TABLE OF CONTENT lugs.pdf · 4) Long Barrel Tinned Copper Cable Terminal Ends 5) Tubular...

www.superimpex.com, www.aceelectricals.com

305, Adhyaru Industrial Estate. Sun Mill Compound, Lower Parel (W), Mumbai – 400 013. INDIA

Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933

Email: [email protected]

TABLE OF CONTENT

1) Crimping Type Copper Tubular Cable Terminal Ends - Heavy Duty

2) Crimping Type Copper Tubular Cable Terminal Ends - Light Duty

3) Crimping Type Copper Tubular Cable Terminal Ends - Bell Mouth

4) Long Barrel Tinned Copper Cable Terminal Ends

5) Tubular Compression Cable Lugs

6) Tinned Copper Tubular Cable Lugs Without Inspection Hole N Series

7) Transformer Copper Terminal Ends

8) High Voltage Copper Terminals-33KV

9) 2 Hole Extended Palm Lugs With Inspection Hole

10) Copper Crimp Lug - Australian Standard

11) Tinned Copper Cable Lugs - Spanish Standard

12) Circuit Breaker Lug

13) Copper Standard Wall Starter Terminal Ends

14) Colour Coated Lugs

15) Solid Copper Forging Lugs

16) Weak back Ferrules

17) Long Barrel Connectors

18) Short Barrel Connectors

19) Copper In-Line Connectors

20) Australian Standard Connector

21) Non Tension Connector Upto 33KV

22) Full Tension Connector Upto 33KV

23) Copper Connector With Solid Barrier

24) Tinned Screw Sleeve

25) Copper Tinned Copper 'C' Type Connector

26) T - Connectors

27) Cross - Connectors

28) Copper Reducer Pin Type Terminal Ends

29) Bolted Aluminium Lug

30) Bolted BiMetal Lugs

31) Aluminium Forging Lugs

32) Aluminium Lugs

33) Aluminium 3 Core Sector Cable Lugs

34) Aluminium 3 Core Sector Ferrules

35) Bolted Aluminium Connector

36) Aluminium Through Connectors

37) Aluminium Splice For LV & MV (UP TO 30KV) For Similar Cable Cross Sectional

Areas

38) Aluminium Splice For LV & MV (UP TO 30 KV) For Dissimilar Cable Cross

Sectional Areas

39) Aluminium - Copper BI-Metal Terminals

40) Pre-Insulated Bimetal Lug

41) Special Bimetallic Lugs

42) Bimetallic Lugs With Center Palm



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


43) Bimetallic Lugs With Extended Palm

44) Aluminum Lugs with Copper Ring

45) Bi - Metallic Connector

46) Aluminium - Copper BI - Metal Connector / Splice

47) Mechanical Copper Cable - Lugs Bolted With 2 Screws & 4 Screws

48) Split Bolt Connectors

49) Split Bolt Connectors - Round

50) Copper Solderless Lugs (SLU & SAU Type)

51) PG Clamps AL & Bimetallic

52) Other Range Of Connectors

53) Aluminium Double Barrel Connector

54) Aluminium Single Barrel Connector, One Hole Mount

55) Aluminium Double Barrel Connector One Hole Mount

56) Pre-Insulated Sleeve

57) Tinned Copper Flexible Braids - Crimped With Connectors / Terminals

58) Cable Terminal Ends - (Insulated & Non Insulated)

59) Snap On Terminals

60) Cord End Ferrules

61) ACEPRESS Crimping Tools



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


COPPER LUGS CRIMPING TYPE COPPER TUBULAR CABLE TERMINAL ENDS - HEAVY DUTY MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - WITH INSPECTION HOLE AND BARREL ENDS ARE CHAMPHERED FOR EASY ENTRY.

Cable Size SQ.

mm

Stud Hole E

A C D G H B J Product Code

1.5 4.2 1.8 3.7 8 4 5 5 16 AT 1.5 - 4

5.2 1.8 3.7 8 4 5 5 16 AT 1.5 - 5

6.5 1.8 3.7 10 5 6 5 18 AT 1.5 - 6

2.5 4.2 2.4 4 8 4 5 7 18 AT 2.5 - 4

5.2 2.4 4 10 5 6 7 20 AT 2.5 - 5

6.5 2.4 4 10 5 6 7 20 AT 2.5 - 6

8.4 2.4 4 9 7 8 7 24 AT 2.5-8

4 4.2 3.1 4.8 10 5 6 7 20 AT 4 - 4

5.2 3.1 4.8 10 5 6 7 20 AT 4 - 5

6.5 3.1 4.8 10 5 6 7 20 AT 4 - 6

8.2 3.1 4.8 12 7 8 7 24 AT 4-8

6 5.2 3.8 5.5 10 5 6 9 23 AT 6 - 5

6.5 3.8 5.5 10 5 6 9 23 AT 6 - 6

8.2 3.8 5.5 12 6 9 9 27 AT 6 - 8

10.5 3.8 5.5 15 9 11 9 32 AT 6-10

10 6.5 4.5 6.2 12 6 7 9 25 AT 10 - 6

8.2 4.5 6.2 12 6 7 9 27 AT 10 - 8

10.5 4.5 6.2 15 8.5 10.5 10 32 AT 10 - 10

16 6.5 5.4 7.1 12 7 7 12 30 AT 16 - 6

8.2 5.4 7.1 12 7 9 12 32 AT 16 - 8

10.5 5.4 7.1 15 8 12 12 36 AT 16 - 10

12.7 5.4 7.1 16 8 12 12 36 AT 16 - 12

20 8.4 6 7.7 12 7 9 12 32 AT 20 - 8

25 6.5 6.8 8.8 13 6 7 14 30 AT 25 - 6

8.2 6.8 8.8 13 6 7 14 30 AT 25 - 8

10.5 6.8 8.8 16 9 11 14 37 AT 25 - 10

12.7 6.8 8.8 18 11 13 14 41 AT 25 - 12

35 6.5 8.2 10.6 15 9 9 14 35 AT 35 - 6

8.2 8.2 10.6 15 9 9 14 35 AT 35 - 8

10.5 8.2 10.6 15 9 9 14 35 AT 35 - 10

12.7 8.2 10.6 18 12 13 15 45 AT 35 - 12

17 8.2 10.6 22 12 18 15 52 AT 35-16

50 6.5 9.5 12.4 18 10 11 19 43 AT 50 - 6

8.2 9.5 12.4 18 10 11 19 43 AT 50 - 8

10.5 9.5 12.4 18 10 11 19 43 AT 50 - 10

12.7 9.5 12.4 18 10 11 19 43 AT 50 - 12

16 9.5 12.4 20 12 13 16 47 AT 50-16

70 8.2 11.2 14.7 21 12 13 21 50 AT 70 - 8

10.5 11.2 14.7 21 12 13 21 50 AT 70 - 10

12.7 11.2 14.7 21 12 13 21 50 AT 70 - 12

14.7 11.2 14.7 28 16 16 18 57 AT 70-14

17 11.2 14.7 28 16 16 18 57 AT 70-16

95 8.4 13.5 17.4 25 13 13 23 55 AT 95 - 8

10.5 13.5 17.4 25 13 13 23 55 AT 95 - 10

12.7 13.5 17.4 25 13 13 23 55 AT 95 - 12

14.7 13.5 17.4 25 13 13 23 55 AT 95 - 14



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


17 13.5 17.4 28 16 16 20 61 AT 95-16

120 8.2 15 19.4 28 14 14 25 60 AT 120 - 8

10.5 15 19.4 28 14 14 25 60 AT 120 - 10

12.7 15 19.4 28 14 14 25 60 AT 120 - 12

14.7 15 19.4 28 16 16 22 64 AT 120-14

17 15 19.4 28 14 14 25 60 AT 120 - 16

150 8.4 16.5 21.2 30 16 16 30 69 AT 150 - 8

10.5 16.5 21.2 30 16 16 30 69 AT 150 - 10

12.7 16.5 21.2 30 16 16 30 69 AT 150 - 12

14.7 16.5 21.2 30 16 16 30 69 AT 150 - 14

17 16.5 21.2 30 16 16 30 69 AT 150 - 16

21 16.5 21.2 34 19 23 26 79 AT 150-20

185 10.5 18.5 23.5 34 17 17 36 78 AT 185 - 10

13 18.5 23.5 34 17 17 36 78 AT 185 - 12

14.7 18.5 23.5 34 17 17 36 78 AT 185 - 14

17 18.5 23.5 34 17 17 36 78 AT 185 - 16

21 18.5 23.5 34 17 17 32 78 AT 185-20

240 10.5 21 26.5 38 20 20 42 92 AT 240 - 10

13 21 26.5 38 20 20 42 92 AT 240 - 12

14.7 21 26.5 38 20 20 42 92 AT 240 - 14

17 21 26.5 38 20 20 42 92 AT 240 - 16

21 21 26.5 38 20 20 42 92 AT 240 - 20

- 21 26.5 38 - - 38 92 AT 240-BL

300 13 23.5 30 43 22 22 46 101 AT 300 - 12

14.7 23.5 30 43 22 22 46 101 AT 300 - 14

17 23.5 30 43 22 22 46 101 AT 300 - 16

21 23.5 30 43 22 22 46 101 AT 300 - 20

- 23.5 30 43 - - 42 101 AT 300-BL

400 13 28.5 36.5 50 26 26 44 114 AT400-12

14.7 28.5 36.5 50 26 26 49 114 AT 400 - 14

17 28.5 36.5 50 26 26 49 114 AT 400 - 16

21 28.5 36.5 50 26 26 49 114 AT 400 - 20

- 28.5 36.5 50.1 - - 44 114 AT 400-BL

500 14.7 30 39 56 28 28 53 124 AT 500 - 14

17 30 39 56 28 28 53 124 AT 500 - 16

21 30 39 56 28 28 53 124 AT 500 - 20

- 30 39 56 - - 48 124 AT 500-BL

630 17 35 45 65 33 33 61 144 AT 630 - 16

21 35 45 65 33 33 61 144 AT 630 - 20

- 35 45 65 - - 56 144 AT 630-BL

800 BL 39 50.6 73 35 40 78 170 AT 800 - BL

17 39 50.6 73 35 40 78 170 AT 800 - 16

21 39 50.6 73 35 40 78 170 AT 800 - 20

1000 BL 43 56.2 81 45 45 90 200 AT 1000 - BL

17 43 56.2 81 45 45 90 200 AT 1000 - 16

21 43 56.2 81 45 45 90 200 AT 1000 - 20



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


CRIMPING TYPE COPPER TUBULAR CABLE TERMINAL ENDS - LIGHT DUTY MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - WITH INSPECTION HOLE AND BARREL ENDS ARE CHAMPHERED FOR EASY ENTRY.

Cable Size SQ.

mm

Stud Hole E

A C D G H B J Product Code

1.5 4.2 1.8 3.7 8 4 5 5 16 ALD 1.5 - 4

5.2 1.8 3.7 8 4 5 5 16 ALD 1.5 - 5

6.5 1.8 3.7 10 5 6 5 18 ALD 1.5 - 6

2.5 4.2 2.4 4 8 4 5 7 18 ALD 2.5 - 4

5.2 2.4 4 10 5 6 7 20 ALD 2.5 - 5

6.5 2.4 4 10 5 6 7 20 ALD 2.5 - 6

8.4 2.4 4 9 7 8 7 24 ALD 2.5-8

4 4.2 3.1 4.8 10 5 6 7 20 ALD 4 - 4

5.2 3.1 4.8 10 5 6 7 20 ALD 4 - 5

6.5 3.1 4.8 10 5 6 7 20 ALD 4 - 6

8.2 3.1 4.8 12 7 8 7 24 ALD 4-8

6 5.2 3.8 5.5 10 5 6 9 23 ALD 6 - 5

6.5 3.8 5.5 10 5 6 9 23 ALD 6 - 6

8.2 3.8 5.5 12 6 9 9 27 ALD 6 - 8

10.5 3.8 5.5 15 9 11 9 32 ALD 6-10

10 6.5 4.5 6.2 12 6 7 9 25 ALD 10 - 6

8.2 4.2 6.2 12 6 9 9 27 ALD 10 - 8

10.5 4.5 6.2 15 8.5 10.5 10 32 ALD 10 - 10

16 6.5 5.4 7.1 12 7 7 12 30 ALD 16 - 6

8.2 5.4 7.1 12 7 9 12 32 ALD 16 - 8

10.5 5.4 7.1 15 8 12 12 36 ALD 16 - 10

12.7 5.4 7.1 16 8 12 12 36 ALD 16 - 12

20 8.4 6 7.7 12 7 9 12 32 ALD 20 - 8

25 6.5 6.8 8.8 13 6 7 14 30 ALD 25 - 6

8.2 6.8 8.8 13 6 7 14 30 ALD 25 - 8

10.5 6.8 8.8 16 9 11 14 37 ALD 25 - 10

12.7 6.8 8.8 18 11 13 14 41 ALD 25 - 12

35 6.5 8 10 15 9 9 14 35 ALD 35 - 6

8.4 8 10 15 9 9 14 35 ALD 35 - 8

10.5 8 10 15 9 9 14 35 ALD 35 - 10

50 6.5 9.2 11.2 16 10 11 19 43 ALD 50 - 6

8.4 9.2 11.2 16 10 11 19 43 ALD 50 - 8

10.5 9.2 11.2 16 10 11 19 43 ALD 50 - 10

12.7 9.2 11.2 16 10 11 19 43 ALD 50 - 12

70 8.4 11.5 13.8 20 12 13 21 50 ALD 70 - 8

10.5 11.5 13.8 20 12 13 21 50 ALD 70 - 10

12.7 11.5 13.8 20 12 13 21 50 ALD 70 - 12

95 8.4 12.8 15.6 23 13 13 23 55 ALD 95 - 8

10.5 12.8 15.8 23 13 13 23 55 ALD 95 - 10

12.7 12.8 15.6 23 13 13 23 55 ALD 95 - 12

14.7 12.8 15.6 23 13 13 23 55 ALD 95 - 14

120 8.2 14.8 17.8 26 14 14 25 60 ALD 120 - 8

10.5 14.8 17.8 26 14 14 25 60 ALD 120 - 10

12.7 14.8 17.8 26 14 14 25 60 ALD 120 - 12

17 14.8 17.8 26 14 14 25 60 ALD 120 - 17

150 8.4 16 19.6 28 16 16 30 69 ALD 150 - 8

10.5 16 19.6 28 16 16 30 69 ALD 150 - 10

12.7 16 19.6 28 16 16 30 69 ALD 150 - 12

14.7 16 19.6 28 16 16 30 69 ALD 150 - 14



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


17 16 19.6 28 16 16 30 69 ALD 150 - 17

185 10.5 18 22 32 17 17 36 78 ALD 185 - 10

13 18 22 32 17 17 36 78 ALD 185 - 12

14.7 18 22 32 17 17 36 78 ALD 185 - 14

17 18 22 32 17 17 36 78 ALD 185 - 16

240 10.5 22 26 38 20 20 42 92 ALD 240 - 10

13 22 26 38 20 20 42 92 ALD 240 - 12

14.7 22 26 38 20 20 42 92 ALD 240 - 14

17 22 26 38 20 20 42 92 ALD 240 - 16

21 22 26 38 20 20 42 92 ALD 240 - 20

300 13 24 28.7 42 22 22 46 101 ALD 300 - 12

14.7 24 28.7 42 22 22 46 101 ALD 300 - 14

17 24 28.7 42 22 22 46 101 ALD 300 – 16

21 24 28.7 42 22 22 46 101 ALD 300 - 20

400 14.7 28 33.2 49 26 26 49 114 ALD 400 - 14

17 28 33.2 49 26 26 49 114 ALD 400 - 16

21 28 33.2 49 26 26 49 114 ALD 400 – 20

500 14.7 30 36 53 28 28 53 124 ALD 500 - 14

17 30 36 53 28 28 53 124 ALD 500 - 16

21 30 36 53 28 28 53 124 ALD 500 - 20

630 17 35 41.5 61 33 33 61 144 ALD 630 - 16

21 35 41.5 61 33 33 61 144 ALD 630 - 20

CRIMPING TYPE COPPER TUBULAR CABLE TERMINAL ENDS - BELLL MOUTH MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - BELL MOUTH ENTRY, WITH OR WITHOUT INSPECTION HOLE For ordering BELL MOUTHED cable terminals prefix B to the product code nos. of Crimping Type Copper Tubular Cable Terminal ends. For eg. AT 120 - 12 will be BAT 120 – 12.



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


LONG BARREL TINNED COPPER CABLE TERMINAL ENDS MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - WITH INSPECTION HOLE

Cable mm2 Stud Hole E

Dimensions (mm2) Product Code

A C D B L

10 - 6 6.4 4.7 6.9 11.9 19 35 ATL 10 - 6

10 - 8 8.3 4.7 6.9 13.5 19 38 ATL 10 - 8

16 - 6 6.4 5.6 7.8 11.9 23 39 ATL 16 - 6

16 - 8 8.3 5.6 7.8 13.6 23 42 ATL 16 - 8

25 - 8 8.3 7.1 9.5 13.5 29 50 ATL 25 - 8

25 - 10 10.5 7.1 9.5 16 29 53 ATL 25 - 10

35 - 8 8.3 8.2 11 15.7 30 54 ATL 35 - 8

35 - 10 10.5 8.2 11 15.7 30 58 ATL 35 - 10

50 - 10 10.5 9.5 12.5 17.9 35 64 ATL 50 - 10

50 - 12 13 9.5 12.5 17.9 35 64 ATL 50 - 12

70 - 10 10.5 11.5 15 21.5 38 70 ATL 70 - 10

70 - 12 13 11.5 15 21.5 38 70 ATL 70 - 12

95 - 14 14.5 13.5 17 24.7 43 88 ATL 95 - 14

95 - 16 16.5 13.5 17 24.7 43 88 ATL 95 - 16

120 - 14 14.5 15.6 20 28.9 49 94 ATL 120 - 14

120 - 16 16.5 15.6 20 28.9 49 94 ATL 120 - 16

150 - 14 14.5 16.5 21 30.4 56 102 ATL 150 - 14

150 - 16 16.5 16.5 21 30.4 56 102 ATL 150 - 16

185 - 14 14.5 18.4 23.6 37 63 113 ATL 185 14

185 - 16 16.5 18.4 23.6 37 63 113 ATL 185 - 16

240 - 14 14.5 21.2 26.4 41 66 119 ATL 120 - 14

240 - 16 16.5 21.2 26.4 41 66 119 ATL 120 - 16

300 - 14 14.5 23.4 28.6 45.6 77 133 ATL 300 - 14

400 - 16 16.5 26.8 32.8 50 71.7 140 ATL 400 - 16

Other Hole Sizes Available As Per Request.



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


TUBULAR COMPRESSION CABLE LUGS (As Per Din 46235) MATERIAL - E - COPPER FINISH - UNCOATED / ELECTRO TINNED FEATURES - WITHOUT INSPECTION HOLE Circular Stranded Copper Conductor To DIN 48201 & Circular Stranded/Sector Shaped Conductor To DIN VDE 0295.

Sizes Atud. Hole

Inside Outside Width Barrel Length Product Code

E A C D B J

6 - 5 5.3 3.8 5.5 8.5 10.0 30.5 AUTD 6 - 5

6 - 6 6.4 3.8 5.5 8.5 10.0 31.5 AUTD 6 - 6

6 - 8 8.4 3.8 5.5 10.0 10.0 34.0 AUTD 6 - 8

10 - 5 5.3 4.5 6.0 9.0 10.0 34.0 AUTD 10 - 5

10 - 6 6.4 4.5 6.0 9.0 10.0 34.5 AUTD 10 - 6

10 - 8 8.4 4.5 6.0 13.0 10.0 37.0 AUTD 10 - 8

16 - 6 6.4 5.5 8.5 13.0 20.0 43.5 AUTD 16 - 6

16 - 8 8.4 5.5 8.5 13.0 20.0 46.0 AUTD 16 - 8

16 - 10 10.5 5.5 8.5 17.0 20.0 48.0 AUTD 16 - 10

16 - 12 13.0 5.5 8.5 18.0 20.0 49.0 AUTD 16 - 12

25 - 6 6.4 7.0 10.0 14.0 20.0 45.5 AUTD 25 - 6

25 - 8 8.4 7.0 10.0 16.0 20.0 48.0 AUTD 25 - 8

25 - 10 10.5 7.0 10.0 17.0 20.0 50.0 AUTD 25 - 10

25 - 12 13.0 7.0 10.0 19.0 20.0 51.0 AUTD 25 - 12

35 - 6 6.4 8.2 12.5 17.0 20.0 49.5 AUTD 35 - 6

35 - 8 8.4 8.2 12.5 17.0 20.0 52.0 AUTD 35 - 8

35 - 10 10.5 8.2 12.5 19.0 20.0 54.0 AUTD 35 - 10

35 - 12 13.0 8.2 12.5 21.0 20.0 55.0 AUTD 35 - 12

35 - 14 15.0 8.2 12.5 21.0 20.0 56.5 AUTD 35 - 14

50 - 8 8.4 10.0 14.5 20.0 28.0 62.0 AUTD 50 - 8

50 - 10 10.5 10.0 14.5 22.0 28.0 64.0 AUTD 50 - 10

50 - 12 13.0 10.0 14.5 24.0 28.0 65.0 AUTD 50 - 12

50 - 14 15.0 10.0 14.5 24.0 28.0 66.5 AUTD 50 - 14

50 - 16 17.0 10.0 14.5 28.0 28.0 68.0 AUTD 50 - 16

70 - 8 8.4 11.5 16.5 24.0 28.0 65.0 AUTD 70 - 8

70 - 10 10.5 11.5 16.5 24.0 28.0 67.0 AUTD 70 - 10

70 - 12 13.0 11.5 16.5 24.0 28.0 68.0 AUTD 70 - 12

70 - 14 15.0 11.5 16.5 24.0 28.0 69.5 AUTD 70 - 14

70 - 16 17.0 11.5 16.5 30.0 28.0 71.0 AUTD 70 - 16

95 - 8 8.4 13.5 19.0 28.0 35.0 77.0 AUTD 95 - 8

95 - 10 10.5 13.5 19.0 28.0 35.0 77.0 AUTD 95 - 10

95 - 12 13.0 13.5 19.0 28.0 35.0 78.0 AUTD 95 - 12

95 - 14 15.0 13.5 19.0 28.0 35.0 79.5 AUTD 95 - 14

95 - 16 17.0 13.5 19.0 32.0 35.0 81.0 AUTD 95 - 16

120 - 10 10.5 15.5 21.0 32.0 35.0 85.0 AUTD 120 - 10

120 - 12 13.0 15.5 21.0 32.0 35.0 86.0 AUTD 120 - 12

120 - 14 15.0 15.5 21.0 32.0 35.0 88.0 AUTD 120 - 14

120 - 16 17.0 15.5 21.0 32.0 35.0 89.0 AUTD 120 - 16

120 - 20 21.0 15.5 21.0 38.0 35.0 91.0 AUTD 120 - 20

150 - 10 10.5 17.0 23.5 34.0 35.0 93.0 AUTD 150 - 10

150 - 12 13.0 17.0 23.5 34.0 35.0 94.0 AUTD 150 - 12

150 - 14 15.0 17.0 23.5 34.0 35.0 97.0 AUTD 150 - 14

150 - 16 17.0 17.0 23.5 34.0 35.0 97.0 AUTD 150 - 16

150 - 20 21.0 17.0 23.5 40.0 35.0 99.0 AUTD 150 - 20

185 - 10 10.5 19.0 25.5 37.0 40.0 97.0 AUTD 185 - 10

185 - 12 13.0 19.0 25.5 37.0 40.0 98.0 AUTD 185 - 12

185 - 14 15.0 19.0 25.5 37.0 40.0 101.0 AUTD 185 - 14

185 - 16 17.0 19.0 25.5 37.0 40.0 101.0 AUTD 185 - 16

185 - 20 21.0 19.0 25.5 40.0 40.0 103.0 AUTD 185 - 20

240 - 12 13.0 21.5 29.0 42.0 40.0 108.0 AUTD 240 - 12

240 - 14 15.0 21.5 29.0 42.0 40.0 111.0 AUTD 240 - 14



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


240 - 16 17.0 21.5 29.0 42.0 40.0 111.0 AUTD 240 - 16

240 - 20 21.0 21.5 29.0 45.0 40.0 113.0 AUTD 240 - 20

300 - 12 13.0 24.5 32.0 48.0 50.0 119.0 AUTD 300 - 12

300 - 14 15.0 24.5 32.0 48.0 50.0 119.0 AUTD 300 - 14

300 - 16 17.0 24.5 32.0 48.0 50.0 119.0 AUTD 300 - 16

300 - 20 21.0 24.5 32.0 48.0 50.0 122.0 AUTD 300 - 20

400 - 14 15.0 27.5 38.5 55.0 70.0 140.0 AUTD 400 - 14

400 - 16 17.0 27.5 38.5 55.0 70.0 140.0 AUTD 400 - 16

400 - 20 21.0 27.5 38.5 55.0 70.0 140.0 AUTD 400 - 20

500 - 16 17.0 31.0 42.0 60.0 70.0 150.0 AUTD 500 - 16

500 - 20 21.0 31.0 42.0 60.0 70.0 150.0 AUTD 500 - 20

625 - 16 17.0 34.5 44.0 64.0 80.0 160.0 AUTD 625 - 16

625 - 20 21.0 34.5 44.0 64.0 80.0 160.0 AUTD 625 - 20

800 - 16 17.0 40.0 52.0 75.0 100.0 195.0 AUTD 800 - 16

800 - 20 21.0 40.0 52.0 75.0 100.0 195.0 AUTD 800 - 20

1000 - 16 17.0 44.0 58.0 85.0 100.0 195.0 AUTD 1000 - 16

1000 - 20 21.0 44.0 58.0 85.0 100.0 195.0 AUTD 1000 - 20



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


TINNED COPPER TUBULAR CABLE LUGS WITHOUT INSPECTION HOLE N SERIES MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - WITH OR WITHOUT INSPECTION HOLE

Cable mm2

Stud Hole E

Dimensions in mm Product Code

A C D B K G H J

2.5 5.3 2.4 4 10 8 3 5 6 22 ANL 2.5 - 5

4 5.3 3.1 4.8 10 8 3 5 6 22 ANL 4 - 5

6 5.3 3.8 5.5 10 9 3 5 6 23.5 ANL 6 - 5

6.5 3.8 5.5 10 9 3 6 5 23.5 ANL 6 - 6

8.5 3.8 5.5 12 9 3 7 8 28 ANL 6 - 8

10.5 3.8 6 14.5 9 3 8 14 33 ANL 6 - 10

13 3.8 6 17 9 3 12 13 36 ANL 6 - 12

10 5.3 4.5 6.2 10 10 3 6 7 26 ANL 10 - 5

6.5 4.5 6.2 10.5 10 3 6 7 26.5 ANL 10 - 6

8.5 4.5 6.2 12 10 3 7 9 28 ANL 10 - 8

10.5 4.5 7 15 10 3 8 13 34 ANL 10 - 10

13 4.5 7 17 10 3 12 13 40 ANL 10 - 12

16 5.3 5.4 7.1 10.5 13 4 6.5 7 31 ANL 16 - 5

6.5 5.4 7.1 10.5 13 4 6.5 7 31 ANL 16 - 6

8.5 5.4 7.1 12 13 4 7 9 32 ANL 16 - 8

10.5 5.5 7.6 15 13 4 8 13 38 ANL 16 - 10

13 5.5 7.6 17 13 4 12 13 42 ANL 16 - 12

25 5.3 6.8 8.8 13 13 5 6.5 7 32 ANL 25 - 5

6.5 6.8 8.8 13 13 5 6.5 7 32 ANL 25 - 6

8.5 6.8 8.8 13 13 5 6 9 32 ANL 25 - 8

10.5 6.8 8.8 15 13 5 8 13 38 ANL 25 - 10

13 6.8 9.5 18 13 5 11 14 42 ANL 25 - 12

15 6.8 9.5 21 13 5 13 14 45 ANL 25 - 14

35 6.5 8.2 10.6 15 15 7 7 9 37.5 ANL 35 - 6

8.5 8.2 10.6 15 15 7 9 11 42 ANL 35 - 8

10.5 8.2 10.6 15 16 8 9 15 48 ANL 35 - 10

13 8.2 10.6 17 15 8 14 14 53 ANL 35 - 12

15 8.2 10.6 20 15 8 14 14 53 ANL 35 - 14

50 6.5 9.5 12.4 17.5 17 7 9 11 44 ANL 50 - 6

8.5 9.5 12.4 17.5 17 7 9 11 44 ANL 50 - 8

10.5 9.5 12.4 17.5 17 8 12 12 49 ANL 50 - 10

13 9.5 12.4 20.5 17 8 14.5 14 53 ANL 50 - 12

15 9.5 12.4 23 17 8 14.5 15 54 ANL 50 - 14

70 6.5 11.2 14.7 21 21 7 10 10 48 ANL 70 - 6

8.5 11.2 14.7 21 21 7 10 10 48 ANL 70 - 8

10.5 11.2 14.7 21 21 8 12 12 51.5 ANL 70 - 10

13 11.2 14.7 21 21 8 13 13 55 ANL 70 - 12

15 11.2 14.7 22 21 10 15 17 61 ANL 70 - 14

95 8.5 13.5 17.4 25 23 8 12 12 55 ANL 95 - 8

10.5 13.5 17.4 25 24 8 12 12 55 ANL 95 - 10

13 13.5 17.4 25 24 8 13 13 59 ANL 95 - 12

15 13.5 17.4 25 24 10 15 17 67 ANL 95 - 14

17 13.5 17.4 26 24 10 16 16 67 ANL 95 - 16

21 13.5 17.4 28 24 10 16 17 68 ANL 95 - 20

120 8.5 15 19.4 28 24 - - - 65 ANL 120 - 8

10.5 15 19.4 28 24 - - - 65 ANL 120 - 10



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


13 15 19.4 28 24 - - - 65 ANL 120 - 12

15 15 19.4 28 24 - - - 68 ANL 120 - 14

17 15 19.4 28 24 - - - 68 ANL 120 - 16

21 15 19.4 28 24 - - - 68 ANL 120 - 20

150 8.5 16.5 21.2 30 30 - - - 69 ANL 150 - 8

10.5 16.5 21.2 30 30 - - - 69 ANL 150 - 10

13 16.5 21.2 30 30 - - - 72 ANL 150 - 12

15 16.5 21.2 30 30 - - - 72 ANL 150 - 14

17 16.5 21.2 30 30 - - - 72 ANL 150 - 16

21 16.5 21.2 30 30 - - - 72 ANL 150 - 20

185 10.5 19 23.5 34 30 - - - 82 ANL 185 - 10

13 19 23.5 34 30 - - - 82 ANL 185 - 12

15 19 23.5 34 30 - - - 82 ANL 185 - 14

17 19 23.5 34 30 - - - 82 ANL 185 - 16

21 19 23.5 34 30 - - - 89 ANL 185 - 20

240 10.5 21 26.5 38 35 - - - 94 ANL 240 - 10

13 21 26.5 38 35 - - - 94 ANL 240 - 12

15 21 26.5 38 35 - - - 94 ANL 240 - 14

17 21 26.5 38 35 - - - 94 ANL 240 - 16

300 13 23.5 30 43 46 - - - 111 ANL 300 - 12

15 23.5 30 43 46 - - - 111 ANL 300 - 14

17 23.5 30 43 46 - - - 111 ANL 300 - 16

21 23.5 30 43 46 - - - 111 ANL 300 - 20

400 17 27 36.5 50 49 - - - 114 ANL 400 - 16

21 27 36.5 50 49 - - - 114 ANL 400 - 20

500 17 30 39 56 58 - - - 134 ANL 500 - 16

21 30 39 56 58 - - - 134 ANL 500 - 20

630 17 35 41.5 61 70 - - - 144 ANL 630 - 16

21 35 41.5 61 70 - - - 144 ANL 630 - 20

10.5 35 41.5 61 70 - - - 144 ANL 630 - 4 E10

TRANSFORMER COPPER TERMINAL ENDS MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - WITH / WITHOUT INSPECTION HOLE

Cable mm2

Stud Hole E


A C D B L H J

300 8.5 23.5 30 56 42 35 25 101 AT 3004 E - 8

10.5 23.5 30 56 42 35 25 101 AT 3004 E - 10

400 8.5 28.5 36.5 56 44 35 25 114 AT 4004 - E - 8

10.5 28.5 36.5 56 44 35 25 114 AT 4004 E - 10

500 8.5 30 39 56 48 35 25 124 AT 5004 E - 8

10.5 30 39 56s 48 35 25 124 AT 5004 E - 10

*630 8.5 35 45 65 56 35 25 144 AT 6304 E - 8

10.5 35 45 65 56 35 25 144 AT 6304 E - 10



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


* Flat Head on Request

HIGH VOLTAGE COPPER TERMINALS - 33 KV MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - WITHOUT INSPECTION HOLE

These terminals are designed for high voltage applications upto 33kv.

They are manufactured form high purity copper tube, annealed & tin plated.

The extended barrel enhances both electrical and mechanical performance.

The absence of an inspection hole to prevent moisture entry into the crimped joint makes these terminals suitable for outdoor applications.

Cable mm2

Stud Hole E


A C D G H J

25 8 6.8 10.0 14.0 8.0 9.0 65.0 AVCT 25 - 8

10 6.8 10.0 18.0 11.0 13.0 72.0 AVCT 25 - 10

12 6.8 10.0 21.0 14.0 16.0 78.0 AVCT 25 - 12

35 12 8.2 12.5 21.0 14.0 16.0 79.0 AVCT 35 - 12

16 8.2 12.5 26.0 17.0 19.0 85.0 AVCT 35 - 16

50 12 9.5 14.5 21.0 14.0 16.0 79.0 AVCT50 - 12

16 9.5 14.5 26.0 17.0 19.0 85.0 AVCT50 - 16

70 12 11.0 16.0 28.0 14.0 16.0 81.0 AVCT 70 - 12

16 11.0 16.0 30.0 17.0 19.0 87.0 AVCT 70 - 16

95 12 13.5 19.0 28.0 14.0 16.0 91.0 AVCT 95 - 12

14 13.5 19.0 29.0 16.0 18.0 95.0 AVCT 95 - 14

16 13.5 19.0 30.0 17.0 20.0 97.0 AVCT 95 - 16

120 12 15.0 20.5 31.0 14.0 16.0 97.0 AVCT 120 - 12

14 15.0 20.0 31.0 16.0 18.0 101.0 AVCT 120 - 14

150 12 16.5 23.0 32.0 14.0 16.0 97.0 AVCT 150 - 12

14 16.5 23.0 32.0 16.0 18.0 101.0 AVCT 150 - 14

185 14 17.0 23.5 16.0 32.5 18.0 101.0 AVCT 185 - 14

240 14 19.2 25.5 44.0 16.0 18.0 105.0 AVCT 240 - 14

300 14 23.5 32.0 43.0 16.0 18.0 105.0 AVCT 300 - 14

400 14 27.0 38.0 51.0 19.0 22.0 140.0 AVCT 400 - 14

16 27.0 38.0 51.0 19.0 22.0 140.0 AVCT 400 - 16

20 27.0 38.0 51.0 23.0 24.0 146.0 AVCT 400 - 20

500 16 30.3 41.0 56.5 19.0 22.0 147.0 AVCT 500 - 16

20 30.3 41.0 56.5 23.0 24.0 153.0 AVCT 500 - 20

630 16 33.4 43.0 61.5 19.0 22.0 159.0 AVCT 630 - 16

20 33.4 43.0 61.5 23.0 24.0 165.0 AVCT 630 - 20

Note: All dimensions in mm



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


2 HOLE EXTENDED PALM LUGS WITH INSPECTION HOLE MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - WITH / WITHOUT INSPECTION HOLE

Cable mm2 Stud Hole E Dimensions Product Code

A C D B J

16 10.5 5.4 7.6 14.5 16 100 AT162E10

25 10.5 6.8 8.8 15 16 100 AT252E10

35 10.5 8.2 10.6 16.5 16 100 AT352E10

50 10.5 9.5 12.4 17 25 109 AT502E10

13 9.5 12.4 17 25 109 AT502E12

70 10.5 11.3 14.7 21 30 114 AT702E10

13 11.3 14.7 21 30 114 AT702E12

95 10.5 13.5 17.4 25 30 116 AT952E10

13 13.5 17.4 25 30 116 AT952E12

120 10.5 15 19.4 27.5 35 122 AT1202E10

13 15 19.4 27.5 35 122 AT1202E12

150 10.5 16.5 21.2 30 40 126 AT1502E10

13 16.5 21.2 30 40 126 AT1502E12

185 10.5 18.5 23.5 33.5 42 132 AT1852E10

13 18.5 23.5 33.5 42 132 AT1852E12

240 10.5 21 26.5 38.5 50 143 AT2402E10

13 21 26.5 38.5 50 143 AT2402E12

300 13.7 23.5 30 43 55 144 AT3002E12

400 13.7 28.5 36.5 52.5 60 149 AT4002E12

500 13.7 30 39 56 65 160 AT5002E12

630 13.7 35 45 36.8 75 160 AT6302E12

*.Also available in blank palm (without hole)



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


COPPER CRIMP LUG – AUSTRALIAN STANDARD - MATERIAL - E - COPPER FINISH - ELECTRO TINNED

Cable mm2

Stud Hole E

Dimensions Product Code

A D F B G H J

1.5-4 4.2 2 8 1.0 7.5 4 5 18.5 AAU 1.5 - 4

1.5-5 5.2 2 8 1.0 7.5 4 5 18.5 AAU 1.5 - 5

1.5-6 6.5 2 10 0.8 7.5 4 6 19.5 AAU 1.5 - 6

2.5-4 4.2 2.5 8 1.0 8 4 5 19 AAU 2.5 - 4

2.5-5 5.2 2.5 10 0.8 8 5 6 20 AAU 2.5 - 5

2.5-6 6.5 2.5 10 0.8 8 5 6 20 AAU 2.5 - 6

2.5-8 8.4 2.5 11 0.7 8 6 9 26 AAU 2.5 - 8

4-5 5.2 3.3 10 1.0 9 5 6 22 AAU 4 - 5

4-6 6.5 3.3 10 1.0 9 5 6 22 AAU 4 - 6

4-8 8.4 3.3 12 0.8 9 6 9 26 AAU 4 - 8

4-10 10.2 3.3 15 0.8 9 8 11 32 AAU 4 - 10

6-5 5.2 3.8 10 1.2 10 5 6 23 AAU 6 - 5

6-6 6.5 3.8 12 1.0 10 6 9 27 AAU 6 - 6

6-8 8.4 3.8 12 1.0 10 6 9 27 AAU 6 - 8

6-10 10.2 3.8 15 0.8 10 8 11 32 AAU 6 - 10

10-5 5.2 4.7 12 1.8 10 6 7 27 AAU 10 - 5

10-6 6.5 4.7 12 1.8 10 6 7 27 AAU 10 - 6

10-8 8.4 4.7 14 1.6 10 7 8 29 AAU 10 - 8

10-10 10.5 4.7 15 1.5 10 8 10 32 AAU 10 - 10

10-12 13 4.7 18 1.0 10 10 12 38 AAU 10 - 12

16-6 6.5 5.5 11 2.4 19 7 9 39 AAU 16 - 6

16-8 8.4 5.5 14 1.7 19 7 9 39 AAU 16 - 8

16-10 10.5 5.5 16 1.5 19 8 10 41 AAU 16 - 10

16-12 13 5.5 18 1.2 19 10 13 46 AAU 16 - 12

25-6 6.5 7.1 13.5 2.4 21 7 9 41 AAU 25 - 6

25-8 8.4 7.1 13.5 2.4 21 7 9 41 AAU 25 - 8

25-10 10.5 7.1 16 1.9 21 9 10 44 AAU 25 - 10

25-12 13 7.1 18 1.6 21 10 13 48 AAU 25 - 12

35-6 6.5 8.4 16 3.0 21 9 10 45 AAU 35 - 6

35-8 8.4 8.4 16 3.0 21 9 10 45 AAU 35 - 8

35-10 10.5 8.4 18 2.6 21 9 10 45 AAU 35 - 10

35-12 13 8.4 20 2.2 22 11 13 51 AAU 35 - 12

50-6 6.5 9.5 18 3.3 22 8 10 46 AAU 50 - 6

50-8 8.4 9.5 18 3.3 22 8 10 46 AAU 50 - 8

50-10 10.5 9.5 18 3.3 22 8 10 52 AAU 50 - 10

50-12 13 9.5 21 2.7 22 11 13 54 AAU 50 - 12

70-6 6.5 11.3 21 3.5 22 11 13 54 AAU 70 - 6

70-8 8.4 11.3 21 3.5 24 11 13 54 AAU 70 - 8

70-10 10.5 11.3 21 3.5 24 11 13 54 AAU 70 - 10

70-12 13 11.3 21 3.5 24 11 13 54 AAU 70 - 12

70-16 17 11.3 26 3.0 24 14 60 61 AAU 70 - 16

95-8 8.4 13.5 25 4.0 27 12 14 60 AAU 95 - 8

95-10 10.5 13.5 25 4.0 27 12 14 60 AAU 95 - 10

95-12 13 13.5 25 4.0 27 12 14 60 AAU 95 - 12

95-16 17 13.5 25 3.5 27 14 16 61 AAU 95 - 16

120-8 8.4 15.6 30 5.0 30 12 14 64 AAU 120 - 8

120-10 10.5 15.6 30 5.0 30 12 14 64 AAU 120 - 10

120-12 13 15.6 30 5.0 30 12 14 64 AAU 120 - 12

120-16 17 15.6 30 5.0 30 16 16 72 AAU 120 - 16

150-10 10.5 16.7 32 5.8 30 16 16 71 AAU 150 - 10



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


150-12 13 16.7 32 5.8 32 18 18 75 AAU 150 - 12

150-16 17 16.7 32 5.8 30 18 18 75 AAU 150 - 16

185-10 18.4 10.5 36 5.8 32 16 16 74 AAU 185 - 10

185-12 13 18.5 36 5.8 32 18 18 79 AAU 185 - 12

185-16 17 18.4 36 5.8 32 18 18 79 AAU 185 - 16

240-BL --- 21.2 41 7.0 38 21 21 92 AAU 240 - BL

240-10 10.5 21.2 41 7.0 38 21 21 92 AAU 240 - 10

240-12 13 21.2 41 7.0 38 21 21 92 AAU 240 - 12

240-16 17 21.2 41 7.0 38 21 21 92 AAU 240 - 16

300-BL --- 23.8 46 7.8 42 23 23 101 AAU 300 - BL

300-12 13 23.8 46 7.8 42 23 23 101 AAU 300 - 12

300-16 17 23.8 46 7.8 42 23 23 101 AAU 300 - 16

400-BL --- 26.8 50 8.0 44 24 24 107 AAU 400 - BL

500-BL --- 30.0 56 9.0 50 27 27 119 AAU 500 - BL

630-BL --- 34.0 64.4 11.0 58 32 32 139 AAU 630 - BL

Bell Mouth Lugs starts from 10mm2 & are upto 300mm2.

TINNED COPPER CABLE LUGS-SPANISH STANDARD

Sizes Stud Hole

E


A C D B L

1.5 - 4 4.3 2.4 4.0 8.7 7.0 19.0 ATN 1.5 - 4

1.5 - 5 5.3 2.4 4.0 8.7 7.0 19.0 ATN 1.5 - 5

1.5 - 6 6.4 2.4 4.0 10 7.0 20.0 ATN 1.5 - 6

2.5 - 4 4.3 2.7 4.3 8.7 7.0 19.0 ATN 2.5 - 4

2.5 - 5 5.3 2.7 4.3 8.7 7.0 19.0 ATN 2.5 - 5

2.5 - 6 6.4 2.7 4.3 10.3 7.0 21.0 ATN 2.5 - 6

2.5 - 8 8.3 2.7 4.3 12.0 7.0 23.0 ATN 2.5 - 8

4 - 4 4.3 3.1 4.8 8.7 9.5 21.5 ATN 4 - 4

4 - 5 5.3 3.1 4.8 8.7 9.5 21.5 ATN 4 - 5

4 - 6 6.4 3.1 4.8 10.3 9.5 23.5 ATN 4 - 6

4 - 8 8.3 3.1 4.8 12.5 9.5 28.5 ATN 4 - 8

6 - 4 4.3 3.8 5.5 10.3 10.0 26.0 ATN 6 - 4

6 - 5 5.3 3.8 5.5 10.3 10.0 26.0 ATN 6 - 5

6 - 6 6.4 3.8 5.5 10.3 10.0 26.0 ATN 6 - 6

6 - 8 8.3 3.8 5.5 13.9 10.0 29.0 ATN 6 - 8

6 - 10 10.5 3.8 5.5 13.9 10.0 29.0 ATN 6 - 10

10 - 4 4.3 4.7 6.9 11.9 11.5 27.5 ATN 10 - 4

10 - 5 5.3 4.7 6.9 11.9 11.5 27.5 ATN 10 - 5

10 - 6 6.4 4.7 6.9 11.9 11.5 27.5 ATN 10 - 6

10 - 8 8.3 4.7 6.9 13.5 11.5 30.5 ATN 10 - 8

10 - 10 10.5 4.7 6.9 15.0 11.5 30.5 ATN 10 - 10

10 - 12 13.2 4.7 6.9 17.0 11.5 34.0 ATN 10 - 12

16 - 5 5.3 5.6 7.8 12.0 12.0 27.5 ATN 16 - 5

16 - 6 6.4 5.6 7.8 12.0 12.0 27.5 ATN 16 - 6

16 - 8 8.3 5.6 7.8 13.5 12.0 31.0 ATN 16 - 8

16 - 10 10.5 5.6 7.8 16.0 12.0 32.0 ATN 16 - 10

16 - 12 13.2 5.6 7.8 17.0 12.0 37.5 ATN 16 - 12

25 - 6 6.4 7.1 9.5 14.0 13.5 34.0 ATN 25 - 6

25 - 8 8.3 7.1 9.5 14.0 13.5 34.0 ATN 25 - 8

25 - 10 10.5 7.1 9.5 16.0 13.5 37.0 ATN 25 - 10

25 - 12 13.2 7.1 9.5 18.0 13.5 40.0 ATN 25 - 12

35 - 6 6.4 8.2 11.0 16.5 16.0 39.0 ATN 35 - 6

35 - 8 8.3 8.2 11.0 16.5 16.0 39.0 ATN 35 - 8

35 - 10 10.5 8.2 11.0 16.5 16.0 43.0 ATN 35 - 10

35 - 12 13.2 8.2 11.0 18.0 16.0 43.0 ATN 35 - 12



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


35 - 14 14.5 8.2 11.0 20.0 16.0 48.0 ATN 35 - 14

40 - 6 6.4 9.0 11.2 17.0 17.0 44.0 ATN 40 - 6

40 - 8 8.3 9.0 11.2 17.0 17.0 44.0 ATN 40 - 8

40 - 10 10.5 9.0 11.2 17.0 17.0 44.0 ATN 40 - 10

40 - 12 13.2 9.0 11.2 18.0 17.0 44.0 ATN 40 - 12

50 - 6 6.4 9.5 12.5 18.0 20.0 45.0 ATN 50 - 6

50 - 8 8.3 9.5 12.5 18.0 20.0 45.0 ATN 50 - 8

50 - 10 10.5 9.5 12.5 18.0 20.0 49.0 ATN 50 - 10

50 - 12 13.2 9.5 12.5 18.0 20.0 49.0 ATN 50 - 12

50 - 14 14.5 9.5 12.5 22.0 20.0 54.0 ATN 50 - 14

50 - 16 16.5 9.5 14.0 25.0 23.0 62.0 ATN 50 - 16

50 - 20 21.0 9.5 14.0 30.0 23.0 68.0 ATN 50 - 20

70 - 8 8.3 11.5 15.0 22.0 20.0 47.6 ATN 70 - 8

70 - 10 10.5 11.5 15.0 22.0 20.0 51.6 ATN 70 - 10

70 - 12 13.2 11.5 15.0 22.0 20.0 51.6 ATN 70 - 12

70 - 14 14.5 11.5 15.0 22.0 20.0 62.6 ATN 70 - 14

70 - 16 16.5 11.5 15.0 22.0 20.0 62.6 ATN 70 - 16

70 - 20 21.0 11.5 15.0 30.0 20.0 62.6 ATN 70 - 20

95 - 8 8.3 13.5 17.0 25.0 22.0 55.8 ATN 95 - 8

95 - 10 10.5 13.5 17.0 25.0 22.0 55.8 ATN 95 - 10

95 - 12 13.2 13.5 17.0 25.0 22.0 55.8 ATN 95 - 12

95 - 14 14.5 13.5 17.0 25.0 22.0 66.8 ATN 95 - 14

95 - 16 16.5 13.5 17.0 25.0 22.0 66.8 ATN 95 - 16

95 - 20 21.0 13.5 17.0 30.0 22.0 66.8 ATN 95 - 20

120 - 10 10.5 15.6 20.0 29.0 27.0 71.5 ATN 120 - 10

120 - 12 13.2 15.6 20.0 29.0 27.0 71.5 ATN 120 - 12

120 - 14 14.5 15.6 20.0 29.0 27.0 71.5 ATN 120 - 14

120 - 16 16.5 15.6 20.0 29.0 27.0 71.5 ATN 120 - 16

120 - 20 21.0 15.6 20.0 29.0 27.0 71.5 ATN 120 - 20

150 - 10 10.5 16.5 21.0 30.6 32.0 78.0 ATN 150 - 10

150 - 12 13.2 16.5 21.0 30.6 32.0 78.0 ATN 150 - 12

150 - 14 14.5 16.5 21.0 30.6 32.0 78.0 ATN 150 - 14

150 - 16 16.5 16.5 21.0 30.6 32.0 78.0 ATN 150 - 16

150 - 20 21.0 16.5 21.0 30.6 32.0 78.0 ATN 150 - 20

185 - 10 10.5 18.4 23.6 34.0 34.0 84.0 ATN 185 - 10

185 - 12 13.2 18.4 23.6 34.0 34.0 84.0 ATN 185 - 12

185 - 14 14.5 18.4 23.6 34.0 34.0 84.0 ATN 185 - 14

185 - 16 16.5 18.4 23.6 34.0 34.0 84.0 ATN 185 - 16

185 - 20 21.0 18.4 23.6 34.0 34.0 84.0 ATN 185 - 20

240 - 10 10.5 21.2 26.4 38.5 37.0 90.0 ATN 240 - 10

240 - 12 13.2 21.2 26.4 38.5 37.0 90.0 ATN 240 - 12

240 - 14 14.5 21.2 26.4 38.5 37.0 90.0 ATN 240 - 14

240 - 16 16.5 21.2 26.4 38.5 37.0 90.0 ATN 240 - 16

240 - 20 21.0 21.2 26.4 38.5 37.0 90.0 ATN 240 - 20

300 - 10 10.5 23.4 28.6 42.0 40.0 96.0 ATN 300 - 10

300 - 12 13.2 23.4 28.6 42.0 40.0 96.0 ATN 300 - 12

300 - 14 14.5 23.4 28.6 42.0 40.0 96.0 ATN 300 - 14

300 - 16 16.5 23.4 28.6 42.0 40.0 96.0 ATN 300 - 16

300 - 20 21.0 23.4 28.6 42.0 40.0 96.0 ATN 300 - 20

400 - 10 10.5 26.8 32.8 48.0 37.0 104.7 ATN 400 - 10

400 - 12 13.2 26.8 32.8 48.0 37.0 104.7 ATN 400 - 12

400 - 14 14.5 26.8 32.8 48.0 37.0 104.7 ATN 400 - 14

400 - 16 16.5 26.8 32.8 48.0 37.0 104.7 ATN 400 - 16

400 - 20 21.0 26.8 32.8 48.0 37.0 104.7 ATN 400 - 20

500 - 10 10.5 29.8 38.4 55.0 46.5 115.5 ATN 500 - 10



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


500 - 12 13.2 29.8 38.4 55.0 46.5 115.5 ATN 500 - 12

500 - 14 14.5 29.8 38.4 55.0 46.5 115.5 ATN 500 - 14

500 - 16 16.5 29.8 38.4 55.0 46.5 115.5 ATN 500 - 16

500 - 20 21.0 29.8 38.4 55.0 46.5 115.5 ATN 500 - 20

630 - 10 10.5 34.5 44.7 64.0 50.0 133.1 ATN 630 - 10

630 - 12 13.2 34.5 44.7 64.0 50.0 133.1 ATN 630 - 12

630 - 14 14.5 34.5 44.7 64.0 50.0 133.1 ATN 630 - 14

630 - 16 16.5 34.5 44.7 64.0 50.0 133.1 ATN 630 - 16

630 - 20 21.0 34.5 44.7 64.0 50.0 133.1 ATN 630 - 20



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


CIRCUIT BREAKER LUG MATERIAL - E - COPPER FINISH - ELECTRO TINNED

Sizes Stud Hole E

Dimensions (mm) Product Code

d D B L

10 - 5 5.3 4.3 6.3 9 27 ACL 10 - 5

16 - 5 5.3 5.6 7.8 9 31 ACL 16 - 5

25 - 5 5.3 7 9.3 9 35 ACL 25 - 5

35 - 6 6.4 8.4 10.8 11.5 40.5 ACL 35 - 6

50 - 8 8.4 9.5 12.5 12.8 45.5 ACL 50 - 8

70 - 8 8.4 11.2 14.4 12.8 49 ACL 70 - 8

95 - 8 8.4 13.5 17.5 15.5 54 ACL 95 - 8

120 - 8 8.4 15.6 20 19 68 ACL 120 - 8

120 - 10 10.5 15.6 20 19 68 ACL 120 - 10

150 - 8 8.4 16.7 21.8 19 75 ACL 150 - 8

150 - 10 10.5 16.7 21.8 19 75 ACL 150 - 10

185 - 10 10.5 19 24.2 24.5 79 ACL 185 - 10

240 - 10 10.5 21.1 27.9 29.8 86 ACL 240 - 10

240 - 12 13.2 21.1 27.9 29.8 92 ACL 240 - 12

240 - 16 17 21.1 27.9 29.8 100 ACL 240 - 16

300 - 12 13.2 23.7 31.4 31 97 ACL 300 - 12

COPPER STANDARD WALL STARTER TERMINAL ENDS MATERIAL - E - COPPER FINISH - COPPER

Amp Rating

Cable Size

(AWG)

Stud Hole E

O.D. I.D. L Product Code

35 8 ¼ 6.35 4.72 32 AABL - 86

8 5/16` 6.35 4.72 32 AABL - 88

8 3/8` 6.35 4.72 35.18 AABL - 810

8 1/2` 6.35 4.72 42.55 AABL - 812

50 6 1/4` 7.92 5.89 32.64 AABL - 66

6 5/16` 7.92 5.89 32.64 AALB - 68

6 3/8` 7.92 5.89 32.64 AABL - 610

6 1/2` 7.92 5.89 42.55 AABL - 612

70 4 1/4` 9.04 7.14 40.64 AABL - 46

4 5/16` 9.04 7.14 40.64 AABL - 48

4 3/8` 9.04 7.14 40.64 AABL - 410

4 1/2` 9.04 7.14 40.64 AABL - 412

90 2 1/4` 10.67 8.43 43.94 AABL - 26

2 5/16` 10.67 8.43 43.94 AABL - 28

2 3/8` 10.67 8.43 43.94 AABL - 210

2 1/2` 10.67 8.43 43.94 AABL - 212

125 1/0` 1/4` 12.65 10.19 48.56 AABL -106

1/0` 5/16` 12.65 10.19 48.56 AABL -108

1/0` 3/8` 12.65 10.19 48.56 AABL -1010

1/0` 1/2` 12.65 10.19 48.56 AABL -1012

150 2/0` 1/4` 14.22 11.58 55.88 AABL - 206

2/0` 5/16` 14.22 11.58 55.88 AABL -208

2/0` 3/8` 14.22 11.58 55.88 AABL -2010

2/0` 1/2` 14.22 11.58 55.88 AABL -2012

175 3/0` 3/8` 15.62 12.93 57.15 AABL -3010

3/0` 1/2` 15.62 12.93 57.15 AABL - 3012

225 4/0` 3/8` 17.63 14.94 65.29 AABL - 4010

4/0` 1/2` 17.63 14.94 65.29 AABL - 4012

http://www.melec.com.cn/products-2.asp?stype=55



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


COLOUR COATED LUGS SOLID COPPER FORGING LUGS ACE As Per US Norm

MATERIAL - E – COPPER FINISH - COPPER

Copper Connectors WEAK BACK FERRULES MATERIAL - E - COPPER FINISH - ELECTRO TINNED

Cable Size mm2

Dimensions in mm Product Code

A C G L T P W

6 3 4.6 2 20 0.8 3 - AWB - 6

10 4.4 6 2 25 0.8 4 - AWB - 10

16 5.5 7.5 2 25 1 5 1.5 AWB - 16

25 7 9 2 30 1 7 1.5 AWB - 25

35 8 10.4 2 35 1.2 8 1.5 AWB - 35

50 9.5 11.9 2 40 1.2 9 1.5 AWB - 50

70 12 14.8 3 45 1.4 12 3 AWB - 70

120 15.5 18.7 4 55 1.6 15 3 AWB - 120

150 17 20.6 4 60 1.8 16 3.4 AWB - 150

185 18.5 22.9 4 65 2.2 18 5 AWB - 185

225 20.5 24.9 5 75 2.2 20 5 AWB - 225

240 22 26.4 5 80 2.2 21 5 AWB - 240

300 24 29.6 5 85 2.8 23 5 AWB - 300

400 28.5 34.7 7 95 3.1 27 5 AWB - 400

500 30.5 37.5 7 105 3.5 30 5 AWB - 500

625 34.5 42.5 8 115 4 33 5 AWB - 625



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


LONG BARREL CONNECTORS MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - CABLE STOP FACILITY

Cable mm2 Dimensions (mm2) Product Code

A C J

1.5 1.8 3.7 22 AC 1.5

2.5 2.4 4 22 AC 2.5

4 3.1 4.8 22 AC 4

6 3.8 5.5 22 AC 6

10 4.5 6.2 22 AC 10

16 5.4 7.1 44 AC 16

20 6.3 7.7 44 AC 20

25 6.8 8.8 47 AC 25

35 8.2 10.6 47 AC 35

50 9.5 12.4 47 AC 50

70 11.2 14.7 50 AC 70

95 13.5 17.4 54 AC 95

120 15 19.4 65 AC 120

150 16.5 21.2 65 AC 150

185 18.5 23.5 65 AC 185

240 21 26.5 89 AC 240

300 23.5 30 89 AC 300

400 28.5 36.5 90 AC 400

500 30 39 115 AC 500

550 31.7 41.5 115 AC 550

630 35 45 115 AC 630

800 39 50.6 230 AC 800

1000 43 56.2 230 AC1000

SHORT BARREL CONNECTORS MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - CABLE STOP FACILITY


A C J

1.5 1.8 3.7 12 AL 1.5

2.5 2.4 4 15 AL 2.5

4 3.1 4.8 15 AL 4

6 3.8 5.5 15 AL 6

10 4.5 6.2 20 AL 10

16 5.4 7.1 20 AL 16

20 6.3 7.7 22 AL 20

25 6.8 8.8 32 AL 25

35 8.2 10.6 36 AL 35

50 9.5 12.4 40 AL 50

70 11.2 14.7 45 AL 70

95 13.5 17.4 45 AL 95

120 15 19.4 45 AL 120

150 16.5 21.2 55 AL 150

185 18.5 23.5 60 AL 185

240 21 26.5 80 AL 240

300 23.5 30 85 AL 300

400 28.5 36.5 85 AC 400



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


500 30 39 100 AL 500

550 31.7 41.5 110 AL 550

630 35 45 110 AL 630

800 39 50.6 150 AL 800

1000 43 56.2 170 AL1000

COPPER IN - LINE CONNECTORS As per Din 46267 MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - CABLE STOP FACILITY

Cable mm2 Dimension In Mm Product Code

A C L

6 3.8 5.5 30 AADC - 6

10 4.5 6 30 AADC - 10

16 5.5 8.5 50 AADC - 16

25 7 10 50 AADC - 25

35 8.2 12.5 50 AADC - 35

50 10 14.5 56 AADC - 50

70 11.5 16.5 56 AADC - 70

95 13.5 19 70 AADC - 95

120 15.5 21 70 AADC - 120

150 17 23.5 80 AADC - 150

185 19 25.5 85 AADC - 185

240 21.5 29 90 AADC - 240

300 24.5 32 100 AADC - 300

400 27.5 38.5 150 AADC - 400

500 31 42 160 AADC - 500

630 34 44 160 AADC - 630

800 40 52 200 AADC - 800

1000 44 58 200 AADC - 1000



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


AUSTRALIAN STANDARD CONNECTORS MATERIAL - E - COPPER FINISH - ELECTRO TINNED

Cable mm2 Dimensions Product Code

A J

2.5 2.50 22.2 AAUC - 2.5

4 3.30 22.2 AAUC - 4

6 3.70 22.2 AAUC - 6

10 4.70 22.2 AAUC - 10

16 5.50 44.4 AAUC - 16

25 7.10 47.6 AAUC - 25

5 8.40 47.6 AAUC - 35

50 9.500 47.6 AAUC - 50

70 11.00 50.8 AAUC - 70

95 13.40 54.0 AAUC - 95

120 15.50 65.1 AAUC - 120

150 16.30 65.1 AAUC - 150

185 18.40 65.1 AAUC - 185

240 21.20 88.9 AAUC - 240

300 23.80 88.9 AAUC - 300

400 26.80 88.9 AAUC - 400

500 30.00 114.3 AAUC - 500

630 33.50 114.3 AAUC - 630

* Bell Mouth Lugs starts from 10 mm

2 & are upto 300 mm

2 Note - All dimensions in mm

NON TENSION CONNECTOR UP TO 33 KV MATERIAL - E - COPPER FINISH - UNTINNED APPLICATION - UP TO 33 KV

Cable mm2


A C B J S

16 5.5 7.5 22.5 47 2 AS - 16

25 7 10 22.5 47 2 AS - 25

35 8.2 11 22.5 47 2 AS - 35

50 9.5 13 25 53 3 AS - 50

70 11.5 15 25 53 3 AS - 70

95 13.5 17.5 25 53 3 AS - 95

120 15.5 20 30 63 3 AS - 120

150 17 22 35 73 3 AS - 150

185 19 24 40 84 4 AS - 185

240 21 26 43 90 4 AS - 240



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


FULL TENSION CONNECTOR UP TO 36 KV MATERIAL - E - COPPER FINISH - UNTINNED FEATURES - CABLE STOP FACILITY APPLICATION - UP TO 36 KV

Cable mm2


A C J

6 3.5 6.5 65 ACT - 6

10 4.5 8.5 80 ACT - 10

16 5.5 8.5 95 ACT - 16

25 7 10 95 ACT - 25

35 8.2 12.5 95 ACT - 35

50 10 14.5 110 ACT - 50

70 11.5 16.5 110 ACT - 70

95 13.5 21 145 ACT - 95

120 15 23.5 160 ACT - 120

150 16.5 25.5 180 ACT - 150

185 18.5 31.5 260 ACT - 185

240 21 34.5 310 ACT - 240

300 23.5 38.5 360 ACT - 300



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


COPPER CONNECTORS WITH SOLID BARRIER MATERIAL - E - COPPER FINISH - COPPER

Cable mm2

Dimensions in mm Product Code mm2 A AL L C

35 35 8.2 8.2 60 11 ASB35

35 50 8.2 10 60 13 ASB3550

50 50 10 10 60 13 ASB50

50 70 10 11.5 65 16 ASB5070

70 70 11.5 11.5 65 16 ASB70

70 95 11.5 14 85 20 ASB7095

95 95 14 14 85 20 ASB95

95 120 14 15.5 95 22 ASB9512

120 120 15.5 15.5 95 22 ASB120

120 150 15.5 17 105 23.5 ASB1215

150 150 17 17 105 23.5 ASB150

150 185 17 19 115 24 ASB1518

120 185 15.5 19 115 24 ASB1218

185 185 19 19 115 24 ASB185

185 240 19 21.5 125 28 ASB1824

240 240 21.5 21.5 125 28 ASB240

150 240 17 21.5 125 28 ASB1524

240 300 21.5 24.5 140 31.5 ASB2430

185 300 19 24.5 140 31.5 ASB1830

300 300 24.5 24.5 140 31.5 ASB300

300 400 24.5 27.5 170 36.5 ASB3040

400 400 27.5 27.5 170 36.5 ASB400

TINNED SCREW SLEEVES MATERIAL - E - COPPER FINISH - ELECTRO TINNED FEATURES - WITH INSPECTION HOLE SCREWS - ZINC PLATED STEEL


A J

6 3.5 20 ATBSS - 6

10 4.4 30 ATBSS - 10

16 5.5 40 ATBSS - 16

25 6.8 45 ATBSS - 25

35 8.2 45 ATBSS - 35

50 9.5 48 ATBSS - 50

70 11.2 52 ATBSS - 70

95 13.4 55 ATBSS - 95

120 15 55 ATBSS - 120

150 16.5 60 ATBSS - 150

185 19 60 ATBSS - 185

240 21 65 ATBSS - 240

300 23.5 65 ATBSS - 300



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


COPPER / TINNED COPPER 'C' TYPE CONNECTOR MATERIAL - E - COPPER FINISH - ELECTRO TINNED

Sizes B D E A C L Product Code

4-4 6.55 9.85 1.5 - 3.8 8.15 ACC 4 - 4

10-6 8.05 11.90 2.28 - 4.32 13.00 ACC 10 - 6

25-6 10.5 18.7 6.9 6.3 7.7 17.5 ACC 25 - 6

25-10 12.0 19.5 3.9 - 7.3 17.6 ACC 25 - 10

25-25 14.1 20.6 4.2 - 9.1 17.7 ACC 25 - 25

35-25 15.4 25.2 9.3 9.6 9.3 21.2 ACC 35 - 25

35-35 18.2 26.7 5.1 - 11.9 21.3 ACC 35 - 35

70-35 18.4 33.3 11.3 11.9 11.9 27.2 ACC 70 - 35

70-70 21.5 34.2 6.2 - 11.2 27.2 ACC 70 - 70

95-35 22.3 42.0 13.1 13.2 14.8 29.2 ACC 95 - 35

95-70 24.8 41.0 14.3 - 14.0 29.4 ACC 95 - 70

95-95 27.5 39.9 8.0 - 14.3 29.1 ACC 95 - 95

120-120 36.1 45.2 15.0 14.8 16.4 30.2 ACC 120 - 120

185-95 36.6 53.8 18.9 17.7 20.5 35.2 ACC 185 - 95

150-150 36.06 45.15 15.00 14.78 16.42 30.20 ACC 150 - 150

185-185 36.62 53.77 18.92 17.22 20.45 35.20 ACC 185 - 185

Other Range of C Clamps C Clamp 6 C Clamp 8



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


T – CONNECTORS

• Standard type • Material - E - Copper • Finish - Copper / Tin Plated

Cable mm2

Dimensions Product Code A C J L

1.5 1.8 3.3 30 12 ATC - 1.5

2.5 2.3 4.2 30 12 ATC - 2.5

4 3.0 5.0 30 12 ATC - 4

6 4.0 6.0 35 14 ATC - 6

10 4.5 7.0 35 14 ATC - 10

16 5.5 8.5 50 21 ATC - 16

25 7.0 10.0 55 23 ATC - 25

35 8.5 12.0 70 30 ATC - 35

50 10.0 14.0 80 34 ATC - 50

70 12.0 16.5 85 35 ATC - 70

95 13.5 18.0 90 36 ATC - 95

120 15.0 19.5 95 38 ATC - 120

150 16.5 21.0 110 44 ATC - 150

185 19.0 24.0 115 45 ATC - 185

240 21.0 26.0 130 52 ATC - 240

Also available in aluminium on request.

CROSS- CONNECTORS • Standard type • Material - E - Copper • Finish - Copper / Tin Plated

Also available in aluminium on request.

Cable mm2 A C J L Product Code

1.5 1.8 3.3 30 12 APC - 1.5

2.5 2.3 4.2 30 12 APC - 2.5

4 3.0 5.0 30 12 APC - 4

6 4.0 6.0 35 14 APC - 6

10 4.5 7.0 35 14 APC - 10

16 5.5 8.5 50 21 APC - 16

25 7.0 10.0 55 23 APC - 25

35 8.5 12.0 70 30 APC - 35

50 10.0 14.0 80 34 APC - 50

70 12.0 16.5 85 35 APC - 70

95 13.5 18.0 90 36 APC - 95

120 15.0 19.5 95 38 APC - 120

150 16.5 21.0 110 44 APC - 150

185 19.0 24.0 115 45 APC - 185

240 21.0 26.0 130 52 APC - 240



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


Copper Reducer Pin Type Terminal Ends MATERIAL - E- COPPER FINISH - ELECTRO TINNED

Cable mm2 Dimensions Product Code

A C D D1 B G+H J

2.5 2.5 4.7 3.8 3.3 6 10 20 APCC - 7

4 2.8 4.7 3.8 3.3 6 10 20 APCC - 16

6 3.1 4.7 3.8 3.3 6 10 20 APCC - 18

10 3.8 5.5 3.8 3.3 9 10 23 APCC - 20

16 5.3 7.1 3.8 3.3 12 13 30 APCC - 2

25 7 9 6 5.5 12 15 32 APCC - 25

25 7 9 7.5 6.5 12 20 37 APCC - 3

35 8 10 7.5 6.5 12 20 37 APCC - 4

50 9.2 11.2 7.5 6.5 16 20 41 APCC - 26

70 11.5 13.8 7.5 6.5 18 20 43 APCC - 27

70 11.5 13.8 11.5 10.5 18 25 48 APCC - 6

70 11.5 13.8 11.5 10.5 18 32 55 APCC - 28

95 12.8 15.6 11.5 10.5 20 25 51 APCC - 29

95 12.8 15.6 7.5 6.5 20 22 48 APCC - 31

95 12.8 15.6 15.6 14 20 27 53 APCC - 8

120 14.8 17.8 11.5 10.5 22 25 53 APCC - 32

120 14.8 17.8 7.5 6.5 22 22 50 APCC - 34

120 14.8 17.8 11.5 10.5 22 32 60 APCC - 35

150 16 19.6 11.5 10.5 26 32 64 APCC - 37

185 18 22 11.5 10.5 32 32 70 APCC - 38

240 22 26 16 15 38 42 88 APCC - 44

300 24 28.7 16 15 42 42 92 APCC - 45

400 28 33.2 15.6 14 46 32 90 APCC - 48

Aluminum Lugs BOLTED ALUMINIUM LUG

Size Bolt Cross Section Of conductor (mm2)

Shear Head A Or B

Product Code

16-50 2 16-25 B

ABL 16-50 35-50 A

70-95 2 70 B

ABL 70-95

95 A

120-150 2 120 B

ABL 120-150 150 A

185-240 3 185 B

ABL 185-240 240 A



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


BOLTED BIMETAL LUG

Size Bolt Cross Section Of conductor

(mm2)

Shear Head A

Or B

Product Code

16-50 2 16-25 B

ABML 16-50

35-50 A

70-95 2 70 B

ABML 70-95

95 A

120-150 2 120 B

ABML 120-150

150 A

185-240 3 185 B

ABML 185-240

240 A

ALUMINIUM FORGING LUGS (As Per Din 46329) MATERIAL - ALUMINIUM FINISH - NATURAL / PASSIVATED ALUMINIUM

Cable mm2

Stud Hole E

Bolt Dimensions Product Code

A C D B L-1

16 8.4 M 8 5.8 12 20 30 50 AAFL 16-8

25 8.4 M 8 6.8 12 20 30 50 AAFL 25-8

35 8.4 M 8 8 14 25 42 62 AAFL 35-8

50 8.4 M 8 9.8 16 25 42 62 AAFL 50-8

70 8.4 M 8 11.2 16 25 52 72 AAFL 70-8

95 10.5 M 10 13.2 22 25 56 75 AAFL 95-10

120 10.5 M 10 14.7 22 30 56 80 AAFL 120-10

150 10.5 M 10 16.3 25 30 60 90 AAFL 150-10

185 10.5 M 10 18.3 28 30 60 91 AAFL 185-10

240 10.5 M 10 21 32 38 70 103 AAFL 240-10

300 13 M 12 23.3 34 38 70 103 AAFL 300-12

400 13 M 12 26 38 38 73 116 AAFL 400-12

500 13 M 12 29 44 44 79 122 AAFL 500-12



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


ALUMINIUM LUGS MATERIAL - ALUMINIUM FINISH - NATURAL/PASSIVATED ALUMINIUM

Size mm2

Stud Hole E

A C D B J Product Code

2.5 3.7 2.6 5.5 7.0 10.5 21.5 AAH 2.5 - 4

4 4.2 2.9 5.5 7.0 10.5 21.5 AAH 4 - 4

4 5.2 2.9 5.5 12.0 10.5 27.5 AAH 4 - 5

6 5.2 3.5 5.5 8.0 10.5 27.5 AAH 6 - 5

6 6.4 3.5 5.5 12.0 10.5 27.5 AAH 6 - 6

10 6.4 4.4 7.4 10.0 13.5 34.5 AAH 10 - 6

10 8.2 4.4 7.4 15.0 13.5 34.5 AAH 10 - 8

16 6.4 5.4 8.3 11.0 19.5 43.5 AAH 16 - 6

16 8.2 5.4 8.3 11.0 19.5 43.5 AAH 16 - 8

16 10.2 5.4 8.3 18.0 19.5 43.5 AAH 16 - 10

25 8.2 7.0 10.0 14.0 24.0 52.0 AAH 25 - 8

25 10.2 7.0 10.0 20.0 24.0 52.0 AAH 25 - 10

25 12.7 7.0 10.0 20.0 24.0 52.0 AAH 25 - 12

35 8.2 8.0 10.8 15.0 27.0 56.0 AAH 35 - 8

35 10.2 8.0 10.8 20.0 27.0 56.0 AAH 35 - 10

50 8.2 9.3 13.0 18.0 33.0 65.0 AAH 50 - 8

50 10.2 9.3 13.0 23.0 33.0 65.0 AAH 50 - 10

50 12.7 9.3 13.0 23.0 33.0 65.0 AAH 50 - 12

70 8.2 11.6 16.0 22.0 39.0 73.0 AAH 70 - 8

70 10.2 11.6 16.0 22.0 39.0 73.0 AAH 70 - 10

70 12.7 11.6 16.0 22.0 39.0 73.0 AAH 70 - 12

95 10.2 12.9 17.1 25.0 42.0 78.0 AAH 95 - 10

95 12.7 12.9 17.1 25.0 42.0 78.0 AAH 95 - 12

95 16.2 12.9 17.1 25.0 42.0 78.0 AAH 95 - 16

120 10.2 14.8 19.6 28.0 48.0 89.0 AAH 120 - 10

120 12.7 14.8 19.6 28.0 48.0 89.0 AAH 120 - 12

120 16.2 14.8 19.6 28.0 48.0 89.0 AAH 120 - 16

150 10.2 16.1 21.5 31.0 51.0 96.0 AAH 150 - 10

150 12.7 16.1 21.5 31.0 51.0 96.0 AAH 150 - 12

150 16.2 16.1 21.5 31.0 51.0 96.0 AAH 150 - 16

185 10.2 18.5 24.0 34.0 54.0 102 AAH 185 - 10

185 12.7 18.5 24.0 34.0 54.0 102 AAH 185 - 12

185 16.2 18.5 24.0 34.0 54.0 102 AAH 185 - 16

225 12.7 20.6 27.0 39.0 60.0 114 AAH 225 - 12

240 12.7 22.0 28.6 40.0 66.0 124 AAH 240 - 12

240 16.2 22.0 28.6 40.0 66.0 124 AAH 240 - 16

300 16.2 25.0 32.0 46.3 70.5 138.5 AAH 300 - 16

300 20.3 25.0 32.0 46.3 70.5 138.5 AAH 300 - 20

400 20.3 29.0 37.5 54.1 84.0 158 AAH 400 - 20

500 20.3 30.0 41.0 58.0 90.0 170 AAH 500 - 20

630 20.3 35.0 46.0 66.0 103.5 188.5 AAH 630 - 20

800 - 39.0 51.0 73.0 115.5 218.5 AAH - 800

1000 - 43.5 57.0 81.0 150 270 AAH - 1000



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


ALUMINIUM 3 CORE SECTOR CABLE LUGS MATERIAL - ALUMINIUM FINISH - NATURAL / PASSIVATED ALUMINIUM

Cable mm2

Stud Hole E


A B C D E F G H d1Ø

25

8

4.1 15.2 8.4 AAL3 - 25-8

10 65 25 8 17 12 1

10.4 AAL3 - 25-10

12

2.9 21 12.5 AAL3 - 25-12

35

8

4.4 17.6 8.4 AAL3 - 35-8

10 68 30 8 17 12 1

10.4 AAL3 - 35-10

12

3.6 21 12.5 AAL3 - 35-12

50

10

4.5 20.3 8.4 AAL3 - 50-10

12 71 32 10 17 12 1

10.4 AAL3 - 50-12

16

2.9 21 12.5 AAL3 - 50-16

70

10

5 23.2 10.4 AAL3 - 70-10

12 76 35.5 11 17 12 1

12.5 AAL3 - 70-12

16

4.6 26 16.5 AAL3 - 70-16

95

10

10.4 AAL3 - 95-10

12 82 39 14 17 12 1.5 5.7 27.7 12.5 AAL3 - 95-12

16

16.5 AAL3 - 95-16

120

12

10.4 AAL3 - 120-12

16 88 44 15 17 12 1.5 6.5 31 12.5 AAL3 - 120-16

20

16.5 AAL3 - 120-20

150

12

12.4 AAL3 - 150-12

16 100 47.5 16 20.5 16 1.5 7.2 34.7 16.5 AAL3 - 150-16

20

20.5 AAL3 - 150-20

185

12

12.4 AAL3 - 185-12

16 106 47.5 16 20.5 16 105 7.2 34.7 12.4 AAL3 - 185-16

20

20.5 AAL3 - 185-20

240 20 116 55.5 20.5 22 18 2 5.7 43.6 20.5 AAL3 - 240-20

300 20 128.5 60.5 23 25 20 2 9.7 49.2 20.5 AAL3 - 300-20



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


ALUMINIUM 3 CORE SECTOR FERRULES MATERIAL - ALUMINIUM FINISH - NATURAL / PASSIVATED ALUMINIUM

Cable Size mm2

A Product Code

25 66 AAL -3F- 25

35 70 AAL -3F- 35

50 74 AAL -3F- 50

70 78 AAL -3F- 70

95 84 AAL -3F- 95

120 91 AAL -3F- 120

150 102 AAL -3F- 150

185 108 AAL -3F- 185

240 118 AAL -3F- 240

300 130 AAL -3F- 300

400 140 AAL -3F- 400

500 155 AAL -3F- 500

630 172 AAL -3F- 630

Aluminum Connectors BOLTED ALUMINIUM CONNECTOR

Size Bolt Cross Section Of conductor (mm2)

Shear Head A Or B

Product Code

16-50 4 16-25 B

ABC 16-50 35-50 A

70-95 4 70 B

ABC 70-95 95 A

120-150 4 120 B

ABC 120-150 150 A

185-240 6 185 B

ABC 185-240 240 A

ALUMINIUM THROUGH CONNECTORS MATERIAL - ELECTROLYTIC GRADE AL 99.5 FINISH - BRIGHT OR ELECTRO-TINNED FEATURES - BARREL PREFILLED WITH OXIDE INHIBITING COMPOUND & CAPPED AT BOTH END


A C J

16 5.5 16.0 90.5 ATAC - 16

25 6.5 16.0 90.5 ATAC - 25

35 8.0 16.0 90.5 ATAC - 35

50 9.0 20.0 106.5 ATAC - 50

70 11.0 20.0 106.5 ATAC - 70

95 12.5 20.0 106.5 ATAC - 95

120 13.7 25.0 133.0 ATAC - 120

150 15.5 25.0 135.0 ATAC - 150

185 17.0 32.0 143.5 ATAC - 185

240 19.5 32.0 146.0 ATAC - 240

300 22.5 34.0 144.5 ATAC - 300

Note: All dimension in mm



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


ALUMINIUM SPLICE FOR LV & MV (UPTO 30 KV) FOR SIMILAR CABLE CROSS SECTIONAL AREAS MATERIAL - AL 99.5 FINISH - NATURAL / PASSIVATED ALUMINIUM

Cable MM2

Dimensions (MM2) Product Code A C L B J

16 5.5 16 76 43 90 AASC 16

25 6.5 16 76 43 90 AASC 25

35 8 16 80 43 92 AASC 35

50 9 20 93 53 110 AASC 50

70 11 20 96 53 110 AASC 70

95 12.5 20 98 53 110 AASC 95

120 13.7 25 117 66 135 AASC 120

150 15.5 25 118 66 135 AASC 150

185 17 32 122 70 146 AASC 185

240 19.5 32 124 70 146 AASC 240

300 23.3 36 185 100 208 AASC 300

400 26 36 190 100 208 AASC 400

500 29.1 47 190 107 222 AASC 500

630 33.5 47 197 107 222 AASC 630

800 37.5 60 232 127 274 AASC 800

1000 42 60 240 128 276 AASC 1000

ALUMINIUM SPLICE FOR LV & MV (UPTO 30 KV) FOR DISSIMILAR CABLE CROSS SECTIONAL AREAS MATERIAL - AL 99.5 FINISH - NATURAL / PASSIVATED ALUMINIUM

Cable mm2


A A1 C L B1 B2 J

25 - 16 6.-5 5.5 16 77 43 43 90 AADC 25 - 16

35 - 25 8 6.5 16 77 43 43 90 AADC 35 - 25

50 - 25 9 6.5 20 91 51 51 108 AADC 50 - 25

50 - 35 9 8 20 91 51 51 108 AADC 50 -35

70 - 35 11 8 20 92 51 52 108 AADC 70 - 35

70 - 50 11 9 20 95 52 53 110 AADC 70 - 50

95 - 35 12.5 8.5 20 93 52 52 108 AADC 95 - 35

95 - 50 12.5 9 20 95 52 53 110 AADC 95 - 50

95 - 70 12.5 11 20 95 52 53 109 AADC 95 - 70

120 - 35 13.7 8 25 111 64 64 132 AADC 120 - 35

120 - 50 13.7 9 25 111 64 64 132 AADC 120 - 50

120 - 95 13.7 12.5 25 112 64 64 132 AADC 120 - 95

150 - 50 15.5 9.5 25 116 64 66 135 AADC 150 - 50

150 - 70 15.5 11 25 116 64 66 135 AADC 150 - 70

150 - 95 15.5 12.5 25 116 64 66 135 AADC 150 - 95

150 - 120 15.5 13.7 25 116 64 66 135 AADC 150 -120

185 - 70 17 11 32 118 69 69 144 AADC 185 - 70

185 - 95 - - 32 122 69 72 146 AADC 185 - 95

185 - 120 17 13.7 32 119 70 70 145 AADC 185 - 120

185 - 150 17 15.5 32 121 70 71 146 AADC 185 - 150

240 - 70 19.5 11 32 122 69 73 147 AADC 240 - 70

240 - 95 19.5 12.5 32 122 69 72 146 AADC 240 - 95

240 - 120 19.5 13.7 32 122 69 72 146 AADC 240 - 120

240 - 150 19.5 15.5 32 122 69 72 146 AADC 240 - 150

240 - 185 19.5 17 32 122 69 71 145 AADC 240 - 185



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


Bimetallic Lugs ALUMINIUM - COPPER BI-METAL TERMINALS

Section mm2

A B G C x C' D E F J L P Q U

16 5.5 16.0 12.0 min. 19.0 x 19.0 10.5 45.5 40.0 - 78.5 14.0 9.0 4.5

25 6.5 16.0 12.0 max 30.0 x 30.0 10.5 45.5 40.0 - 78.5 14.0 9.0 4.5

35 8.0 16.0 12.0

min 24.0 x 24.0 max 41.0 x 41.0

12.8 45.5 40.0 - 78.5 14.0 9.0 4.5

50 9.0 20.0 14.8 12.8 45.5 40.0 - 88.5 14.0 11.0 5.0

70 11.0 20.0 14.8 12.8 45.5 40.0 - 88.5 14.0 11.0 5.0

95 12.5 20.0 14.8 12.8 45.5 40.0 - 88.5 14.0 11.0 5.0

120 13.7 25.0 18.8

min 29.0 x 29.0 max 41.0 x 41.0

12.8 60.8 55.5 - 108.5 14.0 13.0 6.4

150 15.5 25.0 18.8 12.8 60.8 55.5 - 108.5 14.0 13.0 6.4

185 17.0 32.0 23.8 12.8 59.7 55.5 - 108.5 14.0 17.0 6.9

240 19.5 32.0 23.8 12.8 59.7 55.5 - 108.5 14.0 17.0 6.9

300 23.3 40.0 28.0 min 35.0 x 35.0 16.5 94 89.0 - 153.5 14.0 21.0 8.8

400 26.0 40.0 28.0 max 41.0 x 41.0 16.5 94 89.0 - 153.5 14.0 21.0 8.8

500 29.1 47.0 36.8 60.0 x 60.0 4 x 9.0 95.7 90.0 30.0 263.5 14.0 25.0 8.9

630 32.5 47.0 36.8 +/- 1.0 4 x 9.0 95.7 90.0 30.0 263.5 14.0 25.0 8.9

800 37.5 60.0 45.0

80.0 x 80.0 +/- 1.0

4 x 11.0 128.7 120.5 40.0 298.5 14.0 32.0 11.2

1000 42.0 60.0 45.0 4 x 11.0 128.7 120.5 40.0 298.5 14.0 32.0 11.2

1200 45.5 65.0 53.8 4 x 11.0 139.9 131.0 40.0 328.5 14.0 34.0 12.1

1600 53.0 70.0 53.8 125.0 x 125.0

+/- 1.0 9 x 11.0 138.7 134.0 45.0 375.0 14.0 36.0 12.7

Tolerances Max (+/- 0.3) 0 -2

min (+/- 0.5)

max max min min

PRE-INSULATED BIMETAL LUG CPTAU Material - E –Cu; AL-99.6% Features - Pre – Insulated Bimetal Lug is designed to connect the insulated cable (include ABC cable). The waterproof end cap can prevent water into the barrel. It is coloured differently to distinguish the cable sizes. It is marked with type, cable size, die size, inner cable length and number of crimping.

Sizes Stud Hole E

Dimensions (mm) Length (mm) Product Code

D B L

16-10 10.5 16 20 73 APIB - 16

25-12 13 20 24 98.5 APIB - 25

35-12 13 20 24 98.5 APIB - 35

50-12 13 20 24 98.5 APIB - 50

54.6-12 13 20 24 98.5 APIB - 54.6



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


70-12 13 20 24 98.5 APIB - 70

95-12 13 20 24 98.5 APIB - 95

SPECIAL BIMETALLIC LUGS MATERIAL : Aluminium Barrel : 99.6% Copper Palm : 99.95% Final Metal State : Fully Annealed, Including Joint. Joining method friction welding, welding area more than nominal conductor area. Finish natural.

Size mm2 Stud Hole E

A B C D F P L Product Code

50 14 13.5 70 26 31 4.8 60 143 ASBL - 50

120 14 15.5 70 26 31 4.8 60 143 ASBL - 120

BIMETALLIC LUGS WITH CENTRE PALM CONDUCTIVITY : Aluminium 61.8% IACS (MIN) Copper 99.7% IACS


A B C D F L Product Code

70 11 10 54 16 26 11 111 ABCP - 70

120 11 12 54 20 27 11 110 ABCP - 120

185 11 16 55 27 27 11 111 ABCP - 185

300 11 20 53 32 27 11 110 ABCP - 300

CONDUCTIVE MATERIAL : Aluminium Barrel : 99.6% Copper Palm : 99.95% Final Metal State : Fully Annealed, Including Joint. Joining method : Friction welding, welding area more than nominal conductor area. Finish natural.


A B C D F L Product Code

240 17 21 65 32 35 13 131 ABCP - 240



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


BIMETALLIC LUGS WITH EXTENDED PALM CONDUCTIVE MATERIAL : Aluminium Barrel : 99.6% Copper Palm : 99.95% Final Metal State : Fully Annealed, Including Joint. Joining method : Friction welding, welding area more than nominal conductor area. Finish natural.

Size mm2

A B C C1 D F T AL CU P L Product Code

70 25 12.5 13 45 25 58 6 63 77 67 140 ABEP - 70

95 25 14 5 13 45 25 58 6 63 77 67 140 ABEP - 95

120 25 17 13 45 25 58 6 63 77 67 140 ABEP - 120

150 30 2 18 5 13 45 25 58 7 63 77 67 140 ABEP - 150

185 30.2 20 13 45 25 58 7 63 77 67 140 ABEP - 185



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


ALUMINIUM LUGS WITH COPPER RING

Size mm2 E A C D B J Product Code

50 8.2 9.3 13.0 18.0 33.0 65.0 AALC 50 - 8

50 10.2 9.3 13.0 23.0 33.0 65.0 AALC 50 - 10

50 12.7 9.3 13.0 23.0 33.0 65.0 AALC 50 - 12

70 8.2 11.6 16.0 22.0 39.0 73.0 AALC 70 - 8

70 10.2 11.6 16.0 22.0 39.0 73.0 AALC 70 - 10

70 12.7 11.6 16.0 22.0 39.0 73.0 AALC 70 - 12

95 10.2 12.9 17.1 25.0 42.0 78.0 AALC 95 - 10

95 12.7 12.9 17.1 25.0 42.0 78.0 AALC 95 - 12

95 16.2 12.9 17.1 25.0 42.0 78.0 AALC 95 - 16

120 10.2 14.8 19.6 28.0 48.0 89.0 AALC 120 - 10

120 12.7 14.8 19.6 28.0 48.0 89.0 AALC 120 - 12

120 16.2 14.8 19.6 28.0 48.0 89.0 AALC 120 - 16

150 10.2 16.1 21.5 31.0 51.0 96.0 AALC 150 - 10

150 12.7 16.1 21.5 31.0 51.0 96.0 AALC 150 - 12

150 16.2 16.1 21.5 31.0 51.0 96.0 AALC 150 - 16

185 10.2 18.5 24.0 34.0 54.0 102 AALC 185 - 10

185 12.7 18.5 24.0 34.0 54.0 102 AALC 185 - 12

185 16.2 18.5 24.0 34.0 54.0 102 AALC 185 - 16

225 12.7 20.6 27.0 39.0 60.0 114 AALC 225 - 12

240 12.7 22.0 28.6 40.0 66.0 124 AALC 240 - 12

240 16.2 22.0 28.6 40.0 66.0 124 AALC 240 - 16

300 16.2 25.0 32.0 46.3 70.5 138.5 AALC 300 - 16

300 20.3 25.0 32.0 46.3 70.5 138.5 AALC 300 - 20

400 20.3 29.0 37.5 54.1 84.0 158 AALC 400 - 20

500 20.3 30.0 41.0 58.0 90.0 170 AALC 500 - 20

630 20.3 35.0 46.0 66.0 103.5 188.5 AALC 630 - 20



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


BIMETALLIC CONNECTOR BI - METALLIC CONNECTOR Bi- Metallic connectors are used for joining aluminium & copper circular conductors. They are particularly useful, when copper is used as earthing in aluminium lightning protection systems.

Conductor Dia. Product Code

8mm Dia, Al conductor to 8mm Dia, Cu conductor.

ABI - 8

8mm Dia, Al conductor to 25 x 3 Cu tape,

ABI – 825

20 x 3 Al tape to 20 x 3 Cu tape, ABI - 203

25 x 3 Al tape to 25 x 3 Cu tape, ABI - 253

CONDUCTIVE MATERIAL : Aluminium : 99.6% Copper : 99.95% Final Metal State : Fully Annealed, Including Joint. Joining method friction welding, welding area more than nominal conductor area. Finish natural. Aluminium barrel are chemically treated to reduce contact resistance and corrosion and are filled electrically conductive corrosion inhabitant with a jointing compound and capped.

ABI – 253 ABI – 825 ABI - 8

UNIVERSAL CABLE CONNECTOR



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


ALUMINIUM - COPPER BI - METAL CONNECTOR / SPLICE Al- Cu Bi- Metal splice are used for joining Aluminum Cable to Copper Cable.

Cable Area mm2 Dimensions

Al. Solid or Stranded

Copper Stranded

E A H F D G L Product Code

16 16 5.5 5.6 16 43 12.2 29 88 ABS 16 - 16

25 16 6.8 5.5 16 35 12.2 20 70 ABS 25 - 16

25 25 6.5 7 16 43 12.2 29 88 ABS 25 - 25

35 16 8 5.5 16 41 12.2 20 76 ABS 35 - 16

35 25 8 7 16 41 12.2 25 82 ABS 35 - 25

35 35 8 8 16 43 12.2 29 88 ABS 35 - 35

50 25 9.8 7 16 41 12.2 25 85 ABS 50 - 25

50 35 9.8 8.2 16 41 12.5 30 90 ABS 50 - 35

50 50 9 9.5 20 43 12.2 29 88 ABS 50 - 50

70 35 11.2 8.2 18.5 45 12.5 30 95 ABS 70 - 35

70 50 11.2 10 18.5 45 14.5 35 100 ABS 70 - 50

70 70 11 11 20 43 21 33 90 ABS 70 - 70

95 50 13.2 10 22 50 14.5 35 105 ABS 95 - 50

95 70 13.2 11.5 22 50 16.5 40 110 ABS 95 - 70

95 95 12.5 13 20 43 21 33 90 ABS 95 - 95

120 70 14.7 11.5 23 55 16.5 40 116 ABS 120 - 70

120 95 14.7 13.5 23 55 19 42 118 ABS 120 - 95

120 120 13.7 14.2 25 59 21 33 107 ABS 120 - 120

150 95 16.3 13.5 25 55 19 42 120 ABS 150 - 95

150 120 16.3 15.5 25 55 21 44 122 ABS 150 - 120

150 150 15.5 16 25 59 21 33 107 ABS 150 - 150

185 120 18.3 15.5 28.5 59 21 44 128 ABS 185 - 120

185 150 18.3 17 28.5 59 23.5 45 130 ABS 185 - 150

185 185 17 18 32 59 26.2 43 120 ABS 185 - 185

240 150 21 17 32 60 23.5 45 132 ABS 240 - 150

240 185 21 19 32 60 25.5 47 135 ABS 240 - 185

240 240 21 21.5 32 60 29 52 140 ABS 240 - 240

Made to order terminals as per the customers specification / samples / diagrams also available.



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


MECHANICAL COPPER CABLE - LUGS BOLTED WITH 2 SCREWS AND 4 SCREWS MATERIAL - E - COPPER FINISH - ELECTRO TINNED

Cable mm2


A F B H Screw Type

10 4 6 15 32,5 M - 5 1 A2B - 10

16 5.1 8.5 17 37 M - 5 1 A2B - 16

25 6.3 8.5 18.75 42 M - 5 1 A2B - 25

35 7.5 10.5 21.50 49 M - 5 1 A2B - 35

50 9.5 10.5 23 56.5 M - 6 2 A4B - 50

75 11 13.25 26 61 M - 6 2 A4B - 75

100 13 14.30 29 65 M - 6 2 A4B - 100

120 14 14.80 32 71 M - 6 2 A4B - 120

170 16 16 33 81 M - 8 2 A4B - 170

200 17 17 35 85 M - 8 2 A4B - 200

250 18 17 38 87.5 M - 8 2 A4B - 250

300 21 19.8 45 118 M - 10 2 A4B - 300

400/500 25.5 22 53 132 M - 10 2 A4B - 400/500

700 34 22 60 150 M - 10 2 A4B - 700

SPLIT BOLT CONNECTORS ‘ACE' manufactures a vast range of line taps to meet the materials & dimensional specifications laid by different international standards. Brass line taps are made with high tensile brass as per BS 2874 - CZ 112. Threads are formed by rolling process giving the nut extra clamping force. Pressure pads are made from extruded bars (not cast), preventing the pads from cracking. Brass line taps are manufactured in passivated natural brass with electro tinned finish. They are also supplied in high conductivity copper.

Size (mm2) A B CA / F DA / F E Product Code

6 19.85 4.00 12.70 13..35 4.80 ASBC - 6

10 26.75 4.70 12.70 19.00 5.60 ASBC - 10

16 26.00 5.70 12.70 19.00 5.60 ASBC - 16

25 28.00 7.30 16.00 19.00 5.60 ASBC - 25

35 35.00 7.80 18.50 24.00 6.35 ASBC - 35

50 42.00 9.70 24.10 27.20 8.65 ASBC - 50

70 44.50 11.50 24.10 27.20 8.65 ASBC - 70

95 50.00 14.40 26.50 35.40 9.40 ASBC - 95

120 57.50 16.20 30.00 35.40 12.00 ASBC - 120

120 57.50 16.20 30.00 35.40 12.00 ASBC - 150

185 57.50 18.20 31.75 38.00 12.00 ASBC - 185

240 72.50 22.00 40.00 48.20 14.25 ASBC - 240

300 72.50 24.00 42.00 50.00 14.25 ASBC - 300

400 76.50 26.00 48.00 56.00 16.00 ASBC - 400

500 80.00 30.00 55.00 65.00 16.00 ASBC - 500



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


SPLIT BOLT CONNECTORS – ROUND SPLIT BOLT CONNECTORS – ROUND

Cable Size mm2

Dimensions In mm Product Code

A

16 5.3 ASRC - 16

25 6.9 ASRC - 25

35 8.3 ASRC - 35

50 9.5 ASRC - 50

70 10.9 ASRC - 70

95 12.9 ASRC - 95

120 15 ASRC - 120

150 16.6 ASRC - 150

185 18.5 ASRC - 185

OTHER COPPER/ ALUMINUM CONNECTORS COPPER SOLDERLESS LUGS (SLU & SAU TYPE) Single Hole, Single Collar

Concave pressure bar and V - bottom collar ensures firm, permanent grip and positive contact.

MATERIAL- 100% pure electrolytic copper

Copper Conductor

Current Rating

Dimension (Inches) Product Code

Size Range (Amps) J D G E T B C A

14 - 6 35 1.19 0.38 0.23 0.25 0.07 0.43 0.5 0.33 ASW - 35

14 - 4 50/70 1.31 0.5 0.25 0.28 0.08 0.43 0.56 0.38 ASW - 70

12 - 2` 90 1.55 0.5 0.25 0.34 0.09 0.5 0.65 0.47 ASW - 90

8 - 1/0` 125 1.97 0.63 0.5 0.28 0.13 0.63 0.88 0.62 ASW - 125

4 - 3/0` 175 2.19 0.75 0.44 0.5 0.13 0.75 1.03 0.71 ASW - 175

6 - 4/0` 225 2.38 1 0.47 0.56 0.13 1 1.17 0.75 ASW - 225

1/0-350 300 3.16 1 0.5 0.94 0.19 1.23 1.39 1 ASW - 300

4/0 - 500 400 4.25 1.5 0.88 1 0.19 1.5 1.57 1.16 ASW - 400

600-1000 650 4.63 2 1.16 0.69 0.25 1.88 2.34 1.68 ASW - 650

PG CLAMPS AL & BIMETALLIC OTHER RANGE OF CONNECTORS



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


ALUMINIUM DOUBLE BARREL CONNECTOR MATERIAL - ALUMINIUM FINISH - ELECTRO TINNED

Conductor Range (Al. or Cu.)

Stud Hole Size

Dimensions in Mm & (Inches) Type Product Code

Max Min J D F G H

350 KCMIL

6 STR 1 1/2 104.65 (4.12)

48.51 (1.91)

7.87 (0.31) 15.75 (0.62)

44.45 (1.75)

I AL2LA-350

600 KCMIL

4 STR 1/2 141.73 (5.58)

60.96 (2.40)

11.17 (0.44) 15.75 (0.62)

44.45 (1.75)

II AL2LA-600

800 KCMIL

350 KCMIL

1/2 147.82 (5.82)

81.03 (3.19)

12.70 (0.50) 15.75 (0.62)

44.45 (1.75)

II AL2LA-800

ALUMINIUM SINGLE BARREL CONNECTOR, ONE HOLE MOUNT MATERIAL - ALUMINIUM FINISH - ELECTRO TINNED

Conductor Range (Al. or Cu.)

Dimension in mm & (inches)

Max. Min. J D G Bolt Hole 'E' F Product Code

4 STR 14 AWG 27.00 (1.10) 12.70 (0.50) 5.95 (0.23) 1/4 2.40 (0.09) ALA - 4

2 STR 14 AWG 29.40 (1.15) 12.70 (0.50) 7.55 (0.29) 1/4 2.75 (0.10) ALA - 2

1/0 STR 14 AWG 37.10 (1.46) 15.90 (0.62) 11.10 (0.43) 1/4 4.70 (0.18) ALA - 10

2/0 STR 14 AWG 37.10 (1.46) 15.90 (0.62) 11.10 (0.43) 1/4 4.70 (0.18) ALA - 20

250 KCMIL 6 STR 50.60 (2.00) 21.75 (0.85) 12.75 (0.50) 5/16 6.40 (0.25) ALA - 250

300 KCMIL 6 STR 50.60 (2.00) 21.75 (0.85) 11.90 (0.46) 5/16 6.40 (0.25) ALA - 300

350 KCMIL 6 STR 57.15 (2.25) 28.60 (1.12) 12.70 (0.50) 3/8 6.40 (0.25) ALA - 350

500 KCMIL 4 STR 71.50 (2.81) 38.10 (1.50) 19.05 (0.75) 3/8 8.00 (0.31) ALA - 500

600 KCMIL 2 STR 81.00 (3.19) 38.10 (1.50) 20.60 (0.81) 3/8 11.10 (0.43) ALA - 600

800 KCMIL 300 KCMIL 85.70 (3.37) 44.50 (1.75) 22.20 (0.87) 5/8 12.70 (0.50) ALA - 800

1000 KCMIL 500 KCMIL 85.70 (3.37) 44.50 (1.750 22.20 (0.87) 5/8 12.70 (0.50) ALA - 1000



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


ALUMINIUM DOUBLE BARREL CONNECTOR, ONE HOLE MOUNT MATERIAL - ALUMINIUM FINISH - ELECTRO TINNED

Other types and sizes of Aluminium Mechanical lugs like etc. can be made on demand and / or customers specifications. 2 Hole Palm - 2 Hole Screw, 3 Hole Palm - 2 Hole Screw, 3 Hole Palm - 3 Hole Screw

PRE – INSULATED SLEEVES MJPTN Material - Aluminum alloy Features - Pre- Insulated Sleeve are designed for jointing insulated cables (include ABC cables). The sleeve is with full tension. The waterproof end cap can prevent water into the barrel. It is coloured differently to distinguish the cable sizes. It is marked with type, cable size, die size, inner cable length and number of crimping.

Sizes Cable size (mm2) Plastic Sleeve

Diameter C (mm)

Length (mm) Product Code

A B L

54.6 - 54.6 54.6 54.6 20 172.5 APIS - 54.6-54.6

54.6 - 70 54.6 70 20 172.5 APIS - 54.6 -70

70 - 70 70 70 20 172.5 APIS - 70-70

95 - 95 D 95 95 20 174.5 APIS - 95 - 95D

Conductor Range (Al. or Cu.) Dimension In Mm & (inches) Product Code Max. Min. J D G E F D1

1/0 STR 14 AWG 37.10 (1.46)

30.95 (1.22)

11.10 (0.43) 1/4 4.70

(0.18) - AL2A - 10

2/0 STR 14 AWG 37.10 (1.46)

31.75 (1.25)

10.70 (0.42) 1/4 4.70

(0.18) - AL2A - 20

250 KCMIL 6 STR 65.10 (2.56)

41.70 (1.64)

22.20 (0.87) 3/8 6.40

(0.25) 38.1

(1.50) AL2A - 250

350 KCMIL 6 STR 73.00 (2.87)

48.60 (1.91)

22.20 (0.87) 1/2 6.40

(0.25) 44.8

(1.76) AL2A - 350

600 KCMIL 2 STR 81.00 (3.19)

61.10 (2.40)

15.90 (0.62) 1/2 11.10 (0.43)

50.4 (1.98)

AL2A - 600

800 KCMIL 300 KCMIL 85.70 (3.37)

80.90 (3.18)

22.20 (0.87) 5/8 12.70 (0.50)

50.4 (1.98)

AL2A - 800

1000 KCMIL 500 KCMIL 85.70 (3.37)

80.90 (3.18)

22.20 (0.87) 5/8 12.70 (0.50)

- AL2A - 1000



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


FLEXIBLE CONNECTOR TINNED COPPER FLEXIBLE BRAIDS - CRIMPED WITH CONNECTORS / TERMINALS MATERIAL - E - COPPER FINISH - ELECTRO TINNED

Size mm2


J E1 E2 Current Rating AMP

(Crimped with Lugs)

(Crimped with Connectors)

4 50 6 6 50 AFT4 - 50 - 50 AFC4 -50 - 50

100 6 6 50 AFT - 100 - 50 AFC4 - 100 - 50

150 6 6 50 AFT4 - 150 – 150 AFC4 - 150 - 50

200 6 6 50 AFT4 - 200 – 50 AFC4 - 200 - 50

10 50 6 6 90 AFT10 - 50 -90 AFC10 - 50 - 90

100 6 6 90 AFT10 - 100 – 90 AHC10 - 50 – 90

150 6 6 90 AFT10 - 150 - 90 AFC10 - 150 - 90

200 6 6 90 AFT10 - 200 - 90 AFT10 - 200 - 90

16 100 8.5 8.5 125 AFT16 - 100 - 125 AFC16 - 100 - 125

150 8.5 8.5 125 AFT16 - 150 - 125 AFC16 - 150 - 125

200 8.5 8.5 125 AFT16 - 200 - 125 AFC16 - 200 - 125

250 8.5 8.5 125 AFT16 - 250 - 125 AFC16 - 250 - 125

300 8.5 8.5 125 AFT16 - 300 - 125 AFC16 - 300 – 125

25 100 10 10 160 AFT25 - 100 - 160 AFC25 - 100 – 160

150 10 10 160 AFT25 - 150 - 160 AFC25 - 150 - 160

200 10 10 160 AFT25 - 200 - 160 AFC25 - 200 - 160

250 10 10 160 AFT25 - 250 - 160 AFC25 - 250 - 160

300 10 10 160 AFT25 - 300 - 160 AFC25 - 300 - 160

30 100 10 10 180 AFT30 - 100 - 180 AFC30 - 100 - 180

150 10 10 180 AFT30 - 150 - 180 AFC30 - 150 - 180

200 10 10 180 AFT30 - 200 - 180 AFC30 - 200 - 180

250 10 10 180 AFT30 - 250 - 180 AFC30 - 250 - 180

300 10 10 180 AFT30 - 300 - 180 AFC30 - 300 - 180

35 100 10 10 210 AFT35 - 100 - 210 AFC35 - 100 - 210

150 10 10 210 AFT35 - 150 - 210 AFC35 - 150 - 210

200 10 10 210 AFT35 - 200 - 210 AFC35 - 200 - 210

250 10 10 210 AFT35 - 250 - 210 AFC35 - 250 - 210

300 10 10 210 AFT35 - 300 - 210 AFC35 - 300 - 210

50 100 12 12 250 AFT50 - 100 - 250 AFC50 - 100 - 250

150 12 12 250 AFT50 - 150 - 250 AFC50 - 150 - 250

200 12 12 250 AFT50 - 200 - 250 AFC50 - 200 - 250

250 12 12 250 AFT50 - 250 - 250 AFC50 - 250 - 250

300 12 12 250 AFT50 - 300 - 250 AFC56 - 300 - 250

Also available with other hole sizes, current rating, lengths etc, as per customer specifications.



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


RING, FORK, PIN, FLAT, CORD END, SNAP ON TERMINAL ENDS CABLE TERMINAL ENDS - (INSULATED & NON INSULATED) Ring Type, Pin Type, Flat Type, Fork Type. MATERIAL - E - Copper FINISH - Electro Tinned

Ring Type Pin Type Flat Type Fork Type

SNAP ON TERMINALS MATERIAL - E - COPPER FINISH - ELECTRO TINNED

CORD END FERRULES MATERIAL - E- Copper FINISH - Electro Tinned

COLOUR CODING OF INSULATION SLEEVE

SIZE COLOUR

1 - 5 RED

2 - 5 BLUE

4 - 6 YELLOW



Tel.: 00-91-22-24905100 / 6634 0200 / 6661 5090 - 91 Fax: 00-91-22-2490 5200 / 6634 1933


CRIMPING TOLS ACEPRESS CRIMPING TOOLS ACEPRESS G1 – 400 ACEPRESS HY - 400 (Gear Operated) (Hydraulic) Crimping Capacity : 50mm2 to 400mm2 (Al.) Dies : R - 11 to R – 18 50mm2 to 300mm2 (Cu.) Crimping Capacity : 50mm2 to 400mm2

ACEPRESS HYF – 400 ACEPRESS DCT - 500 (Hydraulic Foot Operated) (Dieless) Crimping Capacity : 50mm2 to 400mm2 Crimping Capacity : 16mm2 to 500mm2

ACEPRESS HY – 1000 ACEPRESS H - 95 (Hydraulic) (Dieless) Dies : R - 11 to R – 29 Crimping Capacity: Crimping Capacity : 50mm2 to 1000mm2 for Cu. & Al. crimping socket : 10mm2 to 95mm2

ACEPRESS H – 16 ACEPRESS F - 185 (Dieless) Dies : R-1 to R-13 Crimping Capacity : 1.5mm2 to 16mm2 Crimping Capacity : 10mm2 to 185mm2

TABLE OF CONTENT lugs.pdf · 4) Long Barrel Tinned Copper Cable Terminal Ends 5) Tubular...

Documents

Transcript of TABLE OF CONTENT lugs.pdf · 4) Long Barrel Tinned Copper Cable Terminal Ends 5) Tubular...