CABLE ACCESSORIES LUGS AND FERRULES · Complete T Cs at back of catalogue. LUGS AND FERRULES....
Transcript of CABLE ACCESSORIES LUGS AND FERRULES · Complete T Cs at back of catalogue. LUGS AND FERRULES....
2 VOLTEX CATALOGUEFor extended & complete range visit www.voltex.co.za. Minimum quantity orders may apply. Dimensions generally shown in mm and subject to technical change. Voltex codes and descriptions have been used above. Use Voltex K8 codes and product type for spec purposes. Refer to appendix for additional information, certification required and full technical specification from the supplier. All details provided are for indicative purposes only. Complete T & C's at back of catalogue.110 VOLTEX CATALOGUE
LUGS AND FERRULESCopper Lugs for Stranded Conductor Cable
Dimension1. The nominal area of the circular stranded
conductor is that of the nominal lug or ferrule size.2. For flexible cables the next highest lug or
ferrule size in relation to the area must be used.3. For compacted cable the heavy duty lugs and
ferrules must be used.
Certain compacted cables vary in nominal diameter and cable diameter must be matched to the lug or ferrule barrel inside diameter.
B A
C D
F
E
Nominal Lug Size
Typical Conductors
Stud Size
Nominal Dimensions Product Code
Circular Stranded
Flexible Stranded
(mm)
Barrel Spade
(mm2) (mm) (mm2) (mm)A B C D E F
I.D O.D Length Length Hole Pos. Width
1,5 3/0,81 1
3
1,9 3,8 7,0
9,0 4,5 7,0 H10283 H964 -
4 12,0 4,5 7,0 H10284 H966 H2551
5 12,0 4,5 8,0 H10285 H967 H2552
6 13,0 5,5 9,0 H10286 H968 H2553
2,5 3/1,04 1,5
3
2,4 3,9 7,3
8,5 4,5 7,0 H10287 H969 -
4 12,0 4,5 7,0 H10288 H971 H2554
5 12,0 4,5 9,0 H10289 H972 H2555
6 13,0 5,5 9,5 H10290 H973 H2556
8 15,0 7,5 12,0 H10291 H975 H2557
4 7/0,86 2,5
3
2,8 4,7
9,0 4,5 7,0 H10292 H976 -
4 12,0 4,5 7,0 H10293 H977 H2559
5 8,0 12,0 4,5 8,5 H10294 H978 H2560
6 13,0 5,5 10,0 H10295 H979 H2561
8 17,0 6,5 13,0 H10296 H980 H2562
10 11,0 19,0 7,5 14,0 H10297 H981 H2563
6 7/1,05 4
4
3,4 5,3
12,0 4,5 7,5 H10298 H2857 H2564
5 12,0 4,5 8,5 H10299 H982 H2565
6 8,5 13,0 5,5 9,5 H10300 H983 H2566
8 9,3 17,0 7,0 13,0 H10301 H984 H2567
10 11,0 19,0 7,5 15,0 H10302 H985 -
10 7/1,36 6
5 10,5 12,0 4,5 9,0 H10303 H987 H2568
6 10,5 13,0 6,0 10,0 H10304 H988 H2569
8 4,4 6,3 11,0 17,0 7,5 13,0 H10305 H989 H2570
10 11,0 19,0 7,5 15,0 H10306 H990 H2571
12 12,0 20,0 10,0 19,0 H10307 H991 H2572
16 7/1,72 10
5 13,0 5,5 10,5 H10308 H993 H2574
6 13,0 5,5 11,0 H10309 H994 H2575
8 5,5 7,6 12,0 18,0 7,5 13,0 H10310 H995 H2576
10 20,0 7,5 15,0 H10311 H996 H2577
12 25,0 10,5 18,0 H10312 H997 H2578
16 27,0 13,0 24,0 H10313 H998 H2579
25
18/1,35
16
6 16,0 6,0 14,0 H10314 H999 H2581
8 17,0 8,0 14,0 H10315 H1000 H2582
19/1,55
10 6,9 9,0 15,0 18,0 8,0 16,0 H10316 H1001 H2583
12 21,0 11,0 18,0 H10475 H1002 H2584
16 27,0 13,0 24,0 H10317 H338 -
Note: • Indent compression recommended for flexible stranded.• Confirm stock and brand availability with your local branch.
Components are tested to IEC 61238-1.
Items above with (-) in the codes column are available on special request.
CABLE ACCESSORIES
3VOLTEX CATALOGUEFor extended & complete range visit www.voltex.co.za. Minimum quantity orders may apply. Dimensions generally shown in mm and subject to technical change. Voltex codes and descriptions have been used above. Use Voltex K8 codes and product type for spec purposes. Refer to appendix for additional information, certification required and full technical specification from the supplier. All details provided are for indicative purposes only. Complete T & C's at back of catalogue. 111VOLTEX CATALOGUE
Note: • Indent compression recommended for flexible stranded.• Confirm stock and brand availability with your local branch.
Components are tested to IEC 61238-1.
LUGS AND FERRULES
Items above with (-) in the codes column are available on special request.
Copper Lugs for Stranded Conductor Cable
Nominal Lug Size
Typical Conductors
Stud Size
Nominal Dimensions Product Code
Circular Stranded
Flexible Stranded
(mm)
Barrel Spade
(mm2) (mm) (mm2) (mm)A B C D E F
I.D O.D Length Length Hole Pos. Width
35
18/1,59
25
6 15,0 18,0 8,0 16,0 H10318 H1003 H2585
8 15,0 18,0 9,0 16,0 H10319 H1004 H2586
19/1,55
10 8,2 10,7 15,0 18,0 9,0 16,0 H10320 H1005 H2587
12 15,0 22,0 10,0 18,0 - H1006 H2588
16 16,0 30,0 13,0 24,0 H10321 H1007 H2589
50 18/1,9 19/1,85
35
6 16,0 17,0 8,0 18,0 H10322 H1008 H2590
8 16,0 17,0 9,0 18,0 H10323 H1009 H2591
10 17,0 24,0 10,0 20,0 H10324 H1010 H2592
12 10,0 12,8 18,0 24,0 10,0 20,0 - H1012 H2593
16 18,0 30,0 13,0 26,0 H10325 H1013 H2594
20 18,0 30,0 13,0 26,0 H10326 H3266 -
70 18/2,2519/2,19 50
8 20,5 20,0 9,5 21,0 H10327 H1014 H2597
10 21,0 26,0 11,0 22,0 H10328 H1015 H2598
12 11,7 15,0 21,0 28,0 12,0 22,0 H10329 H1017 H2599
16 22,0 32,0 14,0 28,0 - H1018 H1342
20 22,0 34,0 15,0 30,0 H10330 H1175 H2600
95 36/1,8637/1,83 70
8 24,0 9,5 25,0 H10331 H1019 H2601
10 26,0 13,0 26,0 H10332 H1020 H2602
12 13,5 17,4 23,0 28,0 13,0 26,0 H10333 H1022 H2603
16 32,0 14,0 28,0 - H1023 H2604
20 36,0 16,0 30,0 H10334 H1176 H2605
120
36/2,08
70/95
10 26,0 12,0 27,0 H10335 H1024 H2606
12 28,0 12,0 28,0 H10336 H1025 H2607
37/2,0516 15,5 19,8 26,0 32,0 14,0 30,0 H10337 H1026 H2608
20 36,0 16,0 32,0 H10338 H2861 -
150
36/2,34
95/120
10 31,0 12,5 31,0 H10339 H1027 H2609
12 33,0 16,0 32,0 H10340 H1028 H2610
37/2,2916 17,0 22,0 27,0 35,0 16,0 32,0 H10341 H1029 H1343
20 36,0 16,0 32,0 H10342 H1030 H2661
185
36/2,59
120/150
10 29,0 12,5 34,0 H10343 H1031 H2611
12 31,0 16,0 34,0 H10344 H1032 H2612
37/2,5316 19,0 24,4 29,0 34,0 16,0 36,0 H10345 H1033 H2613
20 H10346 H1179 -
240
60/2,23
150/185
10 36,0 16,0 40,0 H10347 H1180 H2614
12 36,0 16,0 40,0 H10348 H1034 H2615
61/2,2616 21,5 27,7 33,0 38,0 20,0 40,0 H10349 H1884 H2616
20 42,0 20,0 40,0 H10350 H3267 H2617
300 60/2,5561/2,53 185/240
10 35,0 15,0 45,0 H10351 H3268 -
12 24,5 31,3 35,0 35,0 15,0 45,0 H10352 H1289 H2618
16 45,0 15,0 45,0 H10353 H367 -
20 45,0 16,0 45,0 H10354 H2863 H2619
400 91/2,39 240/300 16 27,5 35,6 41,047,0 49,0 - H4281 -
47,0 24,0 51,0 - H4280 H368
500 91/2,67 300/400 31,6 40,0 41,5 54,0 58,0 H369 H4282 -
630 127/2,54 400/500 34,5 44,6 53,0 65,0 64,0 H370 H4283 -
800 127/2,87 630 40,0 51,2 68,0 75,0 73,0 - H4284 -
1000 127/3,22 44,0 56,6 75,0 75,0 81,0 - H4285 -
CABLE ACCESSORIES
2 VOLTEX CATALOGUEFor extended & complete range visit www.voltex.co.za. Minimum quantity orders may apply. Dimensions generally shown in mm and subject to technical change. Voltex codes and descriptions have been used above. Use Voltex K8 codes and product type for spec purposes. Refer to appendix for additional information, certification required and full technical specification from the supplier. All details provided are for indicative purposes only. Complete T & C's at back of catalogue.112 VOLTEX CATALOGUE
LUGS AND FERRULESHeavy Duty Copper Lugs for Compacted XLPE Cable 6.35 - 11kV
Nominal Lug Size
SANS1411-1
Nominal Diameter
Over Cond.
Stud Size
Nominal Dimensions
Product Code
(mm)
Barrel Spade
(mm2) (mm)A B C D E F
I.D O.D Length Length Hole Pos. Width
35 7,0 10 7,30 10,50 16,0 24,0 11,0 19,0 H4130
50 8,2 10 8,75 12,30 20,0 24,0 11,0 19,0 H4131
70 9,7 10 10,40 14,60 21,0 27,0 14,0 20,0 H4132
95 11,4 10 12,10 17,00 24,0 28,0 14,0 24,0 H4133
120 12,6 12 14,00 19,10 26,0 28,0 14,0 26,0 H4134
150 14,6 12 15,25 21,30 31,0 37,0 18,0 30,0 H4135
185 15,9 12 17,00 23,70 34,0 40,0 19,0 33,0 H4136
240 16,3 12 20,00 27,10 34,0 41,0 19,0 37,0 H4137
300 20,8 * 21,63 30,50 38,0 48,0 20,0 42,5 H4138
400 23,6 * 24,50 34,64 51,0 49,0 23,5 48,0 H4139
500 26,2 * 28,50 38,90 51,0 52,0 25,0 54,0 H4140
630 30,3 * 33,00 45,00 53,0 65,0 28,0 64,0 H4141
B A
C D
F
ER1
Note: * Stud sizes can be made to customer requirements.
Components are tested to IEC 61238-1.
CABLE ACCESSORIES
3VOLTEX CATALOGUEFor extended & complete range visit www.voltex.co.za. Minimum quantity orders may apply. Dimensions generally shown in mm and subject to technical change. Voltex codes and descriptions have been used above. Use Voltex K8 codes and product type for spec purposes. Refer to appendix for additional information, certification required and full technical specification from the supplier. All details provided are for indicative purposes only. Complete T & C's at back of catalogue. 113VOLTEX CATALOGUE
LUGS AND FERRULESAluminium Stranded Circular Cable Lugs
Cable Stud SIzeA B C D E
Palm width Palm Thick
d1 d2 Product Code
(mm2) (mm) "F" "G"
25
8
65,00 28,00
8,40
17,00 12,0015,00 4,00
7,00 11,30
H4158
10 10,40 H4159
12 12,50 21,00 3,00 H4160
35
8
70,00 30,00
8,40
17,00 12,0017,50 4,00
8,30 12,90
H4161
10 10,40 H4162
12 12,50 21,00 3,50 H4163
50
10
70,0 32,00
10,40
17,00 12,0020,00 4,50
9,90 14,70
H4164
12 12,50 H4165
16 16,50 26,00 3,50 H4166
70
10
78,00 36,00
10,40
17,00 12,0023,00 5,00
11,70 17,00
H4167
12 12,50 H4168
16 16,50 26,00 4,50 H4169
95
10
85,00 39,00
10,40
18,00 12,00 27,50 5,50 13,70 19,70
H4170
12 12,50 H4171
16 16,50 H4172
120
10
89,00 45,00
10,40
17,00 12,00 31,00 6,50 15,30 22,20
H4173
12 12,50 H4174
16 16,50 H4175
150
12
100,00 48,00
12,50
20,00 16,00 34,50 7,00 17,20 24,70
H4176
16 16,50 H4177
20 20,50 H4178
185
12
108,00 53,00
12,50
20,00 16,00 38,00 7,50 19,00 27,30
H4179
16 16,50 H4180
20 20,50 H4181
240On request
118,00 57,00On request
22,00 18,00 43,50 8,50 21,80 31,00 H4182
300 132,00 62,00 25,00 20,00 49,00 9,50 24,90 35,00 H4183
Note:Components are tested to IEC 61238-1.
CABLE ACCESSORIES
2 VOLTEX CATALOGUEFor extended & complete range visit www.voltex.co.za. Minimum quantity orders may apply. Dimensions generally shown in mm and subject to technical change. Voltex codes and descriptions have been used above. Use Voltex K8 codes and product type for spec purposes. Refer to appendix for additional information, certification required and full technical specification from the supplier. All details provided are for indicative purposes only. Complete T & C's at back of catalogue.114 VOLTEX CATALOGUE
Note:Components are tested to IEC 61238-1.
LUGS AND FERRULESAluminium 3 Core Sector Shaped Cable Lugs
Cable Stud SIzeA B C D E
Palm width Palm Thick
d1 d2 Product Code
(mm2) (mm) "F" "G"
25
8
65,00 28,00
8,40
17,00 12,0015,00 4,00
5,20 8,73
H4184
10 10,40 H4185
12 12,50 21,00 3,00 H4186
35
8
70,00 30,00
8,40
17,00 12,0017,50 4,5
5,90 10,05
H4187
10 10,40 H4188
12 12,50 21,00 3,50 H4189
50
10
70,00 32,00
10,40
17,00 12,0022,00 4,50
7,25 11,85
H4190
12 12,50 H4191
16 16,50 26,00 3,50 H4192
70
10
78,00 36,00
10,40
17,00 12,0024,00 5,00
8,5 14,10
H4193
12 12,50 H4194
16 16,50 26,00 4,50 H4195
95
10
82,00 38,00
10,40
18,00 12,00 28,00 6,00 9,55 16,35
H4196
12 12,50 H4197
16 16,50 H4198
120
10
88,00 45,00
10,40
17,00 12,00 31,00 6,50 11,05 18,50
H4199
12 12,50 H4200
16 16,50 H4201
150
12
103,00 48,00
12,50
20,00 18,00 34,00 7,00 12,15 20,60
H4202
16 16,50 H4203
20 20,50 H4204
185
12
106,00 53,00
12,50
20,00 18,00 38,00 8,50 13,40 22,48
H4205
16 16,50 H4206
20 20,50 H4207
240On request
118,00 57,00On request
22,00 18,00 43,50 8,50 15,55 26,05 H4208
300 132,00 62,00 25,00 20,00 49,00 10,00 17,35 29,00 H4209
CABLE ACCESSORIES
3VOLTEX CATALOGUEFor extended & complete range visit www.voltex.co.za. Minimum quantity orders may apply. Dimensions generally shown in mm and subject to technical change. Voltex codes and descriptions have been used above. Use Voltex K8 codes and product type for spec purposes. Refer to appendix for additional information, certification required and full technical specification from the supplier. All details provided are for indicative purposes only. Complete T & C's at back of catalogue. 115VOLTEX CATALOGUE
LUGS AND FERRULESAluminium 4 Core Sector Shaped Cable Lugs
Cable Stud SIzeA B C D E
Palm width Palm Thick
d1 d2 Product Code
(mm2) (mm) "F" "G"
25
8
65,00 25,00
8,40
17,00 12,0015,00 4,00
5,80 7,88
H4210
10 10,40 H4211
12 12,50 21,00 3,00 H4212
35
8
70,00 30,00
8,40
17,00 12,0017,50 4,5
7,10 9,70
H4213
10 10,40 H4214
12 12,50 21,00 3,50 H4215
50
10
70,00 32,00
10,40
17,00 12,0020,00 4,50
8,35 10,95
H4216
12 12,50 H4217
16 16,50 26,00 3,00 H4218
70
10
78,00 36,00
10,40
17,00 12,0023,00 5,00
9,30 13,00
H4219
12 12,50 H4220
16 16,50 26,00 4,50 H4221
95
10
85,00 39,00
10,40
18,00 12,00 27,50 5,70 10,85 15,10
H353
12 12,50 H1021
16 16,50 H4222
120
10
89,00 45,00
10,40
17,00 12,00 31,00 6,50 12,05 17,00
H4223
12 12,50 H4224
16 16,50 H4225
150
12
100,00 48,00
12,50
20,00 16,00 34,50 7,20 13,80 18,80
H4226
16 16,50 H4227
20 20,50 H4228
185
12
108,00 53,00
12,50
20,00 16,00 38,50 8,00 15,25 21,00
H363
16 16,50 H4229
20 20,50 H4230
240On request
118,00 57,00On request
22,00 18,00 43,50 8,50 17,35 23,80 H4231
300 132,00 62,00 25,00 20,00 49,00 9,70 19,50 26,40 H4232
Note:Components are tested to IEC 61238-1.
CABLE ACCESSORIES
2 VOLTEX CATALOGUEFor extended & complete range visit www.voltex.co.za. Minimum quantity orders may apply. Dimensions generally shown in mm and subject to technical change. Voltex codes and descriptions have been used above. Use Voltex K8 codes and product type for spec purposes. Refer to appendix for additional information, certification required and full technical specification from the supplier. All details provided are for indicative purposes only. Complete T & C's at back of catalogue.116 VOLTEX CATALOGUE
LUGS AND FERRULES
Heavy Duty Copper Ferrules for Compacted XLPE Cable 6.35 - 11kV
Copper Ferrules for Stranded Conductor Cable
Nominal Sleeve Size
Nominal DimensionsTypical
Conductors Circular Stranded
Product Code
(mm)
I.D O.D Length
(mm2) A B C (mm)
1,5 1,9 3,6 13,0 3/0,81 H10367 H121 H2514
2,5 2,4 3,9 14,0 3/1,04 H10368 H124 H2515
4 2,8 4,7 16,0 7/0,86 H10369 H126 H2516
6 3,4 5,3 18,0 7/1,05 H10370 H129 H2517
10 4,4 6,3 20,0 7/1,36 H10371 H131 H2518
16 5,5 7,6 22,0 7/1,72 H10372 H133 H2519
25 6,9 9,0 25,0 18/1,35 H2174 H137 H2520
35 8,2 10,7 28,0 18/1,59 H2175 H141 H2521
50 10,0 12,8 31,0 18/1,90 H2176 H144 H2522
70 11,7 15,0 35,0 18/2,25 H23 H147 H2523
95 13,5 17,4 39,0 36/1,86 H2928 H151 H2524
120 15,5 19,8 43,0 36/2,08 H2177 H155 H2525
150 17,0 22,0 48,0 36/2,34 H2178 H159 H2526
185 19,0 24,4 54,0 36/2,59 H10373 H162 H2527
240 21,5 27,7 60,0 60/2,23 H10374 H165 H2528
300 24,5 31,3 67,0 60/2,55 H10375 H167 H2529
400 27,5 35,6 80,0 91/2,39 H10376 H3265 H2530
500 31,6 40,0 90,0 91/2,67 H10377 H4154 -
630 34,5 44,6 110,0 127/2,54 H10378 H4155 -
800 40,0 51,2 130,0 127/2,87 H10379 H4156 -
1000 44,0 56,6 154,0 127/3,22 H10380 H4157 -
Nominal Ferrule Size
Nominal Dimensions
Product Code(mm)
I.D O.D Length
(mm2) A B C
35 7,30 10,5 38 H4142
50 8,75 12,3 42 H4143
70 10,40 14,6 43 H4144
95 12,10 17,0 45 H4145
120 14,00 19,1 55 H4146
150 15,25 21,3 58 H4147
185 17,00 23,7 64 H4148
240 20,00 27,1 70 H4149
300 21,63 30,5 75 H4150
400 24,50 34,6 80 H4151
500 28,50 38,9 90 H4152
630 33,00 45,0 100 H4153
C
AB
Note:Components are tested to IEC 61238-1.
For items marked with a dash (-) please enquire at branch or reference website
CABLE ACCESSORIES
3VOLTEX CATALOGUEFor extended & complete range visit www.voltex.co.za. Minimum quantity orders may apply. Dimensions generally shown in mm and subject to technical change. Voltex codes and descriptions have been used above. Use Voltex K8 codes and product type for spec purposes. Refer to appendix for additional information, certification required and full technical specification from the supplier. All details provided are for indicative purposes only. Complete T & C's at back of catalogue. 117VOLTEX CATALOGUE
LUGS AND FERRULESAluminium Ferrules
Cable AStranded 3 Core 4 Core
D1 D2 Product Code H W Product
Code H W Product Code(mm2) (mm)
25 66 7,00 11,30 H135 5,20 8,73 H4286 5,8 7,88 H4296
35 70 8,30 12,90 H139 10,05 5,90 H4287 7,10 9,70 H4297
50 74 9,90 14,70 H142 11,85 7,25 H4288 8,35 10,95 H4298
70 78 11,70 17,00 H145 14,10 8,25 H4289 9,30 13,00 H4299
95 84 13,70 19,70 H149 16,35 9,55 H4290 10,85 15,10 H4300
120 91 15,30 22,20 H153 18,50 11,05 H4291 12,50 17,00 H4301
150 102 17,20 24,70 H157 20,60 12,15 H4292 13,80 18,80 H4302
185 108 19,00 27,30 H160 22,40 13,40 H4293 15,25 21,00 H4303
240 118 21,80 31,00 H163 26,05 15,55 H4294 17,35 23,80 H4304
300 130 24,90 35,00 H4233 29,00 17,35 H4295 19,50 26,40 H4305
Note:Components are tested to IEC 61238-1.
Stranded 3 Core 4 Core
A
CABLE ACCESSORIES