TypicalInstallations - TAPER- · PDF filetypicalinstallations ... on center typical crl weld...
1
Aluminium Base Shoe for Toughened and Laminated Toughened Glass • Typically used as the base channel for glass balustrade systems or windscreens • Drilled and counter bored, or we will custom drill to your • Custom cladding and end caps For more information call FREE on 00 800 0421 6144 (UK & Europe) | Fax FREE on 00 800 0262 3299 Email: [email protected] | www.taper-loc.co.uk Typical Installations Concrete Substrate Typical Surface Mount Detail Steel Tube Substrate Typical Surface Mount Detail Steel L-Angle Substrate Typical Surface Mount Detail Concrete Substrate Typical Concrete Inset Detail Concrete Substrate Typical Fascia Mount Detail Steel Tube Substrate Typical Fascia Mount Detail CONCRETE SUBSTRATE TEMPERED GLASS PANELS LINE OF FINISHED CONCRETE CRL BASE SHOE WITH CLADDING CRL BSG100 ROLL IN VINYL CRL DRY GLAZED TAPERLOC SYSTEM CRL EBA334 HILTI HSL3 CONCRETE ANCHOR INSTALLED 304.8mm ON CENTER TYPICAL 95.25mm MIN EDGE DISTANCE CONCRETE SLAB 4000 PSI MIN 106.4mm 82.6mm CONCRETE SUBSTRATE TEMPERED GLASS PANELS CRL BSG100 ROLL IN VINYL CRL BASE SHOE WITH CLADDING CRL DRY GLAZED TAPERLOC SYSTEM LINE OF FINISHED CONCRETE CONCRETE SLAB 4000 PSI MIN CRL EBA334 HILTI HSL3 CONCRETE ANCHOR INSTALLED 304.8mm ON CENTER TYPICAL 95.25mm MIN EDGE DISTANCE 107.9mm 65mm 95.25mm TEMPERED GLASS PANELS CRL BSG100 ROLL IN VINYL CRL BASE SHOE WITH CLADDING CRL DRY GLAZED TAPERLOC SYSTEM STEEL C-CHANNEL SUBSTRATE CRL SOCKET HEAD CAP SCREW 12.7-330.2 X 38.1mm LONG INSTALLED 304.8mm ON CENTER TYPICAL STEEL STRINGER C-CHANNEL ATTACHMENT 107.95mm 65.1mm LINE OF FINISH FLOOR TEMPERED GLASS PANELS CRL BSG100 ROLL IN VINYL CRL DRY GLAZED TAPERLOC SYSTEM 4.8mm FILLET WELD CRL SOCKET HEAD CAP SCREW 12.7-330.2 X 38.1mm LONG INSTALLED 304.8mm ON CENTER TYPICAL CRL WELD BLOCK INSTALLED 304.8mm ON CENTER TYPICAL STEEL L-ANGLE LINE OF FINISHED CONCRETE TEMPERED GLASS PANELS 4000 PSI CONC MIN CRL BSG100 ROLL IN VINYL CRL DRY GLAZED TAPERLOC SYSTEM CRL TAPERED PROFILE BASE SHOE FOR EMBED/RECESSED APPLICATIONS STEEL MOUNTING/ FORMING PLATE STEEL TUBE SUBSTRATE TEMPERED GLASS PANELS CRL BASE SHOE WITH CLADDING CRL BSG100 ROLL IN VINYL CRL DRY GLAZED TAPERLOC SYSTEM STEEL STRINGER ATTACHMENT CRL WELD BLOCK INSTALLED 304.8mm ON CENTER TYPICAL CRL SOCKET HEAD CAP SCREW 12.7-330.2 X 38.1mm LONG INSTALLED 304.8mm ON CENTER TYPICAL 4.8mm FILLET WELD 119.1mm INSTALLATION GUIDELINE: Anchor spacing will depend on mounting substrate and region of project. INSTALLATION GUIDELINE: During the installation process, two sides of the weld block. INSTALLATION GUIDELINE: During the installation process, two sides of the weld block. INSTALLATION GUIDELINE: When attaching directly to steel, make sure the steel thickness is 9.5mm thick min. If not use CRL’s thick weld blocks.
Transcript of TypicalInstallations - TAPER- · PDF filetypicalinstallations ... on center typical crl weld...
Aluminium Base Shoe for Toughened and Laminated Toughened Glass
• Typically used as the base channel for glass balustrade systems or windscreens
• Drilled and counter bored, or we will custom drill to your
• Custom cladding and end caps
For more information call FREE on 00 800 0421 6144 (UK & Europe) | Fax FREE on 00 800 0262 3299 Email: [email protected] | www.taper-loc.co.uk
Typical Installations
Concrete Substrate Typical Surface Mount Detail
Steel Tube Substrate Typical Surface Mount Detail
Steel L-Angle Substrate Typical Surface Mount Detail Concrete Substrate Typical Concrete Inset Detail
Concrete Substrate Typical Fascia Mount Detail
Steel Tube Substrate Typical Fascia Mount DetailTYPICAL SURFACE MOUNT DETAILCONCRETE SUBSTRATE
TEMPERED GLASSPANELS
LINE OF FINISHED CONCRETE
CRL BASE SHOE WITHCLADDING
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
CRL EBA334 HILTI HSL3CONCRETE ANCHOR INSTALLED304.8mm ON CENTER TYPICAL95.25mm MIN EDGE DISTANCE
ANCHOR SPACING WILL DEPEND ON MOUNTINGSUBSTRATE AND REGION OF PROJECT
CONCRETE SLAB4000 PSI MIN
TYPICAL FACISA MOUNT DETAILCONCRETE SUBSTRATE
ANCHOR SPACING WILL DEPEND ON MOUNTINGSUBSTRATE AND REGION OF PROJECT
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL BASE SHOE WITHCLADDING
CRL DRY GLAZEDTAPERLOC SYSTEM
LINE OF FINISHED CONCRETE
CONCRETE SLAB4000 PSI MIN
CRL EBA334 HILTI HSL3CONCRETE ANCHOR INSTALLED304.8mm ON CENTER TYPICAL95.25mm MIN EDGE DISTANCE
TYPICAL SURFACE MOUNT DETAILSTEEL TUBE SUBSTRATE
STEEL STRINGER ATTACHMENT
4.8mm FILLET WELD
12" ON CENTER ANCHOR SPACING TYPICA
106.
4mm
107.
9mm
65mm
95.2
5mm
82.6
mm
TYPICAL SURFACE MOUNT DETAILCONCRETE SUBSTRATE
TEMPERED GLASSPANELS
LINE OF FINISHED CONCRETE
CRL BASE SHOE WITHCLADDING
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
CRL EBA334 HILTI HSL3CONCRETE ANCHOR INSTALLED304.8mm ON CENTER TYPICAL95.25mm MIN EDGE DISTANCE
ANCHOR SPACING WILL DEPEND ON MOUNTINGSUBSTRATE AND REGION OF PROJECT
CONCRETE SLAB4000 PSI MIN
TYPICAL FACISA MOUNT DETAILCONCRETE SUBSTRATE
ANCHOR SPACING WILL DEPEND ON MOUNTINGSUBSTRATE AND REGION OF PROJECT
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL BASE SHOE WITHCLADDING
CRL DRY GLAZEDTAPERLOC SYSTEM
LINE OF FINISHED CONCRETE
CONCRETE SLAB4000 PSI MIN
CRL EBA334 HILTI HSL3CONCRETE ANCHOR INSTALLED304.8mm ON CENTER TYPICAL95.25mm MIN EDGE DISTANCE
TYPICAL SURFACE MOUNT DETAILSTEEL TUBE SUBSTRATE
STEEL STRINGER ATTACHMENT
4.8mm FILLET WELD
12" ON CENTER ANCHOR SPACING TYPICA
106.
4mm
107.
9mm
65mm
95.2
5mm
82.6
mm
TYPICAL SURFACE MOUNT DETAILCONCRETE SUBSTRATE
TEMPERED GLASSPANELS
LINE OF FINISHED CONCRETE
CRL BASE SHOE WITHCLADDING
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
CRL EBA334 HILTI HSL3CONCRETE ANCHOR INSTALLED304.8mm ON CENTER TYPICAL95.25mm MIN EDGE DISTANCE
ANCHOR SPACING WILL DEPEND ON MOUNTINGSUBSTRATE AND REGION OF PROJECT
CONCRETE SLAB4000 PSI MIN
TYPICAL FACISA MOUNT DETAILCONCRETE SUBSTRATE
ANCHOR SPACING WILL DEPEND ON MOUNTINGSUBSTRATE AND REGION OF PROJECT
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL BASE SHOE WITHCLADDING
CRL DRY GLAZEDTAPERLOC SYSTEM
LINE OF FINISHED CONCRETE
CONCRETE SLAB4000 PSI MIN
CRL EBA334 HILTI HSL3CONCRETE ANCHOR INSTALLED304.8mm ON CENTER TYPICAL95.25mm MIN EDGE DISTANCE
TYPICAL SURFACE MOUNT DETAILSTEEL TUBE SUBSTRATE
TEMPERED GLASSPANELS
CRL BASE SHOE WITHCLADDING
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
STEEL STRINGER ATTACHMENT
CRL WELD BLOCK INSTALLED304.8mm ON CENTER TYPICAL
INSTALLATION GUIDELINE:DURING THE INSTALLATION PROCESSMAKE SURE A CERTIFIED WELDER APPLIESA 4.8mm CONTINUOUS FILLET WELD ONTWO SIDES OF THE WELD BLOCK
CRL SOCKET HEAD CAPSCREW 12.7-330.2 X 38.1mmLONG INSTALLED 304.8mm ONCENTER TYPICAL
4.8mm FILLET WELD
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL BASE SHOE WITHCLADDING
CRL DRY GLAZEDTAPERLOC SYSTEM
TYPICAL SURFACE MOUNT DETAILSTEEL C-CHANNEL SUBSTRATE
CRL SOCKET HEAD CAPSCREW 12.7-330.2 X 38.1mmLONG INSTALLED 304.8mmON CENTER TYPICAL
STEEL STRINGER C-CHANNELATTACHMENT
12" ON CENTER ANCHOR SPACING TYPICAL 12" ON CENTER ANCHOR SPACING TYPICAL
TYPICAL FASCIA MOUNT DETAILSTEEL L-LANGLE SUBSTRATE
LINE OF FINISHFLOOR
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
4.8mm FILLET WELD
CRL SOCKET HEAD CAPSCREW 12.7-330.2 X 38.1mm
LONG INSTALLED 304.8mmON CENTER TYPICAL
CRL WELD BLOCK INSTALLED304.8mm ON CENTER TYPICAL
INSTALLATION GUIDELINE:DURING THE INSTALLATION PROCESSMAKE SURE A CERTIFIED WELDER APPLIESA 4.8mm CONTINUOUS FILLET WELD ONTWO SIDES OF THE WELD BLOCK
STEEL L-ANGLE
12" ON CENTER ANCHOR SPACING TYPICAL TO STEEL ANGLE
106.
4mm
107.
9mm
119.
1mm
107.
95m
m
65.1mm
65mm
95.2
5mm
82.6
mm
TYPICAL SURFACE MOUNT DETAILCONCRETE SUBSTRATE
TEMPERED GLASSPANELS
LINE OF FINISHED CONCRETE
CRL BASE SHOE WITHCLADDING
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
CRL EBA334 HILTI HSL3CONCRETE ANCHOR INSTALLED304.8mm ON CENTER TYPICAL95.25mm MIN EDGE DISTANCE
ANCHOR SPACING WILL DEPEND ON MOUNTING
CONCRETE SLAB4000 PSI MIN
TYPICAL FACISA MOUNT DETAILCONCRETE SUBSTRATE
ANCHOR SPACING WILL DEPEND ON MOUNTINGSUBSTRATE AND REGION OF PROJECT
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL BASE SHOE WITHCLADDING
CRL DRY GLAZEDTAPERLOC SYSTEM
LINE OF FINISHED CONCRETE
CONCRETE SLAB4000 PSI MIN
CRL EBA334 HILTI HSL3CONCRETE ANCHOR INSTALLED304.8mm ON CENTER TYPICAL95.25mm MIN EDGE DISTANCE
TYPICAL SURFACE MOUNT DETAILSTEEL TUBE SUBSTRATE
TEMPERED GLASSPANELS
CRL BASE SHOE WITHCLADDING
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
STEEL STRINGER ATTACHMENT
CRL WELD BLOCK INSTALLED304.8mm ON CENTER TYPICAL
INSTALLATION GUIDELINE:DURING THE INSTALLATION PROCESSMAKE SURE A CERTIFIED WELDER APPLIESA 4.8mm CONTINUOUS FILLET WELD ONTWO SIDES OF THE WELD BLOCK
CRL SOCKET HEAD CAPSCREW 12.7-330.2 X 38.1mmLONG INSTALLED 304.8mm ONCENTER TYPICAL
4.8mm FILLET WELD
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL BASE SHOE WITHCLADDING
CRL DRY GLAZEDTAPERLOC SYSTEM
TYPICAL SURFACE MOUNT DETAILSTEEL C-CHANNEL SUBSTRATE
CRL SOCKET HEAD CAPSCREW 12.7-330.2 X 38.1mmLONG INSTALLED 304.8mmON CENTER TYPICAL
STEEL STRINGER C-CHANNELATTACHMENT
12" ON CENTER ANCHOR SPACING TYPICAL 12" ON CENTER ANCHOR SPACING TYPICAL
TYPICAL FASCIA MOUNT DETAILSTEEL L-LANGLE SUBSTRATE
LINE OF FINISHFLOOR
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
4.8mm FILLET WELD
CRL SOCKET HEAD CAPSCREW 12.7-330.2 X 38.1mm
LONG INSTALLED 304.8mmON CENTER TYPICAL
CRL WELD BLOCK INSTALLED304.8mm ON CENTER TYPICAL
INSTALLATION GUIDELINE:DURING THE INSTALLATION PROCESSMAKE SURE A CERTIFIED WELDER APPLIESA 4.8mm CONTINUOUS FILLET WELD ONTWO SIDES OF THE WELD BLOCK
STEEL L-ANGLE
12" ON CENTER ANCHOR SPACING TYPICAL TO STEEL ANGLE
106.
4mm
107.
9mm
119.
1mm
107.
95m
m
65.1mm
65mm
95.2
5mm
CONCRETE SUBSTRATETYPICAL CONCRETE INSET DETAIL
ANCHOR SPACING WILL DEPEND ON MOUNTINGSUBSTRATE AND REGION OF PROJECT
LINE OF FINISHED CONCRETE
TEMPERED GLASSPANELS
4000 PSICONC MIN
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
CRL TAPERED PROFILEBASE SHOE FOR EMBED/RECESSEDAPPLICATIONS
STEEL MOUNTING/ FORMINGPLATE
TYPICAL SURFACE MOUNT DETAILCONCRETE SUBSTRATE
TEMPERED GLASSPANELS
LINE OF FINISHED CONCRETE
CRL BASE SHOE WITHCLADDING
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
CRL EBA334 HILTI HSL3CONCRETE ANCHOR INSTALLED304.8mm ON CENTER TYPICAL95.25mm MIN EDGE DISTANCE
ANCHOR SPACING WILL DEPEND ON MOUNTINGSUBSTRATE AND REGION OF PROJECT
CONCRETE SLAB4000 PSI MIN
TYPICAL FACISA MOUNT DETAILCONCRETE SUBSTRATE
ANCHOR SPACING WILL DEPEND ON MOUNTINGSUBSTRATE AND REGION OF PROJECT
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL BASE SHOE WITHCLADDING
CRL DRY GLAZEDTAPERLOC SYSTEM
LINE OF FINISHED CONCRETE
CONCRETE SLAB4000 PSI MIN
CRL EBA334 HILTI HSL3CONCRETE ANCHOR INSTALLED304.8mm ON CENTER TYPICAL95.25mm MIN EDGE DISTANCE
TYPICAL SURFACE MOUNT DETAILSTEEL TUBE SUBSTRATE
TEMPERED GLASSPANELS
CRL BASE SHOE WITHCLADDING
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
STEEL STRINGER ATTACHMENT
CRL WELD BLOCK INSTALLED304.8mm ON CENTER TYPICAL
INSTALLATION GUIDELINE:DURING THE INSTALLATION PROCESSMAKE SURE A CERTIFIED WELDER APPLIESA 4.8mm CONTINUOUS FILLET WELD ONTWO SIDES OF THE WELD BLOCK
CRL SOCKET HEAD CAPSCREW 12.7-330.2 X 38.1mmLONG INSTALLED 304.8mm ONCENTER TYPICAL
4.8mm FILLET WELD
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL BASE SHOE WITHCLADDING
CRL DRY GLAZEDTAPERLOC SYSTEM
TYPICAL SURFACE MOUNT DETAILSTEEL C-CHANNEL SUBSTRATE
CRL SOCKET HEAD CAPSCREW 12.7-330.2 X 38.1mmLONG INSTALLED 304.8mmON CENTER TYPICAL
STEEL STRINGER C-CHANNELATTACHMENT
12" ON CENTER ANCHOR SPACING TYPICAL 12" ON CENTER ANCHOR SPACING TYPICAL
TYPICAL FASCIA MOUNT DETAILSTEEL L-LANGLE SUBSTRATE
LINE OF FINISHFLOOR
TEMPERED GLASSPANELS
CRL BSG100ROLL IN VINYL
CRL DRY GLAZEDTAPERLOC SYSTEM
4.8mm FILLET WELD
CRL SOCKET HEAD CAPSCREW 12.7-330.2 X 38.1mm
LONG INSTALLED 304.8mmON CENTER TYPICAL
CRL WELD BLOCK INSTALLED304.8mm ON CENTER TYPICAL
INSTALLATION GUIDELINE:DURING THE INSTALLATION PROCESSMAKE SURE A CERTIFIED WELDER APPLIESA 4.8mm CONTINUOUS FILLET WELD ONTWO SIDES OF THE WELD BLOCK
STEEL L-ANGLE
12" ON CENTER ANCHOR SPACING TYPICAL TO STEEL ANGLE
106.
4mm
107.
9mm
119.
1mm
107.
95m
m
65.1mm
65mm
95.2
5mm
82.6
mm
INSTALLATION GUIDELINE:Anchor spacing will depend on mounting substrate and region of project.
INSTALLATION GUIDELINE:During the installation process,
two sides of the weld block.
INSTALLATION GUIDELINE:During the installation process,
two sides of the weld block.
INSTALLATION GUIDELINE:When attaching directly to steel, make sure the steel thickness is 9.5mm thick min. If not use CRL’s thick weld blocks.
