Versa 3501

www.versa-valves.com

Series V-316STAINLESS STEEL VALVES

AND ACCESSORIES

BULLETIN V316-2007

67439_COVS No Varn.indd 167439_COVS No Varn.indd 1 2/23/07 8:59:37 AM2/23/07 8:59:37 AM

2.1

MODULAR CONCEPT Versa exercises diligence to assure that in formation contained in this catalog is correct, but does not accept responsibility for any errors or omissions. Versa also reserves the right to change or delete data or products at any time without prior notifi cation. To be sure the data you require is correct, consult factory.

The V-316 Valve Series provides a full range of control valves suited to the most demanding of applications. Ruggedly constructed, both internally and externally, of stainless steel, these valves are able to withstand the physical abuse of corrosive environments and controlled media.

A modular design concept utilizing three basic sub-assemblies: a BodyAssembly and two Actuator Assemblies (active or passive), simplifi es circuit planning while affording almost unlimited combination possibilities.

Port sizes are 1/4 NPT, 3/8 NPT and 1/2 NPT in three-way (3/2, 3/3), and four-way (5/2 and 5/3) styles.

Actuation types include manual (hand lever, palm button, latching detent & manual reset), pilot (pressure pilot, diaphragm pilot, “air-latch” pilot), and solenoid-pilot (including several approved hazardous service types).

VAG-4522-316-181DE-XX-(specify voltage)

‘A’-181DESub-Assembly Nr.: CA-4302-65-316-181DE

‘S’ Sub-Assembly Nr.: SA-4302-65-316

‘P’Sub-Assembly Nr.: SA-4302-64-316

‘4522’Sub-Assembly Nr.: SA-4522-71-316

‘G’-XXSub-Assembly Nr.:SA-4322-84-316-XX (specify voltage)

Manual Actuator

Solenoid-Pilot Actuator

Body Assembly

Spring Return ActuatorPilot Actuator

Other functions can be easilyaccomplished as shown with these Pilot and Spring Return actuators.

This Bulletin only gives the Actuator Sub-Assemblies and Body Sub-Assemblies. This gives the design engineer maximum versatility as these modules can be combined to complete valves with functions as needed.

67439_COVS No Varn.indd 267439_COVS No Varn.indd 2 2/23/07 9:00:36 AM2/23/07 9:00:36 AM

3.1

TECHNICAL DATA

MATERIALS: Metal Parts: 316 stainless steel (except solenoid parts, ask factory)conforms to NACE standard MR-01-75.

Hand Knob: plastic Seals: FKM (Fluorocarbon) is standard. Exceptions: diaphragm-pilot seal is NBR (Buna N) or with suffi x -31

Tefl on coated Buna N; other seal materials are available. See ‘TEMPERATURES/SEALS’ below.PRESSURES:

Valve type Pneumatic*

psibar

(Mpa = bar ) 10

VALVE BODY (inlet/system)Manual or Pilot — Standard SealsSingle Solenoid EXPilot (2-position) — Standard SealsDouble Solenoid EXPilot (2-position) — Standard SealsDouble Solenoid EXPilot (3-position) — Standard Seals

Vacuum to 200 Vacuum to 14

Single Solenoid INPilot (2-position) — Standard SealsDouble Solenoid INPilot (2-position) — Standard SealsDouble Solenoid INPilot (3-position) — Standard Seals

40 to 17520 to 17540 to 175

2.8 to 121.4 to 122.8 to 12

PILOT (signal)Some restrictions concerning maximum pressures may apply.See specifi c actuator.Pilot (2-position “VSP” or 3-position “VJJ”)Pilot (2-position “VPP”)Diaphragm (2-position “VSW” or 3-position “VYY”)Diaphragm (2-position “VSW” or 3-position “VYY”) w/Suffi x -31Diaphragm (2-position VWW”)Diaphragm (2-position “VWW”) w/Suffi x -31Solenoid EXPilot (2-position “VSG” or 3-position “VXX”)Solenoid EXPilot (2 position (VGG”)

40 to 20020 to 20010 to 5010 to 200 5 to 50 5 to 20040 to 17520 to 175

2.8 to 141.4 to 140.7 to 3.40.7 to 140.34 to 3.40.34 to 142.8 to 121.4 to 12

Notes: — When application involves temperatures below freezing or when shifting intervals are relatively long, it is recommended that suffi x -S be specifi ed for valves with spring actuation. Minimum pilot pressure must be increased by 40%.

Notes: — The following suffi xes include the use of suffi x -S in all cases: -181AAE, -181CE, -181DE, -3358AE, -3358E.*Consult factory for hydraulic service.

TEMPERATURES/SEALS: The table below lists suggested suffi x options for various temperature ranges and/or types of service. For temperatures or conditions not listed, consult factory.

Type of Service

Temperature Range(Medium/AmbientTemperature)

Intermittent Duty Service Continuous Duty Service

AC or DC AC DC

Coil Solenoid Plunger Coil Solenoid Plunger Coil Solenoid Plunger

150ºF to 200ºF(65ºC) (95ºC)

Suffi x-HT

Suffi x -3 (may be inclusive in other suffi x options as it is in -HT)

Suffi x-HT


Suffi x-HT


120ºF to 150ºF(50ºC) (65ºC)

Standard Suffi x -3 (may be inclusive in other suffi x options)


Suffi x-HT


-10ºF to 120ºF(-23ºC) (50ºC)

Standard Standard Standard Suffi x -3 (may be inclusive in other suffi x options)


FLOW CALCULATION:Air Flow = f ��(p1-p2)(p2)

(T)(SG)

English Metric

Air fl ow SCFM Nm3/h

f = Conversion factor 22.5 × Cv 30.8 × Kv

p1 = Upstream pressurep2 = Downstream pressure

p1 - p2 < 0.5 × p2

psi absolute bar absolute

T = Temperature upstream absolute 460º + Fº 273º + Cº

SG = Specifi c gravity 1.0 1.0

Note: 0.59 SCFM = 1 Nm3/h14.5 psi = 1 bar

FLOW:Port Size of Valve BodyFor details see page 8.1 through 8.6

Flow Diameterinch mm

Flow FactorCv Kv

1/4 NPT3/8 NPT1/2 NPT

3/8 9.53/8 9.55/8 16.0

1.8 262.0 295.5 80

67439.indd 3.167439.indd 3.1 1/18/07 8:52:39 AM1/18/07 8:52:39 AM

3.2

ELECTRICAL:Solenoid-Pilot actuated V316 valves are available with a variety of different solenoids for both nonhazardousand hazardous locations. Basic details of these actuators are listed below. Dimensions, product numbers, andother details may be found on pages 5.1 through 5.6. For additional data consult factory.

NON HAZARDOUS LOCATION SOLENOIDS

Suffi xIdentifi cation

ProtectionClassifi cation

Area Classifi cationand (Gas Grouping)

Certifi cation-(Conformance)

IngressProtection

-U General Purpose Indoor & Outdoor CSA NEMA 1, 2, 3

-HC -U General Purpose Indoor & Outdoor CSA NEMA 4;IP65 per IEC 529

HAZARDOUS LOCATION SOLENOIDS

Suffi xIdentifi cation

ProtectionClassifi cation

Area Classifi cationand (Gas Grouping)

Certifi cation-(Conformance)

IngressProtection

-XX

Page 5.3

Hazardous Locations Class I, Division 2 (A & B)Class I, Division 1 (C & D)Class II, Division 1 (E, F, & G)

ULCSA

NEMA 7 & 9

-LB-XX

Page 5.4

Hazardous Locations Class I, Division 2 (A & B)Class I, Division 1 (C & D)Class II, Division 1 (E, F, & G)

ULCSA

NEMA 7 & 9

-XN

Page 5.3

(d) Flameproof Zones 1 and 2(IIB+H2) Category 2GT4

ATEX IP66

-LB-XN

Page 5.4

(d) Flameproof Zones 1 and 2(IIB+H2) Category 2GT6

ATEX IP66

-XDASor-XDATPage 5.3

(d) Flameproof Zones 1 and 2 (IIC) Category 2G

ATEX IP66 and IP67

-XMAAor-XMAEor-XMAFor-XMAGPage 5.5

(m) Encapsulation(e) Increased Safety

Zones 1 and 2 (II) Category 2G

ATEX IP66 and IP67

-XMFAor-XMFEor-XMFFor-XMFGPage 5.5

(m) Encapsulation(e) Increased Safety

Zones 1 and 2 (II) Category 2G

ATEX IP66 and IP67

-HC-XISC-HCC-XISC

Page 5.6

Hazardous Locations Class I,Groups (A, B, C & D)Class II, Groups (E, F & G)Class III, Division 1

Factory MutualCSA

NEMA 4

-HC-XISX6-HCC-XISX6

Page 5.6

(ia) Intrinsic Safe Zones 0, 1 and 2(IIC) Category 1G

T6

ATEX IP65

-XIFAor-XIFEor-XIFF

Page 5.6

(ib) Intrinsic Safe Zones 1 and 2(IIB) Category 1G

ATEX IP66 and IP67

TECHNICAL DATA

67439.indd 3.267439.indd 3.2 1/18/07 8:52:40 AM1/18/07 8:52:40 AM

3.3

PRODUCT NUMBER COIL CODES: Complete product numbers require, when applicable, a coil code that represents the desired coil current type, frequency and voltage. The coil code takes the form shown below, with ratings and voltage substituted as required.

Rating Code

A = 60Hz frequencyD = Direct Current (DC)E = 50Hz frequency

Voltage(Indicated by three digits:

as example,24 volts = 024120 volts = 120.)

onVoltage(Power)

ElectricalCharacteristics Miscellaneous

All usual 50 Hz & 60 Hz AC (6W)All usual DC (7W)

Class F epoxy molded coil (155ºC). Continuous duty2 leads 24” (60 cm).

Steel cover with 1/2 NPT conduit entry..1

24V60, 120V60, 240V60 (8.5W)24V50, 110V50, 220V50 (8.5W)12VDC, 24VDC, 48VDC (10.5W)

Class F epoxy molded coil (155ºC), with 3 spadeterminals and mini DIN socket with PG9 cable gland.Continuous duty.

Page 5.1

Voltage(Power)

ElectricalCharacteristics Miscellaneous

All usual 50 Hz & 60 Hz AC (5.6W)All usual DC (7.2W)

Class F epoxy molded coil (155ºC).Continuous duty.3 leads 24” (60 cm).

Steel chromate coated coil housing with 1/2 NPT conduit entry.For stainless steel (182FM) coil housing add: (-ST)

12V60, 24V60, 48V60, 120V60, 240V60 (1.8W)6VDC, 12VDC, 24VDC, 48VDC (1.8W)


Steel chromate coated coil housingwith 1/2 NPT conduit entry.For stainless steel (182FM ) coil housing add: (-ST)Maximum pilot pressure 120 psi (8 bar).1.8W nominal power.

All usual 50 Hz & 60 Hz AC (5.6W)All usual DC (7.2W)


Steel chromate coated coil housingwith M20 x 1.5 conduit entry.Ground terminal on cover.For stainless steel (182FM) coil housing add: (-ST)

12V60, 24V60, 48V60, 120V60, 240V60 (1.8W)6VDC, 12VDC, 24VDC, 48VDC (1.8W)


Steel chromate coated coil housingwith M20 x 1.5 conduit entry.Ground terminal on cover.For stainless steel (182FM) coil housing add: (-ST)Maximum pilot pressure 120 psi (8 bar)1.8W nominal power.

24V50, 230V50 (6W); 127V50 (10W)24V60, 120V60, 240V60 (10W)12VDC, 24VDC, 28VDC, 48VDC,110VDC, 125VDC (10W)

Class F epoxy molded coil (155ºC).Continuous duty.

Stainless steel coil housing with internal Junction Box. Internal and external ground screw.M20 x 1.5 conduit entry: (-XDAS)1/2 NPT conduit entry: (-XDAT)

24VDC (4W)(Consult factory for other voltage options)

Continuous duty. Coil & Rectifi er,including surge suppression,potted within housing.

Thick wall epoxy coil housing with integraljunction box. Internal ground terminal.M20 x 1.5 conduit entry: (-XMAA)Cable gland for 6-12 mm ø cable: (-XMAE)1/2 NPT conduit entry with adapter: (-XMAF)Cable gland for 9-16 mm ø cable: (-XMAG)

24VDC(10W inrush, 2.6W holding)(Consult factory for other voltages)

Continuous duty. Coil & Power Controller potted withinhousing.

Thick wall epoxy coil housing with integral junction box. Internal ground terminal.M20 x 1.5 conduit entry: (-XMFA)Cable gland for 6-12 mm ø cable: (-XMFE)1/2 NPT conduit entry with adapter: (-XMFF)Cable gland for 9-16 mm ø cable: (-XMFG)

24VDCsystem voltage prior to barrier(1.6 watt max.)


Requires the use of an approved barrier or isolator.Maximum operating system voltage before barrier 28VDC. Maximum pilot pressure 115 psi (8 bar).3 spade terminals & DIN connector with PG9cable gland: (-HC)1/2 NPT conduit entry: (-HCC)

24VDCsystem voltage prior to barrier(1.6 watt max.)


Requires the use of an approved barrier or isolator.Maximum operating system voltage before barrier 28VDC. Maximum pilot pressure 115 psi (8 bar).3 spade terminals & DIN connector with PG9cable gland: (-HC)1/2 NPT conduit entry: (-HCC)

24VDC (0.8W)(Consult factory for other voltages)

Continuous duty. Coil and power controller potted within housing.

Requires the use of an approved safety barrier or isolator.Thick wall epoxy coil housing and integraljunction box. Internal ground terminal.M20 x 1.5 conduit entry: (-XIFA)Cable gland for 6-12 mm ø cable: (-XIFE)1/2 NPT conduit entry with adapter: (-XIFF)

67439.indd 3.367439.indd 3.3 1/18/07 8:52:40 AM1/18/07 8:52:40 AM

3.4

SELECTOR CHART & PRODUCT NUMBERINGE

ach

lette

r an

d di

git i

n th

e pr

oduc

t num

ber

of a

Ver

sa V

alve

has

a s

igni

fi can

t mea

ning

, as

expl

aine

d be

low

.Le

tters

or

num

bers

sho

wn

in b

lack

in th

e ex

ampl

e be

low

do

not c

hang

e.

VS

P3

30

131

6S

uffi x

Valv

eS

erie

s

BO

DY

DE

TAIL

S

AC

TUAT

ING

DE

VIC

ES

Func

tion

(als

o se

e S

poo

lD

etai

ls)

Por

t S

ize

Typ

eof

Bod

y

Sp

ool

Det

ails

(fl ow

pat

tern

*)A

t le

ft e

nd o

f va

lve

At

right

end

of

valv

ew

hen

look

ing

at in

let

por

t of

bod

y*

Ser

ies

V-31

6 Va

lves

P

neum

atic

S

ervi

ce

(Nom

inal

P

ress

ure

Ran

ge

Vacu

um t

o 20

0 p

si (1

4 b

ar).

Som

e re

stric

tions

ap

ply

.S

ee s

pec

ifi c

actu

ator

s.)

AC

omb

inat

ion

- or

Sp

ecia

l A

ctua

tor

3*Th

ree-

Way

3/2

or 3

/3

4Fo

ur-W

ay5/

2 or

5/3

7Tw

o O

utle

t(D

iver

ter)

3/2

or 3

/3

8Tw

o In

let

(Sel

ecto

r)3/

2 or

3/3

* Two-

Way

may

b

e ac

com

plis

hed

by

plu

ggin

g th

e ex

haus

t p

ort

of

thre

e-w

ay v

alve

b

odie

s

31/

4 N

PT

43/

8 N

PT

51/

2 N

PT

Sid

epor

ted

E

XP

ilot

0B

ody

with

th

read

ed

sid

e-p

orts

(fo

r M

anua

l, P

ilot

and

EX

-P

ilot

sole

noid

ac

tuat

ed

valv

es)

Sid

epor

ted

INP

ilot

2B

ody

with

th

read

ed

sid

e-p

orts

an

d in

tern

al

dril

ling

to

sup

ply

inle

t p

ress

ure

to

INP

ilot

act.

of

Sol

enoi

d-p

ilot

Thre

e-W

ay3/

2 Va

lves

1N

orm

. Clo

sed

2N

orm

. Op

en

2Tw

o O

utle

t(S

ee F

unct

ion

colu

mn

for

fl ow

)

2Tw

o In

let

(See

Fun

ctio

n co

lum

n fo

r fl o

w)

Thre

e-W

ay3/

3 Va

lves

3 4

For

3/3

Two-

inle

t or

Two-

outle

tse

e p

g. 8

.3

Four

-Way

5/2

Valv

es

2 Four

-Way

5/3

Valv

es

3 4 *Lef

t an

d R

ight

Flo

w

Dia

gram

s in

dic

ate

2-p

ositi

on v

alve

. C

ente

r Fl

ow D

iagr

am

show

s 3-

pos

ition

. For

ot

her

Cen

ter

Flow

p

atte

rns,

see

pag

es

8.1

thru

8.6

‘316

’ ind

icat

es

that

the

bas

ic

cons

truc

tion

mat

eria

l for

val

ve

par

ts is

AIS

I 316

S

tain

less

Ste

el(C

onfo

rms

to

NA

CE

Sta

ndar

d

MR

-01-

75)

Suf

fi x D

etai

l nu

mb

ers

ind

icat

e m

odifi

catio

ns o

r va

riatio

ns o

f the

b

asic

Val

ve. W

hen

spec

ifyin

g, s

imp

ly

add

the

Suf

fi x

Det

ails

req

uire

d

in a

lpha

bet

ical

an

d n

umer

ical

fo

llow

ing

ord

er.

In t

his

bul

letin

m

any

Suf

fi x

Det

ails

are

d

escr

ibed

. For

m

ore:

see

Suf

fi x

Det

ail P

rod

uct

Bul

letin

, or

cons

ult

fact

ory.

Coi

l vol

tage

s ar

e in

dic

ated

he

re. F

or s

pec

ifi c

volta

ge, u

se c

oil

cod

e nu

mb

er

liste

d o

n p

age

3.3.

B

Sp

ring

cent

erin

g(fo

r 3

pos

ition

man

ually

op

erat

ed v

alve

s)

GS

olen

oid

-pilo

t

IH

and

But

ton

(for

pan

el m

ount

ing)

JP

ilot-

Sp

ring

Cen

terin

g

LH

and

-Lev

er

NN

on-r

etur

n en

d-c

ap

PP

ress

ure-

Pilo

t

RR

ever

se S

prin

g R

etur

n(s

prin

g p

ulls

val

ve s

poo

l)

SS

prin

g R

etur

n(s

prin

g p

ushe

s va

lve

spoo

l)

U3-

Pos

ition

Det

ent

(For

3 p

ositi

on m

anua

lly

oper

ated

val

ves)

WD

iap

hrag

m-P

ilot

(low

pre

ssur

e-p

ilot)

XS

olen

oid

-Pilo

tS

prin

g C

ente

ring

(for

3 p

ositi

on s

olen

oid

p

ilot

valv

es)

YD

iap

hrag

m-P

ilot

Sp

ring

Cen

terin

g(fo

r 3

pos

ition

D

iap

hrag

m-P

ilot

valv

es)

Z2-

Pos

ition

Det

ent

(for

2-p

ositi

on m

anua

lly

oper

ated

val

ves)

*3-w

ay N

C fu

nctio

n re

qui

res

actu

ator

dev

ice

on r

ight

. 3-w

ay N

O fu

nctio

n re

qui

res

actu

ator

d

evic

e on

left

.

VE

RS

A S

erie

s V-

316

Valv

es c

onsi

st o

f thr

ee S

ub-A

ssem

blie

s: o

ne B

ody-

Ass

emb

ly a

nd t

wo

Act

uato

r-A

ssem

blie

s, m

ount

ed a

t th

e LH

sid

e an

d t

he R

H s

ide

of t

he B

ody.

All

the

Act

uato

rs

can

be

mou

nted

at

eith

er s

ide,

are

fully

inte

rcha

ngea

ble

and

can

be

com

bin

ed t

o su

it th

e fu

nctio

n d

esire

d. S

ee P

ages

4.1

thr

ough

8.6

for

thos

e S

ub-A

ssem

blie

s.

67439.indd 3.467439.indd 3.4 1/18/07 8:52:40 AM1/18/07 8:52:40 AM

4.1

PILOT ACTUATORS*

Symbol DesignationIn Product Number

Title andSub-assembly Number

Prefi x Suffi x

(PRESSURE) PILOTP SA-4302-64-316

PULL TYPE (PRESSURE) PILOTA and -PTP CA-4302-64-316-PTP

(PRESSURE) PILOT with ThreadedVent port

P and -107E SA-4302-64-316-107E

PUSH-PULL (PRESSURE) PILOTA and -PPP CA-4302-64-316-PPP

(PRESSURE) PILOT-SPRINGCENTERED(for 3 position pilot operated valves)

J SA-4302-83-316

“AIR LATCH” (PRESSURE) PILOT‘hold function’ only

A and -301E CA-4302-64-316-301E

“AIR LATCH” (PRESSURE) PILOT-PULL TYPE‘hold function’ only

A and -301RE CA-4302-64-316-301RE

*For Pilot Pressure ranges see page 3.1

DIMENSIONS SHOWN IN INCH MM

67439.indd 4.167439.indd 4.1 1/18/07 8:52:42 AM1/18/07 8:52:42 AM

4.2

PILOT ACTUATORS*



Prefi x Suffi x

DIAPHRAGM PILOT(for 2 position diaphragm pilot operated valves)

W SA-4302-87-316For low pressure pilot signals

DIAPHRAGM PILOT-SPRING CENTERED(for 3 position diaphragm pilot operated valves)

Y For low pressure pilot signalsSA-4302-88-316

NOTE: Diaphragm piston can be equipped with Tefl on coated Buna N “U” cup. Add suffi x “-31” to complete valve number or sub-assembly number.

(PRESSURE) PILOT-TWO DETENTA and -150E CA-4302-64-316-150E

(PRESSURE) PILOT-REVERSESPRING RETURN

A and -159E CA-4302-64-316-159E

*For Pilot Pressure ranges see page 3.1


PILOT-COMBINATION ACTUATORS*DIMENSIONS SHOWN IN INCH

MM

67439.indd 4.267439.indd 4.2 1/18/07 8:52:45 AM1/18/07 8:52:45 AM

5.1

SOLENOID-PILOT ACTUATORS — 2 PositionGENERAL SERVICE(NONHAZARDOUS SERVICE)




Prefi x Suffi x

SOLENOID PILOT(with threads for conduit connection)

G and -U SA-4302-84-316-U-.+.-(**)(EXPilot type)

G and -U SA-4322-84-316-U-.+.-(**)(INPilot type)

3 Position— GENERAL SERVICE (NONHAZARDOUS SERVICE) 3 Position— HAZARDOUS SERVICE Any of the solenoids shown on pages 5.3, 5.4, 5.5,

and 5.6 can be used on this actuator. SOLENOID-PILOTSPRING CENTERING(for 3 posiition solenoid operated valves)

Available for any of the solenoids and re-spective options shown on pages 5.1, 5.3, 5.4, 5.5 and 5.6.

X and -.U. SA-4302-85-316-.U.-.+.-(**)(EXPilot type)

X and -.U. SA-4322-85-316-.U.-.+.-(**)(INPilot type)

(**) Specify coil code on page 3.3, to complete number

2 Position— GENERAL SERVICE (NONHAZARDOUS SERVICE)

SOLENOID-PILOT(with DIN type connector-spade terminal coil)

G and -HC-U SA-4302-84-316-HC-U-.+.-(**)(EXPilot type)

G and -HC-U SA-4322-84-316-HC-U-.+.-(**)(INPilot type)

3 Position(For 3 Position also refer to drawing at top of page)

— GENERAL SERVICE (NONHAZARDOUS SERVICE)SOLENOID-PILOTSPRING CENTERING(with DIN type connector-spade terminal coil)

X and -HC-U SA-4302-85-316-HC-U-.+.-(**)(EXPilot type)

X and -HC-U SA-4322-85-316-HC-U-.+.-(**)(INPilot type)


� Height dimensions shown are for Nonhazardous solenoids.Dimension for Hazardous solenoids depend upon type ofsolenoid selected.

Suffi x

+options: -HT High Temperature Class H coil-H2 adapter with 1/8 NPT thread-L14 Dust Excluder Solenoid Nut-ME manual override-PC potted coil; NEMA 4/4X, IP65-243 wire leads with grommet type

housing

Suffi x

+options: -HT adapter with 1/8 NPT thread-L14 Dust Excluder Solenoid Nut-ME manual override

1.6241.3

2.5464.6

VERSA

Manual Override(Suffix - ME)

1/2 - 14 NPTConduit Conn

24” LeadsThird Wire GroundSupplied WhenRequested

12531.7

10-32 UNFAdapter Option1/8 NPT (Suffix - H2)

2.1153.5

.9423.9

.6917.5

2 Position

3 Position

1.3835.1

1/8 NPT Pilot Inlet Port(on EXPilot Valves only)

3.0076.2

1.6241.3

Mini DINConnector

PG-9Cable Entry

1.4837.7

10-32 UNFAdapter Option1/8 NPT (Suffix - H2)

.9423.9

.6917.5

1.3835.1

1/8 NPT Pilot Inlet Port(on EXPilot Valves only)

3.0076.2

Manual Override(Suffix - ME)

2 Position (For 3 Position refer

also to drawing at top of page)

3.6292.0

.5714.5

.5714.5

67439.indd 5.167439.indd 5.1 1/18/07 8:52:47 AM1/18/07 8:52:47 AM

5.2

SOLENOID-PILOT COMBINATION ACTUATORS — 2 PositionGENERAL (NONHAZARDOUS) OR HAZARDOUSSERVICE


DesignationIn Product Number


Prefi x Suffi x

SOLENOID-PILOT andREDUNDANT SOLENOID-PILOT

A and -RS-.?.- CA-4302-84-316-RS-.?.-.+.-(**)(EXPilot type)

A and -RS-.?.- CA-4322-84-316-RS-.?.-.+.-(**)(INPilot type)

? Specify suffi x on page 3.2, which solenoid operator is required.

+ Specify Options

(**) Specify coil code to complete number.



Prefi x Suffi x

SOLENOID-PILOT and‘REVERSE’ SPRING RETURN

A and -138E-.?.- CA-4302-84-316-138E-.?.-.+.-(**)(EXPilot type)

A and -138E-.?.- CA-4322-84-316-138E-.?.-.+.-(**)(INPilot type)

SOLENOID-PILOTTWO DETENT

A and -173E-.?.- CA-4302-84-316-173E-.?.-.+.-(**)(EXPilot type)

A and -173E-.?.- CA-4322-84-316-173E-.?.-.+.-(**)(INPilot type)

SOLENOID ‘AIR-LATCH’ PILOT‘hold function only’

A and -301GE-.?.- CA-4302-84-316-301GE-.?.-.+.-(**)(EXPilot type)

A and -301GE-.?.- CA-4322-84-316-301GE-.?.-.+.-(**)(INPilot type)

? Specify suffi x on page 3.2, which solenoid operator is required.

+ Specify Options

(**) Specify coil code to complete number.

REDUNDANT SOLENOID ACTUATOR — 2 PositionGENERAL SERVICE (NONHAZARDOUS)OR HAZARDOUS SERVICE


Any of the solenoids shown on pages 5.1, 5.3, 5.4, 5.5, and 5.6 can be used on this actuator

67439.indd 5.267439.indd 5.2 1/18/07 8:52:51 AM1/18/07 8:52:51 AM

5.3

SOLENOID-PILOT ACTUATORS — 2 Position (for 3 Position also refer to Drawing at top of page 5.1)HAZARDOUS SERVICEDIMENSIONS SHOWN IN INCH

MMSymbol Designation

In Product NumberTitle andSub-assembly Number

Prefi x Suffi x

SOLENOID-PILOTHazardous Locations{-XX: UL listed & CSA approved for Hazardous Locations; Class I, Div 2 (A & B); Class I, Div 1 (C & D); Class II, Div 1 (E, F & G).}(d) Flameproof{-XN: ATEX approved; Zones 1 and 2, (IIB + H2) Category 2G.}

G and -XX SA-4302-84-316-XX-.+.-(**)G and -XN SA-4302-84-316-XN-.+.-(**)

(EXPilot type)

G and -XX SA-4322-84-316-XX-.+.-(**)G and -XN SA-4322-84-316-XN-.+.-(**)

(INPilot type)

Suffi x

+options: -HT High Temperature Class H coil (For UL or CSA approved, consult factory)

-H2 adapter with 1/8 NPT thread -L14 Dust Excluder Solenoid Nut-ME manual override-ST #182FM stainless steel coil housing-PC potted coil; NEMA 4/4X, IP65


SOLENOID-PILOT(d) Flameproof{-XDAS or –XDAT; ATEX approved; Zones 1 and 2, (IIC) Category 2G.}

G and -XDA* SA-4302-84-316-XDA..*.-.+.-(**)(EXPilot type)

G and -XDA* SA-4322-84-316-XDA..*.-.+.-(**)(INPilot type)

*Specify identifi cation detail. DetailS: M20 x 1.5 conduit entryT: 1/2 NPT conduit entry

Suffi x

+options: -HT High Temperature Class H coil-H2 adapter with 1/8 NPT thread-H2 adapter with 1/4 NPT thread-303 Varistor for suppression purposes

included


1/8 NPT Pilot Inlet Port ( on EXPilot Valves only )

3.0878.3

1.52 38.5

1.44 36.5

.5714.5

10-32 UNF

Adapter Option 1/8 NPT ( Suffix -- H2 )

24” Leads 2 Wire w/Ground

1/2 - 14 NPT (-XX)M20 x 1.5 (-XN)Elect Conn

Manual Override (Suffix - ME )

1.6241.3

.6917.5

.94 23.9

2.2657.4

1.38 35.1

Earthen Ground for -XN

1/2 - 14 NPT (XDAT)M20 x 1.5 (XDAS)

1/8 NPT (Suffix - H2)1/4 NPT (Suffix - H) 2.2

56.0

3.3585.0

1.37 34.8

.59 15.0

.69 17.5

.61 15.5

1.38 35.0

1/8 NPT Pilot Inlet Port (on EX Pilot Valves only)

VERSAPARAMUS NJ - SA

APELDOORNTHE NETHERLANDS

Ø

Ø

67439.indd 5.367439.indd 5.3 1/18/07 8:52:56 AM1/18/07 8:52:56 AM

5.4


MM

SOLENOID-PILOTLOW-WATT TYPE-Nominal Power 1.8W

Hazardous Locations{-LB-XX: UL listed & CSA approved for Hazardous Locations; Class I, Division 2 (A & B); Class I, Division 1 (C & D); Class II, Division 1 (E, F & G).}

(d) Flameproof{-LB-XN: ATEX approved; Zones 1 and 2, (IIB + H2) Category 2G.}

Max pilot pressure 120 psi (8 bar); air only.

G and -LB-XX SA-4302-84-316-LB-XX-.+.-(**)G and -LB-XN SA-4302-84-316-LB-XN-.+.-(**)

(EXPilot type)

G and -LB-XX SA-4322-84-316-LB-XX-.+.-(**)G and -LB-XN SA-4322-84-316-LB-XN-.+.-(**)

(INPilot type)

X and -LB-XX SA-4302-85-316-LB-XX-.+.-(**)X and -LB-XN SA-4302-85-316-LB-XN-.+.-(**)

(EXPilot type)

X and -LB-XX SA-4322-85-316-LB-XX-.+.-(**)X and -LB-XN SA-4322-85-316-LB-XN-.+.-(**)

(INPilot type)

Suffi x

+options: -H2 Adapter with 1/8 NPT thread -L14 Dust Excluder Solenoid Nut-ME Manual Override-ST #182 FM stainless steel coil housing




Prefi x Suffi xSymbol

NOTE: 2 position shown. Refer to Drawing page 5.1 for 3 position.

67439.indd 5.467439.indd 5.4 1/18/07 8:52:57 AM1/18/07 8:52:57 AM

5.5


MM



Prefi x Suffi x

SOLENOID-PILOT(m) Encapsulation, (e) Increased Safety {-XMA*: ATEX approved; Zones 1 and 2, (II) Category 2G.}Max. pilot pressure 175 psi [12 bar]

G and -XMA* SA-4302-84-316-XMA*-.+.-(**)(EXPilot type)

G and -XMA* SA-4322-84-316-XMA*-.+.-(**)(INPilot type)

*Specify identifi cation detail.

DetailA: M20 x 1.5 conduit entry.E: Cable gland for 6-12mm ø cableF: 1/2 NPT conduit entry with adapter.G: Cable gland for 9-16 mm ø cable

Suffi x

+options: -H Adapter with 1/4 NPT thread -H2 Adapter with 1/8 NPT thread -L14 Dust Excluder Solenoid Nut

(**) Specify coil code on page 3.3, to complete number.

SOLENOID-PILOT(m) Encapsulation, (e) Increased Safety {-XMF*: ATEX approved; Zones 1 and 2, (II) Category 2G.}Max. pilot pressure 175 psi [12 bar ]

G and -XMF* SA-4302-84-316-XMF*-.+.-D024(EXPilot type)

G and -XMF* SA-4322-84-316-XMF*-.+.-D024(INPilot type)


DetailA: M20 x 1.5 conduit entry.E: Cable gland for 6-12mm ø cable.F: 1/2 NPT conduit entry with adapter.G: Cable gland for 9-16mm ø cable.

Suffi x


1/8 NPT (Suffix - H2)1/4 NPT (Suffix - H)

.7519.1

.6917.5

ADAPTER: 1/2 NPT (-XMAF) CABLE GLAND (-XMAE & -XMAG) 1.38

35.1

.94 23.9

1.6241.3

1/8 NPT Pilot Inlet Port (on EXPilot Valves only)

Manual Override (Suffix -ME)


.7519.1

.6917.5

ADAPTER: 1/2 NPT (-XMFF) CABLE GLAND (-XMFE & XMFG) 1.38

35.1

.94 23.9

1.6241.3

(M20 X 1.5)(-XMFA)



•

(M20 X 1.5)(-XMAA)

RSARSA USA

RN NL

RSARSA USA

RN NL

•

67439.indd 5.567439.indd 5.5 1/18/07 8:53:02 AM1/18/07 8:53:02 AM

5.6



Prefi x Suffi x

SOLENOID-PILOTHazardous Locations{-HC-XISC or –HCC-XISC: Factory Mutual & CSA approved; Class I, Groups (A, B, C, & D); Class II, Groups (E, F, & G); Class III, Div. 1)}

(ia) Intrinsic Safe{-HC-XISX6 or –HCC-XISX6: ATEX approved; Zones 0, 1 & 2; (IIC) Category 1G}Approved Safety Barrier or isolator required. Max. pilot pressure 115 psi [8 bar].

G and -*-XISC SA-4302-84-316-*-XISC-.+.-D024G and -*-XISX6 SA-4302-84-316-*-XISX6-.+.-D024

(EXPilot type)

G and -*-XISC SA-4322-84-316-*-XISC-.+.-D024G and -*-XISX6 SA-4322-84-316-*-XISX6-.+.-D024

(INPilot type)

*Specify identifi cation detail. Detail-HC: 3 spade terminals and mini DIN

connector with PG9 cable gland-HCC: 1/2 NPT conduit entry

Suffi x

+options: -H2 Adapter with 1/8 NPT thread -ME Manual Override-L14 Dust Excluder Solenoid Nut

SOLENOID-PILOT(ib) Intrinsic Safe{-XIF*: ATEX approved; Zones 1 & 2; (IIB) Category 1G}Approved Safety Barrier or isolator required.Max. pilot pressure 175 psi [12 bar]

G and -XIF* SA-4302-84-316-XIF*-.+.-D024(EXPilot type)

G and -XIF* SA-4322-84-316-XIF*-.+.-D024(INPilot type)


DetailA: M20 x 1.5 conduit entry.E: Cable gland for 6-12mm ø cable.F: 1/2 NPT conduit entry with adapter.

Suffi x



MM

•

.6917.5

1.6241.3

2.8271.6

3.3384.6

.94 23.9

1.38 35.1



ISO Connector

PG-9 Cable Entry -HC (1/2 NPT conduit entry -HCC)

Can be rotated through 360°

M5 Threaded EXH Port

Torque setting for tightening nut at assembly is 12 lbf - in (1.4 Nm)

1.69 43.0


.7519.1

.6917.5

1/2 NPT(XIFF)

1.38 35.1

.94 23.9

1.6241.3



M20 X 1.5(XIFA)

RSARSA USA

RN NL

•

CABLEGLAND(XIFE)

67439.indd 5.667439.indd 5.6 1/18/07 8:53:07 AM1/18/07 8:53:07 AM

6.1

MANUAL ACTUATORSDIMENSIONS SHOWN IN INCH

MM



Prefi x Suffi x

HAND BUTTONI SA-4302-86-316

HAND BUTTONwith 2 Panel Nuts

I and –43E SA-4302-86-316-43E(Reduces max. panel thickness from 0.90 to 0.58)HAND BUTTONWith Protective Boot

I and -NV93E SA-4302-86-316-NV93EI and -LOV*E HAND BUTTON

With Lockout Provision*Specify identifi cation detail. Detail

B: Lockout in exhaust position only SA-4302-86-316-LOVBE

E: Lockout in either offset position SA-4302-86-316-LOVEE

HAND LEVER(with protective boot)

L SA-4302-69L-316

67439.indd 6.167439.indd 6.1 1/18/07 8:53:12 AM1/18/07 8:53:12 AM

6.2

MANUAL COMBINATION ACTUATORSDIMENSIONS SHOWN IN INCH



Prefi x Suffi x

HAND BUTTON and ‘REVERSE’SPRING RETURN(Push to operate)

A and -136E CA-4302-86-316-136E

HAND BUTTON and SPRINGRETURN(Pull to operate)

A and -136PE CA-4302-86-316-136PE

HAND BUTTON and‘REVERSE’ SPRING RETURNwith MANUAL LATCH(Push to operate)

A and 136DRE CA-4302-86-316-136DRE

HAND BUTTON and SPRING RETURN With MANUAL LATCH(Pull to operate)

A and 181DRE CA-4302-86-316-181DRE

NOTE: Both actuator types with manual latch, listed above, can be provided with a protective boot per detail shown. Indicate by using suffi x “-294” in addition to all other suffi x designations.

HAND LEVER andSPRING RETURN withLATCHING DETENTAnd MANUAL RESET

A and -181CE CA-4302-65-316-181CELatches automatically when valve spool has been shifted on signal or manually against the spring. Unlatching allows the spring to return the valve spool automatically.

A and -181DE CA-4302-65-316-181DEUnlatching allows valve spool to be shifted manually or on signal. Spring returns valve spool automatically when signal is removed, and valve latches.

Note: Other latching sequences are available, consult factory for details.

67439.indd 6.267439.indd 6.2 1/18/07 8:53:16 AM1/18/07 8:53:16 AM

7.1

RETURN AND NON-ACTIVE DEVICESDIMENSIONS SHOWN IN INCH



Prefi x Suffi x

SPRING RETURN andLATCHING DETENT

A and -3358E CA-4302-65-316-3358EUnlatching allows valve spool to shift on signal. Spring returns valve spool automatically when signal is removed, and valve latches.

A and -3358AE CA-4302-65-316-3358AELatches automatically when valve spool shifts on signal. Unlatching allows the spring to return valve spool automatically.

NON-RETURNN SA-4302-71-316

(Empty cap – for manually operated valves or where combination actuators are used on one end of valve)

REVERSE SPRINGRETURN

R SA-4302-70-316(Spring pulls valve spool – for manually operated or pull type pilot valves)

SPRING RETURNS SA-4302-65-316

(Spring pushes valve spool — for all valves except pull type pilot and valves with combination actuators on one end of valve)

SPRING CENTERINGB SA-4302-72-316

(For 3 position manually operated valves)

THREE-DETENTU SA-4302-81-316


TWO-DETENTZ SA-4302-82-316


PLAIN END-CAPA and -33E CA-4302-32-316-33E

For position indication of valves with hand combination actuator on other end of valve. Also for tandem mounting of valves; a connector (for coupling of valve spools) and a mounting plate (for correct alignment of valves) can be supplied.

67439.indd 7.167439.indd 7.1 1/18/07 8:53:21 AM1/18/07 8:53:21 AM

8.1

*THREE-WAY (3 port-2 position & 3 port-3 position) BODY ASSEMBLIES*Two-way function may be provided by plugging the exhaust port (EA or 1) of Three-way Body Assembly.Body Assemblies with 2-outlet or 2-inlet function, see page 8.3.

1/4 NPT & 3/8 NPTDIMENSIONS SHOWN IN INCH



**3/2 (three-port 2-position)BODY ASSEMBLY

-3301- SA-3301-62-316 1/4 NPT-3401- SA-3401-72-316 3/8 NPT

**Body Assemblies for NC and NO functions are identical. For NC function the Return Device should be mounted at the “LH side”; for NO function at the “RH side”.

-3302--3402-

3/3 (three-port 3-position)BODY ASSEMBLY

-3303- SA-3303-62-316 1/4 NPT-3403- SA-3403-72-316 3/8 NPT

-3304- SA-3304-62-316 1/4 NPT-3404- SA-3404-72-316 3/8 NPT

Dimensions for 3/3 (Three-Port 3-position) Body Assemblies are the same as for 2-position Body Assemblies shown above.

NOTE: Product number designations and subassembly numbers that are listed are for EXPilot type valves; for INPilot type valves the third digit “0” is exchanged for “2.”

**

67439.indd 8.267439.indd 8.2 1/18/07 8:53:25 AM1/18/07 8:53:25 AM

8.2

*THREE-WAY (3 port-2 position & 3 port-3 position) BODY ASSEMBLIES*Two-way function may be provided by plugging the exhaust port (EA

1 ) of Three-way Body Assembly.Body Assemblies with 2-outlet or 2-inlet function, see page 8.4.

1/2 NPTDIMENSIONS SHOWN IN INCH



**3/2 (three-port 2-position)BODY ASSEMBLY

-3501- SA-3501-72-316 1/2 NPT

**Body Assemblies for NC and NO functions are identical. For NC function the Return Device should be mounted at the “LH side”; for NO function at the “RH side”.


-3503- SA-3503-72-316 1/2 NPT

-3504- SA-3504-72-316 1/2 NPT

Dimensions for 3/3 (Three-Port 3-position) Body Assemblies are the same as for 2-position Body Assemblies shown above.

NOTE: Product number designations and subassembly numbers that are listed are for EXPilot type valves; for INPilot type valves the third digit “0” exchanged for “2.”

67439.indd 8.367439.indd 8.3 1/18/07 8:53:29 AM1/18/07 8:53:29 AM

8.3

TWO-INLET or TWO-OUTLET FUNCTION (3/2 & 3/3) BODY ASSEMBLIES1/4 NPT & 3/8 NPTDIMENSIONS SHOWN IN INCH

MM




-7302- SA-7302-62-316 1/4 NPT

-7402- SA-7402-72-316 3/8 NPT

-8302- SA-8302-62-316 1/4 NPT

-8402- SA-8402-72-316 3/8 NPT


Body Assemblies with 3-position function: change fourth digit “2” in sub-assembly number into “3” for all ports blocked in center position.Dimensions for 3/3 (Two-Inlet &

Two-Outlet) Body Assemblies are the same as for 2-position Body Assemblies shown above.

NOTE: Product number designations and subassembly numbers that are listed are for ExPilot type valves; for INPilot type valves the third digit “0” is exchanged for “2.”

OUT 3

OUT 3

IN 2

1.0927.8

2.1955.6

.65616.7 .265 Ø

“LH side” “RH side”

2 HOLES

.79720.2

2.0050.8

.79720.2

VERSA®

N.J., U

SA &N

etherlands

IN 3

IN 1

OUT 2

1.0927.8

2.1955.6

.65616.7

.79720.2

2.0050.8

.79720.2

1/4” NPT or 3/8” NPT3 PORTS

N.J., U

SA &N

etherlands

1.5038.11.00

25.4.7519.1

1.5038.11.00

25.4.7519.1

1/4” NPT or 3/8” NPT3 PORTS

.265 Ø 2 HOLES

1/4” NPT =

3/8” NPT =

.6616.7.62

15.8

67439.indd 8.467439.indd 8.4 1/18/07 8:53:33 AM1/18/07 8:53:33 AM

TWO-INLET or TWO-OUTLET FUNCTION (3/2 & 3/3) BODY ASSEMBLIES1/2 NPTDIMENSIONS SHOWN IN INCH

MM




-7502- SA-7502-72-316 1/2 NPT

(A/2 = INLET; IN/3 + EA/1 = OUTLET)

-8502- SA-8502-72-316 1/2 NPT

(IN/3 + EA/1 = INLET: A/2 = OUTLET)


Body Assemblies with 3-position function: change fourth digit “2” in sub-assembly number into “3” for all ports blocked in center position.Dimensions for 3/3 (Two-Inlet &

Two-Outlet) Body Assemblies are the same as for 2-position Body Assemblies shown above.

NOTE: Product number designations and subassembly numbers that are listed are for ExPilot type valves; for INPilot type valves the third digit “0” is exchanged for “2.”

8.4

67439.indd 8.567439.indd 8.5 1/18/07 8:53:38 AM1/18/07 8:53:38 AM

FOUR-WAY (5 port-2 position & 5 port-3 position) BODY ASSEMBLIES1/4 NPT & 3/8 NPTDIMENSIONS SHOWN IN INCH

MM



5/2 (fi ve-port 2-position)BODY ASSEMBLY

-4302- SA-4302-61-316 1/4 NPT

-4402- SA-4402-71-316 3/8 NPT


-4303- SA-4303-61-316 1/4 NPT-4403- SA-4403-71-316 3/8 NPT

-4304- SA-4304-61-316 1/4 NPT-4404- SA-4404-71-316 3/8 NPT

Dimensions for 5/3 (Five-Port 3-position) Body Assemblies are the same as for 2-position Body Assemblies shown above.


8.5

3.5088.9

1.56 39.6

1.00 25.4.75

19.1

.6616.7 .265 Ø

.6616.7

.797 20.2 2.00

50.8 .797 20.2

1.31 33.3

1.75 44.5

.65616.7

.65616.7

1.31 33.3

1/4” NPT 5 PORTS

EB 5

IN 3

VERSA®

N.J., U

SA &N

etherlands

A2

EA 1

B4

3HOLES

67439.indd 8.667439.indd 8.6 1/18/07 8:53:40 AM1/18/07 8:53:40 AM

FOUR-WAY (5 port-2 position & 5 port-3 position) BODY ASSEMBLIES1/2 NPTDIMENSIONS SHOWN IN INCH

MM




-4502- SA-4502-71-316 1/2 NPT


-4503- SA-4503-71-316 1/2 NPT

-4504- SA-4504-71-316 1/2 NPT

Dimensions for 5/3 (Five-Port 3-position) Body Assemblies are the same as for 2-position Body Assemblies shown above.


8.6

67439.indd 8.767439.indd 8.7 1/18/07 8:53:45 AM1/18/07 8:53:45 AM

General DescriptionFor Emergency Shut Down Systems, a Manual Bleed Valve designated MSO2-3-316, and a Manual Block and Bleed Valve designated MS03-3-316.Both valves, constructed of 316 Stainless Steel, are used as panic valves to quickly depressurize the system to get immediate shut-down.Even from remote locations, they enable the user to shut-down various processes in case of an emergency.

Manual Bleed ValveThe valve MS02-3-316 is a 2-way valve that is closed during normal operation. By pulling the red panel knob out, the valve opens and the Emergency Shutdown system pressure is dumped to atmosphere. Although compact and light weight, an internal orifi ce of 3/8” assures quick shut-down of the system.Because the valve is designed to work as a bleed type device only, any backpressure to the exhaust port will cause the valve to shift and open the inlet gate as if the panel knob were pulled out.

Manual Block and Bleed ValveThe valve MSO3-3-316 is a 3-way valve that can be used in the Emergency Shutdown system loop. During normal operation the inlet port is open to the outlet port, and the exhaust port is closed. By pulling the panel knob out, the inlet port is blocked and the outlet port is opened to exhaust port, so that the downstream system pressure is dumped to the atmosphere.Like the manual bleed valve, any backpressure to the exhaust port of the valve will cause the valve to shift, dumping downstream pressure, as if the panel knob were pulled out.

Materials (Conform to NACE Standard MR-01-75)- 316 Stainless Steel- FKM (Fluorocarbon) ‘O’ ring seals- Plastic palm button

WeightsMS02-3-316 0.77 lbs. (.35 kg)MS03-3-316 1.00 lbs. (.45 kg)

PressuresOn inlet port :0 to 150 psi (10 bar) airOn exhaust port :0 psi (0 bar) backpressure

Porting & FlowValve ports 1/4 NPTMS02-3-316: Cv=2.0 (Kv=29)MS03-3-316: Cv=1.0 (Kv=14.5)

InstallationThe valves can be panel mounted. Panel hole is 1” (25.4 mm) ø

TWO-WAY (2/2) THREE-WAY (3-2)Block & Bleed Charge & Bleed

Product Number Knob Color Product Number Knob Color

MS02-3-316 Red MS03-3-316 Black

MS02-3-316-125B Black MS03-3-316-125R Red

316 STAINLESS STEEL ACCESSORIESManual Shut Off ValvesDIMENSIONS SHOWN IN INCH

MM

9.1

67439.indd 8.867439.indd 8.8 1/18/07 8:53:47 AM1/18/07 8:53:47 AM

10.1

Bleed Control Valves

316 STAINLESS STEEL ACCESSORIESShuttle Valve

Shuttle valves provide the simplest way of pressurizing and exhausting a pilot chamber through the actuation of any one of two or more three-way valves. If two remote stations are required, one shuttle valve (in place of a tee) is required between the two three-way valves. For each additional remote station another shuttle valve is required. The shuttle valve prevents pressure from the actuated valve from being exhausted through the unactuated valve.

In logic terms a shuttle valve is an ‘OR’ – function.A typical schematic is shown below:

DIMENSIONS IN INCHES (mm)

Materials (Conform to NACE Standard MR-01-75)Body: 316 stainless steelShuttle: 316 stainless steelSeals: FKM (Fluorocarbon)Screws: 316 stainless steel Weight: 0.33 lbs. (0.15 kg)Porting: 1/4 NPT

Pressures and FlowPneumatic: 3 to 200 psi (0.2 to 14 bar)Hydraulic: 3 to 500 psi (0.2 to 35 bar) Cv=0.5 (Kv = 7)

InstallationPreferably with the centerline of the two inlet ports horizontal. As shown in the drawing above.

Symbol Product Number SV-3-316


The VERSA Bleed Control Valve has a precision machined needle that provides an economical, effective fl ow control in pneumatic applications. They can be threaded into the ex-haust port of any VERSA directional control valve to provide speed control.The fl ow area, through which the air passes to the atmosphere, can be fi nely adjusted by screwing the needle in or out. After the Bleed Control Valve has been adjusted to suit, it can be securely locked at its setting with the lock nut provided.

Materials (Conform to NACE Standard MR-01-75)316 stainless steel

Pressures0 to 200 psi (0 to 14 bar) air

Symbolvalve exhaust port

Product NumberBC-3-316 1/4 NPTBC-4-316 3/8 NPTBC-5-316 1/2 NPTBC-6-316 3/4 NPT

67439.indd 10.167439.indd 10.1 1/18/07 8:53:50 AM1/18/07 8:53:50 AM

316 STAINLESS STEEL ACCESSORIESQuick Exhaust Valves (See Bulletin ACC for Electric Quick Exhaust Valves)


A Quick Exhaust Valve is a 3/2 (three-way) valve with extra large exhaust orifi ce, to be fi tted directly at a cylinder port connection.When pressure decreases at the inlet of the Quick Exhaust Valve, the outlet is automatically opened to the exhaust and the cylinder is quickly depressurized.

Materials (Conform to NACE Standard MR-01-75)Body: 316 stainless steelSeals: FKM (Fluorocarbon) ‘O’ ring seals and CR

(Neoprene) coated Nylon fl apper.Other parts: 316 Stainless Steel

Weights SymbolQE-3-316 0.81 lbs (0.37 Kg)QE-5-316 2.16 lbs (0.98 Kg)

QE-6-316 2.44 lbs (1.11 Kg)

Pressures5-150 psi (0.34 to 10 bar)

Temperature:QE-3-316 & QE-5-316:-20°F to 200°F (-29°C to 93°C)QE-6-316: -30°F to 350°F (-34°C to 177°C)

PortingType Inlet/Outlet ExhaustQE-3-316 1/4 NPT 3/8 NPTQE-5-316 1/2 NPT 3/4 NPTQE-6-316 3/4 NPT 1 NPT

FlowType IN to CYL CYL to EXQE-3-316 Cv=3.0(Kv=43.5) Cv=3.3 (Kv=48)QE-5-316 Cv=3/8 (Kv=55) Cv=8.8 (Kv=128)QE-6-316 Cv=4.6 (Kv=66) Cv=13.6 (Kv=195)

Product NumberQE-3-316 1/4 NPTQE-5-316 1/2 NPTQE-6-316 3/4 NPT

Dust Excluders may be threaded into the exhaust ports in order to keep out dirt or dust in the atmosphere or surrounding the valve, that might enter through an other-wise open port.

Materials (Conform to NACE Standard MR-01-75)Body: 316 Stainless StellSeal: CR Chloroprene (Neoprene)

Pressures0 to 200 psi (0 to 14 bar)

InstallationDust Excluders are preferably mounted in a vertical position with the wide outlet opening down.

Symbol Valve exhaust port

Dust Excluders DIMENSIONS IN INCHES (mm)

Product NumberDE-3-316 1/4 NPTDE-4-316 3/8 NPT

DE-5-316 1/2 NPTDE-6-316 3/4 NPT

10.2

QE-6-316 Consult Factory

67439.indd 10.267439.indd 10.2 1/18/07 8:53:52 AM1/18/07 8:53:52 AM

10.3

316 STAINLESS STEEL ACCESSORIESStatus Indicator


General DescriptionSome applications require visual indication, when a system is pressurized or when a system has lost pressure. The Versa Status Indicator provides such a display within a stainless steel shell that can be mounted as an integral part of a panel. Viewing the panel provides the operator with an instantaneous evaluation of the pressure condition in the system or systems being monitored.

Functional DescriptionVersa’s Status Indicator provides visual indication of pressure in a system. The standard product displays a green fi eld when a minimum of 8 psi (0.55 bar) to a maximum of 200 psi (14 bar) is present. Complete loss of pressure causes the indicator to display a red fi eld, marked with the recognition character “R”. Other fi eld colors are available. See TYPES below.

Materials:Body and internal wetted metal parts – 316 Stainless Steel+Working seals – FKM (Fluorocarbon)Lens-polycarbonate (seal to prevent moisture intrusion), resistant to ultraviolet rays

Porting:1/8 NPT pressure supply port

PressuresOperating pressure range: 0 to 200 psi (14 bar) air*

MountingPanel hole opening 1” (25.4mm) øCan be mounted in any orientation with maximum panel thickness 0.50” (12.7mm) with one panel nut; maximum panel thickness 0.21” (5.3mm) with two panel nuts. (suffi x -43E).

Panel Hole Opening Required : 1 Ø(25.4)

1/8-27 NPTPressure Supply

Port

2.48(63)

1.5(38)

Type/WeightsOperating Pressure Range

Product NumberDepressurized

0 psi (0 bar)Pressurized

8 psi (0.55 bar) to 200 psi (14 bar) Weights

SI-2-316SI-2-316-403GRSI-2-316-403YGSI-2-316-403GY

Red (R)Green (G)Yellow (Y)Green (G)

GreenRedGreenYellow } 0.50 lbs. (0.23 kg)

*For hydraulic service consult factory.†Conforms to NACE standard MR-01-75

67439_COVS No Varn.indd 10.367439_COVS No Varn.indd 10.3 2/23/07 9:00:44 AM2/23/07 9:00:44 AM

www.versa-valves.com

Versa Products Company, Inc., 22 Spring Valley Road, Paramus, New Jersey, USA 07652 • 201/843-2400 FAX: 201/843-2931Versa BV., Prins Willem Alexanderlaan 1429, 7312 GB Apeldoorn, The Netherlands • 01131-55-3681900 FAX: 01131-55-3681909

SERIES “B” VALVES:1/8” NPT, 3/16” (4.7mm) Orifi ce. Two- & Three-Way. Brass & SS Construction. Manual, Pilot & Cam Actuation. Pneumatic Service Vacuum to 200 psi (14 bar). Bulletin B.

SERIES “B-316”, “B-900” & “B-550” AUTOMATION

AND CONTROL VALVES & COMPONENTS FOR

PROCESS CONTROL:Suitable for Offshore, Process Control, Material Specs Meet NACE MR-01-75. Fluorocarbon Seals, 1/4” NPT, 3/16” (5mm) Orifi ce. Three-Way. Solenoid/Pilot, Remote Pilot, Mechanical, Manual & Many Special Actuators. Main Supply Reset Valves; First Out Indicating Valves. Pneumatic Service Vacuum to 200 psi (14 bar). Bulletin B316

SERIES “C” VALVES:10-32 (M5), 1/8” NPT OR G1/8”, 1/4” NPT OR G1/4, 0.6 to 7mm Orifi ce. Three- & Four-Way, Multi-purpose. Individual Mount, Stacking, or Manifold Mounted. Aluminum, SS & Nylon Construction. Solenoid/Pilot, Pilot, Manual & Mechanical Actuation. Pneumatic Service Vacuum to 115 psi (8 bar). Bulletin C.

SERIES “E” VALVES:1/8” NPT & 1/4” NPT. 1/32” (0.8mm) thru 1/4” (6.4mm) Orifi ce. Two- & Three-Way, Directional, Multi-Purpose. Sideported, and Manifold Mounted. SS or Aluminum Construction. Direct Solenoid Actuation, including LOW WATT. Pneumatic & Hydraulic Service Vacuum to 500psi (35 bar). Bulletin E.

SERIES “K” VALVES:Compact Air Management System. ¼” NPT or G1/4”, 4.7mm & 6.5mm Orifi ce. Two-, Three-, Four- & Five-Way, Selector, Diverter. Manifold Mounted, Integrated Circuitry, Aluminum Construction.

Fluorocarbon Seals. Solenoid/Pilot, Remote Pilot, Cam & Manual Actuation. Pneumatic Service Vacuum to 175 psi (12 bar). Bulletin K.

SERIES “H” VALVES:High pressure hydraulic valves: High pressure valves for the Oil & Gas Industry; to 10,000 psi operating pressure, 316 stainless steel construction, leakproof, balanced dynamic ceramic sealing, O ring static seals, modular design, manifold mounting. Bulletin H

SERIES “V” & “T” VALVES:1/8” thru 1-1/4” NPT or G, Full Ported, Two-, Three-, Four- & Five-Way, Selector, Diverter. All types of Actuation. Forged Brass Construction. Pneumatic Service Vacuum to 200 psi (14 bar), Hydraulic Service to 500 psi (35 bar). Bulletin VT.

SERIES “V-316” STAINLESS STEEL VALVES:Suitable for Offshore, Process Control, Material Spec Meet NACE MR-01-75. Fluorocarbon Seals. 1/4”, 3/8”, 1/2” NPT, Full Ported. Two-, Three-, Four- & Five-Way. Selector. Diverter. All Type of Actuation. Pneumatic Service Vacuum to 200 psi (14 bar). Bulletin V316.

SOLENOID VALVES FOR THE PROCESS CONTROL

INDUSTRY:Complete Range of Stainless Steel, Brass or Aluminum Constructed Valves, 1/8” NPT through 1 NPT. Direct NAMUR Mount & Bodyported Styles. Latching Manual Reset, Lockout Valves, Redundant Valves. Bulletin PCg.

ACCESSORIES:Shuttle Valves, Bleed Control Valves, Dust Excluders, Foot Guards, Bleed Valves, Quick Exhaust Valves, Status Indicators. Bulletin ACC.

IF YOU HAVEN’T FOUND THE VALVE YOU NEED,YOU HAVEN’T ASKED US.Versa Valves… designed, built, and tested

to meet your air requirements.

WARNINGS REGARDING THE DESIGN APPLICATION,

INSTALLATION AND SERVICE OF VERSA PRODUCTS

The warnings below must be read and reviewed before designing a system utilizing, installing, servicing, or removing a Versa product. Improper use, installation or servicing of a Versa product could create a hazard to personnel and property.

DESIGN APPLICATION WARNINGSVersa products are intended for use where compressed air or industrial hydraulic fl uids are present. For use with media other than specifi ed or for non-industrial applications or other applications not within published specifi cations, consult Versa.

Versa products are not inherently dangerous. They are only a component of a larger system. The system in which a Versa product is used must include adequate safeguards to prevent injury or damage in the event of system or product failure, whether this failure be of switches, regulators, cylinders, valves or any other system component. System designers must provide adequate warnings for each system in which a Versa product is utilized. These warnings, including those set forth herein, should be provided by the designer to those who will come in contact with the system.

Where questions exist regarding the applicability of a Versa product to a given use, inquiries should be addressed directly to the manufacturer. Confi rmation should be obtained directly from the manufacturer regarding any questioned application prior to proceeding.

INSTALLATION, OPERATION AND SERVICE WARNINGSDo not install or service any Versa product on a system or machine without fi rst depressurizing the system and turning off any air, fl uid, or electricity to the system or machine. All applicable

electrical, mechanical, and safety codes, as well as applicable governmental regulations and laws must be complied with when installing or servicing a Versa product.

Versa products should only be installed or serviced by qualifi ed, knowledgeable personnel who understand how these specifi c products are to be installed and operated. The individual must be familiar with the particular specifi cations, including specifi cations for temperature, pressure, lubrication, environment and fi ltration for the Versa product which is being installed or serviced. Specifi cations may be obtained upon request directly from Versa. If damages should occur to a Versa product, do not operate the system containing the Versa product. Consult Versa for technical information.

LIMITED WARRANTY DISCLAIMER AND

LIMITATION OF REMEDIES

Products sold by Versa are warranted to be free from defective material and workmanship for a period of ten years from the date of manufacture, provided said items are used in accordance with Versa specifi cations. Versa’s liability pursuant to that warranty is limited to the replacement of the Versa product proved to be defective provided the allegedly defective product is returned to Versa or its authorized distributor.

Versa provides no other warranties, expressed or implied, except as stated above. There are no implied warranties of merchantability or fi tness for a particular purpose. Versa’s liability for breach of warranty as herein stated is the only and exclusive remedy and in no event shall Versa be responsible or liable for incidental or consequential damages.

67439_COVS No Varn.indd 10.467439_COVS No Varn.indd 10.4 2/23/07 9:00:45 AM2/23/07 9:00:45 AM

Versa 3501

Documents

Transcript of Versa 3501