X5 Full-TOWER GAMING CASE

X10 Double/Full-TOWER GAMING CASE

User Manual

2

Contents

1.1 Specifications X5 3

1.2 Specifications X10 4

1.3 Accessory X5 & X10 5

1.4 Additional Accessory X10 5

2.1 Side Panel Disassembly 6

2.2 Motherboard Installation 7

2.3 5.25” Device Installation 8

2.4 External 3.5” Device Installation 9-10

2.5 2.5” HDD Installation 11

2.6 Power Supply Installation 12

2.7 Fan Installation 13-15

2.8 Water Cooling Installation 16

2.9 Supporting Feet Installation 17

2.10 Front I/O Installation Guide 18

3.1 Mini ITX Installation X10 19

3.2 Second Power Supply Installation X10 20

3

Chapter 1. Product Introduction

1.1 Specifications X5

Dimension 230（W）x 580（H）x 605（D）mm

Material SECC

Front Panel：ABS + Mesh Design

Device & HDD 5.25 '' X 4（Exposed）

2.5 '' X 4（Hot Swappable Tray）

3.5 '' X 6（Hot Swappable Tray）

3.5 '' X 2（Hidden）

Slot 10

Front I/O USB3.0×2+USB2.0×4+ HD Audio

LED Indicator Power & HDD

Cooling Fan Front：LED 120mm × 2 (included)

Rear：140mm × 1 (included)

Side：230mm x 1 or 120mm x 2 or 140mm x 2

Top: 230mm x 1 or 120mm x3 or 140mm x 2

Bottom: 230mm x 1 or 120mm x 2 or 140mm x 1

Motherboard ITX, mATX, ATX, E-ATX, XL-ATX, HTPX

Power Supply ATX

4

1.2 Specifications X10

Dimension 230（W）x 780（H）x 605（D）mm

Material SECC

Front Panel：ABS + Mesh Design

Device & HDD 5.25 '' X 6（Exposed）

2.5 '' X 4（Hot Swappable Tray）

3.5 '' X 8（Hot Swappable Tray）

3.5 '' X 2（Hidden）

Slot 10

Front I/O Main Case: USB3.0×2 +USB2.0×4 + HD Audio

Top System: USB2.0×2 + HD Audio

LED Indicator Power & HDD

Cooling Fan Main Case:

Front：LED 120mm × 2 (included)

Rear：140mm × 1 (included)

Side：230mm x 1 or 120mm x 2 or 140mm x 2

Top: 230mm x 1 or 120mm x3 or 140mm x 2

Bottom: 230mm x 1 or 120mm x 2 or 140mm x 1

Top System:

Top: 230mm x 2 or 120mm x 4 or 140mm x 3

Motherboard ITX, mATX, ATX, E-ATX, XL-ATX, HTPX

Power Supply ATX (Main System) + SFX (Top System)

5

1.3 Accessory X5 & X10

- User Manual x 1

- Supporting Feet x 2

- Cable Tie x 5

- Screw Bag container the following screws:

Standoff

5H-6#*4- 6#*6.5HCu

Screw

6*5KM

Screw

3*5KM

15PCS 32PCS 32PCS

Screw

M4*10

Screw Supply

6#6HW-TC

Screw

6#*5B-C

8PCS 8PCS 19PCS

1.4 Accessory X10

Cover for the I/O slot if not used

(Top System)

Switching cable for connecting

two ATX PSU to one motherboard

Three different back plates for the top system

6

Chapter 2. Installation Guide

2.1 Side Panel Disassembly

Remove the thumb screws from the rear side of the case and pull the

side panel rearwards.

To close again place the side panel into the guide rails and push it

forwards with care, then screw in the two thumb screws on the rear

side.

X10 only: To open the side panel of the top unit, push the two indented

handgrips inward to release the door.

7

2.2 Motherboard Installation

Install the I/O panel that comes with your motherboard package.

Secure the standoffs on the motherboard tray.

Install the motherboard in proper location and secure it with provided

screws.

NOTE:

CPU, RAM and any peripheral installation are not included in

this manual. Please refer to your motherboard manual for

related mounting instructions and troubleshooting.

8

2.3 5.25” Device Installation

From the interior of the case, use a firm device of your choice to push

the 5.25” drive bay cover out.

Place the 5.25” device into the drive bay.

Match the ODD drive holes with the drive cage. Then turn the knob

clockwise to secure the drive cage.

9

2.4 External 3.5” Device Installation

Open the front panel on the left hand side.

Remove the hard drive tray by pushing the tray tab to the right to

release the hard drive tray.

Install hard drive by placing each individually into the hard drive tray.

Secure each from the bottom of tray with the provided screws.

10

Place the tray back into to the case and lock it in place by pushing the

tray in. The rear of the hard drive will connect to the backplane.

Find the 4-Pin Molex on the power supply and connect it to the

backplane. Connect the backplane to motherboard with SATA cable.

X10 only:

There are two more HDD trays at the top of the case.

11

2.5 2.5” HDD Installation

Remove the 2.5” SSD hard drive tray by pushing the tray tab to the

right to release the tray.

Place 2.5” SSD hard drive into the hard drive box. Close the box.

Slide the 2.5” SSD hard drive box to the end of drive cage.

12

2.6 Power Supply Installation

Place the power supply in its proper location and secure it with the

provided screws.

Simply route the cables behind the motherboard tray and secure them

with the provided cable tie.

To optimize performance it is recommended that the washable dust

filter underneath the power supply be cleaned on a regular basis.

Simply pull out the dust filter, rinse with water, and slide it back after

the dust filter is dried.

13

2.7 Fan Installation

Fan Installation on the Side Panel

Take out the dust filter from the side panel.

Unscrew these three screws from the back of the side panel.

 

 

Pull the plastic cover backward to remove the cover

     

 

14

Install the fan on the inside of the side panel and secure it from the

outside of the panel with the provided screws.

Up to two 120mm or two 140mm or one 230mm (in both directions)

fans can be installed on the left side panel.

Pull out the washable dust filter from the side panel for regular

cleaning.

15

Bottom Fan Installation

User can install 120mm x2, 140mm or 230mm x1 on the bottom panel.

Top Fan Installation

Remove the screws on the back of chassis and open the top panel.

Install fans on the top and secure with the provided screws.

Up to 120mm x3, 140mm x2 or 230mm x1 can be installed on top.

X10only: Up to 120mm x 4 or 140mm x 3 or 230mm x 2 fans can be

installed in the top unit.

16

2.8 Water Cooling Installation

The pre-drilled water cooling holes at the case rear is for installing the

external water cooling system.

A 360 mm radiator may be installed on the top of chassis using the

pre-drilled screw holes.

     

X10only:

A 480 mm radiator may be installed on the top plate using the

pre-drilled screw holes.

17

2.9 Rubber Feet Installation

Install Rubber foot on the proper position.

Install supporting feet on the bottom with M4x10mm screws.

18

2.10 Front I/O Installation Guide

X10 only: The unit comes with two sets of front ports:

Please refer to the following illustration of front I/O connector and your

motherboard user manual.

USB 3.0

USB 2.0

HD Audio

Front I/O ports for Top System

Front I/O ports for Main Case

19

Chapter 3. Other Installation

X10 only : The full tower comes with three different rear panels to meet the

user’s various needs.

mini ITX back plate PSU back plate Fan back plate

3.1 Mini ITX Installation

Install the I/O panel that comes with motherboard package.

Install the power supply and the motherboard with the provided

screws.

20

22

3.2 Second Power Supply Installation

Unscrew and remove the rear panel from the back of the case.

Install the PSU back plate in the rear with the provided screws.

                

Install the power supply in the top unit.

Connect the two power supplies with the provided PSU switching

cable.

22

Streak Products, Inc. • www.ultraproducts.com

© 2013 Streak Products, Inc.

Ultra® is a registered trademark and Ultra ETORQUE™ is a trademark of Streak

Products, Inc.

8300 West Flagler Street, #121-106, Miami, FL 33144

All other trademarks listed are the property of their respective owners.

Streak Products is not responsible for typographical or photographic errors.

TECHNICAL SUPPORT (888) 222-5487

WARNING: Keep out of reach of children-contains sharp edges that may harm

children.