 330 mm x 38 mm
BOTTLES
380 mm.13.0 in.
26
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
GFA-2590N-CC
GFA-2590N-CCSUse with these Connections
GFA-2590B-CC
GN-8-18K
GN-1 GN-11 GN-13 GN-8
CONNECTORS
Model DescriptionGN-1 Cyclone Bypass, #28 unground socket and O-Ring BallGN-1-18 #18 Thread for TC (no cap or TC) (not shown)GN-8 Double “L” with #18 Thread for TC. Order
cap and seal separatelyGN-8-18 Double “L” with #18 Thread for TC. Order
cap and seal separatelyGN-8-18K Double “L” withType-K TC assembly,
cap and silicone sealGN-11 U-Tube, #28 unground socketsGN-13 Filter By-Pass, #28 unground socket and O-Ring ball
Glass Cap #28 unground socket.
gn-16
Glass Plug, #28 unground ball with Vitron® O-Ring.
gn-17
Balls and Caps
INdIVIdUAL GLASSWARE ANd ACCESSORIES
Product DescriptionGFA-2590N-CCS GFA-2590 Insert Straight-Thru with
Unground #28Socket to Male Taper Joint, Connects directly to probe. Linear distance socket to taper start 2.5 inches.
GFA-2590B-CC Body for Controlled Condensate Method with ground #28 Ball on outlet
GFA-2590N-CC Insert with “S” Offset, Unground #28 SocketGFA-2590B-CC Body for Controlled Condensate Method with
ground #28 Ball on outletGN-HCCH-A Horizontal Condenser, CCS, Assembly #28
Controlled Condensate Sampling with #11 port for inserting cartridge heater, with Heater and TC assembly, #28 Socket both ends, Water Jacket w/Hose Barbs, TC-well and # 15 Solid Cap
Controlled Condensate Glassware
27
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Model DescriptionGN-20B4 #28 unground O-Ring ball to 1/4” tube
GN-20B6 #28 unground O-Ring ball to 3/8” tube
GN-20B8 #28 unground O-Ring ball to 1/2” tube
GN-20B10 #28 unground O-Ring ball to 5/8” tube
GN-19 #28 unground O-Ring ball to #22 thread. Order cap and seal separately
AdAPTERS
GN-20BGN-18 GN-18B GN-19 GN-20S
Method 17 Glassware
Product DescriptionGFA-2590N* Nozzle Insert, Glass for
GFA-2590 In-StackFilter Assembly, Specify Nozzle Size (N4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 16, 18, 20)
GFA-2590 Thimble Filter, 25x90mm,Binderless Glass Fiber,Tapered, 10/box
GFA-2590B Filter Body, Glass, for GFA-2590 Filter Assembly, 5/8” shank
Product DescriptionG-47N 4 Nozzle I.D. 1/8”
G-47N 5 Nozzle I.D. 5/32”
G-47N 6 Nozzle I.D. 3/16”
G-47N 7 Nozzle I.D. 7/32”
G-47N 8 Nozzle I.D. 1/4”
Product DescriptionG-47N 10 Nozzle I.D. 5/16”
G-47N 12 Nozzle I.D. 3/8”
G-47N 14 Nozzle I.D. 7/16”
G-47N 16 Nozzle I.D. 1/2”
Glass Filter Inlet, 47 mm, with Attached Nozzle
CONdENSERS
Product Description
VGC-9A Condenser Assembly-Includes #7 and #11nylon caps with o-rings and PTFE ferrules.
VGC-12A Condenser Assembly-Includes black nylonbushings, caps o-rings and PTFE ferrules.
INdIVIdUAL GLASSWARE ANd ACCESSORIES
VGC-12AVGC-9A
Model DescriptionGN-18 #28 unground socket to hose barb
GN-18B #28 unground O-Ring ball to hose barb
GN-20S4 #28 unground socket to 1/4” tube.
GN-20S6 #28 unground socket to 3/8” tube
GN-20S8 #28 unground socket to 1/2” tube
GN-20S10 #28 unground socket to 5/8” tube
GFA-2590N GFA-2590BGF-2590 G-47N
28
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
Product DescriptionGNM-HC-18K
GNM-HC Horizontal Condenser, #28 Unground Sockets, Water Jacket Hose Barbs.
GNM-HC-18 Horizontal Condenser, #28 Socket both ends, Water Jacket with Hose Barbs with #18 GL joint for monitoring condenser outlet temperature.
GNM-HC-18F Horizontal Condenser, #28 Socket both ends, #18 joint for monitoring Filter Outlet temperature, Water Jacket with Hose Barbs, Glass Type K thermocouple assembly NOT included.
GNM-T XAD Trap, #28 Unground Socket & O-Ring Ball (Top), Water, Jacket Hose Barbs.
GN-9AKS Knock-Out Impinger Assembly, Unground (for Horizontal MM5)
GN-9AKSA Knockout Impinger Assembly, Unground (for Horizontal MM5)With Long/Short Stems Before Purge on MTHD 202.
Controlled Condensate Method 23 Glassware
GNM-hC GNM-hC-18FGNM-hC-18
Product DescriptionGN-VCHM-M202 M202 Spiral Condenser, #28 Socket
both ends Water Jacket Hose Barbs, High Moisture sources above 15%
GN-VC-M202
GN-9AKS Knock-out Impinger Assembly, Unground, (for HorizMM5)
GNFA-3U-18K 3 inch Filter Assembly, Unground Glass with 90 degree Inlet & Outlet, Open Style Alum Clamp & TC
GN-3S
GN-3S-18
TCA-03X24
TCA-03X24G
Method 202 GlasswareINdIVIdUAL GLASSWARE ANd ACCESSORIES
Product DescriptionGN-9AKSA Knockout Impinger Assembly - 24/40 Taper Unground (for HorizMM5),
Included with Long / Short Stem.
GN-9AKSB Knockout Impinger Bottle - 24/40 Taper Unground (for HorizMM5),Used with Long / Short Stem.
GN-9AKSI Knockout Impinger Stem - 24/40 Taper Short Male, UsedBefore Purge on MTHD 202.
GN-9AKSIL Knockout Impinger Stem - 24/40 Taper Long MaleUsed for Purge on MTHD 202.
GNM-T
GN-9AKSGN-9AKSA
GN-9AKSA
GN-VChM-M202
GN-9AKSIL
GN-9AKSI
GN-9AKSB
GN-9AKS
GNFA-3U-18K
Product DescriptionGN-HCCH
GN-HCCH-A
29
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
BALL ANd SOCKET JOINT AdAPTERSGlass-Filled PTFE
PFA FittingsApex offers both Straight and Elbow PFA Fittings with 1/4” NPT for 1/4”, 3/8” and 1/2” tubing and a ball joint with a 5/8” tube union for adapting to plain probe liners. PFA (Perfluoro-alkoxy) fittings are chemically inert and highly corrosive resistant. Higher mechanical strength than PTFE at elevated temperatures (to 500O).
Apex offers Glass-Filled PTFE #28 Ball and Socket Adapters. Glass fiber fillers are added to Virgin PTFE to improve upon the mechanical properties. Adapters are resistant to deformation under a heavy load and will significantly improve the performance of the seal during a test. Glass-filled adapters are tapped for 1/4” NPT fittings.
Glass Filled PTFE#28 Ball to 1/4” Female NPTga-28B4ntg
Glass Filled PTFE#28 Socket to 1/4” Female NPTga-28s4ntg
Glass Filled PTFE#28 Socket to 3/8” Tube Fitting(Includes Nylon Nut & PTFE Ferrule)ga-28s6tg
Probe Liners, page 17
Glass Filled PTFE#28 Ball to 5/8” Tube Fitting(Includes glass Nut, Ferrule and Viton® O-Ring)ga-28B10tg
Glass Filled PTFE Ferrules5/8” Glass Filled PTFE Ferrule
ntg-10F
5/8” Glass Filled PTFE Ferrule, Dozen
ntg-10F-dZ
Glass Filled PTFE NutGlass Filled PTFE 5/8” Tube Nut
n-10tg
Glass Filled PTFE UnionTube Union, 5/8” Body Only
ntg-10unn
Glass Filled PTFE Union5/8” Union (includes nuts and ferrules)
ntg-10u
PFA Straight Connectors:
PFA Elbow Connectors:
3/8” Tube Fitting to 1/4” MNPT6msC4n-pFa
1/2” Tube Fitting to 1/4” MNPT8msC4n-pFa
1/4” Tube Fitting to 1/4” MNPT4msC4n-pFa
1/2” Tube Fitting to 1/4” MNPT8msel4n-pFa
1/4” Tube Fitting to 1/4” MNPT4msel4n-pFa
3/8” Tube Fitting to 1/4” MNPT6msel4n-pFa
30
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
Stainless Steel Impingers and Accessories are manufactured with #28 Ball and Sockets, 2” diameter and a 500ml capacity. Stainless Steel Impingers are interchangeable with glass impingers for many applications. This kit includes an impinger with Double “L” Inlet Stem, one impinger with restricted inlet U-Stem, two impingers with plain inlet U-Stem, straight inlet stem, five #28 ball joint clamps.
Stainless Steel Ball Adapters#28 Ball to 1/4” FNPTga-28B4n
Stainless Steel Socket Adapter#28 Socket to 1/4” Tube Fittingga-28s4
#28 Socket to 1/4” FNPTga-28s4n
#28 Socket to 3/8” Tube Fittingga-28s6
#28 Socket to 1/2” Tube Fittingga-28s8
#28 Socket to 5/8” Tube Fittingga-28s10
BALL ANd SOCKET JOINT AdAPTERSApex Instruments offers Stainless Steel #28 Ball and Socket Adapters in a variety of sizes, used for connecting to rigid or flexible sample lines. The #28 Ball includes O-Ring (O-116V).
Model Description
S-9A6 Impinger Bottle, 500 ml, 2” diameter, 3/8” Tube Unions, Q-Clamp, No Stem, Stainless Steel
S-9AL Impinger Double “L”, Inlet Stem and #28 Socket and Ball with, Stainless Steel
S-9AO Impinger with Restricted Inlet U-Stem, #28 Socket and Ball, Stainless Steel
S-9A Impinger with Plain Inlet U-Stem, #28 Socket and Ball, Stainless Steel
S-9IL Double “L” Inlet Stem, #28 Socket with Plain End, Stainless Steel
S-9IS Straight Inlet Stem, #28 Ball with Plain End, Stainless Steel
S-9IR U-Stem Inlet, #28 socket on 3/8” Tube with Restricted Tip, Stainless Steel
S-9I U-Stem Inlet, #28 socket on 3/8” Tube with Plain Tip, Stainless Steel
S-9IT Stem Outlet, #28 Ball with O-Ring on 3/8” Tube, Stainless Steel
S-9C2 2” Q-Clamp with Wing Nut, Stainless Steel
40MPU-2 For 2” Q-Clamp, Gasket Buna
S-9B Impinger Bottle Only, 500 ml, Stainless Steel
STAINLESS STEEL IMPINGERS ANd ACCESSORIES
Stainless Steel Impingers and Accessories
#28 Socket 3/8” Elbow Tube Fitting ga-28s4el6
Stainless Steel Socket & Elbow Adapter
Double “L” with #28 Sockets and 1/4” Union for Thermocouple. (TCA-6X24).s-8-4
Stainless Steel Double “L” Connector U-Tube connector with #28 Sockets.s-11
Stainless Steel U-Tube Connector
1/4” Tube Fitting to 1/4” MNPT4msC4n-s3/8” Tube Fitting to 1/4” MNPT6msC4n-s1/2” Tube Fitting to 1/4” MNPT8msC4n-s
1/4” Tube Fitting to 1/4” MNPT 4msel4n-s3/8” Tube Fitting to 1/4” MNPT6msel4n-s1/2” Tube Fitting to 1/4” MNPT8msel4n-s
Stainless Steel Male Elbow Connector
Stainless Steel Straight Adapter
s-8-4kDouble “L” Adapter w/Thermocouple Kit
S-9I
S-9B
S-9IT
S-9IS
S-9IL
BS28WS
S-9AL S-9AO S-9A S-9ATHE SECOND IMPINGER HAS A RESTRICTOR
AT THE BASE OF THE STEM.
See Page 23 for Ball Joint Clamps
Fitting SizeTube Union
4N=NPT (Female)
Set of 4 Stainless Steel Impingers - Stainless Steel Impinger Condenser Assembly, #28 Socket & Ball, Methods 4, 5 and 17. S-5CN
31
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Model Description Qty.SN-5C Stainless Steel Impinger Assembly, #28 Socket & Ball, Includes: SN-9A (3x), SN-9AO (1x),
SN-11 (3x), SN-8-4 (1x), BS28WS clamps (8x), KST-45 Keck Clips (4x). Set
Model Description Qty.SN-9A Stainless Steel impinger Assembly, insert with bottle, straight stem, #28 balls (2), machined cap,
#45 keck clip, 750 ml max capacity. (Discounted Assembly Price).3
SN-9I Stainless Steel Impinger insert only, 3/8” plain stem, #28 balls, machined 1
SN-9B Stainless Steel Impinger Bottle only, 750 ml capacity, with threaded cap 1
KST-45 Keck Clip, size 45, plastic, used on SN-9A & SN-9AO SS impinger assemblies 1
SN-9AO Stainless Steel impinger Assembly, insert with bottle, with 1/16” stem orifice, #28 balls (2), machined cap, #45 keck clip, 750 ml max capacity. (Discounted Assembly Price).
1
SN-9IO Stainless Steel Impinger insert only, orifice stem, #28 balls, machined 1
SN-9B Stainless Steel Impinger Bottle only, 750 ml capacity, with threaded cap 1
KST-45 Keck Clip, size 45, plastic, used on SN-9A & SN-9AO SS impinger assemblies 1
SN-11 U-Tube, #28 Sockets, Stainless Steel 3
SN-8-4 Double “L” Adapter, #28 Stainless Steel Sockets, & 1/4” TU for TCA-6X24 (Sold Separately) 1
BS28WS #28 Stainless Steel Ball Joint Clamp, Generic, with Screw 8
O-Rings O-Ring, Silicon Duro 40, Red 1
Stainless Steel Impingers and Accessories
Stainless Steel Impinger Set
New Stainless Steel Impinger Set and Accessories featuring stainless steel sport bottle with precision or custom fabricated press-in insert. Impingers are manufactured with #28 Ball and Sockets, 2-3/4” diameter and a 750ml capacity. Stainless Steel Impingers are interchangeable with glass impingers for many applications. This kit includes the standard method 5 configuration: 3 plain stem impingers and 1 with an orifice. This new design makes it easier to add ice to your impinger case.
New StAINleSS Steel IMpINger Set AND AcceSSorIeS
SN-9ASN-9ASN-9AOSN-9A
SN-8-4
BS28WSSN-11
KST-45
SN-9I
SN-9B
9-1/2”
SN-9IO
32
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
SPLIT BACK UMBILICAL CABLESplit Umbilical Cables replace Standard Umbilical Cords for added versatility. They are constructed the same way as the Standard Method 5 umbilicals with the sample line and exit thermocouple split to the specified length. Split umbilicals are useful in flexible systems when the filter compartment is separated from impinger box with a flexible sample line such as Method 17, Flexible Method 5 set-ups and Compact Method 5. The umbilical lengths are specified according to overall length. Stainless steel quick connects are standard.
Split -Back Umbilical Cord
Aux
Exit
Sample 1/2” QCStack
To Meter Console
Orsat
Pitot 1/4” QC Probe
Filter
Oven
Amphenol
6 connectors
Filter
Split Umbilical Cord
Split Umbilical CablesModel descriptionUS-30-10 30’ Umbilical w 10’ Split 1/4” Pitot Quick Connects, Stainless Steel Quick Connects
US-60-10 60’ Umbilical w 10’ Split 1/4” Pitot Quick Connects, Stainless Steel Quick Connects
US-90-10 90’ Umbilical w 10’ Split 1/4” Pitot Quick Connects, Stainless Steel Quick Connects
Alternate Lengths Available, Call for Pricing
Umbilical Cord BagLarge Canvas Bag with straps and logo u-Bag
33
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
CLASSIC UMBILICAL CABLES Are lightweight with braided cover. The easily repaired umbilical cable includes one kink-free, wire reinforced sample line, 3 kink-resistant polyethylene lines (2 pitot & 1 orsat line), 6 type K thermocouple extensions, and five conductor electrical cable with 4-pin circular connectors. Thermocouple plugs are colored coded. The sample line has 1/2 inch quick connect and the pitot lines have 1/4 inch quick connects standard (3/8 inch optional). Standard lengths are 30, 60 and 90 feet. U-bag included.
Classic Umbilical CordModel descriptionU-30 30’, Method 5, 1/4” Pitot Quick Con-
nects, Stainless Steel Quick Connects
U-60 60’, Method 5, 1/4” Pitot Quick Con-nects, Stainless Steel Connects
U-90 90’, Method 5, 1/4” Pitot Quick Con-nects, Stainless Steel Quick Connects
Model descriptionU-BAG Large Canvas Bag with straps and logo
QS4/6 Stainless Steel Quick Connects 1/4” Male, 3/8” Female Pitot Quick Connects
QS6 Stainless Steel Quick Connects 3/8” Male and Female Pitot Quick Connects
Optional Accessories
CLASSIC UMBILICAL AdAPTERS
UA-hJ
Power Box Adapter (UA-3J)The UA-3J connects to umbilical 4-pin circular connector and converts to three straight blade receptacles. Clamps to 1/2 inch sample line or GA-100 adapter. The UA-3J is used in conjunction with the Compact Method 5, Method 8, Method17 and in other sampling situations in which power for the probe is not available due to the absence of a heated filter box.
ua-3Jua-3J-V
Probe Power Adapter (UA-hJ)Connects to umbilical 4-pin circular connector and converts to a single female receptacle for the probe power.
ua-hJ
UA-3J UA-3JV
UA-FPheated Filter Box Power Adapter (UA-FP)The UA-FP connects with male plug to the 4-pin circular connector on the filter oven and allows the oven to connect to a standard receptacle.
ua-Fp
heated Filter Box Power Adapter (UA-FP2)Heated Filter Box Power Adapter, Includes one (1) 4 Socket Amphenol to two (2) Male Standard 120V Plugs
ua-Fp2UA-FP2
34
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
UNhEATEd SAMPLE LINES
USL-�-SSTConnects to the
SB-2M
USL-�-QSTConnects to the SFA-82h
USL-�-SSConnects
Probe Liner to Impinger
Unheated Sample LineModel descriptionUSL-�-� USL- � Length in feet / � SST (#28 socket elbow fitting) or QST
(1/2” quick connects/#28 socket elbow)
USL-10-SST 10’ Unheated, PTFE/Stainless Steel Overbraid, w/Thermocouple Assembly, #28 Stainless Steel, Socket Elbow Fittings
USL-10-SS 10’ Unheated Sample Line, 3/8PTFE/Stainless SteelPTFE with SS overbraid, #28 Socket Elbow Fitting Both Ends
USL-15-SST 15’ Unheated, PTFE/Stainless Steel Overbraid, w/Thermocouple Assembly, #28 Stainless Steel, Socket Elbow Fittings
USL-25-SST 25’ Unheated, PTFE/Stainless Steel Overbraid, w/Thermocouple Assembly, #28 Stainless Steel, Socket Elbow Fitting
USL-10-QST 10’ Unheated, PTFE/Stainless Steel Overbraid, 1/2” Female Stainless Steel Quick Connect, w/Thermocouple Assembly, #28 Stainless Steel Socket Elbow
USL-15-QST 15’ Unheated, PTFE/Stainless Steel Overbraid, 1/2” Female Stainless Steel Quick Connect, w/Thermocouple Assembly, #28 Stainless Steel Socket Elbow
USL-25-QST 25’ Unheated, PTFE/Stainless Steel Overbraid, 1/2” Female Stainless Steel Quick Connect, w/Thermocouple Assembly, #28 Stainless Steel Socket Elbow
Unheated Sample Line jumpers are used between the probe liner or filter and the first impinger in “flexible” sampling arrangements. Jumpers are available in various lengths and configurations. Stainless steel overbraid 3/8” ID PFA tubing is standard.
hEATEd SAMPLE LINES (JUMPERS)Heated Sample Line Jumpers are used when source sampling site has limited access and insufficient space for a traditional, rigid sample train. Apex Instruments manufactures short heated sample lines/jumpers for use between the heated filter assembly and the first impinger inlet. For all Self-Regulating Heated Sample Lines, the National Electric Code requires ground fault protection of equipment for each branch circuit supplying electrical heating cables or devices.
heated Sample Line JumperHSL-�-� hSRL - � Diameter of each sample or cal gas tubing (4 = 1/4”, 6 = 3/8”, 8= 1/2”)
- � Length of line in feetHSL-6-10 10’, 3/8” PFA Sample Line, with Insulation & Protective Sleeve, 120V, ~ 20 Watts / Per Ft.
HSL-6-15 15’, 3/8” PFA Sample Line, with Insulation & Protective Sleeve, 120V, ~ 20 Watts / Per Ft.
HSL-6-20 20’, 3/8” PFA Sample Line, with Insulation & Protective Sleeve, 120V, ~ 20 Watts / Per Ft.
HSL-6-25 25’, 3/8” PFA Sample Line, with Insulation & Protective Sleeve, 120V, ~ 20 Watts / Per Ft.
HSL-6-10V 10’, 3/8” PFA Sample Line, with Insulation & Protective Sleeve, 240V, ~ 20 Watts / Per Ft.
HSL-6-15V 10’, 3/8” PFA Sample Line, with Insulation & Protective Sleeve, 240V, ~ 20 Watts / Per Ft.
HSL-6-20V 20’, 3/8” PFA Sample Line, with Insulation & Protective Sleeve, 240V, ~ 20 Watts / Per Ft.
HSL-6-25V 25’, 3/8” PFA Sample Line, with Insulation & Protective Sleeve, 240V, ~ 20 Watts / Per Ft.
Add “V” to end of part number for 240V at no extra cost. Temperature Controller Required.
35
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
heated Sample Lines/Jumpers
STRAIN RELIEFMini heated Filter Box Sample Line Strain ReliefThe GA-107 strain relief is used with sample lines at the SB-2M during Flexible Method 5 sampling. Includes bracket that attaches to the SB-2M and standard mount with sample line clamp (specify size).
Model description
GA-107-9 Line Adapter (for SB-2M), includes Bracket and 3/8 inch ID Sample Line Clamp
GA-107-12 Line Adapter (for SB-2M), includes Bracket and 1/2 inch ID Sample Line Clamp
GA-107-32 Line Adapter (for SB-2M), includes Bracket and 1-1/4 inch ID Sample Line Clamp
GA-107-50 Line Adapter (for SB-2M), includes Bracket and 2 inch ID Sample Line Clamp
GA-107-57 Line Adapter (for SB-2M), includes Bracket and 2-1/4 inch ID Sample Line Clamp
The GA-113 strain relief is used specifically with heated sample lines at the SB-2M during Flexible Method 5 sampling. Includes bracket that attaches to the SB-2M and an adjustable Velcro® strap to grip heated sample lines.
GA-113
GA-107-� GA-113
NEW SELF-REGULATING hEATEd SAMPLE LINES (JUMPERS)Apex’s New heavy duty Self Regulating heated Sample Lines are custom manufactured to be rugged, lightweight and flexible. The heater cable is self-regulating and maintains the sample line at a constant temperature up to 250°F (120°C) over the entire length of the line. The standard core is typically comprised of PFA tubing, 3/8” for the sample and 1/4” for the calibration gas. The heated core is insulated with several layers of braided lightweight Pyron OPF yarn that will not burn or conduct electricity. The braided construction provides extreme flexibility, strength, and protects the heater cable by minimizing movement. The bundle is protected by a tough high temperature silicone coated fiberglass sleeving.
Advantages/Features• Rugged, Lightweight & Flexible• Suitable for Permanent Installations or Portable use • Braided Construction with High Temperature Jacket• High Quality Components
Options/Accessories• Replaceable core, (flexible conduit) pass through power and thermocouples for the probe oven heaters.• Cam-Lock fittings for easy installation and serves as a strain-relief.
Heater Cable 15 w/ft @ 50°F (10°C) 49 w/meter
Supply Voltages: 120 or 220Vac
Maintenance Temperature: Up to 250°F (120°C)
Maximum Exposure Temperature:
366°F (185°C)
Cable Specifications
Circuit Breaker SizeMaximum Length (Ft.) 120VAC 240VAC
15 amp 80
20 amp 110
30 amp 135
Circuit Breaker Size Vs. Maximum Length in Feet
160
215
270
36
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
METhOd 4 SAMPLING TRAIN
Flexible Method 4 Arrangement
Rigid Method 4 Arrangement
Method 4 Determination of the Moisture Content of Stack Gas Summary: Stack gas is extracted at constant rate (less than 21lpm) and a minimum volume of 600 liters. Moisture is removed from the sample stream, and measured volumetrically or gravimetrically.
sk-m4
sk-m4-V
Part DescriptionPC10-4S CEM IRM Probe, 4ft,
Stainless Steel Sheath,5/8” Stainless Steel Liner.
PLS-4S-QCF6 Probe Liner, 4ft, SS, w/Full Flow, 3/8” QC.
USL-15-QS 15ft Unheated Sample Line, PTFE with SS Overbraid, #28 Socket Elbow Fitting and Full Flow 3/8” QCF Elbow Fitting.
SB-8 Probe Clamp FrameGN-CG4 Method 4 Glassware Set,
Unground Joints.SB-3 Impenger box, Model 100,
Insulated Cooltant Reservoir, Holds 4 Impingers
GA-100 Sample Case AdapterUS4-25-10 U-Cord, Method 4, 25”,
Splitback 10ft.
Method 4 Individual Accessories
Meter Consoles, page 4-11
Meter Console Sold Separately
XC-40 Meter ConsoleRecommended forMethod 4 Testing
37
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
BASIC-PLUS METhOd 5For a source sampling company to get started sampling for particulates (U.S. EPA Reference Method 5), Apex recommends a combination of equipment that can be configured for both rigid and flexible set-ups.Select your METER CONSOLE (see page 8-10)Select your SAMPLE PUMP (see page 12 - 13)
sk-m5Bp
sk-m5Bp-V
Basic Method 5 Includes:• Stainless Steel Nozzle Set• 6-ft Probe with Heater• 1 Stainless Steel Probe Liner, 3 Glass Probe Liners• 30-ft Split U-Cord• 15-ft Unheated Sample Line• Hot & Cold Box Assembly with Riser• Sample Frame for Cold Box (Flexible Config.)• Strain Reliefs• Basic Glassware Set (1 sample run configuration)• Filter Paper• Brushes (Probe & Nozzle)• Calculator (programmed for Method 5)
dELUXE-PLUS METhOd 5The professional source sampling company must be prepared for a wide variety of con-ditions and locations. Apex recommends the “Deluxe Plus” system, which can be used in both rigid and flexible configurations. Even with the classic rigid arrangement, the ad-ditional glassware allows you to have pre-measured and filled impingers, pre-weighed filter assemblies, and minimum turnaround time between runs. The flexible arrange-ment is effective for challenging environments like vertical traverses and space-limited sources. After selection of a meter console and external sample pump, the Deluxe-Plus system provides all of the components listed in the above Basic-Plus system.
Schematic of Method 5 Flexible Sampling Train
Schematic of Method 5 Rigid Sampling Train
deluxe-Plus Method 5:• Glass Nozzle Set• 3-ft & 9-ft Probe Assemblies with • Stainless Steel & Glass Probe Liners• 60-ft Split U-Cord• 2.5 Sets of Glassware Plus Carrying Case• 4 Monorail Assemblies (9-ft & 12-ft)• Transport Case for a Meter Console• Calibrated Orifice Set
sk-m5dp
sk-m5dp-V
38
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
COMPACT METhOd 5The Apex Compact Method 5 Sampler Kit features an independently Heated Stainless Steel Filter Assembly (SFA-82H) that connects directly to a standard Method 5 probe. It does not require a separate heated filter compartment, and utilizes a flexible sample line, and a split umbilical cord with power adapter, to allow sampling in space-limited areas. The standard glass impingers have been replaced with Stainless Steel Impingers (S-5CN) to eliminate glass breakage. Three filter assemblies are recommended to speed up the turn around time between consecutive runs. Add “V” to end of part number for 240V option at no additional cost.
sk-Cm5
sk-Cm5-V
STAINLESS STEEL hEATEd FILTER ASSEMBLYThe Apex Instruments Heated Stainless Filter Assembly (SFA-82H) is for sampling particulates from space-limited industrial sources. The filter assembly has a two piece threaded clamping ring with an integral 300 watt ring heater . A Viton® O-Ring seals the 82.6 mm filter and prevents sample bypass. It has stainless steel inlet, outlet and a PTFE filter support screen (GA-3T). The inlet plate comes with a 5/8” tube union for swaging directly to a plain probe liner. The outlet plate has 3/8” female NPT connection and a male 3/8” full flow quick connect. The mating female quick connects with the thermocouple, which is supplied with the Unheated Sample Line (USL-�-QST) or SFA-82-QCF6, may be ordered separately. There is a thermal insulated blanket supplied with each unit. An unheated version is also available without the integral heater and blanket. Add “V” to end of part number for 240V at no extra cost.
SFA-82 (unheated)sFa-82hsFa-82hVsFa-82-qCF6sFa-82-Bkt
SFA-82hDepending upon the source, it may be possible to combine
Method 5 and Method 8 into the same train.
SK-CM5 Kit• Heated Filter Assemblies (3)• Probe Sheath with Heater • Stainless Steel Probe Liner• Impinger Box • Impinger Inlet Strain Relief• 60’ Split Umbilical Cord• Unheated Sample Line with Stainless Steel Overbraid• Power Box Adapter • Umbillical Adapter • Stainless Steel Nozzle Set• Stainless Steel Impinger Assembly• PTFE Coated Glass Fiber Filters
Schematic of U.S. EPA Method 5 Compact Sampling Train
SFA-82-QCF6
SFA-82-BKT
39
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
METhOd 5GMethod 5G Determination of Particulate Matter Emissions from Wood Heaters (Dilution Tunnel Sampling Location). The exhaust from a wood heater is collected with a total collection hood, and is combined with ambient dilution air. Particulate matter is withdrawn proportionally from a single point in a sampling tunnel and is collected on two glass fiber filters in series.
gnFa-4-5g
Components Include:4” Filter Assembly, Unground Glass #28 Ball/Socket, Poly Donut Spacer with ThermocoupleAssembly, Dual PTFE Filter Supports and Open Style Aluminum Clamp.
ALTERNATE METhOd 5I FILTER ASSEMBLY (Straight) Same Application as Method 5IStraight version of SGFA-47-5I, for use with SB-2M-ST, straight through heated filter box.
sgFa-47-5is
SGFA-47-5IS
SGFA-47-5I
GNFA-4-5G
METhOd 5I The METHOD 5I SAMPLING KIT is similar to Basic Method 5, except for the addition of the 5I Holder (SGFA-47-5I) and is designed for the determination of low-level particulate matter (PM) emissions from stationary sources. Method 5I is most effective for PM catches less than 50 mg and is valid for performing correlation of manual PM measurements to PM con-tinuous emission monitors or determining PM emissions from low-level sources such as turbines. Add “V” to end of part number for 240V at no extra cost. After selecting a Method 5 Meter Console and an external sample pump in conjunction with a Method 5 kit, add a Method 5I Holder.
The 5I Filter Holder inlet is constructed of Borosilicate Glass to hold a 47mm glass fiber filter with a wafer-thin stainless steel filter support and a Viton® O-Ring. The assembly is wrapped with PTFE tape for weighing, averaging less than 35 grams, providing a positive seal against leakage. Method 5I 47mm Filter Assembly with Glass Inlet & SS Outlet, with 2 45 deg bends.
sgFa-47-5i
40
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
Controlled Condensate is an alternative to EPA Method 8 for determining sulfuric acid emissions. Sulfuric acid vapor or mist and the sulfur dioxide are separated, by controlling the condensation based on difference in dew points, and both fractions are measured separately by the barium-thorin titration method. Controlled condensation method is the primary sampling and analytical tool for quantifying sulfuric acid emissions from stationary sources. The method is based upon the selective condensation of sulfuric acid from a gas stream by means of a water cooled condenser. The major advantage of the condensation method is that it provides reliable reproducible SO3 and SO2 values with minimal interference from high SO2 concentrations. There are several versions of the method. Option “V” is added for 240V.
sk-CC
sk-CC-V
METhOd 8
Method 8 Sampling Kit
Part Description
SB-8 Sample Frame with Probe Clamp
UA-3J Power Box Adapter
GNFA-2U 2” Filter Assembly,Unground Glass with 90° Inlet and Outlet,Open Style Alum Clamp
METhOd 8 RECOMMENdEdACCESSORIES
CONTROLLEd CONdENSATEConditional Test Method CTM-13
Quartz Liner Available
Glass Liner
GFA-2590#-CC SB-2M-STCC
Sampling Kit Available
The Method 8 Sampling Kit is used with either the XC-522 or XC-572 Meter Console and an external sample pump for the determination of sulfuric acid mist and sulfur dioxide emissions from stationary sources. U.S. EPA Reference Method 8 was originally developed to test emissions from sulfuric acid plants but has been adapted to sample emis-sions from sulfur dioxide sources. Call for details on Flex-ible Arrangements. Add “V” to end of part number for 240V at no extra cost.
Schematic of EPA Method 8 Sampling Train
UA-3J
GA-100
SB-3SB-8
PS- H PLN- GGlass Lined Probe
Glass NozzleNG-
US- -10
772 Watts Heater
41
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Schematic of EPA Method 17 Flexible Sampling Train
Schematic of U.S. EPA Method 17 Rigid Sampling Train
In Method 7C and 7d an integrated sample is passed through a series of full-size orifice impingers that contain an alkaline-potassium permanganate solution. The sample rate is between 400 and 500 cc per minute, normally three one hour samples are collected per test. The MC-623 is the console of choice, however, a low flow orifice adapter is offered for converting the XC-572 Method 5 source sampler console for low flow sampling. The Method 7C sample is analyzed colorimetrically and for Method 7D analysis is by ion chromatography. Please inquire for additional details. Add “V” for 220VAC option.
Ck-m7Cd
METhOd 7C and 7d
Model descriptionPC10-3G 3 ft CEM Probe Assembly, 5/8” Glass liner, 110 VAC
PLN-3G 3 ft Glass Probe liner, 5/8” OD with unground #28 grooved ball
GN-8 Double”L” Adapter, #28 unground sockets
GN-11 U-Tube, #28 unground sockets
GN-9AO-M7 Impinger Assembly, Stem with Orifice, 250 mL, unground O-ring joints
Method 7 Accessories
PC10-3G
GN-9AO-M7GN-9A
SB-3
GN-8GN-11
SB-8
Method 17 Sampling Kit Components Include:• In-stack Filter Assembly
• Glass Fiber Thimbles
• Method 5 Probe Sheath with Tube Heater
• Method 17 Probe Liner w/ 3/8” Full Flow Male Quick Connects
• Unheated Sample Line with PFA Over braid
• 30’ Split Umbilical Line
• Power Box Adapter
• Sample Case Adapter
• Impinger Inlet Strain Relief
• Impinger Box, Insulated Coolant Reservoir
• Stainless Steel Nozzle Set
• Stainless Steel Impinger Assembly
sk-m17psk-m17p-V
METhOd 17 PLUS (RIGId & FLEXIBLE)The Apex Instruments Method 17 Sampling Kit is a convenient package for sampling particulate matter. Multiple fitting arrangements and filter assemblies are available with an in-stack filter. Add “V” to end of part number for 240V at no extra cost.
GN-9A Impinger Assembly, Plain Stem, 500 mL, unground O-ring joints, modified Greenburg-Smith
GA-100 Umbilical Adapter (Gooseneck) , #28 Socket with thermocouple, mounting bracket, 1/2” Male quick connects
SB-3 Impinger Box/Insulated Coolant Reservoir Model 100, holds 4 impingers
SB-8 Modular Sample Frame with Probe Clamp and Impinger Box Slides
42
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
SFA-4(Nozzles not included)
INTEGRATEd IN-STACK FILTER ASSEMBLY KIT The SGFA-47NK In-Stack Filter assembly kit features the unique design combination of borosilicate glass 47mm filter inlet with integrated nozzle, allowing the option to weigh the glass fiber filter media individually for Method 17 or very similar to Method 5I by weighing the combined nozzle, filter media with a support, O-Ring and PTFE Tape. The kit includes the standard array of seven nozzle sizes from 1/8” to 1/2”.
sgFa-47nk
METhOd 17 IN-STACK FILTER ASSEMBLIES
GLASS IN-STACK FILTER ASSEMBLIESThe Apex Instruments GFA-2590 Thimble Holder is constructed completely from borosilicate glass for use with Conditional Method for Ammonia (CTM-027) and accepts tapered 25 x 90mm thimbles, specifically manufactured for stack sampling. Does not require O-Rings, for testing at higher temperatures. The borosilicate glass withstands temperatures up to 480°C (900°F).
Nozzle Insert - Replace � with nozzle diameter. (Sizes 4-16). Call for additional sizesGFA-2590N�
Filter Body - 5/8” Glass Filter BodygFa-2590B
Metal Taper Joint Clamp - A durable nickel plated steel clip that securely holds the conical joint under pressure to withstand temperatures of up to 500°C (932°F).ktm-29
In-Stack Filter Assembly using a 47 mm diameter Filter Element.sFa-47
In-Stack Filter Assembly using 19mm x 90 mm Thimble Filter Element.sFa-190In-Stack Filter Assembly using 30mm x 100 mm Thimble Filter Element.sFa-300
In-Stack Filter Assembly using 25mm x 90mm Thimble Filter Element.sFa-2590
Inconel Version SFA-47INCO...call for price
Filter Inlet 47 mm Glass Filter Inlet with Integrated Nozzle. Replace � with nozzle diameter.
Part descriptionO-128V Viton® O-Ring for SFA-2590 (450 °F)
O-324S Silicone O-Ring for SFA-300 (500 °F)
O-324G Graphite O-Ring for SFA-300 (1000 °F)
O-324V Viton® O-Ring for SFA-300 (500 °F)
Q4213 Viton® Quad Ring for SFA-190 (450 °F)
O-223V Viton® O-Ring, 47 mm for SFA-47 (450 °F)
O-223H High Temperature Stainless Steel O-Ring for SFA -47
SF-TT20 PTFE Thrust Ring for SFA-47 Filter Assembly
Replacement Seals
Filters and Thimbles, page 46
GFA-2590K In-Stack Thimble holder Kit - Includes a selection of the seven most commonly used nozzle inserts from 1/8” to 1/2” and one housing. Kit is conveniently packaged in a foam-lined carrying case for protection. The thimble holder connects directly to the end of the probe with a 5/8” tube union.gFa-2590k
Nozzle Size
GFA-2590N □ Nozzle Insert GFA-2590B
Filter Body
5/8” ShankKTM-29 CLIP
Product Glass Filter Inlet Integrated Nozzles
G-47N-4 47mm, with Attached Nozzle, Nozzle I.D. 1/8”
G-47N-5 47mm, with Attached Nozzle, Nozzle I.D. 5/32”
G-47N-6 47mm, with Attached Nozzle, Nozzle I.D. 3/16”
G-47N-7 47mm, with Attached Nozzle, Nozzle I.D. 7/32”
G-47N-8 47mm, with Attached Nozzle, Nozzle I.D. 1/4”
G-47N-10 47mm, with Attached Nozzle, Nozzle I.D. 5/16”
G-47N-12 47mm, with Attached Nozzle, Nozzle I.D. 3/8”
G-47N-14 47mm, with Attached Nozzle, Nozzle I.D. 7/16”
G-47N-16 47mm, with Attached Nozzle, Nozzle I.D. 1/2”
Call for Pricing of Quartz Components
43
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Schematic of Method 23 Sampling Train
METhOd 23 dELUXE PLUSThe Apex Instruments Method 23 (Modified Method 5) Source Sampler Kit is utilized for Method 23 determination of dioxins and furans (D/F’s) and/or Method 0010 Determination of Semi-Volatile Organic Compounds. The sampling train is identical to the standard Method 5 system with the addition of a water-cooled glass condenser and an XAD absorbent module followed by a knockout impinger. Additional glassware configurations are available. Please call for information.
Select Meter Console and External Pump for M23 then add a kit. Add “V” to part number for 240V option at an additional cost.
sk-m23dp
sk-m23dp-V
Product Conversion Accessories
SB-4 Impinger Box/Insulated Coolant Reservoir Model 150, Holds 8 Impingers
MM5-P Submersible Coolant Pump, 120V
GN-16 Glass Cap #28 Socket, Unground, to Seal XAD Trap
GN-17 Glass Plug #28 Ball, Unground, to Seal XAD Trap
KBS-29 Clip, Knock, Plastic out Impinger, Unground
TL-7/5 Latex Tubing, 7/16 OD, 5/16 ID, Natural Color, Per Foot
Method 23 Individual Accessories
Product description
GNM-HC Horizontal Condenser, #28 Unground Sockets, Water Jacket, Hose Barbs
GNM-VC Vertical Condenser, #28 Unground Sockets, Water Jacket Hose Barbs
GNM-T XAD Trap, #28 Unground Socket nd O-Ring Ball (Top), Water, Jacket Hose Barbs
GN-9AKS Knock-Out Impinger Assembly, Unground (for Horizontal MM5)
Method 23 Glassware
Requirements:• Borosilicate Glass or Quartz Nozzles and Probe Liners are recommended.• Wrap XAD sorbent module with aluminum foil to shield from radiant heat and ultraviolet rays that dechlorinate the D/F isomers.• Sealing greases are not allowed. FEP O-Ring seals are recommended and may be required by some agencies.• Flexible train requires heated flexible sample lines.
Coolant Pump OptionsProduct Description
MM5-P Submersible Coolant Pump, 110V
MM5-PM Mini Submersible Coolant Pump, 110V
MM5-P220 Submersible Coolant Pump, 220V
MM5-P MM5-PM
M23 Sampling Train
Method 23 Source Sampler Kit Components:• 6’ Probe with Heater• Glass Probe Liners (3)• Glass Nozzle Set• Hot/Cold Box/Riser• 30’ Split-Back Umbilical • Glassware, Deluxe Set
• Horizontal Condensers (2)• XAD Traps (8)• Submersible Recirculating Pump• Probe and Nozzle Brushes• Programmed Calculator
44
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
METhOd 26A – hCl
M26A Sampling Train
The Apex Instruments Method 26A Sampling Train is used for determination of hydrogen halide and halogen emis-sions. Method 26A is the isokinetic alternative to Method 26. This method is particularly suited for sampling sources controlled by wet scrubbers emitting acid particulate matter. The method requires a Method 5 sampling train with the use of additional impingers, reagents and PTFE coated glass fiber filter media. Please call for more information. Add “V” to end of part number for 240V at no additional cost.
Product Conversion Accessories
SB-4 Impinger Box/Insulated Coolant Reservoir Model 150, Holds 8 Impingers
NG-SET Set of 7 Glass Nozzles - Sizes 4,6,8,10,12,14&16, Includes Case and Three 5/8” Glass Filled PFA Ferrules
NBT-1/2 Nozzle Brush, 1/2” diameter, PTFE Bristles
PBX-10T 10 foot Flexible PTFE Probe Brush Extension, Brush not Included
PBT-5/8 PTFE Probe Brush Tip (PTFE Barrel and Bristles), 5/8 inch Bristle Diameter
GN-9AK Knock-Out Impinger, Short Stem, 500ml, Unground O-Ring Joints
GN-9AO Impinger Assembly, Stem with Orifice & Plate, 500ml, Unground O-Ring Joints, Greenburg-Smith
GF-3TPG 82mm PTFE Coated Glass Fiber Filters - Hydrophobic, Low absorption of acid gases such as SOX or NOX . 50/box (MFS PG60)
Method 26A Recommended Accessories
Schematic of Method 26A Sampling Train
When stack temperatures exceed 210oC (410oF) a one-piece glass nozzle/liner assembly is recommended.
45
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
The METHOD 29 determination of metal emissions from hazardous waste incinerators involves a modification of the Method 5 train. The sampling train is the same as a Method 5 particulate train with the addition of up to three impingers to enhance the collection of metals of interest. The impinger train requires the SB-4 impinger case, glass nozzles, probe liners and non-metallic union. The method has been validated for the collection of 17 different metals.
Add “V” to end of part number for 240V option at no additional cost.
METhOd 29 – MULTIPLE METALS
Schematic of Method 29 Sampling Train
The standard glass filters are replaced with low background quartz filters. The impinger solutions are specific for different metals. Recovered samples are digested and appropriate fractions are analyzed by various means; inductively coupled argon plasma emission spectroscopy (ICPES), atomic absorption spectroscopy (AAS) or graphite furnace AAS, depending upon sensitivity required or the matrix effects on the specific analyte.
M29 Sampling TrainProduct Conversion Accessories
SB-4 Impinger Box/Insulated Coolant Reservoir Model 150, Holds 8 Impingers
NG-SET Set of 7 Glass Nozzles - Sizes 4,6,8,10,12,14&16, Includes Case and Three 5/8” Glass Filled PFA Ferrules
GF-3QR 3 inch Quartz Fiber Filters-100/box (MFS QR100 82mm)
GN-9AK Knock-Out Impinger, Short Stem, 500ml, Unground O-Ring Joints
GN-9A Modified Greenburg-Smith Impinger (Plain), Unground
GF-3Q 3 inch Quartz Fiber Filters-25/box (Pallflex 8.26cm)
PBT-5/8 PTFE Probe Brush, Extension, 10 Foot Flexible (Brush Not Included)
PBX-10T PTFE Probe Brush, 5/8” diameter, 4” length, 8-32 thread
NBT-1/2 Nozzle Brush, PTFE, 1/2 inch
Method 29 Recommended Accessories
46
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
In the Ontario-Hydro Method (ASTM D6784-02) a sample is withdrawn from the flue gas stream isokinetically through probe/filter system, maintained at 120OC (250OF) or the flue gas temperature (whichever is greater), followed by a series of impingers in an ice bath. Particle-bound mercury is collected in the front half of the sampling train. Oxidized mercury is collected in impingers containing a chilled aqueous potassium chloride solution. Elemental mercury is collected in subsequent impingers (one impinger containing chilled aqueous acidic solution of hydrogen peroxide and three impingers containing chilled aqueous solutions of potassium permanganate). Samples are recovered, digested, and then analyzed for mercury using cold-vapor atomic absorption (CVAAS) or flourescence spectroscopy (CVAFS). The scope of the method applies to determination of elemental, oxidized, particle-bound and total mercury emissions from coal-fired stationary sources with concentrations ranging from approximately .05 to 100 ug/dscm. The sample train is similar to EPA Method 5.
ONTARIO-hYdRO – METhOd (ASTM d6784-02) MERCURY
Schematic of Ontario-hydro Method Sampling Train
Product Conversion Accessories
SB-4 Impinger Box / Insulated Coolant Reservoir Model 150, Holds 8 Impingers
NG-SET Set of 7 Glass Nozzles - Sizes 4,6,8,10,12,14&16, Includes Case and Three 5/8” Glass Filled PFA Ferrules
BS28WS #28 Ball Joint Clamp (Generic), Stainless Steel
NBT-1/2 Nozzle Brush, 1/2 inch diameter, PTFE Bristles
PBX-10T 10 foot Flexible PTFE Probe Brush Extension, Brush not Included
PBT-5/8 PTFE Probe Brush Tip (PTFE Barrel AND PTFE Bristles), 5/8 inch Bristle Diameter
GN-9A Greenburg-Smith Impinger (with orifice), Unground
GN-9AO Impinger Assembly, Stem with Orifice & Plate, 500ml, Unground O-Ring Joints, Greenburg-Smith
GN-11 U-Tube, #28 Unground Sockets
GF-3Q 3” Quartz Fiber Filters, 25/Box
Ontario-hydro Recommended Accessories
Ontario-hydro - Mercury Sampling Train
47
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Method 201A applies to the in-stack measurement of particulate matter (PM) emissions equal to or less than an aerodynamic diameter of nominally 10 microns (PM10) and or 2.5 microns from stationary sources. A gas sample is extracted at a constant flow rate through Apex instruments cyclone, which separates PM greater than PM10.. PM .less than PM10 is collected on the in-line filter. In order to maintain a cut size of 10 microns in the cyclone, the flow rate must be maintained at a constant, discrete value during the run. Apex cyclones meets the specifications of Method 201A and allows use of the equations in Method 201A to calculate the constant sample flow rate.
pm2-k
PARTICLE SIZING - PROPOSEd MOdIFICATION METhOd 201A
Packing List
Introducing PM1 CycloneApex Instruments now offers a cyclone designed for sampling very fine particulate matter in the 1.5 to 0.5 micron range. The cyclone is based on the cyclone “V” from the Multi-stage cyclone system designed and calibrated by Southern Research Institute under contract for the EPA. The design has been modified to accept the nozzles from the PM 2.5 cyclone, which has been expanded to a set of 12 different size nozzles. The sample flow rate must be maintained, in which the constant rate determines the actual “D50” cut-point. The cyclone is followed by a 47 mm filter assembly. Quartz or PTFE coated glass fiber filters should be used to minimize reactivity with the flue gas. The cyclone and nozzles are constructed from grade 316 stainless steel with Viton o-rings. Other materials are available upon request for corrosive or high temperature applications.
pm1-k
Product Size
PM2-N1 .125 Size 1
PM2-N2 .138 Size 2
PM2-N3 .156 Size 3
Apex Expanded Nozzle SetPM2-NS Nozzle Set Includes 1 Each
Product Size
PM2-N7 .216 Size 7
PM2-N8 .234 Size 8
PM2-N9 .253 Size 9
Product Size
PM2-N4 .172 Size 4
PM2-N5 .188 Size 5
PM2-N6 .200 Size 6
PM2-NS Nozzle Set Includes 1 Each
Product Size
PM2-N10 .274 Size 10
PM2-N11 .296 Size 11
PM2-N12 .320 Size 12
PM1 Cyclone Kit ComponentsThe PM1 Cyclone is used for in-stack measurement of very fine particulate matter. The 47 mm filter assembly outlet connector has a 5/8” outer diameter for easy installation Method 5 Probe Assemblies. The cyclone kit is enclosed in a sturdy plastic case.
Product description
PM1-K PM1 Cyclone Set Includes: Cyclone Body, 12 Nozzles, (PM2-NS), Filter (SFA-47), Manual and Case
PM1 PM1 Cyclone Body Only, Stainless Steel with Viton® O-Rings
PM2-NS Set of 12 Nozzles for PM1 and/or PM2.5 Cyclone, Stainless Steel
Packing List
Product description
PM2-K PM2.5 Cyclone Set Includes: Cyclone Body, 12 Nozzles, (PM2-NS), Filter (SFA-47), Manual and Case
PM2 PM2.5 Cyclone Body Only, Stainless Steel with Viton® O-Rings
PM2-NS Set of 12 Nozzles for PM2.5 Cyclone, Stainless Steel
PM2-NSA Add-On Set of 6 Nozzles (NS-7, 8, 9, 10, 11, 12) for upgrading PM2.5 Cyclone Existing Kits, Stainless Steel
O-024V Viton® O-Ring for PM2.5 Cyclone, (2 per cyclone).
O-024H High Temperature O-Ring for PM2.5 Cyclone, Stainless Steel
MPT-6-181 Pitot Tip, 3/8” Tube, Stainless Steel Replacement for Standard Method 5 Probe Assemblies
PM2.5 Cyclone Kit Components
PM2.5 Cyclone KitThe PM2.5 Cyclone is used for in-stack measurement of particulate matter equal to or less than 2.5 microns. The shank has a 5/8” outer diameter for easy adaptation to the Method 5 Probe Assemblies. The kit is enclosed in a sturdy plastic case with 12 nozzles.
Alloy 600 Components Available. Call for Pricing.
48
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
PM10 Cyclone KitPM10 is used for Method 201A testing and is designed for in-stack measurement of particulate matter equal to or less than 10 microns. The shank has a 5/8” outer diameter for easy adaptation to Method 5 Probe Assemblies. The cyclone kit is enclosed in a sturdy plastic case with twelve nozzles. Call for High Temperature Alloy 600 PM10 Cyclones and Filter Holders.
pm10-k
Product description
PM10-K PM10-K Cyclone Kit, Includes: Cyclone, 12 Nozzles Set (PM10-NS), 47mm Filter Holder (SFA-47), Manual & Case
PM10 PM10 Cyclone Only, Stainless Steel with Viton® O-Rings
PM10-NS Set of 12 Nozzles for PM10 Cyclone (Now with 12 Nozzles)
O-032V Viton® O-Ring for PM10 Cyclone
O-032H High Temperature Stainless Steel O-Ring for PM10, Cyclone
MPT-6-320 Extended Pitot Tip for PM10, SFA-300, and SFA-2590
PM10 Cyclone Kit Components
PM10/2.5 Cyclone KitPM10/PM2.5 Set combines the in-stack measurement of particulate matter (PM) equal to or less than an aerodynamic diameter of nominally 10 (PM10) and 2.5 (PM2.5 ) microns from stationary sources. The sampling train and operation are identical to Method 201A except that the PM2.5 cyclone is inserted between the PM10 cyclone and the 47mm filter. The PM10 cyclone collects particulate matter greater than PM10 while the PM2.5 collects PM less than PM10 and greater than PM2.5. The in-line filter collects PM less than PM2.5.
pm2.5-10k
Packing List
Product description
PM2.5-10K PM 2.5/10 Cyclone Kit Includes: PM10 Kit, with PM10/PM2.5 Nozzle, Cyclone Assembly, 47 mm Filter Assembly, Stainless Steel, Adapters, Pitot & Case
PM2/10-CK Connector Kit includes: GA-110 Strain Relief Adapter for PM2.5 and PM10 Cyclones, NSB-16 Button Hook Adapter for connecting the PM10/2.5 Cyclones, 10MSC5-S Connector, adapts NSB-16 to PM2.5 Cyclone, 5/8” TU to 5/16” bevel seat, Stainless Steel, and N-10UBNN SS Union, 5/8”, Bored out .660 with shoulder, Body only, No Nuts or Ferrules
PM2/10-CKI Connector Kit includes: INCONEL EQUIVALENT TO: GA-110 Strain Relief Adapter for PM2.5 and PM10 Cyclones, NSB-16 Button Hook Adapter for connecting the PM10/2.5 Cyclones, 10MSC5-S Connec-tor, adapts NSB-16 to PM2.5 Cyclone, 5/8” TU to 5/16” bevel seat, and N-10UBNN Union, 5/8”, Bored out .660 with shoulder, Body only, No Nuts or Ferrules
SFA-47 Filter Assembly, 47mm, 5/8TU, Stainless Steel, Method 17 In-Stack Filter Unit, 5/8 inch Tube Unions, uses 47mm diameter Filter Element
GA-110 Strain Relief Adapter for PM2.5 and PM10 Cyclones
NSB-16 Button Hook Adapter for Connecting the PM10/2.5 Cyclones
10MSC5-S PM10/2.5 Connector, Adapts NSB-16 to PM2.5 Cyclone,5/8” TU to 5/16” Bevel Seat, Stainless Steel
PM10/2.5 Cyclone Kit Components
PM10/2.5 Cyclone 12 Nozzle Set - 1 Each
Product Size
PM10-N6 .215 Size 6
PM10-N7 .233 Size 7
PM10-N9 .300 Size 9
Product Size
PM10-N3 .164 Size 3
PM10-N4 .180 Size 4
PM10-N5 .197 Size 5
Product Size
PM10-N10 .342 Size 10
PM10-N11 .390 Size 11
PM10-N12 .320 Size 12
Product Size
PM10-N0 .125 Size 0
PM10-N1 .136 Size 1
PM10-N2 .150 Size 2
Recommended Accessories for Sampling with Cyclone Sets.Power Box Adapter, Includes 1/2 inch Mounting Clamp and 4 Pin Amphenol to 3 Receptacles.ua-3J
Extended Pitot Tip for PM10/2.5 Sampling, Tube Diameter 3/8”, Length 421 mmmpt-6-421
47mm Glass Fiber Filters, 100/box (Whatman 934AH-4.7cm).gF-47
Sample Frame with Probe Clamp & Impinger Box SlidessB-8
49
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
CI-700K Cascade Impactor Kit includes 7 stage impactor, a PRA-K pre-cutter, nozzles, interconnecting tube, glass fiber filters (45 mm, 47 mm and GFDN filters) and foil collection plate.
Ci-700-k Stainless Steel Pre-Collector
Price description
PRA-K Pre-Cutter Assembly Kit, Includes Body, Cap, Outlet Cap with Union, Nuts, Ferrulesand Set of 6 Nozzles
PRA-N4 1/8”
PRA-N6 3/16”
PRA-N8 1/4”
PRA-N10 5/16”
PRA-N12 3/8”
PRA-N16 1/2”
PRA-NS Set of 6 Pre-Collector Nozzles, Sizes 4-16
Cascade Impactor 7 Stage 47 mm filter outlet, Viton® O-Rings, Foil collection plates.
Ci-700
Set of 7 Lightweight Stainless Steel Foil Collection Plate Inserts.
Ci-Fp
CASCAdE IMPACTOR KIT
CI-700
PRA-K
CI-700-K
data Reduction Software
Product description
PM-2.5-10C Particle Sizing Software for PM2.5 and PM10 Cyclones
PARTICLE SIZING dATA REdUCTION SOFTWARE
Functions• Calculates each stage’s aerodynamic cut point and DP50, needed to reduce particle size data. • Calculates and Stores ancillary data, such as dry gas composition and moisture content. • Reduces velocity traverse data. • Aids in selection of sample flow rates and ideal nozzle size. • Calculates flow rates and dwell times required for PM10 and PM2.5 sampling traverses. • Calculates fractional efficiencies of control devices from samples obtained at inlets and outlets.
WINCIdRS
Windows-based Cascade Impactor Data Reduction System (WINCIDRS) calculates particle size distribution of stack particulate matter (PM) taken with the Cascade Impactor, as well as particle-sizing cyclones. Developed by stack particle analysis experts, this software reduces the time and chances of error involved with reducing particle sizing data. (The PM10/2.5 Software Program (PM-2.5-10C) is extracted from WinCIDRS and simplified for use only with PM10 and PM2.5 cyclones. The calculations are similar to the WinCIDRS, scaled-down specifically for cyclone data reduction. The calculations are intensive enough to demand computer software.)
50
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
This isokinetic method is used to measure Condensable Particulate Matter (CPM) from stationary source emissions after particulate matter has been removed by a heated filter, such as in Method 5, 17 or 201A. The CPM is collected in dry impingers. The impinger contents are purged with nitrogen (N2) immediately after sample collection to remove dissolved sulfur dioxide (SO2) gases from the impinger. The organic and aqueous fractions are dried and the residues are weighed. The total of the aqueous and organic fractions represents the CPM.
METhOd 202 (dRY IMPINGER METhOd)
Schematic of the M202 Sampling Train
Method 202 Sampling Train
Components ListGNFA-3U-18K 3” filter assembly, ungrounded glass with 90 degree inlet and outlet, open style alum clamp. With rubberized silicone filter support.
GN-9AKSAKnock-out impinger assembly,ungrounded (for HorizMM5).Includes: GN-9AKSB (Bottle), GN-9AKS-I (Short Stem),GN-9AKS-IL (Purge Stem).
GF-3TM 3” PTFE membrane filter - 50 per box(Palifex 90mm).
GN-VChM-M202M202 Spiral Condenser, #28 Ball and Socket. Water Jacket Hose Barbs, High Moisture sources above 15%.
MM5-PM Mini submersible coolant pump, 110V.
MM5-PSubmersible coolant pump, 110V.
SB-4SdImpinger box - insulated coolant reservoir model 150, holds 8 impingers.
GA-28S4Stainless steel adapter, 28mm socket to 1/4” FNPT, 3” long 400°F rating.
SFA-116ILStainless steel filter housing in-line 1/4” FNPT, 3” long 400°F rating. Size: 1 Micron. Other sizes available.
SFA-1101T316L mesh stainless steel elements are recommended for filtration of heavily contaminated gases, liquids, polymers, and steam. Temperature range of -65° F to 1000°F. Withstands 1000 PSIG differential.
FILTER ANd PURGE AdAPTERFilter System for Purging Method 202.
Call for more details.
A
PurgeStem
GN-VCHM-M202
GN-8
See Page 45 for PM10-2.5 Configurations
See Page 40 for Available Pumps
See Page 28 for Full-Part Assembly Break-Down
For KnockoutGN-9AKSA
METhOd 202 (CONTINUEd ON NEXT PAGE)
GN-9AKSB (Bottle)GN-9AKS-I ( Short Stem)GN-9AKS-IL (Purge Stem)Can be Sold Separately
GN-9AKSB
GN-9AKS-IL
GN-9AKS-I
51
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
PP907-049
NTG-10UNN
Quantity Product description1 SB-4SD Two Section Divided Impinger Box
1 GN-VCHM-M202 Vertical Condenser #28 Socket to M202 Spiral Condenser, #28 Socket both ends Water Jacket Hose Barbs, High Moisture Source above 15%.
1 GN-9AKSA Glass Knock-out Impinger Assembly, Unground, (for HorizMM5) included with Long / Short Stem
1 GNFA-3U-18K CPM 3” Filter Assembly including Flexable TC
1 GF-3TM TPFE Membrane Filters with Support, 1 Micron Pore Size, 50/Box
1 MM5-P MM5-P Submersible Coolant Pump, 110V
1 MM5-PM Mini Submersible Coolant Pump, 110V
1 SB-8 Sample Frame with Probe Clamp
1 SFA-116IL Stainless Steel Filter Assembly, 3” L In-Line
2 SFA-1101T Stainless Steel FIlter Element
1 GA-28S4 #28 Socket Bored Purge Adapter
1 GN-9AKA Knock-out impinger assembly, ungrounded (for HorizMM5). Includes: GN-9AKSB (Bottle), GN-9AKS-I (Short Stem), GN-9AKS-IL (Purge Stem).
METhOd 202 SAMPLING ACCESSORIES
METhOd 202 PURGE ACCESSORIES
hEXAVALENT ChROMIUM PFA IMPINGER TRAINS & ACCESSORIES
sk-0061h sk-0061h-V
Method 0061 Hexavalent Chromium Emissions from Stationary Sources determines hexavalent chromium emissions from hazardous waste incinerators, municipal waste incinerators, municipal waste combustors and sewage sludge incinerators. Isokinetically collected with a train where the impinger reagent is recirculated continuously. Samples are analyzed with an ion chromatograph. Method 0061H Hexavalent Chromium High Temperature Source Sampling Kit is used as an alternative for temperatures above 150°C (300° F). Option “V” is added for 240 V.
Schematic of Method 0061h Sampling Train
FILTER ANd PURGE AdAPTERFilter System for Purging Method 202.
Call for more details.
hexavalent Chromium Method 0061 high or Low Temperature Source Sampling Kit
• 4’ Stainless Steel Probe Assembly (Not Heated)• Glass Probe Liners (2)• Glass Nozzle Set• PTFE Impingers
• 30’ Split Umbilical • Impinger Box• Peristalic Pump• PTFE Membrane• Sample Frame
52
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
Apex Instruments offers a wide range of filter media to meet any sampling requirements. Listed below are the standard media and sizes that Apex Instruments normally stock. Additional materials and sizes are available upon request.
FILTER MEdIA
QUARTZ FIBER FILTERSQuartz Fiber Filters are manufactured from pure quartz with-out a binder and are frequently used for sampling for metals analyses and acidic gases.
Model descriptionGF-2Q 2 inch Quartz Fiber Filters-25/box
GF-25Q 25mm Quartz Fiber Filters-100/box
GF-3Q 3 inch Quartz Fiber Filters-25/box (Pallflex 8.26cm)
GF-4Q 4 inch Quartz Fiber Filters-25/box (Pallflex 11 cm)
GF-45Q 45mm Quartz Fiber Filter-100/box
GF-47Q 47mm Quartz Fiber Filter-25/box
GF-54Q 54mm Quartz Fiber Filters-25/box (Pallflex 54mm)
GF-63Q 63.5mm Quartz Fiber Filters-25/box (Pallflex 63.5mm)
GF-3QR 3 inch Quartz Fiber Filters-100/box (MFS QR100 82mm)
GF-4QR 4 inch Quartz Fiber Filters-100/box (MFS QR100 110mm)
GF-47QR 47mm Quartz Fiber Filters-100/box (MFS QR100 47mm)
GF-90QR 90mm Quartz Fiber Filters-100/box (MFS QR100 90mm)
GLASS FIBER FILTERSGlass Fiber Filters are most commonly used filters for particulate sampling. All of the glass fiber filters are binder free and exhibit at least 99.9% efficiency for 0.3 micron dioctyl phthalate (DOP) smoke particles. Not recommended for metals analysis.
Grade E FIBER FILTERSIdeally suited for suspended solids analysis and high volume air monitoring applications. Softening point of glass fiber is 500°C, therefore upper limit temperature in use is 475°C. Low fiber shedding improves quality assurance of test results. high loading capacity. This media meets requirements for standard method 2540D and EPA Method 160.2 for establishing water quality in suspended solids content.
Model descriptionGF-2 2 inch Glass Fiber Filters-100/box
(934AH-5.5cm)
GF-2X6.5 2x6.5 inch Glass Fiber Filters-100/box (934AH)
GF-3 3 inch Glass Fiber Filters-100/box (934AH-8.26cm)
GF-4 4 inch Glass Fiber Filters-100/box (934-AH-11cm)
GF-45 45mm Glass Fiber Filters-100/box (934-AH-45mm)
GF-47 47mm Glass Fiber Filters-100/box(934AH-4.7cm)
GF-63 63.5mm Glass Fiber Filters-100/box (934-AH-63.5mm)
GF-90 90mm Glass Fiber Filters-100/Box (934AH-9.0cm)
GF-2E 2 inch Glass Fiber Filters-100/box Grade E
GF-3E 3 inch Glass Fiber Filters-100/box Grade E
GF-4E 4 inch Glass Fiber Filters-100/box Grade E
GF-25E 25mm Glass Fiber Filters-100/box Grade E
GF-47E 47mm Glass Fiber Filters-100/box Grade E
GLASS FIBER FILTERS
53
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
ALUNDUM® THIMBLES (CERAMIC)Alundum® Thimbles are used for in-stack filtration for process engineering studies when a large sample is needed for analyses. These thimbles are made from fused alumina oxide and remain very constant in weight and can be re-used an infinite number of times. There are two different porosity thimbles that can be used in the SFA-300 thimble holder. The medium porosity retain particles 5 micron and larger and the coarse retain particles 20 micron and larger.
PTFE COATED GLASS FIBER FILTERS PTFE Coated Glass Fiber Filters are constructed from borosilicate microfibers and bonded with PTFE. The filters can be folded & handled without loss of fibers. Great for especially low loading rates. Specifically recommended for Method 26 & PM10 sampling.
Product descriptionGF-2T 2 inch PTFE Coated Glass
Fiber Filters-100/box
GF-3T 3 inch PTFE Coated Glass Fiber Filters-100/box (Pallflex 82.6mm)
GF-4T 4 inch PTFE Coated Glass Fiber Filters-100/box (Pallflex 11cm)
GF-25T 25mm PTFE Coated Glass Fiber Filters-100/box (Pallflex 2.5 cm)
GF-47T 47mm PTFE Coated Glass Fiber Filters-100/box (Pallflex 4.7cm)
GF-90T 90mm PTFE Coated Glass Fiber Filters-100/box (Pallflex 90mm)
PTFE FILTER MEMBRANESPTFE Filter Membranes are produced of pure PTFE resins. They withstand the most severely corrosive conditions at temperatures as high as 500°F (260°C) and down to the cryogenic range. The membrane is hydrophobic and maintains its strength wet or dry.
Model descriptionTF1121 PTFE Membrane, 47mm,
0.45 Micron (10/pack)
TF1131 PTFE Membrane, 47mm, 1-2 Micron (10/pack)
TF1141 PTFE Membrane, 47mm, 5-6 Micron (10/pack)
PTFE FILTER MEMBRANES
Product descriptionGF-3TPG 3 inch PTFE Coated Glass Fiber Filters-50/box (MFS
PG60) 82mm-Hydrophobic, Low absorption of acid gases such as SOX or NOX.
GF-4TPG 4" PTFE Coated Glass Fiber Filters-50/box (MFS PG60) 110mm-Hydrophobic, Low absorption of acid gases such as SOX or NOX.
GF-25TPG 25mm PTFE Coated Glass Fiber Filters-100/box (MFS PG60) 25mm-Hydrophobic, Low absorption of acid gases such as SOX or NOX.
GF-47TPG 47mm PTFE Coated Glass Fiber Filters-100/box (MFS PG60) 47mm-Hydrophobic, Low absorption of acid gases such as SOX or NOX.
Model descriptionGF-300C Alundum Thimble, medium porosity, 5+ micron retention, 34x100ml,
round bottom, fits SFA-300 use with additional O-ring, O-123V.
GF-300C-C Alundum Thimble, COARSE porosity, 20 micron retention, 34x100ml, round bottom, fits SFA-300 use with additional O-ring, O-123V.
GF-300C
IN-STACK THIMBLES AND ACCESSORIES Apex Instruments stocks a variety of Fiber Thimbles for in-stack particulate sampling. The thimbles are seam-less, high purity filters and available from a choice of two different types of fibers: Borosilicate glass and quartz. Borosilicate glass fiber thimbles are acid washed to reduce the trace metal content to an absolute minimum. Quartz fiber thimbles are strengthened with alumina and are prefired at 900°C for 2 hours during manufacturing to stabilize the weight prior to use. The gas collection efficiency of the thimbles is 99.9% (0.3 micron DOP). The 25 x 90mm thimbles are specifically manufactured for stack sampling and tapered for ease in loading. Cellulose thimbles are available upon request.
GF-2590Q
Model descriptionTF1165 PTFE Membrane, 25mm, 30-60 Micron (10/Pack)
GF-3TM 3 inch PTFE Membrane Filters-50/box (82.6mm) PTFE filter media provides durability for hostile acid aerosol monitoring. 1.0µm pore size membrane.
PTFE FILTER MEMBRANES
Model descriptionGF-190Q 19X90mm Quartz Fiber Filter
Thimble-25/box (For SFA-190)
GF-300Q 30x100mm Quartz Fiber Filter Thimble-25/box (For SFA-300) grade 88R
GF-2590Q 25x90mm Tapered Quartz Fiber Thimble-10/box (For SFA-2590) Grade 88R
QUARTZ FIBER THIMBLESModel descriptionGF-190 19x90mm Glass Fiber Filter
Thimble-25/box (For SFA-190)
GF-2590 25x90mm Tapered Glass Fiber Thimble -10/box (For SFA-2590) Grade 86R
GF-300 30x100mm Glass Fiber Filter Thimble-25/box (For SFA-300) Grade 86R
GLASS FIBER FILTER THIMBLES
ACETATE FILTERGF-47MMAT - FILTER, ACETATE, 47MM,.45 PORE, 100/PK. This filter is used in the SK-0061H system for sampling Hexavalent Chromium.
54
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
PTFE Probe Brush Extensions The flexible PTFE Probe Brush Extension attaches to the PBT-5/8 or PB-5/8. Made with 8/32 threads with a phenolic knob. Please specify length.
PTFE Probe BrushAll PTFE construction. The PBT-5/8” diameter with four spiral rows of black PTFE bristles. Over all length is 2”. The shaft is 1/4” diameter with 8-32 female threads. PTFE Barrel and PTFE Bristles.PBT-5/8
SAMPLE RECOVERY
PBT-5/8
NB-SET
B-3
B-4
PBX-S
Modular Probe Brush Set The PBX-S Modular Probe Brush Set contains two of the 5/8” stainless steel twisted wire brushes with nylon bristles and a total of 13’ in stainless steel extensions.PBX-S....$105.00
Model description
PB- 5/8 Probe Brush/Stainless Steel, Nylon Bristles
PBX-2 2’ Probe Brush Extension, Stainless Steel
PBX-3 3’ Probe Brush Extension, Stainless Steel
PBK-832 Probe Brush Knob
NOZZLE BRUSh SET The NB-SET Nozzle Brush Set includes one each of the three most popular sizes in a convenient carrying tube. (#3,#5,#8)NB-SET
B-1
Impinger Bottle Brush with Plastic Handle and Nylon Bristles.B-1
Impinger Bottle Brush
B-2
Flask Brush, Stainless Steel Handle and Nylon Bristles.B-2
Flask Brush
Filter Brush, 3/16” diameter, Stainless Steel Handle and Nylon Bristles, 5/16”.B-3
Filter Recovery Brush
Rubber Policeman with 18” Delrin® HandleB-4
Policeman
Model description
PBX-4T 4” PTFE ProbeBrush Extension
PBX-6T 6” PTFE Probe Brush Extension
PBX-8T 8” PTFE Probe Brush Extension
PBX-10T 10” PTFE Probe Brush Extension
PBX-12T 12” PTFE Probe Brush Extension
Brush Sold Separately
PTFE NOZZLE BRUShES Nozzle Brush NBT-1/2 is constructed of pure PTFE featuring a 1/8” diameter shaft with 1/2” long soft PTFE bristles. NBT-1/2
NBT-1/2
PBX- T
NOZZLE BRUShES Apex Instruments Nozzle Brushes feature stainless steel handle and nylon bristles. Super flexible for cleaning button hook nozzles with eye tip to reduce scarring of the nozzle.
Model description
NB-3 3/16” diameter, Nylon Bristles
NB-5 5/16” diameter, Nylon Bristles
NB-8 1/2” diameter, Nylon Bristles
NB-5
NB-8NB-3
55
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
250ML-CyL-PMP
Aluminum Weighing dishes (70 ml)100/pack.25433-062
Aluminum Weighing dishes 100 Pack (12.1 cm) 12175-001
Petri dish 100x15mm PL 25/pack (for 3-inch filters), Polystyrene.25373-1100
Petri dish 150x15mm PL 10/pack (for 4-inch filters), Polystyrene.25373-187
Graduated Cylinder 250ml, Plastic250ML-CYL-PMP
Graduated Cylinder 250ml, Glass250ML-CYL
TW-1
Nylon TweezersTW-1
Polypropylene FunnelTop Diameter 108mm.
30255
Funnel Parafilm M, Laboratory Sealing Film, Roll is 2” x 250 ft.PARA-2X250
Synthetic Cotton Balls (For Impinger Outlet Filter), 300/bagMS-1
Cotton Balls
SAMPLE RECOVERY BOTTLES
FEP WASh BOTTLE500mL Wash Bottles, FEP.WB-500Fep
WB-500FEP
GSB-250
GLASS BOTTLES250mL Glass Sample Bottles with PFA-Lined Lid.Case of 12.gsB-250
SAMPLE RECOVERY ACCESSORIES
WB-5P
PLASTIC WASh BOTTLE500mL Plastic Wash BottlesWB-5p
POLYEThYLENE SAMPLE BOTTLES
Wide Mouth Bottles for Easy Filling and Pouring. The HDPE bottle with polypropylene closures are made of FDA compliant material. Recycling code molded into base of bottles. Simple to pour-wide mouth bottles. Chemically resistant. Leak proof, firm. Excellent for packaging chemicals, pharmaceuticals and adhesives.
WB-1W - 125 mL vw/Wide Mouth, w/Cap.
WB-2p - 250 mL w/Cap.
WB-2pW - 250 mL w/Wide Mouth.
WB-4p - 16oz./500 mL w/Wide Mouth.
WB-10p - 1000 mL w/Wide Mouth.
WB-1000pW - 1000 mL w/Wide Mouth.
56
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
dESICCATOR ANd dESICCANTS Acrylic Desiccator Cabinets feature adjustable shelves with grooves for positioning, removeable lip tray, gasketed door, built-in hygrometer. Cabinets do not include Desiccant, order separately.
31000
www.belart.com
Features• Patented Sealed Construction is Airtight, Dust and Moisture Free.• Portable and Stackable with a Small Footprint.
PORTABLE dESI-VAC CONTAINER Desiccator with a vacuum pump is ideal for drying, preserving, storing, and even shipping samples. Vacuum pump built into the top removes air with manual strokes. Rubber O-ring sealed cover maintains vacuum. Achieves a vacuum of better than 200 inches of water (15 inches of mercury). A release button on top allows air into the container to remove the lid. Sample Humidity Sponges™ desiccant drying packets are included. O-ring-sealed cover maintains vacuum. Achieves a vacuum of better than 200 inches of water (15 inches of mercury A release button on top allows air into the container to remove the lid. Keep powder dry. Plastic container is ideal for storing chemicals, powders, tissues, plant sections, electronics, and weighing samples. Vacuum and desiccants keep mate-rial dry. Supplied with a vacuum indicating button that confirms interior vacuum and a dial hygrometer that displays 0 to 100% relative humidity with a resolution of 2%RH.Dimensions: HxWxD: 11” x 9” x 10”.
des-3164dES-3164
• Embedded UV Protection and Superior Chemical Resistance.• Built-in Hygrometer for Quick Check on RH Levels.• Rugged Construction with Sturdy Latches and Lock Provisions.
Model description dimensions Features
DES-10000 Desiccator Cabinet 8.4” x 13.4” x 16.3” Gasketed door, built in hygrometer, 0.75 cu.ft.
DES-21000 Desiccator Cabinet 12.4” x 13.4” x 16.3”, Gasketed door, 2 shelves, built in hygrometer 1.17 cu.ft.
DES-21115 Auto-Desiccator Cabinet
12.4” x 13.4” x 16.3” Gasketed door, 2 shelves, built in hygrometer 1.17 cu.ft. 110V
DES-21115V Auto-Desiccator Cabinet
12.4” x 13.4” x 16.3”, Gasketed door, 2 shelves, built in hygrometer 220V fan, 1.17 cu.ft.
DES-31000 Desiccator Cabinet 16.4” x 13.4” x 16.3”, Gasketed door, 3 shelves, built in hygrometer stackable
DES-31115 Auto-Desiccator Cabinet
16.4” x 13.4” x 16.3”, Gasketed door, 3 shelves, built in hygrometer stackable, 110V
DES-31115V Auto-Desiccator Cabinet
16.4” x 13.4” x 16.3”, Gasketed door, 3 shelves, built in hygrometer 220V fan
DES-40000 Desiccator Cabinet 13.4” x 20.4” x 16.3”, Gasketed door, 2 shelves, horizontal Profile
DES-41115 Auto-Desiccator Cabinet
20.4” x 13.4” x 16.3” Gasketed door, 3 shelves, built in hygrometer
DES-41220 Auto-Desiccator Cabinet
20.4” x 13.4” x 16.3”, Gasketed door, 3 shelves, built in hygrometer, 220V fan
57
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
SILICA GELBlue Indicating, 3-5mm Bead, 12/case, 250 ml per bottle.
sg-kitSG-KIT
Apex Instruments Silica Gel is primarily used for drying sample gas prior to measurement and can absorb moisture 40% of its weight. The silica gel can be regenerated by drying in an oven and used over and over again.
SILICA GEL
SILICA GEL3-5mm Bead, Indicating, 2.3Kg.
sg-3/5B
24005 14005
Part Number description
13005 DRIERITE®, Nonindicating 8 Mesh, 5 Lbs. (2.3 kg)
14005 DRIERITE®, Nonindicating 10-20 Mesh, 5 Lbs. (2.3 kg)
23005 DRIERITE®, Indicating 8 Mesh, 5 Lbs. (2.3 kg)
24005 DRIERITE®, Indicating 10-20 Mesh, 5 Lbs. (2.3 kg)
SG-3/5B
The activated alumina is primarily used for air drying at low temperature applications, 5.5 lb. Container.
80% Activated Alumina (White). 1/8” Diameter Beads.
20% Silica Gel (Blue) 3-5 mm Beads.
Aluma-Sorb
ACTIVATEd ALUMINA WITh SILICA GEL
Aluma-sorb
SILICA GEL3-5 mm Bead, Bulk55 LBS, CONTAINER.
sg-3/5B-55
Ah-610-A
dRIERITE® dESICCANTSApex Instruments carries both non indicating and indicating DRIERITE®. (anhydrous calcium sulfate) Economical to use, it can be regenerated repeatedly. The indicating DRIERITE® is impregnated with cobalt chloride: blue when dry and changes to pink upon absorption of moisture.
SG-3/5B-55
With Aluma-Sorb AH-610-A
ah-610-Ca-6tu
ah-610-CaCr-4tu
SG-616-25LB
SILICA GELSG-616 - IndicatingSG-616N - Non Indicating
58
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
BALANCES
MOdEL dESCRIPTION
BAL-EJ1500 1500g x 0.1 g.
BAL-EJ3000 3100g x 0.1 g.
BAL-EJ6100 6100g x 0.1 g.
BAL-EJ02 USB Interface with Cable
BAL-EJ12 Carrying Case
EJ-SERIES• Easy to read LCD Display with Backlight
• Percentage and Counting
• USB or RS-232 Interface Optional
• Battery Operated (4 x AA not included)
• AC Adapter Included
• Pan Size: 5” x 5.5”
• Check-Weighing Capacity
• 5 Year Warranty
PORTABLE BALANCES
MOdEL dESCRIPTION WEIGhT
BAL-W1000ASTM Weight for Electronic Balance. 1 kg. ASTM GRADE 7
BAL-W2000ASTM Weight for Electronic Balance. 2 kg. ASTM SHAPE
BAL-W5000ASTM Weight for Electronic Balance. 5 kg. Class F, meet Tolerances of NIST
CALIBRATION WEIGhTS
COMES wiTh CERTiFiCATE OF CONFORMANCE
59
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
BALANCES
MOdEL dESCRIPTION PAN SIZE
BAL-HR60-C 60g x 0.1mg with RS-232C. 3.3”
BAL-HR120-C 120g x 0.1mg with RS-232C. 3.3”
BAL-HR200-C 210g x 0.1mg with RS-232C. 3.3”
BAL-HR202i 220g/51g x 0.1mg/0.01mg Semi-Micro with R-232C. 3.6”
hR-SERIES• Percentage and Counting Modes.
• Digital Preset Tare.
• One Touch Printing.
• Last Digital Suppression.
• Standard Underhook.
• Optional Rechargeable Battery Pack.
• GLP/LIMS/ISO Compliant.
• RS-232C Standard.
• 5 Year Warranty.
ANALYTICAL BALANCES
Analytical Balances - Calibration Weight Set
MOdEL
BAL-W1-100
dESCRIPTIONWeight Set - 1mg-100gStainless Steel Calibration Weight Set for Lab Use. Set of 9 Weights Plus Fractional Weights in Wooden Storage Box.
Note: Please check with State Department of Weights and Measurements for calibrations.
60
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
dGM-110SR
METER CALIBRATIONCALIBRATION SERVICESApex performs both calibrations using a wet test meter and bell-prover primary standard. Calibration services are available from Apex Instruments on a fee per console basis. Extra charge for low flow. All console and dry gas meter calibrations are conducted in accordance with U.S. EPA standards. Apex Instruments calibrates source sampler consoles, reference dry gas meters, orifices and pitots.
Calibration being performed with Wet Test Meter
dRY GAS SECONdARY REFERENCE METER (ENGLISh) Dry Gas Meter Secondary Reference Meter (Standard) with 15 pt cal, valve, 5’ hose, 1/2” Quick Connect. Used for calibrating Method 5 Source Sampler Consoles. dgm-110sr
dRY GAS METER KG3S W/ REPLACEMENT KIT FOR SK25 dGM IN XC-572 Replacement Kit for KG3S to replace SK25 DGM in an existing model XC-572 meter console. Includes KG3S DGM with nuts and o-rings, adapter plate, support bracket, bushings, standoffs and screws.
dgm-kg3skkit
METER CALIBRATION EQUIPMENT
Model description
DGR-CAL15-LF Calibration of DGM for Secondary Reference, 15 Point, Low Flow 900, 750, 600, 450, 300 ccm (3 runs at each flow rate).
DGR-CU-ST Calibration of DGM for Secondary Reference, 15 Point 1.2, 1.0, 0.5, .035 cfm (35, 30, 21, 15, 11 lpm).
DGR-2VER Verification of DGM for Secondary Reference, 2 Point Verification of Previous Calibration.
DGMC-5A Pre-Test 5 Point Calibration for Compatible Meter Consoles.
DGMC-5A-LF Pre-Test 5 Point Low-Flow (less than 1Lpm) Calibration for Apex Meter Consoles Service only - 900, 750, 600, 450, 300 ccm.
DGMC-5AD-LF Pre-Test 5 Point Low-Flow (less than 1Lpm) Calibration for Apex Meter Consoles (Dual)Service only - 900, 750, 600, 450, 300 ccm.
DGMC-3A Post Test 3 Point Calibration for Meter Consoles.
DGMC-3A-LF Pre-Test 3 Point Low-Flow (less than 1Lpm) Calibration for Apex Meter Console. 900, 600, 300 ccm.
DGMC-3AD-LF Flow Post-test 3 Point Low-Flow (less than 1Lpm) Calibration for Apex Dual Meter Consoles. 300, 400 & 500ccm. 900, 600, 300 ccm.
CAL-ORF Orifice Calibration, 3 Point (priced per orifice assembly).
dRY GAS METER CALIBRATION SERVICES
dGM-KG3SKKITdRY GAS METER KG3S W/ REPLACEMENT KIT FOR AP25 dGM IN XC-572 Replacement Kit for KG3S to replace AP25 DGM in existing model XC-572 meter console. Includes KG3S DGM with nuts and o-rings, adapter plate, bushings, standoffs and screws.
dgm-kg3apkit
The configuration for the replacing the AP25 does not require the support bracket.
dgm-kg2srddgm-kg3srdgm-kg3-srd5k
61
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
U.S. EPA allows critical orifices to be used as calibration standards. The orifice calibration set contains five of our critical orifices with 1/2” quick connects and software. Recalibration recommended annually. Calibration Orifice Set, 5 Calibrated Critical Orifices and Spreadsheet Diskette for Method 5.
CALIBRATION ORIFICE SET
m5Co-set
Available on CD
Model A description: Shinagawa Precision Wet Test Meter Weight height Width depth
W-NK-0.5A Max Flow 5 LPM, 0.5 Liter per Revolution 4.5kg 420 290 190
W-NK-1A Max Flow 10 LPM, 1 Liter per Revolution. 6.0kg 450 315 210
W-NK-2A Max Flow 20 LPM, 2 Liter per Revolution 9.0kg 390 350 255
W-NK-2.5A Precision Meter, 2.5 Liter Capacity, 5 to 1500 L/HR 9.0kg 390 350 255
W-NK-5A Precision Meter, 5 Liter Capacity, 5 to 3000 L/HR 25kg 575 455 295
W-NK-10A Precision Meter, 10 Liter Capacity, 20 to 6000 L/HR 35kg 656 535 380
The Best Standard for Calibration of dry Gas Meters.
Different Models Available.
The Model W-NK Wet Gas Meter is a net-volume type integrating flowmeter that employs a drum as the metering element. As the drum is sealed with water or other fluid, the Model W-NK provides the measurement of any gas irrespective of the gas specific gravity and viscosity. Further, since this gas meter permits the measurement of very small flows, exhibits high reproducibility, and offers various other excellent features, it properly serves as a standard as well as a testing instrument.
PRECISION WET TEST METERSCALIBRATION EQUIPMENT ANd SERVICES
Model B description: Shinagawa Precision Wet Test Meter Weight height Width depth
W-NK-0.5B Max Flow 5 LPM, 0.5 Liter per Revolution, Corrosion Resistant 4.5kg 420 290 190
W-NK-1B Max Flow 10 LPM, 1 Liter per Revolution, Corrosion Resistant 6.0kg 450 315 210
W-NK-2B Max Flow 20 LPM, 2 Liter per Revolution, Corrosion Resistant 9.0kg 390 350 255
W-NK-2.5B Precision Meter, 2.5 Liter Capacity, 5 to 3000 L/HR, Corrosion Resistant
9.0kg 390 350 255
W-NK-5B Precision Meter, 5 Liter Capacity, 5 to 3000 L/HR, Corrosion Resistant
25kg 575 455 295
W-NK-10B Precision Meter, 10 Liter Capacity, 20 to 6000 L/HR, Corrosion Resistant
35kg 656 535 380
W-NK
Model description
M5CO-40 Calibration Critical Orifice, Size 40, Flow Rate. ~.31cfm (~8.8 lpm) with 1/2” Male QC
M5CO-48 Calibration Critical Orifice, Size 48, Flow Rate. ~.46cfm (~13.0 lpm) with 1/2” QC
M5CO-55 Calibration Critical Orifice, Size 55, Flow Rate. ~.61cfm (~17.3 lpm) with 1/2” QC.
M5CO-63 Calibration Critical Orifice, Size 63, Flow Rate. ~.79cfm (~22.4 lpm) with 1/2” QC.
M5CO-73 Calibration Critical Orifice, Size 73, Flow Rate. ~1.1cfm (~31.14 lpm) with 1/2” QC.
Orifice Set Contains the following:
62
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
dIAL CALIPERS
Geometric of Type-S Pitot Tube to Method 2.
pt-Cal-gWind Tunnel of Type-S Pitot Tube to Method 2.
pt-Cal-W
PITOT CALIBRATION SERVICES
ThERMOCOUPLE SIMULATOR / CALIBRATOR This Thermocouple Simulator/Calibrator has precise temperature inputs to all types of instruments, transmitters, recorders, controllers, alarms, data acquisition and computer systems. Provides 18” extension wire output and is cold junction compensated for changes in ambient temperature. Ac-curate source for checkout and calibration of all thermocouple instruments. Practical Instrument Electronics (PIE) Model 520 Thermocouple Simulator simulates a dedicated standard thermocou-ple curve over the entire industrial temperature range.
m5C-520
dial Calipers are used for measuring nozzle diameter and inspection of pitots. Dial Caliper, 0-6”/ 150mm Direct inch/Metric Conversion.
m5C-3d
NOZZLE CALIBRATION
CALIBRATION EQUIPMENT ANd SERVICES
M5C-520
BULL’S EYE LEVELBull’s Eye Level is 1/2” diameter and used for pitot calibrations. Comes with thumb screws for clamping to pitot.
m5C-2
M5C-2
Pendulum Style Inclinometer for the Calibration of Type-S Pitots.
inC-a300
A300 LEVEL INdICATOR
INC-A300
PITOT AUdIT EQUIPMENT & MANOMETERS
Meriam Handheld, LCD DISPDigital Manometer, Hand held, 0-28 inch H2O Selectable Range, English/Metric, with certificate of NIST traceability.
dhm-m100
hANdhELd MANOMETER
dhM-M100
hANdhELd MANOMETER LCD DISP., Digital Manometer, Method 2, Hand held, 0-10 inch H2O Selectable Range, English/Metric.
dhm-28-10
dhM-28-10
MANOMETER SOFTWARE Software and cable for Digital Manometer, HM28 series.
dhm-28-1
MANOMETER dIGITAL dISPLAYDP-CALC Micromanometer makes differential pressure measurements, static, total, and velocity pressures as well as pressure drops across filters, coils, fans, and diffusers. Differential and static pressure from -15 to +15 in. H2O (-3735 to +3735 Pa) lightweight and durable design with an easy-to-read display, certificate of NIST traceability.
dhm-5825
63
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
MONORAILS
MONORAIL hARdwARe
(Threaded pipe flanges are available in 3”, 4” or 6”, stainless steel or aluminum.) Note: The chain must be attached to the stack so that the chain angle to the monorail is no less than 30° (45° is recommended).
PF- CSPipe Flange
PART # Monorail with Cable and Chain LF
P1001-10 MONORAIL, 10FT, STEEL Heavy Duty, Double Channel, W/CHAIN, L-Bracket & Hardware.
10
P1001-12 MONORAIL, 12FT, STEEL Heavy Duty, Double Channel, W/CHAIN, L-Bracket & Hardware.
12
P1001-14 MONORAIL, 14FT, STEEL Heavy Duty, Double Channel, w/ Adjustment Chain, L-Bracket & Hardware.
14
P1001-16 MONORAIL, 16FT, STEEL Heavy Duty, Double Channel, w/Cable, Adjustable Strap, L-Bracket & Hardware.
16
P1001-17 MONORAIL, 17FT, STEEL Heavy Duty, Double Channel, w/Cable, Adjustable Strap, L-Bracket & Hardware.
17
P1001-18 MONORAIL, 18FT, STEEL W/CHAIN Heavy Duty, DoubleChannel, w/Cable, Adjustable Strap, L-Bracket & Hardware.
18
PART # Flange
PF-3CS Flange, 3” 150 lb. FF, 2.67 Bored, Stainless Steel, with Threaded Coupling.
PF-4CS Flange, 4” 150 lb. FF, 2.67 Threaded, Stainless Steel, with Threaded Coupling.
PF-6CLS Flange, 6” 150 lb. FF, 2.67 Bored, Stainless Steel with Cam-lock Connector.
See Accessories Section for Different Configurations.
PART # Trolley and Monorail Support Bracket
P2751 MONORAIL, TROLLEY Swivel Frame Trolley with Eyebolt, 1 Foot Chain and Snap-hook.
P501 MONOMOUNT, MONORAIL SUPPORT Support Bracket; Fits 3”, 4”, 6” & 8”, Standard Pipe Flanges, Includes P1354 Hinge, (4) P3010 Nuts and P371 Bolts.
Link to Flanges
LF 6 7 8 9 10 12
Part # P1000-6 P1000-7 P1000-8 P1000-9 P1000-10 P1000-12
Probe Size
For use with probes over 6’
For use with probes over 7’
For use with probes over 8’
For use with probes over 9’
For use with probes over 10’
For use with probes over 12’
Monorail with ChainHeavy Duty Steel Monorail with Chain, L-Bracket and Hardware (for use with probes).
64
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
XC-522 and XC-572 Components ListPart Number Description QC-MAN-M2 QC-Manometer, M-1/4HB, Delrin XC-10U Black RotoRack Shallow Case M-RA911 Switch, Curvette, EC Comp., I-O AM-MCP Replacement Meter Console Wired Amphenol Sub-Assembly M-422B Bracket, Manometer, Adjust, Stainless Steel M-422DS Manometer Displacer Knob L-441160 Latch, Panel, Screw, Large, Sou 3439T12 Webbing, 2”, Black Nylon M-CBR5A-M Magnetic Type Circuit Breaker Rocker Switch, 5 Amp., 120V M-CBR3A-M Magnetic Type Circuit Breaker Rocker Switch, 3 Amp., 240V
Part Number Description TC-765KF Display, TC, PNI, LED, 120/220V M-SD31 Controller, Temp, Red LED, Watlow MC-T Timer, MC, Veeder-Root M-SCKT15A Conn, Pwr, IEC Inlet 15A/250V M-49BK Recept, EL, Snap-In, Term M-31302A Switch, TC. 7 Channel TC-PJK TC Jack, Type K, PNL, Snap-In QC-BHF8-SS QC, Blkhd, 1/2IN-1/2TU, F, SS QC-BHF4-SS QC, Blkhd, 1/4IN-1/4TU, F, SS QC-BHF6-SS QC, Blkhd, 3/8IN-3/8TU, F, SS QC-BHM6-SS QC, Blkhd, 3/8IN-3/8TU, M, SS B2VH-6S Valve, Ball, 3/8TU, SS, PNL, Nut NV3HA-6S Valve, Needle, Angle, 3/8T-3/8T, S DGM-110 Meter, Dry Gas, 110 Rockwell G301U Gage, Vac, 0-30HG, 1.5IN, PNL M-42210 Manometer, Dual, PNL, 0-10” H2 QC-MAN-F3 QC-Manometer, F-1/8MNPT, S
1234567891011121314151617
18192021
22
23242526
27
xc-522 Source Sampling conSole (engliSh) xc-572 Source Sampling conSole (metric)
TC-765KF
Temperature Display
Manometer Quick Connects
Fine Control Valve
Manometer Zero Adjust Knobs
Manometer Level Adjust
Standard Stainless Steel Pitot Quick
Connects
Standard Stainless Steel Sample Quick Connect
Standard StainlessSteel Female Pump Connection (Pressure)
UmbilicalCable Power Connection
Color Coded Thermocouple Jacks
7-ChannelTemperature
Selector Switch
Vacuum Gauge
Elapsed Timer
Rugged Custom Molded X-Case
Digital Filter and Probe Temperature
Controllers
Stainless Steel MaleNon-Reversible Pump
Quick Connect(Vaccum)
Strap
9
10
11
1
7
XC-10U19
13
4
21
ElectricReceptacle
Power Connect Inlet
25 3439T12
Heavy Duty Panel Latches
24 L-441160
XC-522 Dry English Gas Meter14 DGM-110
CoarseControl Valve
12 B2VH-6S
Dual Column
Manometer
16 M-42210
1718 QC-MAN-M2
QC-MAN-F32 M-SD31
MC-T
G301U
3
15
M-31302A 6
TC-PJK
QC-BHM6-SS
QC-BHF6-SS
5M-49BK
QC-BHF8-SS8
QC-BHF4-SSAM-MCP NV3HA-6S
M-422B22
M-422DS23
Rocker Switches
M-RA91120
M-SCKT15A
xc-522
28 DGM-AP25
XC-572 Dry Metric Gas Meter
XC-572 (Metric) DGM-AP25 Meter, Dry Gas, AP25 W/Union 28
Magnetic Type Circuit Breaker Rocker Switch
M-CBR3A-M27
M-CBR5A-M26
Call for information on 110V / 240V Models.
65
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
ConVersion FaCtorsConversion Factors
To Convert From to Multiply ByareaSquare Feet (ft2) Square Centimeters (cm2) 929.0304
Square Feet (ft2) Square Meter (m2) 0.09290304
Square Feet (ft2) Square Inches (in2) 144
Square Inches (in2) Square Centimeters (cm2) 6.4516
LengthFeet (ft....) Centimeters (cm) 30.48
Feet (ft....) Meters (m) 0.3048
Feet (ft....) Inches (in) 12
Inches (in) Millimeters (mm) 25.4
Inches (in) Centimeters (cm) 2.54
Mass/ForcePounds (lb) Grains (gr) 7000
Pounds (lb) Grams (g) 453.59237
Grains (gr) Grams (g) 0.06479891
Kilograms (kg) Pounds (lb) 2.2046226
Kilogram-force (kgf) Newton (N) 9.80665
Pound-Force9 (lbf) Newton (N) 4.44822
TemperatureDegrees Celsius (°C) Kelvin (K) K = °C + 273.15
Degrees Celsius (°C) Degrees Fahrenheit (°F) °F = 9/5 (°C + 32)
Degrees Fahrenheit (°F) Degrees Rankine (°R) °R = °F + 459.67 = 1.8k
Degrees Fahrenheit (°F) Degrees Celsius (°C) °C = 5/9 (°F -32)
Power, Energy, HeatBritish Thermal Unit per Min. (Btu/min.) Steam, Pounds per Hour (lb/hr Steam) 1 X 103
Horsepower (hp) Watts (W) 745.7
Horsepower, boiler (hp) British Thermal Unit Per Hour (Btu/hr) 33445.7
Horsepower, boiler (hp) Kilowatts (kW) 9.8095
Kilowatts, Hours (kWhr) British Thermal Unit Per Hour (Btu/hr) 3414.43
British Thermal Unit, mean (Btu) Kilogram-Calories (kcal) 0.252
British Thermal Unit, mean (Btu) Watts per Second, Joule (J) 1055.06
PressureInches of Mercury (in Hg) Millimeters of Mercury (mm Hg) 25.4
Inches of Mercury (in Hg) Inches of Water (in H20) 13.6
Inches of Mercury (in Hg) Atmospheres (atm) 0.0334211
Inches of Mercury (in Hg) Kilopascals (kPa) 3.386388
Atmospheres (atm) Bars (bar) 1.01325
Atmospheres (atm) Pounds per Square Inch (psi) 14.695949
Pascals (Pa) Newton per Square Meter (N/m2) 1.0
VolumeCubic Meters (m3) Cubic Feet (ft3) 35.314667
Cubic Feet (ft3) Liters (l) 28.136847
Liters (l) Cubic Centimeters (ccm) 1000
66
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
equations
67
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
Avogadro’s Number 6.02 x 1023 atoms/g atomGas Constants 82.05 atm cm3/(g-mole * K) 1.987 cal/(g-mole * K) 10.731 ft.... lb in2/(lb-mole * oR) 0.732 ft3 atm/(lb-mole * oR)1 g-mole of Ideal Gas 24.05 Liters at US EPA Standard Conditions
Constants
Standard Temperature (Tstd) 20oC (68oF)Standard Pressure (Pstd) 760mm Hg (29.92in Hg)
us epa standard Conditions
gas ConCentration unitsParts-per-million by volume (ppmv) to milligrams per dry standard cubic meter (mg/dscm)
Correct to x% O2
−−
×=)(2
2%@ %9.20
%9.202
dryactualsOxs O
OxCC
Gas Concentration UnitTo Convert From To Multiply ByParts-per-million(ppm) SO2 Nanogram/Std Cubic Meter (ng/scm) SO2 2.66 x 106
Parts-per-million(ppm) SO2 Pounds/Std Cubic Foot (lb/scf) SO2 1.660 x 10-7
Parts-per-million(ppm) NOx Nanogram/Std Cubic Meter (ng/scm) NOx 1.912 x 106
Parts-per-million(ppm) NOx Pounds/Std Cubic Foot (lb/scf) NOx 1.194 x 10-7
68
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
An Sampling Nozzle Cross-Sectional Area, mm2 (in2)As Stack Cross-Sectional Area, m2 (ft2)Bws Percent Moisture in Stack Gas, % H2OCp Pitot Tube Calibration CoefficientCp(std) Standard Pitot Tube Calibration Coefficientcs Particulate Concentration in Stack Gas, g/dscm gr/dscm (lb/dscf gr/dscf)De Equivalent Diameter, m (ft....)Dn Sampling Nozzle Diameter, mm (in)∆p Stack Gas Velocity Pressure, mm H2O (in H2O)(∆p1/2) avg Average of the Squareroots of Velocity Pressure, (mm H2O)1/2 (in H2O)1/2
%EA Percent Excess Air, %Fd F factor for dry effluent, used with percent O2, dry basisFo Fuel Factor∆H@ Pressure Drop across Orifice Meter for 21.2 lpm (0.75cfm) at Std Conditions, mm H20 (in H2O)∆H Pressure Drop across Orifice Meter, mm H20 (in H2O)%I Isokinetic Sampling Rate, %K Isokinetic Rate ConstantK’ Critical Orifice Calibration FactorKp Pitot Tube ConstantL Length of Duct Cross-Section at Sampling Site, m (ft....)m Mass, g (lb)Md Stack Gas Dry Molecular Weight, g/g-mole (lb/lb-mole)Ms Stack Gas Wet Molecular Weight, g/g-mole (lb/lb-mole)pmr Pollutant Mass Emission Rate, kg/hr (lb/hr)Pb Barometric Pressure, mm Hg (in Hg)Ps Absolute Stack Pressure, mm Hg (in Hg)Pstd Standard Pressure, 760 mm Hg (29.92 in Hg)Qaw Actual Wet Volumetric Flowrate, acmm (acfm)Qsd Dry Standard Volumetric Flowrate, dscmm (dscfm)ρw Density of Water, 0.9982 g/mlθ Time (minutes)Ts Stack Temperature, oC (oF)Tstd Standard Temperature, 293K (528oR)Tamb Ambient Temperature, oC (oF)Vcr Critical Orifice Volume, m3 (ft3)Vm Dry Gas Meter Volume, m3 (ft3)Vlc Volume or Mass Liquid Collected in Impingers, ml or gW Width of Duct Cross-Section at Sampling Site, m (ft....)y Dry Gas Meter Calibration Factor
nomenClature
69
ISOKINETIC SOURCE SAMPLING EQUIPMENT
www.apexinst.com 800-882-3214 / 919-557-7300
An Sampling Nozzle Cross-Sectional Area, mm2 (in2)As Stack Cross-Sectional Area, m2 (ft2)Bws Percent Moisture in Stack Gas, % H2OCp Pitot Tube Calibration CoefficientCp(std) Standard Pitot Tube Calibration Coefficientcs Particulate Concentration in Stack Gas, g/dscm gr/dscm (lb/dscf gr/dscf)De Equivalent Diameter, m (ft....)Dn Sampling Nozzle Diameter, mm (in)∆p Stack Gas Velocity Pressure, mm H2O (in H2O)(∆p1/2) avg Average of the Squareroots of Velocity Pressure, (mm H2O)1/2 (in H2O)1/2
%EA Percent Excess Air, %Fd F factor for dry effluent, used with percent O2, dry basisFo Fuel Factor∆H@ Pressure Drop across Orifice Meter for 21.2 lpm (0.75cfm) at Std Conditions, mm H20 (in H2O)∆H Pressure Drop across Orifice Meter, mm H20 (in H2O)%I Isokinetic Sampling Rate, %K Isokinetic Rate ConstantK’ Critical Orifice Calibration FactorKp Pitot Tube ConstantL Length of Duct Cross-Section at Sampling Site, m (ft....)m Mass, g (lb)Md Stack Gas Dry Molecular Weight, g/g-mole (lb/lb-mole)Ms Stack Gas Wet Molecular Weight, g/g-mole (lb/lb-mole)pmr Pollutant Mass Emission Rate, kg/hr (lb/hr)Pb Barometric Pressure, mm Hg (in Hg)Ps Absolute Stack Pressure, mm Hg (in Hg)Pstd Standard Pressure, 760 mm Hg (29.92 in Hg)Qaw Actual Wet Volumetric Flowrate, acmm (acfm)Qsd Dry Standard Volumetric Flowrate, dscmm (dscfm)ρw Density of Water, 0.9982 g/mlθ Time (minutes)Ts Stack Temperature, oC (oF)Tstd Standard Temperature, 293K (528oR)Tamb Ambient Temperature, oC (oF)Vcr Critical Orifice Volume, m3 (ft3)Vm Dry Gas Meter Volume, m3 (ft3)Vlc Volume or Mass Liquid Collected in Impingers, ml or gW Width of Duct Cross-Section at Sampling Site, m (ft....)y Dry Gas Meter Calibration Factor
MERCURY SAMPLING EQUIPMENT APPENdIX K SORBENT TRAP MONITORING
METhOd 30B SORBENT TRAP RELATIVE ACCURACY TESTING AUdIT (RATA)
ISOKINETIC SAMPLING EQUIPMENT METhOd 1 dETERMINATION OF SAMPLING LOCATION ANd TRAVERSE POINTS
METhOd 2 dETERMINATION OF STACK GAS VELOCITY ANd VOLUMETRIC FLOW RATE
METhOd 3 dETERMINATION OF EXCESS AIR ANd dRY MOLECULAR WEIGhT
METhOd 4 dETERMINATION OF MOISTURE IN STACK GASES
METhOd 5 dETERMINATION OF PARTICULATE EMISSIONS FROM STATIONARY SOURCES
METhOd 5B NONSULFURIC ACId PM
METhOd 8 SULFURIC ACId MIST & SO2
METhOd 12 INORGANIC LEAd (SZL)
METhOd 13A TOTAL FLUORIdES (SIE)
METhOd 13B TOTAL FLUORIdES
METhOd 17 PARTICULATE BY IN-STACK FILTRATION
METhOd 23 dIOXINS & FURANS
METhOd 26A hYdROGEN hALIdES & hALOGENS
METhOd 29 MULTIPLE METALS
METhOd 201A PM10 EMISSIONS
METhOd 202 CONdENSABLE PARTICULATE MATTER
METhOd 202 CONdENSABLE PARTICULATE MATTER FIGURES
METhOd 206 AMMONIA
METhOd 306 hEXAVALENT ChROMIUM FROM ELECTROPLATING ANd ANOdIZING OPERATIONS
METhOd 316 FORMALdEhYdE FROM MINERAL WOOL ANd WOOL FIBERGLASS NdUSTRIES
METhOd 0010 SEMIVOLATILE ORGANIC COMPOUNdS
METhOd 0011 FORMALdEhYdE, OThER ALdEhYdES ANd KETONES
METhOd 0061 hEXAVALENT ChROMIUM
FLOW, PRESSURE & TEMPERATURE METhOd 2 dETERMINATION OF STACK GAS VELOCITY ANd VOLUMETRICFLOW RATE (TYPE S-PITOT TUBE)
GAS SAMPLING EQUIPMENT METhOd 4A STACK GAS MOISTURE (APPROX. METhOd)
METhOd 6 SULFURIC ACId MIST & SO2
METhOd 6A SULFURIC dIOXIdE, MOISTURE ANd CARBON dIOXIdE
epa reFerenCe methods
METhOd 6B SULFUR dIOXIdE ANd CARBON dIOXIdE
METhOd 11 hYdROGEN SULFIdE IN PETROLEUM REFINERY FUEL GAS STREAMS
METhOd 15A TOTAL REdUCEd SULFUR FROM PETROLEUM REFINERY SULFUR PLANTS
METhOd 16A TOTAL REdUCEd SULFUR
METhOd 18 INTEGRATEd BAG SAMPLING FOR ORGANIC COMPOUNdS
METhOd 26 hYdROGEN hALIdES & hALOGENS
METhOd 106 INTEGRATEd BAG SAMPLING FOR VINYL ChLORIdE
METhOd 308 METhANOL
METhOd 0030 VOLATILE ORGANIC COMPOUNdS (VOST)
METhOd 0031 VOLATILE ORGANIC COMPOUNdS (SMVOC OR SUPERVOST)
METhOd 0040 PRINCIPLE ORGANIC hAZARdOUS CONSTITUENTS (POhCS) USING TEdLAR® BAGS
METhOd 0051 hYdROGEN ChLORINE ANd ChLORINE
GAS ANALYSIS EQUIPMENTMEThOd 3 GAS ANALYSIS FOR ThE dETERMINATION OF dRY MOLECULAR WEIGhT
METhOd 3B GAS ANALYSIS FOR ThE dETERMINATION OF EMISSION RATE CORRECTION FACTOR OR EXCESS AIR
METhOd 7 dETERMINATION OF NITROGEN OXIdE EMISSIONS FROM STATIONARY SOURCES
IRM EQUIPMENTMEThOd 3A dETERMINATION OF OXYGEN ANd CARBON dIOXIdE CONCENTRATIONS IN EMISSIONS FROM STATIONARY SOURCES
METhOd 6C dETERMINATION OF SULFUR dIOXIdE EMISSIONS FROM STATIONARY SOURCES
METhOd 6C dETERMINATION OF SULFUR dIOXIdE EMISSIONS FROM STATIONARY SOURCES FIGURES
METhOd 7E dETERMINATION OF NITROGEN OXIdES EMISSIONS FROM STATIONARY SOURCES METhOd 10 dETERMINATION OF CARBON MONOXIdE EMISSIONS FROM STATIONARY SOURCES
METhOd 25A dETERMINATION OF TOTAL GASEOUS ORGANIC CONCENTRATION USING A FLAME IONIZATION ANALYZER
70
ISOKINETIC SOURCE SAMPLING EQUIPMENT
800-882-3214 / 919-557-7300 www.apexinst.com
Meter Calibration .............................................57Meter Calibration Equipment ...........................57Method 4 .........................................................33Method 4, Accessories ....................................33Method 5, Basic ..............................................34Method 5, Deluxe-Plus ....................................34Method 5, Compact .........................................35Method 5, Heated Filter Assembly ...................35Method 5, 5G ..................................................36Method 5, 5I ....................................................36Method 5, Alternate 5I .....................................36Method 8 .........................................................37Method 8, Accessories ....................................37Method 8, Alternate CTM-13 ...........................37Method 17, Flexible & Rigid.............................38Method 17, In-Stack Filter Assemblies ............39Method 17, Integrated In-Stack Filter Assemblies .............................................39Method 17, Glass In-Stack Filter Assemblies .............................................39Method 23, Deluxe Plus ..................................40Method 23, Sampler Kit Components ..............40Method 23, Coolant Pump Options .................40Method 23, Glassware ....................................40Method 23, Individual Accessories ..................40Method 26A, HCI ............................................41Method 26A, Accessories ................................41Method 29, Multiple Metals .............................42Method 29, Accessories ..................................42Monorails ........................................................60Method 201A, Particle Sizing ..........................44Method 201A, PM2.5 Cyclone Set ..................44Method 201A, Expanded Nozzle Set ...............44Method 201A, PM10 Cyclone Set ...................45Method 201A, PM10 & PM2.5 Cyclone Set .....45Method 201A, Cascade Impactor Set ..............46Method 201A, Particle Sizing Data Reduction WINCIDRS Software ......................................46Method 202, Dry Impinger ...............................47Method 202, Sampling Accessories ................48Method 202, Purge Accessories ......................48Method 0061, Hexavalent Chromium ..............48Nozzle Calibration ...........................................59Nozzles, Isokinetic Sampling ..........................14
Alumina ...........................................................54 Balances .........................................................55-56Ball & Socket Joint Adapters ...........................29-30Ball & Socket Joint Adapters, Impingers ..........29-30Calibration Equipment & Services ..................59Cases, Equipment ...........................................19Cases, Impinger ..............................................21Cases, Risers ..................................................21Cases, Modular Sample Frame .......................21Cases, Umbilical Gooseneck Adapter .............21Cases, Impinger Inlet Strain Relief ..................21Cases, Power Box Adapter .............................21Consoles, XC-5000 Automated Sampling ......4-5 Consoles, XC-522 / XC-572 Manual ..............6-9Consoles, XC-522 Accessories ......................8Consoles, XC-572 Accessories ......................9Consoles, XC-563 Digital Source Sampling ...43Consoles, XC-522 Accessories ......................8Consoles, XC-563 Digital Source Sampling ...10Consoles, XC-563 Audit Kit ............................10Consoles, Method 4 Source Sampling ………11Dessicator & Desiccants .................................53Dessicator & Desiccants, Vacuum Pump ........53Drierite Desiccants ..........................................54Filter Media .....................................................49-50Filter Ovens, Heated .......................................20Filter Ovens, Strain Reliefs ..............................20Filter Ovens, Socket Adapter ...........................20Filter Media, In-Stack Thimbles .......................50Glassware, Sets ..............................................22Glassware, Method 5 Sets ..............................22Glassware, Deluxe Method 5 Sets ..................23Glassware, Accessories ..................................23Glassware, Filter Assemblies/Components .....24Glassware, Individual & Accessories ...............25Glassware, Impinger Accessories ...................25Glassware, Cyclones ......................................25Glassware, Connectors ...................................26Glassware, Controlled Condensate .................26Glassware, Condensers ..................................27Glassware, Adapters .......................................27Glassware, Method 17 ....................................27Glassware, Method 202 ..................................28Glassware, Method 23 ....................................28
Nozzles, Sets..................................................14Nozzles, Oversized.........................................14Nozzles, Unions..............................................15Nozzles, Tube Nuts ........................................15Nozzles, Rings................................................15Nozzles, Vinyl Nozzle Caps ............................15Nozzles, Brushes............................................15Nozzles, Brush Sets .......................................15Nozzles, Ferrules............................................15Nozzles, Small Parts Kit .................................15Nozzles, Steel Alloys ......................................15Ontario-Hydro/Mercury ....................................43Ontario-Hydro/Mercury Accessories ................43Orifice Set .......................................................58Pitot Audit Equipment & Manometers ..............59Probe Assemblies, Method 5 ..........................16Probe Assemblies, Packing Gland .................16Probe, Method 5 Tube Heaters .......................16Probe, Replacement Pitot Tips .......................16Probe Liners ...................................................17Probe Liners, Tubing ......................................17Probe Liners, Adapters ...................................17Probe Sheaths, Method 5 Inconel ..................18Probe Sheaths, Method 5 Stainless Steel .......18Probe Sheaths, Air Cooled Method 5 ..............18Probe Sheaths, Alloy Method 5 .......................18Probe Sheaths, Blowers ..................................18Pump Assemblies, Method 5..........................12Pump Frame, Optional XF-05HW...................12Pumps, Lubricated Rotary Vane .....................12 Pumps, Lubricated Rotary Vane .....................12 Pumps, Diaphragm .........................................13Sample Lines, Heated .....................................32Sample Lines, Unheated Jumpers ..................32Sample Lines, Strain Relief .............................32Sample Recovery ............................................51Sample Recovery, Accessories .......................52Sample Recovery, Bottles ...............................52Silica Gel .........................................................54Umbilical Cables, Split Back ............................31Umbilical Cables, Classic ................................31Umbilical Cables, Classic Adapters .................31Umbilical Cables, Accessories .........................31Wet Test Meters ..............................................58
Isokinetic
www.apexinst.com
919-557-7300 or 800-882-3214Fax: 919-557-7110
Website: www.apexinst.comContact: [email protected]
Apex Instruments, Inc.204 Technology Park Lane
Fuquay-Varina, N.C. 27526, U.S.A.
Mercury & Gas saMplinG cataloG
Software
XC-8U
XC-6000EPC
Doug Bernhardt Customer Service
MERCURY & GAS SAMPLING EQUIPMENT
FLOW, PRESSURE & TEMPERATURE
MERCURY AND GAS SAMPLING SYSTEMS & EQUIPMENT
GAS ANALYSIS EQUIPMENT
APPENDIX
INDEX
ACCESSORIES
ISOKINETIC SAMPLING EQUIPMENT
MercSampler™ Firmware & SoftwareHGCalc Software, Lap-tops ...................4a - 7a
Cabinet Configurations ...............................8a, 9a
Gas Conditioners, Stirling Cooler Glassware & Sorbent Cartridges ................10a, 11a
Audit Kit, Sorbent Traps, Sampler Console Method 30B Source Sampler......12a - 15a
XC-30B, Probes, Probe Accessories ..........16a, 21a
VOST & Method 6, XC-60 Meter Console Type Source Sampler Console ................20a, 23a
Miniature Probes, Versacase ..................24a, 25a
Midget Glassware & Accessories ..........................................26a, 27a
Method 6 (SO2) Supervost Sampling Equipment............28a - 29a
Method 26 (HLC), Gas Sampling Bags, Pump Modules ...30a - 32a
Method 0040, Method 7 Nitrogen Oxides .......................................33a, 34a
Mercury Replacement Parts ..................35a - 41a
Mercury Index ..........................................42a
MERCURY AND GAS SAMPLING SYSTEMS & EQUIPMENT
Please feel free to call our friendly sales staff today!
Vance JonesDomestic Sales,
Customer [email protected]
Janet NicholsSales Manager
John StauberInternational [email protected]
Phone: 919-557-7300 or In the U.S. 800-882-3214Monday-Friday, 8:00 a.m. to 5:00 p.m. (Eastern Time)
Fax: Order at your convenience 24 hours a day, 7 days a week 919-557-7110
Website: www.apexinst.com
Please visit our website for additional product information, new product releases, updated materials, manuals, reference data and valuable links.
mErCUry SamPling EqUiPmEntgaS SamPling EqUiPmEnt Gases in most stacks or ducts often are comprised of small amounts of volatile, potentially toxic compounds in addition to major gas components such as ni-trogen, oxygen, and carbon dioxide. At parts per million levels, most compounds with boiling points below that of water exist in a vapor state. Because gases generally are considered to be well mixed, sampling for constituents in the vapor phase usually is done through a simple probe from a single point of average gas velocity in the stack. A glass wool plug or filter often is used to screen out particulate matter from the gas stream prior to collecting the gas in a sample container or collection vessel.
irm EqUiPmEnt Some of the most common gaseous sampling methods (low flow rate) are Incorporated into 40 CFR Part 60 instrumental reference methods (IRM’s) where specific stationary source pollutants are measured continuously by means of an analytical instrument either to determine compliance with an applicable emission standard or to conduct performance testing of a continuous emission monitoring system (CEMS). The most commonly known instrumental methods are: Method 3A - Oxygen and Carbon Dioxide, Method 6C - Sulfur Dioxide, Method 7E – Nitrogen Oxides, Method 10 – Carbon Monoxide, Method 20 – Nitrogen Oxides, Sulfur Dioxide and Diluent Emissions from stationary gas turbines.
mErCUry SamPling EqUiPmEnt The automated XC-6000EPC MercSampler™ for Sorbent Trap Monitoring Systems is designed for continuous dual sampling of vapor-phase mercury emissions from stationary combustion sources, in accordance with the U.S. EPA MATS pub-lished in 40 CFR, Part 60-63, Appendix A, Subpart UUUUU and is MATS compliant. Performance Specification 12B: Specifications and Test Procedures for monitoring total vapor phase mercury emissions from stationary sources using a Sorbent Trap Monitoring System. These monitoring systems involve continuous repetitive in-stack sampling using paired sorbent media traps with periodic analysis of the time-integrated sam-ples. Persons using PS 12B should have a thorough working knowledge of methods 1, 2, 3, 4, 5 and 30B in appendices A-1 through A-3 and A-8 to this Part 63. Power generation utilities will be able to measure and obtain accurate and reliable mercury emissions data in order to determine emission levels and develop control strategies. Power generation utilities may choose from either Continuous Mercury Monitors or Sorbent Trap Monitors like the Apex XC-6000EPC for Mercury Emissions Monitoring. Apex can provide quality equipment at economical prices for all the catego-ries described above. For over 22 years, Apex Instruments, Inc., has concentrated on manufacturing equipment designed for use in sampling stationary combustion sources. Apex Instruments has always been directly involved with the environmental industry, working close with the U.S. EPA. When the Clean Air Act was enacted in 1990 and hazardous air pollutants were identified for control, Apex Instruments was at the forefront of product design, method evaluation and implementation.
3a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
Gases in most stacks or ducts are often comprised of small amounts of volatile and potentially toxic compounds, in addition to the major gas components of nitrogen, oxygen, and carbon dioxide. Most compounds, at parts per millions level, that have boiling points below water usually exist in a vapor state. Prior to collecting the gas in a sample container or collections vessel, a glass wool plug or filter is often used to screen out particulate matter from the gas stream.
gaSEOUS SamPling
FEATURED METhODSApex Instruments has Gas and Mercury Sampling Equipment for the Following Methods.
METhOD DESCRIPTION
MERCURYMEThOD 30B
Appendix K, Method 30B, RATA for Mercury
METhOD 4A Stack Gas Moisture Approximation
METhOD 6 Sulfuric Acid Mist & SO2
METhOD 6A Sulfur Dioxide, Moisture and Carbon Dioxide
METhOD 6B Sulfur Dioxide and Carbon Dioxide
METhOD 7 Nitrogen Oxides
METhOD 11 Hydrogen Sulfide in Petroleum Refinery Fuel Gas Streams
METhOD 15A Total Reduced Sulfur from Petroleum Refinery Fuel Gas Sulfur Plants
METhOD 16A Total Reduced Sulfur
METhOD 18 Integrated Bag Sampling for Organic Compounds
METhOD 26 Hydrogen Halides & Halogens
METhOD 106 Integrated Bag Sampling for Vinyl Chloride
METhOD 308 Methanol
METhOD 0030 Semi-Volatile Organic Compounds (VOST)
METhOD 0031 Volatile Organic Compounds (SMVOC or SuperVOST)
METhOD 0040 Principle Organic Hazardous Constituents (POHC’S) Using Tedlar Bags
XC-6000EPC MercSamplerTM Console shown
with Stirling Cooler
SK-606 Method 6
XC-30BMercSamplerTM Console
XC-60 Meter ConsoleSK-0031 SuperVost
Featuring the Automated line of
MercSamplerTM Consoles
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 4a
XC-6000EPC mErCSamPlEr™The automated XC-6000EPC MercSampler™ for Sorbent Trap Monitoring Systems is designed for continuous dual sampling of vapor-phase mercury emissions from stationary combustion sources, in accordance with the U.S. EPA MATS published in 40 CFR, Part 60-63, Appendix A, Subpart UUUUU and is MATS compliant. Performance Specification 12B: Specifications and Test Procedures for monitoring total vapor phase mercury emissions from stationary sources using a Sorbent Trap Monitoring System.
These monitoring systems involve continuous repetitive in-stack sampling using paired sorbent media traps with periodic analysis of the time-integrated samples. Persons using PS 12B should have a thorough working knowledge of methods 1, 2, 3, 4, 5 and 30B in appendices A-1 through A-3 and A-8 to this Part 63.
Power generation utilities will be able to measure and obtain accurate and reliable mercury emissions data in order to determine emission levels and develop control strategies. Power generation utilities may choose from either Continuous Mercury Monitors or Sorbent Trap Monitors like the Apex XC-6000EPC for Mercury Emissions Monitoring. For information on the mercury sampling visit: http://www.epa.gov/mercury.
J-hook, page 17
Stirling Coolerpage 11
Monorail, page 17
heated Sample Probe, page 16
heated Umbilical Line, page 17
Flange, page 17
5a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
meets U.S. EPa 40, CFr Part 75, appendix K and method 30B requirements (formerly method 324).
XC-6000EPC MERCSAMPLER™The XC-6000EPC MercSampler™ meter console captures all data necessary for paired sorbent trap sampling according to Appendix K and Method 30B. The meter console controls the sample flow rate proportionally to the stack flow rate and determines the standardized volume extracted through each sorbent trap. To collect the samples, two diaphragm vacuum pumps which work with the proportional valves and mass flow sensors, pull the samples through sorbent traps. Paired samples are extracted from the flue gas for the desired time period, from several minutes to several days. There are optical encoders mounted inside the gas meters to provide digital data for the volume sampled. Samples are then analyzed to determine time-averaged emissions.
Packing list accessories
Specifications
Dry Gas Meters:• Model KG2 series, positive displacement type. • 0.4 liter per revolution.• Optical encoder sensor with quadrature pulse output.• 8 digit LCD Display, 1 cc resolution. • Sample volumes are corrected to standard temperature and pressure, then stored.Sample Pumps:• BTC Diaphragm, Brushless Motor - 12 Vdc, 20” Hg Vacuum, 10,000 hour MTBF, 3900 RPM, Max. PSIG 24”.Sample Flow Control:• Vacuum: 0 to 30” Hg, 0 to 101 kPa, 2% accuracy.• Stainless steel sample manifolds fitted with mass flow sensors, vacuum sensors, and proportional valves.• Proportional or constant flow sampling.• Mass Air Flow: proportional flow control, 100 to 2000 ccm, port style, manifold mount.• Proportional Valve: Voltage Sensitive Orifice (VSO), 12 Vdc.Data Acquisition Control Board (DAC): • Enhanced Flash 16 bit RISC based microcontrollers; main and Digital Signal Processing (DS). Real time clock with auto backup and write protection to external SRAM.• High Speed 14bit A/D convertor with parallel DSP interface.• 1 GB SD Memory Card for data storage – stores up to 99 tests (30 day test runs). Embedded Ethernet Port with full TCP/IP Protocol and 256 bit encryption.• USB 2.0 Comm Input connection.
Thermocouple Multiplexer:• Accepts Type K Thermocouple inputs; input protection includes gas discharge tubes for ESD and surge protection.• 11 Pic Microcontrollers, 1 for each channel and MUX circuitry• MUX Circuitry to receive multiple inputs and transmit selected output.• 10 microcontrollers, one for each optically isolated channel.Integrated Temperature Control:• Designed into DAC for probe/trap heat control output via 25 amp SSR.Barometric Pressure: 600 to1100 mbar, 17.7 to 32.4”Hg, temperature compensated, amplified output.Communications:• PC user interface via Ethernet, USB, or optional wireless router• Remote access and control via onboard configurable router to owners Network Computer.• Optional TCP/IP MODBUS (ASCII or RTU) Communications to the DAS.• Optional interface to DAS system via TCP/IP Modbus.Weight: 34 lbs. (15.5 Kg).Dimensions: HxWxD 14” x 19” x 15.5” (35.56 cm x 48.26 cm x 39.37 cm).
The XC-6000EPC MercSampler™ simplifies most sampling require-ments by automating data acquisition, sample flow adjustments, leak checks, calculations, temperature control, and calibrations. Data is easily transferred to a Microsoft Windows XP-based PC through Ethernet, USB or an optional Wireless Interface.
XC-6000EPC
XC-6000EPC MercSampler™ Console
Features• Customer-Friendly Software and Firmware• Easy Data Export (Text and CSV files)• Configurable System Alarms (Dry Contact Closure/Piezo Alert)• Quarterly Audit Calibration Check (Optional Audit/Cal Kit)• Remote Input for External Test Pause and Resume
Installation: 19” Rack Mount Standard. Available 8U Transport case, ShockMount Rack or Weather Resistant Aluminum Cabinet Configurations.
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 6a
MercSampler™ SOFTWAREMercSampler™ Automated Software works with a windows based platform. It allows the operator to quickly set up test profiles, perform sample runs, sensor calibration, DGM calibration, run quarterly audits and download test data at any time during or after a test run. Software can be purchased separately for use with customer supplied computer. Intuitive windows based operator interface may be run from local PC or remote network connection.
XC-6K-SW
MercSampler™ FIRMWARE:The Apex Instruments specifically engineered firmware (embedded software) has been designed to utilize the technical features of the RISC based Microchip microcontrollers. RISC microcontrollers provide decision making as well as precise “autonomous” control of the console while the laptop or PC is not connected. Microcontroller Hex code is easily updated in the field with a simple executable program and a programming interface cable which allows for continued enhancements and upgrades of the product.
Test Profile/Configuration Set-upCustomize test setup with the user defined profiles & configurations, or use the default set-tings which can be stored & retrieved.
Pre & Post Leak Test:Automated pre-test leak check with variable vacuum, and an auto-mated post-test leak check with vacuum, regulated to the maximum vacuum recorded during test.
Active Test Data:Real-time test screen enables the user to see instantaneous & /or cumulative data in an easy-to-read graphic display screen or raw text.
Calibration:Simple and easy to follow steps to fully calibrate all required components. This application provides electronic documentation stored with each test run.
Alarm:Multiple alarm configu-rations for tolerance, signal loss, idle time out, thermocouple in-puts and power failure.
MercSampler™ Software Screens
MerSampler Firmware Diagram
Computer Recommendations:Processor: 1.80 GHz or faster
Memory: 1 G, DDR2, 533MHZ
hard Drive: 40 G or greater, 5400 RPM SATA
Port: Ethernet Ready and USB 2.0
Optical Drive: CD-RW/DVD Combo (CD Required)
Software: Microsoft Windows XP, SP2 (Framework. net 3.5, Microsoft Office Installed, Adobe Reader)
Wireless: 1390 802.11 G Mini Card
Screen: Resolution 800 x 600, 14”
7a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
hgCalc Software
hg Calc Capabilites:Application used to import XC-6000 sample run data and trap analysis data to perform calculations for Appendix K. Sold separately.
The hgCalc Software uses sample run data and trap analysis. The sample run data from the MercSampler™ XC-6000 is imported into the application, where total mercury mass, hourly and total mercury emissions are calculated. The software insures the specifications in 40CFR, part 75 are met. The software will also verify QA/QC specifications regarding Section 2 breakthrough, relative deviation, and Section 3 spike recovery as shown in Appendix K, table K-1.
When all calculations are complete and data verified this can be exported currently in Excel, Comma Separated Values (CVS), Text/PDF format and will be available in an XML report format in the near future.
6K-HgCalC
Durabook Features• Intel Core-Duo T2080 - 1.73 GHz• 14.1” TFT 1024 x 768 Screen • WindowsXP/Vista Capable • 80GB SATA, 5400 pm• Intel® Graphics Media Accelerator (GMA)• 1024 MB DDRII• Spill resistant Keyboard (85 keys)• 6 Cell Lithium-Ion Battery
DurabookThe LT-D14RY Series has a magnesium case with four corner bumpers to protect internal components, a spill resistant keyboard with insulation, and anti-shock around the system’s vital components offering protection from drop and concussion. Optional sunlight readable screen is also available. One year warranty. Dimensions: HxWxD: 1.5” x 12.3” x 10.1” (3.81 cm x 31.2 cm x 25.7 cm). Weight: 5.73 lbs. (2.6 kg.)
Acer Aspire One NetbookAcer Aspire One AOD255E-13429 Diamond Black Intel Atom N455 (1.66GHz) 10.1” WSVGA 1GB Memory 250GB HDD Netbook.
lt-a
Features• OS Provided - Windows 7 Starter• Diamond Black Color• Resolution 1024 x 600• LED backlight & Acer CrystalBrite Technology• Intel GMA 3150• Chipset - Intel NM10• CPU L2 Cache - 512KB
Processor: CPU Type - Intel Atom CPU Speed - N455 (1.66GHz) CPU L2 Cache - 512KB Display: 10.1”, WSVGA Wide Screen Display (1024x600)Memory: 1GB DDR2 SDRAM hard Drive: HDD - 250GB, 5400RPM SATA Hard Drive Graphic Processor: Intel GMA 3150 Power: 3-cell Li-ion Battery (2200 mAh), Battery Life - up to 4 hours Dimensions: 10.17” x 7.28” x 0.95”, Weight - 2.43 lbs. Communications: LAN - 10/100Mbps WLAN - 802.11b/g/n Wireless LAN Netbook Camera: Built-in Camera Pixels - 0.3 Megapixel Expansion / Connectivity: 3 x USB 2.0, Video Ports - 1 x VGA, Audio PortsCard Reader: 2-in-1 Digital Media Card Reader- Secure Digital (SD) Card, MultiMediaCard (MMC) Video Memory: Shared system memory, Memory Slots - 1 x 204-Pin DDR3 SO-DIMM
LAPTOPSThe human Machine Interface to the MercSampler™ Console is the Apex MercSam-pler™ Intuitive software utilizing a Windows based PC/laptop. The system is available with several different laptop models available at Apex Instruments; Durabook, Durabook with sunlight readable screen, or the DELL Inspirion Mini 10 Netbook.
lt-D14ry-DB with Sunlight readable Screen
lt-D14ryNetbook - Call for Details
LT-D14RY
LT-A
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 8a
The internal frame of the ShockMount Rack Case is mounted on revolutionary adjustable elastomer shock absorbers on all eight corners, designed to control the effects of shock and vibration on three axes. Includes rails, wiring, and hardware for console and gas conditioner installation. The “sway” space around the internal frame provides natural air conditioning. The configuration is suitable for use in a semi-protected area, such as annulus. Dimensions: HxWxD: 36.25” x 29.25” x 27.25” (92 cm x 75 cm x 70 cm); Empty Weight: 84 lbs. (38.1 kg).
XC-16USa
Features
• 19” Polyethylene Roto Molded Shell• Front and Rear Covers• Molded-in Handles • Adjustable Elastomer Shock Technology• Corrosive Resistant Polyethylene• Accepts 500 mL Bottles
Assembly includes: Rails, Wiring and Hardware to accept XCP-6000ECP and SGC-4000HG
XC-16USA Shockmount Case
ShockMount Rack Case Assembly
Shown with XC-6000EPC Meter Console and SGC-4000hG Stirling Gas Conditioner
MercSampler™ Cabinet ConfigurationsAfter 20 years in the industry, Apex Instruments recognizes the wide variety of customer site conditions and offers a range of equipment installation solutions. Apex Instruments has the experience and ability to custom engineer carry cases and cabinets to best suit any application. The installation solutions range from basic components that can be installed in an existing instrument control room, rackmount cabinets or environmental trailers, to self-contained meter console/gas conditioner systems that can be installed in a plant stack annulus or on a stack platform. Call for customization.
XC-8U Transport CaseThe XC-8U Transport Case has a tough exterior for durability. Multiple features help the case protect valuable products from a fall, tumble or rough landing. Dimensions: HxWxD: 18” x 22” x 20” (45.7 cm x 55.9 cm x 50.8 cm);Emty Weight: 21 lbs. (9.5 Kg).
XC-8U
Features
• 19” Black Polyethylene Roto Molded Shell• Front and Rear Covers• Molded-in Handles • Shock Absorbing Rubber Feet• Recessed Heavy-Duty Twist Latches• Replaceable Steel Thread Front Rails• Optional Rear Rails Available
XC-8U Transport CaseShown with Rack Mounted
XC-6000EPC MercSampler™Meter Console installed.
Custom Packaging Available. Call for details!
9a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
66” Enclosure with XCP-AC
XCP-ACCR-60 Enclosure Cabinet60-inch upright cabinet, 19” rack. Complete with removable louvered side panels and doors, 19”rack mounting rails, internal equipment drawer slides for XC-6000 Console and SGC-4000 Chiller (sold separately), integral slide tray for laptop or work-space, pre-wired with convenient duplex outlets and top or side sample line and power cable entry. (Not for outdoor service). Dimensions: 60” (cm) x 19.125” (cm) x 24” (cm). Weight: ~160 lbs. (72.57 kg).
Cr-60
CR-60-NV Enclosure Cabinet60-inch upright cabinet, 19” rack. Complete with Non-Ventilated side panels and doors, 19”rack mounting rails, internal equipment drawer slides for XC-6000 Console and SGC-4000 Chiller (sold separately), integral slide tray for laptop or work-space, pre-wired with convenient duplex outlets and top or side sample line and power cable entry. Dimensions: (HxWxD): 60” (cm) x 19.125” (cm) x 24” (cm). Weight:~160 lbs. (72.57 kg).
Cr-60-nV
Features• EMI/RFI Suppressor • Internal Corrosion Protection• Two Stage Thermostat• Maintains NEMA 12/3R Rating
Air Conditioner Air Conditioner keeps the cabinet at operating temperature while keeping out dust, fumes, oil and other contaminants. It operates continuously with a two stage thermostat to ensure a longer compressor life and maintain a 6° temperature range. The integral heater kit includes a thermostat and limiter for frost protection.
Capacity: 2000 BTU/H, 1500 BTU/H at 95°F (35°C).Temperature: Maximum 131°F (55°C), minimum -20°F( -28°C). Power: 115/100V, 60/50HZ.Weight: 35 lbs. (15.87 kg).
CR-66-NV Enclosure Cabinet66-inch upright cabinet, 19” rack. Complete with Non-Ventilated side panels and doors, 19”rack mounting rails, internal equipment drawer slides for XC-6000 Console and SGC-4000 Chiller (sold separately), integral slide tray for laptop or work-space, pre-wired with convenient duplex outlets and top or side sample line and power cable entry. Dimensions: (HxWxD): 66” (cm) x 19.125” (cm) x 24” (cm). Weight: ~165 lbs. (74.84 kg).
Cr-66-nV
XCP-AC
XCP-AC Optional Air Conditioner (includes integral heater for frost protection).
XCP-aC
Features• Powder Coated Aluminum• Easy Access Door• Durable Compact Design• Optional Heating and Cooling System• Accepts up to 1000 mL Bottles
MercSampler™ Cabinet Configurations
Aluminum Environmental CaseThe CR-I8U Aluminum Weather Resistant Environmental Case is compact, heavy-gauge Aluminum w/ Weather resistant Powder Coat Paint (internal 19” Rack mount) for meter console and Stirling gas conditioner. Dimensions: HxWxD: 37” x 21” x 21” (93.9 cm x 53.3 cm x 53.3 cm);Weight: 150 lbs. (68.03 kg). Weight with AC Unit: 185 lbs. (83.91 kg).
Cr-18U Cr-18U-aC Crt-18U-aC
XCP-ACCR-18U
AC option installed on 18U cabinet
CR-18U-AC CRT-18U-ACPermanent
transportable cabinet
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 10a
GAS CONDITIONERS
Features• FPSC Chiller Module uses Environmentally Safe Helium Gas as a Refrigerant, no CFC’s.• The Module is Hermetically Sealed in Stainless Steel Casing for Fast and Easy Installation or Replacement as Necessary. • The Cold end of the FPSC is Inserted Directly into a Machined Anodized Aluminum Chiller Block. • C276 Hastelloy Serves as the Reverse Flow Condensate Separators.• Six Times Efficiency of Thermoelectric (peltier) Coolers.• Uses Less than 40w of Electricity.
• 12 V DC Power Supply.
The Apex Instruments SGC-4000hG Stirling Gas Cooler is specially designed for removing moisture and acid gases from flue gas samples. This new gas cooler uses an industrial grade super efficient Free Piston Stirling Cooler (FPSC) for chilling the sample gas to remove moisture. The Stirling will provide a robust, closed, dual channel gas conditioning system to deliver dry, acid free gas to the meter console. No peristaltic pumps to leak.
SgC-4000Hg
Optional 10U roto molded rack mounted CaseThe new US Series is the ultimate in American technology with its roto molded tuff shell, front and rear lids, recessed heavy-duty twist latches, molded in handles, shock absorbing rubber feet and the recognizable patented deep Roto-X pat-tern for solid stackability. The unique molded in unbendable valance and steel threaded rails with self tapping screws make the US Series racks convenient to use and the most durable. Dimensions: HxWxD: Outside Dimensions: 20.5” x 23.75” x 22” (52.07 cm x 60.32 cm x 55.88 cm). Weight: 20.46 lbs (9.28 kg).
XC-10UD
Specifications
Digital Temperature Control: +/- 1 OC, LED DisplayInlet and Outlet Temperature: Typical Inlet Temperature: 250-3000 F (Heated Lines Set Point).Cooling Capacity: >40 wattsDual Path Cooling Block: Anodized Aluminum.Condensate Bottle: 1000 ml (plastic coated glass).Acid Scrubber Cartridges: 2 ea. 2-5/8” s 11-3/8” Polycarbonate with Aluma-Sorb; 1/8” Stainless Steel FNPT fitting.
Reverse Flow Condensate Separator: C276 Hastelloy 1” OD x 4” Active Zone.Maximum Flow Rate: 2 lpm at 20% H2O Channel.Freeze Protection: 80w Heater. Ambient Operating Temperature: 0 to 500 C.Power Requirements: 120 V AC/2.5 amps.Dimensions: Without Bottles: HxWxD: 17”x16”x7” (43.2 cm x 40.6 cm x 17.8 cm).Weight: 25 lbs (11.3 kg).
Features• Roto molded uni-body construction• Threaded steel rails• Rear rails included• Interlocking X pattern for solid stackability
• Front and rear full size lids• Recessed latches• Molded-in handles• Shock absorbing feet
10U Molded Rack Case
SGC-4000hGStirling Gas Cooler
Shown with XC-6000EPC
11a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
Portable Stirling CoolerThe SGC-4000hGP Stirling Cooler Gas Conditioner Portable Unit comes with a top handle for easy transport and a durable UHMW polyethylene 6U case with condensate collection bottles. Any of the configurations are suitable for use with the Appendix K Mercury Sorbent Trap Sampling System. Dimensions: HxWxD: 22” x 13” x 23” (55.88 cm x 33.02 cm x 58.42 cm). Weight: 32 lbs (14.5 kg) without sorbent.
Portable Unit SGC-4000SgC-4000HgP (110V)SgC-4000HgP-V (240V)
Portable SGC-4000hGP
Alumina Sorbent is an activated alumina/silica gel primarily used for air drying, acid scrubbing and low temperature applications in the stirling sorbent cartridge. 5.5 lbs (2.5 kg) container (80% alum-sorb, 20% silica gel).
alUma-SOrBALUMA-SORB
Model DescriptionSC-30B 2 AlumaSorb cartridges, 2 in-line filters with drains & disposable
filter elements in Enclosure with sample line inputs/sample out-puts, dual stream, designed for use with XC-30B system.
SC-30B
GSB-1000L
Glassware and Sorbent Cartridges
GA-GL-45Sand GA-GL-45B
GSB-500SCGSB-1000SC
Model DescriptionGSB-1000SC Sample Bottle, Clear Glass, GL-45 Threaded, 1000mL,
Safety Coated for Condensate Collection. Requires: GA-GL-45B Cap and GA-GL-25S Seal.
GSB-500SC Safety Coated Sample Bottle, 500mL,
GSB-1000SCA Sample Bottle Assembled, Clear Glass, GL-45 Threaded, 1000mL, Safety Coated for Condensate Collection. Assembly Includes GA-GL-45B Cap and GA-GL-25S Seal.
GSB-1000L Bottle Sample, L-Shape, Clear Glass, GL-45 Thread, 1000mL (Not Safety Coated).
GA-GL-45S Seal for 1000mL Bottles.
GA-GL-45B Bored Cap, #45 Threads.
GSB-1000SCGSB-500SC
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 12a
MercSampler™ Audit KitThe Apex Instruments AK-6000 MercSampler™ Audit Kit is designed for Appendix K and Method 30B compliance auditing of the XC-6000 MercSampler™ System. The kit includes a single or dual secondary reference meter console. Single kit is in a rugged 4U X-Case with a molded-in handle for easy transport. Dual kit comes with 8U black polyethylene molded case. Use with software version 80620-94 or later.
MercSampler™ Audit Screen Shot
Compatible with the MercSampler™ Software DGM-AP25SRD Reference Dry Gas Meter
with Optical Encoder:Digital Display: 8 Digit LCD, resetable. Durable: Built in a rugged 4U X-Case with molded-in handles for easy transport. Calibration: 15-point (Secondary Reference).Vacuum Gauge: 2.5” Face, Range: 0-30” Hg, 1% Accuracy.Single Dimensions: HxWxD: 21” x 9.5” x 14” (53 cm x 24 cm x 35.5 cm); 22 lbs (10 kg).
Can be used with XC-6000EPC MercSampler™ and XCP-6000EPC Portable Console
Packing List6” Thermocouple Y AdaptertCa-6yHg
36” Thermocouple Type KtCa-36Hg
m5C-520
• NIST Traceable• Handheld • Type K, °F or °C • Range: -409° to 2501.6° F (-245 to 1372° C) • Accuracy: 0.5° F (+0.25°C) for Type-K • Output resolution by 0.1° F or °C• Easy Dial Knob
Thermocouple Simulator handheld Digital Barometer• NIST Traceable • 15.9-31.01” Hg, Resolution: 0.03” Hg; 400-1070 mbar, Resolution: 1 mbar. • Altitude: -500 - 7000m, Resolution: 1m
Bar-4198
Insulated Ice Bath• Vacuum Insulated• Stainless Steel • Capacity: 16 oz.
aK-6tH16
handheld Waterproof Thermometer• NIST Traceable • Waterproof • Range: –58° to 572° F (–50° to 300°C) • Resolution: 0.1° from –20° to 200° • Accuracy: ±0.4°C or ±1.5°C
DPt-168-niSt
Secondary Reference Meter
Dgm-aP25SrD
Single Audit Kit
aK-6000
Single Audit Kit Accessories (Included):
aK-6000-Cal Annual Verification and Certification of the AK-6000 Audit Kit. Includes 15-point Calibration of the Reference DGM; Verification of Vacuum Gauge, Digital Barometer and Thermometer; System Inspection; and System Test.
13a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
Description
Size (mm) O.D. x L
StackCondition* Sections
Section Breakdown
Part Number
Mercury Trap, App K, Standard, Unspiked
10 x 185 Research or Baseline Testing
3 Sections .5 grams carbon each section
MTK-U
Mercury Trap, App K, Standard, 3rd Section Spiked - spike level desired ng
10 x 185 Standard 3 Sections .5 grams carbon each section
MTK-So
Mercury Trap, App K, High Temp, 3rdSection Spiked - spike level desired ng
10 x 185 High Temp 3 Sections .7 grams carbon 1st section, .5 grams section 2 & 3
MTK-H-So
Mercury Trap, App K, Acid Gas, 3rdSection Spiked - spike level desired ng
10 x 185 Acid Gase 3 Sections 5 grams sorbentconditioning pre-sec-tion, .5 grams carbonsection 1, 2 & 3
MTK-A-So
Mercury Trap, App K, High Particulate, 3rd Section Spiked - spike level desired ng
10 x 185 HighParticulate
3 Sections Inert pre-filter,.5 grams carbonsection 1, 2 & 3
MTK-P-So
Mercury Trap, App K, RATA, 3rd Section Spiked - spike level desired ng
10 x 185 Relative Accu-racy Test Audits
3 Sections .3 grams carbon each section
MTR-So
Long Term Mercury Traps (Appendix K)
Standard Spike Levels Range from 1,000 ng to 20,000 ng - CUSTOM LEVELS AVAILABLE
Section 3 Spiked
Section 2 Breakthrough
Section 1 Sample Collection
appendix K / PS 12B specifies sampling, and analytical, and quality-assurance criteria and procedures for the performance-based monitoring of vapor-phase mercury (Hg) emissions in combustion flue gas streams, using a sorbent trap monitoring system. The principle employed is continuous sampling using in-stack sorbent media coupled with analysis of the integrated samples. The performance-based approach of Appendix K allows for use of various suitable sampling and analytical technologies while maintaining a specified and documented level of data quality through performance criteria.
method 30B is a procedure for measuring total vapor-phase mercury (Hg) emissions from coal-fired combustion sources using sorbent trap sampling and an extractive or thermal analytical technique. This method is only intended for use only under relatively low particulate conditions (e.g., sampling after all pollution control devices).
mercury Sorbent traps
apex trap Features:• High Capacity Impregnated Carbon• Low Mercury Background Levels• Custom Spiking Available
• Textured, Easy Grip Caps will ensure Accurate Leak Checking• Protective Transport Tubes
Mercury Trap Legend
MT
Method 30 B
Type Option Spiking
K Appendix KR Appendix K RATA
High TemperatureAcid GasHigh Particulate
HAP
High Temperature& Acid Gas
C
SpeciatedS
Example: MTB-H-S1000Mercury Trap, Method 30B,High Temperature, Spiked at 1000ng
UnspikedUSpiked (Indicate ng Amount)S
*Stack Condition Key RATA Relative Accuracy Test Audits of App K Sampling Systems Standard Stack Temp 200-400oF, SO2 Level < 500PPM Acid Gases Stack Temp 200-400oF, SO2 Level > 500PPM high Temp Stack Temp > 400oF, SO2 Level < 500PPM high Temp & Acid Gas Stack Temp > 400oF, SO2 Level > 500PPM
Any trap can be customized for special stack conditions. For high particulate and wet stacks, we recommend using the Apex Sorbent Trap Shield to reduce sorbent trap plugging.
• Chain of Custody Included• Long Term Storage• Variable Testing Duration
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 14a
Description
Size (mm) O.D. x L
StackCondition* Sections
Section Breakdown
Part Number
Mercury Trap, 30B, Standard, Unspiked
10 x 185 Standard 2 Sections .3 grams carbon each section MTB-U
Mercury Trap, 30B, High Temp, Unspiked
10 x 185 High Temp 2 Sections .5 grams carbon 1st section, .3 grams carbon 2nd section
MTB-H-U
Mercury Trap, 30B, Acid Gas, Unspiked
10 x 185 Acid Gases 2 Sections .5 grams sorbent conditioning pre-section, .3 grams carbon each section
MTB-A-U
Mercury Trap, 30B, High Temp/ Acid Gas, Unspiked
10 x 185 Acid Gases & High Temp
2 Sections .5 grams sorbent conditioning pre-section, .5 grams carbon 1st section, .3 grams carbon 2nd section
MTB-C-U
Mercury Trap, 30B, Standard, 1st Section Spiked - spike level desired ng
10 x 185 Standard 2 Sections .3 grams carbon each section MTB-So
Mercury Trap, 30B, High Temp, 1st Section Spiked - spike level desired ng
10 x 185 High Temp 2 Sections .5 grams carbon 1st section, .3 grams carbon 2nd section
MTB-H-So
Mercury Trap, 30B, Acid Gas, 1st Section Spiked - spike level desired ng
10 x 185 Acid Gases 2 Sections .5 grams sorbent conditioning pre-section, .3 grams carbon each section
MTB-A-So
Mercury Trap, 30B, High Temp/ Acid Gas, 1st Section Spiked - spike level desired ng
10 x 185 Acid Gases & High Temp
2 Sections .5 grams sorbent conditioning pre-section, .5 grams carbon 1st section, .3 grams carbon 2nd section
MTB-C-So
Short Term Mercury Traps (Method 30B)
Speciated Mercury Measurement of Flue Gas Requires use of Air Cooled Probe
Description
Size (mm) O.D. x L
StackCondition* Sections
Section Breakdown
Part Number
Mercury Trap, 30B, Speciated, Unspiked
10 x 300 Evaluation & Research
4 Sections .7 grams KCl section 1 & 2, .3 grams carbon section 3 & 4
MTB-S-U
Flue gas Oxidized Hg (Hg2+) species are adsorbed by a potassium chloride (KCl). After passing through the KCl sorbent, Elemental Hg (Hgo) is collected by iodated carbon sorbent. Total Hg (Hgt) is determined by summation of species.Proper temperature maintenance is critical (<130°C) for accurate speciation results. Sorbent trap shields are used to prevent buildup of particulate, which can potentially oxidize mercury creating a bias.
Speciated Mercury Trap
mercury Sorbent traps
Elemental hg (hgo)Section 3 Section 4 Breakthrough
Oxidized hg (hg2+)Section 1 Section 2 Breakthrough
Section 2 Breakthrough
Section 1Sample Collection
15a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
The XC-30B MercSampler™ Console, designed especially for performing Method 30B, simplifies sampling requirements by automating data acquisition, sample flow adjustments, leak checks, calculations, temperature control, and calibrations. Data is easily transferred to a Microsoft Windows Based PC through USB Interface. The XC-30B MercSampler™ performs dual sorbent trap sampling at flow rates up to 2.0 lpm. Can be operated with your choice of probes and gas conditioning systems, including our popular SGC-4000HGP Stirling Gas Conditioner.
Method 30B SourCe SaMpling SySteM
A Typical System Includes:• Automatic Console: XC-30B Sampling Console / with Netbook
(Alternative Option: Manual XC-260 Console Series)• Gas Conditioner: Portable versions
• Stainless Steel Probe: Optional length with single heater, for dual sample traps.• Umbilical: Heated line, specify length
portable gas Conditioner
heated dual trap Sample probe
heated umbilical
line
automated XC-30B MercSampler™ Console with netbook Computer and MercSampler™ Software
Please contact your sales representative for more details.
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 16a
The XC-30B MercSampler™ Console, designed especially for performing Method 30B, simplifies sampling requirements by automating data acquisition, sample flow adjustments, leak checks, calculations, temperature control, and calibrations. Data is easily transferred to a Microsoft Windows Based PC through USB Interface. The XC-30B MercSampler™ performs dual sorbent trap sampling at flow rates up to 2.0 lpm. Can be operated with your choice of probes and gas conditioning systems, including our popular SGC-4000HGP Stirling Gas Conditioner.Please contact your sales representative for more details.
XC-30B MERCSAMPLER™ CONSOLE
Automated XC-30B MercSampler™ Console &
Netbook Computer
Features• Fully Automated for Paired Sampling• Dual Dry Gas Meters and Mass Flow Sensors• Alerts for Port and Traverse Point Changes• Simple Data Export• Compact Portable System• Eight Isolated Type K Thermocouple Channels• USB Interface• Easily Configured with Windows Based PC
Specifications
Dry Gas Meters:• Dual dry gas meters with integrated optical encoders, resolution to 1 cc• Model KG2 positive displacement type. • 0.4 liter per revolution.• Optical encoder sensor with quadrature pulse output.
Sample Pumps:• Dual Head Miniature Diaphragm Pumps with 12 VDC motors, Max Vac. 22” HgSample Flow Control:• Stainless steel sample manifolds fitted with mass flow sensors, vacuum sensors, and proportional valves.• Constant flow sampling.• Mass Air Flow: Flow control, 300 to 2500 ccm• Proportional Valve: Voltage Sensitive Orifice (VSO), 12 Vdc.
Data Acquisition Control Board (DAC): • Enhanced Flash 16 bit RISC based microcontrollers; main and Digital Signal Processing (DS). Real time clock with auto backup and write protection to external SRAM.• High Speed 14bit A/D convertor with parallel DSP interface.• 1 GB SD Memory Card for data storage – stores up to 99 tests • USB 2.0 Comm Input connection.
Communications:• PC user interface via USBThermocouple Multiplexer:• Accepts Type K Thermocouple inputs; input protection includes gas discharge tubes for ESD and surge protection.• 11 Pic Microcontrollers, 1 for each channel and MUX circuitry• MUX Circuitry to receive multiple inputs and transmit selected output.• 10 microcontrollers, one for each optically isolated channel.Integrated Temperature Control:• Designed into DAC for probe/trap heat control output via 25 amp SSR.Pressure: Barometric Pressure • 600 to1100 mbar, 17.7 to 32.4”Hg, temperature compensated, amplified output.
Vacuum • 0 to 30” Hg, 0 to 101 kPa, 2% accuracy• Durable UhMW Polyethylene Case: Built-In Handles (Size 10U) 19” Rack Mount Panel• AC Power: 120 Vac 60Hz. / 220 Vac 50Hz• Dimensions: 23in x 21in x 12in (58cm x 53cm x 30.5cm)• Weight: 39 lbs. (17.7kg)
XC-30B with netbook
XC-30B-V with netbook
XC-30B-V no netbook
Advanced Microprocessor Control
17a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
XC-260 SOURCE SAMPLER CONSOLEThe Apex XC-260 Source Sampler is a low-price, portable, field-proven meter console that is easy to use, and ideal for sampling mercury emissions based on CFR 40, Part 60, Method 30B.
The heart of the Apex Instruments manual system is the XC-260 Source Sampler, a precision meter console used for collecting Hg emissions. The average mercury concen-tration for the sampling period is determined by using the sample volumes measured by the dry gas meters and the results of the sorbent trap analysis.
Two flow rate configurations are offered; 0.2 to 2.4 litersper minute or 100-1000 cubic centimeters per minute.
XC-260 Manual Source Sampler Console
Features• Dual Independent Flow Paths• Dual Dry Gas Meters with Digital Displays• Coarse and Fine Valves for Precise Flow and Vacuum Control• Stainless Steel Valves and Fittings• Stainless Steel 1/4” Quick Connects• Digital Temperature Controller for Probe Heater • Elapsed Digital Timers • Dual Scale Vacuum Gauges• Durable Polyethylene Case with Built-In Handles (size 10U)
Sampler also ideal for method 18.
Model Description
XC-260 Source Sampler 0.2-2.4 lpm flow rate (120 VAC)
XC-260-V Source Sampler 0.2-2.4 lpm flow rate (240 VAC)
XC-260-A Source Sampler 100-1000 cc/min. flow rate (120 VAC)
XC-260-AV Source Sampler 100-1000 cc/min. flow rate (240 VAC)
XC-260-C Source Sampler 4.0 lpm. flow rate (120V)
XC-260-CV Source Sampler 4.0 lpm. flow rate (240V)
Consoles
Specifications
Dry Gas Meters: Model 25 Series, positive displacement diaphragm type, 0.7 liters per revolution, optical encoder sensor with quadrature pulse output, gas volume totalizer with an eight digit LCD display, 1 cc resolution (standard).Dual Diaphragm Sample Pumps (2): 12 VDC motors, Max Vac. 20” Hg.Probe Temperature Control: Compact, 1/32 DIN auto tuning indicating temperature controller with external 25 amp solid state relay. 115 VAC outlet 5-15R, Standard Type-K jack for input.
Digital Temperature Display: 3.5 Digit Display °F (-157°F to 1999°F), display and controller are resettable for °C upon request (OC is standard for export). Thermocouple Inputs: Five external Type K inputs plus two Type-K Internal Gas Meter connections.Flowmeters: Solid Machined Acrylic (0.2 - 2.4 lpm) *Optional 100-1000 ccm (XC-260A).AC Power: 120 V/60 Hz or Optional 220 V/50 Hz.Dimensions: 23” x 21” x 12” (58 cm x 53 cm x 30.5 cm).Weight: 39 lbs. (17.7 kg).
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 18a
FlangePF-4/40CLS
OptionalJ-hook
hGP-1SJ
Air Cooled ProbehGPA-o-hS
XC-6000 CabinetCR-18U-AC
MercSampler ConsoleXC-6000
Stirling Gas Conditioner
SGC-4000hG
hosehGBh-o
Trolley / ChainP2751
Packing GlandPG-32/40CL
BlowerhGB-93CFM
AirConditioner
XCP-AC
Cement maCt Compliant
PS 12 (Appendix K) and Method 30BProbes come in standard lengths of 4’, 6’ and 9’. PS 12 (Appendix K) Probes are constructed from Alloy C276 for long-term use in extremely corrosive conditions. Type-K thermocouples are used to monitor, trap, stack and probe temperatures. Method 30B Probes come standard in stainless steel with Type-K thermocouples to monitor trap and stack temperatures. Both probes are designed for two 10 mm diameter traps (smaller trap adapters also available). The paired sorbent traps are inserted at the inlet end of the probe, using leak tight compression fittings before inserting directly into the flue gas stream.
MERCURY PROBES
The probe is heated to prevent any liquid condensation in the sorbent traps. An insulated, powder-coated aluminum probe head enclosure minimizes condensation at the junction between the probe and the heated umbilical/sample line.
reliable and Easy to Use With quick Set-Up time
19a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
Probe Length(feet)
Replace -�- with Probe Length Single heater for HGP�HS
Dual heaterHGP�HD
4 4’ Stainless Steel Heated Probe with 2” Outer Sheath, Type K Thermocouples, 1/2” Sample Lines, Insulated Probe Head Junction Enclosure; 120VAC
6 6’ Same as above
9 9’ Same as above
12 12’ Same as above
METhOD 30B STAINLESS STEEL PROBES
Probe Length(feet)
Replace -�- with Probe Length Dual heaterHGP�HCD
Dual heater withPitot HGP�HCDP
4 4’ Alloy C276 Heated Probe with 2” Outer Sheath, Type K Thermocouples, 1/2” Sample Lines, Insulated Probe Head Junction Enclosure; 120VAC
6 6’ Alloy C276 Heated Probe - Same as above
9 9’ Alloy C276 Heated Probe - Same as above
12 12’ Alloy C276 Heated Probe - Same as above
APPENDIX K ALLOY C276 PROBES
Part Number hG, Air Cooled heated Probe, Stainless Steel with Single heaters
HGPA-4-HS 4 Foot, Air Cooled Mercury Probe
HGPA-5-HS 5 Foot, Air Cooled Mercury Probe
HGPA-6-HS 6 Foot, Air Cooled Mercury Probe
HGPA-AI6 Air inlet for plant air, 3/8 fnpt, Sanitary cap with pipe thread
NEW AIR COOLED MERCURY PROBES
Part Number
hG, Air Cooled heated Probe, Stainless Steel
SBR-1000 Continuous High Flow (120 cfm), Weather Resistant Enclosure, w/ Pressure Sensor Digital Display, 5-ft of 1-1/2” Vacuum Hose, 120VAC.
SBR-93CFM Blower, APS, 93 CFM, 120V (for non-continuous sampling) Blower Assembly for APS Probes, SBR-10 frame, 93 cfm with 5ft of 1-1/2” Vacuum Hose, 120VAC, Variable Speed Controller
SBR-96CFM Blower, APS, 96 CFM, 120V
SBR-96CFM-V Blower, APS, 96 CFM, 240V
BLOWER ASSEMBLY FOR AIR COOLED PROBES
Part Number hG, Air Cooled heated Probe, Stainless Steel with Dual heaters
HGPA-8-HS 8 Foot, Air Cooled Mercury Probe
HGPA-9-HS 9 Foot, Air Cooled Mercury Probe
HGPA-12-HS 12 Foot, Air Cooled Mercury Probe
Part Number Description
TCA-765MG2C276 Type K Thermocouple Assembly with mini plug, C276 Alloy Sheath, magnesium oxide insulation, 1/8” diameter x 76.5”
TCA-112.5MG2C27 Type K Thermocouple Assembly with standard plug, C276 Alloy Sheath, magnesium oxide insulation, 1/8” diameter x 112.5”
REPLACEMENT STACK ThERMOCOUPLES
Add a “-V” to the part number for 240V/50Hz operation
Probe
Monorail
J- hook
Flange
Accepts MostSorbent Trap
Configurations
Method 30B
Appendix K
Appendix K RATA
Packing Gland
heatedSample Line
Call For additional information
Call For additional information
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 20a
Product Description
PF-4/40CLS 4” Stainless Steel Flange, 150 lb. Pattern, 2.670 Bored Diameter with Size 40 Cam and Groove Connector (for probes with tube outer sheath).
PF-6/40CLS 6” Stainless Steel Flange, 150 lb. Pattern, 2.670 Bored Diameter with Size 40 Cam and Groove Connector (for probes with tube outer sheath).
PF-40CL-UPGRADE
Flange Upgrade to the Cam-Lock Version
PF-4/6UCLS Flange Plate, Universal, 4”/6” Port with Size 40 Cam-Lock Connections.
PF-6PG38S 6” Pipe Flange, 150 lb. Pattern, Stainless Steel, with 2” Pipe Packing Gland (for use with probes with pitot option, pipe oversheath).
PF-4PG38S 4” Pipe Flange, 150 lb. Pattern, Stainless Steel, with 2” Pipe Packing Gland (for use with probes with pitot option, pipe outersheath).
PG-32/40CL 2” Oversheath Packing Gland, Steel Body, TFE Packing (for use with PF-40CLS flange) with Size 40 Cam and Groove Connector.
PF-4T32HC 4” Port Adapter, Carbon Steel w 4” Female Threaded. Half Coupling Used to Adapt Existing Stack Port w/Male Thread to Apex 4” Flange with Cam-Lock.
CG-CKIT-1 Cam and Groove Conversion Kit #1, for Use with Heated Sample Lines Under 2” O.D. (1 5/8 to 1 11/16”), Includes 2 Sets of Cam and Groove Fittings, Heat Shrink.
CG-CKIT-2 Cam and Groove Conversion Kit #2, for Use with Heated Sample Lines Under 2” O.D. (2 1/4 to 2 5/16”), Includes 2 Sets of Cam and Groove Fittings, PVC and Heat Shrink.
Product Description
10MMNU-S Nut, 10 mm Stainless Steel Tube
10M-F-TG TFE/GLS, 10 mm Glass-Filled Teflon Single Ferrule
10M-F-TG-DZ TFE/GLS, 10 mm Glass-Filled Teflon Single Ferrule, Dozen
HGP-STA Small Trap (6mm) Adapter for Mercury Probes. Includes 10MTUR6M-S (with 10mm Nut and ferrule) and Three 1/4” Ceramic Ferrules.
4NU-S Nut, 1/4 Tube, Stainless Steel
4F-C Ferrule, 1/4 Tube, Ceramic Teflon
REPLACEMENT PARTS
Umbilical Length
Replace -�- with Umbilical/Sample Line Length
Sample LineHGU-�HD
Sample Linew/Pitot HGU-�HDP
15 15’ Appendix K. Heated, dual Sample Lines (1/4”) Type K Thermocouples. Probe Power Cord. 120VAC.
25 25’ Appendix K. Heated, dual Sample Lines (1/4”) Type K Thermocouples. Probe Power Cord. 120VAC.
30 30’ Appendix K. Heated, dual Sample Lines (1/4”) Type K Thermocouples. Probe Power Cord. 120VAC.
50 50’ Appendix K. Heated, dual Sample Lines (1/4”) Type K Thermocouples. Probe Power Cord. 120VAC.
MERCURY PROBE ACCESSORIES Probe accessories are sold separately. Products can be custom made, so please call for any specific item.
FLANGES & PACKING GLANDS
Product Description
HGU-30UD 30 foot AppK Hg Umbilical Cable. Unheated Sample Lines (1/4”) for Paired Sampling, Stack & Trap Type K TCs. Probe Power Cord.
UNhEATED UMBILICAL/SAMPLE LINES
Product Description
HGU-25HD-R 25 foot Replaceable Sample Line
HGU-30HD-R 30 foot Replaceable Sample Line
hEATED UMBILICALS WITh REPLACEABLE SAMPLE
Additional length without pitot $40.00 per ft. Additional length with pitot $45.00 per ft
hEATED UMBILICAL/SAMPLE LINESThe umbilical/sample lines are available in various lengths and options: self-regulated heated and with or without pitot lines to meet the needs of customer applications.
Product Description
P1000-9 9’ with Chain, L-Bracket and Hardware, use w/ 4’ or 6’ probes
P1001-10 10’ Heavy Duty, Channel, with Chain, L-Bracket & Hardware, for use with lengths over 6’. Add $11 per LF
P2751 Swivel Frame Trolley with Eye-bolt,12” Chain and Quick Link
HGP-1SJ Mercury Probe Support “J” Hook attaches to standard Monorail
MONORAIL & hOOKS
CONSOLEDIF-N70 Inline Disposable, Nylon, Filter
Call For additional
information
21a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENTCOOLER (CONTINUED)
Product DescriptionAM-SP100A Fan, for Stirling Chiller, 115V, MechatronicsM-SD31 Temperature Controller, Red LED, Watlow.M-PSRS7512 Power Supply, 75W, 12V, 6 AMP, Input:
100-240VAC.M-PCB-REG-A Regulator PCB Assembly, 5V, for Use
with M-PSRS7512.M-CBR10A-M Magnetic Type Circuit Breaker Rocker Switch,
10 Amp. Horizontal Mount. Typically Used in 120V Consoles as Probe/Oven Breaker Switch. Panel Mount.
M-CB15A-M Magnetic Type Circuit Breaker, 15 Amp., Typi-cally Used in 120V Consoles as Main Breaker. Panel Mount.
SSR-330-25 Relay, SSRT, 25A 110/240V.SGC-J10-30B 10-Ft Jumper, For Use with Portable Hg
System, Gas Conditioner and Portable Hg Console.
SGC-110-30B 10-Ft Jumper for Use with Portable Gas Condi-tioner and Portable Model 30B Meter Console.
SGC-110-6K 10-Ft Jumper for Use with Portable Gas Conditioner and Portable Model XC-6000 Hg Meter Console.
SGC-J5 5-Ft Jumper, For Use in 18U Hg System. For Use with Rack Mount Gas Conditioner in 18U Cabinet.
PROBE REPLACEMENT PARTS
Product DescriptionTC-SP-KA Mini-Thermocouple Assembly, Type K, Male,
Cord Mount, includes Plug, Cover, Screws & Bushing.
HGH-2T144W Replacement Probe Heater, 2-ft, 575 Watt, (used on all probes, exit end of probe).
HGH-4T463W Replacement Probe Heater, 4-ft, 463 Watt.HGH-5T1650W Replacement Probe Heater, 5-ft, 1650 Watt.HGH-STRI72 Replacement Probe Heater 6-ft, 2000 Watt.HGH-9T838W Replacement Probe Heater, 9-ft, 775W.HGH-12T1000W Replacement Probe Heater, 12-ft, 1000W.MPT-6-133H Modular Pitot Tip (S-Type).9531K22 Cap Vinyl Protective, Used for Capping Sorbent
Traps During Pre- and Post-Leak Testing.10MMNU-S-EXT Particulate Shield for 10mm Sorbent Trap,
Stainless Steel Tube, 3/4” OD x 1.25” Lwith 10mm nut, Welded.
10MMNU-C-EXT Particulate Shield for 10mm Sorbent Trap, C276 Hastelloy C276 Tube, 3/4” OD x 1.25” L with 10mm nut, Welded.
10MMNU-S-EXTP Particulate Shield Plug, 10mm Stainless Steel Tube, 3/4” OD x 1.25” L with 10mm nut and plug, welded.
HGP-SHIELD-S-EXT-3 Stainless Steel Trap Shield, 3” Long x 2” Dia.HGP-SHIELD-S-EXT-6 Stainless Steel Trap Shield, 6” Long x 2” Dia.HGP-SHIELD–C-EXT-3 C276 Alloy Trap Shield. 3” Long x 2” Diameter.HGP-SHIELD–C-EXT-6 C276 Alloy Trap Shield. 6” Long x 2” Diameter.SR-2.625 U-Cord Neoprene Square Ring, 2” ID x 2 5/8”
OD x 3/16” TK, for CamLock Connectors.10M-F-TG-DZ Ferrule, 10mm, Glass filled Teflon, Dozen.10M-F-TG Ferrule, 10mm, Single, Glass filled Teflon10MMNU-S 10MM, Stainless Steel Tube Nut10MMBLP-S Plug, 10mm Tube Union, Stainless Steel
Product DescriptionQC-PMC2 QC, Stirling Gas Conditioner, Male,
Straight Connector, ¼” OD PTF, 1/8” OD X.170” ID (Used on Drierite Cartridge outlet/top) – Threaded Male.
QC-SGC-F4 QC, Stirling Gas Conditioner, Female,Coupling Body 1/4” OD (used on jumperfrom Stirling Cooler to sampling console) – Tube-Mount Female.
QC-SGC-M2 QC, Stirling Gas Conditioner, Straight Connector, Ferruless Polytube Fitting, PTF, 1/4” OD X .170” ID (Heated U-Cord Sample Line to Stirling, high-SO2 connec-tor) – Tube-Mount Male.
GA-GL-45S Seal for 1000ml Bottle.GSB-250SC Safety Coated Sample Bottle, 250mLGSB-500SC Safety Coated Sample Bottle, 500mLGSB-1000SC Sample Bottle, Clear Glass, GL-45
Threaded, 1000mL Safety Coated, for Con-densate Collection, Requires: GA-GL-45B cap and GA-GL-45S seal.
GSB-1000SCA
Sample Bottle Assembly, Clear Glass, GL-45 Threaded, 1000ml, Safety Coated, for Condensate Collection. Assembly includes GA-GL-45B cap and GA-GL-45S seal.
ALUMA-SORB
Activated Alumina Dessicant, Highly Ef-ficient Adsorbent with High Porosity and Contact Surface. 1/8” Diameter Beads, 2.5Kg (5.5 LB) Container with 80% Active Alumina (>/= 92%) and 20% Silica Gel.
COOLER CONSUMABLE
COOLER
Product DescriptionSGC-TR4/7-SCR Heat Exchange Assembly. Heat Exchange
Assembly, Silico Steel Coated, 4” Inner Tube, 7” Overall with Outer Tube.
26840 Aluma-Sorb Cartridge, Gas Drying Unit with 1/8” Stainless Steel FNPT Fittings. 2-5/8”x11-3/8”. 50g H2O Capacity. <.01psi@200lph press drop. 90psig working press. Polycarbonate.
26809 Mounting Clip for Aluma-Sorb Cartridge26840-A Aluma-Sorb Cartridge, Gas Drying Unit
with 1/4” Stainless Steel FNPT Elbow Barb Fittings. 2-5/8”x11-3/8”. 50g H2O Capacity. <.01psi@200lph Press Drop. 90psig Working Press. Polycarbonate. Includes Aluma Sorb.
TPFA-4-047W PFA, Tubing 5/32ID X 1/4OD X .047 Wall (jumper from U-cord to Stirling Cooler). minimum 10-ft recommended.
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 22a
VOST AND METhOD 6 TYPE SOURCE SAMPLER CONSOLEThe MC-623 Source Sampler Console (MC-623) is applicable for U.S. EPA Methods 6, 11, 26, VOST, and Methods 0030 and 0031. It can be used for any method requiring accurate volume measurement of low sample rates, typically 0.3 to 4 liters per minute. The console features a small lightweight dry gas meter fitted with an optical encoder and re-setable digital volume totalizer. The internal diaphragm pump is corrosion resistant and rated for up to 6 liters per minute free flow. The gas meter temperature, and up to five remote temperatures, are measured with Type-K thermocouples and displayed with a digital temperature display (LED). Three digital temperature controllers are standard for accurately maintaining probe and filter temperatures and auxiliary heater temperature (when appli-cable). The source sampler console is housed in a sturdy lightweight vented aluminum cabinet featuring all stainless steel hardware and three carrying handles. The console is easily serviced by simply unlatching the front panel latches and sliding out the chassis, allowing full access to all components. Standard with all stainless steel fittings and quick connects.
Add “V” to end of product number for 240 VAC/50 Hz option.
MC-623 VOST and Method 6 Type Source Sampler Console
Features• Metric Precision Gas Meter w/Optical Encoder (1.0ccm resolution, zero reset) • Digital Temperature display • Flowmeter • Automatic Temperature Controllers (probe, filter and auxiliary) • Elapsed Minute Timer• Includes Internal Pump• Stainless Steel 1/4” Sample Quick Connects & Fittings
. Specifications
Gas Meter: Positive displacement diaphragm, 45 lpm maximum and 0.33 lpm minimum recommended flow rate. 8 digit LCD display with push button reset for volumetric totalizer. Factory set 0-99999.999 liter totalizer resolution.
Flowmeters: Solid Machined Acrylic (100-1000 ccm), (0.2 - 2.4 Lpm), (4.0 Lpm).
Temperature Control: Compact, 1/32 DIN autotuning indicating temperature controller with external 25 amp solid state relays.
Temperature Display: 3.5 digit red LED display, -200°C to 1250°C range, 1°C resolution with external 6-channel selector switch. Minihelic Gauge (Pressure) 0 - 100 mm H2O. Vacuum Gauge 0-30 in Hg.
Sample Pump: Double-Diaphragm with12 VDC Motors, Max Vac. 20” Hg.
Power: 120 VAC/60 Hz Standard, 240 VAC/50 Hz Optional.
Umbilical Connections: Electrical: 4-Pin Circular Connector.
Sample Line: 1/4” Quick Connects.
Thermocouples: Type-K, Standard Size.
Dimensions: HxWxD: 14.5” x 16” x 10.5” (36.8 cm x 40.6 cm x 26.7 cm).
Weight: 28 lbs (12.7 Kg).
Sampler Consoles
Product Description
MC-623A 100 - 1000 ccm
MC-623A-V 100 - 1000 ccm
MC-623B 0.2 - 2.4 lpm
MC-623B-V 0.2 - 2.4 lpm
MC-623C 0.2 - 4.0 lpm
MC-623C-V 0.2 - 4.0 lpm
Model A, B , or CA:100-1000ccm B: 0.2-2.4 Lpm C: 0.2-4.0 Lpm
V: 240VAC~no charge
MC-623 Meter Console
23a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
XC-60 METER CONSOLEThe XC-60 Source Sampling Console is a small, lightweight and economical sampling unit designed for portability. At less than 22 pounds, the model is easy to take anywhere. The XC-60 comes with a sample pump, dry gas meter, rotameter, fine and coarse controls valves, and five Type-K thermocouple inputs. Several models available. Suitable for U.S. EPA Methods, NIOSH methods, mold testing, asbestos testing, and more.
XC-60 GAS SAMPLER
Features • Precision Gas Meter w/Optical Encoder (standard)• Durable UHMW Polyethylene Case with Built-In Handle• Digital Temperature Display• Needle Valve for Precise Flow Control• Stainless Steel Quick Connect• Digital Elapsed Timer• Up to Five External Temperature Inputs• Dual Scale Vacuum Gauge
XC-60 -
Version A, B , or CA:100-1000ccmB: 0.2-2.4 LpmC: 0.2-4.0 Lpm
V: 240VAC~no charge
XC-60 Meter Console
Specifications
Gas Meter: Model AP25, positive displacement diaphragm type 0.7 liters per revolution. Optical encoder sensor, Gas volume totalizer with an 8 digit LCD Display, Quadrature pulse output, 1 cc resolution (standard).Sample Pumps: hargrave BTC II Series Pump - Dual head miniature pump, brush motor, 12VDC. Max unrestricted flow 11 LPM, Maximum Vacuum Range 0-20 in. Hg.
KNF N815 Series - Mini diaphragm vacuum pump, eccentric. Ryton pump head, CR Diaphragm, EPDM Valves, 15 LPM Flow, Maximum Vacuum 26 in. Hg110V/60Hz.Probe Temperature Control: Compact, 1/32 DIN autotuning indicating temperature controller with external 25 amp solid state relay. 4-Pin Circular Connector, Standard Type-K Jack for TC input.
Temperature Display: 3.5 Digit LED display (-105°F to 1372°F), Type-K Display and controller are reset-table for OC upon request (OC is standard for export).Vacuum Gauge: Dual Scale, 0-30” Hg/0-100kPa.
Sample Inlet: 1/4” stainless steel quick-connect.
Power: 115 VAC/60 Hz ; 240 VAC/50 Hz (optional).
Dimensions: HxWxD: 21” x 9.5” x 14” x (53 cm x 24 cm x 35.5 cm).
Weight: 21.6 lbs (9.8 kg).
Applicable to U.S. EPA Methods:• Method 4A Moisture Determination.• Method 6 Sulfuric Acid Mist and SO2.
• Method 11 Hydrogen Sulfide in Petroleum Refinery Gas Streams.• Method 18 Integrated Bag Sampling for Organic Compounds.• Method 26 Hydrogen Halides And Halogens• VOST Methods (Volatile Organic Compounds).• Any Sampling Method Requiring Accurate Volume Measurement at low sample rates (0.3 - 4 lpm).
Model Description
XC-60A Meter Console w/ Optical Encoder and Temperature Controller with DGM-AP25, Rotameter 100-1000 CCM, 120 VAC/60 Hz. Hargrave BTC II Series Pump.
XC-60A-V Meter Console w/ Optical Encoder and Temperature Controller with DGM-AP25, Rotameter 100-1000 CCM, 240V/50 Hz. Hargrave BTC II Series Pump.
XC-60B Meter Console w/ Optical Encoder and Temperature Controller with DGM-AP25, Rotameter 0.2 - 2.4 LPM, 120 VAC/60 Hz. Hargrave BTC II Series Pump.
XC-60B-V Meter Console w/ Optical Encoder and Temperature Controller with DGM-AP25, Rotameter 0.2 - 2.4 LPM, 240V/50 Hz. Hargrave BTC II Series Pump.
XC-60C Meter Console w/ Optical Encoder and Temperature Controller with DGM-AP25, Rotameter 0.2 - 4 LPM, 120 VAC/60 Hz. KNF N815 Series.
XC-60C-V Meter Console w/ Optical Encoder and Temperature Controller with DGM-AP25, Rotameter 0.2 - 4 LPM, 240V/50Hz. KNF N815 Series.
Sampler Console
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 24a
MINIATURE PROBE ASSEMBLIES & LINERSMINIATURE PROBE
Miniature Probe Assembly
8
8
Miniature Liners
STAINLESS STEEL ADAPTERS
Stainless steel adapter, #12/5 socket to 1/4” tube fitting.MGA-12S4
Model DescriptionMGNS-12B Glass Adapter, 12/5 Ball to #15 Thread
Miniature Probe Accessories
Model DescriptionMPS-36H 36 inch Miniature Heated Probe
sheath, 3/4 inch OD Sheath, 120 VAC (Liner not included).
MPS-48H 48 inch Miniature Heated Probe Sheath, 3/4 inch OD Sheath, 120 VAC (Liner not Included).
MPS-60H 58 inch Miniature Heated Probe Sheath, 3/4 inch OD Sheath, 120 VAC (Liner not Included).
Miniature Probe Assemblies Miniature Probe LinersModel DescriptionMPL-36G1 36 inch, 8 mm (5/16”) OD,
Pyrex Liner with 12/5 Ball Joint
MPL-36G2 36 inch, 8 mm (5/16”) OD, Pyrex Liner with Glass Cup (No Ball Joint)
MPL-36G4 36 inch, 8 mm (5/16”) OD, Pyrex Liner, Plain Both Ends (No Ball Joint)
MPL-36G5 36 inch, 6 mm (1/4”) OD, Pyrex Liner, Plain Both Ends (No Ball Joint)
MPL-48G1 48 inch-8mm Pyrex Liner with 12/5 Ball Joint
MPL-48G2 48 inch Pyrex Liner (8mm) with Glass Cup (No Ball)
MPL-48G4 48 inch-8mm Pyrex Liner, Plain Both Ends
MPL-48G5 48 inch Pyrex Liner, 1/4 inch, (No Ball Joint)
MPL-60G1 60 inch-8mm Pyrex Liner with 12/5 Ball Joint
MPL-60G2 60 inch pyrex liner (8mm) with Glass Cup (No Ball Int)
MPL-60G4 60 inch-8mm Pyrex Liner, Plain Both Ends
MPL-60G5 60 inch-6mm Pyrex Liner, Plain Both Ends
Stainless Steel #12/5 socket elbow to 1/4” tube fitting.MGA-12SEL4
Glass filled PTFE Adapter, 12 mm socket to 5/16” tube fitting, MPL probe liner adapter.MGA-12S5TG
Glass filled PTFE Adapter, 12 mm ball to 5/16” ube fitting, MPL probe liner adapter.MGA-12B5TG
PTFE ADAPTERSStainless steel adapter, #12/5 Ball to 1/4” tube fitting.MGA-12B4
25a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
SK-606 Method 6
VSB4 with PC-3/4
VERSACASE
VersaCase4 Sample Case with hinged, removable doors. Does not include probe clamp.Inside cabinet Dimensions: HxWxD 9.5” x 12.5” x 6.75” (24.1 cm x 31.8 cm x 17.1 cm).
VSB4
VersaCase products are sturdy, reliable items for use in many U.S. EPA methods. Apex Instruments has an array of Versacase products available for any source testing need.
VSB2 VERSACASEThe VSB2 VersaCase is a lightweight portable lab frame ideal for supporting complex glassware setups. Originally designed to complement the Model 623 Source Sampler Console for Volatile Organic Sampling (VOST). Unit fea-tures a pre-punched panel with a combination handle/monorail bracket, coolant reservoir brackets (accommodates standard modular impinger cases), and removable front and rear doors. Interchangeable probe clamps for 3/4” and 1” sheaths are available. Call for details on customized kits for other testing methods.Dimensions: HxWxD: 24” x 12” x 11” (61 cm x 30.5 cm x 27.9 cm).
VSB2
Features• Lightweight: 5.5 lbs (2.5 kg)• Slotted Probe Clamp Mount for Different Height Glassware• Handle/Monorail• Hinged Removable Doors• Umbilical Support Bracket
VSB2(shown open with blank panel)
Model DescriptionPC-3/4 Stainless steel hinged probe
clamp (for 3/4” OD Probe)
PC-3/4E Extended stainless steel hinged probe clamp (accepts MFH-25CA)
MSB-1 Insulated midget impinger sample tray with drain valve
ICE-20 Small Ice Pack, blue gel
VSB Options
The VersaCase Umbilical Cable (VU-) includes four Type-K thermocouple extensions, 1/4” quick connects, sample line and three plug-in jacks terminating in a sturdy aluminum junction box. Standard with stainless steel fittings and quick connects. Other lengths available upon request.Add “V” to end of product number for240 VAC/50 Hz option.
30’ VersaCase Umbilical with Connection Box, 1/4” stainless steel quick connect.
VU-30
90’ VersaCase Umbilicalwith Connection Box,1/4” stainless steelquick connect.
VU-90
VERSACASE UMBILICAL
SUPERVOST SAMPLING KIT, SK0031Kit for VersaCase2 with 110 Volt Pump: VSB2, PC3/4, V31-CGS, VC31-SET, MPS-36H, MPL-36G2 (3x), VU-30, MM5-P, SB-3.
SK-0031
VSB2(exterior)
60’ VersaCase Umbilical with Connection Box, 1/4” stainless steel quick connect.
VU-60
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 26a
MIDGET GLASSWARE & ACCESSORIES (METhOD 6)Midget glass impingers feature unground double O-Ring 24/40 taper joint and 12/5 O-Ring ball joints. Bottle capacity is 40ml. The Insulated Sample Tray with Drain Valve (MSB-1) can hold a Midget Glassware Set (MGN-CGS) and two nontoxic Ice Packs (ICE-20). The ice packs allow quick turn around. At the end of the run simply remove the ice packs and drain the water before purging. Set includes impingers (plain and orifice), U-Tubes, Connectors and Clamps.
MSB-1 With Glassware Set(Method 6)
Midget Impinger AssemblyMidget Impinger Assembly with plain stem (#12/5 unground O-Ring ball joints).
mgn-1a
Midget Impinger AssemblyMidget Impinger Assembly with orifice stem (#12/5 unground O-Ring ball joints).
mgn-1aO
Midget U-TubeMidget U-tube with 12/5 unground socket joints.
mgn-2
Midget Knockout Impinger AssemblyMidget Knock-out Impinger Assembly (#12/5 unground O-Ring ball joints).
mgn-1aK
Midget Impinger InsertMidget Impinger Insert with plain stem (#12/5 unground O-Ring ball joints).
mgn-1i
Midget Impinger InsertMidget Impinger Insert with orifice stem (12/5 Unground O-Ring ball joints).
mgn-1iO
MIDGET GLASSWARE
Midget ConnectorL-Connector with 12/5 sockets.
mgn-6
Midget Impinger BottleMidget Impinger Bottle with unground taper joint.
mgn-1B
The Apex Instruments Method 6 and Method 26 Sampling Kits are normally used in conjunction with the XC-60 or Model 623 Source Sampler Console or alternative metering devices. The midget impingers
can be used for many methods, including NIOSh and OShA methods. The Method 6 Sampling Kit (SK-606) can be modified for U.S. EPA Method 26 with the addition of the SK-626 Kit.
Packing List
Packing List
MIDGET GLASSWARE SET (INCLUDES):• 4 Midget Impingers (3 MGN-1A, 1 MGN-1AO)• 3 Midget U-Tubes (MGN-2)• 1 L-Connectors with 12/5 Sockets (MGN-6)• 10 12/5 Ball Joint Pinch Clamps (BS12)
mgn-CgS
MGN-CGS Midget Glassware Set
Insulated Sample Tray with Drain Valve.mSB-1
Ice Packs.iCE-20
27a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
Glass 3-way Valve with #12/5 unground socket joints, inlet and outlet, ball joint purge. mgn-3SB
Glass 3-way Valve with #12/5 unground socket joints. mgn-3
Glass adapter, #12/5 unground socket to 1/4” tube.mgn-12S4
Glass Adapter, #12/5 socket to #18 thread.
mgnS-12S/18
Glass adapter, #12/5 unground O-Ring ball to 1/4” tube.mgn-12B4
Ungrounded glass adapter, #12/5 ball to #18 thread.mgnS-12B/18
Glass 3-way valve Glass Adapters
MIDGET GLASSWARE & ACCESSORIES (CONTINUED)
Impinger Outlet with thermocouple and tubing, #12/5 stainless steel socket. For use with midget glass impinger (MGN-1A).
mga-101
Impinger Outlet with thermocouple and 1/4” straight tube for use with PTFE Impingers (MGT-1)
mgS-101
Pinch Clamps
Ball Joint ClampStainless steel #12/5 ball joint clamp.
BS12
Keck ClipPlastic Keck Clip, Size 13, for #12/5 ball joints.
KBS-13
Ball Joint ClampStainless steel #12/5 ball joint clamp, Pyrex® with screw.
rC-13
MIDGET ACCESSORIES
Viton O-Ring for grooved #12/5 ball.
O-011V
Viton O-Ring for grooved #12/5 Ball, DOZEN.
O-011V-DZ
Impinger Outlets
O-Rings
MidgetPFA Impinger
Model DescriptionMGT-1 Midget PFA Impinger with Two 1/4” Tube Unions,
60 ml Volume
MGS-2T6 TFE U-Stem (1/4” OD)
MGS-3T6 TFE L-Stem (1/4” OD)
4SC4-PFA PFA Tube Union, 1/4”
PFA Impingers
Model DescriptionGA-GL-18B Bored Cap, GL #18
Threads
GA-GL-18S Silicone Seal Ring, 8 mm Hole Diameter
GA-18T6 PTFE Seal Ring, 6 mm Hole Diameter
GA-18T8 PTFE Seal Ring, 8 mm Hole Diameter
GL #18 Cap and Seals
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 28a
METhOD 6 (SO2)The Method 6 Source Sampling Kit for VersaCase4 (SK-606) features the miniature VersaCase. Method 6 measures sulfur dioxide (SO2) emissions from stationary sources. A gas sample is taken from the stack, and separated from the mist. The VersaCase can be used with the new XC-60 or the classic MC-623.
SK-606
SK-606-V
Kit Includes• Glass lined heated probe assembly • Midget glassware set • Sample tray • Nontoxic ice packs• VersaCase4• Probe Clamp• Outlet with thermocouple well• Connecting accessories• Adapters• Seals• Umbilical cable to connect to the XC-60 or Model 623 Source Sampler Console
Sampling Kit for Versa Case4 (SK-606)
Packing List
VU-30
29a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
SUPERVOST SAMPLING EQUIPMENTThe Apex Instruments SuperVOST Sampling Kit includes the multifunctional VersaCase2 cabinet with a redesigned mounting panel, glass-lined probe assembly, VOST glassware with clamps, insulated coolant reservoir with submersible pump and VU-cord. The VU-cord can be used for connection directly to the Model 623 Source Sampler Console, XC-60 Meter Console or to Models 572 and 563 with the VUA orifice flow adapter.
SuperVost Sampling Kit
Packing List
Packing List
TPFA-4/2
V31-CGS SuperVOST Glassware Set Includes:
1 VG-1/18 3-way Valve with TFE Valve Body, #18 Threads Inlet and Purge, 8mm Outlet
1 VG-2/18 VOST Charcoal Trap, #18 Threads & Glass Frit
2 VG-34/18 SuperVOST Coil Condenser, 2” Diameter, #18 Threads and Water Jacket Hose Barbs
1 VG-54/18 SuperVOST Water Trap, 40ml with #18 Threads, 45° Offset Exit
4 VG-6 VOST Absorption Cartridge, 1/4” Ends
1 4SC4-T PTFE Straight Union, 1/4”
2 GA-18T8 TFE Seal Ring, 8mm Hole Diameter
7 GA-18T6 TFE Seal Ring, 6mm Hole Diameter
10 GA-GL-18B Bored Cap, #18 Threads
1 GA-GL-18/9 Silicone Seal for 1/4” Tubing, 6mm Hole Diameter
1 TPFA-4-047W PFA Tubing, 1/4 inch, formed, (5 ft. total, 2 pieces)
3 TL-7/5 Surgical Tubing, 3/8”, 24” length
1 VG-125 Knock-out Flask, 125mL with #15 Threads
SuperVOST Glassware Set
Model DescriptionPC-3/4 Stainless steel hinged probe clamp
(for 3/4” OD Probes)
PC-3/4E Extended stainless steel hinged probe clamp (for 3/4” OD Probes)
Versacase Probe Clamps
Model DescriptionGA-GL-18B Bored Cap with Screw/Hole,
GL #18 Threads
GA-18C Solid Cap with Screw, GL #18 Threads with Seal
GA-GL-18/9 Silicone Seal Ring for 1/4” Tubing, 9.0 -11.00 mm Hole Diameter
GA-GL-18S Silicone Seal Ring, #18 Threads, 6.5 mm Hole Diameter
GA-18T6 TFE Seal Ring, 6 mm Hole Diameter
GA-18T8 TFE Seal Ring, #18/8 mm Hole Diameter
GL Caps and Seals for SuperVost
SK-0031 SuperVost Source Sampling Kit For VersaCase2 with 110Volt Pump: VSB2, PC3/4, V31-CGS, VC31-SET, MPS-36H, MPL-36G2 (3x), VU-30, MM5-P, SB-3.
SK-0031
SK-0031-V SuperVost Source Sampling Kit For Method 0031, with 240Volt Pump.
SK-0031-V
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 30a
The Method 26 Extension Kit for VersaCase (SK-626) is required for modification of the Method 6 Source Sampling Kit (SK-606) in order to perform Method 26.The sample is passed through a pre-purged heated probe and filter into dilute sulfuric acid then dilute sodium hydroxide solutions which collect all the gaseous hydrogen halides and halogens, respectively. The filter collects particulate matter including halide salts but is not routinely recovered and analyzed. The separate solutions are analyzed by ion chromatography.
SK-626
SK-626V
METhOD 26 (hYDROGEN hALIDES, hALOGENS)
3-Way Valve heaters
Kit Includes• Extended VersaCase Probe Clamp• Additional Impingers• Liners• Heated filter assembly• Filters, TFE Membranes• Adapter• Heater assembly• Three way Heated Assembly valve
SK-626 is for use in addition to SK-606 Method 6 Kit.
Model DescriptionMH-30 Replacement 30 W/120 VAC Heater for MVH-1
(add “V” for 240 VAC)
MGN-3SB Glass 3-way Valve with 12/5 Unground Socket Joints Inlet and Outlet, Ball Joint Purge
TFA-25B 25 mm TFE Filter Replacement Body Only with 1/4” Tube Union, No Clamp
MH-50 Firerod Heater Sub-Assembly with Power Cord and TC, 50 W, 120 VAC, for MFH-25 Filter Clamp
TF1165 TFE Membrane, 25 mm, 30-60 Micron, 10/pack
PC-3/4E Extended 3/4” Probe Clamp (accepts MFH-25CA)
MGN-12B4 Glass Ball Adapter, Unground 12/5 Ball to 1/4” Tube w/ O-Ring
MFH-25C Filter Clamp, Threaded, Aluminum, for 25mm Filter Assembly
Method 26 Accessories
heater 3-way Valve Heater Assembly, aluminum body with 30W heater and thermocouple. Shown here with valve.
mVH-1
mVH-1V
heated Filter Assembly w/ClampHeated Filter Assembly with clamp (MFH-25C), 25 mm filter body (TFA-25B) and heater (MH-50).
mFH-25Ca
mFH-25CaV
Sampling Kit forVersaCase (SK-626)
31a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
GAS SAMPLING BAG SAMPLING EQUIPMENT FOR VOC’SThe M180 VacBag Sampler System takes an integrated gas sample, in accordance with the U.S. EPA Method 18, by evacuating the stainless steel airtight container fitted with a gas sampling bag, preventing the gas sample from coming into contact with the sample pump. The TBE Enclosures come standard with clear Lexan® lid, a 1/4” valved female quick connect and a 1/4” male quick connect.
SK-m180 SK-m180-V
Bag Stainless Steel Enclosures4 Gallon stainless steel Bag Enclosure with 1/4” stainless steel quick connects. Accepts TB-18-P.
tBE-4g6 Gallon stainless steel Bag Enclosure with 1/4” stainless steel quick connects. Accepts TB-18 x 24-P.
tBE-6g 10 Gallon stainless steel Bag Enclosure, with 1/4” stainless steel quick connects. Accepts TB-18 x 36-P.
tBE-10g
Drum heaterFor heated gas bag sampling up to 150°C (300°F), Apex Instruments offers a thermostatically controlled flexible silicone rubber drum heater and thermal blanket. The heater is easily attached with quick acting spring latches and the quilted thermal blanket is attached with snap buttons.
Flexible Silicone Drum Heater 4-10 Gallon with Thermostat, 300 Watts/240 V Adj. 50 to 425°F, 220 VAC.
tBE-HEatEr-V
Insulated Blanket, fits the TBE-4G.tBE-4g-BKt
Insulated Blanket, fits the TBE-6G.tBE-6g-BKt
Insulated Blanket, fits the TBE-10G.tBE-10g-BKt
10 gallon (5 liter)
4 gallon(16 liter)
6 gallon(25 liter)
TBE-4G TBE-6G TBE-10G
Kit includes • 6 gallon airtight stainless steel enclosure• 3 Gas sampling bags• Sample pump• PFA tubing• Stainless steel unions and tubing• 1/4” Quick connects• 4 and 10 gallon enclosures also available
Caution: The heater temperature will rise rapidly since the drum is virtually empty. Start with the thermostat set at the lowest temperature setting. Do not use in hazardous locations.
heater temperatures should be closely monitored during initial use. Thermostat requires several cycles to break in. Calibrate the thermostat while installed before initial use.
Model DescriptionO-452N50 12” O-ring Seal, Nitrile for TBE-4G, 6G, and 10G
QC-M4-SS 1/4” Stainless Steel Male Quick Connect
QC-F4-SS 1/4” Stainless Steel Female Quick Connect
Accessories
Flexible Silicone Drum Heater 4-10 Gallon with Thermostat, 300 Watts/240 V Adj. 50 to 425°F, 110 VAC.
tBE-HEatEr
Tedlar® Gas Sampling Bags Are No Longer Available.
Please Call Apex For An Alternative Material.
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 32a
TEDLAR® GAS SAMPLING BAGSTedlar® Gas Sampling Bags are the first choice for collecting a variety of gaseous com-pounds. Tedlar® bags are referenced for many U.S. EPA Methods including 3,18 and 0040. Bags fabricated from Tedlar® film are inert to most gases, resist gas permeation and can be reused for most applications after proper cleaning. They are flexible and strong, and use of a rigid container ensures a longer life and convenience during transporting. Tedlar® bags are fabricated from transparent 2ml film or can be special ordered fabricated from opaque black Tedlar® for photosensitive compounds. Custom sizes available upon request.
SAMPLING PUMP MODULESThe compact Gas Sampling Pump incorporates a Hargraves Miniature Dual Head Pump with a maximum vacuum of 25” Hg and open flow of 6 to 11 lpm. The polyethylene terephthalate (PET) pump is constructed with a silicone valve and neoprene diaphragm. Pumps feature direct read rotameter, non-reversible male and female quick connects, stainless steel fittings and needle valve, a vacuum gauge, timer and folding handle. Add “V” to end of part num-ber for 240 VAC option. Dimensions: HxWxD 6” x 7” x 8.5” (15.2 cm x 17.8 cm x 21.6 cm); Weight: 8 lbs (3.5 kg). Power: 120 VAC/50-60 hz.
Optional Nickel Plated Brass Roberts Valve
Poly 2-in-1 Combination Valve with Septum Fitting
tBP-102 �Model Description
TBP-102A Gas Sampling Pump Unit (50-500 ccm)
TBP-102B Gas Sampling Pump Unit (100-1,000 ccm)
TBP-102C Gas Sampling Pump Unit (200-2,500 ccm)
TBP-102D Gas Sampling Pump Unit (500-5,000 ccm)
Sampling Pumps
Sample bags come standard fitted with the Poly 2-in-1 Combination Valve and Septum Fitting. Each standard bag has one fitting located near the top center or in the center of the bag. Custom placement available.
Model� (type)
Description - P (poly 2-in-1 combo valve)
- R (Brass Rob-erts Valve)
TB-6- � 6” x 6” (0.6 liter)
TB-7-� 7” x 7” (1.0 liter)
TB-9- � 9” x 9” (2.0 liter)
TB-10- � 10” x 10” (3.0 liter)
TB-12- � 12” x 12” (5.0 liter)
TB-12X15- � 12” x 15” (7.0 liter)
TB-12X17- � 12” x 17” (8.0 liter)
TB-12X18- � 12” x 18” (9.5 liter)
TB-12X19- � 12” x 19” (10.0 liter)
TB-12X21- � 12” x 21” (12.0 liter)
TB-18- � 18” x 18” (16.0 liter)
TB-18X24- � 18” x 24” (25.0 liter)
TB-24- � 24” x 24” (40.0 liter)
TB-24X30- � 24” x 30” (56.0 liter)
TB-30- � 30” x 30” (80.0 liter)
TB-30X36- � 30” x 36” (100.0 liter)
Also available in Black Tedlar® for additional Price.
Gas Sampling Bags
Tedlar® Gas Sampling Bags Are No Longer Available.Please Call Apex For An Alternative Material.
33a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
METhOD 0040 SAMPLING EQUIPMENTMethod 0040 is designed, using gas sampling bags, for sampling principal organic hazardous constitu-ents from combustion sources like hazardous waste incinerators. This non-isokinetic method uses a constant or proportional sampling rate dependent upon the extent and variability of the emission flow rate (Method 2). The Apex Instruments Method 0040 Kit (SK-0040) utilizes the VSB2 VersaCase cabi-net, glass lined probe assembly, glassware, coolant reservoir with submersible pump, bag enclosure and umbilical cord for connection to the XC-60 or Model 623 source sampler console.
Method 0040 Kit Includes• VersaCase 2• Probe clamp assembly• Probe Assembly w/ heater & liners • Tedlar® Bag Enclosure (6 gallon/25 liter) & Bags• Heated filter assembly • Glassware• Clamps• Three way valve• Cold Box• Submersible coolant pump• Umbilical cable
Packing List
Qty. Model Description
VG40-CGS Method 0040 Glassware Set
Set Includes:
3 VG-1/18 3-Way Valve with #18 Threads, Inlet and Purge, 8mm Outlet
1 VG-34/18 SuperVOST Coil Condenser, 2” diameter #18 Threads
1 VG-125/18 Knock-out Flask, 125 ml with #18 Threads
2 VG-2/18 Drying Tube, Charcoal Trap with Glass Grit, #18 Threads
13 GA-GL-18B Bored Cap, #18 Threads
2 GA-18T8 TFE Seal Ring, #18/8, 8mm Hole Diameter
10 GA-18T6 TFE Seal Ring, #18/6, 6 mm Hole Diameter
18 TPFA-4-047W TFE Tubing, 1/4” OD, 1/8” ID, per foot
2 TL-7/5 Surgical Tubing, 7/16” OD, 15/16” ID, per foot
1 GA-18C Solid Screw Cap, #18
1 4ET4-PFA Union Tee, 1/4” Tube PFA
Method 0040 Glassware
Sampling Kit forVersaCase (SK-0040)
SK-0040 SK-0040-V
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 34a
Sampling Kit for Method 7
METhOD 7 NITROGEN OXIDESSAMPLING EQUIPMENTApex Instruments offers two different options to sample for nitrogen oxide emissions. The Method 7 Source Sampling Kit is available for Methods 7, 7A and 7B. The system grabs and collects the sample in an evacuated 2 liter flask containing a dilute solution of sulfuric acid and hydrogen peroxide. Method 7 normally requires the collection of multiple samples at 15 minute intervals.
CK-7a9
CK-7a9-V (220V)
Link to M7C/7D
Kit includes• Clamps • Flasks • Sample frame caddy with probe clamp • Probe assembly • Liners• Valve assembly with squeeze bulb
• Adapters• Evacuation pump• Vacuum Gauge• Temperature controller• Thermometer• Transport case (not shown)
Packing List
E7-B162P (120 Volt)E7-B162P-V (240 Volt)
35a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
MERCURY SPARE AND REPLACEMENT PARTS
Model DescriptionM-PCB-DACV3A Populated Printed Circuit Board for Data Acquisition and Control (DAC) for XC-6000EPC, Dual PC-Based Hg ConsolePCB-TC/MUX Populated TC/Mux Board for Use in XC-6000EPC Mercury Console, 8 Type K TC Channels with External Signal
and Moisture Analyzer InputsPCB-LED-HG Board, LED DisplayEL-PCB-MODBUS-1 Board, TCP/IP Modbus InterfaceEL-CAT55FT Cable, Ethernet CAT 5.5 FT (blue)EL-SDCARD A-DATA Speedy 1GB Secure Digital (SD) Flash Card Model SDC-1G0EL-EBR-2310 D-Link Router, IEEE 802.3/3u, IEEE 802.11b/g Wireless-G Broadband Router, Used in Meter Consoles in Storm
Case Enclosure onlyEL-WBR-1310 D-Link Router, WBR-1310 Router - 54Mbps, 802.11g, 4-Port, Used in Meter Consoles in SKB, Environmental EnclosuresGP-C131-11 Pump, BTC Diaphragm Pump, Brushless Motor, 10,000 HR, Max Vacuum 20”HG, 12VDC, 3900 RPM, Max PSIG 24”GP-D737B-2201 Pump Diaphragm Hargrave Replacement Pump for XC-30B and XC-260 Meter ConsolesDGM-AP25-5701 Dry Gas Meter w 5701 Optical Encoder, Metric, Model AP25 with Bushings and FittingsDGM-AP25K Replacement Kit for DGM-AP25-5701 with Optical Encoder & Adapter Plate for Use in Replacing DGM-SK25-5701DGM-APADPT Adapter Plate Kit for DGM-AP25-5701DGMC-3A-LF Pre-test 3 Point Low-Flow (less than 1Lpm) Calibration for Apex Meter Console. 900, 600, 300 ccm TOT4-36X72 Quadrature Pulse Digital Totalizer 36 X 72 DINAK-6000 Deluxe Mercury Audit Kit for Appendix K/Method 30B System Includes: SK25 DGM with 15-pt Calibration, Quadrature
Totalizer, Vaccum Gauge, 4U Black Polyethylene Molded Case, Handheld Type K Thermocouple Simulator with Certificate, Hand-Held Digital Barometer, Digital Thermometer, Vacuum Bottle
QC-ADAPTER-1/4” 1/4” Quick Connect Mercury Audit Kit AdapterEL-670-OA938 AC Fan, 92mm ,115VAC, 50CFMMA4-20SIM Simulator,4-20mA, with Enclosure, Connector, Power Switch, & PotentiometerAWM-4360 Airflow Sensor, Signal Conditioning: Amplified; Flow/Pressure Range: + 6000 sccm (6.0 SLPM); Linear Range 1LPM; Port
Style: Manifold, (Flow Controller)XC-6K-PGMC Programming Cable for XC-6000EPC Automated Mercury Sorbent Trap Metering ConsoleM-AM2312 Valve, 3-Way, .055/.048 Orifice, 12V VSO-1SV Valve, Solenoid, Proportional. Model VSONC-3S11-IC-FO Manifold Mount with Wire Leads and 11.5VDCSP-PSE541-M5 Sensor, Pressure, 0-30” Hg, 1 NPN/PNP Open Collector Transistor Output, 30VDC, 125mA
BARO-A-4V Barometric Pressure Sensor, 600 to 1100 mbar, Temperature Compensated, Amplified OutputM-CBR10A-M Electrical Breaker, 10A, Panel Mount Magnetic Type Circuit Breaker Rocker Switch, 10 Amp. Horizontal Mount.
Typically Used in 120V Consoles as Probe/Oven Breaker SwitchM-CB15A-M Electrical Breaker, 15A, Panel Mount Magnetic Type Circuit Breaker, 15 Amp. Typically Used in 120V Consoles
as Main BreakerD-60A Power Supply, 5V@6A, 12V@4AEL-P1082-031 Connector, A TO B USB, Panel MountEL-TL5242W Memory Backup Lithium Batteries 3.6V 2.1Ah Battery PackPCB-BATTERY Battery Interface Board with Short-Term Capacitor Backup for Use with XC-6000 DAC BoardTC-PJK ThermoCouple Jack, Type K, Panel, Snap-InAM-T3107000 C16-1 Series Amphenol Circular Connector. High Grade Plastic for Harsh Environmental Conditions.
Panel Mount Straight Female Slots, 7 Slot (6 + Ground (First Mate/Last Break)AM-T3108 C16 Amphenol Circular Connector, 4 Pin (Cable Straight Male), Probe / Trap Heater Power Connection, Console SideAM-T3109 C16-1 Amphenol Circular Connector, 4 Socket (Cable Straight Female), Probe / Trap Heater Power Connection, Probe SideXC-6K-MANI Manifold Subassy, XC-6000EPC - Service Replacement Manifold Subassembly Includes Vacuum Sensor,
Mass-Flow Sensor, 2-Way Manifold Valve, Proportional Valve, Stainless Steel Hose Barb Fitting. AssemblyCalibration Data to be Provided with this Unit.
DIF-N70 Disposable In-Line Filter, Nylon Housing with 1/4” Tube Stubs, 95%+ Efficiency for 0.1 Micron
CONSOLE REPLACEMENT AND SPARE PARTS
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 36a
CONSOLE
M-PCB-DACV3A
EL-PCB-MODBUS-1
EL-WBR-1310
TOT4-36X72Quadrature Pulse Digital Totalizer36 X 72 DIN.
Populated Printed Circuit Board for Data Acquisition and Control (DAC) for XC-6000EPC, Dual PC-Based Hg Console.
PCB-LED-hGBoard, LED Display.Board, TCP/IP Modbus Interface.
EL-EBR-2310D-Link Router, IEEE 802.3/3u, 11b/g Wireless-G Broadband Router, Usedin Meter Consoles in Storm CaseEnclosure only.
D-Link Router, WBR-1310 Router - 54Mbps, 802.11g, 4-Port, Used in Meter Consoles in SKB, Environmental Enclosures.
DGM-AP25-5701
DGM-APADPTAdapter Plate Kit for DGM-AP25-5701.
Dry Gas Meter w 5701 Optical Encoder, Metric, Model AP25 with Bushings and Fittings.
$404.00
PCB-TC/MUX
EL-SDCARD
Populated TC/Mux Board for Use inXC-6000EPC Mercury Console, 8 Type K TC Channels with External Signal and Moisture Analyzer Inputs.
A-DATA Speedy 1GB Secure Digital (SD) Flash Card Model SDC-1G0.
GP-C131-11Pump, BTC Diaphragm Pump, Brushless Motor, 10,000 HR, Max Vacuum 20”HG, 12VDC, 3900 RPM, Max PSIG 24” for XC-6000EPC.
DIF-N70Disposable In-Line Filter, Nylon Housing with 1/4” tube stubs, 95%+ Efficiency for 0.1 Micron.
GP-D737B-2201Pump Diaphragm Hargrave Replacement Pump for XC-30B and XC-260 Meter Consoles.
Adapter Plate Sold Separately.
37a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
CONSOLE
AK-6000 Audit KitDeluxe Mercury Audit Kit for Appendix K/Method 30B System Includes: AP25 DGM with 15-pt Calibration, Quadrature Totalizer, Vacuum Gauge, 4U Black Poly-ethylene Molded Case, Handheld Type K Thermocouple Simulator with Certificate, Hand-Held Digital Barometer, Digital Thermometer, Vacuum Bottle.
XC-6K-PGMCProgramming Cable for XC-6000EPC Automated Mercury Sorbent Trap Metering Console.
Magnetic Type Circuit Breaker Rocker Switch,10 Amp. Horizontal Mount. Typically Used in 120V Consoles as Probe/Oven Breaker Switch.
EL-TL5242WMemory Backup Lithium Batteries 3.6V 2.1AhBattery Pack.
VSO-1SVValve, Solenoid,ProportionalModel VSONC-3S11-IC-FO Manifold Mount with Wire Leads and 11.5VDC.
EL-670-OA938AC Fan 92mm 115VAC 50CFM.
AWM-4360Airflow Sensor, Signal Conditioning: Amplified; Flow/Pressure Range: + 6000 sccm (6.0 SLPM); Linear Range 1LPM; Port Style: Manifold.
M-AM2312Valve, 3-WAY, .055/.048 Orifice, 12V.
Kit Includes: Secondary Reference MeterDGM-AP25SRD
Thermocouple SimulatorM5C-520
handheld Digital BarometerBAR-4198
36” Thermocouple Type KTCA-36HG
6” Thermocouple Y AdapterTCA-6YHG
handheld WaterproofThermometerDPT-168-NIST
Insulated Ice BathAK-6TH16
DGM-AP25SRD
M5C-520 BAR-4198
DPT-168-NIST
TCA-36hG
TCA-6YhGAK-6Th16
M-CBR10A-MM-CBR15A-M
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 38a
CONSOLE
26809 AM-SP100A M-SD31
Battery Interface Board with Short-Term Capacitor Backup.
Thermocouple Jack, Type K, Panel, Snap-In.
Mounting Clip for Aluma-Sorb Cartridge. Fan, for Stirling Chiller, 115V, Mechatronics. Temperature Controller, Red LED, Watlow.
BARO-A-4VBarometric Pressure Sensor, 600 to 1100 mbar, Temperature Compensated, Amplified Output.
EL-P1082-031Connector, A to B USB, Panel Mount.
SP-PSE541-M5Sensor, Pressure, 0-30” Hg, 1 NPN/PNP Open Collector Transistor Output, 30VDC, 125mA.
TC-PJKPCB-BATTERY
Ah-610-AHousing, Adsorption, Assembly with 1/4” Fittings and Filled with Aluma-Sorb.
COOLER
M-PSRS7512Power Supply, 75W, 12V, 6 AMP, Input: 100-240VAC.
D-60APower Supply 5V@6A, 12V@ 4A, Meanwell.
M-PCB-REG-ARegulator PCB Assembly 5V, for Use with M-PSRS7512.
COOLER COOLER
COOLERCOOLER COOLER
39a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
CONSOLE AND COOLER
AM-T3109C16-1 Amphenol Circular Connector, 4 Socket (Cable Straight Female), Probe / Trap Heater Power Connection, Probe Side.
AM-T3108C16 Amphenol Circular Connector, 4 Pin (Cable Straight Male), Probe / Trap Heater Power Connection, Console Side.
hGh-2T144WReplacement Probe Heater, 2-ft, 575 Watt. (used on all probes, exit end of probe).
PROBE
hGh-4T463WReplacement Probe Heater, 4-ft, 463 Watt.
hGh-5T1650WReplacement Probe Heater, 5-ft, 1650 Watt.
hGh-STRI72Replacement Probe Heater, 6-ft, 2000 Watt.
SSR-330-25Relay, SSRT, 25A 110/240V.
XC-6K-MANIManifold Subassy, XC-6000EPC - ServiceReplacement Manifold Subassembly IncludesVacuum Sensor, Mass-Flow Sensor, 2-WayManifold Valve, Proportional Valve, StainlessSteel Hose Barb Fittings.
hGh-9T838WReplacement Probe Heater, 9-ft, 838W.
hGh-12T1000WReplacement Probe Heater, 12-ft, 1000W.
AM-T3107000C16-1 Series Amphenol Circular Connector.High Grade Plastic for Harsh EnvironmentalConditions. Panel-Mount Straight Female Slots,7 Slot (6 + Ground (First Mate/Last Break).
hEATED UMBILICAL / SAMPLE LINE
PROBE PROBE
COOLER
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 40a
HGP-STASmall Trap (6mm) Adapter for Mercury Probes. Includes 10MTUR6M-S (with 10mm Nut and fer-rule) and Three 1/4” Ceramic Ferrules.
SGC-J10-30B10-Ft Jumper, For Use with Portable Hg System, Gas Conditioner and Portable Hg Console.
ALUMA-SORBActivated Alumina Dessicant, Highly Ef-ficient Adsorbent with High Porosity and Contact Surface. 1/8” Diameter Beads, 2.5Kg (5.5 LB) Container with 80% Active Alumina (>/= 92%) and 20% Silica Gel.
GA-GL-45SSeal for 1000 ml Bottle.
QC-PMC2QC, Stirling Gas Conditioner, Male, Straight Connector, 1/4” O.D. PTF,1/8” O.D. X.170” I.D. (Used on DrieriteCartridge Outlet/Top) – Threaded Male.
QC-SGC-M2QC, Stirling Gas Conditioner, Straight Con-nector, Ferruless Polytube Fitting, PTF, 1/4” O.D. X.170” I.D. (Heated U-Cord Sample Line to Stirling, High-SO2 Connector) – Tube-Mount Male.
QC-SGC-F4QC, Stirling Gas Conditioner, Female,Coupling Body 1/4” O.D. (Used on Stirling Cooler Sample in Connection).
PROBE
Thermocouple Plug Assembly, Mini,Type K, Male.
TC-SP-KA
SGC-J55-Ft Jumper, For Use in 18U Hg System. For Use with Rack Mount Gas Conditioner in 18U Cabinet.
SGC-J10-6K10-Ft Jumper for Use with Portable Gas Conditioner and Portable Model XC-6000 Hg Meter Console.
HGP-SHIELD-S-EXT-6HGP-SHIELD-C-EXT-6Mercury Sorbent Trap Shields HGP-SHIELD-S-EXT ShieldsStainless Steel Trap Shield Available in 3” or 6” Long x 2” O.D. Diameter. Recommended for short sampling runs, such as those required by Method 30B.
HGP-SHIELD-C-EXT ShieldsC276 Alloy Trap Shield Available in 3” or 6” Long x 2” O.D. Diameter. Recommended for corrosive environments and long continuous sampling runs (5 to 7 days).
HGU-10DJU-Cord Jumper, Hg, Unheated, Dual. 10-Ft Umbilical Cable Jumper (Chiller to Console). Un-heated Sample Lines (1/4”) for Paired Sampling.
HGU-10DJ-SCU-Cord Jumper, Hg, Unheated, Dual. 10 Ft Umbilical Cable Jumper (Chiller to Console). Un-heated Sample Lines (1/4”) for Paired Sampling.
HGU-10DJ-6U-Cord Jumper, Hg, Unheated, Dual. 10 Ft Umbilical Cable Jumper (Chiller to Console). Un-heated Sample Lines (1/4”) for Paired Sampling.
41a www.apexinst.com 800-882-3214 /919-557-7300
MERCURY & GAS SAMPLING EQUIPMENT
10M-F-TGFerrule, 10MM, Single, Glass Filled Teflon.
10 M-F-TG-DZ(Qty. 12)
PROBE
10MMNU-SNut, 10MM Tube, Stainless Steel.
10MMNU-S-EXTParticulate Shield for 10MM Sorbent Trap Stainless Steel Tube, 3/4” O.D. x 1.25” L with 10mm Nut, Welded.
10MMNU-C-EXTParticulate Shield for 10MM Sorbent Trap, C276 Hastelloy C276 Tube, 3/4” O.D. x 1.25” L with 10mm Nut, Welded.
4NU-SNut, 1/4 Tube, Stainless Steel.
SR-2.625Neoprene Square Ring, 2” I.D. x 2-5/8” O.D. x 3/16” T.K., for Cam-Lock Connectors.
GSB-500SC
SPARES / CONSUMABLE
Sample Bottle, Clear Glass, GL-45 Threaded, 500mL Safety Coated, for Condensate Collec-tion, Used in 16U Shock Mount Rack Chiller.
GSB-250SCBottle, Sample, Clear Glass, GL-45 Threaded, 250mL with Safety Coat Sample Bottle, 250mL, Used in SC-40 Con-densate Collection Ice Bath.
GSB-1000SCSample Bottle, Clear Glass,GL-45 Threaded,1000mL Safety Coated,for Condensate Collection.
GSB-1000SCASample Bottle, Assembled, Clear Glass,GL-45 Threaded,1000mL Safety Coated,for Condensate Collection.Assembly includes GA-GL-45B, GA-GL-45S.
MERCURY & GAS SAMPLING EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com 42a
Consoles, MercSampler™ XC-6000EPC ... 4a-5aConsoles, MercSampler™ Firmware.......... 6aConsoles, MercSampler™ Software .......... 6a-7aConsoles, MercSampler™ Laptops ............ 7aConsoles, MercSampler™Cabinet Configurations ............................... 8a-9aConsoles, XC-30B ...................................... 15a 16aConsoles, XC-260 / App. K / Method30B ... 17a-18aGas Conditioners ........................................ 10a-11aGlassware, Midget ...................................... 26aGlassware, Midget Accessories.................. 26a-27aGlassware, PFA Impingers ......................... 23aGlassware & Sorbent Cartridges ................ 11aMethod30B Source Sampling System ........ 15a-16aMethod 6 (SO2) .......................................... 28aMethod 7 Sampling Equipment .................. 34a
MercuryMethod 26................................................... 30aMethod 26 Accessories .............................. 30aMethod 18................................................... 31aMethod 0040 Sampling Equipment ............ 33a MercSampler™ Audit Kit ............................ 12aMercSampler™ Audit Kit Accessories ........ 12aMercury Replacement Parts ....................... 35a-41aMercury Sorbent Traps ............................... 13a-14aProbe Liners, Miniature .............................. 24aProbes, Probe Accessories ........................ 19a-21aSampling Pump Modules............................ 28aSupervost Sampling Equipment ................. 29aBag Sampling Equipment ........................... 32aGas Sampling Bags .................................... 32aVersacase ................................................... 25a
Manometers
www.apexinst.com
919-557-7300 or 800-882-3214Fax: 919-557-7110
Website: www.apexinst.comContact: [email protected]
Apex Instruments, Inc.204 Technology Park Lane
Fuquay-Varina, N.C. 27526, U.S.A.
Flow, Pressure andtemPerature Catalog
Probes
Inclinometers
Doug Bernhardt Customer Service
Please feel free to call our friendly sales staff today!
Vance JonesDomestic Sales,
Customer [email protected]
Janet NicholsSales Manager
John StauberInternational [email protected]
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
FLOW, PRESSURE & TEMPERATURE
MERCURY AND gAS SAMPLINg SYSTEMS & EQUIPMENT
gAS ANALYSIS EQUIPMENT
APPENDIX
INDEX
ACCESSORIES
ISOKINETIC SAMPLINg EQUIPMENT
Accu-Flow, 2-D System ..............................3b - 5b
Pitot Tubes, Modular Pitots Standard Pitot Tubes ..................................6b - 9b
Cam-Lock, FlangesPort Adapters & Packing Glands ..........10b, 11b
Orifice Flow Meters, Inclinometers .............12b, 13b
Transducers / Transmitters Handheld Digital Manometers ...............14b, 15b
Air Velocity Kits, Liquid Manometers Magnahelic Gauges, Anemometers ...........16b, 18b
Thermometers, Humidity, Dew-Point Meters .......................................19b, 20b
Rubber Bushings, Thermocouple Plugs and Jacks .........................................21b
Flow Pressure & Temperature Index ..........22b
Appendix ...................................................23b
Phone: 919-557-7300 or In the U.S. 800-882-3214Monday-Friday, 8:00 a.m. to 5:00 p.m. (Eastern Time)
Fax: Order at your convenience 24 hours a day, 7 days a week 919-557-7110
Website: www.apexinst.com
Please visit our website for additional product information, new product releases, updated materials, manuals, reference data and valuable links.
Flow, Pressure &teMPerature MeasureMent
Sampling Location - US EPA Method 1 is performed to locate an appropriate sampling location to complete a velocity or particulate traverse. The sampling locations must meet certain criteria to be valid such as, the duct diameter size and the sampling location relative to flow disturbance locations to ensure laminar, non-cyclonic, flow in the stack.
Velocity Measurement - US EPA Method 2 is performed to determine the average stack gas velocity from measurement of the gas density and average velocity head using Type “S” (Stausscheibe or reverse type) pitot tube. Apex Instruments manufactures and guarantees Type “S” pitot tubes in accordance with the Method 2 design specifications. However, calibration is not standard with purchase of pitot tubes. Apex Instruments offers calibration equipment and services. A variety of materials, sizes and configurations are available. The most common are constructed from either 1/4 inch or 3/8 inch OD Stainless Steel or Alloy 600 tubing.
The Type “S” Pitot tube is constructed from two formed tubes with each leg or port on the same plane but facing opposing directions. The theory is based on when the pitot is faced into the gas stream flow the pressure difference between the two ports equates to the velocity pressure, DP. This differential velocity pressure is measured with devices, such as liquid manometers or electronic pressure transducers.
Type “S” Pitot Tube Design Advantages:
• Large sensing openings resist plugging in particulate-laden and saturated gas streams• Compact design fits easily in sampling ports• Maintains calibration in harsh environments• High differential pressure readings are beneficial in low velocity gas streams• Suitable for determining cyclonic flow and measuring yaw angle of the velocity vector• Economically priced
3b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENTFLOW, PRESSURE AND TEMPERATURE MEASUREMENT
Prototype Units Available for Trial Basis
Call Toll Free: 1.800.882.3214Email: [email protected]
NEW Product in DevelopmentAccu-Flow 2-d MEASuREMENT SYSTEMThe Apex Accu-Flow Measurement System is used for performing EPA Method 2G. The system uses a two-dimensional 3-hole prism-shaped pitot for accurately measuring flow rates for angular non-axial flow. This system provides a way for testers to improve the measurement of volumetric flow rate under cyclonic flow conditions found in some stacks and ducts. Multiple probes reduce the time for the flow Audits, therefore saving money by not operating at undesirable loads. Oversized sensor ports reduce plugging. The 1/4” pressure lines have quicker response and are less likely to leak than standard 1/8” lines.
Save Time and Money...Use up to 8 Probes Simultaneously
Key Advantage for the Source:1.) Save money reporting lower emissions.2.) With multiple probes, the time for Audits can be drastically reduced, thereby saving more money by not operating at undesirable loads.
Key Advantage for the Tester:1.) Easy to use, rotate-to-null and record the yaw angle and P2.) Variant of Method 23.) Simple calibration, similar to S-Type4.) Automated calculations and data records5.) Use 1 to 8 probes, simultaneously6.) Easy-to-use intuitive software for your laptop7.) Decrease test time and minimize errors
Apex 2D Accu-Flow will save time and money as well as provide more accurate certifiable results.
Key Features:Since all of the sensors are mounted on the probe, accurate, stable readings can be obtained immediately. The larger ports reduce potential plugging. 1/4” pressure lines provide quicker response and are less likely to leak than standard 1/8” lines.(continued on next page).
2-d Pitot ExtensionSize: 8’, 2” o.d.
(32PTX-8)
4”/ 6” Flange Adapterwith 12” extension
(PF46XT32S)
Accu-FlowSoftware
2-d Pitot (2dPT2)
2G u-cord(2G-uc-o)
Pod Interface Module
(2G-PM-o)
Probe Interface Module
(2G-Pod)
4b 800-882-3214 /919-557-7300 www.apexinst.com
Flow, PRESSuRE ANd TEMPERATuRE MEASuREMENT
Probe Interface Module / 2g-pod
Easy-To-use, Intuitive SoftwareThe operation software, hosted on a portable laptop computer, will allow the user to perform Method 2G (2-D) testing. software includes:• Number of probes used• Number of ports• Total number of traverse points to be sampled• Record differential pressure, flow yaw angle, stack temperature, static pressure and barometric pressure.
Accu-Flow Software(Included in 2G-Pod)
Product Description
2DPT2 2-D Pitot, 2 hole prism-shaped tip with 1’ sheath supplied with Type K thermocouple, 1/4” tube unions, 34” Long.
PT-CAL-2D Method 2G, 2-D pitot calibration (wind tunnel), 60 and 90 fps, yaw angle offsets determination.
32PTX-6 2-D Pitot Extension, 6’, 2” diameter sheath, split collar clamp with 1” ID.
32PTX-8 2-D Pitot Extension, 8’, 2” diameter sheath, split collar clamp with 1” ID.
2G-UC-30 30’ 2G cable with 7 pin, circular connectors.
2G-UC-60 60’ 2G cable 7 pin, circular connectors.
2G-UC-90 90’ 2G cable 7 pin, circular connectors.
2G-POD Method 2G POD Contains 2 x 5” Pressure Transducers,1 x 10” Pressure Transducer, 1 Digital Inclinometer, Type K TC Transmitter, Barometric Pressure Sensor plus Umbilical Connector, 2” Tube Clamp, 5 Barb Connectors, 1 TC Jack. Also includes AccuFlow Software, Connects to laptop via USB, 2G-POD power and transmits data over current-loop connection.
2G-PM1 2G Single POD Interface Module contains USB HUB and current-loop transmitter for connecting 2G-POD to a single laptop.
2G-PM4 2G MULTI (4) POD Interface Module contains USB HUB and current-loop transmitters for connecting up to 4 2G-PODs to a single laptop.
2G-PM8 2G MULTI (8) POD Interface Module contains USB HUB and current-loop transmitters for connecting up to 8 2G-PODs to a single laptop.
2-d Flow ModulAR SYSTEM coMPoNENTS
2-d PIToT (2dPT2)
2-d PitotThe new Apex Instruments 2DPT2 Pitot is capable of measuring the yaw velocity angle of nonuniform disturbed air flows. The yaw angle is determined directly by rotating the pitot to null the pressure across a pair of symmetrically placed ports on the pitot head. The yaw angle is measured with a re-mote inclinometer attached to the probe extension and digitally recorded. The average gas volumetric flow rate in the stack or duct is then determined from the average near axial velocity. 2-D Pitot, 2-Hole Prism Shaped with 1” Sheath Supplied with 1/4” tube connections.
2dpT2
dHM28-10
Handheld digital Manometer• Ideal for Auditing Pressure Sensors• Traceable Cert.
• 0-10” H2O• Resolution 0.001”
dHM28-10
Pendulum Style InclinometerEasy-to-use, hand-held Pendulum Style Inclinometer. 1/10deg accuracy: Includes plastic case.. The dial is 2.6”dia. with vernier divisions of 1/10deg. Height is 3.6”, width is 3.1”, wt :3.6oz.
INC-A300
Inclinometer
ProbeInterface Module
2-d calibrationApex Instruments 2-D Pitot Tube must always be cali-brated before initial use. Recalibration is also required either within 12 months of its first field use or after 10 field tests, whichever occurs later. Additionally the 2D pitot shall be is recalibrated before it is used again. Method 2G, 2-D Pitot Calibration (Wind Tunnel), 60 and 90 fps, yaw angle offset determination.
pT-CAL-2d
Pod Interface Module
2g-pM12g-pM42g-pM8
Pod Interface Module
Method 2G POD Contains 2 x 5” Pressure Transducers,1 x 10” Pressure Trans-ducer, 1 Digital Inclinometer, Type K TC Transmitter, Barometric Pressure Sensor plus Umbilical Connector, 2” Tube Clamp, 5 Barb Connectors, 1 TC Jack.
5b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
3-d Flow MEASuREMENT SYSTEMThe Apex Instruments MC-3D52 3-D Flow Measurement Console is used in conjunction with the 3-D Pitot to determine velocity pressure, and the yaw and pitch angles of the flow velocity vector in a stack or duct according to U.S. EPA Method 2F (the determination of stack gas velocity and volumetric flow rate with three-dimensional probes). This console features stable and reliable differential pressure transducers for the most demanding of stack testing conditions. A convenient blowback pump, quick connects, temperature display and all voltage outputs are available for easy connection to your data acquisition system.
SK-3d52...$8,055.00
classic Model Mc-3d52
Meter Console Specifications (MC-3D52):Stack Temperature: Type-K Thermocouple.Velocity Pressure: (P1-P2) Range 2.5” H2O.Yaw Null: Bidirectional (P2-P3) Range 2.5” H2O 2.5 Bi.Pitch Range: Bidirectional (P4-P5) Range ±2.5” H2O 2.5 Bi.Yaw Angle Range: Quadrature Pulse Output, 180° (static >360°).output connector: 9 pin D-Sub connector (all outputs are voltage based).Probe Sensor Inclinometer and Digital Indicator.
Product DescriptionMC-3D52 Digital 3-D Flow Measurement Console Digital Displays for temperature, velocity pressure, pitch pressure, yaw angle.3DPT2 3-D Pitot, 5 hole prism-shaped tip with 2’ sheath supplied with five 1/8” to 1/4” tube unions.PT-CAL-3D 3-D Pitot Calibration (Wind Tunnel), 60 and 90 fps, pitch from -30 to 30° degrees32PTX-4 3-D Pitot Extension, 4’, 2” Diameter Sheath, Split Collar Clamp with 1” ID.32PTX-5 3-D Pitot Extension, 5’, 2” Diameter Sheath, Split Collar Clamp with 1” ID.32PTX-6 3-D Pitot Extension, 6’, 2” Diameter Sheath, split collar clamp with 1” ID.32PTX-8 3-D Pitot Extension, 8’, 2” Diameter Sheath, split collar clamp with 1” ID.3DCALC1.0 3DCalc Method 2F Data Reduction Spreadsheet (MS Excel Workbook), with calibration DDL file and Excel Macro Link.U-3D-60 U-Cord 60 ft includes 5 pressure lines with 1/4” stainless steel quick connects, signal cable for inclinometer, 1 type K thermal couple extension.INC-S6-50 Inclinometer, S6 sensor, 360 degrees with 2” probe clamp, quadrature pulse output.
3-d Flow ModulAR SYSTEM coMPoNENTS
3dPT45 HolE PIToT wITH 4
FT. SHEATH PF-346XT32SuNIVERSAl PoRT FlANGE
w/EXTENSIoN
32M/32F-BBRASS BuSHING
(BoREd)
INc-AT2-50INclINoMETERATTAcHMENT
*PRoBE EXTENSIoN ASSEMBlY
MAGNEHElIc +/-.5” GAuGE
ANd BRAcKET
cloSE-uP dPT45 HolE PIToT
Magnehelic Gauge:Magnehelic Gauge, +-.5 INWC Differential.MAG-2301...$100.00
Magnehelic Bracket:Magnehelic Mounting Bracket.MAG-2d-BK...$40.00
optional Accessories:
6b 800-882-3214 /919-557-7300 www.apexinst.com
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
Type-S Pitot Tubes are used to measure the gas velocities. When the pitot is faced into the gas stream, flow and the pressure difference between the two ports equates to the velocity pressure. This differential velocity pressure is measured with liquid manometers or electronic pressure transducers.Baseline coefficient value is 0.84. Wind tunnelcalibration services are available upon request.
PITOT TUBES
Type-S Pitot Tube Design Advantages:• Large openings resist plugging in particulate laden and saturated gas streams.• Compact design fits easily in sampling ports.• Maintains calibration in harsh environments.• High differential pressure readings are beneficial in low velocity gas streams.• Suitable for determining cyclonic flow and measuring yaw-angle of the velocity vector.• Economically priced.
Other Lengths Available
U.S. EPA Method 1 specifies appropriate sampling locations for conducting a velocity or particulate traverse. The sampling locations must meet certain criteria to be valid. (ie., duct diameter and the sam-pling location, relative to flow disturbance locations to ensure laminar, non-cyclonic, flow in the stack.)Apex Instruments manufactures Type-S pitot tubes in accordance with the Method 2 design specifications. A wide variety of materials, sizes and configurations are available. The most common are constructed from either 1/4” or 3/8” OD stainless steel or Alloy 600 tubing.
-� OptionsTF Stack Thermocouple 2” Back Flush
TO Stack Thermocouple with 3/4” Offset
16 1” Oversheath
M Pitots with Modular Pitot Tip, 1/4” Tubing
MS Pitots with Staggered Pitot Tips
MO Modular Pitot Tip with Offset
Pitot Assembly Options
7b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
Call for Additional Information and / or Pricing on C276 Alloy 600. Stainless Steel
Type-S Pitots are Rated upto 1200OF and C276 and Alloy 600
Type-S Pitots are Rated up to 1800OF.
MOST POPULAR SIzESstainless steel type-s Pitot tube
Constructed from 1/4” Stainless Steel
Product Base TF TFR 16 TF16 TFR16
4PT-3
4PT-4
4PT-5
4PT-6
4PT-7
4PT-8
4PT-9
4PT-10
4PT-11
4PT-12
stainless steel type-s Pitot tube
Constructed from 3/8” Stainless Steel
Product Base TF TFR 16 TF16 TFR16
6PT-3
6PT-4
6PT-5
6PT-6
6PT-7
6PT-8
6PT-9
6PT-10
6PT-11
6PT-12
stainless steel type-s Pitot tubeConstructed from 1/4” Stainless Steel Tubing (Pitot Lines), w/ Modular Pitot Tip (3/8” diameter Stainless Steel Tubing)2” Oversheath
Product 32M TF32M TFR32M
6PT-3
6PT-4
6PT-5
6PT-6
6PT-7
6PT-8
6PT-9
6PT-10
6PT-11
6PT-12
Product DescriptionPG-24T 1 1/2” Oversheath Packing Gland, Steel Body, 1 1/2” MNPT, TFE
Packing
PG-32S 2” Oversheath Packing Gland, Stainless Steel Body, 2” MNPT, PTFE Ferrule Included
12MTC12-B 3/4” Packing Gland for Pitot with 3/4” Oversheath, Includes Nylon and Brass Ferrules, Brass
12MTC12-S 3/4” Packing Gland for Pitot with 3/4” Oversheath,Includes Nylon and Ferrules, Stainless Steel
16MTC16-B 1” Packing Gland for Pitot with 1” Oversheath, Includes Nylon and Brass Ferrules, Brass
16MTC16N-S 1 inch Packing Gland, for Pitot with 1 inch Oversheath, Includes Stain-less Steel Ferrule
16MTC16N-SF 1 inch Packing Gland, for Pitot with 1 inch Oversheath, Includes Nylon and Stainless Steel Ferrule 16F-N, 16MTC16-S
12F-GR 3/4” Graphite Ferrule, Alternative Packing for 16MTC16
16F-GR 1” Graphite Ferrule, Alternative Packing for 16MTC16
PACKINg gLANDS
Packing glands
Cam-Lock Packing glands
Packing glands
Link to Flanges
Call foradditional Information
Call foradditional Information
Call foradditional Information
8b 800-882-3214 /919-557-7300 www.apexinst.com
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
PITOT TUBE EXTENSIONS TELESCOPIC TYPE “S” PITOTApex Instruments Telescoping Pitot Probe allows the versatility of traversing larger stacks with optional telescoping ranges whileproviding the ability to package this probe in a compact container. The design incorporates a pitot tube with 1” OD oversheathconnected to a 2” OD extension (32PTX- ) with adjustable clamp. Rigid or flexible tubing connections are available. 3/8” ID PFAwith stainless steel overbraid is recommended. PFA or glass insulated Type-K thermocouples with overbraid are available.Varying pitot tube lengths are available. Please call for details.
length in mm
Product DescriptionMPT-6-133 Replacement Type-S Modular Pitot Tip for Oversheath Probes,
33mmL
MPT-6-181 Replacement Tip for Standard Method 5 Pitot, 181 mmL
MPT-6-218 Extended Pitot Tip for SFA-47, 218 mmL
MPT-6-252 Extended Pitot Tip for PM10 and SFA-47, 252mmL
MPT-6-320 Extended Pitot Tip for SFA-190, SFA-300 and SFA-2590, 320mmL
MPT-6-421 Extended Pitot Tip for PM10-2.5 and SFA-47, 421mmL
STAINLESS STEEL MODULAR PITOT TIP
Product Description
PTB-3 Modular Pitot Body, (without tip) 3/8” Tube, Pistol Grip, 3’ Length
PTE-2 2’ Modular Pitot Extension, 3/8” Tube
PTE-3 3’ Modular Pitot Extension, 3/8” Tube
PTE-4 4’ Modular Pitot Extension, 3/8” Tube
MODULAR PITOT COMPONENTS
MODULAR PITOTSThe unique design of the Apex Modular Pitot Tip reduces the collection of water droplets in the pitot lines. The lower tube is self-draining while the offset in the upper tube acts as water trap. The water can be easily cleared by tilting the tip or by back purging.
Product Description4SC4-S Stainless Steel Tube Union, 1/4”
4TUR6-S Stainless Steel tube end reducer; 3/8” tube union to 1/4” tube stub
6RU4-S Stainless Steel reducing tube union; 3/8” to 1/4”
6SC6-S Stainless Steel tube union, 3/8”
QC-M4-SS 1/4” Quick Connects
QC-M6-SS 3/8” Quick Connects
STAINLESS STEEL UNIONS AND QUICK CONNECTS
Order unions and quick connects separately
9b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
STANDARD PITOT TUBE FOR METHOD 2CThis Pitot tube is custom made to specifications outlined in US EPA Method 2C. Modified hemispherical-nosed pitot of Method 2C features a shortened stem and enlarged impact and static pressure holes. This pitot is useful for saturated gas streams when “back-purging” is ineffective. Pitot coefficient: 0.99 unless calibrated.
Product Description
PT2C-24 24” Standard Pitot, Stainless Steel, Method 2C
PT2C-36 36” Standard Pitot, Stainless Steel, Method 2C
PT2C-48 48” Standard Pitot, Stainless Steel, Method 2C
PT2C-60 60” Standard Pitot, Stainless Steel, Method 2C
STAINLESS STEEL PITOT
3-D PITOT CALIBRATION (PT-CAL-3D)All 3-D pitot tunes must be calibrated before use. Re-calibration is also required either within 12 months of its first field use after its most recent calibration or after 10 field tested, whichever occurs later. In addition, whenever there is visible damage to the 3-D head, the pitot shall be re-calibrated before it is used again.
5 Hole Prism Shaped with 4
foot Sheath
2-DIMENSIONAL PROBE (3-HOLE PITOT)The Apex Instruments 2-Dimensional Probe is used in Method 2G for measuring the velocity pressure and the yaw angle of the flow velocity vector in a stack or duct using measurements and a determination of the stack gas density, the average near-axial velocity of the stack gas is calculated. The rear-axial velocity of the stack gas accounts for the yaw, but not the pitch component of flow. The average gas volumetric flow rate in the stack or duct is then determined from the average near-axial velocity. The Inclinometer is used for determination of the calibrated yaw offset. The pitot is designed to be insert-ed into our 2 inch diameter probe extension. The pitot tube must be calibrated in accordance with Method 2G prior to use. (2-D Calibration....see page 4).
Pt-Cal-3d
3-D MODULAR FLOW SYSTEM
System Includes: Digital 3-D Flow Measurement Console, 3-D Pitot, 5 Hole Prism Shaped with 4 ft., Sheath, 3-D Pitot Extension, 2” Diameter Sheath, 1/4” TFE Lines - 10 ft., Universal Probe Extension Flange Fits 3”,4”, & 6” Ports, 2” Bored Brass Bushing, 2” MNPT with 2.035 Bore, 3-D Pitot Calibration (Wind Tunnel), Remote Inclinometer Sensor, 60 ft., 3-D U-Cord.
3-D PITOT (5-HOLE PITOT)The Apex Instruments 3-D Pitot is capable of measuring yaw and pitch of nonuniform flows. The yaw angle is determined directly by rotating the pitot to null the pressure across a pair of symmetrically placed ports on the pitot head. The yaw angle is measured with a remote inclinometers attached to the probe extension and digitally displayed on the console.The pitch angle is calculated using probe specific calibration curves. The average gas volumetric flow rate in thestack or duct is then determined from the average axial velocity.
2-D MODULAR FLOW SYSTEMProduct Description
2DPT2 2-D Pitot, 2 hole prism-shaped tip with 1’ sheath supplied with Type K thermocouples, 1/4” tube unions, 34” Long. PT-CAL-2D Method 2G, 2-D pitot calibration (wind tunnel), 60 and 90 fps, yaw angle offsets determination. 32PTX-6 2-D 2-D Pitot Extension, 6’, 2” diameter sheath, split collar clamp with 1” ID. 32PTX-8 2-D Pitot Extension, 8’, 2” diameter sheath, split collar clamp with 1” ID. 2G-UC-25 25’ 2G cable with 7 pin, circular connectors. 2G-UC-50 50’ 2G cable 7 pin, circular connectors. 2G-UC-100 100’ 2G cable 7 pin, circular connectors. 2G-MPDI Method 2G probe interface module, contains 2 x 5” pressure transducers, 1 x 10” pressure transducer, 1 digital Inclinometer, type-K thermocouple transmitter, barometric pressure sensor plus umbilical connector, 2” tube clamp, 5 barb connectors, 1 Thermocouple Jack also includes interface module, connects to laptop via USB, powers 2G-POD and Transmits data over current-loop connection. (2G-POD multi-pod interface module contains USB Hub and 4 current loop transmitters for connecting up to four 2G-PODs to a single laptop.)2G-SW Accu-Flow Software, included with 2G-POD. Includes worksheets for Methods 1-4 and assists user in collecting data points for Methods 2F / 2G / 2H. 2DCALC1.0 2DCalc Method 2F data reduction spreadsheet (MS Excel Workbook), with calibration DDL file and Excel Macro Link.
Product Description
SK-3D52 Method 2F Digital 3-D Flow Measurement System. CALL FOR DETAILS
10b 800-882-3214 /919-557-7300 www.apexinst.com
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
Product DescriptionPF-346T32S 2” FnPT, Universal Pipe Flange Reducer, Fits 3”, 4”, 6” Ports, SSPF-346XT32S 2” FnPT, Universal Pipe Flange Reducer with 12” Extension, Reversible, Fits
3”, 4”, 6” PortsPF-346T32S 2” FnPT, Universal Pipe Flange Reducer, Fits 3”, 4”, 6” Pipe Flanges, Stain-
less SteelPF-4/6U32-S Universal Pipe Flange with 2” FnPT, Fits 4” and 6” PortsPF-4/6UB-S Universal Pipe Flange, 4”/ 6” Port, 2.675 Bored Center, SSPF-4/6UCLS Universal Flange, 4”/ 6” w/ 2-1/2” Cam-Lock
UNIVERSAL PIPE FLANgE & FLANgE REDUCERS
CAM-LOCK, FLANgES, PORT ADAPTERS & PACKINg gLANDS
Flange & Cam-Locks
Threaded Pipe Flanges
REDUCING FLANGES
Product DescriptionPF-3/40CLS 3” Bored Pipe Flange, 150 lb pattern, 2.670 Bored
Diameter, with size 40Cam-lock Connector, Stainless Steel
PF-3CS 3” Pipe Flange, 150 lb FF Pattern, Bored with Threaded Coupling, Stainless Steel
PF-4BS 4” Bored Pipe Flange, 2.67” RF, 150 lb Pattern, Stainless Steel
PF-6BS 6” Bored Pipe Flange, 150 lb Pattern, 2.670 Bored Diameter, Stainless Steel
PF-4CLS 4” Bored Pipe Flange, 2.67” RF, 150 lb Pattern, Stainless Steel
PF-4CS 4” Bored Pipe Flange, 150 lb FF Pattern with Threaded Coupling, Stainless Steel
PF-4/40CLS 4” Bored Pipe Flange, 150 lb pattern, 2.67 Bored Diameter Welded Cam and Groove Connector (For Probes without Pitot Option, with Tube Outer Sheath) with size 40 Cam-Lock Connections, Stainless Steel
PF-6/40CLS 6” Bored Pipe Flange, 150 lb pattern, 2.67 Bored Diameter welded Cam and Groove Connector (For Probes without Pitot Option, with Tube Outer Sheath) with size 40 Cam-Lock Connections, Stainless Steel
PF-6/48CLS 6” Bored Pipe Flange, 150 lb Pattern, Bored Inside Diameter, with size 48 Cam-lock Connector (For Use with Pitot Version Mercury Probe with Pipe Oversheath),Stainless Steel
PF-6CLS 6” Bored Pipe Flange, 150 lb pattern, 2.670 Bored Diameter, with Cam-lock Connector, Stainless Steel
BORED PIPE FLANgE
Product DescriptionPF-3BLS 3” Pipe Flange, 150 lb RF, Blind, Raised Face, 7-1/2” OD, 6” Bolt Circle Diameter,
Stainless SteelPF-4BLS 4” Pipe Flange, 150 lb Pattern, Blind, Raised Face, 9” OD, 7-1/2” Bolt Circle
Diameter, Stainless SteelPF-6BLS 6” Blind Pipe Flange, 150 lb Pattern, 11” OD, 9-1/2” Bolt Circle Diameter,
Stainless Steel
BLIND PIPE FLANgES
Product DescriptionPF-2T 2” Threaded 304 Flange, 6” OD, 4-3/4” Bolt Circle Dia. Carbon SteelPF-3T 3” Threaded Pipe Flange, 150 lb., Pattern, 7-1/2”
OD, 6” Bolt Circle Diameter, Carbon SteelPF-4T 4” Threaded Pipe Flange, 150 lb., Pattern, 9” OD,
7-1/2” Bolt Circle Diameter, Carbon SteelPF-6T 6” Threaded Pipe Flange, 150 lb., Pattern,
11” OD, 9-1/2” Bolt Circle Diameter, Carbon Steel PF-3TA 3” FnPT Threaded Pipe Flange, 150 lb., Pattern,
7-1/2” OD, 6” Bolt Circle Diameter, Cast AluminumPF-4TS 4” FnPT Threaded Pipe Flange, 150 lb., Pattern,
9” OD, 7-1/2” Bolt Circle Diameter, Stainless SteelPF-6TS 6” FnPT Threaded Pipe Flange, 150 lb., 11” OD,
9-1/2” Bolt Circle Diameter, Stainless Steel PF-3T16 3” Threaded Pipe Flange, 150 lb., Pattern, 7-1/2”
OD, 6” Bolt Circle Diameter, Carbon SteelPF-4T16 4” Threaded Pipe Flange, 150 lb., Pattern, 1” FnPT,
9” OD, 7-1/2” Bolt Circle Diameter, Stainless SteelPF-4PG38S 2” Pipe Flange, 150 lb Pattern, 6” OD, 4-3/4” Bolt Circle Diameter, with 2” Pipe
Packing Gland, Stainless SteelPF-6PG38S 6” Pipe Flange, 150 lb., Pattern, 11” OD, 9-1/2” Bolt Circle Diameter, with 2” Pipe
Packing Gland, Stainless Steel
THREADED PIPE FLANgES
PIPE FLANgE
Product DescriptionPFC-2.5S 2.5” Probe Flange Cap Assembly, Consists of 304 Stainless Steel Bevel Seat
Cap and nutPFC-2S 2” Probe Flange Cap Assembly, Consists of 304 Stainless Steel Bevel Seat
Cap and nut
PROBE FLANgE CAP
Product DescriptionPF-4PG38S 4” Pipe Flange, 150 lb Pattern with 2” Pipe Packing Gland (For Use with Probes
with Pitot Option, Pipe Outersheath), Stainless Steel PF-346S Flange Plate with 2-3/8” Hole for 2” Pipe. Fits 3”, 4” & 6” Ports, SSPF-46XT32S 2” FnPT Probe Support with Extension
11b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
Product DescriptionPF-346PG38 Packing Gland Flange Fits 3”, 4”, 6”,
Includes Packing Gland for 2” Pipe, Stainless Steel
PACKINg gLAND FLANgE
Bored Bushings Reducing Bushings
Product Description64M/32F-CS Reducing Bushing, 4” MnPT-2” FnPT, Carbon Steel48M/32F-CS Reducing Bushing, 3” MnPT-2” FnPT, Carbon Steel32M/16F-B Reducing Bushing, 2” MnPT-1” FnPT, Brass32M/24F-B Reducing Bushing, 2” MnPT-1.5” FnP, Brass
REDUCINg BUSHINgS
Product Description32M/16B-B Bored Bushing, 2” MnPT X 1.035” Bore, Brass32M/24B-B Bored Bushing, 2” MnPT X 1.535” Bore, Brass32M/32B-B Bored Bushing, 2” MnPT X 2.035” Bore, Brass
BORED BUSHINgS
Packing glands
Cam-LockPacking glands
OversheathPacking glands
PF-4/6UCLS
Pg-32/40CL
PF-4/40CLS PF-6/40CLS
Product DescriptionPG-24T 1-1/2 inch Oversheath Packing Gland, Steel Body, 1-1/2 inch MnPT,
TFE PackingPG-32S 2” Oversheath Packing Gland, Steel Body, 2” MnPT, PTFE
Ferrule includedPG-32/40CL 2” Oversheath Packing Gland, Steel Body, TFE Packing
(for use with PF-40CLS flange) with size 40 Cam and Groove Connector
PG-38/48CL 3” Oversheath Packing Gland, Stainless Steel body, Cam-Lock, For use with Pitot Version Mercury Probes with Pipe Oversheath
OVERSHEATH PACKINg gLANDS
PACKINg gLAND ACCESSORIES
Product DescriptionPG-32F 2” Adapter, Threaded Bevel Seat, #21-2, Custom Bore, 2.125” ID, Used
in PG-32S, Stainless Steel, note: Does not Include nut or Ferrule PG-32nT 2” Adapter, Bevel Seat, #21-2, Custom Bore, 2.125” ID, Welded to PF-
XXX Flange Assembly, Extention, or PC-XXX. note: Does not Include nut or Ferrule
PG-38F 2.5” Custom Threaded Ferrule, Part of PG-38-3Q Packing Gland, Stainless Steel
PG-38RT Thrust Ring, 2.435 ID X 2.875 OD, for PG-38-3Q Packing Gland, Stainless Steel
PG10-4n Pressure Gauge, 0-15 psi, 1/4” nPT, Stainless Steel PG200-4n Pressure Gauge, 1/4” nPT
PACKINg gLANDS FOR PITOTS
Product Description12MTC12-B 3/4” Packing Gland for Pitot with 3/4” Oversheath, Includes nylon
and Brass Ferrules, Brass12MTC12-S 3/4” Packing Gland for Pitot with 3/4” Oversheath, Includes nylon
and Ferrules, SS16MTC16n-B 1” Packing Gland for Pitot with 1” Oversheath16MTC16n-S 1” Packing Gland for Pitot with 1” Oversheath,
Includes Stainless Steel Ferrule16MTC16n-SF 1” Packing Gland for Pitot with 1” Oversheath, includes nylon Fer-
rules, Stainless Steel, and 16MTC16-S12F-GR 3/4” Graphite Ferrule, Alternative Packing for 16MTC1616F-GR 1” Graphite Ferrule, Alternative Packing for 16MTC16
360 DEgREE COMPASS ROSE FLANgE
Product DescriptionPF-346T32A360 Flange with 360 Degree (0-90 Degree X 4) Compass Rose Laser
Engraved. 2” Half Coupling Welded. Fits 3”, 4” and 6” Flanges. Includes Arrow Pointer for 2” Oversheath Probe, Stainless Steel
PF-346XT32S360 Flange with 360 Degree (0-90 Degree X 4) Compass Rose Laser Engraved. 2” Half Coupling Welded. Fits 3”, 4” and 6” Flanges. Includes Arrow Pointer for 2” Oversheath Probe. With Bored Bushings and 2” Diameter Probe Support Extension, SS
Product DescriptionPFC-40S-CL 2.5” nPT 316 with Buckles, Cap Cam with Groove Fitting, Type D,
2.5 inch MnPT, SS
PIPE FLANgE ACCESSORIES
Product Description64RUC32-CS Coupling, Reducer, 4” x 2” FnPT, Carbon Steel48RUC32-CS Coupling, Reducer, 3” x 2” FnPT, Carbon Steel
REDUCINg COUPLINgSReducing Couplings
12b 800-882-3214 /919-557-7300 www.apexinst.com
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
ORIFICE FLOW METERS
OFM-SERIES ORIFICE FLOW METERS
The OFM-Series Orifice Flow Meters all feature a calibrated, stainless steel critical orifice with two liquid-filled vacuum gauges and stainless steel inline filter. All fittings, including the orifice and filter, are made of stainless steel and include 1/4” tube fitting end connections. These adapters are used with vacuum pumps to provide constant sample flow rates. Orifice sizes range from 4 to 35 providing flow rates from 0.076 Lpm to 6.1 Lpm.
VUA-SERIES LOW FLOW ADAPTERS
The VUA-Series Low Flow Orifice Adapters feature a calibrated, critical sapphire orifice with liquid filled vacuum gauge, brass fittings and inline filter to adapt to Apex Instruments’ isokinetic source samplers for methods requiring low flow sampling. The adapters are used for VOST and Method 6-type sampling. Adapters include 1/2” male and 1/4” female brass quick connects to attach the isokinetic source sampler to the VOST VU-cords. Three adapters are offered to provide approximately 1/2, 1 and 2 liters per minute flow rates. The VUA-575 is used for Method 7C to provide the required flowrate between 400-500cc/min.
Product Description
VUA-561 Low-flow Adapter for Isokinetic Meter Console, ~1Lpm, 1/2” male 1/4” female quick connect, brass
VUA-562 Low-flow Adapter for Isokinetic Meter Console, ~2Lpm, 1/2” male 1/4” female quick connect, brass
VUA-565 Low-flow Adapter for Isokinetic Meter Console, ~0.5 Lpm, 1/2” male-1/4” female quick connect, brass
VUA-575 Low-flow Adapter (M7C) for Isokinetic Meter Console, ~0.5Lpm, 1/2” male-1/2” female quick connect, brass
VUA-SERIES LOW FLOW ADAPTERS
Product Description
KFR-4A40SNVT Acyrlic, 0.4-5 Lpm, Stainless Steel, No Valve
KFR-4A44SNVT Acyrlic, 4-50 Lpm, Stainless Steel, No Valve
KMR-3A13SVVT Polycarbonate, 0.1-1.2 Lpm, Stainless Steel, with Valve
KMR-3A23SVVT Polycarbonate, 0.2-2.5 Lpm, Stainless Steel, with Valve
KMR-3A14SVVT Polycarbonate, 0.4-5 Lpm, Stainless Steel, with Valve
KGS-SERIES Glass Tube, Rotating Lens, MM Scales or Direct Read Index
KGR-SERIES Glass Tube, standard lens, MM Scales or Direct Read Index
Apex Instruments offers the precision machined acrylic (KFR-Series), molded polycarbonate (KMR-Series), glass tube(KgS-Series), and electronic flowmeters for a variety of applications. Available in precision engineered sizes and scales for a variety of fluids. The millimeter reference or direct read scales can be specified to meet any requirements. NIST traceable calibration certificates are available.
FLOW METERS
KFR-Series - KMR-Series - KgS-Series
Product Description
OFM-K4-14 Orifice Control Flowmeter, In-Line, w/2 liquid Filled Vaccum Gauges, Stainless Steel In-Line Filter & KA-14-SS Orifice, 1Lpm
OFM-K4-4 Orifice Control Flowmeter, In-Line, w/2 Vacuum Gauges, Stainless Steel In-Line Filter & K4-4-SS Orifice, .076LPM
OFM-K4-6 Orifice Control Flowmeter, In-Line, w/2 Vacuum Gauges, Stainless Steel In-Line Filter & K4-6-SS Orifice, .20 lpm
OFM-K4-7 Orifice Control Flowmeter, In-Line, w/2 Vacuum Gauges, Stainless Steel In-Line Filter & K4-7-SS Orifice, .28 lpm
OFM-K4-8 Orifice Control Flowmeter, In-Line, w/2 Vacuum Gauges, Stainless Steel In-Line Filter & K4-8-SS Orifice, .34lpm
OFM-K4-9 Orifice Control Flowmeter, In-Line, w/2 Vacuum Gauges, Stainless Steel In-Line Filter & K4-9-SS Orifice, .45 lpm
OFM-K4-HG Calibration Orifice, In-Line, w/ Vacuum Gauge, Stainless Steel In-Line Filter & Orifice, low flow for mercury system
Other Flow Ranges Available. CALL FOR DETAILS & PRICING.
OFM-SERIES ORIFICE FLOW METERS
Other Flow Ranges Available. CALL FOR DETAILS & PRICING.
FLOW METERS (ROTAMETERS)
13b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
INCLINOMETERS
The INC-A2T-50 Inclinometer Sensor is designed for measuring the yaw angle of flow in accordance with Method F&G. The standard collar is designed for clamping onto 2” tubing. Remote Inclinometer Sensor, 360 degrees with 2” Tube Clamp and Amphenol Connector has analog voltage output. Alternative clamp sizes are available upon request. This remote sensor is designed to be used with the 3-D flow console, however it can be used with the Remote Digital Display (INC-D205). The inclinometer sensor is connected to the display via our standard 4-pin Signal Cable.
InC-a2t-50
PROTRACTOR / INCLINOMETERThe M5C-4 Protractor/Inclinometer is an ideal tool for measuring cyclonic yaw angles in accordance with Method 2. The machined aluminum frame and integral baseplate provide a light, rigid and ultra precise platform allowing the state-of-the-art sensor to provide unsurpassed accuracy throughout the 360° range. The inclinometer can be securely attached to probe with one of the following mounting brackets.M5C-4
INC-A2T-50INC-D205
Bracket for M5C-4 with 1” Aluminum Clamp.M5C-4-16
Bracket for M5C-4 with 2” Aluminum Clamp.M5C-4-32
Mounting Brackets for M5C-4
PENDULUM STYLE INCLINOMETEREasy-to-use, hand-held Pendulum Style Inclinometer. 1/10deg accuracy: Includes plastic case.. The dial is 2.6”dia. with vernier divisions of 1/10deg. Height is 3.6”, width is 3.1”, wt :3.6oz.InC-a300
Features:• Reliable: 15 years of proven DryCal® performance
• Accurate: Backed by ISO 17025; NV LAP accredited• Portable: Lightweight and impact-resistant• Simple: Quick Start operation and no messy soap solutions
• Streamlined: Bios optimizer software transfers calibration data directly to any windows based PC using built in serial port.
FLOW CALIBRATOR/PISTON PROVER / BIOS Defender 510 and 520 Series are the next generation of DryCal® technology. It is the proven and reliable foundation of all BIOS primary standards, and the basis of our ISO 17025 accreditation by NVLAP of NIST. Available in low, median or high ranges.
Model Description
200-510H Flow Calibrator, Defender 200-510H, High Flow Range, 300ml-30,000ml/min, +/-1% of Reading Volumetric
200-510L Flow Calibrator, Defender 200-510H, Low Flow Range, 5ml-500ml/min, +/-1% of Reading Volumetric
200-510M Flow Calibrator, Defender 200-510H, Medium Flow Range, 50ml-5000ml/min, +/-1% of Reading Volumetric
200-520H Flow Calibrator, Defender 200-510H, High Flow Range, 300ml-30,000ml/min, +/-1% of Reading Volu-metric, Includes Temperature and Pressure Recordings
200-520L Flow Calibrator, Defender 200-510H, Low Flow Range, 5ml-500ml/min, +/-1% of Reading Volumetric, Includes Temperature and Pressure Recordings
200-520M Flow Calibrator, Defender 200-510H, Medium Flow Range, 50ml-500ml/min, +/-1% of Reading Volumetric, Includes Temperature and Pressure Recordings
200-530H Flow Calibrator, Defender 200-510H, High Flow Range, 300ml-30,000ml/min, +/-1% of Reading Volumetric
200-530L Flow Calibrator, Defender 200-510H, Low Flow Range, 5ml-500ml/min, +/-1% of Reading Volumetric
200-530M Flow Calibrator, Defender 200-510H, Medium Flow Range, 50ml-5000ml/min, +/-1% of Reading Volumetric
M5C-4INC-A300
BIOS DEFENDER 510 AND 520 SERIES
FLOW CALIBRATORS
REMOTE INCLINOMETER LED DISPLAY (INC-D205)The INC-D205 Remote Inclinometer Display is designed to be used inconjunction with our INC-A2T inclinometer sensor. The display is a highresolution 3 1/2 digit bright LED process meter. The meter is housed in a sturdy compact metal cabinet with convenient carrying handle. RequiresINC-A2T Sensor and Signal Cable (INC-SC-”length”). SC voltage 120/60Hz.Dimensions: 6” x 7” x 8.5”Weight: 4 lb.
InC-d205InC-a2t-50
14b 800-882-3214 /919-557-7300 www.apexinst.com
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
Apex Instruments Differential Pressure and Temperature Monitor accurately measures the differential pressure and temperature when used in conjunction with a Pitot Tube and Type-K Temperature Probe. This instrument is for continuous monitoring of stack gas velocities when coupled with a data logger. This compact bench top differential pressure and temperature monitor incorporates a digital manometer display with a temperature display. The connections (power cord, 2 Female 1/4” quick connects, terminal strip and Type-K thermocouple outlet), are located on the back panel of the case; all the readouts and switches are mounted on the front panel. It has a convenient folding handle making this unit easy to transport. Bench top version uses a pressure transducer that is stable and reliable.
DIFFERENTIAL PRESSURE / TEMPERATURE TRANSDUCER DISPLAY
Features:• Digital Pressure Display• Type-K Temperature Display• Voltage Output Signals• Durable Compact Cabinet• Stainless Steel 1/4” Quick Connects• Terminal Strip - Output Signal• 25” Transducer
Specifications: Pressure Range: 0.1”. Temperature Display Accepts Type-K Thermocouple. Resolution 1°C or F; Range: -157 to 1999°F; Supply Voltage +/- 5Vdc; Ratiometeric based 0.25 to 4.0 Vdc, 120V/50-60Hz; Power: 120 VAC/60 Hz;Dimensions: HxWxD 6” x 7” x 8.5”; (15.2 cm x 17.8 cm x 21.6 cm).
TRANSDUCERS/TRANSMITTERS
M-DP-10 TRANSDUCER/TRANSMITTER10 Inch Single Transducer, Gage 0-10 Inch. Populated Printed Circuit Board with One 0-10 “ H2O. Mounted in Plastic Enclosure. 12VDC Supply Required. Sensor Ranges (1, 2.5, 5, 10 and 20) Add “B” for bidirectional.
M-dP-10
THERMOCOUPLE TRANSMITTER4 Channel Thermocouple Transmitter. 4.4 x 2.4 x 1.1 ABS plastic enclosure with terminal blocks. Designed using Analog Devices AD595CQ TC amplifier with cold junction compensation. Low input impedance and +/- 1 degree C accuracy.
M-tC4C
M-DP-10 TRANSDUCER / TRANSMITTER Features:• Temperature Compensated Pressure Transducers• Built into 4.4” x 2.4” x 1.1” Enclosure with Terminal Blocks• Accessible Hose Barbs for Pressure Connections (barbs OD=.174 -.190)• Built-In ESD Protection• 12vdc Power Required from Separate Source• Operating Range of 0-70°C• Relative Humidity Operating Range of 0-95%• Ratio Metric 4vdc Span Output (exact output value is sensor dependent)• On-board Regulated Reference Supply for Pressure Sensors
FOUR CHANNELTHERMOCOUPLE TRANSMITTER Features:• TVS Diodes on TC Input for ESD and Transient Suppression• DC-DC Converter on 12V Power input Providing 1000V Power Surge Isolation• Designed using Analog Devices AD595CQ TC Amplifier with Cold Junction Compensation, Low Input Impedance and +/- 1°C Accuracy• Low Power Consumption (less than 40ma for all 4 channels)• Type K Thermocouple Range Capable
DPT-B1
Product Description
DPT-B1 Differential Pressure and Temperature Transmitter/Display Pressure Range 0-1”
DPT-B2 Differential Pressure and Temperature Transmitter/Display Pressure Range 0-2 “
DPT-B5 Differential Pressure and Temperature Transmitter/Display Pressure Range 0-5 “
TRANSDUCER DISPLAYS
M-TC4CM-DP-10
15b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
HAND HELD DIgITAL MANOMETERS
The DP-CALC™ 5825 micromanometer allows you to easily make HVAC pressure measurements. These robust instruments can be used with Pitot probes to measure duct velocity. The high performance DP-CALC 5825 can calculate flow and has data logging capabilities.
dHM-5825
Features:• Measure Differential and Static Pressure from -15 to +15 in. H2O. • Calculates Velocity when used with Pitot Tube • Quick Zero Function Ensures Accurate Readings • Performs Flow Rate Calculations from User-Input Duct Size or K-Factor • Stores 12,700+ Samples and 100 Test IDs • Data Logs with Time and Date Stamp• LogDat2™ Downloading Software
DHM-5825 DIgITAL HANDHELD MANOMETERS
DHM-5825
The DHM28-10 is a precision instrument designed to measure a wide range of pressures to a very high ac-curacy. Features include: measurement in all common pressure ranges, display resolution to .001, differential or relative measurement, two line liquid crystal display, and adjustable auto power off to conserve battery. A certificate of calibration is included with the unit at no additional cost. The DHM28-10 can be used as a secondary calibration standard for your other pressure instrumentation.
dHM28-10
DHM28-10 DIgITAL HANDHELD MANOMETERS
DHM28-10
Features:• Microprocessor Based• Differential Gage, or Absolute• High Accuracy, 0.2%, 0.1%, or 0.5% with Calibration Certificate• Selectable Scales• Resolution to 0.000 of Selected Unit • Input Range; US 0-10” in H2O, Metric 0-2.5 kPa, Overpressure 12.5 kPa (50 in H2O)• Accuracy, ±0.20% Full Scale ±1 Digit• Hold Function• Programmable Display• Memory for up to 964 Readings• Output for Optional Printer or Computer Interface
The DHM-M100 handheld manometer combines form, fit and function to deliver precision pressure measurement for field, plant or lab use. Applicable to leak testing for low pressure gas systems, pressure drop monitoring across filters, monitoring vacuum on condensers or pumps, and verification of CPAP or BIPAP systems for home or hospital settings.
dHM-M100
DHM-M100 MERIAM DIgITAL HANDHELD MANOMETER
DHM-M100
Features:• Lightweight and Ergonomic• Sealed Membrane Type with 4 Dome Style Contact Buttons • Measure Differential - Range 0 to 28.00” H2O • 8 Selectable Engineering Units: Inches of H2O at 20°C, mm of H2O at 20°C, mm of Hg at 0°C, Inches of Hg at 0°C, kPa, mBar, Bar, PSI and User Selectable• English/Metric Units• Accuracy ±0.25% F.S.
Low Cost Hand Held Manometer for Differential Pressure Measurement
• Automatically Powers Off after 20 Minutes of Keypad Inactivity• Stores up to 240 Pressure Measurements• Green Backlight is User Activated Via the Backlight Key• Red Backlight is Automatically Activated During an Error/Over Range Condition• Certificate of NIST Traceability (optional)
Link to Pitots
16b 800-882-3214 /919-557-7300 www.apexinst.com
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
standard Pitot18 inch Standard Pitot Tube, 5/16 inch diameter Stainless Steel.
160-18
AIR VELOCITY KITSThe M-115AV Air Velocity Kit includes an Inclined Portable Manometer with a range of -.05” to 0.25” H2O with 0 to 0.5” minor scale divisions, standard 12” pitot, hoses and a case. The DP-CALC Manometer can be ordered separately. Cus-tom Kits Available.
DELUXE METHOD 2 PRETEST SURVEY KIT
Features:• 1” Thick Acrylic Plastic Body• Drilled Bore Accurate to ±.0002 inches• Selected Gauge Oil• Adjustable Reflective Chrome Finish• Parallax-Free Reading• Screw Type Leveling Adjustment
CASE withM-115AV KIT
standard Pitot6 inch Standard Pitot Tube, 1/8 inch diameter Stainless Steel.
166-12
Includes all items of the SK-DM2D (Listed Above) with 4 Magne-helic Gauges: 0 to 0.25”H2O, 0 to 2” H2O, 0 to 5” H2O, and 0 to 10” H2O in lieu of digital manometer (English Units).
sK-dM2
DELUXE METHOD 2 MAgNEHELIC KIT
Includes all items of the SK-DM2D (Listed Above) with 4 Magnehe-lic Gauges: 0-.25CM H2O, 0-6 mm H2O, 0-50 mm H2O, and 0-100 mm H2O in lieu of digital manometer (Metric Units).
sK-dM2M
DELUXE METHOD 2 METRIC MAgNEHELIC KIT
INCLINED PORTABLE MANOMETERInclined Portable Manometer with a range of-.05 to 0.25”.
M-115
M-115
DUAL SCALE PORTABLE INCLINED-VERTICAL MANOMETERThe M-400K Air Velocity Kit includes Dual Scale Portable Inclined-Veritical Manometer (M-400G) with an inclined range of 0-1.0” H2O with .01” minor divisions and vertical range of 1 to 10” H2O with 0.10” minor divisions, 18” standard pitot, hoses and case (M-400G Manometer can be ordered separately).
M-400K
Features:• 1 1/4” Thick Acrylic Plastic Body
• 3/16” Bores, Accurate to ±.0002”
• Selected gauge oil
INCLINED/VERTICAL PORTABLE MANOMETERPortable Inclined/Vertical Manometer with a range of 0 to 10.
M-400g
ROLL-UP MANOMETERRoll-Up Manometer, Range 18-0-18”, quick shut off hose barb connections.
M1211-36
M1211-36
The Deluxe Method 2 Pretest Survey Kit contains a modular pitot tip and extension for stacks up to 12’, a digital hand held manometer, thermocouple thermometer, tubing, reducers, unions and flexible thermocouples. The kit is packagein a sturdy, foam-linedcase. Custom kitsavailable. Alternativemanometer optionsavailable upon request.
SK-DM2D KIT & CASE
• Ground Glass Bubble Level
• Parallax-Free Reading
• O-Ring sealed Fluid Level plunger Adjustment
sK-dM2d
M-400g
160-18
CASE withM-400K KIT
17b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
MAgNEHELIC gAUgES
MAG-2000-00 0-1/4” H2O
MAG-2000-0 0-1/2” H2O
MAG-2001 0-1” H2O
MAG-2002 0-2” H2O
MAG-2005 0-5” H2O
MAG-2010 0-10” H2O
A-369 Stand, Aluminum, 5 1/2” Tall
MAG-2000-6MM 0 to 6 mm H2O
MAG-2000-25MM 0 to 25 mm H2O
MAG-2000-50MM 0 to 50 mm H2O
MAG-2000-100MM 0 to 100 mm H2O
Easy to read 4” dials indicate gas pressures; positive, negative or differential. The gauges have a + 2% full scale accuracy and include simple, frictionless magnehelic magnetic movement. They are highly resistant to shock, vibration and overpressure.
STANDARD MEASURE METRIC MEASURE
ANEMOMETERS
Hot Wire Anemometer with two miniature glass-bead thermistors provides greater precision at low air velocities. Telescope probe expands from 9.2 inches to 3 feet for hard-to-reach places. Eliminate friction errors caused by rotating vanes with this no-moving parts. Serial RS-232 output allows anemometer to be connected to a computer or data logger for monitoring results. Memory function recalls the highest and lowest readings. A data hold button freezes the display to capture readings. Unit is supplied complete with dual thermistors probe, 40-inch cable, carrying case, Traceable® Certificate, 6 AAA batteries, and serial computer output.
an-4330
LCD display reads airflow from 40 to 7800 feet per minute and 0.20 to 40.00 meters per second. Select 2 or 16-second averaging. Memory recalls highest/lowest readings for any time period, and a HOLD switch freezes the display to capture a reading. The sensing probe can be handheld or used with the supplied extension wands to increase reach by 5 feet. Vane is aluminum and case is ABS plastic.
an-4090
HOT WIRE ANEMOMETER
Features:• Range is 40 to 7800 Feet Per Minute and 0.20 to 40.00 Meters Per Second• Resolution is 1 Foot Per Minute or 0.01 Meter Per Second• Accuracy is ±1%• Extension Wand Increases Reach by 5 Feet• Supplied with Two AA Alkaline Batteries• Dimensions: HxWxD 3” x 7” x 3/4” ( 7.6 cm x 17.8 cm x 1.9 cm); 8 oz (.23 kg).
Features: • Five Ranges Anemometer Accuracy is ±(1% full scale + 1 digit)• Temperature Accuracy is ±0.8°C (1.5°F)• Dual thermistors Probe with 40” Cable• Dimensions: HxWxD 7” x 3” x 1.25” (17.8 cm x 7.6 cm x 3.2 cm); 9.5 oz ( .23 kg)
AN-4090
AN-4330
MAg-2000-00
18b 800-882-3214 /919-557-7300 www.apexinst.com
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
BAROMETERSHandheld Digital BarometerHandheld Digital Barometer measures altitude, temperature, and barometric pressure. Also has a stopwatch/time of day clock and graphically displays the barometric pressure trend. Barometric pressure trend shows current reading and previous 2-, 4-, 6-, 8-, 10-, and 12 hours in bar-chart format. Barometric pressure reading is updated every 15 minutes. Altitude is displayed in meters or feet. Reading is updated every 2 seconds. Features a minimum/maximum memory for the altitudes reached during any time period.Temperature display is updated every 10 seconds. Clock displays the time of day to the minute and shows the date and month. The clock also features a format of 12-/24-hour timing and an alarm.
Bar-4198
Specifications: Barometric pressure: Measures 15.90 to 31.01” Hg with a resolution of 0.03 Hg and from 400 to 1070 mbar with a resolution of 1 mbar with accuracy: ±0.2363 Hg (±8 mbar). Altitude: -500 to 7000 meters (-1640 to 22,965’), with a resolution of 1 meter or 1 foot. Thermometer displays: -40.0 to 158.0°F and -40.0 to 70.0°C with a resolution of 0.1°, accuracy is ±1°C. Stopwatch: times from 1 second to 99 hours, 59 minutes, 59 seconds · Resolution is 1 second and accuracy is 0.01%
MUTLI-FUNCTION HOT WIRE ANEMOMETER
Features: • Single Probe Capable of Measuring Air Velocity and Temperature Simultaneously• Built-In-Memory Allows Storage of Measured Data• Highly-Visible LCD is Capable of Displaying Air Velocity and Temperature• Carrying Case, Operation Manual • RS-232C Cable, AC Adapter, 6x AA Batteries and Software (for Windows)• Data can be Reviewed On-Screen, Printed, or Downloaded to a Computer
Hot Wire Anemometer with two miniature glass-bead thermistors provides greater precision at low air velocities. Telescope probe expands from 9.2 inches to 3 feet for hard-to-reach places. Eliminate friction errors caused by rotating vanes with this no-moving parts. Serial RS-232 output allows anemometer to be connected to a computer or data logger for monitoring results. Memory function recalls the highest and lowest readings. A data hold button freezes the display to capture readings. Unit is supplied complete with dual thermistors probe, 40-inch cable, carrying case, Traceable® Certificate, 6 AAA batteries, and serial computer output.
an-a031
Specifications: Air Velocity Range: 20-6000fpm (0.10-30 Om/s). Air Velocity Accuracy: +/-2% of reading or +-3fpm whichever is greater. Temperature Range: -4 to 140.0 F (-20 to 60.0°C). Temperature Accuracy: +/-1°C). Data Logging: Up to 800 measurements. Probe Type: Straight. Probe Dimensions: Length 39.4 in. (100 cm) - Telescopic / Diameter of Tip; 0.236 in.
AN-A031
BAROMETER 6-LINE DIgITALTraceable® Barometric Pressure/Humidity/Temperature Meters Electronic digital barometers measure atmospheric pressure, graphically display the barometric trend, and report relative humidity and temperature.
Bar-4195
Specifications: Barometer measures pressure from 23.45 to 31.01 (inHg) with a resolution of 0.03 inHg,(794 to 1050 mbar) · Accuracy is ±0.1477 inHg (±5 mbar) · Display relative humidity with a resolution of 1% · Accuracy is ±5 RH · Temperature range is from 32 to 131°F and 0 to 55°C · Temperature accuracy is ±1°C
BAR-4198
19b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
TEMPERATURE MEASUREMENTThe Total-Range Thermometer can switch from °F to °C at the touch of a button. Unit features HOLD button that freezes display to capture current reading. A microprocessor updates the display twice a second. Uses all Type-K thermocouple probes. Alarm function may be set in 1° increments. Sound signals when time is reached. Back-lighting button permits reading in dark areas. Comes ready to use with PVC protective casing with flip-out stand. Batteries power unit for 1 year of routine use. Jumbo-size, 5/8-inch-high digits, constructed of shock-resistant ABS plastic. Water-resistant case stops dirt, dust, fumes, and water.
tC-4015
2 CHANNEL THERMOMETER Provides recessed front panel adjustable offsets on two channels allowing user to adjust thermometer exactly to a specific temperature, in-house calibration, or particular sensor for increased accuracy. Provided rubberized case makes it a virtually “environment-proof” instrument for all weather, shock, and abusive conditions. Supplied with Velcro™ wrist strap. Built-in stand makes it ideal for lab bench. Large LCD display shows temperatures of probe 1, probe 2, or the difference (delta) of the two probes. Readout in °F and °C. Extra-large, 3/4-inch-high display is readable from 12 feet. Max button captures the highest reading achieved. HOLD button freezes display to capture current reading. Uses all Type-K thermocouples. Supplied with two immediate-response probes which indicate temperature changes in less than one second.
tC-4135
WORKHORSE THERMOMETER Type-K Workhorse™ Thermometer provides a sharp readout in dim and very bright light, long battery life (150 to 200 continuous hours), high accuracy, wide temperature range, and a new chip design for an ultra low Price. Recessed front panel adjustable offset allows user to adjust thermometer exactly to a specific temperature, in-house calibration, or a particular sensor for increased accuracy. HOLD button freezes display to capture current reading. Supplied with bench stand. It is compatible with all Type-K probes. Supplied with fast response Type-K probe, bench stand, 9-volt battery, and carrying case. Cable length of 40 inches.
tC-4425
WATERPROOF THERMOMETERWaterproof Thermometer has membrane switches, ABS body, and stainless steel probe, good for use in labs, plants, wash-down areas, and the field. Unit eliminates the dangers inherent in breakable glass and toxic mercury thermometers. It displays minimum and maximum readings over any period. Unique holder allows probe to be positioned at any height while attached to beakers, stainless cylinders, or vats. Probe guard snaps to handle to extend overall length to 10.75”. Readings are updated every second. Supplied with probe holder, key chain, and lanyard. Operates continuously for 1.5 years on supplied replaceable silver-oxide battery.
dPt-168-nIstSpecifications: Range: -58 to 572°F and –50 to 300°C. Resolution: is 0.1° from –20 to 200° (1° otherwise). Accuracy: ±0.4°C or ±1.5°C. Dimensions: stem length, 3.25” inches; stem diameter is 0.14”; overall length is 7.25”. Weight is 1 oz.
THERMOMETERS
Specifications: Range: -328 to 2498°F and -200 to 1370°C. Resolution: 0.1° and 1°. Accuracy: ±1°C between -50°C to 740°C, otherwise ±2°C. Dimensions: 3.25” x 7 x 1.5” ( cm x cm x ); 8 oz ( kg).
Specifications: Range: -58 to 2000°F and -50 to 1300°C with1° resolution. Accuarcy: is ±0.3% plus 1°C.Dimensions: HxWxD 2.75” x 5.25” x 1.25” ( cm x cm x cm); 5.25 oz
Specifications: Range: -58.0 to 2372°F and -50.0 to 1300°C. Accuracy: ±(1°C + .75%) between 0 to 500°C; ±(1°C + 1%) 500 to 750°C; ±(1°C + 2%) 750 to 1000°C; ± (3°C + 4%) 1000 to 1200°C; ±2°C at –20; ±3°C at –40; and ±4°C at –50). Resolution: 0.1° between –50.0 to 200.0 and 1° elsewhere Probe dimensions: length is 5” and .175” diameter . Thermometer Dimensions: 2.75” x 5.5” x 1.25” ( cm x cm x cm); 6 oz ( kg).
TC-4015
TC-4135
TC-4425
DPT-168-NIST
20b 800-882-3214 /919-557-7300 www.apexinst.com
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
Red Spirit Filled Thermometer with a Range of 20° to 120°F. It is fast and accurate with no assembly required. Includes high impact on plastic construction.
B12-7012
HUMIDITY
Sling Psychrometer
Monitor shows current, minimum, and maximum displays and includes a settable high/low alarm for all four readings (dew-point, wet-bulb, humidity, temperature). Alarm may be set in 0.1 increments, it sounds for one minute and red LED flashes until readings return to non-alarm condition. Meets federal requirements for CLIA specification 493.1207 for monitoring temper-ature and humidity. Supplied with two AA alkaline batteries for continuous, 1-year “always on” monitoring, and Traceable® Certificate. LCD digits are 1-inch-high. Case is high-impact, chemical-resistant ABS plastic.
HuM-4410
DEW-POINT/WET-BULB/HUMIDITY/THERMOMETER
MODEL 520 PIE (PRACTICAL INSTRUMENT ELECTRONICS) THERMOCOUPLE SIMULATORSPrecise temperature inputs to all types of instruments, transmit-ters, recorders, controllers, alarms, data acquisition and computer systems. Provides 18” extension wire output and is cold junction compensated for changes in ambient temperature. Accurate source for checkout and calibration of all thermocouple instruments. Practi-cal Instrument Electronics (PIE) Model 520 Thermocouple Simulator simulates a dedicated standard thermocouple curve over the entire industrial temperature range.
M5C-520
Specifications:
Temperature Range: –40 to 70 °C and –40 to 158°F
Resolution: 0.1° (below 100. Accuracy: ±1°C
Relative Humidity Range: 1 to 99%
Resolution: 0.1%RH. Accuracy: ±4% between 20 to 80%
Dimensions: HxWxD 4.125” x 4.125” x 1”. Weight is 4.25 ounces
B12-7012
HUM-4410
M5C-520
21b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
Type-K Thermocouple Assembly
Type-K Thermocouple Assembly with standard plug, inconel sheath, magnesium oxide insulation, 1/8” outer diameter. Maximum Temperature 1800°F.
TYPE-K THERMOCOUPLES
tCa-12Mg212” Type-K Thermocouple Assembly
tCa-24Mg224” Type-K Thermocouple Assembly
tCa-38Mg238” Type-K Thermocouple Assembly
Model Description
WK-PP-24 24GA-Solid, Polyvinyl
WK-PP-24S 24GA-Stranded, Extension
WK-HH-24 24GA-Solid, TYPE K, HITEMP Glass
WK-TT-24 24GA-Solid, TYPE K, Teflon®
WK-TT-24S-SB 24GA-STR, TYPE K, Teflon®, stainless steel Overbraid
WK-XC-24 24GA-Solid, High Temp Glass Insulated, Ceramic
WK-125CI MGO Insulated, Type K, I600
Custom thermocouple cable assemblies made to order. Multiple lines and braided oversleeving available. Quantity discounts are available. Call for more details and pricing.
THERMOCOUPLE WIRE TYPE-K
These bushings are installed into an insert indentation of the connector and provide strain relief for thermocouple wire.
RUBBER BUSHINgS
tC-rB
Thermocouple Bushing, Rubber Cord (standard size)
tC-MrB
Thermocouple Bushing, Rubber Cord (miniature size)
Apex Temperature Plugs and Jacks feature a glass filled thermoplastic body which provides high strength at temperatures up to 218°C (425°F) as well as low moisture absorption and good dielectric constant.
THERMOCOUPLE PLUgS AND JACKS
Snap-In Panel Jack, Type-K (Standard Size).tC-PJK
Snap-In Panel Jack, Type-K, Universal. tC-PJu
Snap-In Panel Jack, Type-K, Round Threaded Mount.tC-PJr
Snap-In Panel Jack, Type-K, Mini Panel Jack.tC-PJ-MK
Connector, Type-K, Female, Cord Mount, (standard size). Includes: Plug, Cover, Screws & Bushing.tC-lJ-Ka
Connector, Type-K, Male, Cord Mount, (standard size). Includes: Plug, Cover, Screws & Bushing.tC-lPs-Ka
Connector, Mini, Type-K, Female, Cord Mount.Includes: Plug, Cover, Screws & Bushing.tC-MJ-Ka
Connector, Mini Type-K, Male, Cord Mount. Includes: Plug, Cover, Screws & Bushing.tC-sP-Ka
Adapter, 1/8” Tube Union, Stainless Steel.ta-125
Adapter, 1/4” Tube Union, Stainless Steel.ta-250
Call for custom lengths.
22b 800-882-3214 /919-557-7300 www.apexinst.com
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
Flow Pressure & Temperature2-D Flow Modular System .......................... 4b2-D, Pitot..................................................... 4b2-D, Pitot Calibration .................................. 4b2-D, Software.............................................. 4b2-D, Inclinometer ........................................ 4b2-D, Manometer.......................................... 4b3-D Flow Modular System .......................... 5b3-D Console, Classic MC-3D52.................. 5b3-D Pitot (5 Hole Pitot)................................ 5b3-D Pitot Calibration ................................... 5b Accu-flow Measurement System ................ 3bAir Velocity Kits ........................................... 16bAnemometers ............................................. 17b-18bBarometers ................................................. 18bBushings ..................................................... 11bCam-Lock ................................................... 10b-11bCouplings.................................................... 11bDew-Point/Wet-Bulb Thermometer ............. 20bFlanges ....................................................... 10b-11bFlange Reducers ........................................ 11bHumidity...................................................... 20bInclinometers .............................................. 13bInclined/Vertical Manometer ....................... 16bMagnehelic Gauges.................................... 17bManometers................................................ 15b-16bMethod 2, Pretest Survey Kit ...................... 16bMethod 2, Magnehelic Kit ........................... 16bOrifice Flow Meters ..................................... 12bPort Adapters .............................................. 10b-11bPacking Glands .......................................... 7bPacking Glands .......................................... 10b-11bFlow Adapters ............................................. 12b-13bPitot Tubes.................................................. 6bPitot Assembly Options............................... 6bPitot Tube, Type-S ...................................... 7bPitots, Modular............................................ 8bPitots, Modular Components ...................... 8bPitots, Telescopic Tube Extension .............. 8bPitots, Union & Quick Connects ................. 8bPitots, Method 2C Standard Tube .............. 9bProbe, 2-D (3 Hole Pitot) ............................ 9bProbe, 2-D (3 Hole Pitot) ............................ 9bThermometers ............................................ 19bThermocouple Simulators........................... 20bThermocouple Assemblies ......................... 20bThermocouple Rubber Bushings ................ 20bThermocouple Plugs & Jacks ..................... 20bTransducer Transmitters ............................. 14bTransducer Displays ................................... 14bThermocouple Transmitter.......................... 14bRotometers ................................................. 12bSling Psychrometer .................................... 20b
Probes InclinometersManometers
23b www.apexinst.com 800-882-3214 /919-557-7300
FLOW, PRESSURE AND TEMPERATURE MEASUREMENT
Example showing circular stack cross section divided into 12 equal areas with location of traverse points indicated.
Example showing a three by four rectangular stack cross section with location of traverse points indicated.
TraversePoint
123456
Distance% of diameter
4.414.729.570.585.395.6
Rectangular StackLocation of Sampling PointsLocation of Sampling Points
Circular Stack
Number of traverse Matrix layout points 9 3x3 12 4x3 16 4x4 20 5x4 25 5x5 30 6x5 36 6x6 42 7x6 49 7x7
Kp = Velocity equation constant (34.97 metric, 85.49 English)
Cp = Pitot tube coefficient (0.84 baseline coefficient, else use wind tunnel calibration)
FEDERAL REFERENCE METHOD 2Determination of Stack gas Velocity and Volumetric Flow Rate(Type S Pitot Tube)
INPUT PARAMETERS
Area of stack (m2) or (ft2) = pr2 or p (D/2)2 or L x W = As = _________
Pitot tube coefficient = Cp = _________
Stack gas temperature (K) or (°R) = Ts = _________
Average of square root of velocity head (mm. H2O)1/2 or (in. H2O)1/2 = ( )avgp∆
= _________
Barometric pressure (mm. Hg) or (in. Hg) = Pbar = _________
Stack gas static pressure (mm. H2O) or (in. H2O) = Pg = _________
Absolute stack gas pressure (mm. Hg) or (in. Hg) = Ps = _________
Note: Ps = Pbar + Pg (mm. H2O)/13.6 or (in. H2O)/13.6
Stack gas moisture (fraction) = Bws = _________
Stack gas dry molecular weight (g/g-mole) or (lb/lb-mole) = Md = _________
Stack gas wet molecular weight (g/g-mole) or(lb/lb-mole) = Ms = _________
Note: Ms = Md (1 – Bws) + 18.0 Bws
CALCULATIONS
vS = Stack gas velocity, m/s or ft... /s
ss
avgsavgpps MP
TxpxCxKv )()( ∆=
= _______________m/s (ft... /s)
www.apexinst.com
919-557-7300 or 800-882-3214Fax: 919-557-7110
Website: www.apexinst.comContact: [email protected]
Apex Instruments, Inc.204 Technology Park Lane
Fuquay-Varina, N.C. 27526, U.S.A.
Filters
Flanges
Pre-Filter
Gas analysisEquipmEnt CataloG
20c
GAS ANALYSIS EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com
Delivery:Most orders are shipped within 24 hours of receipt. Please allow extra time for custom orders. Shipping times vary according to the requested shipping service. If you have questions about your shipment please email our shipping management at [email protected].
Return Merchandise AuthorizationCustomers wishing to return items for service or credit need to contact our sales associates for an RMA. Contact by email at [email protected] or by phone (919) 557-7300 or toll free (800) 882-3214.
PricingPrices are published for U.S. customers only. International customers should contact their local distributor. Prices are in U.S. Dollars, FOB shipping point, or Ex Works for International orders. Please confirm current prices by phone, fax or email. Please refer to our price list for a complete list of part numbers and kit configurations.
PaymentFor your convenience, MasterCard, VISA and American Express arewelcome. Company purchase orders are accepted upon credit approval.
We back up this commitment with extensive knowledge of our products, good communication and an excellent customer service history. Our equipment is designed by experienced stack testers who know what you face when performing compliance testing.
CUSTOMER SATISFACTION is guaranteed at APEX INSTRUMENTS.
Hours of Operation:Monday through Friday from 8:00 am
until 5:00 p.m. (EST).
Apex Instruments, Inc. 204 Technology Park Lane
Fuquay-Varina, NC 27526 USA
In U.S. Call Toll Free:1-800-882-3214
Local: 1-919-557-7300fax: 1-919-557-7110
e-mail: [email protected]
www.apexinst.com
We encourage you to suggest ideas to improve our equipment. We work closely with you, over the long term, to provide the best equipment for your needs.
Doug Bernhardt Customer Service
Please feel free to call our friendly sales staff today!
Vance JonesDomestic Sales,
Customer [email protected]
Janet NicholsSales Manager
John StauberInternational [email protected]
GAS ANALYSIS EQUIPMENT
FLOW, PRESSURE & TEMPERATURE
MERCURY AND GAS SAMPLING SYSTEMS & EQUIPMENT
GAS ANALYSIS EQUIPMENT
APPENDIX
INDEX
ACCESSORIES
ISOKINETIC SAMPLING EQUIPMENT
Phone: 919-557-7300 or In the U.S. 800-882-3214Monday-Friday, 8:00 a.m. to 5:00 p.m. (Eastern Time)
Fax: Order at your convenience 24 hours a day, 7 days a week 919-557-7110
Website: www.apexinst.com
Please visit our website for additional product information, new product releases, updated materials, manuals, reference data and valuable links.
gas analysis equiPment Gas sampling or constant velocity sampling requires an understanding of Methods 1 through 3, these are basic methods of collecting a sample. Apex offers source sampling solutions to complete your testing needs. The XC-60 Source Sampler is designed to extract and trap the samples needed to test for harmful gases. After the sample is collected there are many types of analysis depending on the compound(s) of interest.
Method 3 Gas Analysis for the Determination of Dry Molecular Weight
Method 3B Gas Analysis for the Determination of Emission Rate Correction Factor or Excess Air
Method 4 Determination of Moisture in Stack Gases
Method 7 Determination of Nitrogen Oxide - Emissions from Stationary Sources
Method 18 Integrated Bag Sampling for Organic Compounds
Method 0030 Volatile Organic Compounds (VOST)
Method 0031 Volatile Organic Compounds (SMVOC or SuperVOST)
Method 0040 Principle Organic Hazardous Constituents (POHCs) using Tedlar® Bags
Method 0051 Hydrogen Chlorine and Chlorine
Method 3A Determination of oxygen and carbon dioxide concentrations in emissions from stationary sources
Method 6C Determination of sulfur dioxide emissions from stationary sources
Method 7E Determination of nitrogen oxide emissions from stationary sources
Method 10 Determination of Carbon Monoxide Emissions from Stationary Sources
Method 25A Determination of Total Gaseous Organic Concentration using a Flame Ionization Analyzer
iRm - Instrumental Reference Methods & Equipment The US EPA specifies IRM Reference Methods are used to sub-stantiate the accuracy and precision of the CEMS. A Continuous Emission Monitoring System (CEMS) is the equipment that is used for the determina-tion of a gas or particulate matter concentration or emission rate using pollutant analyzer measurements, conversion equations, graphs, or computer programs to produce results in units of the applicable emission limitation or standard. CEMS are required under some of US EPA regulations for either continual compliance or when one is exceeding the standards.
Extractive Sampling Equipment..................3c
Pre-Filters, Flanges, IRM Probe, Probe Assemblies....................4c - 5c
Filter Assemblies, RATA Sampler, Tri- Sample ProbePMI Dilution Probe & Panel ...................6c - 8c
Heated Sample Line, CEM Temperature Controllers ....................9c - 10c
Gas Conditioners, Portable Conditioner, Flow Draws, Gas Analyzers .....................11c - 14c
Method 3 Orsat Analyzers,Combustion Gas Analyzers,Filter Housings, Condensers .....................15c - 18c
Gas Analysis Index ....................................19c
3c
GAS ANALYSIS EQUIPMENT
www.apexinst.com 800-882-3214 /919-557-7300
apex systems offer:
• Gas Conditioners• Flow Control Drawer• Data Acquisition
• Heated Sample Probe• Filter• Heated Sample Line• Temperature Controller
FlangeHeated Filter
Enclosure
Heated Sample Line
Stainless Steel CamlockPre-Filter Assembly
Poly Camlock
Transportable - IRM System
There are several instrumental reference methods (IRM) in 40 CFR Part 60 that are used to measure air pollutant emis-sions from stationary sources using a continuous instrumental analyzer. These include Methods 3A, 6C, 7E, 10, 20 and 25 to measure oxygen, carbon dioxide, sulfur dioxide, nitrogen oxides, carbon monoxide, and gaseous hydrocarbon organic emissions from stationary combustion sources.
ExTRACTIVE SAMPLING EqUIPMENT
4c
GAS ANALYSIS EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com
PRE-FILTERSStainless Steel IRM Filter Assembly with replaceable glass fiber filter element that accepts standard 25 m x 90 mm tapered filter thimbles. Particulate shroud to deflect large particulate and increase filter lifespan. Modular, threaded shroud design allows quick and easy replacement of the filter element. Filter retaining ring securely holds filter. Outlet has 3/8” female NPT. Optional Silcosteel coating for low NOx applications. Replaceable filter elements sold separately.
sFC-2590
Porous Stainless Steel Filters are typically used as a pre-filter for IRM In-Stack Filtration to prevent clogging of filters downstream. Filters have over 18 square inches of a 10 micron filtering surface and can be back flushed with compressed air. Apex also offers an optional particulate shroud for extra heavy dust loadings. These filter assemblies attach to the stack end of the probe liner.
SFC-2590(Shown with Tube Union
Adapter)
SFC-2590(Inside View with GF-2590 element)
IRM PROBEIRM Probe Assemblies incorporate the popular heater design from the Method 5 probes so liners can be changed in seconds without disturbing the heater. The separate heater tube provides even heat distribution and isolates the electrical elements from the liner. The probe sheaths are constructed with a 2” stainless steel outersheath with a tube nut welded to the end for attachment to a porous filter or a bored cap. Probes are available in any length from 2’ to 20’. The probes are manufactured to accommodate standard wattages or customized for hotter conditions. Add “V” to end of part number for 240 VAC.
All IRM Probe Assemblies are available with 1” or 2” OD Stainless Steel Sheath, 2” OD stainless steel sheath with a heater and a liner made from stainless steel, inconel, quartz or glass (120 VAC/60 Hz). Classic 1” OD stainless steel sheath is also still available.
FlangePorous FilterAssembly
Stainless Steel Camlock
IRM Probe
SSF-64N10-P
Stainless Steel Pre-Filters
Part # Description
SSF-64N10 Sintered Stainless Steel Filters, 10 Micron, 6” Length, 1/4” FNPT Fitting
SSF-64N10-P Sintered Stainless Steel Filters, 10 Micron, 6” Length, 1/4” FNPT Fitting with 1.25” OD Particulate Shroud
LengthBlank = No ShroudP = Particulate Shroud1/4 Inch FNPT
10 Microns
Male Straight Connector (Not Included with SSF-64N10 or SSF-64N10-P)
Part # Description
4MSC4N-S 1/4” Tube Fitting to 1/4” MNPT, Stainless Steel
6MSC4N-S 3/8” Tube Fitting to 1/4” MNPT, Stainless Steel
8MSC4N-S 1/2” Tube Fitting to 1/4” MNPT, Stainless Steel
10MSC4N-S 5/8” Tube Fitting to 1/4” MNPT, Stainless Steel
5c
GAS ANALYSIS EQUIPMENT
www.apexinst.com 800-882-3214 /919-557-7300
IRM Ceramic Probe Heaters are recommended for temperatures over 500°F. (only available with 2” oversheath). Call for Pricing on Special Inconel & Ceramic Hi-Temp Heaters.
Model PC�-�S-�2 2” OD 2” OD 2” OD 1” OD
Nominal Length 4=1/4” 6=3/8” 8=1/2” 1” Classic
3’
4’
6’
8’
10’
12’
IRM 2” Stainless Steel Probe Assemblies with Stainless Steel Liner
IRM Probes are available with Stainless Steel or Inconel Sheaths, Heated or Unheated, & with 1/4, 3/8, 1/2, or 5/8 IN O.D. Liners. Additional configurations& sizes are available. CALL FOR PRICING. - -
Blank = 1”O2 = 2”
Sheath
S = Sheath
Link to Pipe Flanges
IRM System
Pre-FilterAssembly
Flange
Stainless Camlock
Heated FilterEnclosure
PolyCamlock
Heated Sample Line
Call foradditional information
6c
GAS ANALYSIS EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com
The oven can accept an 18’ long heated probe with 2” diameter sheath. The probe uses a replaceable 3/8” stainless steel liner. The oven features a lightweight construction, with a rugged strip heater, 1/2” insulation, high temperature and stainless steel hardware. Type-K thermocouple jacks are used for monitoring probe and oven temperature. A dual channel digital thermometer is recommended.
FILTER ASSEMBLIES
HEATED FILTER ASSEMBLIES
Product Description
SFA-2564 3 Port Filter Assembly, 25x64mm, Stainless Steel Filter Assembly, with One 1/4” Input, One 1/4” Output and one 1/8” FNPT Cal Gas Input Ports, Accepts GF-2564 Filter Elements
SFA-2564-2N6 6 Port Filter Assembly, 25x64mm, Stainless Steel, with total of six (6) 1/8” NPT Ports, Accepts 25X64mm Filter, Used in Tri-Sample Probe
REPLACEMENT FILTER ELEMENTSProduct Description
GF123270K Filter Cartridge, Borosilicate glass microfiber with Fluorocarbon resin binder, 12 x 32 mm, Maximum Temperature 300°F, 10/pk
GF123270S Filter Cartridge, Borosilicate Glass Microfiber with inorganic binder,12 x 32 mm, Maximum Temperature 900°F, 10/pk
GF125770K Filter Cartridge, Borosilicate Glass Microfiber with Fluorocarbon resin binder, 12 x 57 mm, Maximum Temperature 300°F, 10/pk
GF125770S Filter Cartridge, Borosilicate Glass Microfiber with inorganic binder,12 x 57 mm, Maximum Temperature 900°F, 10/pk
GF256470K Filter Cartridge, Borosilicate Glass Microfiber with Fluorocarbon resin binder, 25 X 64mm, Maximum Temperature 300°F - 10/pk,
GF256470K Filter Cartridge, Borosilicate Glass Microfiber with Fluorocarbon resin binder, 25 X 64mm, Maximum Temperature 300°F - 10/pk,
GF2517870K Filter Cartridge, Borosilicate glass microfiber with Fluorocarbon resin binder, 25 x 178 mm, Maximum Temperature 300°F, 10/pk
GF2517870S Filter Cartridge, Borosilicate Glass Microfiber with inorganic binder,25 x 178 mm, Maximum Temperature 900°F, 10/pk
Apex Instruments stocks 2 types of Cartridges: K-type with Fluorocarbon Resin Binders for Testing in Locations where Highly Reactive and/or Corrosive Gases are Present, and S-type Cartridges with Inorganic Resin Binders for Filtering Gases at Temperatures up to 900°F.
1” ProbeClamp
SFA-2564HE-A
2” ProbeClamp
Probe Clamp
SFA-2564
Product Description
SFA-2564HE-AT Thermostat Controlled Heated SFA-2564 CEM Filter Assembly and Silicone Insulated Enclosure, Accepts GF-2564 Filter Elements, 1” PC- 1 Probe Clamp, Standard Male Plug, 110V
SFA-2564HE-AV Heated SFA-2564 CEM Filter Assembly and Silicone Insulated Enclosure, Accepts GF-2564 Filter Elements, 1” PC- 1 Probe Clamp, Standard Male Plug, 240V
SFA-2564HE-B Heated SFA-2564 CEM Filter Assembly and Silicone Insulated Enclosure, Accepts GF-2564 Filter Elements, 2” Probe Clamp, Standard Male Plug, 110V. ** Cable Entry Seal sold separately **
SFA-2564HE-A Heated SFA-2564 CEM Filter Assembly & Silicone Insulated Enclosure, Accepts GF-2564 Filter Elements
REPLACEMENT FILTER COMPONENTS
7c
GAS ANALYSIS EQUIPMENT
www.apexinst.com 800-882-3214 /919-557-7300
The Apex Instruments Tri-probe allows the simultaneous sampling and monitoring from three distinct sampling points. The manifold and filter unit comes with six holes, for a unique design made for RATA sampling. The user can now extract samples without moving the probe to different traverse points. Traverse points acquire representative samples
TRI-SAMPLE PROBE
The Tri-Probe has multiple probe extension options to meet the specifications of any test site.
GAS SAMPLE FILTER HOUSINGS
SFA-116IL SFA-137G TFA-122P 760N-2
Traditional in-line gas sample filters are used to remove particulate prior to analyzing to protect your valuable equipment. Replacement filters not included.
Product Description Temperature Rating
Pressure Filters
SFA-116IL Stainless Steel, 1/4” FNPT, 3” Long 200°C (400°F) 5000 PSIG 12 x 32mm, GF123270K, GF123270S
SFA-H130S-TE Stainless Steel, Heatable, 4.57” Long, 1/4” End Ports
200°C (400°F) 30 PSIG 25 x 64mm, GF256470K, GF256470S
SFA-137G Glass Filter, T-Type, 1/4” FNPT, 4.49” Long 200°C (400°F) 150 PSIG 25 x 64mm, GF256470K, GF256470S
TFA-122P PTFE, 1/4” FNPT, 3.86” Long 150°C (300°F) 100 PSIG 12 x 57mm, GF125770K, GF125770S
760N-2 Nylon, Side Ports, 1/4” FNPT, 5.51” Long 50°C (120°F) 100 PSIG 25 x 64mm, GF256470K, GF256470S
Filter Housing
8c
GAS ANALYSIS EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com
Features• Low Cost Installation, Maintenance and Operation• Low Extractive Flow Rates, Promotes Long Filter Life• Made of Corrosion Resistant Materials• Can be used in Explosion Proof Areas• No Requirement for Heated Sample Line• No Moving Parts Anywhere in the System• Easy Dynamic In-Situ Calibration of Dilution System• Diluted Sample is Transported at Positive Pressures• Can be Used with Any Existing Ambient Air Analyzer• Manual or Optional Automatic Blow Back, Back Flushes Coarse Filter PMI-3000 Probe
SpecificationsA) Material of Construction:• The Eductor Housing, Mantle, Filter Cap and Flange (the “Wetted Parts”) are Fabricated from Inconel® 600, a Corrosion Resistant Nickel-Chromium Alloy.• The Heat Exchanger and the Four Inlet/Outlet Tubes are Fabricated from Grade 316 Stainless Steel.
B) Maximum Operating Temperature:• 750o F (400o C) with standard glass orifice.• 1,100o F (600o C) with special metal orifice – call PMI for details.
C) Dimensions:• Vacuum and Calibration lines 0.125” OD.• Dilution Air and Sample out lines 0.25” OD.• All lines supplied with 0.25” OD tube fitting attached.
ADP-007
Apex Instruments Dilution PanelFeatures• High Accuracy• High Resolution Regulation• Blow-Back Control• Calibration Circuit
aDP-007
PMI Dilution ProbePMI Dilution Probefor In-Situ Sampling Conditioning of Stack GasesThe PMI-3000 Dilution Probe performs four critical functions to prepare the sample from the stack or process, so it can be measured accurately and precisely by the analyzer. The probe uses an air driven aspirator which extracts the sample from the stack or process. It is then passed consecutively through coarse and fine particulate filters, a pre selected glass or met-al critical orifice, and finally diluted with the air from the aspirator. This process has now reduced the dew point of the sample to below that of the ambient air, preparing the sample so that it can be transported via an unheated line to the analyzer up to 300 feet away.
There are two models of the PMI-3000 Dilution Probe available, differing only in the type of mounting flange. Model PMI-3200, equivalent to the EPM 0797.302, has a 1.8” flange drilled and tapped with four mounting holes. Model PMI-3300 (equivalent to EPM 0797.303) has a threaded flange for easy use with extension tubes.
PMI-3000 / PMI-3200 / PMI-3300 Dilution Probe
Specifications:• Application EPM Thermo, PMI Type in Situ Type Probes.• Remote (Dry Contract) for Cal and Blow Back.• Sample, Bypass and Cal Gas Rotometers.
• Precision Air Pressure Regulator.• 4 U (19” W x 7”H)) Case Rack Mountable (20 lbs.)• Front Panel Air Pressure, Vacuum and Blow Back Gauge’s• 110 / 220 VAC
9c
GAS ANALYSIS EQUIPMENT
www.apexinst.com 800-882-3214 /919-557-7300
APEX Pro-Series Heated Sample Line HSLP-64-100The Apex Instruments Heated Sample Lines are designed for the professional stack tester that needs a rugged lightweight flexible sample line that can handle the abuse of IRM sampling day after day. The standard core includes one 3/8” PFA tube for the sample and one 1/4” tube for introducing calibration gas at the probe. Both lines have stainless steel over- braid and swaged tube stubs attached.
Apex Pro-Series Heated Sample Line, 100 FT, 3/8 IN & 1/4 IN PFA stainless steel Overbraid Lines, Nomex®/Aramid Felt Insulation, Non-Lead Stabilized Vinyl Elastomer Extruded Jacket (orange). Requires Temperature Controller. Apex Offers temperature controllers for use with the Pro-Series.
HslP-64-100100 FT Heated Sample Line 3/8 IN & 1/4 IN PTFE lines, Foam Insulation w/ Oversheath.
HslP-64-100
Features
• PFA Tubing with Stainless Steel Overbraid - Heated Sample; 3/8” - Unheated Cal-Gas; 1/4”
• 1/2” Nomex® Insulation
• Non-Lead Stabilized Vinyl Elastomer Extruded Orange Durable Jacket for High Visibility, Flame Retardant
• Lightweight & Flexible
• Bend Radius: 10”
• Stainless Steel Tube Stubs
Specifications• Spiral wound heating element for uniform heat distribution• Power Density 23 Watts/ft.• Supply voltage 120V or 240V• Maximum temperature rating 400o (200oC)• Tube maintenance up to 370oF (200oC) at 0oF• Type K thermocouple for control sensor• Nominal O.D. 1.75”• Weight 55 lb. for 100 ft.• Maximum operating pressure: 300 psi
A temperature controller MUST be used on this bundle in order to prevent it from overheating.
Apex offers temperature controllers for use with the Pro-Series
apex Pro-seriesDesigned for
Portable Systems
iCH-901Temperature Controller
Higher Temperature Units are Available.Inquire for Custom Lines Manufactured to your Specification.
temperature ControllerHeavy Duty (High Output) Single Station Digital Temperature Controller, 20A Max, 120V.
iCH-901
10c
GAS ANALYSIS EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com
CEM TEMPERATURE CONTROLLERS (4 different models)Apex Instruments offers a choice of one or two station Temperature Controllers in three different styles of digital display controllers. All of our temperature controllers have a panel mounted circuit breaker and a separate solid state output relay for high output reliability. The heavy duty controllers have a panel mounted circuit breaker and a separate solid state output relay for high output reliability. Our heavy duty controllers have a separate slow-blow 25 amp fuse that is panel mounted for easy access and are typically used with 50 to 100 foot heated sample lines. These temperature controllers can be used for (CEM) in any application where there is a need to control temperature. The dual station controllers can be used in configurations that require control of any two heated devices such as the probe/oven combination or the probe/heated sample line.
ICH-901
Single Station Digital Heavy Duty (High Output) Single Station Digital Temperature Controller, 20A Max, 120V.ICH-901
ICS-902
Dual Station DigitalDual Station Digital Temperature Controller, Solid State Output Relay, 10A Max, 120V.ICS-902
Single and Dual TemperatureController Features• External Vertically Mounted Aluminum Heat Sinks for Better Heat Transfer from Relays.• Compact Size: 8.5” x 7.25” x 6.5” (21.6 cm x 18.4 cm x 6.5 cm)• Oversized Solid State Relays - 25 Amp (50 Amp Available for High Output)• Type K Thermocouple Input (Other Modules Available Upon Request)• Standard Receptacles for Power Output• Alternate Connectors Available (i.e. 4-Pin Circular Connectors)
Features• Fixed or Adjustable Set Points• Four Character LED Display• Fahrenheit or Celsius Operation with Indication• Sensor Break Protection• Microprocessor Based Technology
Single Station Analog Temperature Controller with Internal Relay, 120V, Press-to-Set Digital Indicator in Diecast Aluminum Enclosure, Degree C Readout. ICS-CV1F
ICS-CV1
Product Stations Duty Controller Output Power
ICS-901 One-Station Standard Digital 15 Amps 110V
ICS-902 Two-Station Standard Digital 15 Amps 120V
ICH-901 One-Station Heavy Digital 20 Amps 120V
ICS-CV1* One-Station Standard Analog Internal Relay
120V
Temperature Controllers
*Add ‘C’ for Celsius or ‘F’ for Farenheit. Comes with press-to-set digital indicator in diecast aluminum enclosure. 240 volt operation is available for all controllers. Add “V” to end of part number. (e.g. ICS-901M-V).
Single Station Digital Temperature ControllerSingle Station Digital Temperature Controller, Solid State Output Relay, 10A Max, 110VICS-901M
Compact Rugged
ICS-901M ICS-901MFront View
Digital Display Temperature Controllers
Product Stations Duty Controller Output Power
ICS-CV1* One-Station Standard Analog Internal Relay 120V
Temperature Controllers
ICS-CV Station Digital Temperature ControllerThe Apex ICS-CV temperature controllers are basic on-off microprocessor based temperature controllers mounted in a die-cast aluminium enclosure. The temperature set-point is easily set by pushing the button and rotating the dial to the desired temperature on the LED display. Actual temperature is continuously displayed.
• Accuracy to ±0.25% of Span •1/32 DIN Controller
Single Station Analog Temperature Controller with Internal Relay, 120V, Press-to-Set Digital Indicator in Diecast Aluminum Enclosure, Degree F Readout. ICS-CV1C
11c
GAS ANALYSIS EQUIPMENT
www.apexinst.com 800-882-3214 /919-557-7300
GAS CONDITIONERS
The APEX INSTRUMENTS SGC-4000HG STIRLING GAS CONDITIONER/COOLER is specially designed for removing moisture and acid gases from flue gas samples. This new style gas chiller uses an industrial grade super efficient Free Piston Stirling Cooler (FPSC) for chilling the gas to a constant dew point. The FPSC has several advantages over the con-ventional Rankine Compressor or Thermoelectric Refrigeration units. For example, the FPSC chiller module uses a small quantity of environmentally safe helium gas as a refrigerant. The module is hermetically sealed in stainless steel casing allowing for fast and easy installation and replacement when necessary.
Specifications• Digital Temperature Control +/- 1 Degree C, LED Display• Cooling Capacity >40 Watts• Dual Path Cooling Block Anodized Aluminum• Condensate Bottle 1000 ml (Plastic Coated Glass)
• Reverse Flow Condensate Separator Silcosteels-CR Treated Stainless Steel 1” OD x 4” Active Zone• Maximum Flow Rate 2 liters per minute @ 20% H2O/Channel• Alarm Output Switched 6v DC
• Freeze Protection 80w Heater• Ambient Operating Temperature 0 to 500 C• Power Requirements 120v AC/2.5 amps
Available in Rack Mount or
Portable versions
sgC-4000HgP
• No Additional Tubing or Pumps• Digital Temperature Control• Constant Set Temperature
• Free Piston Stirling Cooler (FPSC) Has Only Two Moving Parts.• Temperature Alarm Output
Features:
The APEX INSTRUMENTS NEW SGC-4900 STIRLING GAS COOLER is spe-cifically designed for removing moisture from process gas samples prior to gas analysis. The SGC-4900 Stirling Gas Cooler uses an innovative FPSC (Free Piston Stirling Cooler). Water vapor is removed by quickly cooling the flue gas sample as it passes through two condensers in series. The first condenser is air cooled and the second condenser is actively cooled with a FPSC module. The cold finger side of the FPSC is inserted directly into the anodized aluminum, heat exchanger which surrounds the gas condenser. No piping for the environmental friendly helium refrigerate is required. Accessories Include; Condensate Pump, Heated Filters, Probe & HSL, Water Slip Sensor at Alarm, Sample Gas Pump.
sgC-4900 stirling gas Cooler
DescriptionDigital Temperature Control PID, LED Display, ± 1°CCooling Capacity Up to > 65 WattsChiller Block Anodized AluminumAir Cooled Glass Condenser with Finned Tube Heat Sink
2” O.D, 5.5” Contact Zone
Active Glass Condenser 4.5” Active ZoneFlow Rate Up to 15 LPM Dew Point 40°FFreeze Protection 80w HeaterAmbient Operating Tempera-ture
0 to 50°C (32°F to 122°F)
Inlet / Outlet Fittings 1/4” Tube UnionsPower Requirements 120VAC / 2.5 ampsDimensions and Weight 19” Rack Mount, 17” W x 16” D x 7” H, 28 lbs.
Specifications
Features:• Low Gas Absorption• Easy to Maintain• Integrated Heater• Energy Efficient• Two Stage Cooler
• Digital Temperature Control• Light Weight• High Capacity• Rack Mountable• FPSC
Moi
stur
e
% Mois ture v/s F low R ate (L P M)
0%
5%
10%
15%
20%
25%
30%
5 10 15
% H2O @ F lowR ate
Flow Rate (LPM)
Constant Dew Point Curve at 40° (4°C)
Portable unit sgC-4000 HgPsgC-4000HgP (110V)sgC-4000HgP-V (240V)
Rack mount sgC-4000HgsgC-4000Hg
12c
GAS ANALYSIS EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com
Apex Instruments Flow DrawerAFD-510The Apex AFD-510 is designed to be an easy, conve-nient, and compact way to control the flow of both stack and calibration gases.
This new panel can flow gas to either the analyzer bank(Direct calibrations) or the probe (System calibrations),and has both automatic and manual controls.
This unit has been designed with simplicity in mind.It has the same common solenoids and a simplifiedwiring protocol.
The calibration gas in use is identified by a LED along with which mode you are in and if you are sampling or calibrating. One big benefit of the Apex Instruments AFD-510 is that in sampling mode all solenoids areat “rest” which greatly extends the life of the unit.
aFD-510
Features• 11 Calibration Gas Channels (Including Zero and Span)• 5 Output or Analyzer Channels• 8 Valved Rotometers for Fine Flow Control/Adjustment 5 Analyzer Rotometers 1 Vent Rotometer 1 Probe Calibration 1 Sample Flow Rotometer• 19” Rack Mountable• Designed for Easy Maintenance and Repair• Manual or Automatic Operation
Specifications
Input Cal-Gas Channels: Flowmeters Standard: Sample 0-10 LPM Vent 0-10 LPM
Output Gas Channels: Flowmeters Available: 0-0.5 LPM 0-1.0 LPM 0-2.5 LPM 0-5.0 LPM
Voltage: 110.220 VAC, 50/60 Hz
Power: 25 Watts
Mounting Dimensions: 4U, 19” Rack Mount, 7” Height x 19” Width x 18” Depth
Weight: Approximately 24 lbs
Pressure Gauge: 0-15 psi
Connections: 1/4 Inch Stainless Steel Tube Union
AFD-510 Shown in Portable Gas Analysis Unit
AFD-510
13c
GAS ANALYSIS EQUIPMENT
www.apexinst.com 800-882-3214 /919-557-7300
AMETEK Process InstrumentsManufacturer of individual analyzers and turn-key CEM rack systems for dry-basis monitoring of pollutants in flue gases. Analyzers are available for use in new or existing extractive CEM rack systems (or other instrument racks) where the sample gas entering the analyzer is non-condensing at ambient temperatures. www.ametekpi.com.
California Analytical InstrumentsCalifornia Analytical Instruments, Inc. (CAI) provides quality gas analyzers and systems used in Industrial, Environmental, Process and Automotive Emissions applications. CAI products include Infrared Analyzers; Chemiluminescence Analyzers, Oxygen Analyzers, Flame Ionization Analyzers, UV Fluorescence Analyzers, FTIR, Integrated Systems, Specialty Products, Photoa-coustic IR Analyzers. www.gasanalyzers.com.
BUHLER TechnologiesA broad range of applications like boiler trim, emission monitoring, ammonia slip monitoring, combustion efficiency, LEL warning indication or inner atmosphere control require analyzers with different measuring principles. Bühler offers optical, paramagnetic and zirconium technologies as well as tuned diode laser (TDL) gas analyzers. www.buhler-technologies.com/gas_analysis/products/analysers.
BRAND GAUSNOx, O2 and NOx-O2 gas analyzers specifically designed for use in continuous emissions monitoring systems (CEMS) for gas turbines; designed for reliability and simple operation; with industrial interfaces for continuous visible diagnostics and intuitive calibration without the use of delicate character displays or complicated menu systems. www.brandgaus.com.
ECOMECOM America Ltd., manufactures portable emission / combustion analyzers for many applications. From single gas Oxygen and Carbon Monoxide analyzers for flue gas testing to multi-gas analyzers measuring Oxygen, Carbon Monoxide, Nitric Oxide, Nitrogen Dioxide, Sulfur Dioxide, & Hydrocarbons offered in several configurations, we have instruments for most combustion applications. Several models are approved and recognized by Regional, State, and Federal Environmental and Air quality Regulatory AgenciesECOM. www.ecomusa.com.
ENVIRONICS AnalyticsKnown for computerized gas flow instrumentation; especially gas mixing technology, based on very precise control of thermal mass flow controllers, combined with Environics computerization and calibration results in improved accuracy to +/- 1% of setpoint.www.environics.com.
14c
GAS ANALYSIS EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com
BacharachBacharach, Inc. is a world leader in the design, manufacture, and service of advanced equipment for the measurement and detection of gases and liquids. The company’s extensive product line includes instruments that detect, measure, and record combustion and environ-mental gases, temperature, relative humidity, air velocity, and other air quality and safety parameters. A full line of refrigerant recovery equip-ment for residential, industrial, and automotive applications further extends Bacharach’s family of products. www.bacharach-inc.com.
NovaNova Analytical Systems Inc. has been designing and manu-facturing dependable gas analysis equipment for over 30 years. Nova offers portable gas analyzers, continuous gas analyzers and sample conditioning equipment for industrial applications. Nova’s integrated approach to design and manufacturing al-lows us to configure our products to suit each application, while still being able to offer the best price, long-term reliability and proven technology in each analyzer. www.nova-gas.com.
TELEDYNE INSTRUMENTS (API)TAPI offers products for continuous emissions monitoring, including: Ultraviolet Absorption Analyzers, Paramagnetic Analyzers,Infrared Gas Filter Correlation Analyzers, Nondis-persive Infrared (NDIR) Analyzers, Ultraviolet Fluorescence Analyzers, Chemiluminescence Analyzers.www.teledyne-api.com/overview.asp.
VIG INDUSTRIESOffers microprocessor controlled hydrocarbon analyz-ers; Dual or Single Channel (FID) flame ionization detector based (GC) gas chromatography, (VOC) volatile organic compounds, and (THC) total hydro-carbon analyzer systems. www.vigindustries.com/products.htm.
SERVOMExKnown for paramagnetic sensing technology and the development of zirconia, photometric, thick film and plasma technologies. The result is high-performance, cost-effective gas analysis, delivered through a portfolio of dependable products ranging from portable gas anal-ysers to complex process solutions. www.servomex.com/servomex/web/web.nsf/en/servopro-1440.
15c
GAS ANALYSIS EQUIPMENT
www.apexinst.com 800-882-3214 /919-557-7300
Burrell Oxsorbent solution for determining oxygen in gas analysis, 8 oz bottles.
B39-710
Burrell Cosorbent, solution for determining Carbon Monoxide in gas analysis, 8 oz bottles.
B39-720
Burrell Disorbent solution for determining Carbon Dioxide in gas analysis, 16 oz, bottles.
B39-730
METHOD 3 ORSAT ANALYZER
Model Description
OG-1V/18 Burette, with 3-way Valve and Water Jacket, PTFE Valve Body, 100 mL, Scale 0-30% x .01
OG-2 Aspirator Bottle
OG-5V Contact Pipette, Valved, Insert Only
OG-5B Pipette Bottle with Hose Barb
GA-18C Solid Cap with #18 Threads and Seal
GA-30B Bored Cap with #30 Threads, 22 mm ID
GA-30S Silicone Seal Ring #30 Threads, 22 mm ID
TB-3V-P Tedlar® Bag,Three Compartment with three Poly Valves
TR-5/3 Black Rubber Tubing, 5/16” OD x 3/16” ID, per foot
VC2-50 VersaCase Clamp, 50 mm with Knurled Brass Thumb nuts
VSB3 VersaCase 3, with Hinged, Removable Doors and Mounting Rail
VSB2-MP VersaCase Mounting Plate
Orsat Accessories
Squeeze Bulb PumpThe heavy wall rubber Squeeze Bulb Pump with stainless steel valves and connections can be used for gas sampling, pressure source for calibrations and leak tests, and for conditioning probes and sample lines.
a-350
Method 3 determines CO2 and O2 concentrations and dry molecular weight of a sample from an effluent gas stream. The gas sample is analyzed for CO2 and O2 on a gas absorbtion basis, results are expressed in precentage units. For dry molecular weight determination, either an Orsat or a Fyrite analyzer may be used for the calculations.
The Orsat Analyzer Train is designed specifically for Method 3, for analysis of integrated or grab bag samples collected in Tedlar® bags. A liquid filled leveling bottle moves the integrated sample through a graduated glass burette and absorption pipettes containing absorbing reagents. The result-ing changes in volume measure percent of O2 , CO2 and CO. The burette is water jacketed for temperature stability.
VsC-33
Replacement Fluids
Domestic Delivery only. Sold by case (12 bottles per case). Drop shipped by vendor due to Hazardous Classification.
Packing List
VSB3
16c
GAS ANALYSIS EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com
COMBUSTION GAS ANALYZERS
Model Descritption
B10-5000 CO2 Fyrite® Gas Analyzer, Range 0-20%
B10-5032 CO2 Fyrite® Gas Analyzer, Range 0-60%
USA KitsCO2 Testing
Model Descritption
B10-5001 CO2 Fyrite® Gas Analyzer, Range 0-20%
Export Single Kits CO2 Testing
Model Descritption
B10-5020 CO2 & O2 Fyrite® Gas Analyzer, CO2 Range 0-20%, O2 Range 0-21%
B10-5021 CO2 & O2 Fyrite® Gas Analyzer for Export, CO2 Range 0-20%, O2 Range 0-21%- EXPORT ONLY.
Duplex Kits
Model Descritption
B10-5011 O2 Fyrite® Gas Analyzer, Range 0-21%
B10-5046 O2 Fyrite® Gas Analyzer, Range 0-60%
O2 TESTING
Model Descritption
B10-5012 O2 Fyrite® Gas Analyzer, Range 0-21%
O2 TESTING
Model Descritption
B11-7052 CO2 Fyrite® Gas Analyzer Repair Kit, Range 0-20% + 60%
B11-7054 O2 Fyrite® Gas Analyzer Repair Kit, Range 0-20% + 60%
Repair KitsIncludes a bottle of Fyrite® fluid, valve plunger gasket, top gasket, screws, diagram and envelope of filtering material.
FYRITE® GAS ANALYZERS
Fyrite® CO2
Fyrite® Gas Analyzers are fast, accurate and easy to use instruments for measuring and analyzing carbon dioxide or oxygen. Fyrite® Analyzers are available for either CO2 or O2 analysis. Fyrite® Indicators have a broad range; they may be exposed to ambient temperatures from -34° to 65°C (-30° to 150°F), and gases up to 450°C (850°F) may be tested with standard aspirator sampling equipment. Single analyzers and additional ranges are available along with refill and repair kits. Call for details.
Model Descritption
B11-7047 CO2 Fyrite® Gas Analyzer Refill Kit, Range 0-20% + 60%
B11-7050 O2 Fyrite® Gas Analyzer Refill Kit, Range 0-21% + 60%
Refill KitsIncludes two Bottles of Fyrite® Fluid, top gasket, screws and envelope of filtering material.
Model Descritption
B10-5057 CO2 Fyrite® Fluid , Range 0-20% + 60%, 3 (2oz.) Bottles per Case
B10-5060 O2 Fyrite® Fluid , Range 0-20% + 60%, 3 (2oz.) Bottles per Case
Fluids
For more information on Bacharach Products visit: www.bacharach-inc.com
17c
GAS ANALYSIS EQUIPMENT
www.apexinst.com 800-882-3214 /919-557-7300
GAS SAMPLE FILTER HOUSINGS
SFA-116IL SFA-137G TFA-122P 760N-2
GAS SAMPLE FILTER ELEMENTSApex Instruments stocks two types of Borosilicate Glass Microfiber Cartridges to accomodate all particulate removal needs. For testing in locations where highly reactive and/or corrosive gases are present Apex offers the K-Type High Temperature with Fluorocarbon Resin Binders. The S-Type has low temperature cartridges with Inorganic Resin binders for filtering gases at temperatures up to 480°C (900°F).
Product Description: 10 per pack
GF123270K 12 mm x 32 mm, maximum temperature of 150°C (300°F)
GF125770K 25 mm x 57 mm, maximum temperature of150°C (300°F)
GF256470K 25 mm x 64 mm, maximum temperature of 150°C (300°F)
GF2517870K 25 mm x 178 mm, maximum temperature of 150°C (300°F)
GF123270S 12 mm x 32 mm, maximum temperature of 480°C (900°F)
GF125770S 12 mm x 57 mm, maximum temperature of 480°C (900°F)
GF256470S 25 mm x 64 mm, maximum temperature of 480°C (900°F)
GAS SAMPLE FILTER ELEMENTS
Traditional in-line gas sample filters are used to remove particulate prior to analyzing to protect your valuable equipment. Replacement filters not included.
Product Description Temperature Rating Pressure Filters
SFA-116IL Stainless Steel, 1/4” FNPT, 3” Long. 200°C (400°F) 5000 PSIG 12 x 32mm, GF123270K, GF123270S
SFA-H130S-TE Stainless Steel, Heatable, 4.57” Long, 1/4” End Ports.
200°C (400°F) 30 PSIG 25 x 64mm, GF256470K, GF256470S
SFA-137G Glass Filter, T-Type, 1/4” FNPT, 4.49” Long. 200°C (400°F) 150 PSIG 25 x 64mm, GF256470K, GF256470S
TFA-122P PTFE, 1/4” FNPT, 3.86” Long. 150°C (300°F) 100 PSIG 12 x 57mm, GF125770K, GF125770S
760N-2 Nylon, Side Ports, 1/4” FNPT, 5.51” Long. 50°C (120°F) 100 PSIG 25 x 64mm, GF256470K, GF256470S
Filter Housing
OMNIFLOW FILTER HOLDERSThe Multi-Port Stainless Steel Filter Assembly has a 200°C (400°F) rating and is typically used for the filtering of combustion gases prior to analysis. The OmniFlow Filter Holder (N6) is spring loaded and designed for positive sealing. It features 6 ports (3 sample inlets, 1 calibration, 1 pressure and 1 sample exit). Each port is 1/4” FNPT (accepts 25” x 64” filters). Cable entry seals sold separately.
Three 1/4” Port Stainless Steel Filter AssemblyAccepts 25 mm x 64 mm filter.
sFa-2564-V2
SFA-2564-V2SFA-2564-4N6
Six Port Stainless Steel Filter AssemblyAccepts 25 mm x 64 mm Filter.
sFa-2564-4n6
Product Description
GF123270K Filter Cartridge, Borosilicate Glass Microfiber with Fluorocarbon Resin Binder, 12 x 32mm, Maximum Temperature 300°F, 10/pk.
GF123270S Filter Cartridge, Borosilicate Glass Microfiber with Inorganic Binder, 12 x 32mm, Maximum Temperature 900°F, 10/pk.
GF256470K Filter Cartridge, Borosilicate Glass Microfiber with Fluorocarbon Resin Binder, 25 x 64mm, Maximum Temperature 300°F - 10/pk.
FiltersProduct Description
GF256470S Filter Cartridge, Borosilicate Glass Microfiber with Inorganic Binder, 25 x 64mm, Maximum Temperature 900°F, 10/pk.
GF125770K Filter Cartridge, Borosilicate Glass Microfiber with Fluorocarbon Resin Binder, 12 x 57mm, Maximum Temperature 300°F, 10/pk.
GF125770S Filter Cartridge, Borosilicate Glass Microfiber with Inorganic Binder, 12 x 57mm, Maximum Temperature 900°F, 10/pk.
18c
GAS ANALYSIS EQUIPMENT
800-882-3214 /919-557-7300 www.apexinst.com
CONDENSERS
SC-9A SC-9A
SC-9U
Inlet
Apex Instruments Stainless Steel Condensers are designed to be submerged in an ice-water bath for condensing and removing water vapor prior to analysis. Use in conjunction with the peristaltic pump (see recommended pump below) to continuously remove the condensate. Condensers are recommended to be used in a series of two or more. Custom-made condensers available please call for details on water jacketed condensers, chillers and appropriate pumps.Stainless steel condenser assembly with vessel, cap with Inner tube, clamp and gasket. Two 3/8” Ports and 1/4” drain tube.sC-9a
Adapter, 3/8” button hook adapter for connecting condenser in series. sC-9u
Borosilicate Glass CondensersApex Instruments offers two types of borosilicate glass condensers. The products include caps and seals.
The Double-Headed Single-Speed Peristaltic Pump (PP927-049) is ideal for removal of condensate from glass and stainless steel condens-ers. Each head provides a flow rate of 98cc/min. and can be used for two independent uses or combined when needed to increase the flow rate or pressure capability. Additional peristaltic pumps are available.
PP927-049
Single speed, dual head peristaltic pump, 49 rev/min, flow rate 98 ml/min per head.
PERISTALTIC PUMP
Product DescriptionVGC-9 Glass Condenser-9” x 2” OD, 3/8” tube unions for inlet & outlet, 1/4” drain tube. NO SEALS.
VGC-12 Glass Condenser-12” x 2” OD, 3/8” tube unions for inlet & outlet, 1/4” drain tube, water jacket. NO SEALS.
VGC-12M Glass Condenser-12” x 2” OD, with GL-18 threads for inlet, outlet & drain, threads accept 1/4” or 3/8” with proper seal, water jacket.
VGC-12MA Glass Condenser-12” x 2” OD, with GL-18 threads for inlet, outlet & drain, threads accept 1/4” or 3/8” with proper seal, water jacket w/caps & seals.
The VGA-12A Condenser allows the flow of ice water around the sample stream. Glass condenser with 3/8” tube unions for inlet and outlet, 1/4” drain on bottom, water jacket, 2” OD, 12” height.VgC-12a
The VGA-9A Condenser is designed to be submerged in an ice-water bath for condensing water vapor. Glass condenser, coaxial design with 3/8” tube unions for inlet and outlet, 1/4” drain tube, 2” OD, 9” height.VgC-9a
VGC-12AVGC-9A
19c
GAS ANALYSIS EQUIPMENT
www.apexinst.com 800-882-3214 /919-557-7300
Gas Analysis Equipment
Apex Dilution Panel .................................... 8cApex Flow Draw ......................................... 12cCombustion Gas Analyzers ........................ 16cCondensers ................................................ 18cCondensers, Borosilicate Glass ................. 18cFilter Assemblies ........................................ 6cFilter Holders .............................................. 6cGas Sample Filter Elements ....................... 6cGas Conditioners ........................................ 11cGas Analyzers ............................................ 13c-14cGas Sample Filter Housing......................... 17cGas Sample Filter Elements ....................... 17cIRM, Transportable IRM System ................ 3c
Method 3, Orsat Analyzer ........................... 15cPMI Dilution Probe...................................... 8c Pre-Filters ................................................... 4cPro-Series Heated Sample Line ................. 9cProbe, Assemblies ...................................... 5cProbe, CEM ................................................ 5cProbe, IRM ................................................. 4cProbe, IRM Ceramic Heater ....................... 5cProbe, Stainless Steel Liners ..................... 5cPumps, Peristaltic ....................................... 18cTemperature Controllers ............................. 10c Tri-Sample Probe ....................................... 7c
www.apexinst.com
919-557-7300 or 800-882-3214Fax: 919-557-7110
Website: www.apexinst.comContact: [email protected]
Apex Instruments, Inc.204 Technology Park Lane
Fuquay-Varina, N.C. 27526, U.S.A.
Accessories cAtAlog
Software
Tubing & Filters
Balances
37d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
Delivery:Most orders are shipped within 24 hours of receipt. Please allow extra time for custom orders. Shipping times vary according to the requested shipping service. If you have questions about your shipment please email our shipping management at [email protected].
Return Merchandise AuthorizationCustomers wishing to return items for service or credit need to contact our sales associates for an RMA. Contact by email at [email protected] or by phone (919) 557-7300 or toll free (800) 882-3214.
PricingPrices are published for U.S. customers only. International customers should contact their local distributor. Prices are in U.S. Dollars, FOB shipping point, or Ex Works for International orders. Please confirm current prices by phone, fax or email. Please refer to our price list for a complete list of part numbers and kit configurations.
PaymentFor your convenience, MasterCard, VISA and American Express arewelcome. Company purchase orders are accepted upon credit approval.
We back up this commitment with extensive knowledge of our products, good communication and an excellent customer service history. Our equipment isdesigned by experienced stack testers who know what you face when performing compliance testing.
We encourage you to suggest ideas to improve our equipment. We work closely with you, over the long term, to provide the best equipment for your needs.
CUSTOMER SATISFACTION is guaranteed at APEX INSTRUMENTS.
Hours of Operation:Monday through Friday from 8:00 am
until 5:00 p.m. (EST).
Apex Instruments, Inc. 204 Technology Park Lane
Fuquay-Varina, NC 27526 USA
In U.S. Call Toll Free:1-800-882-3214
Local: 1-919-557-7300fax: 1-919-557-7110
e-mail: [email protected]
www.apexinst.com
Doug Bernhardt Customer Service
Please feel free to call our friendly sales staff today!
Vance JonesDomestic Sales,
Customer [email protected]
Janet NicholsSales Manager
John StauberInternational [email protected]
ACCESSORIES
FLOW, PRESSURE & TEMPERATURE
MERCURY AND gAS SAMPLINg SYSTEMS & EQUIPMENT
gAS ANALYSIS EQUIPMENT
APPENDIX
INDEX
ISOKINETIC SAMPLINg EQUIPMENT
Phone: 919-557-7300 or In the U.S. 800-882-3214Monday-Friday, 8:00 a.m. to 5:00 p.m. (Eastern Time)
Fax: Order at your convenience 24 hours a day, 7 days a week 919-557-7110
Website: www.apexinst.com
Please visit our website for additional product information, new product releases, updated materials, manuals, reference data and valuable links.
Solutions for Source Sampling Equipment
Apex Instruments is a world leader in the manufacture, design and distribution of source sampling equipment. We are located approximately 20 miles from the United States Environmental Protection Agency (U.S. EPA) in Research Triangle Park, North Carolina. Our equipment complies with emissions measurement standards for stationary combustion sources in accordance with EPA guidelines. Depend on Apex Instruments to provide you with the proper, well-engineered equipment for consistent, accurate and reliable results.
TECHNICAL SERVICESApex Instruments understands the needs and high demands of the individuals working in the source sampling industry. Government agencies, consulting firms and private industries throughout North America and 50 countries around the globe, are the primary users of our equipment. Our knowledgeable staff includes skilled industry professionals, stack testers and chemists. They can help you make important decisions regarding your specific application needs.
CUSTOM FABRICATION & ASSEMBLYApex Instruments’ custom-designed facility was built in 2005. We design, build and expedite all equipment orders quickly through our in-house engineering, production and welding departments. We continue our steady commitment to quality in compliance testing by consistently designing and developing reliable source sampling equipment. We follow guidelines set by U.S. EPA Reference Methods and always keep the genuine needs of the stack samplers in mind.
CALIBRATION SERVICESApex Instruments offers dedicated, climate-controlled, precision calibration services for a variety of measuring instruments to keep your gas meter, orifice and pitot tube calibrations up-to-date. Our trained staff utilizes reliable calibration equipment and tools like the NIST Certified Bell Prover, wet test meters, electronic flow calibrators and wind tunnels. We offer a certificate of calibration when requested.
AWARDSApex Instruments received the Safety and Health Achievement Award (SHARP) from the North Carolina Department of Labor. The program recognizes small to medium size businesses that establish and maintain effective safety standards and health programs. We were also ranked in the top 500 by Inc. Magazine as being one of the fastest growing privately held companies.
ACCESSORIES
Mercury Replacement Parts, XC-522 / XC572 Components ...............................................3d - 10d Filter Media .................................................11d - 12d Sample Recovery, Bottles ......................13d - 14dPFA Components and Fittings ...............15d Balances ...................................................16d - 17d
Desiccator and Desiccants ........................18dSilica Gel, Drierite® Desiccants Dew-Point Meters .......................................19dCam-Lock, FlangesPort Adapters & Packing Glands ..........20d - 21d Meter Calibration ........................................22d
Calibration Equipment & Services ........22d - 23dOrifice Flow Meters, Flow Meters ..............................................24dInclinometers ............................................25d
Tubing, Dry Gas Meters,Electrical / Electronic Parts ....................26d - 27dStainless Steel Fittings, Quick Connects .......................................28d - 29dPumps & Accessories, Equipment Cases ....................................30d- 31dMonorails, Manuals & Reference Materials ............................32d - 34dIsokinetic Calculator& Spread Sheet, Software .....................35dAccessories Index ...................................36d
3d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
MERCURY SPARE AND REPLACEMENT PARTS
Model DescriptionM-PCB-DACV3A Populated Printed Circuit Board for Data Acquisition and Control (DAC) for XC-6000EPC, Dual PC-Based Hg ConsolePCB-TC/MUX Populated TC/Mux Board for Use in XC-6000EPC Mercury Console, 8 Type K TC Channels with External Signal
and Moisture Analyzer InputsPCB-LED-HG Board, LED DisplayEL-PCB-MODBUS-1 Board, TCP/IP Modbus InterfaceEL-CAT55FT Cable, Ethernet CAT 5.5 FT (blue)EL-SDCARD A-DATA Speedy 1GB Secure Digital (SD) Flash Card Model SDC-1G0EL-EBR-2310 D-Link Router, IEEE 802.3/3u, IEEE 802.11b/g Wireless-G Broadband Router, Used in Meter Consoles in Storm
Case Enclosure onlyEL-WBR-1310 D-Link Router, WBR-1310 Router - 54Mbps, 802.11g, 4-Port, Used in Meter Consoles in SKB, Environmental EnclosuresGP-C131-11 Pump, BTC Diaphragm Pump, Brushless Motor, 10,000 HR, Max Vacuum 20”HG, 12VDC, 3900 RPM, Max PSIG 24”GP-D737B-2201 Pump Diaphragm Hargrave Replacement Pump for XC-30B and XC-260 Meter ConsolesDGM-AP25-5701 Dry Gas Meter w 5701 Optical Encoder, Metric, Model AP25 with Bushings and FittingsDGM-AP25K Replacement Kit for DGM-AP25-5701 with Optical Encoder & Adapter Plate for Use in Replacing DGM-SK25-5701DGM-APADPT Adapter Plate Kit for DGM-AP25-5701DGMC-3A-LF Pre-test 3 Point Low-Flow (less than 1Lpm) Calibration for Apex Meter Console. 900, 600, 300 ccm TOT4-36X72 Quadrature Pulse Digital Totalizer 36 X 72 DINAK-6000 Deluxe Mercury Audit Kit for Appendix K/Method 30B System Includes: SK25 DGM with 15-pt Calibration, Quadrature
Totalizer, Vaccum Gauge, 4U Black Polyethylene Molded Case, Handheld Type K Thermocouple Simulator with Certificate, Hand-Held Digital Barometer, Digital Thermometer, Vacuum Bottle
QC-ADAPTER-1/4” 1/4” Quick Connect Mercury Audit Kit AdapterEL-670-OA938 AC Fan, 92mm ,115VAC, 50CFMMA4-20SIM Simulator,4-20mA, with Enclosure, Connector, Power Switch, & PotentiometerAWM-4360 Airflow Sensor, Signal Conditioning: Amplified; Flow/Pressure Range: + 6000 sccm (6.0 SLPM); Linear Range 1LPM; Port
Style: Manifold, (Flow Controller)XC-6K-PGMC Programming Cable for XC-6000EPC Automated Mercury Sorbent Trap Metering ConsoleM-AM2312 Valve, 3-Way, .055/.048 Orifice, 12V VSO-1SV Valve, Solenoid, Proportional. Model VSONC-3S11-IC-FO Manifold Mount with Wire Leads and 11.5VDCSP-PSE541-M5 Sensor, Pressure, 0-30” Hg, 1 NPN/PNP Open Collector Transistor Output, 30VDC, 125mA
BARO-A-4V Barometric Pressure Sensor, 600 to 1100 mbar, Temperature Compensated, Amplified OutputM-CBR10A-M Electrical Breaker, 10A, Panel Mount Magnetic Type Circuit Breaker Rocker Switch, 10 Amp. Horizontal Mount.
Typically Used in 120V Consoles as Probe/Oven Breaker SwitchM-CB15A-M Electrical Breaker, 15A, Panel Mount Magnetic Type Circuit Breaker, 15 Amp. Typically Used in 120V Consoles
as Main BreakerD-60A Power Supply, 5V@6A, 12V@4AEL-P1082-031 Connector, A TO B USB, Panel MountEL-TL5242W Memory Backup Lithium Batteries 3.6V 2.1Ah Battery PackPCB-BATTERY Battery Interface Board with Short-Term Capacitor Backup for Use with XC-6000 DAC BoardTC-PJK ThermoCouple Jack, Type K, Panel, Snap-InAM-T3107000 C16-1 Series Amphenol Circular Connector. High Grade Plastic for Harsh Environmental Conditions.
Panel Mount Straight Female Slots, 7 Slot (6 + Ground (First Mate/Last Break)AM-T3108 C16 Amphenol Circular Connector, 4 Pin (Cable Straight Male), Probe / Trap Heater Power Connection, Console SideAM-T3109 C16-1 Amphenol Circular Connector, 4 Socket (Cable Straight Female), Probe / Trap Heater Power Connection, Probe SideXC-6K-MANI Manifold Subassy, XC-6000EPC - Service Replacement Manifold Subassembly Includes Vacuum Sensor,
Mass-Flow Sensor, 2-Way Manifold Valve, Proportional Valve, Stainless Steel Hose Barb Fitting. AssemblyCalibration Data to be Provided with this Unit.
DIF-N70 Disposable In-Line Filter, Nylon Housing with 1/4” Tube Stubs, 95%+ Efficiency for 0.1 Micron
CONSOLE REPLACEMENT AND SPARE PARTS
4d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
CONSOLE
M-PCB-DACV3A
EL-PCB-MODBUS-1
EL-WBR-1310
TOT4-36X72Quadrature Pulse Digital Totalizer36 X 72 DIN.
Populated Printed Circuit Board for Data Acquisition and Control (DAC) for XC-6000EPC, Dual PC-Based Hg Console.
PCB-LED-HgBoard, LED Display.Board, TCP/IP Modbus Interface.
EL-EBR-2310D-Link Router, IEEE 802.3/3u, 11b/g Wireless-G Broadband Router, Usedin Meter Consoles in Storm CaseEnclosure only.
D-Link Router, WBR-1310 Router - 54Mbps, 802.11g, 4-Port, Used in Meter Consoles in SKB, Environmental Enclosures.
DgM-AP25-5701
DgM-APADPTAdapter Plate Kit for DGM-AP25-5701.
Dry Gas Meter w 5701 Optical Encoder, Metric, Model AP25 with Bushings and Fittings.
$404.00
PCB-TC/MUX
EL-SDCARD
Populated TC/Mux Board for Use inXC-6000EPC Mercury Console, 8 Type K TC Channels with External Signal and Moisture Analyzer Inputs.
A-DATA Speedy 1GB Secure Digital (SD) Flash Card Model SDC-1G0.
gP-C131-11Pump, BTC Diaphragm Pump, Brushless Motor, 10,000 HR, Max Vacuum 20”HG, 12VDC, 3900 RPM, Max PSIG 24” for XC-6000EPC.
DIF-N70Disposable In-Line Filter, Nylon Housing with 1/4” tube stubs, 95%+ Efficiency for 0.1 Micron.
gP-D737B-2201Pump Diaphragm Hargrave Replacement Pump for XC-30B and XC-260 Meter Consoles.
Adapter Plate Sold Separately.
5d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
CONSOLE
AK-6000 Audit KitDeluxe Mercury Audit Kit for Appendix K/Method 30B System Includes: AP25 DGM with 15-pt Calibration, Quadrature Totalizer, Vaccum Gauge, 4U Black Poly-ethylene Molded Case, Handheld Type K Thermocouple Simulator with Certificate, Hand-Held Digital Barometer, Digital Thermometer, Vacuum Bottle.
XC-6K-PgMCProgramming Cable for XC-6000EPC Automated Mercury Sorbent Trap Metering Console.
Magnetic Type Circuit Breaker Rocker Switch,10 Amp. Horizontal Mount. Typically Used in 120V Consoles as Probe/Oven Breaker Switch.
EL-TL5242WMemory Backup Lithium Batteries 3.6V 2.1AhBattery Pack.
VSO-1SVValve, Solenoid,ProportionalModel VSONC-3S11-IC-FO Manifold Mount with Wire Leads and 11.5VDC.
EL-670-OA938AC Fan 92mm 115VAC 50CFM.
AWM-4360Airflow Sensor, Signal Conditioning: Amplified; Flow/Pressure Range: + 6000 sccm (6.0 SLPM); Linear Range 1LPM; Port Style: Manifold.
M-AM2312Valve, 3-WAY, .055/.048 Orifice, 12V.
Kit Includes: Secondary Reference MeterDGM-AP25SRD
Thermocouple SimulatorM5C-520
Handheld Digital BarometerBAR-4198
36” Thermocouple Type KTCA-36HG
6” Thermocouple Y AdapterTCA-6YHG
Handheld WaterproofThermometerDPT-168-NIST
Insulated Ice BathAK-6TH16
DgM-AP25SRD
M5C-520 BAR-4198
DPT-168-NIST
TCA-36Hg
TCA-6YHgAK-6TH16
M-CBR10A-MM-CBR15A-M
6d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
CONSOLE
26809 AM-SP100A M-SD31
Battery Interface Board with Short-Term Capacitor Backup.
Thermocouple Jack, Type K, Panel, Snap-In.
Mounting Clip for Aluma-Sorb Cartridge. Fan, for Stirling Chiller, 115V, Mechatronics. Temperature Controller, Red LED, Watlow.
BARO-A-4VBarometric Pressure Sensor, 600 to 1100 mbar, Temperature Compensated, Amplified Output.
EL-P1082-031Connector, A to B USB, Panel Mount.
SP-PSE541-M5Sensor, Pressure, 0-30” Hg, 1 NPN/PNP Open Collector Transistor Output, 30VDC, 125mA.
TC-PJKPCB-BATTERY
AH-610-AHousing, Adsorption, Assembly with 1/4” Fittings and Filled with Aluma-Sorb.
COOLER
M-PSRS7512Power Supply, 75W, 12V, 6 AMP, Input: 100-240VAC.
D-60APower Supply 5V@6A, 12V@ 4A, Meanwell.
M-PCB-REg-ARegulator PCB Assembly 5V, for Use with M-PSRS7512.
COOLER COOLER
COOLERCOOLER COOLER
7d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
CONSOLE AND COOLER
AM-T3109C16-1 Amphenol Circular Connector, 4 Socket (Cable Straight Female), Probe / Trap Heater Power Connection, Probe Side.
AM-T3108C16 Amphenol Circular Connector, 4 Pin (Cable Straight Male), Probe / Trap Heater Power Connection, Console Side.
HgH-2T144WReplacement Probe Heater, 2-ft, 575 Watt. (used on all probes, exit end of probe).
PROBE
HgH-4T463WReplacement Probe Heater, 4-ft, 463 Watt.
HgH-5T1650WReplacement Probe Heater, 5-ft, 1650 Watt.
HgH-STRI72Replacement Probe Heater, 6-ft, 2000 Watt.
SSR-330-25Relay, SSRT, 25A 110/240V.
XC-6K-MANIManifold Subassy, XC-6000EPC - ServiceReplacement Manifold Subassembly IncludesVacuum Sensor, Mass-Flow Sensor, 2-WayManifold Valve, Proportional Valve, StainlessSteel Hose Barb Fittings.
HgH-9T838WReplacement Probe Heater, 9-ft, 838W.
HgH-12T1000WReplacement Probe Heater, 12-ft, 1000W.
AM-T3107000C16-1 Series Amphenol Circular Connector.High Grade Plastic for Harsh EnvironmentalConditions. Panel-Mount Straight Female Slots,7 Slot (6 + Ground (First Mate/Last Break).
HEATED UMBILICAL / SAMPLE LINE
PROBE PROBE
COOLER
8d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
HGP-SHIELD-S-EXT-6HGP-SHIELD-C-EXT-6
HGP-STASmall Trap (6mm) Adapter for Mercury Probes. Includes 10MTUR6M-S (with 10mm Nut and ferrule) and Three 1/4” Ceramic Ferrules.
SGC-J10-30B10-Ft Jumper, For Use with Portable Hg System, Gas Conditioner and Portable Hg Console.
ALUMA-SORBActivated Alumina Dessicant, Highly Efficient Adsorbent with High Porosity and Contact Surface. 1/8” Diameter Beads, 2.5Kg (5.5 LB) Container with 80% Active Alumina (>/= 92%) and 20% Silica Gel.
GA-GL-45SSeal for 1000 ml Bottle.
QC-PMC2QC, Stirling Gas Conditioner, Male, Straight Connector, 1/4” O.D. PTF,1/8” O.D. X.170” I.D. (Used on DrieriteCartridge Outlet/Top) – Threaded Male.
QC-SGC-M2QC, Stirling Gas Conditioner, Straight Connector, Ferruless Polytube Fitting, PTF, 1/4” O.D. X.170” I.D. (Heated U-Cord Sample Line to Stirling, High-SO2 Connector) – Tube-Mount Male.
QC-SGC-F4QC, Stirling Gas Conditioner, Female,Coupling Body 1/4” O.D. (Used on Stirling Cooler Sample in Connection).
PROBE
Thermocouple Plug Assembly, Mini,Type K, Male.
TC-SP-KA
SGC-J55-Ft Jumper, For Use in 18U Hg System. For Use with Rack Mount Gas Conditioner in 18U Cabinet.
SGC-J10-6K10-Ft Jumper for Use with Portable Gas Conditioner and Portable Model XC-6000 Hg Meter Console.
Mercury Sorbent Trap Shields HGP-SHIELD-S-EXT ShieldsStainless Steel Trap Shield Available in 6” Long x 2” O.D. Diameter. Recommended for short sampling runs, such as those required by Method 30B.
HGP-SHIELD-C-EXT ShieldsC276 Alloy Trap Shield Available in 6” Long x 2” O.D. Diameter. Recommended for corrosive environments and long continuous sampling runs (5 to 7 days).
9d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
10M-F-TgFerrule, 10MM, Single, Glass Filled Teflon.
10 M-F-Tg-DZ
PROBE
10MMNU-SNut, 10MM Tube, Stainless Steel.
10MMNU-S-EXTParticulate Shield for 10MM Sorbent Trap Stainless Steel Tube, 3/4” O.D. x 1.25” L with 10mm Nut, Welded.
10MMNU-C-EXTParticulate Shield for 10MM Sorbent Trap, C276 Hastelloy C276 Tube, 3/4” O.D. x 1.25” L with 10mm Nut, Welded.
4NU-SNut, 1/4 Tube, Stainless Steel.
SR-2.625Neoprene Square Ring, 2” I.D. x 2-5/8” O.D. x 3/16” T.K., for Cam-Lock Connectors.
gSB-500SC
SPARES / CONSUMABLE
Sample Bottle, Clear Glass, GL-45 Threaded, 500mL Safety Coated, for Condensate Collec-tion, Used in 16U Shock Mount Rack Chiller.
gSB-250SCBottle, Sample, Clear Glass, GL-45 Threaded, 250mL with Safety Coat Sample Bottle, 250mL, Used in SC-40 Con-densate Collection Ice Bath.
gSB-1000SCSample Bottle, Clear Glass,GL-45 Threaded,1000mL Safety Coated,for Condensate Collection.
gSB-1000SCASample Bottle, Assembled, Clear Glass,GL-45 Threaded,1000mL Safety Coated,for Condensate Collection.Assembly includes GA-GL-45B, GA-GL-45S.
10d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
XC-522 and XC-572 Components ListPart Number Description TC-765KF Display, TC, PNI, LED, 120/220V M-SD31 Controller, Temp, Red LED, Watlow MC-T Timer, MC, Veeder-Root M-SCKT15A Conn, Pwr, IEC Inlet 15A/250V M-49BK Recept, EL, Snap-In, Term M-31302A Switch, TC. 7 Channel TC-PJK TC Jack, Type K, PNL, Snap-In QC-BHF8-SS QC, Blkhd, 1/2IN-1/2TU, F, SS QC-BHF4-SS QC, Blkhd, 1/4IN-1/4TU, F, SS QC-BHF6-SS QC, Blkhd, 3/8IN-3/8TU, F, SS QC-BHM6-SS QC, Blkhd, 3/8IN-3/8TU, M, SS B2VH-6S Valve, Ball, 3/8TU, SS, PNL, Nut NV3HA-6S Valve, Needle, Angle, 3/8T-3/8T, S DGM-110 Meter, Dry Gas, 110 Rockwell G301U Gage, Vac, 0-30HG, 1.5IN, PNL M-42210 Manometer, Dual, PNL, 0-10” H2 QC-MAN-F3 QC-Manometer, F-1/8MNPT, S
1234567891011121314151617
Part Number Description QC-MAN-M2 QC-Manometer, M-1/4HB, Delrin XC-10U Black RotoRack Shallow Case M-RA911 Switch, Curvette, EC Comp., I-O AM-MCP Replacement Meter Console Wired Amphenol Sub-Assembly M-422B Bracket, Manometer, Adjust, Stainless Steel M-422DS Manometer Displacer Knob L-441160 Latch, Panel, Screw, Large, Sou 3439T12 Webbing, 2”, Black Nylon M-CBR5A-M Magnetic Type Circuit Breaker Rocker Switch, 5 Amp., 120V M-CBR3A-M Magnetic Type Circuit Breaker Rocker Switch, 3 Amp., 240V
18192021
22
23242526
27
xc-522 Source Sampling conSole (engliSh) xc-572 Source Sampling conSole (meTric)
TC-765KF
Temperature Display
Manometer Quick Connects
Fine Control Valve
Manometer Zero Adjust Knobs
Manometer Level Adjust
Standard Stainless Steel Pitot Quick
Connects
Standard Stainless Steel Sample Quick Connect
Standard StainlessSteel Female Pump Connection (Pressure)
UmbilicalCable Power Connection
Color Coded Thermocouple Jacks
7-ChannelTemperature
Selector Switch
Vacuum Gauge
Elapsed Timer
Rugged Custom Molded X-Case
Digital Filter and Probe Temperature
Controllers
Stainless Steel MaleNon-Reversible Pump
Quick Connect(Vaccum)
Strap
9
10
11
1
7
XC-10U19
13
4
21
ElectricReceptacle
Power Connect Inlet
25 3439T12
Heavy Duty Panel Latches
24 L-441160
XC-522 Dry English Gas Meter14 DgM-110
CoarseControl Valve
12 B2VH-6S
Dual Column
Manometer
16 M-42210
1718 QC-MAN-M2
QC-MAN-F32 M-SD31
MC-T
g301U
3
15
M-31302A 6
TC-PJK
QC-BHM6-SS
QC-BHF6-SS
5M-49BK
QC-BHF8-SS8
QC-BHF4-SSAM-MCP NV3HA-6S
M-422B22
M-422DS23
Rocker Switches
M-RA91120
M-SCKT15A
xc-522
28 DgM-AP25
XC-572 Dry Metric Gas Meter
XC-572 (Metric) DGM-AP25 Meter, Dry Gas, AP25 W/Union 28
Magnetic Type Circuit Breaker Rocker Switch
M-CBR3A-M27
M-CBR5A-M26
Call for information on 110V / 240V Models.
11d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
Apex Instruments offers a wide range of filter media to meet any sampling requirements. Listed below are the standard media and sizes that Apex Instruments normally stock. Additional materials and sizes are available upon request.
FILTER MEDIA
QUARTZ FIBER FILTERSQuartz Fiber Filters are manufactured from pure quartz with-out a binder and are frequently used for sampling for metals analyses and acidic gases.
Model DescriptionGF-2Q 2 inch Quartz Fiber Filters-25/box
GF-25Q 25mm Quartz Fiber Filters-100/box
GF-3Q 3 inch Quartz Fiber Filters-25/box (Pallflex 8.26cm)
GF-4Q 4 inch Quartz Fiber Filters-25/box (Pallflex 11 cm)
GF-45Q 45mm Quartz Fiber Filter-100/box
GF-47Q 47mm Quartz Fiber Filter-25/box
GF-54Q 54mm Quartz Fiber Filters-25/box (Pallflex 54mm)
GF-63Q 63.5mm Quartz Fiber Filters-25/box (Pallflex 63.5mm)
GF-3QR 3 inch Quartz Fiber Filters-100/box (MFS QR100 82mm)
GF-4QR 4 inch Quartz Fiber Filters-100/box (MFS QR100 110mm)
GF-47QR 47mm Quartz Fiber Filters-100/box (MFS QR100 47mm)
GF-90QR 90mm Quartz Fiber Filters-100/box (MFS QR100 90mm)
gLASS FIBER FILTERSGlass Fiber Filters are most commonly used filters for particulate sampling. All of the glass fiber filters are binder free and exhibit at least 99.9% efficiency for 0.3 micron dioctyl phthalate (DOP) smoke particles. Not recommended for metals analysis.
grade E FIBER FILTERSIdeally suited for suspended solids analysis and high volume air monitoring applications. Softening point of glass fiber is 500°C, therefore upper limit temperature in use is 475°C. Low fiber shedding improves quality assurance of test results. high loading capacity. This media meets requirements for standard method 2540D and EPA Method 160.2 for establishing water quality in suspended solids content.
Model DescriptionGF-2 2 inch Glass Fiber Filters-100/box
(934AH-5.5cm)
GF-2X6.5 2x6.5 inch Glass Fiber Filters-100/box (934AH)
GF-3 3 inch Glass Fiber Filters-100/box (934AH-8.26cm)
GF-4 4 inch Glass Fiber Filters-100/box (934-AH-11cm)
GF-45 45mm Glass Fiber Filters-100/box (934-AH-45mm)
GF-47 47mm Glass Fiber Filters-100/box(934AH-4.7cm)
GF-63 63.5mm Glass Fiber Filters-100/box (934-AH-63.5mm)
GF-90 90mm Glass Fiber Filters-100/Box (934AH-9.0cm)
GF-2E 2 inch Glass Fiber Filters-100/box Grade E
GF-3E 3 inch Glass Fiber Filters-100/box Grade E
GF-4E 4 inch Glass Fiber Filters-100/box Grade E
GF-25E 25mm Glass Fiber Filters-100/box Grade E
GF-47E 47mm Glass Fiber Filters-100/box Grade E
gLASS FIBER FILTERS
12d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
PTFE COATED GLASS FIBER FILTERS PTFE Coated Glass Fiber Filters are constructed from borosilicate microfibers and bonded with PTFE. The filters can be folded & handled without loss of fibers. Great for especially low loading rates. Specifically recommended for Method 26 & PM10 sampling.
Product DescriptionGF-2T 2 inch PTFE Coated Glass
Fiber Filters-100/box
GF-3T 3 inch PTFE Coated Glass Fiber Filters-100/box (Pallflex 82.6mm)
GF-4T 4 inch PTFE Coated Glass Fiber Filters-100/box (Pallflex 11cm)
GF-25T 25mm PTFE Coated Glass Fiber Filters-100/box (Pallflex 2.5 cm)
GF-47T 47mm PTFE Coated Glass Fiber Filters-100/box (Pallflex 4.7cm)
GF-90T 90mm PTFE Coated Glass Fiber Filters-100/box (Pallflex 90mm)
PTFE FILTER MEMBRANESPTFE Filter Membranes are produced of pure PTFE resins. They withstand the most severely corrosive conditions at temperatures as high as 500°F (260°C) and down to the cryogenic range. The membrane is hydrophobic and maintains its strength wet or dry.
Model DescriptionTF1121 PTFE Membrane, 47mm,
0.45 Micron (10/pack)
TF1131 PTFE Membrane, 47mm, 1-2 Micron (10/pack)
TF1141 PTFE Membrane, 47mm, 5-6 Micron (10/pack)
PTFE FILTER MEMBRANES
Product DescriptionGF-90T 90mm PTFE Coated Glass Fiber Filters-100/box
(Pallflex 90mm)
GF-90T 90mm PTFE Coated Glass Fiber Filters-100/box (Pallflex 90mm)
GF-3TPG 3 inch PTFE Coated Glass Fiber Filters-50/box (MFS PG60) 82mm-Hydrophobic, Low absorption of acid gases such as SOX or NOX.
GF-4TPG 4" PTFE Coated Glass Fiber Filters-50/box (MFS PG60) 110mm-Hydrophobic, Low absorption of acid gases such as SOX or NOX.
GF-25TPG 25mm PTFE Coated Glass Fiber Filters-100/box (MFS PG60) 25mm-Hydrophobic, Low absorption of acid gases such as SOX or NOX.
GF-47TPG 47mm PTFE Coated Glass Fiber Filters-100/box (MFS PG60) 47mm-Hydrophobic, Low absorption of acid gases such as SOX or NOX.
Model Description PriceGF-300C Alundum Thimble, medium porosity, 5+ micron retention, 34x100ml,
round bottom, fits SFA-300 use with additional O-ring, O-123V. $52.00
GF-300-C Alundum Thimble, COARSE porosity, 20 micron retention, 34x100ml, round bottom, fits SFA-300 use with additional O-ring, O-123V.
$54.00
gF-300C
IN-STACK THIMBLES AND ACCESSORIES Apex Instruments stocks a variety of Fiber Thimbles for in-stack particulate sampling. The thimbles are seamless, high purity filters and available from a choice of two different types of fibers: Borosilicate glass and quartz. Borosilicate glass fiber thimbles are acid washed to reduce the trace metal content to an absolute minimum. Quartz fiber thimbles are strengthened with alumina and are prefired at 900°C for 2 hours during manufacturing to stabilize the weight prior to use. The gas collection efficiency of the thimbles is 99.9% (0.3 micron DOP). The 25 x 90mm thimbles are specifically manufactured for stack sampling and tapered for ease in loading. Cellulose thimbles are available upon request.
gF-2590Q
Model DescriptionTF1165 PTFE Membrane, 25mm, 30-60 Micron (10/Pack)
GF-3TM 3 inch PTFE Membrane Filters-50/box (82.6mm) PTFE filter media provides durability for hostile acid aerosol monitoring. 1.0µm pore size membrane.
PTFE FILTER MEMBRANES
Model DescriptionGF-190Q 19X90mm Quartz Fiber Filter
Thimble-25/box (For SFA-190)
GF-300Q 30x100mm Quartz Fiber Filter Thimble-25/box (For SFA-300) grade 88R
GF-2590Q 25x90mm Tapered Quartz Fiber Thimble-10/box (For SFA-2590) Grade 88R
QUARTZ FIBER THIMBLESModel DescriptionGF-190 19x90mm Glass Fiber Filter
Thimble-25/box (For SFA-190)
GF-2590 25x90mm Tapered Glass Fiber Thimble -10/box (For SFA-2590) Grade 86R
GF-300 30x100mm Glass Fiber Filter Thimble-25/box (For SFA-300) Grade 86R
GLASS FIBER FILTER THIMBLES
ACETATE FILTERGF-47MMAT - FILTER, ACETATE, 47MM,.45 PORE, 100/PK. This filter is used in the SK-0061H system for sampling Hexavalent Chromium.
ALUNDUM® THIMBLES (CERAMIC)Alundum® Thimbles are used for in-stack filtration for process engineering studies when a large sample is needed for analyses. These thimbles are made from fused alumina oxide and remain very constant in weight and can be re-used an infinite number of times. There are two different porosity thimbles that can be used in the SFA-300 thimble holder. The medium porosity retain particles 5 micron and larger and the coarse retain particles 20 micron and larger.
13d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
PTFE Probe Brush Extensions The flexible PTFE Probe Brush Extension attaches to the PBT-5/8 or PB-5/8. Made with 8/32 threads with a phenolic knob. Please specify length.
PTFE Probe BrushAll PTFE construction. The PBT-5/8” diameter with four spiral rows of black PTFE bristles. Over all length is 2”. The shaft is 1/4” diameter with 8-32 female threads. PTFE Barrel and PTFE Bristles.PBT-5/8
SAMPLE RECOVERY
PBT-5/8
NB-SET
B-3
B-4
PBX-S
Modular Probe Brush Set The PBX-S Modular Probe Brush Set contains two of the 5/8” stainless steel twisted wire brushes with nylon bristles and a total of 13’ in stainless steel extensions.PBX-S
Model Description
PB- 5/8A Probe Brush/Stainless Steel, Nylon Bristles & Allen Set Screw (HD1088)
PBX-2 2’ Probe Brush Extension, Stainless Steel
PBX-3 3’ Probe Brush Extension, Stainless Steel
PBK-832 Probe Brush Knob
NOZZLE BRUSH SET The NB-SET Nozzle Brush Set includes one each of the three most popular sizes in a convenient carrying tube. (#3,#5,#8)NB-SET
B-1
Impinger Bottle Brush with Plastic Handle and Nylon Bristles.B-1
Impinger Bottle Brush
B-2
Flask Brush, Stainless Steel Handle and Nylon Bristles.B-2
Flask Brush
Filter Brush, 3/16” diameter, Stainless Steel Handle and Nylon Bristles, 5/16”.B-3
Filter Recovery Brush
Rubber Policeman with 18” Delrin® HandleB-4
Policeman
Model Description
PBX-4T 4” PTFE Probe Brush Extension
PBX-6T 6” PTFE Probe Brush Extension
PBX-8T 8” PTFE Probe Brush Extension
PBX-10T 10” PTFE Probe Brush Extension
PBX-12T 12” PTFE Probe Brush Extension
Brush Sold Separately
PTFE NOZZLE BRUSHES Nozzle Brush NBT-1/2 is constructed of pure PTFE featuring a 1/8” diameter shaft with 1/2” long soft PTFE bristles. NBT-1/2
NBT-1/2
PBX- T
NOZZLE BRUSHES Apex Instruments Nozzle Brushes feature stainless steel handle and nylon bristles. Super flexible for cleaning button hook nozzles with eye tip to reduce scarring of the nozzle.
Model Description
NB-3 3/16” diameter, Nylon Bristles
NB-5 5/16” diameter, Nylon Bristles
NB-8 1/2” diameter, Nylon Bristles
NB-5
NB-8NB-3
20 ft.Teflon Sample Line Brush, 1/8” diameter rod with 1/2” long bristles B-5
Sample Line Brush
14d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
POLYETHYLENE SAMPLE BOTTLES
Wide Mouth Bottles for Easy Filling and Pouring. The HDPE bottle with polypropylene closures are made of FDA compliant material. Recycling code molded into base of bottles. Simple to pour-wide mouth bottles. Chemically resistant. Leak proof, firm. Excellent for packaging chemicals, pharmaceuticals and adhesives.
WB-1W - 125 mL vw/Wide Mouth, w/Cap.
WB-2p - 250 mL w/Cap.
WB-2pW - 250 mL w/Wide Mouth.
WB-4p - 16oz./500 mL w/Wide Mouth.
WB-10p - 1000 mL w/Wide Mouth.
WB-1000pW - 1000 mL w/Wide Mouth.
250ML-CYL-PMP
Aluminum Weighing Dishes (70 ml)100/pack.25433-062
Aluminum Weighing Dishes 100 Pack (12.1 cm) 12175-001
Petri Dish 100x15mm PL 25/pack (for 3-inch filters), Polystyrene. 25373-1100
Petri Dish 150x15mm PL 10/pack (for 4-inch filters), Polystyrene.25373-187
graduated Cylinder 250ml, Plastic250ML-CYL-PMP
graduated Cylinder 250ml, Glass250ML-CYL
TW-1
Nylon TweezersTW-1
Polypropylene FunnelTop Diameter 108mm.
30255
Funnel Parafilm M, Laboratory Sealing Film, Roll is 2” x 250 ft.PARA-2X250
Synthetic Cotton Balls (For Impinger Outlet Filter), 300/bagMS-1
Cotton Balls
SAMPLE RECOVERY BOTTLES
FEP WASH BOTTLE500mL Wash Bottles, FEP.WB-500Fep
WB-500FEP
gSB-250
gLASS BOTTLES250mL Glass Sample Bottles with PFA-Lined Lid.Case of 12.gSB-250
SAMPLE RECOVERY ACCESSORIES
WB-5P
PLASTIC WASH BOTTLE500mL Plastic Wash BottlesWB-5p
15d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
PFA
Fittings:
T501-8-2 PFA Impinger Cap, Two 1/2” Tube Fittings
T55 PFA Impinger Wrench Set
NTG-10U2 5/8” Glass Filled PFA Union with 1/8” FNPT Tap (for Nozzle Recirculation)
NTG-10F 5/8” Glass-Filled PFA Single Ferrule
NTG-10F-DZ 5/8” Glass-Filled PFA Single Ferrule (Dozen)
4MSEL2N-PFA PFA Male Elbow,1/4” Tube Union to 1/8”
8-4-10ET-T PFA Jump Tee (1/4”, 1/2”, 5/8” Tube Unions) with Nylon Nuts and TFE Ferrules
10-4-8ET-T Alternate PFA Jump Tee (1/4”, 1/2”, 5/8” Tube Union) with Nylon Nuts and TFE Ferrules
4MSC2N-PFA PFA Union, 1/4” Tube Union to 1/8” MNPT
8-4-8ET-PFA Recirculation Run Tee,1/4”, 1/2”, 1/4” PFA Tube Unions,1/4” Tube Union Bore through Recirculation Line
Used in Method 26 for HCI emissions. TFA-25 High Temper-ature PFA clamp nuts are standard. 1/4” tube fittings. TFA-47 Standard with 1/4” tube unions. Also available with 1/4” male pipe fittings or 3/8” tube fittings.
TFA-25
TFA-47
PFA Filter Assemblies:
TFA-25 PFA 25mm Filter Assembly, 1/4” Tube Fittings
TFA-25B 25mm PFA Filter Replace Body Only with 1/4” TU, No Clamp
TFA-47 PFA 47mm Filter Assembly, 1/4” Tube Fittings
TFA-47-6 PFA 47mm Filter Assembly, 3/8” Tube Fittings
TFA-47-6T PFA 47mm Filter Assembly, 3/8” Tube Stubs
Segmented PFA Column & Accessories:T501 PFA Column End Cap, SolidT501-4 PFA Column End Cap with 1/4” Tube Fitting T501-4-2 PFA Column End Cap with two 1/4” Tube FittingsT501-6 PFA Column End Cap with 3/8” Tube FittingT501-6-2 PFA Column End Cap with two 3/8” Tube FittingsT502 PFA Column Connector T504 PFA Column Segment T504-4 PFA Column Segment with 1/4” ube Fitting T504-6 PFA Column Segment with 3/8” Tube Fitting T504-47 PFA Column Segment - Adapts to 47mm Filter HolderT504S PFA Screen, Separator slides into T504T570 PFA Column Segmnet, Solid Bottom
T504-6 Column Segment with Fitting
T504 Column Segment
T501-4 One Port Column End Cap
T501 Column End Cap
T502Column
Connector
T570 Column Segment with Solid Bottom
T501-4-2 Two Port Column End Cap
T504-4
Grooved Vessel
T507G Impinger Single Piece Body, 375ml
PFA L-Stems:
T507-3 L-Stem, 1/2” FEP, Full Length
T507-3R L-Stem, 1/2” FEP, Restricted Tip
T507-5 L-Tube Outlet, 1/2” FEP, Short Ends
PFA U-Stems:
T507-1 U-Stem, 1/2” FEP, Plain Tip
T507-1R U-Stem, 1/2” FEP, Restricted Tip
PFA Straight Stems:
T507-2 Straight Stem, 1/2” FEP, Full Length
T507-2R Straight Stem, 1/2” FEP, Restricted
T507-6 Straight Tube Outlet, Short End
T5072
Hexavalent Chromium PFA Impinger Trains
PFA COLUMN COMPONENTS
Features: • Unbreakable
• Leak Tight without Sealants
• Grooved for Heat Transfer
PFA Column Components are PFA fluorocarbon resin and inert to virtually all chemicals. All are usable for a wide variety of temperature ranges from below 32°F to 500°F (0 to 260°C). The individual components can be assembled for a variety of uses. Components can be purchased separately and assemble according to project specifications.
Vgc-12
Although used primarily as SO2 scrubbers for U.S. EPA Method 16A, determination of total reduced sulfur emissions from stationary sources, the T507g Impinger can be used in other procedures such as Methods 5 and 6 (hexavalent chrome).
PFA Impingers, Stems and Fittings
PFA Impingers and Accessories PFA Filter Assemblies
• Adaptable for Adding Recirculation Fittings
• Quick Connections with Preformed Tube Bends
16d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
BALANCES
MODEL DESCRIPTION
BAL-EJ1500 1500g x 0.1 g.
BAL-EJ3000 3100g x 0.1 g.
BAL-EJ6100 6100g x 0.1 g.
BAL-EJ02 USB Interface with Cable
BAL-EJ12 Carrying Case
EJ-SERIES• Easy to read LCD Display with Backlight
• Percentage and Counting
• USB or RS-232 Interface Optional
• Battery Operated (4 x AA not included)
• AC Adapter Included
• Pan Size: 5” x 5.5”
• Check-Weighing Capacity
• 5 Year Warranty
PORTABLE BALANCES
MODEL DESCRIPTION WEIgHT
BAL-W1000ASTM Weight for Electronic Balance. 1 kg. ASTM GRADE 7
BAL-W2000ASTM Weight for Electronic Balance. 2 kg. ASTM SHAPE
BAL-W5000ASTM Weight for Electronic Balance. 5 kg. Class F, Meet Tolerances of NIST (Comes with case)
ELECTRONIC BALANCE - CALIBRATION WEIgHT
comES with cErtificatE of conformancE
17d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
BALANCES
MODEL DESCRIPTION PAN SIZE
BAL-HR60-C 60g x 0.1mg with RS-232C. 3.3”
BAL-HR120-C 120g x 0.1mg with RS-232C. 3.3”
BAL-HR200-C 210g x 0.1mg with RS-232C. 3.3”
BAL-HR202i 220g/51g x 0.1mg/0.01mg Semi-Micro with R-232C. 3.6”
HR-SERIES• Percentage and Counting Modes.
• Digital Preset Tare.
• One Touch Printing.
• Last Digital Suppression.
• Standard Underhook.
• Optional Rechargeable Battery Pack.
• GLP/LIMS/ISO Compliant.
• RS-232C Standard.
• 5 Year Warranty.
ANALYTICAL BALANCES
Analytical Balances - Calibration Weight Set
MODEL
BAL-W1-100
DESCRIPTIONWeight Set - 1mg-100gStainless Steel Calibration Weight Set for Lab Use. Set of 9 Weights Plus Fractional Weights in Wooden Storage Box.
Note: Please check with State Department of Weights and Measurements for calibrations.
18d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
DESICCATOR AND DESICCANTS Acrylic Desiccator Cabinets feature adjustable shelves with grooves for positioning, removeable lip tray, gasketed door, built-in hygrometer. Cabinets do not include Desiccant, order separately.
31000
www.belart.com
Features• Patented Sealed Construction is Airtight, Dust and Moisture Free.• Portable and Stackable with a Small Footprint.
PORTABLE DESI-VAC CONTAINER Desiccator with a vacuum pump is ideal for drying, preserving, storing, and even shipping samples. Vacuum pump built into the top removes air with manual strokes. Rubber O-ring sealed cover maintains vacuum. Achieves a vacuum of better than 200 inches of water (15 inches of mercury). A release button on top allows air into the container to remove the lid. Sample Humidity Sponges™ desiccant drying packets are included. O-ring-sealed cover maintains vacuum. Achieves a vacuum of better than 200 inches of water (15 inches of mercury A release button on top allows air into the container to remove the lid. Keep powder dry. Plastic container is ideal for storing chemicals, powders, tissues, plant sections, electronics, and weighing samples. Vacuum and desiccants keep mate-rial dry. Supplied with a vacuum indicating button that confirms interior vacuum and a dial hygrometer that displays 0 to 100% relative humidity with a resolution of 2%RH.Dimensions: HxWxD: 11” x 9” x 10”.
DeS-3164DES-3164
• Embedded UV Protection and Superior Chemical Resistance.• Built-in Hygrometer for Quick Check on RH Levels.• Rugged Construction with Sturdy Latches and Lock Provisions.
Model Description Dimensions Features
DES-10000 Desiccator Cabinet 8.4” x 13.4” x 16.3” Gasketed door, built in hygrometer, 0.75 cu.ft.
DES-21000 Desiccator Cabinet 12.4” x 13.4” x 16.3”, Gasketed door, 2 shelves, built in hygrometer 1.17 cu.ft.
DES-21115 Auto-Desiccator Cabinet
12.4” x 13.4” x 16.3” Gasketed door, 2 shelves, built in hygrometer 1.17 cu.ft. 110V
DES-21115V Auto-Desiccator Cabinet
12.4” x 13.4” x 16.3”, Gasketed door, 2 shelves, built in hygrometer 220V fan, 1.17 cu.ft.
DES-31000 Desiccator Cabinet 16.4” x 13.4” x 16.3”, Gasketed door, 3 shelves, built in hygrometer stackable
DES-31115 Auto-Desiccator Cabinet
16.4” x 13.4” x 16.3”, Gasketed door, 3 shelves, built in hygrometer stackable, 110V
DES-31115V Auto-Desiccator Cabinet
16.4” x 13.4” x 16.3”, Gasketed door, 3 shelves, built in hygrometer 220V fan
DES-40000 Desiccator Cabinet 13.4” x 20.4” x 16.3”,
Gasketed door, 2 shelves, horizontal Profile
DES-41115 Auto-Desiccator Cabinet
20.4” x 13.4” x 16.3” Gasketed door, 3 shelves, built in hygrometer
DES-41220 Auto-Desiccator Cabinet
20.4” x 13.4” x 16.3”, Gasketed door, 3 shelves, built in hygrometer, 220V fan
19d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
Adsorption Housing, 1/4” FNPT Fittings. Without Sorbent.
SILICA gELBlue Indicating, 12/case, 250 ml per bottle.
Sg-KiTSg-KIT
Apex Instruments Silica Gel is primarily used for drying sample gas prior to measurement and can absorb moisture 40% of its weight. The silica gel can be regenerated by drying in an oven and used over and over again.
SILICA gEL
SILICA gEL3-5mm Bead, Indicating, 2.3Kg.
Sg-3/5B
24005 14005
Part Number Description
14005 DRIERITE®, Nonindicating 10-20 Mesh, 5 Lbs. (2.3 kg)
23005 DRIERITE®, Indicating 8 Mesh, 5 Lbs. (2.3 kg)
24005 DRIERITE®, Indicating 10-20 Mesh, 5 Lbs. (2.3 kg)
26840 DRIERITE®, Cartridge, 50g H2O Capacity
26809 Mounting Clip for Use with Gas Drying Units
Sg-3/5B
The activated alumina is primarily used for air drying at low temperature applications, 5.5 lb. Container.
80% Activated Alumina (White). 1/8” Diameter Beads.
20% Silica Gel (Blue) 3-5 mm Beads.
aluma-sorb
ACTIVATED ALUMINA WITH SILICA gEL
Aluma-sorb
SILICA gEL3-5 mm Bead, Bulk55 LBS, CONTAINER.
Sg-3/5B-55
AH-610R
DRIERITE® DESICCANTSApex Instruments carries both non indicating and indicating DRIERITE®. (anhydrous calcium sulfate) Economical to use, it can be regenerated repeatedly. The indicating DRIERITE® is impregnated with cobalt chloride: blue when dry and changes to pink upon absorption of moisture.
Sg-3/5B-55
ah-610r
20d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
Product DescriptionPF-346T32S 2” FNPT, Universal Pipe Flange Reducer, Fits 3”, 4”, 6” Ports, SSPF-346XT32S 2” FNPT, Universal Pipe Flange Reducer with 12” Extension,
Reversible, Fits 3”, 4”, 6” PortsPF-346T32S 2” FNPT, Universal Pipe Flange Reducer, Fits 3”, 4”, 6” Pipe
Flanges, Stainless SteelPF-4/6U32-S Universal Pipe Flange with 2” FNPT, Fits 4” and 6” PortsPF-4/6UB-S Universal Pipe Flange, 4”/ 6” Port, 2.675 Bored Center, SSPF-4/6UCLS Universal Flange, 4”/ 6” w/ 2-1/2” Cam-Lock
UNIVERSAL PIPE FLANgE & FLANgE REDUCERS
CAM-LOCK, FLANgES, PORT ADAPTERS & PACKINg gLANDS
Flange & Cam-Locks
Threaded Pipe Flanges
REDUCING FLANGES
Product DescriptionPF-3/40CLS 3” Bored Pipe Flange, 150 lb pattern, 2.670
Bored Diameter, with size 40Cam-lock Connector, Stainless Steel
PF-3CS 3” Pipe Flange, 150 lb FF Pattern, Bored with Threaded Coupling, Stainless Steel
PF-4BS 4” Bored Pipe Flange, 2.67” RF, 150 lb Pattern, Stainless Steel
PF-6BS 6” Bored Pipe Flange, 150 lb Pattern, 2.670 Bored Diameter, Stainless Steel
PF-4CLS 4” Bored Pipe Flange, 2.67” RF, 150 lb Pattern, Stainless Steel
PF-4CS 4” Bored Pipe Flange, 150 lb FF Pattern with Threaded Coupling, Stainless Steel
PF-4/40CLS 4” Bored Pipe Flange, 150 lb pattern, 2.67 Bored Diameter Welded Cam and Groove Connector (For Probes without Pitot Option, with Tube Outer Sheath) with size 40 Cam-Lock Connections, Stainless Steel
PF-6/40CLS 6” Bored Pipe Flange, 150 lb pattern, 2.67 Bored Diameter welded Cam and Groove Connector (For Probes without Pitot Option, with Tube Outer Sheath) with size 40 Cam-Lock Connections, Stainless Steel
PF-6/48CLS 6” Bored Pipe Flange, 150 lb Pattern, Bored Inside Diameter, with size 48 Cam-lock Connector (For Use with Pitot Version Mercury Probe with Pipe Oversheath),Stainless Steel
PF-6CLS 6” Bored Pipe Flange, 150 lb pattern, 2.670 Bored Diameter, with Cam-lock Connector, Stainless Steel
BORED PIPE FLANgE
Product DescriptionPF-3BLS 3” Pipe Flange, 150 lb RF, Blind, Raised Face, 7-1/2” OD, 6” Bolt
Circle Diameter, Stainless SteelPF-4BLS 4” Pipe Flange, 150 lb Pattern, Blind, Raised Face, 9” OD, 7-1/2”
Bolt Circle Diameter, Stainless SteelPF-6BLS 6” Blind Pipe Flange, 150 lb Pattern, 11” OD, 9-1/2” Bolt Circle
Diameter, Stainless Steel
BLIND PIPE FLANgES
Product DescriptionPF-2T 2” Threaded 304 Flange, 6” OD, 4-3/4” Bolt Circle Dia. Carbon SteelPF-3T 3” Threaded Pipe Flange, 150 lb., Pattern, 7-1/2”
OD, 6” Bolt Circle Diameter, Carbon SteelPF-4T 4” Threaded Pipe Flange, 150 lb., Pattern, 9” OD,
7-1/2” Bolt Circle Diameter, Carbon SteelPF-6T 6” Threaded Pipe Flange, 150 lb., Pattern,
11” OD, 9-1/2” Bolt Circle Diameter, Carbon Steel PF-3TA 3” FNPT Threaded Pipe Flange, 150 lb., Pattern,
7-1/2” OD, 6” Bolt Circle Diameter, Cast AluminumPF-4TS 4” FNPT Threaded Pipe Flange, 150 lb., Pattern,
9” OD, 7-1/2” Bolt Circle Diameter, Stainless SteelPF-6TS 6” FNPT Threaded Pipe Flange, 150 lb., 11” OD,
9-1/2” Bolt Circle Diameter, Stainless Steel PF-3T16 3” Threaded Pipe Flange, 150 lb., Pattern, 7-1/2”
OD, 6” Bolt Circle Diameter, Carbon SteelPF-4T16 4” Threaded Pipe Flange, 150 lb., Pattern, 1” FNPT,
9” OD, 7-1/2” Bolt Circle Diameter, Stainless SteelPF-4PG38S 2” Pipe Flange, 150 lb Pattern, 6” OD, 4-3/4” Bolt Circle Diameter,
with 2” Pipe Packing Gland, Stainless SteelPF-6PG38S 6” Pipe Flange, 150 lb., Pattern, 11” OD, 9-1/2” Bolt Circle Diameter,
with 2” Pipe Packing Gland, Stainless Steel
THREADED PIPE FLANgES
PIPE FLANgE
Product DescriptionPFC-2.5S 2.5” Probe Flange Cap Assembly, Consists of 304 Stainless
Steel Bevel Seat Cap and NutPFC-2S 2” Probe Flange Cap Assembly, Consists of 304 Stainless Steel
Bevel Seat Cap and Nut
PROBE FLANgE CAP
Product DescriptionPF-4PG38S 4” Pipe Flange, 150 lb Pattern with 2” Pipe Packing Gland (For Use
with Probes with Pitot Option, Pipe Outersheath), Stainless Steel PF-346S Flange Plate with 2-3/8” Hole for 2” Pipe. Fits 3”, 4” & 6” Ports, SSPF-46XT32S 2” FNPT Probe Support with Extension
21d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
Product DescriptionPF-346PG38 Packing Gland Flange Fits 3”, 4”, 6”,
Includes Packing Gland for 2” Pipe, Stainless Steel
PACKINg gLAND FLANgE
Bored Bushings Reducing Bushings
Product Description64M/32F-CS Reducing Bushing, 4” MNPT-2” FNPT, Carbon Steel48M/32F-CS Reducing Bushing, 3” MNPT-2” FNPT, Carbon Steel32M/16F-B Reducing Bushing, 2” MNPT-1” FNPT, Brass32M/24F-B Reducing Bushing, 2” MNPT-1.5” FNP, Brass
REDUCINg BUSHINgS
Product Description32M/16B-B Bored Bushing, 2” MNPT X 1.035” Bore, Brass32M/24B-B Bored Bushing, 2” MNPT X 1.535” Bore, Brass32M/32B-B Bored Bushing, 2” MNPT X 2.035” Bore, Brass
BORED BUSHINgS
Packing glands
Cam-LockPacking glands
OversheathPacking glands
PF-4/6UCLS
Pg-32/40CL
PF-4/40CLS PF-6/40CLS
Product DescriptionPG-24T 1-1/2 inch Oversheath Packing Gland, Steel Body, 1-1/2
inch MNPT, TFE PackingPG-32S 2” Oversheath Packing Gland, Steel Body, 2” MNPT, PTFE
Ferrule includedPG-32/40CL 2” Oversheath Packing Gland, Steel Body, TFE Packing
(for use with PF-40CLS flange) with size 40 Cam and Groove Connector
PG-38/48CL 3” Oversheath Packing Gland, Stainless Steel body, Cam-Lock, For use with Pitot Version Mercury Probes with Pipe Oversheath
OVERSHEATH PACKINg gLANDS
PACKINg gLAND ACCESSORIES
Product DescriptionPG-32F 2” Adapter, Threaded Bevel Seat, #21-2, Custom Bore,
2.125” ID, Used in PG-32S, Stainless Steel, Note: Does Not Include Nut or Ferrule
PG-32NT 2” Adapter, Bevel Seat, #21-2, Custom Bore, 2.125” ID, Welded to PF-XXX Flange Assembly, Extention, or PC-XXX. Note: Does Not Include Nut or Ferrule
PG-38F 2.5” Custom Threaded Ferrule, Part of PG-38-3Q Packing Gland, Stainless Steel
PG-38RT Thrust Ring, 2.435 ID X 2.875 OD, for PG-38-3Q Packing Gland, Stainless Steel
PG10-4N Pressure Gauge, 0-15 psi, 1/4” NPT, Stainless Steel PG200-4N Pressure Gauge, 1/4” NPT
PACKINg gLANDS FOR PITOTS
Product Description12MTC12-B 3/4” Packing Gland for Pitot with 3/4” Oversheath,
Includes Nylon and Brass Ferrules, Brass12MTC12-S 3/4” Packing Gland for Pitot with 3/4” Oversheath,
Includes Nylon and Ferrules, SS16MTC16N-B 1” Packing Gland for Pitot with 1” Oversheath16MTC16N-S 1” Packing Gland for Pitot with 1” Oversheath,
Includes Stainless Steel Ferrule16MTC16N-SF 1” Packing Gland for Pitot with 1” Oversheath, includes
Nylon Ferrules, Stainless Steel, and 16MTC16-S12F-GR 3/4” Graphite Ferrule, Alternative Packing for 16MTC1616F-GR 1” Graphite Ferrule, Alternative Packing for 16MTC16
360 DEgREE COMPASS ROSE FLANgE
Product DescriptionPF-346T32A360 Flange with 360 Degree (0-90 Degree X 4) Compass
Rose Laser Engraved. 2” Half Coupling Welded. Fits 3”, 4” and 6” Flanges. Includes Arrow Pointer for 2” Oversheath Probe, Stainless Steel
PF-346XT32S360 Flange with 360 Degree (0-90 Degree X 4) Compass Rose Laser Engraved. 2” Half Coupling Welded. Fits 3”, 4” and 6” Flanges. Includes Arrow Pointer for 2” Oversheath Probe. With Bored Bushings and 2” Diameter Probe Support Extension, SS
Product DescriptionPFC-40S-CL 2.5” NPT 316 with Buckles, Cap Cam with Groove
Fitting, Type D, 2.5 inch MNPT, SS
PIPE FLANgE ACCESSORIES
Product Description64RUC32-CS Coupling, Reducer, 4” x 2” FNPT, Carbon Steel48RUC32-CS Coupling, Reducer, 3” x 2” FNPT, Carbon Steel
REDUCINg COUPLINgSReducing Couplings
22d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
MEtER CAlIbRAtIOn
CAlIbRAtIOn SERvICESApex performs both calibrations using a wet test meter and bell-prover primary standard. Calibration services are available from Apex Instruments on a fee per console basis. Extra charge for low flow. All console and dry gas meter calibrations are conducted in accordance with U.S. EPA standards. Apex Instruments calibrates source sampler consoles, reference dry gas meters, orifices and pitots.
Calibration being performed with Wet Test Meter
Model Description
DGR-2VER Verification of DGM for Secondary Reference, 2 Point Verification of Previous Calibration
DGMC-5A Pre-Test 5 Point Calibration for Compatible Meter Consoles
DGMC-3A Post Test 3 Point Calibration for Meter Consoles
CAL-ORF Orifice Calibration, 3 Point
DRy GAS MEtER CAlIbRAtIOn SERvICES
MEtER CAlIbRAtIOn EquIpMEnt
DRy GAS SECOnDARy REfEREnCE MEtER (EnGlISh)Dry Gas Meter Secondary Reference Meter (Standard) with 15 pt cal, valve, 5’ hose, 1/2” Quick Connect. Used for calibrating Method 5 Source Sampler Consoles.
DGM-110SR
DGM-110SR
DRy GAS MEtER KG3S W/ REplACEMEnt KIt fOR SK25 DGM In XC-572 Replacement Kit for KG3S to replace SK25 DGM in an existing model XC-572 meter console. Includes KG3S DGM with nuts and o-rings, adapter plate, support bracket, bushings, standoffs and screws.
DGM-KG3SKKITDGM-KG3SKKIt
DRy GAS MEtER KG3S W/ REplACEMEnt KIt fOR Ap25 DGM In XC-572 Replacement Kit for KG3S to replace AP25 DGM in existing model XC-572 meter console. Includes KG3S DGM with nuts and o-rings, adapter plate, bushings, standoffs and screws.
DGM-KG3APKIT
The configuration for the replacing the AP25 does not require the support bracket.
DGM-KG2SRDDGM-KG3SRDGM-KG3-SRD5K
23d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
DIAL CALIPERS
Geometric of Type-S Pitot Tube to Method 2.
pT-cal-gWind Tunnel of Type-S Pitot Tube to Method 2.
pT-cal-W
PITOT CALIBRATION SERVICES
THERMOCOUPLE SIMULATOR / CALIBRATOR This Thermocouple Simulator/Calibrator is convenient for checking the accuracy of most Controllers and Temperature Displays. Whe Cold Junction Compensated, is calibrated without External Compensators or Icebaths the Simulator Source is designed for Type-K Thermocou-ples and has 22 precise test points.
m5c-520
Dial Calipers are used for measuring nozzle diameter and inspection of pitots. Dial Caliper, 0-6”/ 150mm Direct inch/Metric Conversion.
m5c-3D...$75.00
NOZZLE CALIBRATION
CALIBRATION EQUIPMENT AND SERVICES
M5C-520
BULL’S EYE LEVELBull’s Eye Level is 1/2” diameter and used for pitot calibrations. Comes with thumb screws for clamping to pitot.
m5c-2
M5C-2
Pendulum Style Inclinometer for the Calibration of Type-S Pitots.
inc-a300
A300 LEVEL INDICATOR
INC-A300
PITOT AUDIT EQUIPMENT & MANOMETERS
Meriam Handheld, LCD DISPDigital Manometer, Hand held, 0-28 inch H2O Selectable Range, English/Metric, with certificate of NIST traceability.
Dhm-m100
HANDHELD MANOMETER
DHM-M100
HANDHELD MANOMETER LCD DISP., Digital Manometer, Method 2, Hand held, 0-10 inch H2O Selectable Range, English/Metric.
Dhm-28-10
DHM-28-10
MANOMETER SOFTWARE Software and cable for Digital Manometer, HM28 series.
Dhm-28-1
MANOMETER DIgITAL DISPLAYDP-CALC Micromanometer makes differential pressure measurements, static, total, and velocity pressures as well as pressure drops across filters, coils, fans, and diffusers. Differential and static pressure from -15 to +15 in. H2O (-3735 to +3735 Pa) lightweight and durable design with an easy-to-read display, certificate of NIST traceability.
Dhm-5825
24d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
oriFice FloW meTerS
OFM-SERIES ORIFICE FLOW METERS
The OFM-Series Orifice Flow Meters all feature a calibrated, stainless steel critical orifice with two liquid-filled vacuum gauges and stainless steel inline filter. All fittings, including the orifice and filter, are made of stainless steel and include 1/4” tube fitting end connections. These adapters are used with vacuum pumps to provide constant sample flow rates. Orifice sizes range from 4 to 35 providing flow rates from 0.076 Lpm to 6.1 Lpm.
VUA-SERIES LOW FLOW ADAPTERS
The VUA-Series Low Flow Orifice Adapters feature a calibrated, critical sapphire orifice with liquid filled vacuum gauge, brass fittings and inline filter to adapt to Apex Instruments’ isokinetic source samplers for methods requiring low flow sampling. The adapters are used for VOST and Method 6-type sampling. Adapters include 1/2” male and 1/4” female brass quick connects to attach the isokinetic source sampler to the VOST VU-cords. Three adapters are offered to provide approximately 1/2, 1 and 2 liters per minute flow rates. The VUA-575 is used for Method 7C to provide the required flowrate between 400-500cc/min.
Product Description
VUA-561 Low-flow Adapter for Isokinetic Meter Console, ~1Lpm, 1/2” male 1/4” female quick connect, brass
VUA-562 Low-flow Adapter for Isokinetic Meter Console, ~2Lpm, 1/2” male 1/4” female quick connect, brass
VUA-565 Low-flow Adapter for Isokinetic Meter Console, ~0.5 Lpm, 1/2” male-1/4” female quick connect, brass
VUA-575 Low-flow Adapter (M7C) for Isokinetic Meter Console, ~0.5Lpm, 1/2” male-1/2” female quick connect, brass
VUA-SERIES LOW FLOW ADAPTERS
Product Description
KFR-4A40SNVT Acyrlic, 0.4-5 Lpm, Stainless Steel, No Valve
KFR-4A44SNVT Acyrlic, 4-50 Lpm, Stainless Steel, No Valve
KMR-3A13SVVT Polycarbonate, 0.1-1.2 Lpm, Stainless Steel, with Valve
KMR-3A23SVVT Polycarbonate, 0.2-2.5 Lpm, Stainless Steel, with Valve
KMR-3A14SVVT Polycarbonate, 0.4-5 Lpm, Stainless Steel, with Valve
KGS-SERIES Glass Tube, Rotating Lens, MM Scales or Direct Read Index
KGR-SERIES Glass Tube, standard lens, MM Scales or Direct Read Index
Apex Instruments offers the precision machined acrylic (KFR-Series), molded polycarbonate (KMR-Series), glass tube(Kg#-Series), and electronic flowmeters for a variety of applications. Available in precision engineered sizes and scales for a variety of fluids. The millimeter reference or direct read scales can be specified to meet any requirements. NIST traceable calibration certificates are available.
FLOW METERS
KFR-Series - KMR-Series - KgS-Series
Product Description
OFM-K4-14 Orifice Control Flowmeter, In-Line, w/2 liquid Filled Vaccum Gauges, Stainless Steel In-Line Filter & KA-14-SS Orifice, 1Lpm
OFM-K4-4 Orifice Control Flowmeter, In-Line, w/2 Vacuum Gauges, Stainless Steel In-Line Filter & K4-4-SS Orifice, .076LPM
OFM-K4-6 Orifice Control Flowmeter, In-Line, w/2 Vacuum Gauges, Stainless Steel In-Line Filter & K4-6-SS Orifice, .20 lpm
OFM-K4-7 Orifice Control Flowmeter, In-Line, w/2 Vacuum Gauges, Stainless Steel In-Line Filter & K4-7-SS Orifice, .28 lpm
OFM-K4-8 Orifice Control Flowmeter, In-Line, w/2 Vacuum Gauges, Stainless Steel In-Line Filter & K4-8-SS Orifice, .34lpm
OFM-K4-9 Orifice Control Flowmeter, In-Line, w/2 Vacuum Gauges, Stainless Steel In-Line Filter & K4-9-SS Orifice, .45 lpm
OFM-K4-HG Calibration Orifice, In-Line, w/ Vacuum Gauge, Stainless Steel In-Line Filter & Orifice, low flow for mercury system
other flow ranges available.
OFM-SERIES ORIFICE FLOW METERS
other flow ranges available. caLL for DEtaiLS & PricinG.
FLOW METERS (ROTAMETERS)
25d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
REMOTE INCLINOMETER LED DISPLAY (INC-D205)The INC-D205 Remote Inclinometer Display is designed to be used inconjunction with our INC-A2T inclinometer sensor. The display is a highresolution 3 1/2 digit bright LED process meter. The meter is housed in a sturdy compact metal cabinet with convenient carrying handle. RequiresINC-A2T Sensor and Signal Cable (INC-SC-”length”). SC voltage 120/60Hz.Dimensions: 6” x 7” x 8.5”Weight: 4 lb.
INCLINOMETERSThe INC-A2T-50 Inclinometer Sensor is designed for measuring the yaw angle of flow in accordance with Method F&G. The standard collar is designed for clamping onto 2” tubing. Remote Inclinometer Sensor, 360 degrees with 2” Tube Clamp and Amphenol Connector has analog voltage output. Alternative clamp sizes are available upon request. This remote sensor is designed to be used with the 3-D flow console, however it can be used with the Remote Digital Display (INC-D205). The inclinometer sensor is connected to the display via our standard 4-pin Signal Cable.
PROTRACTOR / INCLINOMETERThe M5C-4 Protractor/Inclinometer is an ideal tool for measuring cyclonic yaw angles in accordance with Method 2. The machined aluminum frame and integral baseplate provide a light, rigid and ultra precise platform allowing the state-of-the-art sensor to provide unsurpassed accuracy throughout the 360° range. The inclinometer can be securely attached to probe with one of the following mounting brackets.
m5c-4
INC-A2T-50INC-D205
Bracket for M5C-4 with 1” Aluminum Clamp.m5c-4-16
Bracket for M5C-4 with 2” Aluminum Clamp.m5c-4-32
Mounting Brackets for M5C-4
M5C-4PENDULUM STYLE INCLINOMETEREasy-to-use, hand-held Pendulum Style Inclinometer. 1/10deg accuracy:Includes plastic case.. The dial is 2.6”dia. with vernier divisions of 1/10deg. Height is 3.6”, width is 3.1”, wt :3.6oz.
inc-a300
Features:• Reliable: 15 years of proven DryCal® performance• Accurate: Backed by ISO 17025; NV LAP accredited• Portable: Lightweight and impact-resistant• Simple: Quick Start operation and no messy soap solutions• Streamlined: Bios optimizer software transfers calibration data directly to any windows based PC using built in serial port.
FLOW CALIBRATOR/PISTON PROVER / BIOS Defender 510 and 520 Series are the next generation of DryCal® technology. It is the proven and reliable foundation of all BIOS primary standards, and the basis of our ISO 17025 accreditation by NVLAP of NIST. Available in low, median or high ranges.
Model Description
200-510H Flow Calibrator, Defender 200-510H, High Flow Range, 300ml-30,000ml/min, +/-1% of Reading Volumetric
200-510L Flow Calibrator, Defender 200-510H, Low Flow Range, 5ml-500ml/min, +/-1% of Reading Volumetric
200-510M Flow Calibrator, Defender 200-510H, Medium Flow Range, 50ml-5000ml/min, +/-1% of Reading Volumetric
200-520H Flow Calibrator, Defender 200-510H, High Flow Range, 300ml-30,000ml/min, +/-1% of Reading Volumetric, Includes Temperature and Pressure Recordings
200-520L Flow Calibrator, Defender 200-510H, Low Flow Range, 5ml-500ml/min, +/-1% of Reading Volumetric, Includes Temperature and Pressure Recordings
200-520M Flow Calibrator, Defender 200-510H, Medium Flow Range, 50ml-500ml/min, +/-1% of Reading Volumetric, Includes Temperature and Pressure Recordings
INC-A300
BIOS DEFENDER 510 AND 520 SERIES
FLOW METERS (ROTAMETERS)
inc-D205inc-a2T-50
26d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
Product Description
TPFA-o/ o PFA (Perfluoralkoxy) combines the attributes of PTFE and FEP. The working temperature is 500ºF (260ºC). Color is Clear with a light blue tint. Highest resistance to chemical; pharmeceutical grade; less likely to kink.
PTFE-o/ o PTFE (Tetrafluoroethylne) possess the lowest coef-ficient of friction of any known solid and is used widely because of its anti-stick properties which allows easy cleaning. PTFE has chemical resistant qualities and is unaffected. Working temperature is 500ºF (260ºC), Color is milky white.
PTFE TubingPTFE Resin is supplied in powdered form, which is extruded into a paste and then finally tubing. It is translucent white in color. The minimum and maximum temperature ranges are <-170°C to 260°C (-275°F to 500°F). Tensile strength is 3200 psi.
TPFA-10/8 Tubing, PFA, 1/2” ID x 5/8” OD x .062 wall
TPFA-4-047 Tubing, PFA, 5/32” ID x 1/4” OD x .047 wall
TPFA-4/2 Tubing, PFA, 1/8” ID x 1/4” OD x .062 wall
TPFA-6/4 Tubing, PFA, 1/4” ID x 3/8” OD x .062 wall
TPFA-8/6 Tubing, PFA, 3/8” ID x 1/2” OD x .062 wall
TUBINg
PFA Tubing with Stainless Steel OverbraidTubing constructed of an extruded innercore of Virgin PFA with a 304 stainless steel braid reinforcement. The innercore is non-aging and has a long flex-life, it is weather resistant and the nonstick surface makes cleaning an ease. The braid acts as both a carrier of pressure and a protective covering. Requires Tube Stub Crimps (6TS6C-S) for each end (per foot).
TTO- o - o (Nominal)
TTO-4 PTFE Tubing with Stainless Steel Overbraid, nom.1/4” Requires Tube Stub Crimps (4TS4C-S) Each End, Per Ft.
4TS4C-S Tube Stub Crimp,1/4” One Used on Each End of Stainless Steel Overbraided, PTFE Tubing
TTO-6 PTFE Tubing with SS Overbraid, nom. 3/8” Requires Tube Stub Crimps (6TS6C-S) Each End, Per Ft.
6TS6C-S Tube Stub Crimp, 3/8” One Used on Each End of Stainless Steel Overbraided, PTFE Tubing
TTG-10/6 PTFE Probe Liner Material, 5/8” OD, 3/8” ID, Price Per Ft.
Product Description
TT-2/1 1/8” OD, 1/16” ID, Natural PTFE Heavy Wall Tubing
TT-4/2 1/4” OD, 1/8” ID Natural PTFE Heavy Wall Tubing
TT-6/4 3/8” OD, 1/4” ID Natural PTFE Heavy Wall Tubing
TT-8/6 1/2” OD, 3/8” ID Natural PTFE Heavy Wall Tubing
TT-10/8 5/8” OD, 1/2” ID Natural PTFE Heavy Wall Tubing
PFA TubingPFA Resin is translucent white in color.
fEP tubing fEP tubing is available.
Stainless Steel TubingUsed for precise flow and miniature applications. It is hard tempered for excellent machinability and has high tensil strength. Temperature range is -250°C to 315°C (-425°F to 600°F). Call for pricing.
Apex Instruments Inconel Tubing is made from a nickel-chromium alloy with excellent oxidation resistance against cracking or breaking at higher temperatures. Our Inconel tubing is corrosion resistant to stress caused by caustic substances and is often used for thermocouple protection tubing. The temperature range is -132°C to 650°C (-205°F to 1200°F). Be sure to use with compression fittings. Call for pricing.
Inconel Tubing
Polyurethane TubingPolyurethane Tubing offers an excellent resistance to kinking, abrasion, hydrolysis, oxidation and ozone. It also offers high resilience, good energy absorption and good at over all chemical resistance. It is excellent in applica-tions requiring superior toughness and resistance to tear, abrasion, fungus and humidity.
TU-o / o -o (Tube OD) / o (Tube ID)
TU-4/2 Polyurethane, 1/4” OD, 17” ID (Per Foot)
TU-6/4 Polyurethane, 3/8” OD, 1/4” ID (Per Foot)
Extruded from linear low density Polyethylene Resin, this tubing is tough and flexible. It is chemical and moisture resistant and has a wide range of uses in industrial and agricultural applications.
Polyethylene Tubing
TP-o / o o -o (Tube OD ) /o (Tube ID) o(Color; BK= Black, BL=Blue, NA=Natural, OR=Orange, YW=Yellow)
TP-4/2BK Polyethylene, 1/4” OD, Black (Per Foot)
TP-4/2NA Polyethylene, 1/4” OD, Natural (Per Foot)
TP-4/2OR Polyethylene, 1/4” OD, Orange (Per Foot)
TP-4/2YW Polyethylene,1/4” OD, Yellow (Per Foot)
TP-6/4BK Polyethylene, OD, Black (Per Foot)
TP-6/4NA Polyehtylene, 3/8” OD, Natural (Per Foot)
(Per foot)
(Per Foot)
(Per Foot)
(Per Foot)
(Per Foot)
(Per Foot)
27d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
VINYL (PVC) TUBINgPlasticized from nontoxic Flexible Vinyl PVC, this tubing offers a wide range of chemical resistance which makes it an ideal choice for a variety of industrial piping problems involving the handling of corrosive, pure or sensitive solutions.
Heat Shrinkable Tubing. Call for Details.
Durable overbraiding for extra protection against abrasion, mildew and aging for cable assemblies. This tubing is de-signed with an open-weave braided type construction, it offers flexibility and freedom of movement to the sleeving and wiring it covers. This open-weave construction allows complete drainage to prevent any moisture and condensation to cause any permanent damage to the inner wire it covers. Normal operating temperature range is -70°C to 125°C (-94°F to 257°F).
BRAIDED SLEEVINg
Please call and inquire on Apex Instruments extensive line of tubing.
TV- o/ o o
- o (Tube OD) / o (Tube ID) o (Color; R=red, Y=yellow)
TV-4/2 Vinyl, 1/4” OD, 18” ID, (Per Foot)
TV-5/3 Vinyl, 5/16” OD, 3/16” ID, Clear (Per Foot)
TV-5/3R Vinyl, 5/16” OD, 3/16” ID, Red (Per Foot)
TV-5/3Y Vinyl, 5/16” OD, 3/16” D, Yellow (Per Foot)
EXP- o - o (Diameter)
EXP-2 EXPANDO,1/8” Diameter Relaxed, Black
EXP-8 EXPANDO, 1/2” Diameter Relaxed, Black
EXP-12 EXPANDO, 3/4” Diameter Relaxed, Black
EXP-20 EXPANDO, 1.25” Diameter Relaxed, Black
EXP-30 EXPANDO, 2” Diameter Relaxed, Black
EXP-30HD EXPANDO, 2” Diameter Relaxed, Heavy Duty, Black
DgM-AP25DgM-110
DgM-175DgM-S275
DRY gAS METERS
Product Description
DGM-AP25 AP25 Metric Dry Gas Meter, used in MC-572 and MC-623
DGM-110 110 Rockwell Dry Gas Meter with 1/2” FNPT Side Ports, used in MC-522
DGM-175 175 Rockwell Dry Gas Meter with Top Mount Spud Connectors
DGM-S275 S-275 Gas Meter with 3/4” FNPT Side Port
DTM-P4B Dry Gas Meter Bushing, for use on old UL and new AP25 DGM’s only
DTM-P6B Dry Gas Meter Bushing, for use on old UL and new AP25 DGM's only
Special Purpose HoseThe Apex Instrumens Air hose is constructed of a PVC/Poly-urethane alloy, this hose has a high tensile strength yarn. The core tube has an excellent cut resistance. It also has a highly abrasion-resistant alloy jacket and has good flexibility over a wide temperature range of -20°C to 85°C (0°F to 185°F).
POLYSPRINg HOSEApex Instruments Polyspring hose is constructed of a clear PVC which allows the visual confirmation of product flow. The hose is resistant to chemicals and has a spiral wire reinforcement to prevent kinking or collapsing. The hose diameter will not expand under normal rated working pressures. It’s temperature range is -4°C to 65°C (25°F to 150°F). Used on our U-cords.
AIR HOSE
H- oSP - o (Diameter)
H4SP PVC/Polyurethane Alloy Air Hose,1/4” ID, Special Purpose, Blue (Per Foot)
H6SP PVC/Polyurethane Alloy Air Hose, 3/8”ID, Special Purpose, Blue (Per Foot)
H-oSPS - o (Diameter)
H-10SPS PVC, Clear, Reinforced with Helically-Wound Spring Steel Wire, 3/8” ID (Per Foot)
TUBINg
MPT-�-� MPT - � (TUBE OD) -� (LENgTH in MM)
MPT-6-133 Used for Oversheath Probes
MPT-6-181 Used for Method 5 Probes
MPT-6-218 Used for SFA-47
MPT-6-283 Used for PM10 and SFA-47
MPT-6-320 Used for SFA-190, SFA-300 and SFA-2590
MPT-6-421 Used for PM10-2.5 and SFA-47
The unique design of the Apex Modular Pitot Tip reduces amount of water droplets collected in the pitot lines. The lower tube is self-draining while the offset in the upper tube acts as a water trap. The water can be easily cleared tilting tip down or back. Replacement tips for standard Method 5 probes are MPT-6-181, and MPT-6-133 for probes with optional over-sheath. Longer tips are available for in-stack filtration. See Flow, Pressure and Temperature Section of this catalogue for additional pitots plus pipe flanges and inclinometers.
REPLACEMENT PITOT TIPS
STAINLESS STEEL, 3/8” TUBINg
length in mm
Standard M5 Probe: PA-��-�
(Per Foot)
28d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
AM3101A-K
AM-MCPAM3108S
AM3057
AM3106B-K
AM-SBP
AM3057
AM3102P
Displays- Thermocouple and Process:
TC-765-KF Temperature Display, LED, 120/240V, 1/8 DIN
205-EV-4RCO Process Meter Display, 5V, with Excitation Output, 3/36” DIN
205-PV-3RCO Process Meter Display, 5V, 3/64” DIN
Electrical Cordsets, Plugs and Jacks:
M-IEC-14AWG Power Cordset with 5-15P plug and IEC connector, 14 AWG
L5-15 NEMA 5-15 Plug, 15A/125V, 2-Pole, 3-Wire Grounding
L5-30 NEMA 5-30 Plug, 30A/125V, 2-Pole, 3 Wire Grounding
L6-20 NEMA 6-20 Plug, 20A/250V, 2-Pole, 3-Wire Grounding,
M-SCKT15A IEC Power Inlet, Screw Mount, 1/4” tabs, EAC-311, 15A/240V
M-49BK Snap-in Receptacle, NEMA 5-15R, Standard NA Type, 3-Pole, 1/4” Tabs, 15A/125V
Fans:
AM-CF110 Cooling Fan Axial, 120 Volt, 4.7” Square Axial
AM-CF220 Cooling Fan Axial, 240 Volt, 4.7” Square Axial
Switches:
M-31302A 7 Channel Thermocouple Switch
M-31302K 7 Channel Switch Knob
M-RA911 Rocker Switch (Curvette), SPST
M-4X846 Toggle Switch (On/Off), SPST
Heaters:
AM-SB500W Heater Element for Sample Box, 120V, 500 watts
AM-SB500W-220 Heater Element for Sample Box, 240V, 500 watts
AM-SB772W Heater Element for Sample Box, 120V, 772 watts
Pressure Transducers:
LPM1010-6B5 Druck Transducer, LPM1010 Series, 2in H20, 5 +/- 5 VDC Output, +/- .25% Accuracy, Terminal Strip
LPM1010-2B5 Druck Transducer, LPM1010 Series, 6in H20, 5 +/- 5 VDC Output, +/- .25% Accuracy, Terminal Strip
Solenoids:
M-U8356-120V ASCO 3-Way Solenoid, Brass, 120V
M-U835B-220V ASCO 3-Way Solenoid, Brass, 220V
Solid State Relays:
SSR-330-25 Solid State Relay, 25 AMP, 110/240V
SSR-330-40 Solid State Relay, 45 AMP, 110/240V
Video Inspection:
W7800 Monitor, leather case, power supply, P&T camera, star holder, 20m/65’ cable
Thermal Circuit Breakers:
M-CB15A Circuit Breaker, 15 AMP, 120/240 Volt
M-CB10A Circuit Breaker, 10 AMP, 120/240 Volt
M-CB3A Circuit Breaker, 3 AMP, 120/240 Volt
M-CB5A Circuit Breaker, 5 AMP, 120/240 Volt
Magnetic Circuit Breakers:
M-CBR15A-M Circuit Breaker, Magnetic, Rocker Switch, 15 Amp. Horizontal Mount., 120/240 Volt
M-CBR10A-M Circuit Breaker, Magnetic, Rocker Switch, 10 Amp. Horizontal Mount., 120/240 Volt
M-CBR5A-M Circuit Breaker, Magnetic, Rocker Switch, 5 Amp. Horizontal Mount., 120/240 Volt
M-CBR3A-M Circuit Breaker, Magnetic, Rocker Switch, 3 Amp. Horizontal Mount., 120/240 Volt
Electrical/Electronic Parts
Replacement Manometers & Parts:
M-42210 Dual Column Panel Mount Manometer, 0-10” H2O
M-42210-M Dual Column Panel Mount Manometer, 0-250mm, Metric
M-422DS Manometer Displacer with Knob
A-316 Manometer Bushing,1/8” FNPT, NY
DWA101R Red Manometer Oil
QC-MAN-F3 Manometer Quick Connect Fitting, 1/8” FNPT, Chrome plated Brass with Valve and Viton® O-ring
QC-MAN-M2 Manometer Quick Connect Fitting,1/4” MHB
PMC30 Manometer Quick Connect Plug
4T827 Retaining Cord, Quick Connect Plug Temperature Controllers:M-1400 Analog , 1/16” DIN, Type KM-PXR3-C Fuji Controller, 1/32” DIN, Degree Celsius
Circular Connectors (Amphenol) 4-pin
AM-SBP Filter Box Amphenol Wired Sub-Assembly
AM-MCP Replacement Meter Console Wired Amphenol Sub-Assembly
AM3101A-K Replacement Amphenol Connector for Apex U-cords, Male, 14S-2 Series, 4 Pin with external male threads, Teflon tubing, heat shrink
AM3106B-K Replacement Amphenol Connector for Apex U-cords, Female, 14S-2 Series, 4 Socket with swivel ring, Teflon tubing, heat shrink
AM3102P Replacement Amphenol Connector for Filter Box, Panel Mount
AM3057 Replacement Strain Relief for Amphenol
M-1400
PMC30 with 4T827
DWA101-RManometer Oil
29d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
Tube To Male Pipe
Male Connectors
2MSC2N-S 1/8TU-1/8MNPT4MSC2N-S 1/4TU-1/8MNPT4MSC4N-S 1/4TU-1/4MNPT4MSC6N-S 1/4TU-3/8MNPT6MSC6N-S 3/8TU-3/8MNPT8MSC6N-S 1/2TU-3/8MNPT 10MSC6N-S 5/8TU-3/8MNPT 10MSC8N-S 5/8TU-1/2MNPT
Male Elbow
4MSEL2N-S 1/4TU-1/8MNPT 4MSEL4N-S 1/4TU-1/4MNPT 4MSEL6N-S 1/4TU-3/8MNPT 6MSEL4N-S 3/8TU-1/4MNPT 6MSEL6N-S 3/8TU-3/8MNPT 6MSEL8N-S 3/8TU-1/2MNPT 10MSEL6N-S 3/8TU-3/8MNPT10MSEL8N-S 3/8TU-1/2MNPT
Thermocouple Connectors
8MTC8-S 1/2TU-1/2MNPT 16MTC16N-S 1.0TU-1.0MNPT
Male Branch Tee
4MBT4N-S 1/4TU-1/4MNPT 6MBT4N-S 3/8TU-1/4MNPT
Male Run Tee
4MRT4N-S 1/4TU-1/4MNPT 6MRT4N-S 3/8TU-1/4MNPT
Tube to Tube Unions
2SC2-S 1/8” Tube Union 4SC4-S 1/4” Tube Union 6SC6-S 3/8” Tube Union 8SC8-S 1/2” Tube Union N-10UB 5/8” Tube Union
4RU2-S 1/4TU-1/8TU 6RU4-S 3/8TU-1/4TU 8RU6-S 1/2TU-3/8TU
4EE4-S 1/4TU-1/4TU6EE6-S 3/8TU-3/8TU 8EE8-S 1/2TU-1/2TU
4ET4-S 1/4TU 6ET6-S 3/8TU
Jump Tee
6-6-4ET-S 3/8x1/4x3/8 Jump 8-4-6ET-S 1/2x1/4x3/8 Jump
Tube to Female Pipe
Female Elbow
4FEL2N-S 1/4TU-1/8FNPT
Female Run Tee
4FRT2N-S 1/4TU-1/8FNPT6FRT4N-S 3/8TU-1/4FNPT
Order Sizesin OrderShown inDiagram
1 2
3
Port Connectors
Tube End Reducer
4TUR6-S 1/4TU-3/8TU, 6TUR4-S 3/8TU-1/4TU, 8TUR10-S 5/8TU-1/2TU, 8TUR4-S 1/2TU-1/4TU, 8TUR6-S 1/2TU-3/8TU, 10TUR6-S 5/8TU-3/8TU,
Tube End Bulkhead Adapter
4TUBC4-S 1/4TU-1/4STUB 8TUBC8-S 1/2TU-1/2STUB
Port Connector
4PC4-S 1/4” 4PC6-S 1/4-3/8 6PC6-S 3/8” 6PC8-S 1/2-3/8
Tube End Male Adapter
6MA2N-S 3/8MT-1/8MNPT 6MA4N-S 3/8MT-1/4MNPT
1 2
STAINLESS STEEL FITTINgS
4NU-S 1/4” Tube Nut 6NU-S 3/8” Tube Nut 8NU-S 1/2” Tube Nut N-10 5/8” Tube Nut 12NU-S 3/4” Tube Nut
4BLEN4-S 1/4 Cap6BLEN6-S 3/8 Cap8BLEN8-S 1/2 Cap 10BLEN10-S 5/8 Cap
Cap Tube Nut
Other
Union Tee Union Elbow
Union Reducing Union
30d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
QUICK CONNECTS
CABINET LATCHCabinet Latch, Spring.m-hc8l
CABINET KEEPERSLatch Keeper, Long Shank for Hot Box Door.m-hS14lS
HARDWARE
CABINET KEEPERSLatch Keeper, Short Shank for Source Sam-pling Console Door.m-hS83K
SPRINg HANDLEStainless Steel Internal Spring Handle for Source Sampler Console, 3 Hole.h50032
PANEL LATCHPanel Latch, Slotted.l-43144
RUBBER FOOTRecessed Rubber Foot.9540K59
SAFETY BAILSafety Bail for Monorail Attachment.SB-2pin
RAIL HANgERRail Hanger for Source Sampler Console (Price per Pair).mc-rh
FEMALE TUBE END
QC-F4-SS Female TE, 1/4 IN - 1/4 TUQC-F6-SS Female TE, 3/8 IN - 3/8 TUQC-F8-SS Female TE, 1/2 IN - 1/2 TU
FEMALE BULKHEAD
QC-BHF4-SS Female BH, 1/4 IN - 1/4 TUQC-BHF6-SS Female BH, 3/8 IN - 3/8 TUQC-BHF8-SS Female BH, 1/2 IN - 1/2 TU
MALE TUBE END
QC-M4-SS Male TE, 1/4 IN - 1/4 TUQC-M6-SS Male TE, 3/8 IN - 3/8 TUQC-M8-SS Male TE, 1/2 IN - 1/2 TU
MALE BULKHEADQC-BHM4-SS Male BH, 1/4 IN - 1/4 TUQC-BHM6-SS Male BH, 3/8 IN - 3/8 TUQC-BHM8-SS Male BH, 1/2 IN - 1/2 TU
M-422DSA-316
MANOMETER QC FITTINgManometer Quick Connect Fitting, 1/8 FNPT, Chrome plated Brass with Valve & Viton® O-Ring.Qc-man-F3
MANOMETER QC FITTINgManometer Quick Connect Fitting, 1/4 MHB.Qc-man-F2
Apex Instruments offers many types of Stainless Steel Quick Connects. Brass is available for some types, please call for details.
All stoppers are rubber sleeve standard.
GS-13 13mm, 10/pk.GS-20 20mm, 10pkGS-30 30mm, 10/pk.GS-MIX Kit Includes: 10pk. each size
gS-13
gS-20 gS-30
Stoppers
GA-GL-18/10T #18 Silicone Seal Ring, with PTFE 9 mm to 11 mm
Seal ring
31d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
ADI-19319TTM ADI Single Heated Head Diaphragm-Vac Pump, SS Wetted Parts, 75W Heater Cart., Type K Thermocouple, 120/240V
GP-DAA-V142 Gast Model DAA Double Diaphragm Replacement Pump (100/120V-50/60Hz)
GP-DAA-V140 Gast Model DAA Double Diaphragm Replacement Pump (200/240V-50/60Hz)
GP-DAA-RBK Rebuild Kit for Gast Model DAA Double Diaphragm Pump
GP-15D1 Gast Model Mini Diaphragm Pump, 6.4 lpm open, 120VAC
GP-15D1-V Gast Model Mini Diaphragm Pump, 6.4 lpm open, 120VAC, 240V
GP-MAA Gast Model Double Diaphragm, MAA Series, Oiless, 120V
GP-MAA-V Gast Model Double Diaphragm, MAA Series, Oiless, 240V
AA404 Muffler Jar Seal, Replacement for Seal in Muffler Assembly (AB609B)
AB609B Muffler Assembly with 1/4 inch FNPT, for Vane Pump Assembly (GP-0523)
AJ-0523 Aluminum Muffler Jar, Replacement for Jar in Muffler Assembly (AB609B)
AJF-0523 Muffler Filter Insert, Replacement for Filter in Muffler Assembly (AB609B)
AK731 Gast Replacement Vanes for Pump Model GP-0523 (4 Required per Pump)
GP-BL50-2 Miniature Lubricator Assembly with 1/4 inch FNPT, for Vane Pump Assembly (E-0523)
GP-BL50-R Lubricator Rebuild Kit, Includes Wick, Nut, Grommet & Seal, for GP-BL50-2 Lubricator
GP10W-250 Gast Vane Pump Oil, 10W, 250mL
O-026N Lubricator O-Ring for BL-50-2. 0.026” Diameter
PUMPS & ACCESSORIES
Peristaltic Pumps are useful in a variety of applications. The material to be pumped only comes in contact with the tubing. This is ideal for applications where the product to be moved or pumped should not touch any foreign materials. Also, peristaltic pumps are precision flow rate devices with each revolution of the roller assembly delivering a precise amount of gas. Finally, peristaltic pumps are self-priming and can handle a wide variety of viscosities, from air to gases to heavy slurries. Economically priced fixed-flow peristaltic pumps are available for a wide range of flows. The single head pump PP907-049 comes with a tube kit consisting of four different pump tubes for adjusting the flow from 0.21 to 3.5 ccm per revolution. Different motor speeds are available from 2 to 203 rpm. The pump head and enclosure are made of polypropylene. Dual head model also available PP927-049 which is pre-set for 98 ccm per head.
DIAPHRAgM PUMPS
PERISTALTIC PUMPS
Single-Speed, Single-HeadPeristaltic Pump, 49 rev/min,with Tube Kit.pp907-049
Single-Speed, Single-Head Peristaltic Pump, 49 rev/min, with Tube Kit.pp927-049
LUBRICATED ROTARY VANE PUMPGast Model 0523 Lubricated Vane Replacement Pump (100/240V-50Hz/60Hz). gp-0523...$478.00
REPLACEMENT PARTS FOR ROTARY VANE PUMP
gASTGast Model Mini Diaphragm Pump, 6.4 lpm open, 120VAC.gp-15D1
240VACgp-15D1-V
KNFDiaphragm Vacuum Pump, KNF Model UN815KN, free flow 15 lpm, Ryton Head, EPDM Diaphragm and valves, 120VAC/50 Hz.gp-un815Kn
DIAPHRAgM PUMPS
Single, Dual and Triple Head Peristaltic Pump Assembly (150 volt, 6 RPMs with Cooling Fan).pp-7015a-epp-7015a-e2pp-7015a-e3
32d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
Antiseize, 1/4 oz. Tube, -65°F to 2600°F
EQUIPMENT CASES
ATA Transport Cases protect your equipment and glassware from shipping damage. Each case is made of sturdy 3/8” ABS laminated plywood with reinforced edges and corners. A built-in foam liner provides added protection. Call for details on custom cases.
ATA Transport Cases
Part # DimensionsTC-0523 Console Transport Case - Pump UnitTC-0523C Console Transport Case Enclosure - Pump UnitTC-522 Console Transport Case - MC-500 Series Source Sampler ConsolesTC-522U Console Transport Case - MC 500 Series Source Sampler
Consoles with Extra StorageTC-600 Console Transport Case - MC-170 & MC-623 Source
Sampler ConsolesTC-7A9 Method 7 Kit Transport CaseTC-GW2.5 Glassware Transport Case (holds 2-1/2 sets of Method 5 Glassware)TC-GW20I ATA Glassware Transport Case (holds 20 impingers)TC-PITOT Blow Molded Case with Convoluted foam, locking metal latchesTC-SB13 Sample Case Transport Case (Holds One SB-2 & Two SB-3 Units)TC-VSB VersaCase Transport Case (Holds any VersaCase2 Kit Method)TC-X0523 XC Pump Unit Transport CaseTC-XC5 XC-500 Series Pump Unit Transport Case
Apex Instruments now offers multiple black plastic, stackable SKB RotoRack cases to protect your equipment from damage. Constructed of a molded polyethylene shell which includes front and rear covers and gasket seals to protect the contents from moisture and dirt. This case offers recessed heavy duty twist latches, molded in handles and shock absorbing rubber feet. (optional rear rails available for added stability). Call for pricing.
SKB Cases
Part # DimensionsXC-5U Black RotoRack Case - Shallow 19”; 5
Unit, Inside HxWxD: 19” x 8” x 8.75”,Black Polyethylene
XC-6U Black RotoRack Case 19” Rotomolded Rack Case, 6U, Black Polyethylene
XC-8U Black RotoRack Case - HxWxD: 18” x 22” x 20”; 21 lbs.
XC-10U Black RotoRack Case - Shallow 19”; 10 Unit, Inside HxWxD: 19” x 17-1/2” x 8”, UHMW black polyethylene.
XC-10UD Black RotoRack Case - HxWxD: Outside 20.5” x 23.75” x 22”; 20.46 lbs.
XC-16US Black Shock Mount Rack Case - HxWxD: 36.25” x 29.25” x 27.25”; 84 lbs.
SKB-1916 Rotomolded Castorboard, w/3-inch locking wheels for 16U Rack Case Transport.
TC-0523
TC-gW2.5
TC-X0523
SUPPLIES
TFE HIgH DENSITY TAPETFE Tape, High Density, 1/2” X 520” per roll.T-TFe8-520
TFE Tape, High Density, 1” X 520” per roll.T-TFe16-520
TFE Tape, High Density, 2” X 520” per roll.T-TFe32-520
ANTI-SEIZE PREMIUM gRADE NICKEL BASED,Anti-seize, 1/4 oz. Tube, -65°F to 2600°F.aZni-4
3M gLASS ELECTRICAL TAPE3M Glass Electrical Tape, 69, 3/4” x 108’ per roll.3m-108
XC-8U Transport Case XC-10UD Molded Rack Case
XC-16US Molded Rack Case
33d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
MONORAILS
MONORAIL HARDWARE
(Threaded pipe flanges are available in 3”, 4” or 6”, stainless steel or aluminum.) Note: The chain must be attached to the stack so that the chain angle to the monorail is no less than 30° (45° is recommended).
PF- CSPipe Flange
PART # Monorail with Cable and Chain LF
P1001-10 MONORAIL, 10FT, STEEL Heavy Duty, Double Channel, W/CHAIN, L-Bracket & Hardware.
10
P1001-12 MONORAIL, 12FT, STEEL Heavy Duty, Double Channel, W/CHAIN, L-Bracket & Hardware.
12
P1001-14 MONORAIL, 14FT, STEEL Heavy Duty, Double Channel, w/ Adjustment Chain, L-Bracket & Hardware.
14
P1001-16 MONORAIL, 16FT, STEEL Heavy Duty, Double Channel, w/Cable, Adjustable Strap, L-Bracket & Hardware.
16
P1001-17 MONORAIL, 17FT, STEEL Heavy Duty, Double Channel, w/Cable, Adjustable Strap, L-Bracket & Hardware.
17
P1001-18 MONORAIL, 18FT, STEEL W/CHAIN Heavy Duty, DoubleChannel, w/Cable, Adjustable Strap, L-Bracket & Hardware.
18
PART # Flange
PF-3CS Flange, 3” 150 lb. FF, 2.67 Bored, Stainless Steel, with Threaded Coupling.
PF-4CS Flange, 4” 150 lb. FF, 2.67 Threaded, Stainless Steel, with Threaded Coupling.
PF-6CLS Flange, 6” 150 lb. FF, 2.67 Bored, Stainless Steel with Cam-lock Connector.
See Accessories Section for Different Configurations.
PART # Trolley and Monorail Support Bracket
P2751 MONORAIL, TROLLEY Swivel Frame Trolley with Eyebolt, 1 Foot Chain and Snap-hook.
P501 MONOMOUNT, MONORAIL SUPPORT Support Bracket; Fits 3”, 4”, 6” & 8”, Standard Pipe Flanges, Includes P1354 Hinge, (4) P3010 Nuts and P371 Bolts.
Link to Flanges
LF 6 7 8 9 10 12
Part # P1000-6 P1000-7 P1000-8 P1000-9 P1000-10 P1000-12
Probe Size
For use with probes over 6’
For use with probes over 7’
For use with probes over 8’
For use with probes over 9’
For use with probes over 10’
For use with probes over 12’
monorail with chainHeavy Duty Steel Monorail with Chain, L-Bracket and Hardware (for use with probes).
34d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
PART # Flange
PF-3CS Flange, 3” 150 lbs. FF, 2.67 Bored, Stainless Steel
PF-4CS Flange, 4” 150 lbs. FF, 2.67 Threaded, Stainless Steel
PF-6CLS Flange, 6” 150 lbs. FF, 2.67 Bored, Stainless Steel with Cam-lock Connector
PART # Trolley and Monorail Support Bracket
P2751 Monorail, Trolley Swivel Frame Trolley with Eyebolt, 1 Foot Chain and Quick Link
P501 Monomount Monorail Support Bracket; Fits 3, 4, 6 & 8”, Standard Pipe Flanges, Includes Hinge, Nuts, and Bolts
Training Manuals
MANUALS AND REFERENCE MATERIALApex Instruments offers a complete line of Title 40 of the Code of Federal Regulations that pertain to Protection of the Environ-ment. Title 40 is composed of twenty-eight volumes of which Air Programs comprises approximately sixteen. The most popular for our customers are Part 60 (60.1-end) Standards of Performance for New Stationary Sources and Part 60 (Appendices) that include only the US EPA Source Testing Methods. Please call or check our Price List for detailed listing of all Title 40 volumes.
Training Manuals
Code of Federal Regulations
Part # Description
40CFR-SET Set, CFR 40, AIR/RCRA PROGRAMS, 19/Set (1 ea. listed below)
40CFR1-49 CFR 40, Parts 1-49 (Air Programs)
40CFR50-51 CFR 40, Parts 50-51 (Air Programs)
40CFR52A CFR 40, Parts 52.01-52.1018 (Air Programs)
40CFR52B CFR 40, Parts 52.1019-52 END (Air Programs)
40CFR53-59 CFR 40, Parts 53-59 (Air Programs)
40CFR60 CFR 40, Parts 60.1-END (Air Programs)
40CFR60APPX CFR 40, Part 60 APPENDIX (Air Programs)
40CFR61-62 CFR 40, Parts 61-62 (Air Programs)
40CFR63A CFR 40, Parts 63.1-63.599 (Air Programs)
40CFR63B CFR 40, Parts 63.600-63.1199 (Air Programs)
40CFR63C CFR 40, Parts 63.1200-END (Air Programs)
40CFR64-71 CFR 40, Parts 64-71 (Air Programs)
40CFR72-80 CFR 40, Parts 72-80 (Air Programs)
40CFR81-85 CFR 40, Parts 81-85 (Air Programs)
40CFR86A CFR 40, Parts 86.1-86.599-99 (Air Programs)
40CFR86B CFR 40, Parts 86.600-END (Air Programs)
40CFR190-259 CFR 40, Parts 190-259 (RCRA)
40CFR260-265 CFR 40, Parts 260-265 (RCRA)
40CFR266-299 CFR 40, Parts 266-299 (RCRA)
Product Manuals
MONORAILS
35d www.apexinst.com 800-882-3214 /919-557-7300
ACCESSORIES
Data Reduction Software
Product Description
PM-2.5-10C Particle Sizing Software for PM2.5 and PM10 Cyclones
ISOCYCLONE1.0 PM10/2.5 IsoCyclone Data Collection and Reduction Spreadsheet (MS Excel Workbook)
ISOCALC2.2 Isocalc Data Collection and Reduction Spreadsheet (MS Excel Workbook). Method 1-5
PARTICLE SIZINg DATA REDUCTION SOFTWARE
Functions• Calculates each stage’s aerodynamic cut point and DP250, needed to reduce particle size data. • Calculates and Stores ancillary data, such as dry gas composition and moisture content. • Reduces velocity traverse data. • Aids in selection of sample flow rates and ideal nozzle size. • Calculates flow rates and dwell times required for PM10 and PM2.5 sampling traverses. • Calculates fractional efficiencies of control devices from samples obtained at inlets and outlets.
WinciDrS
Windows-based Cascade Impactor Data Reduction System (WINCIDRS) calculates particle size distribution of stack particulate matter (PM) taken with the Cascade Impactor, as well as particle-sizing cyclones. Developed by stack particle analysis experts, this software reduces the time and chances of error involved with reducing particle sizing data. The PM10/2.5 Software Program (PM-2.5-10C) is extracted from WinCIDRS and simplified for use only with PM10 and PM2.5 cyclones. The calculations are similar to the WinCIDRS, scaled-down specifically for cyclone data reduction. The calculations are still intensive enough to demand computer software.
Isokinetic Slide RuleThis device performs Isokinetic Stack Sampling Calculations. The slide rule provides new ∆H settings at a glance.
m5a-1.......english units
m5a-1m....metric units
ISOKINETIC CALCULATORS & SPREADSHEET
Programs included: • Traverse Points Location• Stack Gas Velocity and Volumetric Flow Rate• Stack Gas Moisture Content• Stack Gas Saturation Moisture Content• Ideal Nozzle Size and K-Factor with ∆H Loop• Post-Test Isokinetics• DGM Field Calibration using Critical Orifices
m5a-c
M5A-C
Isokinetic M5A-C CalculatorThe Casio Graphic Scientific Calculator comes pre-programmed with valuable Isoki-netic stack sampling calculations making field calculations quick and easy. Programmed in English and metric units. M5A-1
36d 800-882-3214 /919-557-7300 www.apexinst.com
ACCESSORIES
Alumina....................................................... 19dBalances ..................................................... 16d-17dBushings ..................................................... 20d-21dCam-Lock, Flanges, Port Adapters & Packing Glands ....................................... 20d-21dCouplings.................................................... 20d-21d Components List, XC-522 / XC-572 ........... 10dDessicator & Dessicants............................. 18dDrierite Dessicants ..................................... 19dDrierite Dessicants ..................................... 20dDry Gas Meter Calibration Services ........... 22dDry Gas Meters .......................................... 27dElectrical/Electronic Parts ........................... 28dEquipment Cases ....................................... 32dFilter Media ................................................. 11d-12dFlange Reducers ........................................ 20d-21dFlow Adapters ............................................. 25d-25dHardware .................................................... 30dHose, Air ..................................................... 27dHose, Polyspring ........................................ 27dInclinometers .............................................. 25dIsokinetic Calculators & Spreadsheets ....... 34dManometers................................................ 23dManuals & Reference Materials ................. 34dMeter Calibration Equipment & Services .... 23dMeter Calibration Equipment & Services .... 23dMonorails .................................................... 33dMonorail Accessories.................................. 34dManometers................................................ 23dMercury, Spare Parts .................................. 3d-9dMercury, Console & Spare Parts ................ 3d-9d
Accessories
Mercury, Probes ......................................... 3d-9dMercury, Coolers ........................................ 3d-9dMercury, Probe Accessories ....................... 3d-9dOrifice Flow Meters ..................................... 24dParticle Sizing Data Reduction WINCIDRS Software .................................. 34dPFA Column Components .......................... 15dPFA Impingers & Accessories..................... 15dPFA Stems & Fittings .................................. 15dPFA Filter Assemblies ................................. 15dPitot Audit Equipment ................................. 23dPitot, Replacement Tips.............................. 27dPumps & Accessories ................................. 31dQuick Connects .......................................... 30dRotometers ................................................. 24dSample Recovery ....................................... 13dSample Recovery Accessories ................... 14dSample Recovery Bottles ........................... 14dSilica Gel .................................................... 19dStainless Steel Fittings ............................... 29dSupplies, Tape ............................................ 32dTubing, PTFE ............................................. 26dTubing, PFA ................................................ 26dTubing, PFA Stainless Steel Overbraid ...... 26dTubing, Stainless Steel ............................... 26d-27dTubing, Polyurethane ................................. 26dTubing, Polyethylene .................................. 26dTubing, PVC ............................................... 27dTubing, Braided Sleeving ........................... 27d
TERMS AND CONDITIONS
PRICES AND TERMSOur prices are subject to change without notice. The price in effect when we receive your order will apply. All prices are Ex Works Holly Springs, North Carolina. We will be pleased to furnish quotations by phone, fax or e-mail. Terms of payment are Net 30 days with established credit, or by Visa/MasterCard/American Express at time of order. Invoices over 30 days past due are subject to 1.5% permonth finance charge.
CONFIRMINg ORDERSPlease make sure that all confirming orders are clearly marked to avoid duplicate orders.
SHIPMENTS AND DELIVERYUnless otherwise instructed, shipments are made as soon as possible after receipt of order by method of transportation which in our judgement will be most satisfactory. Freight charges are prepaid and added to the invoice. The right is reserved to make partial shipments where delays beyond our control may delay a portion of the order.
EXPORT PROCESSINg AND PRICINgPrices do not include customs and duty charges, freight, insurance, export fees, bank wire transaction fees or any additional handling fees.
RETURNED ITEMSAuthorization must be obtained from us before returning any goods. When requesting return authorization, please advise reason for return, date of purchase, your P.O. number and our invoice number. Equipment produced to special specifications are not returnable. All returns must be shipped freight prepaid at the purchasers expense and are subject to a restocking fee.
LIMITED WARRANTYAPEX INSTRUMENTS, INC. warrants products to be free from defects in workmanship for a period of one year from date of delivery. The sole and exclusive remedy for defective goods shall be to repair or replace defective parts or payment price of the goods for which damages are claimed at APEX INSTRUMENTS, INC.’s option. Freight for return of defective items will be at the sole discretion of APEX INSTRUMENTS, INC. Except as described in our guarantee, there are no express warranties or implied warranties including, but not limited to, merchantability and fitness for a particular purpose. APEX INSTRUMENTS, INC. shall not be subject to and disclaims: (1) any other obligations or liabilities arising out of breach of contract or warranty, (2) any obligations whatsoever arising from tort claims (including negligence and strict liability) or arising under other theories of law with respect to products sold or services rendered by APEX INSTRUMENTS, INC., or any undertakings, acts or omissions relating thereto, and (3) all consequential, incidental and contingent damages whatsoever.
DESIgN CHANgESDesign changes are made from time to time. Some items may differ slightly from catalog illustrations or descriptions. Changes are made in the interest of better performance and quicker delivery.
ACCEPTANCE OF TERMS AND CONDITIONSAPEX INSTRUMENTS, INC. sells products only under foregoing terms and conditions and will not be bound to terms and conditions stated by any purchaser in any offer, acceptance or other contractual document. Placing an order or accepting delivery of products constitutes acceptance of terms and conditions.
Great care has been taken in preparation of this literature, however, we cannot be responsible for any omissions or typographical errors.
204 Technology Park LaneFuquay-Varina, North Carolina 27526, U.S.A.
Telephone: 919-557-7300In U.S. Call: 800-882-3214
Fax: 919-557-7110Email: [email protected]
apex inSTrumenTS, inc.Solutions for Source Sampling EquipmentApex Instruments is a world leader in the manufacture, design and distribution of source sampling equipment. Our products are used in a wide variety of sampling scenarios. Our equipment complies with emissions measurement standards for stationary combustion sources in accordance with US EPA guidelines. We are located approximately 20 miles from the United States Environmental Protection Agency in Research Triangle Park, N.C. Our goal is to provide you with the proper, well engineered equipment in order for your job to run smoothly and have consistent, accurate and reliable results.
Technical SerViceSApex Instruments understands the needs and high demands of the individuals working in the source sampling industry. The primary end users of our equipment consist of government agencies, consulting firms and private industries throughout North America and in 50 countries around the globe. Our knowledgeable staff includes many skilled industry professionals, stack testers and chemists. They all will help you to make important decisions regarding your specific application needs.
caliBraTion SerViceSApex Instruments offers dedicated, climate controlled, precision calibration services for a variety of measuring instruments. This includes gas meters, orifices and pitot tubes to help keep all your calibration equipment up-to-date. Our trained staff will utilize the reliable calibration equipment and tools such as NIST Certified Bell Prover wet test meters, electronic flow calibrators and wind tunnels. We offer a certification of calibration when requested.
cuSTom FaBricaTion anD aSSemBlYApex Instruments’ custom-designed facility was built in 2005. The warehouse layout provides a smooth flow for the assembly and fabrication departments. We can design, build and expedite all equipment orders quickly through our in-house engineering, production and welding departments. Apex continues with their steady commitment to quality in compliance testing, by consistently designing and developing reliable source sampling equipment. We folllow guidlines set by U.S. EPA Reference Methods and always keeping the genuine needs of the stack samplers in mind.
aWarDSApex Instruments recently received the (SHARP) Safety and Health Achievement Award from the NC (DOL) Department of Labor. This program recognizes small to medium size businesses that establish and maintain effective safety standards and health programs. We were also ranked in the top 500 by Inc. Magazine as being one of the fastest growing privately held companies.
www.apexinst.com
EquipmEntCatalog
Distributed by:
Publication:Date Issued:
PEC-Catalog1-01-12
GAS ANALYSIS
FLOW PRESSURE
ISOKINETIC
MERCURY
ACCESSORIES
Top Related