UDA Building and Planning Regulations

Ministry of Defence and Urban Development

Urban Development Authority

Enforcement Division7th Floor

“Sethsiripaya”Battaramulla

0112 – 872616www.uda.lk

[email protected]

Declaration of areas as “Development Area” by

Order of the Minister under Section 3 of Act.

No. 41 of 1978

Declaration of areas as “Development Area”

2/6/2012 Enforcement Division 3

THE URBAN DEVELOPMENT AUTHORITY LAW

• Law No. 41 of 1978 – Section 8

• Planning & Building Regulations

– Section 21• 1986 Extraordinary Gazette No. 392/9• 2009 Extraordinary Gazette No. 1597/8• 2011 Extraordinary Gazette No. 1701/13


Preliminary Planning Clearance and Approval of Plans Regulation 10

(1) The Preliminary Planning Clearance shall be in writing and may include such restrictions and conditions as may be imposed.

(2) It shall be valid for a period of one year(3) The Preliminary Planning Clearance will not

constitute a permit and shall not entitle the applicant or any person to commence or carry out any Development Activity.


• Under Section 8J of the Act. No. 4 of 1982 (amended) & Regulation 3 of Extraordinary Gazette No. 392/9 - 1986– Application for obtaining a Development Permit for

Sub-Division Land in Schedule (I) Form A– Application for obtaining a Development Permit for

Building in Schedule (I) Form B

• Schedule V of Extraordinary Gazette No. 1597/8 - 2009– Fees specified in Schedule (V)

Submission of Plans


Submission of Plans Cont.

• Regulation 6 - Scale of Plans– Survey plan or Blocking out plan 1:1000 (not less than)– Floor Plans 1:100 – large building 1:200

• Regulation 4– Prepared & signed by Qualified Person– Signed by Owner of the Site or Premises– Submitted in 3 Copies


Qualified Person• “qualified person” means any person required to

approved or certify any development activity in terms of regulations 8, 9,61,67 and 70 of these regulations and who is specified in Column 1V of Schedule VI to these regulations. (No. 1597/8 – 2009)

– Town Planner• Corporate member of the Institute of Town Planners Sri Lanka

– Licensed Surveyor and Leveler• Surveyors’ Institute Sri Lanka

– Charted Architect or Architect registered with the Architect Registration Board

• Institute of Architect Sri Lanka– Charted Civil, Structural, Electrical, Mechanical, Building Service

Engineer• Institute of Engineers Sri Lanka


Schedule VI of Extraordinary Gazette No. 1597/8 - 2009

No. Extent of Land Specific Task Qualification/Designation

01 Exceeding 0.5 Hectares

Site Layout Plan Corporate Member Institute of Town Planer

Regulation Compatibility

Corporate Member Institute of Town Planer

Preparation of Subdivision Plan

Licensed Surveyor & LevellerSurveyors’ Institute

02 Less than 0.5 Hectares

Site Layout Plan & Subdivision Plan

Licensed Surveyor & LevellerSurveyors’ Institute

Regulation Compatibility


03 If the development activity involves engineering works (Construction of roads, culverts, drains)

Charted Civil EngineerInstitute of Engineers

04 If the development activity involves a subdivision or amalgamation of land Exceeds 0.5 Hectares



Building CategoryRegulation 8 (1), 8 (2) & 8 (3) & New Reg. 2009 (1)

Building Category No. of FloorsCategory A (High Rise) G + 4 & above

Category B (Low Rise) Less than G + 3- A wall or Column is situated on the boundary- A basement – roofs, foundations, beams & other related parts- A pile or raft foundation- A roof span exceeding ten meters- Public Assembly or Public Building- A wind sensitive buildings (Warehouse & Factories)- Any other buildings not covered under Category A & C

Category C (Low Rise)Residential UseCategory C I(i) (<500 m2)Non-Residential UseCategory C I (ii) (<300 m2)Residential UseCategory C II (i) (<400 m2)Non-Residential UseCategory C II (ii) (<200 m2)Residential UseCategory C III (i) (<200 m2)Non-Residential UseCategory C III (ii) (<100 m2)

Less than G + 2(Not fall under Category B)


Nature of Development Activity

Specific Task Requiring Approval of Qualified Person

Qualification/Designation Required of Qualified Person

5. If the development activity relates to buildings of sub category A and B

1. Architectural Plan

Chartered Architect or Architectural Licentiate. Registered with the Architects Registration Board

2. Structural Design Plan along with design calculations

Chartered Civil, Structural Engineer Institute of Engineers Sri Lanka

3. Service PlansElectrical, Civil, Structural, Building Services or Mechanical Engineer

4. Detailed Plan of Air conditioning or Mechanical Ventilation

Chartered Mechanical or Electrical Engineer


Nature of Development Activity Extent of Floor Area

Specific Task Requiring Approval of Qualified Person

Qualification/Designation Required of Qualified Person

1. If the development activity relates to buildings of sub category CI of Category C

Residential up to 500 sq.m. Architectural Plan

Chartered Architect or Architectural Licentiate. Registered with the Architects Registration Board

Non-Residential up to 300 sq.m.

Structural Design Plan along with design calculations

Chartered Civil, Structural Engineer Institute of Engineers Sri Lanka

Service PlansElectrical, Civil, Structural, Building Services or Mechanical Engineer

Detailed Plan of Air conditioning or Mechanical Ventilation

Chartered Mechanical or Electrical Engineer

2. If the development activity relates to building of sub category CII of Category C

i. Residential up to 400 sq.m.

Designing and certification of Plans

Draught-Person (Building) at NVQ, Level V

ii. Non-Residential up to 200 sq.m.

Structural Designs, service designs, air conditioning and artificial ventilation

Relevant Members of the Sri Lanka Institute of Engineers

3. If the development activity relates to building of sub category CIII of Category C

i. Residential up to 200 sq.m.

A Certificate confirming that the building has been constructed with structural stability according to the approved plan and building permit

Builder/Owner or any other person acceptable to UDAii. Non-Residential

up to 100 sq.m.

Part I, Schedule VII of Extraordinary Gazette No. 1597/8 - 2009

USED AND TYPES OF BUILDINGS

Uses Type of Buildings

Residential Including Houses, Multiple Dwellings, Apartments, Home for Elders

CommercialIncluding Office Building, Hotels, Motels, Guest House, Public Lodging, Shopping Centers, Supermarkets, Restaurants, Car Parks

Industrial Including Factories, Workshops, Warehouse, Industrial Establishments, Infrastructure Services Center

Institutional Government Buildings, Semi-Government Buildings and Other Public Buildings

Part II, Schedule VII of Extraordinary Gazette No. 1597/8 - 2009

MINIMUM EQUIVALENT RAINWATER HOLDING PROVISION REQUIREMENT

Annual Rainwater Band (mm)

Minimum Volume (m3) required per 100 m2 of roof plan area and hard paved area

ResidentialCommercial Industrial Institutional

Domestic Apartments/ Condominiums

7050 - 1000 1.5 2.5 5 8 10

1000 - 1500 1.5 2.5 3 8 10

1500 - 2000 1.5 2.5 3 5 10

2000 - 2500 1.5 2.5 3 3 5

2500 - 3000 1.5 2.5 2 2 3

3000 - 4000 1.5 2.5 1 1 2

4000 - 5000 1.5 2.5 0.5 1 1

5000 - 6000 1.5 2.5 0.5 0.5 0.5

Calculation of Required Rainwater Holding Provision

Required Equivalent Rainwater = Minimum Volume X Total Roof Plan Area Holding Provision (m3) 100 and Paved Area

Calculation of Required Equivalent Rainwater Holding Provision (m3) for Residential Domestic Unit

Required Equivalent Rainwater = 1.5 X 200 m2

Holding Provision (m3) 100

= 3 m3


Any person aggrieved by the decision of the Authority refusing to issue a permit may within 30 days of receiving notice of such refusal appeal to the Minister.

Appeals Against RefusalRegulation 11


• The Authority may prohibit the felling, lopping, or willful destruction of any tree, group of trees or vegetation or altering any significant landscape feature of the area.

• The authority may direct an owner to landscape the site of development and maintain it with planting in the manner approved by it.

Landscape and Tree Preservation

Regulation 35


Certificate of ConformityRegulation 67 of Gazette No. 392/9 - 1986 and

Schedule V of Gazette No. 1597/8 - 2009

The land development or sub-division of land:-(a) (i) a Certificate from a qualified person stating that

the sub-division has been carried out as specified in the approved plans and permit;

(ii) a Certificate from a qualified person where engineering works are involved in development activities such as the construction of roads, culverts and drains, stating that the development works carried out in conformity with the specifications of the permit.


The construction of buildings falling within Category A:-(b) (i) a Certificate from Charted Architect the

development has been carried out under his supervision in accordance with the approved Plan and Permit

(ii) a Certificate from Charted Civil Engineer, all kind of structure works have been carried out accordance with approved plans and permit. Under his supervision and the buildings are structurally safe.

(iii) a Certificate from Charted Electrical, Sanitary, Refrigeration Engineer that systems have been installed under their supervision accordance with the approved plans and all safety requirements.

Certificate of Conformity Cont….


The construction of buildings falling within Category B,CI, & CII:-(c) a Certificate from Charted Architect or Charted

Engineer the works have been carried out under their supervision in accordance with the approved Plan and Permit, the building is structurally safe.

The construction of buildings falling within Category CIII:-(d) a Certificate from builder or the owner where

the owner is also the builder the works have been carried out accordance with the approved Plan and Permit, the building is structurally safe.

Certificate of Conformity Cont….


Open Spaces Around BuildingsPlot Coverage

Regulation 25 & Form E of Schedule III

Plot Coverage = Ground Floor Plinth AreaLand Area

Dwelling Units, Hotels, Hostels, Guest Houses & Public Assembly Buildings

Offices, Shops, Other Commercial & Industrial Buildings

x 100

66 2/3 %

80 %

Land Extent 150 sq.m. (6P)

Dwelling Units, Hotels, Hostels, Guest Houses & Public Assembly Buildings

Buildable Area (Plinth Area) = 100 sq.m.

Land Extent 300 sq.m. (12P)Offices, Shops, Other Commercial

& Industrial BuildingsBuildable Area (Plinth Area) = 240 sq.m.


Splaying of Street CornersRegulation 32

W2

W1

Centre LinesRoad

Land Plot

Road

Any buildings including boundary walls or fences to be erected at the corner of two streets be rounded off or splayed


What is Rear Space?The Space father from any Street

If more than one access, the rear space shall be the space which is fatherst from the widest street.

Rear Space = r (Where W is more than W1)

For irregular shaped blocks, authority may decide where appropriate.

W1

W

r

Road

Roa

d

Rear SpaceRegulation 26 (2) & 26 (4)


Open SpaceResidential

Regulation 22 (1)If the Land to be Sub Divided is more than 1 Ha., keep 10 % Open Space (Excluding Roads)

for

Community Recreation


Turning CircleRegulation 16 (4)

9 mNeed 9m Diameter Turning Circle

Mor

e th

an 3

0 m

Width Less Than 9m

IF,

Road width < 9m&

Road Length > 30m

Road


Access to Residential Units

• Regulation 16 (2) (a) & Form A of Schedule III

1 2 3

Number of Dwelling Unit Served Minimum Width

(Metres)

Maximum Length

(Metres)Under 4 dwelling unite 3.0 50

More than 4 but not more than 8 dwelling unite 4.5 100

More than 8 but not more than 20 dwelling unite 6.0 -

More than 20 dwelling unite 9.0 -


AccessResidential Units

Regulation 16 (2) (a) & Form A of Schedule III

3m wide & 50m or less in length road serves

Max. 4 Lots

Main Road

3m

4

1

23

50m




4.5m wide & 100m or less in length road serves

Max. 8 Lots

Main Road

4.5m7

1

4

5

100m

2

36

8




6m wide & road serves

Max. 20 Lots

12

3 45

678

9

1011

12

1314

1516

17 18

1920

6m

Plot SizePublic Assembly and Public Buildings

Regulation 17 (1) & Form C of Schedule III

Minimum Plot Size = 300 sq.m. (12p)

for

GG+1G+2G+3


Plot SizeBuildings Other than

Public Assembly and Public BuildingsRegulation 17 (1) & Form C of Schedule III

Minimum Plot Size = 150 sq.m. (6p)

for

GG+1G+2G+3


Plot SizeHigh Rise Buildings

Regulation 27 (1)

Minimum Plot Size = 1000 sq.m. (40p)Shortest Side of the Site = 20m.

for

G+4 or more


Road FrontageBuildings other than

Public Assembly and Public BuildingsForm C of Schedule III

Minimum Frontage = 6 m.

for

GG+1G+2G+3

6 m


Road FrontagePublic Assembly and Public Buildings

Regulation 17 (1) & Form C of Schedule III


for

GG+1G+2G+3

12 m


Road FrontageHigh Rise Buildings

Regulation 27 (1)

for

G+4 or more


20 m


Road FrontageDead End

Regulation 17 (2)

Lot 1

Lot 2

Road3m


yx

6mRoad

Street Edge

Ramp

Parking Area

Gradient for RampsRegulation 31 (5) & 31 (6)

Maximum Gradient for Ramp (y : x) = 1 : 8

Ramp should start at a distance of 6m from the street edge


Access Road

High TensionLow Tension4.5 m

2.5 m

Clearance from Electric LinesRegulation 38


Clearance from Electric LinesRegulation 38

High TensionLow Tension

1.5 m

2.5 m

Access Road


Floor Area RatioRegulation 15 (1)

Floor Area Ratio (FAR) = Ground Floor Area of all BuildingLand Area

Max. Floor Area Ratio on Any Site = 1 : 2.75

In special cases FAR may be permitted to exceed up to 30 % subject to service charge considering the infrastructure availability and land values of the area.

Land Extent 150 sq.m. (6P)Maximum Floor Area = 412.5 sq.m.


Building HeightsLow rise BuildingsRegulation 18 (2)

Maximum Height of the Building is 2h or 15 m whichever is Less

2h or 15

hAccess Road


Building HeightsHigh rise BuildingsRegulation 29 (1)

Maximum Height of the Building is 2h

2h

hAccess Road


Building HeightsBuildings Height shall be ignored

Regulation 18 (4)

IfLift or Motor Room height 6m (h < 6m) & extent < 55 sq.m. Staircase Room height 5m (h <5) & extent < 25 sq.m.Water Tank height 1.5m (h < 1.5m)shall be ignored.

Access Road

h


Disability Access to Public BuildingsSupreme Court Order – SC(FR) 221/2009

• Entry & Exit to the Buildings

• Verandahs• Stair Cases• Sloping Roads• Lifts• Toilets & Bath

Rooms

• Parking Facilities• Internal Roads in

Office Complex• Roads &

Pavements• Road Name Boards

& Advertisement• Light Signals• Electric Post &

Telephone Post etc.


Internal Heights (Minimum)Toilets, Bathrooms & Corridors

Regulation 42 (1)

2.1 m2.1 m

Corridor

Bath RoomToilet

GL


Internal Heights (Minimum)Rooms other than Toilets, Bathrooms & Corridors

Regulation 42 (2)

2.7 m 2.4 m

Bed RoomBed Room

Living

2.7 mBeams

GL


Internal Heights (Minimum)Air Conditioned Rooms

Regulation 42 (3)

2.4 m 2.4 mBed Room

Living Room

GL

2.4 mBed Room


Internal Heights (Minimum)Sloping RoofRegulation 43

Mid Point

Bed RoomLiving

GL

2.1 m2.4 m

In case of Sloping Roof the height at the Mid Point should be 2.4 m and the lowest height at any point should be 2.1 m


GLGLh

Basement

Ground Floor

1/3 h

2/3 h

Ventilation

Natural Light & VentilationBasement Rooms

Regulation 52


Natural Light & VentilationSources

Regulation 45 (1) & 45 (2)

Every room in a building shall be provided with natural light and ventilation by means of Windows, Doors, or any other

approved openings

Natural Light & Ventilation can be obtained from;

A Public Street or a Street on which the owner or the building has a Right of Way;

A Courtyard or Open Space located in the Building Site

2/6/2012 Enforcement Division 50Site Boundary

63 1/2o

GL

Standard Light Plane

G

G + 1G + 2

G + 3

G + 4G + 5

Natural Light & VentilationStandard Light Plane

Regulation 51 (1)

2/6/2012 Enforcement Division 51Site Boundary

63 1/2o

GL


G

G + 1G + 2

G + 3

G + 4G + 5

x

Sunshade or Eave

Maximum width of Projection of Sunshade or Eave (x) = 1 m

Natural Light & VentilationStructures Allowed to Intersect

Standard Light PlaneRegulation 51 (1)


Site Boundary

63 1/2o

GL


G

G + 1

G + 2

x

Requirements

Minimum width (x) = 2.25 mThe Face of Building shall not intersect the Standard Light Plan

Open Space should exclusively attached to the Building

In case of Toilets & Bathrooms = 1 m Minimum width of Open Space

Natural Light & VentilationExternal Open Space for Buildings

Regulation 51 (2) & (3)


Site Boundary

63 1/2o

GL


G

G + 1

G + 2

x1x2

x3

h

h1

h2

.

.

.

.

.h/2

.

.

.

.

.h

15

12

9

6

3

X (m)Height (m)

X = Space required for light & ventilation in relation to h

Natural Light & VentilationExternal Open Space for Buildings

Regulation 51 (2) & (3)


Natural Light & VentilationBath Room &Toilets

Regulation 48 (1) & Form G of Schedule III

100 % of the Opening should be Openable

AB =

10

Area of Opening = B

Floor Area = A

Toilet

Ventilation


Floor Area = A

Open Area = B

Ventilation

Garage 50 % of the Opening should be Openable

AB =

10

If more than 5 vehicles shall have at least 50 % of the area of two or more sides of the Room as openings to allow for cross ventilation

Natural Light & VentilationVehicle Parking Garage



Ventilation

Floor Area = AFactory

Window Area = B

50 % of the Window should be Openable

AB =

10

Natural Light & VentilationFactories & Warehouses



Ventilation

Floor Area = ARoom

Window Area = B

50 % of the Window should be Openable

AB =

7

Natural Light & VentilationAll other Rooms



d

Open Area = B

Ventilation

Room 1Room 1 & Room 2 could be considered as one room and the window are should be accordingly provided

Room 2d/2

Natural Light & VentilationSpecial Provision

Regulation 49


Ventilation 3 m

3 m

10 m

Ventilation Ventilation

10 m10 m

Perpendicular Distance

Maximum Distance allowed from the opening = 10 m

&Maximum perpendicular distance allowed from = 3 m the edge of the opening

Natural Light & VentilationBuildings other than Factory & Warehouses

Regulation 46 (1)


Ventilation 3 m

3 m

12 m

Ventilation Ventilation

12 m12 m

Perpendicular Distance

Maximum Distance allowed from the opening = 12 m

&Maximum perpendicular distance allowed from = 3 m the edge of the opening

Natural Light & VentilationFactory & Warehouses

Regulation 46 (2)


Floor Area & Internal DimensionsHabitable Room in Dwelling Units

Regulation 39 & Form 1 of Schedule III

Kitchen

Additional RoomArea = 7.5 sq.m.

First RoomArea=8.5 sq.m.

Living

Bath Room

1.8 m

2.4 m

2.4 m

If there are only one room in a Dwelling unit

Minimum Width = 3.0 mMinimum Area = 11 sq.m.

If there are more than one room in a Dwelling unit

First RoomMinimum Width = 2.4 mMinimum Area = 8.5 sq.m.

Additional RoomMinimum Width = 2.4 mMinimum Area = 7.5 sq.m.

Kitchen Living

Bath Room

First RoomArea=11 sq.m.

3 m


1.2 m

0.9

m

1.2 m

0.9

m

Floor Area & Internal Dimensions

Habitable Bath, Toilet, and Combined Toilet & BathRegulation 40 & Form J of Schedule III

BathToilet

1.7 m

0.9

m

Combined Toilet & Bath


Rear SpaceRegulation 26 (1)

Rear Space = 2.25 m.

Maximum 2 Storeys

GG + 1

2.25m

Access Road



Rear Space = 3 m.Maximum 4 Storeys

GG + 1G + 2G + 3

OrBuilding Height Less than 15 m

3 m

Access Road


Rear SpaceHigh Rise Buildings

Regulation 30 (2)

for

G + 4 or More

Rear Space (X) = Height of the Building4

X

Access Road


Side SpaceHigh Rise Buildings

Regulation 30 (1)

Side Space (d) = Height of the Building4

or

5.5 m

Whichever is less

(At least on one side)

Access Roadd


Building HeightsExisting Lot

Regulation 18 (1)

If

Extent Less than 150 sq.m. (6p)

& / or

Width Less than 6 m

Max. Height of the Building = 7.5 m

or

Max. Number of Floors = 2

Less than 6 m

Building

Road


Open SpaceResidential

Regulation 22 (1) (b) (1996 Amendment)

If

Minimum Plot Size is 1012 sq.m. (40p)

&

Development is Limited to 2 Units per Lot

10% Open Space is not required, until further sub division

12

1

2

12

12

12

Main Road

2/6/2012 Enforcement Division 69Main Road

9m

Open SpaceCommercial or Industrial

Regulation 22 (1) (a) (1996 Amendment)

If

Plot Size is 2024 sq.m. (80p) or More

&

Access Road is 9m or More

10% Open Space is not required, until further sub division


Building HeightsNon Site Situated in a Corner

Regulation 18 (3)

If d is less than 20 Max. Height = 2x

If d is more than 20m Max. Height = 2y

Where w1 > w2

d

x

yW2

W1

BuildingSite



Rear Space is not required, if the rear of the Site abuts on to a Public Street not less than 6m in width

Access Road

Road at Rear

Building Line If any

6 m

Building

Site

Side SpaceRegulation 26 (5)

If a Space is provided for maintenance of the building, the Space should be Min. 80 cm

Access Road

BuildingBuilding

80 cm


The Developments to be in Conformity with the Permit

Regulation 12

(1) No development Activity shall be commenced or carried out in contravention of the Development Permit.

(2) The development permit may be revoked by the authority if there is :-

(a) a beach of a term or condition of the permit(b) a contravention of the provision of these regulations(c) A misrepresentation of facts in the application, plans

or other documents submitted by the applicant, or(d) Failure to submit plans and other particulars under

regulation 9.

T

R

W

StaircaseHabitable Bath, Internal Stairs Serving one Upper Floor only

Regulation 44 (1) & Form K of Schedule III

Widthe (w) = 75 cm

Min Head Room =200 cm

Riser (R) = 19.0 cm

Tread (T) =22.5 cm

T

R

WStaircaseStairs in Public Buildings


Widthe (w) = 105 cm


Riser (R) = 17.5 cm

Tread (T) =22.5 cm

T

R

W

StaircaseStairs in All Other Buildings


Widthe (w) = 90 cm


Riser (R) = 17.5 cm

Tread (T) =22.5 cm

h

Minimum Height of Hand Rail (h) = 0.9 m

StaircaseHand Rails

Regulation 44 (2) (b)

Dimensions of StallsRegulation 31 (2) & Section 3 (b) (7) of Schedule III of 1994 Amendment

0.6 m

2.25

m

0.6

m

2.25 m

3.0 m

8.0

m

2.4 m

4.8

m 5.4 m

2.4

m

Angle Parking

ParallelParking

Angle/ParallelParking

Angle Parking

ParallelParking

Motor Cycles Lorry Other Vehicles

Width of AislesParallel Parking

Regulation 31 (3) & Form F of Schedule III

Aisle (Access) Aisle (Access)3.6 m 3.6 m

One Way Bays on One Side One Way Bays on Two Side

Aisle (Access) Aisle (Access)6 m 6 m

Two Way Bays on One Side Two Way Bays on Two Side

Width of AislesParking Angle 300)


Aisle (Access) 3.6 m

One Way Bays on One Side


Two Way Bays on Two Side

300 300


One Way Bays on One Side



300 300


Two Way Bays on One Side



300 300




4.2 m 4.8 m

450 450

Aisle (Access) Aisle (Access)




6.3 m 6.3 m

450 450


4.8 m 4.8 m

600 600






6.6 m 6.6 m

600 600





6.2 m 6.3 m

900 900



7.2 m 7.3 m

900 900


3 m 3 m12 m

7.5 m Entry Exit

Access to ParkingEntry & Exit Together

Regulation 31

Access to ParkingSeparate Entry & Exit

Regulation 31 (4) & Section 2 (9) (a) of 1994 Amendment


Unauthorized Constructions

Without Approval

Violation of Developmen

t Permit

Violations ofSubdivisions

Approvals

Violations ofApproved Building Permit

Not Enough Accessibilit

y

Change of Use

Without Turning Circle or Encroach

Without Splaying

Street Corners

Encroachment of Building

Line

Encroachment of Open Spaces

around the Building

Openings the Blind

Wall

Violation of Light &

Ventilation

Exceed Height of Building

Subdivisions without

Approval

Constructions of Building without

Approval

Occupation of Building or Use of Subdivision without COC

Rear Space Violation

Building Line Violation

Corner Splaying Violation

Ramp Violation

Pedestrian Disturbance

No Disable Ramp

International Disable Accessibility

Road Frontage Violation

Constructions Under High Tension Line

Eco Friendly Telecommunication Tower


UDA Building and Planning Regulations

Documents

Transcript of UDA Building and Planning Regulations