VERSA CURVE INSTRUCTOR DESK - Amazon S3...versa curve instructor desk assembly instructions nts4 of...

ASSEMBLY TEMPLATE

NOTE:

1. MODEL VIEWS MAY NOT REPRESENT EXACT MODEL PURCHASED

VERSA CURVE INSTRUCTOR DESK1314K, 1324K, 1334K, & 1344K SERIES

ASSEMBLY INSTRUCTIONS

REVISION LEVEL

EMK12/13/17CREATED DRAWING

REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE

REVISION:SCALE: SHEET:DRAWING NUMBER:

300 South Krueger StreetSuring, WI 54174

diversifiedwoodcrafts.comBY:APR

APR:DATE

CONFIDENTIAL:ALL DESIGN RIGHTS RESERVEDTHE INFORMATION, DATA, DESIGN, AND DRAWINGS EMBODIEDIN THIS DOCUMENT AND ALL REPRODUCTIONS THEREOF ARETHE EXCLUSIVE PROPERTY OF DIVERSIFIED WOODCRAFTS, INC. THESE DOCUMENTS ARE SUPPLIED WITH THE UNDERSTANDINGTHAT THEY WILL NOT BE DISCLOSED TO THIRD PARTIES WITHOUTWRITTEN CONSENT OF DIVERSIFIED WOODCRAFTS, INC. ANYREPRODUCTION IN PART OR WHOLE WITHOUT WRITTENCONSENT IS SUBJECT TO LEGAL ACTION.

ALL DIMENSIONS ARE IN INCHES UNLESSNOTED OTHERWISE

CABINET SQUARENESS = ± .0625FRACTIONAL VALUES = ± 1/32"

- ALL VALUES ± OVERALL -

1314K, 1324K, 1334K, & 1344K

VERSA CURVE INSTRUCTOR DESKASSEMBLY INSTRUCTIONS

REV A1 OF 13NTS

EMK 12/13/17

NAMEDATEDESCRIPTION ECN NO.

K:\AutoCAD\Assembly Instructions\1314K, 1324K, 1334K,

& 1344K SERIES.dwg, 4/21/2020 11:08:04 AM, DWG To PDF.pc3

ASSEMBLY TEMPLATE

NOTE:

1. **XX** INDICATES ITEMS USED ONLY FOR THE INSTRUCTOR'S DESKWITH A SINK.

1.1. EX. 1334K & 1344K2. COMPONENTS VARY WITH STYLE OF INSTRUCTOR'S DESK

PURCHASED.

REVISION LEVEL


REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE




APR:DATE





1314K, 1324K, 1334K, & 1344K

VERSA CURVE INSTRUCTOR DESKTOOLS AND ASSEMBLY COMPONENTS

REV A2 OF 13NTS

EMK 12/13/17


ASSEMBLY COMPONENTSITEMS INCLUDED PART # PART DESCRIPTION QTY

TOP - MAIN VARIESTOP,PHENOLIC,.75X24X72,BLK,(EITHER

FIXTURE OR FLAT) 1

TOP - CURVED 251629 TOP,PHENOLIC,.75X20.25X72,BLK,CUTOUT 1

TOP - LID 251630 TOP,PHENOLIC,.75X8.00X37.88,BLK,FLAT 1

TOP - BACKSPLASH 251628 TOP,PHENOLIC,.75X1.75X72,BLK,FLAT,CURVED 1

CABINETS N/A CABINET (STYLE VARIES) 18"W X 22"D X32.50"H 2

APRON N/A 0.81"THK X 4.50"W X 32"L 1

REMOVABLE PANEL N/A 0.75"THK X 32"W X 28.50"L 1

TOEKICK N/A 0.75"THK X 4"W X 32"L 1

SCREWS - REMOVABLE PANEL 100495 SCREW,#10X1-1/2 PHIL TR.SMS.ZN 6

SCREWS - MOUNTING CLEATS 100597 SCREW,#8.00X1.5 QUAD ROUNDWASHER 8

L BRACKET 100355 BRACKET,RAIL 1.25X1.25X4.25 2

SCREWS - L BRACKET 100649 SCREW,#8X34 PHIL TRUSS HEAD SMS 8

SILICONE 100711 SILICONE,SEALANT,CLEAR 2

RUBBER BASE MOLDING 100283 RUBBER BASE MOLDING (SOLD BY FOOT) 20

STAINLESS STEEL CORNERS 100057 CORNERS-STAINLESS STEEL,BASE 8

SCREWS - BASE 100064 SCREW,#6X12 PTH SMS SS SCREW 32

TOOLS REQUIREDCONTACT CEMENT

SCREW DRIVER

C-CLAMPSSHIM STOCK (IF NEEDED)



ASSEMBLY TEMPLATE

NOTE:

1. **XX** INDICATES ITEMS USED ONLY FOR THE INSTRUCTOR'S DESKWITH A SINK.

1.1. EX. 1334K & 1344K2. COMPONENTS VARY WITH STYLE OF INSTRUCTOR'S DESK

PURCHASED.

REVISION LEVEL


REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE




APR:DATE





1314K, 1324K, 1334K, & 1344K

VERSA CURVE INSTRUCTOR DESKTOOLS AND ASSEMBLY COMPONENTS

REV A3 OF 13NTS

EMK 12/13/17


ASSEMBLY COMPONENTSITEMS INCLUDED PART # PART DESCRIPTION QTY

ELECTRICAL BOX 100033 ELECTRICAL BOX 3.00X2X2.5 DEEP 3

ELECTRICAL OUTLET 100034 ELEC,OUTLET,GFI,20A 125V,BLK 1

ELECTRICAL RECEPTACLE 100031 ELECTRICAL DUPLEX RECEPTACLE 2

ELECTRICAL FACE PLATE 100774 ELECTRICAL,QUAD REC FACE PLATE,PL 1

TV LIFT 251615 TV LIFT. MOTORIZED 1

**FIXTURE - FAUCET** 100074-BKR FIXTURE,L65-WSA-DIV(MULTI-SERVICE) 1

**FIXTURE - SINK** 100692 SINK,EPOXY L5C,BLK 1

**FIXTURE - SINK TRAP** 100056 SINK TRAP,PLASTIC ADJUSTABLE 1

**FIXTURE - SINK STOPPER** 100112 SINK STOPPER 1 12, BLK 1

**FIXTURE - STRAINER** 100055 STINK,OUTLET/STRAINER EPOXY,BLK 1



ASSEMBLY TEMPLATE

REVISION LEVEL


REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE




APR:DATE





1314K, 1324K, 1334K, & 1344K


REV A4 OF 13NTS

EMK 12/13/17


STEP 1:

PLACE CURVED FRONT IN DESIRED LOCATION. LEVEL AND ATTACH TO FLOOR. IF YOUR INSTRUCTORS DESK HAS A TV, YOUR CURVED FRONT WILL HAVE

A LID ATTACHED TO TOP OF CURVED FRONT. IF YOU DO NOT HAVE A TV, YOUR CURVED FRONT WILL BE FLAT. IF YOUR UNIT HAS ELECTRICAL COMPONENTS IN CURVED PANEL, THEY

WILL NEED TO BE INSTALLED BEFORE ATTACHING CABINETS TO CURVEDPANEL. SEE SHEET 12 FOR DETAILS.

NOTE:

1. ALL WATER, ELECTRICAL, AND GAS CONNECTIONS SHOULD BEPERFORMED BY A TRAINED PROFESSIONAL PER LOCAL CODE.

CURVED FRONT

LID

FRAME SUPPORT - TYPICAL



ASSEMBLY TEMPLATE

REVISION LEVEL


REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE




APR:DATE





1314K, 1324K, 1334K, & 1344K


REV A5 OF 13NTS

EMK 12/13/17


STEP 2:

POSITION CABINETS AGAINST THE CURVED FRONT. MAKE SURE OUTSIDE OF CABINETS ARE FLUSH WITH OUTSIDE OF CURVED FRONT. ATTACH CABINETS TO CURVED FRONT BY GOING INSIDE CABINETS AND SCREWING THROUGH THE

MOUNTING CLEATS INTO THE FRAME SUPPORTS WITH SCREWS PROVIDED. BE SURE TO PLACE CABINETS IN CORRECT LOCATIONS. SINK CABINETS ON LEFT SIDE AND DRAWER CABINETS ON RIGHT SIDE. IF YOU HAVE TWO DOOR UNITS, PLACE THEM SO THE HINGES ARE ON THE OUTSIDE OF DESK. PRE-DRILL HOLES INTO MOUNTING CLEATS AND FRAME SUPPORTS TO PREVENT CRACKING .

BACK VIEW OF INSTRUCTORS DESKDOORS, DRAWERS, BACKS, AND HARDWARE REMOVED TO SHOW CLARITY

CABINET COMBINATION FOR INSTRUCTOR'SDESK WITH SINK

NOTE:


B94 CABINET

B33 CABINET

CABINET AND CURVEDPANEL FLUSH

CURVED FRONTMOUNTING CLEAT - TYPICAL

B93 AND B33 CABINETS



ASSEMBLY TEMPLATE

REVISION LEVEL


REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE




APR:DATE





1314K, 1324K, 1334K, & 1344K


REV A6 OF 13NTS

EMK 12/13/17


STEP 3:

PLACE TOEKICK IN BETWEEN THE TWO CABINETS ON BOTTOM. MAKE SURE BOTTOM EDGE OF TOEKICK IS FLUSH WITH BOTTOM

EDGE OF CABINETS. ATTACH REMOVABLE PANEL ABOVE TOEKICK TO THE FRAME

SUPPORTS ON CURVED FRONT WITH SCREWS PROVIDED. PRE-DRILL HOLES IN FRAME SUPPORTS TO PREVENT CRACKING . YOU MAY NEED TO TRIM DOWN TOEKICK AND REMOVABLE

PANEL TO FIT IN BETWEEN CABINETS.

TOEKICK

REMOVABLEPANEL

NOTE:




ASSEMBLY TEMPLATE

REVISION LEVEL


REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE




APR:DATE





1314K, 1324K, 1334K, & 1344K


REV A7 OF 13NTS

EMK 12/13/17


STEP 4:

POSITION APRON IN BETWEEN THE TWO CABINETS. APRON SHOULD BE OFFSET 0.25" FROM THE FRONT EDGE OF THE SIDES. MAKE SURE TOP EDGE IS FLUSH WITH TOP EDGE OF SIDES. WITH HELP FROM ANOTHER PERSON, ATTACH L-BRACKET ONTO APRON AND

INTERNAL SIDES WITH HARDWARE PROVIDED. MAKE SURE BRACKETS ARE ALSO FLUSH WITH TOP EDGE OF CABINETS. YOU MAY NEED TO TRIM DOWN APRON TO FIT IN BETWEEN CABINETS.

CLOSE UP OF APRON AND L-BRACKET ASSEMBLY SHOWN

NOTE:


APRON

APRONL-BRACKET

FLUSH WITH TOP EDGEOF SIDES AND APRON

0.25DISTANCE FROM FRONTEDGE OF SIDE TO FRONT

EDGE OF APRON

INTERNAL SIDE



ASSEMBLY TEMPLATE

REVISION LEVEL


REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE




APR:DATE





1314K, 1324K, 1334K, & 1344K


REV A8 OF 13NTS

EMK 12/13/17


STEP 5:

APPLY SILICONE ADHESIVE TO TOP EDGES OF CABINETS AND APRON. PLACE MAIN TOP OVER CABINETS AND APRON WITH PROPER OVERHANG (CENTERED ON INSTRUCTOR'S DESK). MAKE SURE BACK EDGE OF TOP SITS TIGHT AGAINST CURVED FRONT (FLUSH WITH BACK EDGE OF CABINETS). WIPE OFF ANY EXCESS CAULK. CLAMP TOP ONTO APRON AND TOPS OF CABINETS TO REMOVE ANY WARP USING SHIMS AND C-CLAMPS, IF

NEEDED, WHEN ALIGNING THE TOP (DO THIS BEFORE ADHESIVE SETS UP). LET CURE FOR 6-12 HOURS. DO NOT APPLY SILICONE ADHESIVE TO REMOVABLE PANEL .

TOP VIEW OF INSTRUCTOR'S DESK SHOWN

NOTE:


CURVED FRONT

DO NOT APPLYSILICONE ADHESIVE TO

REMOVABLE PANEL

APPLY SILICONE ADHESIVETO TOP EDGES OF

CABINETS AND APRON



ASSEMBLY TEMPLATE

REVISION LEVEL


REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE




APR:DATE





1314K, 1324K, 1334K, & 1344K


REV A9 OF 13NTS

EMK 12/13/17



STEP 6:

IF YOUR INSTRUCTOR'S DESK HAS A SINK, APPLY SILICONE ADHESIVE TO SINK OPENING ON TOP. LOWER SINK INTO OPENING. APPLY SILICONE ADHESIVE TO CUT EDGE OF BACKSPLASH. POSITION IT ON THE BACK EDGE OF MAIN TOP (WILL SIT TIGHT AGAINST CURVED FRONT). WIPE OFF ANY EXCESS CAULK AND ALLOW TO SET. LET CURE FOR 6-12 HOURS.

NOTE:


MAIN TOP

APPLY SILICONEADHESIVE AROUNDOPENING FOR SINK

PLACE BACKSPLASH HERE



ASSEMBLY TEMPLATE

NOTE:


REVISION LEVEL


REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE




APR:DATE





1314K, 1324K, 1334K, & 1344K


REV A10 OF 13NTS

EMK 12/13/17



STEP 7:

APPLY SILICONE ADHESIVE TO TOP EDGES OF CURVED FRONT. PLACE TOP ON CURVED FRONT WITH PROPER OVERHANG (CENTERED ON INSTRUCTOR'S DESK). WIPE OFF ANY EXCESS CAULK AND ALLOW TO SET. LET CURE FOR 6-12 HOURS.

SINK

BACKSPLASH

MAIN TOP



ASSEMBLY TEMPLATE

NOTE:


REVISION LEVEL


REV.

A -

DWN

TITLE:

BY:

BY:APR

DATEDWN:

APR:DATE




APR:DATE





1314K, 1324K, 1334K, & 1344K


REV A11 OF 13NTS

EMK 12/13/17


COMPLETE UNIT SHOWN

STEP 8:

ATTACH RUBBER MOLDING TO BASE OF CABINETS USINGCONTACT CEMENT.

SCREW STAINLESS STEEL CORNERS BRACKETS ON EACHCORNER OVER BASE MOLDING WITH HARDWARE PROVIDED.

IF YOUR INSTRUCTOR'S DESK HAS SINK, INSTALL MULTI-SERVICEFIXTURES IN THE HOLES PROVIDED ON TOP.

ATTACH RUBBERMOLDING TO BASE

CURVED TOP

MULTI-SERVICE FIXTURE



Dup“Loaprotcircthe

lex Read” sitects tuit. In“Line”

eceptde of the Dncomi” side

tacle the Guplexing poe of th

is preGFCI Rx Receower mhe GFC

e-wireRecepeptacmust CI Rec

ed to tptaclele on be wicepta

the e. This

the ired toacle.

s

o

TROUBLESHOOTING YOUR GFCI ELECTRICAL RECEPTACLE:

PLEASE NOTE: THROUGHOUT ANY OF THE FOLLOWING STEPS (PROCEDURES); IF YOU ARE NOT SURE YOU CAN DO THIS JOB SAFELY, AND COMPETENTLY, REFER THIS WORK TO QUALIFIED PROFESSIONAL! If your unit comes equipped with a GFCI (Ground Fault Circuit Interrupter) electrical

receptacle, and there is no power in the receptacle please consider/check the following:

• The extension cord (if being used) is working properly. • The breaker hasn’t been tripped, or turned off.

This type of GFCI has two testing-related buttons on it. One button is appropriately labeled “TEST”,

and the other button is labeled “RESET”. To test the GFCI receptacle follow these steps:

• Plug in an appliance (lamp or night light) into the outlet. The light should now be on. Then press the “TEST” button on the GFCI. The GFCI “RESET” button should pop out, and the light should go out.

• If the “RESET” button pops out, but the light doesn’t go out, the GFCI has been improperly wired. In this case please contact a certified professional. There may also be a problem with other wiring in the same circuit.

• If the “RESET” button doesn’t pop out, the GFCI is defective, or malfunctioned, and should be replaced.

• If the GFCI is functioning properly, and the lamp goes out, press the “RESET” button to restore power to the outlet.

Conversely, if you have a GFI that has tripped (which is common) and it will not reset, you may

have a wiring short in the circuit, a defective appliance on the circuit, or the GFI itself has become

defective. To test a tripping GFCI follow these steps:

• Remove every appliance connected to the GFCI's circuit and reset it. If it doesn't reset there may either be a wiring fault behind a socket outlet, or your GFCI itself has become faulty.

• Make sure whatever you are plugging into to the GFCI is dry and not damaged. • Only plug in one item at a time. If you are plugging in a defective item it will cause the GFCI

to trip, and that item therefore should be replaced.

If you are still having difficulty the easiest way to troubleshoot a GFI is to obtain a GFI tester, which

is available at most hardware stores. It plugs into the GFI outlet, and will supply you with a

"snapshot" of your connections, indicating wiring problems and/or the condition of the GFI. Another

way to troubleshoot is to simply purchase a new GFI and install it.

VERSA CURVE INSTRUCTOR DESK - Amazon S3...versa curve instructor desk assembly instructions nts4 of...

Documents

Transcript of VERSA CURVE INSTRUCTOR DESK - Amazon S3...versa curve instructor desk assembly instructions nts4 of...