Siemens HiPath 4000 Release 3.0 using E1 QSIG to Cisco ... · • This is an Application Note for...
Transcript of Siemens HiPath 4000 Release 3.0 using E1 QSIG to Cisco ... · • This is an Application Note for...
© 2009 Cisco Systems, Inc. All rights reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 1 of 52 EDCS#789914 Rev#2 controlled by EDCS.
Application Note
Siemens HiPath 4000 Release 3.0 using E1 QSIG to Cisco Unified Communications Manager Express Release 7.1.0
July 27th 2009, Initial Version
Table of ContentsTable of ContentsTable of ContentsTable of Contents
Introduction..............................................................................................................................................................................................................2 Network Topology....................................................................................................................................................................................................3 Limitations................................................................................................................................................................................................................4 System Components.................................................................................................................................................................................................5
Hardware Requirements......................................................................................................................................................................................5 Software Requirements........................................................................................................................................................................................5
Features....................................................................................................................................................................................................................6 Features Supported..............................................................................................................................................................................................6 Features Not Supported.......................................................................................................................................................................................7
Configuration............................................................................................................................................................................................................8 Configuring the Siemens HiPath 4000 PBX......................................................................................................Error! Bookmark not defined. Configuration Menus and Commands for Hipath 4000......................................................................................Error! Bookmark not defined. Local Cisco Unified Communications Manager Express (Cisco 3825) Configuration......................................Error! Bookmark not defined. Cisco Unity Express Configuration...................................................................................................................Error! Bookmark not defined. Cisco Unified Communications Manager Express 2 (Cisco 3845) Configuration.............................................Error! Bookmark not defined.
Acronyms.................................................................................................................................................................Error! Bookmark not defined.
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 2 of 52
IntroductionIntroductionIntroductionIntroduction
• This is an Application Note for connectivity between a Siemens HiPath 4000 Release 3 PBX and Cisco Unified Communications Manager Express (CUCME) Release 7.1.0 using a Cisco 3825 voice gateway with QSIG protocol.
• The network topology diagram (Figure 1) shows the test setup for end-to-end interoperability with Cisco Unified Communications Manager Express Release 7.1.0 connected to the PBX via the 3825 E1 QSIG link. The CUCME 3825 IOS voice gateway has installed Cisco Unity Express 7.0.3 and is connected via H.323 to a second CUCME 3845 IOS voice gateway. The two gateways are running Cisco Unified Communications Manager Express 7.1.0. Cisco Unified IP phones (models 7960 and 7970) were connected to the 2 Cisco Unified Communications Manager Express gateways via SIP and SCCP, as per figure 1. A HWIC and VWIC-2MFT-E1 is used for the E1 QSIG interface. Calls were made to test basic call, caller ID, call conference, call transfer, call forward, reroute and voicemail features.
• The inclusion of Cisco SIP phones in this application note is for reference only. CME 7.1.0 supports SIP end-points with limited number of features.
• This Application Note uses the 3825 and 3845 voice gateways. However, the use of other Cisco voice gateways is also an option since Cisco Unified Communications Manager Express features do not depend on the Cisco IOS platform. The listed gateway families, below, can run Cisco Unified CallManager Express, but each have different IP phone support capability. Please check the product specifications to ensure you are obtaining the proper device to support your VoIP deployment.
Cisco 1861 Integrated Services Router (Unity: ISE-CUE) Cisco 2800 Integrated Services Router Cisco 2801 Integrated Services Router (Unity on Cisco 2801: NM-CUE or AIM-CUE) Cisco 3700 Series Multiservice Access Routers Cisco 3800 Integrated Services Router
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 3 of 52
Network TopologyNetwork TopologyNetwork TopologyNetwork Topology
Figure 1. Network Topology or Test Setup – basic calls configuration.
Phone A
x5002
Phone B
x5003
Phone F
1650-364-6325
Cisco CME 7.1.0 (c3825)
Cisco CUE 7.0.3 (AIM-CUE)ISDN Type:
E1-QSIG
PBX: Siemens HiPath 4000
Release 3.0
PSTN
Dial-4XXX
Dial-6XXX
Phone C1
x4003
Phone D1
x4004
Phone C2
x4001
Phone D2
x4002
Phone G1
x4005
Phone G2
x4006
Cisco CME 7.1.0 (c3845)
Ethernet
Cisco 7960 SCCP
Phones
Cisco 7960/7970 SIP
Phones
Cisco 7960 SCCP
Phones
Dial Plans
5XXX
91650-XXXXXXX
To PBX Ext.
To PSTN
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 4 of 52
LimitationsLimitationsLimitationsLimitations
Basic Calls
• Cisco Unified Communications Manager Express does not support overlap sending. It does support overlap receiving.
• Calling Name Restriction is not supported for calls originating from from Cisco Unified Communications Manager Express end-points.
• Connected Name and Number restriction is not supported by Cisco Unified Communications Manager Express.
Call Transfers
• Consulation, Early Attended and blind transfer (local): Cisco Unified Communication Manager Express does not update end-points with the information of external changed extension also, it does not update PBX with locally ’transferred to’ extension.
• For all supervised and early-attended Network/External call transfers, the original calling name and number are not displayed on the final destination. The limitation is due to the CME not supporting the QSIG operation”CallTransferComplete” carried in the Q931 FACILITY message for name/number updating
• Call fails for all supervised and early-attended network/External SIP calling SCCP transfering to PBX or SCCP calling SIP phone transfering to PBX.
• Calls fail during network/External blind transfer when PBX intiates the call and SCCP/SIP phone transfers back to PBX.
Call Forwards
• For call forward CFU, CFB and CFNR by join(Local), the forwarding called name is not updated on the final destination when the final destination is either SIP/SCCP.
• For call forward CFU, CFB and CFNR by join (Local and Network/External), final destination connected number is not updated on originating extension.
• For call forward CFU, CFB and CFNR by join or reroute (Network/External), the forwarding called name is not updated on the final destination.
• For call forward CFU CFB and CFNR by join (Network/External), the final destination connected name not updated at originating etenstion when the intiator and the final destination is a SIP phone. This is a CME to SIP phone limitation.
• Forwarded calls originated from PBX (CFU, CFB and CFNR by join) extension to a external Cisco Unified Communications Manager Express SCCP extension, and forwarded to PBX, final destination connected name is not updated on Originating phone.
• Forwarded calls originated from PBX (CFU, CFB and CFNR by join) extension to a external Cisco Unified Communications Manager Express SCCP extension and forwarded to local Cisco Unified Communications Manager Express SIP extension, forwarding number is not displayed on final destination.
• For call forward CFU CFB and CFNR by reroute (Network/External), the final destination connected name and number, and forwarding destination connected name and number are not updated at originating extenstion and final destinations respectively when the intiator and the final destination is a SIP phone.
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 5 of 52
System ComponentsSystem ComponentsSystem ComponentsSystem Components
Hardware Requirements
• Cisco 3825 voice gateway
• NM-HDV
• VWIC-2MFT-E1
• AIM-CUE
• Cisco 3845 IOS voice gateway
• (5) Cisco Unified IP phone 7960s
• (1) Cisco Unified IP phone 7970
• (1) Siemens HiPath 4000
• DIU-N2
Software Requirements
• Cisco Unified Communications Manager Express Release 7.1.0
• Cisco Unity Express Release 7.0.3
• Cisco IOS Software, 3800 Software (C3845-IPVOICE-M), Version 12.4(22)YB1
• Cisco IOS Software, 2801 Software (C2801-IPVOICE-M), Version 12.4(22)YB1
C1, D1, G1, G2 – 7960 – SCCP
• Cisco7960 IP phone version 8.0(10.0)
• Cisco 7960 IP phone app load P00308001000
• Cisco 7960 IP phone boot load PC0303010100
C2 – 7970 - SIP
• Cisco7970 load file SIP70.8-4-2S
• Cisco 7970 IP phone app load jar70sip.8-4-1-23.sbn
• Cisco 7970 IP phone boot load 7970_020706_cert.bin
D2 – 7960 – SIP
• Cisco7960 IP DSP load file: 4.0(5.0)[A0]
• Cisco 7960 IP phone app load ID: P0S3-08-11-00
• Cisco 7960 IP phone boot load ID: PC030301
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 6 of 52
FeaturesFeaturesFeaturesFeatures
This section lists supported and unsupported features.
Features Supported
• Basic Call, ENBLOC and Overlap sending (From PBX to Cisco Unified Communications Manager Express only. See Limitations section for details.)
• CLIP-Calling Line (Number) Identification Presentation and CNIP-Calling Name Identification Presentation on Basic Calls
• CLIR-Calling Line (Number) Identification Restriction and CNIR-Calling Name Identification Restriction on Basic Calls (From PBX to Cisco Unified Communications Manager Express only. See Limitations section for details.)
• COLP-Connected Line (Number) Identification Presentation.
• Alerting Name on Basic Calls
• Tandem PSTN call
• Call transfer Consultation, Early Attended and Blind Transfer - Local (See Limitations section for details.)
• Call transfer Consultation, Early Attended and Blind Transfer – Network/External (See Limitations section for details.)
• Call Forward by forward unconditional, busy and No Reply by Join (forward switch) – Local and Network/External (See Limitations section for details.)
• Call Forward unconditional, busy and no reply by Reroute – Network/External (See Limitations section for details.)
• MWI
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 7 of 52
Features Not Supported
• Basic Call, Overlap sending originating from Cisco Unified Communications Manager Express IP phone to PBX
• CNIR-Calling Name Identification Restriction from Cisco Unified Communications Manager Express to PBX
• COLR- Connected Line (Number) Identification Restriction
• CONR- Connected Name Identification Restriction
• Name and Number updates on transferred calls
• CLIP-Calling Line (Number) Identification Presentation on Forwarded Calls to a PBX station.
• Consultation and Early Attended Call transfer (Network/External), call intiated from SIP/SCCP and trasfered to PBX by SCCP/SIP.
• Blind transfer (Network/External): Call initiated from PBX, SIP/SCCP transfering back to PBX.
• Connected Name and Number updates on forwarded calls
• Call Forward by Reroute for QSIG ”trombone” from a Cisco Unified Communications Manager Express SIP extension
• Call Forward by Reroute during a call originated by overlap sending/receiving
• Call Completion to Busy Subscriber (Call Back when Free)
• Call Completion on No Reply (Call Back Next Used)
• Path Replacement for Call Transfer by Join
• Path Replacement for Trombone Connection (accomplished by consultation transfer)
• Path Replacement for Call Diversion by Forward Switch
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 8 of 52
ConfigurationConfigurationConfigurationConfiguration
Configuring the Siemens HiPath 4000 PBX
1. Add the new access code to Dialing Plans using WABE + LDPLN.
2. Enbloc sending
3. Access code for Overlap sending
4. Add the new trunk board using BCSU.
5. Configure Class of Trunk using COT.
6. Configure Class of Parameter for device handler using COP.
7. Configure Class of Service using COSSU.
8. Add the new trunk group access code using BUEND.
9. Configure trunk using TDCSU.
10. Configure Reference Clock using REFTA.
11. Configure trunk Least Cost Routing using LDAT + RICHT
12. Configure station for Name and Number restrictions
13. Configure LCR Out-dial Rules using LODR.
14. Enable In-Band DTMF signaling for the Digital Stations using SBCSU.
15. Configure Digital Station for MWI application.
16. Configure Message Center’s Service Access Number for MWI application
17. Software release information
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 9 of 52
Configuration Menus and Commands for Hipath 4000
DPLN
DISPLAY-WABE:TYPE=GEN; H500: AMO WABE STARTED ------------------------------------------------- ----------------------------- | DIGIT INTERPRETATION VALID FO R ALL DIAL PLANS | ------------------------------------------------- ----------------------------- | | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT | | CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO | | |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE | ------------------------------------------------- ----------------------------- | 0 |. .**** ..*** **... ..... .*| CO | R | | 001 - 010 |* ..... ..... ..... ..... ..| NETRTE | | | 111 |. .**** ***** **... ..... .*| TIE | | | 1150 - 1159 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 111 | | | | |DNNO 0- 0-111 | | | | |PDNNO 0- 0-111 | | 12 - 15 |. .**** ***** **... ..... .*| TIE | | | 21 |. ..... ..... ..... ....* ..| KNOVRKY | | | 22 |. ..... ..... ..... ....* ..| DNDKY | | | 222 |. .**** ***** **... ..... .*| TIE | | | 23 |. ..... ..... ..... ....* ..| FWDKY | | | 24 |. ..... ..... ..... ....* ..| MBKY | | | 25 |. ..... ..... ..... ....* ..| MSGRKY | | | 26 |. ..... ..... ..... ....* ..| DAKY | | | 26 |. ....* ..... ..... ..... ..| DFFWDVCE | | | 27 |. ..... ..... ..... ....* ..| DSSKY | | ------------------------------------------------- ----------------------------- | DIGIT INTERPRETATION VALID FO R ALL DIAL PLANS | ------------------------------------------------- ----------------------------- | | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT | | CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO | | |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE | ------------------------------------------------- ----------------------------- | 27 |. ....* ..... ....* ..... ..| AFWDVCE | | | 28 |. ..... ..... ..... ....* ..| VCRKY | | | 28 |. ....* ..... ..... ..... ..| DFWDVCE | | | 29 |. ..... ..... ..... ....* ..| VCKY | | | 30 |. ..... ..... ..... ....* ..| CONFKY | | | 3000 - 3010 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 30 | | | | |DNNO 0- 0- 30 | | | | |PDNNO 0- 0-222 | | 3011 - 3020 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 31 | | | | |DNNO 0- 0- 31 | | | | |PDNNO 0- 0- 31 | | 3021 - 3030 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 32 | | | | |DNNO 0- 0- 32 | | | | |PDNNO 0- 0- 32 | ------------------------------------------------- ----------------------------- | DIGIT INTERPRETATION VALID FO R ALL DIAL PLANS | ------------------------------------------------- ----------------------------- | | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT | | CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO | | |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE | ------------------------------------------------- ----------------------------- | 3031 - 3040 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 33 | | | | |DNNO 0- 0- 33 | | | | |PDNNO 0- 0- 33 | | 3041 - 3050 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 35 | | | | |DNNO 0- 0- 35 | | | | |PDNNO 0- 0- 35 | | 31 |. ..... ..... ..... ....* ..| NAMEKY | |
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 10 of 52
| 32 |. ..... ..... ..... ....* ..| PARKKY | | | 33 |. ..... ..... ..... ....* ..| CCKY | | | 34 |. ..... ..... ..... ....* ..| HTKY | | | 35 |. ..... ..... ..... ....* ..| STKY | | | 36 - 37 |. .**** ..*** **... ..... .*| CO | | | 38 |. ..... ..... ..... ....* ..| TIMEKY | | | 39 |. .**** ***** **... ..... .*| TIE | | ------------------------------------------------- ----------------------------- | DIGIT INTERPRETATION VALID FO R ALL DIAL PLANS | ------------------------------------------------- ----------------------------- | | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT | | CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO | | |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE | ------------------------------------------------- ----------------------------- | 4000 - 4050 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 111 | | | | |DNNO 0- 0-111 | | | | |PDNNO 0- 0-111 | | 4051 - 4566 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 222 | | | | |DNNO 0- 0-222 | | | | |PDNNO 0- 0-222 | | 4567 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 34 | | | | |DNNO 0- 0- 34 | | | | |PDNNO 0- 0-200 | | 4568 - 4599 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 222 | | | | |DNNO 0- 0-222 | | | | |PDNNO 0- 0-222 | ------------------------------------------------- ----------------------------- | DIGIT INTERPRETATION VALID FO R ALL DIAL PLANS | ------------------------------------------------- ----------------------------- | | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT | | CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO | | |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE | ------------------------------------------------- ----------------------------- | 4600 - 4650 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 80 | | | | |DNNO 0- 0- 80 | | | | |PDNNO 0- 0- 80 | | 4651 - 4999 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 222 | | | | |DNNO 0- 0-222 | | | | |PDNNO 0- 0-222 | | 5000 - 5009 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 0 | | | | |DNNO 0- 0-555*| | 5010 - 5020 |. .**** ***** **... ..... .*| STN | R | | | | |DESTNO 0 | | | | |DNNO 0- 0-555*| | 5021 - 5040 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 0 | | | | |DNNO 0- 0-555*| ------------------------------------------------- ----------------------------- | DIGIT INTERPRETATION VALID FO R ALL DIAL PLANS | ------------------------------------------------- ----------------------------- | | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT | | CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO | | |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE | ------------------------------------------------- ----------------------------- | 5100 - 5109 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 0 | | | | |DNNO 0- 0-555*| | 5500 - 5501 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 56 | | | | |DNNO 0- 0-560 | | | | |PDNNO 0- 0-560 | | 555 |. .**** ***** **... ..... .*| OWNNODE | | | 560 |. .**** ***** **... ..... .*| TIE | | | 570 |. .**** ***** **... ..... .*| TIE | |
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 11 of 52
| 578 |. .**** ***** **... ..... .*| TIE | | | 59 |. .**** ***** **... ..... .*| TIE | | | 6000 - 6009 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 111 | | | | |DNNO 0- 0-111 | | | | |PDNNO 0- 0-111 | ------------------------------------------------- ----------------------------- | DIGIT INTERPRETATION VALID FO R ALL DIAL PLANS | ------------------------------------------------- ----------------------------- | | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT | | CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO | | |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE | ------------------------------------------------- ----------------------------- | 6123 |. .**** ***** **... ..... .*| STN | R | | | | |DESTNO 0 | | | | |DNNO 0- 0-555*| | 62 |. ....* ..... ....* ..... ..| AFFWDVCE | | | 7000 - 7002 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 56 | | | | |DNNO 0- 0-560 | | | | |PDNNO 0- 0-560 | | 8000 - 8050 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 222 | | | | |DNNO 0- 0-222 | | | | |PDNNO 0- 0-222 | | 8060 |. .**** ***** **... ..... .*| TIE | | | 8070 |. .**** ***** **... ..... .*| TIE | | | 8080 |. .**** ***** **... ..... .*| TIE | | | 8088 |. .**** ***** **... ..... .*| TIE | | ------------------------------------------------- ----------------------------- | DIGIT INTERPRETATION VALID FO R ALL DIAL PLANS | ------------------------------------------------- ----------------------------- | | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT | | CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO | | |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE | ------------------------------------------------- ----------------------------- | 8100 - 8109 |. .**** ***** **... ..... .*| STN | | | | | |DESTNO 32 | | | | |DNNO 0- 0- 32 | | | | |PDNNO 0- 0- 32 | | 8200 - 8209 |. .**** ..**. ..... ..... ..| PARK | | | 83 |. .**** ..*** **... ..... .*| SPDC1 | | | 84 |. .**** ..*** **... ..... .*| SPDC2 | | | 88 |. ..... ..*.. ..... ..... .*| SCONSI | R | | 89 |. ..... ...*. ..... ..... ..| SCONSCO | R | | 9 |. .**** ***** **... ..... .*| TIE | | | *13 |. ....* ..... ..... ..... ..| AHTVCE | | | *15 |. *.... ..**. ..... ..... .*| SPLIT | | | *16 |. ....* ..... ....* ..... ..| AREM | | | *17 |. *.... ..**. ..... ..... ..| TRACE | | | *18 |. ....* ..... ..... ..... ..| ACOSX | | | *19 |. *.... ..... ..... ..... ..| KNOVR | | | *20 |. ....* ..... ..... ..... ..| ADND | | ------------------------------------------------- ----------------------------- | DIGIT INTERPRETATION VALID FO R ALL DIAL PLANS | ------------------------------------------------- ----------------------------- | | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT | | CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO | | |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE | ------------------------------------------------- ----------------------------- | *25 |. ....* ..... ..... ..... ..| FWDTERM | | | *26 |. ....* ..... ..... ..... ..| DFFWDVCE | | | *27 |. ....* ..... ....* ..... ..| AFWDVCE | | | *28 |. ....* ..... ..... ..... ..| DFWDVCE | | | *29 |. ....* ..... ....* ..... ..| AFFWDVCE | | | *91 |. ....* ....* ..... ..... ..| MBOFF | | | #31 |. ....* ..... ....* ..... ..| AFFWDVCE | | | #91 |. ....* ....* ..... ..... ..| MBON | | | ##27 |. ***** ..**. ..... ..... ..| MWACT | | | ##28 |. ....* ..... ..... ..... ..| MWANS | | | ##29 |. ....* ..... ..... ..... ..| MWCAN | |
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 12 of 52
| ##30 |. ***** ****. ..*** .**** ..| MWCANORI | | | ##40 - ##49 |. .**** ..**. ..... ..... ..| PARK | | ------------------------------------------------- ----------------------------- AMO-WABE -111 DIALLING PLANS, FEATURE ACCESS CODES DISPLAY COMPLETED;
Enbloc Sending Dial Plan, DPLN
DISPLAY-LDPLN:TYPE=LDP,LDPNO=2; H500: AMO LDPLN STARTED +--------------+-------------------------------- -----------------+ | | | | DIPLNUM: 0| | | LDPNO : 2| LDP : 111-X | | | SPC : 22 | | | FDSFIELD : 0 SDSFIELD : 0 P INDP : N | +------+-------+-------------------------------- -----------------+ | DPLN | LROUTE| LAUTH | |------+-------+-------------------------------- -----------------+ | 0 | 1 | 1 | | 1 | 1 | 1 | | 2 | 1 | 1 | | 3 | 1 | 1 | | 4 | 1 | 1 | | 5 | 1 | 1 | | 6 | 1 | 1 | | 7 | 1 | 1 | | 8 | 1 | 1 | | 9 | 1 | 1 | | 10 | 1 | 1 | | 11 | 1 | 1 | | 12 | 1 | 1 | | 13 | 1 | 1 | | 14 | 1 | 1 | | 15 | 1 | 1 | +------+-------+-------------------------------- -----------------+ AMO-LDPLN-111 ADMINISTRATION LCR DIALPLAN DISPLAY COMPLETED;
Access code for Overlap Sending Dial Plan, DPLN
DISPLAY-LDPLN:TYPE=LDP,LDPNO=13; H500: AMO LDPLN STARTED +--------------+-------------------------------- -----------------+ | | | | DIPLNUM: 0| | | LDPNO : 13| LDP : 59-X | | | SPC : 22 | | | FDSFIELD : 1 SDSFIELD : 2 P INDP : N | +------+-------+-------------------------------- -----------------+ | DPLN | LROUTE| LAUTH | |------+-------+-------------------------------- -----------------+ | 0 | 27 | 1 | | 1 | 27 | 1 | | 2 | 27 | 1 | | 3 | 27 | 1 | | 4 | 27 | 1 | | 5 | 27 | 1 | | 6 | 27 | 1 | | 7 | 27 | 1 | | 8 | 27 | 1 | | 9 | 27 | 1 | | 10 | 27 | 1 | | 11 | 27 | 1 |
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 13 of 52
| 12 | 27 | 1 | | 13 | 27 | 1 | | 14 | 27 | 1 | | 15 | 27 | 1 | +------+-------+-------------------------------- -----------------+ AMO-LDPLN-111 ADMINISTRATION LCR DIALPLAN DISPLAY COMPLETED;
BCSU
PRI Board DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=3,SLOT=25; H500: AMO BCSU STARTED ADDRESS : LTG 1 LTU 3 SOURCE GROUP 1 -----+-----------+---------+---+---+-+------------+ -----+--------+------------+ | ASSIGNED | MODULE |FCT|HWY| | INSERTED | | | MODULE | PEN | MODULE | TYPE |ID |BDL| | MODULE | STATE| HW-INFO| STATUS | -----+-----------+---------+---+---+-+------------+ -----+--------+------------+ 25 | Q2196-X DIU-N2 1 A | | Q2196-X | 1 | -06 - | READY | AMO-BCSU -111 BOARD CONFIGURATION, SWITCHING UNIT DISPLAY COMPLETED;
Class of Trunk, COT
DIS-COT:22; H500: AMO COT STARTED COT: 22 INFO: DEVICE: INDEP SOURCE: DB PARAMETER: PRIORITY FOR AC WILL BE DETERMINED FROM MES SAGE PRI RECALL IF USER HANGS UP IN CONSULTATION CAL L RCL TRUNK CALL TRANSFER XFER TRUNK SIGNALING ANSWER ANS CHANGEOVER FROM HOLD TO RING TONE CHRT KNOCKING OVERRIDE POSSIBLE KNOR CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN DON'T RELEASE CALL TO BUSY HUNT GROUP BSHT CONNECTION TO ROUTE OPTIMIZATION NODE ROPT TSC-SIGNALING FOR NETWORKWIDE FEATURES (MAN DATORY) TSCS INCOMING CDR BY ZONE OR FROM LINE ICZL AOC PER CALL (AUTOMATICAL OR ON REQUEST), M AND. CORNET-NQ AOCC LINE WITH IMPLICIT NUMBERS LINO NO TONE NTON AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESS ING DISPLAY COMPLETED; For Call Forwarding by Reroute need to add FNAN and FWDN to COT22 For Path Replacement need to add ROPT to COT 22 on the Hipath 4000. CHANGE-COT:COTNO=22,COTTYPE=COTADD,PAR=FNAN&FWDN&ROPT; H500: AMO COT STARTED H07: CHANGED COT STILL LINKED WITH FOLLOWING TRUNKS : COT TRUNK BCGR DEVICE ----------------------------------- 22 1- 3- 55- 0 1 CDGCONN 1- 3- 55- 1 1 CDGCONN 1- 3- 25- 0 1 S2CONN
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 14 of 52
1- 3- 25- 1 1 S2CONN ----------------------------------- H06: COT 22 CHANGED AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESS ING CHANGE COMPLETED; DISPLAY-COT:COTNO=22; H500: AMO COT STARTED COT: 22 INFO: DEVICE: INDEP SOURCE: DB PARAMETER: PRIORITY FOR AC WILL BE DETERMINED FROM MES SAGE PRI RECALL IF USER HANGS UP IN CONSULTATION CAL L RCL TRUNK CALL TRANSFER XFER TRUNK SIGNALING ANSWER ANS CHANGEOVER FROM HOLD TO RING TONE CHRT KNOCKING OVERRIDE POSSIBLE KNOR CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN NETWORKWIDE CALL FORWARDING PERMITTED FWDN NETWORKWIDE FORWARDING NO-ANSWER FNAN DON'T RELEASE CALL TO BUSY HUNT GROUP BSHT CONNECTION TO ROUTE OPTIMIZATION NODE ROPT TSC-SIGNALING FOR NETWORKWIDE FEATURES (MAN DATORY) TSCS INCOMING CDR BY ZONE OR FROM LINE ICZL AOC PER CALL (AUTOMATICAL OR ON REQUEST), M AND. CORNET-NQ AOCC LINE WITH IMPLICIT NUMBERS LINO NO TONE NTON AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESS ING DISPLAY COMPLETED;
Class of Parameter for Device Handler, COP
DISPLAY-COP:COPNO=21; H500: AMO COP STARTED COP: 21 INFO: DEVICE: INDEP SOURCE: DB PARAMETER: LINE WITH END-OF-DIAL EOD SPECIAL MODE SFRM CODE CALLING RELEASE AFTER EVERY TASK CCR REGISTRATION OF LAYER 3 ADVISORIES L3AR CO TRUNK ACCESS: TRUNK ACCESS TA TOLL ACCESS: TRUNK ACCESS TA AMO-COP -111 CLASS OF PARAMETER FOR DEVICE H ANDLER DISPLAY COMPLETED;
Class of Service, COSSU
DISPLAY-COSSU:TYPE=COS,COS=32; H500: AMO COSSU STARTED +------+-----------------+---------------+------ -----------+ | COS | VOICE | FAX | DTE | +------+-----------------+---------------+------ -----------+ | 32 |> | | | TA | NOCO | TA |
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 15 of 52
| | TNOTCR | NOTIE | T NOTCR | | | | | BASIC | | | | | MSN | | | | | C DRINT | | | | | M ULTRA | | | | | | +------+-----------------+---------------+------ -----------+ AMO-COSSU-111 CLASSES OF SERVICE DISPLAY COMPLETED; DISPLAY-COSSU:TYPE=LCOSV,LCOSV=1; H500: AMO COSSU STARTED +----+------------------------------------------ ----------------------+-----+ |LCOS| LAUTH | | | V | 1 2 3 4 5 6 | | | |123456789012345678901234567890123456789012 3456789012345678901234|COPIN| | |>SERVICE INFORMATION | NUM | +----+----+----|----+----|----+----|----+----|-- --+----|----+----|----+-----+ | 1|X......................................... ......................| 0 | | |>LCR ATTENDANT FOR VOICE | +----+------------------------------------------ ----------------------+-----+ AMO-COSSU-111 CLASSES OF SERVICE DISPLAY COMPLETED;
Trunk Group Access Code, BUEND
DISPLAY-BUEND:TGRP=27,FORMAT=L; H500: AMO BUEND STARTED +------------------------------- FORMAT = L ------- ----------------------------+ | TGRP NUMBER : 27 TGRP NAME : PRI ECMA 4 MAXIMUM NO. : 30 | | CHARCON : NEUTRAL | | SUBGROUP NO.: 13 DEVICE TYPE : S2CONN TRACENO : 0 | | SEARCH MODE : CIRCULAR ACD THRESHOLD : * | | NUMBER OF ASSOCIATED ROUTES : 4 PRIORITY : 2 | | TDDRFLAG : ON TDDRTHRESHOLD: 3 SOURCEGROUPIDX : 1 | | GDTRRULE : 0 ACDPMGRP : 0 | | THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEE N ALLOCATED: | +-------------------------------------------------- ----------------------------+ | 1- 3- 25-1 1 | 1- 3- 25-1 2 | 1- 3- 25-1 3 | | 1- 3- 25-1 4 | 1- 3- 25-1 5 | 1- 3- 25-1 6 | | 1- 3- 25-1 7 | 1- 3- 25-1 8 | 1- 3- 25-1 9 | | 1- 3- 25-1 10 | 1- 3- 25-1 1 1 | 1- 3- 25-1 12 | | 1- 3- 25-1 13 | 1- 3- 25-1 1 4 | 1- 3- 25-1 15 | | 1- 3- 25-1 16 | 1- 3- 25-1 1 7 | 1- 3- 25-1 18 | | 1- 3- 25-1 19 | 1- 3- 25-1 2 0 | 1- 3- 25-1 21 | | 1- 3- 25-1 22 | 1- 3- 25-1 2 3 | 1- 3- 25-1 24 | | 1- 3- 25-1 25 | 1- 3- 25-1 2 6 | 1- 3- 25-1 27 | | 1- 3- 25-1 28 | 1- 3- 25-1 2 9 | 1- 3- 25-1 30 | +-------------------------------------------------- ----------------------------+ AMO-BUEND-111 TRUNK GROUP DISPLAY COMPLETED;
Trunk Configuration, TDCSU
For Master-side Configuration DISPLAY-TDCSU:1-3-25-1; H500: AMO TDCSU STARTED +------------------------ DIGITAL TRUNK (FORMAT=L ) -------------------------+ | DEV = S2CONN PEN = 1-03-025-1 TGRP = 27 | |------------------------------------------------ ---------------------------|
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 16 of 52
| PROTVAR = PSS1V2 INS = Y SRCHMODE = CIR | | COTNO = 22 COPNO = 21 DPLN = 0 | | ITR = 1 COS = 32 LCOSV = 1 | | LCOSD = 1 CCT = PRI ECMA 4 DESTNO = 111 | | SEGMENT = 1 DEDSCC = DEDSVC = NONE | | FACILITY = DITIDX = SRTIDX = | | TRTBL = GDTR SIDANI = N ATNTYP = TIE | | CBMATTR = NONE NWMUXTIM = 10 TCHARG = N | | SUPPRESS = 0 DGTPR = CHIMAP = N | | ISDNIP = ISDNNP = | | PNPL2P = PNPL1P = 408 PNPAC = | | TRACOUNT = 31 SATCOUNT = MANY NNO = 111 | | ALARMNO = 0 FIDX = 1 CARRIER = 1 | | ZONE = EMPTY COTX = 22 FWDX = 10 | | DOMTYPE = DOMAINNO = TPROFNO = | | INIGHT = CCHDL = | | UUSCCX = 16 UUSCCY = 8 FNIDX = 1 | | CLASSMRK = EC & G711 & G729OPT SRCGRP = | | TCCID = | |------------------------------------------------ ---------------------------| | BCNEG = N BCGR = 1 LWPAR = 1 | | LWPP = 0 LWLT = 0 LWPS = 0 | | LWR1 = 0 LWR2 = 0 | | DMCALLWD = DMCSEC = VNNO = | | SVCDOM = | | BCHAN = 1 && 30 | | | +------------------------------------------------ ---------------------------+ AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30 AMO-TDCSU-111 DIGITAL TRUNKS DISPLAY COMPLETED; DISPLAY-LWPAR:FORMAT=L,BLNO=1,TYPE=DIUS2; H500: AMO LWPAR STARTED +----------------------------------------------- ------------------------+ | LOADWARE PARAMETERS CIRCUIT TYPE: DIUS2 S OURCE:DB BLOCK: 1 | +----------------------------------------------- ------------------------+ | LNTYPE = COPPER VERSION = S2 QUAL = ON | | MASTER = Y DCHAN1 = 16 DCHAN2 = 0 | | PATTERN = D5H QUAL1 = 10 SEC. QUAL2 = 10 MIN. | | SMD = Y PERMACT = Y FCBAB = DF H | | CDG = N FIXEDTEI = 0 CNTRNR = 255 | | TEIVERIF = N CRC4REP = N | | DEV = INDEP | | INFO = | +----------------------------------------------- ------------------------+ AMO-LWPAR-111 LOADWARE PARAMETERS FOR NETWORKING MODULES DISPLAY COMPLETED; For Slave-side Configuration DISPLAY-TDCSU:1-3-25-1; H500: AMO TDCSU STARTED +------------------------ DIGITAL TRUNK (FORMAT=L ) -------------------------+ | DEV = S2CONN PEN = 1-03-025-1 TGRP = 27 | |------------------------------------------------ ---------------------------| | PROTVAR = PSS1V2 INS = Y SRCHMODE = CIR | | COTNO = 22 COPNO = 21 DPLN = 0 | | ITR = 1 COS = 32 LCOSV = 1 | | LCOSD = 1 CCT = PRI ECMA 4 DESTNO = 111 | | SEGMENT = 1 DEDSCC = DEDSVC = NONE | | FACILITY = DITIDX = SRTIDX = | | TRTBL = GDTR SIDANI = N ATNTYP = TIE | | CBMATTR = NONE NWMUXTIM = 10 TCHARG = N | | SUPPRESS = 0 DGTPR = CHIMAP = N | | ISDNIP = ISDNNP = | | PNPL2P = PNPL1P = 408 PNPAC = |
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 17 of 52
| TRACOUNT = 31 SATCOUNT = MANY NNO = 111 | | ALARMNO = 0 FIDX = 1 CARRIER = 1 | | ZONE = EMPTY COTX = 22 FWDX = 10 | | DOMTYPE = DOMAINNO = TPROFNO = | | INIGHT = CCHDL = | | UUSCCX = 16 UUSCCY = 8 FNIDX = 1 | | CLASSMRK = EC & G711 & G729OPT SRCGRP = | | TCCID = | |------------------------------------------------ ---------------------------| | BCNEG = N BCGR = 1 LWPAR = 0 | | LWPP = 0 LWLT = 0 LWPS = 0 | | LWR1 = 0 LWR2 = 0 | | DMCALLWD = DMCSEC = VNNO = | | SVCDOM = | | BCHAN = 1 && 30 | | | +------------------------------------------------ ---------------------------+ AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30 AMO-TDCSU-111 DIGITAL TRUNKS DISPLAY COMPLETED; DISPLAY-LWPAR:FORMAT=L,BLNO=0,TYPE=DIUS2; H500: AMO LWPAR STARTED +----------------------------------------------- ------------------------+ | LOADWARE PARAMETERS CIRCUIT TYPE: DIUS2 S OURCE:DB BLOCK: 1 | +----------------------------------------------- ------------------------+ | LNTYPE = COPPER VERSION = S2 QUAL = ON | | MASTER = N DCHAN1 = 16 DCHAN2 = 0 | | PATTERN = D5H QUAL1 = 10 SEC. QUAL2 = 10 MIN. | | SMD = N PERMACT = Y FCBAB = DF H | | CDG = N FIXEDTEI = 0 CNTRNR = 255 | | TEIVERIF = N CRC4REP = N | | DEV = INDEP | | INFO = | +----------------------------------------------- ------------------------+ AMO-LWPAR-111 LOADWARE PARAMETERS FOR NETWORKING MODULES DISPLAY COMPLETED;
Reference Clock Configuration, REFTA
For Master-side Configuration DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-3-25-1,KIND=ALL; H500: AMO REFTA STARTED +----------------------------------------------- --------------------------+ | R E F E R E N C E C L O C K C I R C U I T S | +--------------+---------+----------+---+------+ ------+------+-----+------+ | PEN | MODULE | DEVICE |PRI|ERROR | BLOCK |SUPP. |READY|SRCGRP| | | | | | | | |BUT | | | | | | | | | |ASYN.| | +--------------+---------+----------+---+------+ ------+------+-----+------+ | 1- 3- 25- 1 | DIU-N2 | S2CONN | 0| 0| N | | N | 1| +--------------+---------+----------+---+------+ ------+------+-----+------+ AMO-REFTA-111 REFERENCE CLOCK TABLE DISPLAY COMPLETED; For Slave-side Configuration DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-3-25-1,KIND=ALL; H500: AMO REFTA STARTED +----------------------------------------------- --------------------------+ | R E F E R E N C E C L O C K C I R C U I T S | +--------------+---------+----------+---+------+ ------+------+-----+------+ | PEN | MODULE | DEVICE |PRI|ERROR | BLOCK |SUPP. |READY|SRCGRP|
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 18 of 52
| | | | | | | |BUT | | | | | | | | | |ASYN.| | +--------------+---------+----------+---+------+ ------+------+-----+------+ | 1- 3- 25- 1 | DIU-N2 | S2CONN | 11| 0| N | | N | 1| +--------------+---------+----------+---+------+ ------+------+-----+------+ AMO-REFTA-111 REFERENCE CLOCK TABLE
DISPLAY COMPLETED;
Trunk Least Cost Routing Configuration
LDAT DISPLAY-LDAT:TYPE=LCR,LROUTE=1; H500: AMO LDAT STARTED +-------------------------------------------------- ----------------------------+ | LROUTE = 1 LDPLN NAME = ROPTCCM SERVICE = ALL | | TYPE = LCR DNN O OF ROUTE = 111 | | SERVICE INFO = | +------+-----+-----+----+-----+----------+--------- --+----------+------+-------+ | | | | | | SCHEDULE | CARRIER | | | | |LRTEL | LVAL|TGRP | ODR|LAUTH| ABCDEFGH | ZO NE| LATTR | LDSRT|COTIDX | +------+-----+-----+----+-----+----------+--------- --+----------+------+-------+ | 1| 1| 27| 111| 1 | ******** | 1 EMP TY| NONE | | 0 | | | DNNO = 111 | +-------------------------------------------------- ----------------------------+ AMO-LDAT -111 LCR-DIRECTIONS DISPLAY COMPLETED; DISPLAY-LDAT:TYPE=LCR,LROUTE=27; H500: AMO LDAT STARTED +-------------------------------------------------- ----------------------------+ | LROUTE = 27 LDPLN NAME = PRI 4 ECMA1 SERVICE = ALL | | TYPE = LCR DNN O OF ROUTE = 111 | | SERVICE INFO = | +------+-----+-----+----+-----+----------+--------- --+----------+------+-------+ | | | | | | SCHEDULE | CARRIER | | | | |LRTEL | LVAL|TGRP | ODR|LAUTH| ABCDEFGH | ZO NE| LATTR | LDSRT|COTIDX | +------+-----+-----+----+-----+----------+--------- --+----------+------+-------+ | 1| 1| 27| 15| 1 | ******** | 1 EMP TY| NONE | | 0 | +-------------------------------------------------- ----------------------------+ AMO-LDAT -111 LCR-DIRECTIONS DISPLAY COMPLETED; DISPLAY-LDAT:TYPE=LCR,LROUTE=165; H500: AMO LDAT STARTED +-------------------------------------------------- ----------------------------+ | LROUTE = 165 LDPLN NAME = PSTN 91650 SERVICE = ALL | | TYPE = LCR DNN O OF ROUTE = 89 | | SERVICE INFO = | +------+-----+-----+----+-----+----------+--------- --+----------+------+-------+ | | | | | | SCHEDULE | CARRIER | | | | |LRTEL | LVAL|TGRP | ODR|LAUTH| ABCDEFGH | ZO NE| LATTR | LDSRT|COTIDX | +------+-----+-----+----+-----+----------+--------- --+----------+------+-------+ | 1| 1| 23| 50| 1 | ******** | 1 EMP TY| NONE | | 0 | | | DNNO = 89 | +-------------------------------------------------- ----------------------------+ AMO-LDAT -111 LCR-DIRECTIONS DISPLAY COMPLETED;
RICHT
DISPLAY-RICHT:MODE=LRTE,LRTE=1;
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 19 of 52
H500: AMO RICHT STARTED +-------------------------------------------------- ---------------+ | LRTE = 1 NAME = ROPTCCM (NEUTRAL) LSVC = ALL | | DNNO = 111 PDNNO = 0 DESTNO =111 | | ROUTOPT = YES REROUT = YES PLB = YES FWDB L = NO | | DTMFCNV = FIX DTMFDSP = WITHOUT DTMFTEXT = | | DTMFPULS = PP300 BUGS = LIN ROUTATT = NO M AINGRP = 30 | | EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 30 | | INFO = | | NOPRCFWD = NO | | NITO = NO | | CLNAMEDL = NO | | FWDSWTCH = NO | | LINFEMER = NO | +-------------------------------------------------- ---------------+ | TGRP = 27 LDAT PRI ECMA 4 (NEUTRAL) S UBGROUP = 13 | +-------------------------------------------------- ---------------+ AMO-RICHT-111 TRUNK ROUTING DISPLAY COMPLETED; DISPLAY-RICHT:MODE=LRTE,LRTE=27; H500: AMO RICHT STARTED +-------------------------------------------------- ---------------+ | LRTE = 27 NAME = PRI 4 ECMA1 (NEUTRAL) LSVC = ALL | | DNNO = 111 PDNNO = 0 | | ROUTOPT = YES REROUT = YES PLB = YES FWDB L = NO | | DTMFCNV = FIX DTMFDSP = WITHOUT DTMFTEXT = | | DTMFPULS = PP300 BUGS = LIN ROUTATT = NO M AINGRP = 24 | | EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 24 | | INFO = | | NOPRCFWD = NO | | NITO = NO | | CLNAMEDL = NO | | FWDSWTCH = NO | | LINFEMER = NO | +-------------------------------------------------- ---------------+ | TGRP = 27 LDAT PRI ECMA 4 (NEUTRAL) S UBGROUP = 13 | +-------------------------------------------------- ---------------+ AMO-RICHT-111 TRUNK ROUTING DISPLAY COMPLETED;
LCR Out-dial Rules, LODR
DISPLAY-LODR:ODR=111,FORMAT=L; H500: AMO LODR STARTED +----------------------------------------------- --------+ | ODR POSITION CMD PARAMETER | +--------+-------------------------------------- --------+ | 111 | 1 ECHO 1 | | | 2 ECHO 2 | | | 3 END | +--------+-------------------------------------- --------+ H03: THE NEXT FREE ODR IS 3 AMO-LODR -111 ADMINISTRATION OF LCR OUTDIAL R ULES DISPLAY COMPLETED; DISPLAY-LODR:ODR=15,FORMAT=L; H500: AMO LODR STARTED +----------------------------------------------- --------+ | ODR POSITION CMD PARAMETER | +--------+-------------------------------------- --------+ | 15 | 1 ECHO 2 |
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 20 of 52
| | 2 END | +--------+-------------------------------------- --------+ H03: THE NEXT FREE ODR IS 3 AMO-LODR -111 ADMINISTRATION OF LCR OUTDIAL R ULES DISPLAY COMPLETED; DISPLAY-LODR:ODR=50,FORMAT=L; H500: AMO LODR STARTED +----------------------------------------------- --------+ | ODR POSITION CMD PARAMETER | +--------+-------------------------------------- --------+ | 50 | 1 ECHO 2 | | | 2 ECHO 3 | | | 3 END | +--------+-------------------------------------- --------+ H03: THE NEXT FREE ODR IS 3 AMO-LODR -111 ADMINISTRATION OF LCR OUTDIAL R ULES DISPLAY COMPLETED;
In-Band DTMF signaling:
In order to enable In-band DTMF signaling on digital stations for Voicemail applications, the station configuration has to be changed so that the parameter DTMFCTRD=Y.
Name and Number Restrictions:
To use Name and Number Restrictions, the station configuration should be changed so that the parameter SSTNO=Y, (Secret Station Number must be set to Yes). DISPLAY-SBCSU:5002; H500: AMO SBCSU STARTED ---------------------------- USER DATA ----------- ---------------------------- STNO =5002 OPT =OPTI COS1 =2 DPLN =1 MAINO =5002 CONN =DIR COS2 =2 ITR =1 PEN = 1- 3- 31- 2 LCOSV1 =6 COSX =0 INS =Y ASYNCT =500 LCOSV2 =6 PERMACT = LCOSD1 =6 SSTNO =Y EXTBUS = LCOSD2 =6 CBKB MAX =5 TRACE =N RCBKB =N ALARMNO =0 DFSVCANA= SPDI =0 RCBKNA =N HMUSIC =0 FLASH = SPDC1 = CBKNAMB =Y PMIDX =1 SPDC2 = COMGRP =0 SECR =N DIGNODIS=N DSSTNA =N STD =55 CALLOG =NONE DSSTNB =Y TEXTSEL =ENGLISH REP =0 OPTICOM =N OPTIUSB : VPI = IDCR =N OPTICA =1 OPTIS0A :0 VCI = APPM = OPTIDA =1 OPTISPA :0 PATTERN = OPTIABA :0 DCFWBUSY=N HEADSET =N APMOBUSR= APICLASS= DNIDSP =N HSKEY =NORMAL IPCODEC = SECAPPL = DTMFBLK =N IPPASSW = DTMFCTRD=Y BASICSVC= DVCFIG =OPTISET TSI =1 SPROT = SOPTIDX = DPROT = DOPTIDX = FPROT = FOPTIDX = ------------------- ACTIVATION IDENTIFIERS FOR FEA TURES ---------------------- HTOS :N DND :N HTOD :N VCP :Y TWLOGIN :N
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 21 of 52
HTOF :N CWT :N ------------------- FEATURES AND GROUP MEMBERSHIPS --------------------------- PUGR : ESSTN : KEYSYS :N NOPTNO : SRCGRP :(1 ) TCLASS : 0 HUNT CD :N ------------------- SUBSCRIBER ATTRIBUTES (AMO SDA T) ------------------------- NONE -------------------------------------------------- ---------------------------- AMO-SBCSU-111 STATION AND S0-BUS CONFIGURATIO N OF SWITCHING UNIT DISPLAY COMPLETED;
Configure Digital Station for MWI Application:
To get the MWI light to work, the station configuration should be changed so that the parameter PMIDX (phoneMail Index parameter) needs to point to the IDX identifier that identifies the Message Center’s Service Access Number. DIS-SBCSU:5002; H500: AMO SBCSU STARTED ---------------------------- USER DATA ----------- ---------------------------- STNO =5002 OPT =OPTI COS1 =2 DPLN =1 MAINO =5002 CONN =DIR COS2 =2 ITR =1 PEN = 1- 3- 31- 2 LCOSV1 =6 COSX =0 INS =Y ASYNCT =500 LCOSV2 =6 PERMACT = LCOSD1 =6 SSTNO =N EXTBUS = LCOSD2 =6 CBKBMAX =5 TRACE =N RCBKB =N ALARMNO =0 DFSVCANA= SPDI =0 RCBKNA =N HMUSIC =0 FLASH = SPDC1 = CBKNAMB =Y PMIDX =1 SPDC2 = COMGRP =0 SECR =N DIGNODIS=N DSSTNA =N STD =55 CALLOG =NONE DSSTNB =Y TEXTSEL =ENGLISH REP =0 OPTICOM =N OPTIUSB : VPI = IDCR =N OPTICA =1 OPTIS0A :0 VCI = APPM = OPTIDA =1 OPTISPA :0 PATTERN = OPTIABA :0 DCFWBUSY=N HEADSET =N APMOBUSR= APICLASS= DNIDSP =N HSKEY =NORMAL IPCODEC = SECAPPL = DTMFBLK =N IPPASSW = DTMFCTRD=Y BASICSVC= DVCFIG =OPTISET TSI =1 SPROT = SOPTIDX = DPROT = DOPTIDX = FPROT = FOPTIDX = ------------------- ACTIVATION IDENTIFIERS FOR FEA TURES ---------------------- HTOS :N DND :N HTOD :N VCP :Y TWLOGIN :N HTOF :N CWT :N ------------------- FEATURES AND GROUP MEMBERSHIPS --------------------------- PUGR : ESSTN : KEYSYS :N NOPTNO : SRCGRP :(1 ) TCLASS : 0 HUNT CD :N ------------------- SUBSCRIBER ATTRIBUTES (AMO SDA T) ------------------------- NONE -------------------------------------------------- ---------------------------- AMO-SBCSU-111 STATION AND S0-BUS CONFIGURATIO N OF SWITCHING UNIT DISPLAY COMPLETED;
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 22 of 52
Configure Message Center’s Service Access Number fo r MWI Application:
Since the MWI was tested with the Message Center integrated on Cisco Unified Communication Manager side, the PBX needs to configure an identifier for the Message Center’s Service Access Number in order for the MWI light to work. Without this identifier the MWI light will not work. ADD-RICHT:MODE=PM,IDX=1,SAN=6999; H500: AMO RICHT STARTED AMO-RICHT-111 TRUNK ROUTING ADD COMPLETED; DISPLAY-RICHT:MODE=PM; DISPLAY-RICHT:MODE=PM; H500: AMO RICHT STARTED +------+----------------------+-------------------- ----------+--------+ | IDX | SAN | NAME | TYPE | +------+----------------------+-------------------- ----------+--------+ | 1|6999 | |OTHER | +------+----------------------+-------------------- ----------+--------+ AMO-RICHT-111 TRUNK ROUTING DISPLAY COMPLETED;
Configure Digital Station’s Class of Service for Ma ilbox MWI application
DISPLAY-COSSU:TYPE=COS,COS=2,FORMAT=L; H500: AMO COSSU STARTED +------+-----------------+---------------+------ -----------+ | COS | VOICE | FAX | DTE | +------+-----------------+---------------+------ -----------+ | 2 |> | | | TA | NOCO | TA | | | TSUID | NOTIE | T NOTCR | | | TNOTCR | BASIC | BASIC | | | CDRS | | | | | CDRC | | | | | CDRIND | | | | | CDRINT | | | | | COSXCD | | | | | MB | | | | | DATA | | | | | CFNR | | | | | VCE | | | | | SPKR | | | | | FWDNWK | | | | | RERING | | | | | MSN | | | | | CFB | | | | | FWDDIR | | | | | FWDBAS | | | | | FWDECA | | | | | FWDEXT | | | | | CCBS | | | | | CW | | | | | GRPCAL | | | | | SUTVA | | | +------+-----------------+---------------+------ -----------+ AMO-COSSU-111 CLASSES OF SERVICE DISPLAY COMPLETED; DISPLAY-PERSI:TYPE=NAME,STNO=5002; H500: AMO PERSI STARTED +--------+----------------------------------------- +---------------------------+ | STNO | CHRISTIAN AND SURNAME CHARCON | ORGANIZATIONAL UNIT | +--------+----------------------------------------- +---------------------------+ | | | | | 5002 | HIPATH DT2* | |
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 23 of 52
| | | | +--------+----------------------------------------- +---------------------------+ AMO-PERSI-111 PERSONAL IDENTIFICATION DATA DISPLAY COMPLETED;
Siemens HiPath 4000 Software Release
DISPLAY-DBC:VERBOSE=N; H500: AMO DBC STARTED +-------------------------------------------------- ----------------------------+ | SYSTEM CLASSIFICATION : SYSTEM 80 (H 80 ) | | HARDWARE ASSEMBLY : EXTENDED COMPACT CXE (C XE ) | | OPERATING MODE : SIMPLEX | | RESTART TYPE : SYM | | HW-ARCHITECTURE : 4300 | | HW-ARCHITECTURE TYPE : 2 | | | | 'NO OF' HW VALUES | | LTG'S : 1 LTU'S : 4 LOG.LINE S : 12000 MTS BD /GSN: 1 | | SIUP'S/LTU: 4 TMD24'S PER LTU: 4 PHYS.POR TS: 6000 HWY /MTS BD: 64 | | HDLC /DCL : 5 PBC /DCL : 1 PBC'S : 17 | | LOG. SIU LINES : 26 | | LOG. CONF LINES : 35 | | LOG. DCL LINES : 36 | | DB DIMENSIONING-NAME : SMALL CONF-T ABLE VERSION: 1 | | DB SUSY'S: | | SWITCH NUMBER : L31903Q1930A00001 | | LOCATION : CUSTOMER | | BAPPL : BSMONO | | DBAPPL : DBSMALL | | SYSTEM_ID : | | | | OVERLAY RESOURCES IN ADP: | | SLOTS : 1000 MEMORY SPACE : 2000 KB | | OVERLAY RESOURCES IN SWU: | | SLOTS : 1000 MEMORY SPACE : 2000 KB | | OVERLAY RESOURCES BEI MONO PROCESSING: | | SLOTS : 400 MEMORY SPACE : 3000 KB | +-------------------------------------------------- ----------------------------+ AMO-DBC -111 DATABASE CONFIGURATION DISPLAY COMPLETED; DISPLAY-VEGAS:LIST=LONG; H500: AMO VEGAS STARTED SYSTEM NO. AMO APS NO. STAR T USER STATUS SWU: L31903Q1930A00001 REGEN P30252B4500B00108 07.0 6.09 22:01 CDBR FREE SWU RES CODE APS: P30252B4500S00108 (DIR FI LE: :PDS:APSI/PS/S0-EM0SC) SWU AMO CODE APS: P30252B4500B00108 (DIR FI LE: :PDS:APSI/PS/B0-EM0BC) SWU AMO TEXT APS: P30252B4500B00108 (DIR FI LE: :PDS:APSI/PS/B0-EM0BC) BREAK MARK : NO RESERVATION : NO ADS: L31903Q1930A00001 REGEN P30252B4500A00108 07.0 6.09 22:02 CDBR FREE ADS RES CODE APS: P30252B4500D00108 (DIR FI LE: :PDS:APSI/PS/D0-EM0DC) ADS AMO CODE APS: P30252B4500A00108 (DIR FI LE: :PDS:APSI/PS/A0-EM0AC) ADS AMO TEXT APS: P30252B4500A00108 (DIR FI LE: :PDS:APSI/PS/A0-EM0AC) BREAK MARK : NO RESERVATION : NO AMO-VEGAS-111 ADMIN. OF DATABASE GENERATION R UNS ON SUPPORT SYSTEM DISPLAY COMPLETED; DISPLAY-APS:ANS=Y,TYPE=PSALL,SP="Y0-EM0YC";
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 24 of 52
H500: AMO APS STARTED ADINIT STARTED PROGRAM SYSTEM : Y0-EM0YC VERSION NUMBER : 10 CORRECTION VERSION NUMBER : 001 PART NUMBER : P30252N4508BH5402|V3.0 R8 .2.54 PROGRAM SYSTEM WITH CODE SUBSYSTEMS INTERFACE VERSION: PROGRAM SYSTEM DOES NOT CONTAIN ANY INTERFACE VERSIONS ADINIT COMPLETED STATUS = H'0000 AMO-APS -111 SOFTWARE LOAD UPGRADE DISPLAY COMPLETED;
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 25 of 52
Local Cisco Unified Communications Manager Express (Cisco 3825) Configuration
C3825CME_CUE_1#show version
Cisco IOS Software, 3800 Software (C3825-IPVOICEK9-M), Version 12.4(22)YB1,
RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 18-Mar-09 21:33 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T10, RELEASE SOFTWARE (fc1)
C3825CME_CUE_1 uptime is 1 week, 1 hour, 29 minutes
System returned to ROM by reload at 01:54:44 UTC Sat May 30 2009
System image file is "flash:c3825-ipvoicek9-mz.124-22.YB1.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found
at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco 3825 (revision 1.2) with 227328K/34816K bytes of memory.
Processor board ID FHK1240F1YD
2 Gigabit Ethernet interfaces
31 Serial interfaces
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 26 of 52
1 terminal line
2 Channelized/Clear E1/PRI ports
1 cisco service engine(s)
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
125440K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102
C3825CME_CUE_1#show run
Building configuration...
Current configuration : 5169 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname C3825CME_CUE_1
!
boot-start-marker
boot system flash c3825-ipvoicek9-mz.124-22.YB1.bin
boot-end-marker
!
logging message-counter syslog
logging buffered 10000000
enable secret 5 $1$5KNs$DZpUuIL13L8wJYx6tH9XZ.
!
no aaa new-model
network-clock-participate wic 0
network-clock-select 1 E1 0/0/0
!
dot11 syslog
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 27 of 52
ip source-route
ip cef
!
no ipv6 cef
multilink bundle-name authenticated
!
isdn switch-type primary-qsig
!
voice-card 0
!
voice service pots
!
voice service voip
qsig decode
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
h323
sip
registrar server
no update-callerid
!
voice register global
mode cme
source-address 172.20.109.202 port 5060
max-dn 100
max-pool 185
load 7970 SIP70.8-4-2S
load 7961 SIP41.8-4-2S
load 7960-7940 P0S3-08-11-00
dialplan-pattern 1 .... extension-length 4
voicemail 2000
create profile sync 0176552385995309
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 28 of 52
!
voice register dn 1
number 4001
call-forward b2bua noan 2000 timeout 10
name Sachin-4001
huntstop
mwi
!
voice register dn 2
number 4002
name Dhoni-4002
huntstop
!
voice register pool 1
busy-trigger-per-button 2
id mac 001D.4595.4DBE
type 7970
number 1 dn 1
dtmf-relay rtp-nte
description Sachin-4001
codec g711ulaw
!
voice register pool 2
busy-trigger-per-button 2
id mac 000B.BEF9.E87D
type 7960
number 1 dn 2
dtmf-relay rtp-nte
description Dhoni-4002
!
archive
log config
hidekeys
!
controller E1 0/0/0
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 29 of 52
clock source line primary
pri-group timeslots 1-31
!
interface GigabitEthernet0/0
ip address 172.20.109.202 255.255.255.0
duplex auto
speed auto
media-type rj45
!
interface Service-Engine0/0
ip unnumbered GigabitEthernet0/0
service-module ip address 172.20.109.210 255.255.255.0
service-module ip default-gateway 172.20.109.202
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
media-type rj45
!
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn overlap-receiving
isdn incoming-voice voice
isdn contiguous-bchan
no cdp enable
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 172.20.109.1
ip route 172.20.109.210 255.255.255.255 Service-Engine0/0
!
no ip http server
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 30 of 52
no ip http secure-server
ip http path flash:
!
tftp-server flash:apps70.8-4-1-23.sbn
tftp-server flash:cnu70.8-4-1-23.sbn
tftp-server flash:cvm70sip.8-4-1-23.sbn
tftp-server flash:dsp70.8-4-1-23.sbn
tftp-server flash:jar70sip.8-4-1-23.sbn
tftp-server flash:SIP70.8-4-2S.loads
tftp-server flash:term70.default.loads
tftp-server flash:term71.default.loads
tftp-server flash:apps41.8-4-1-23.sbn
tftp-server flash:cnu41.8-4-1-23.sbn
tftp-server flash:cvm41sip.8-4-1-23.sbn
tftp-server flash:dsp41.8-4-1-23.sbn
tftp-server flash:SIP41.8-4-2S.loads
tftp-server flash:term41.default.loads
tftp-server flash:term61.default.loads
!
control-plane
!
voice-port 0/0/0:15
mwi
!
dial-peer voice 5000 pots
description To Siemens-HiPath
destination-pattern 500[23]
incoming called-number .T
supplementary-service qsig call-forward
direct-inward-dial
port 0/0/0:15
forward-digits all
!
dial-peer voice 6000 voip
description To_C3845CME_2
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 31 of 52
destination-pattern 4..[56]
session target ipv4:172.20.109.203
incoming called-number [45]...
no vad
!
dial-peer voice 10 voip
description To Voicemail
destination-pattern 2...
session protocol sipv2
session target ipv4:172.20.109.210
incoming called-number [245]...
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 1650 pots
description To PSTN
destination-pattern 1650364....
port 0/0/0:15
!
sip-ua
retry invite 2
mwi-server ipv4:172.20.109.210 expires 3600 port 5060 transport udp unsoli
cited
!
telephony-service
em logout 0:0 0:0 0:0
max-ephones 96
max-dn 192
ip source-address 172.20.109.202 port 2000
system message ABC Corp
load 7961 SIP41.8-4-2S
load 7970 SIP70.8-4-2S
load 7971 SIP70.8-4-2S
voicemail 2000
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 32 of 52
mwi relay
max-conferences 8 gain -6
call-forward pattern .T
moh music-on-hold.au
web admin system name cisco password cisco
dn-webedit
time-webedit
transfer-system full-consult
transfer-pattern ....
secondary-dialtone 9
create cnf-files version-stamp Jan 01 2002 00:00:00
!
ephone-dn 3 dual-line
number 4003
label 4003
description Dravid
name Dravid
call-forward noan 2000 timeout 10
huntstop channel
!
ephone-dn 4 dual-line
number 4004
label 4004
description Yuvraj
name Yuvraj
huntstop channel
!
ephone 3
mac-address 0012.4362.C1C2
type 7960
keep-conference
button 1:3
!
ephone 4
mac-address 000A.8A48.F9C9
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 33 of 52
type 7960
keep-conference
button 1:4
!
line con 0
line aux 0
line 194
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password cisco
login
!
scheduler allocate 20000 1000
end
C3825CME_CUE_1#
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 34 of 52
Cisco Unity Express Configuration
CUE1-210# show version
CUE1-210 uptime is 4 weeks, 2 days, 18 hours, 54 minutes
CPU Model: Celeron (Coppermine)
CPU Speed (MHz): 299.028
CPU Cache (KByte): 128
BogoMIPS: 587.77
SKU: Unavailable
Chassis Type: C3825
Chassis Serial: FHK1240F1YD
Module Type: AIM
Module Serial: FOC13091SGB
UDI Name: Not Available
UDI Description: Not Available
Compact Flash: 1GB
SDRAM (MByte): 256
CUE1-210#show run
Generating configuration:
clock timezone America/Los_Angeles
hostname CUE1-210
ip domain-name pbxlab.org
line console
exit
system language preferred "en_US"
ip name-server 172.20.2.181
software download server url "ftp://127.0.0.1/ftp" credentials hidden "6u/d
KTN/hsEuSAEfw40XlF2eFHnZfyUTSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xl
k2B35j0nfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmP"
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 35 of 52
privilege ViewRealTimeReports create
privilege ViewHistoricalReports create
privilege vm-imap create
privilege broadcast create
privilege ViewPrivateList create
privilege local-broadcast create
privilege ManagePublicList create
privilege manage-users create
privilege manage-passwords create
privilege ManagePrompts create
groupname Broadcasters create
username Dhoni create
username Dravid create
username pbx5003 create
username cisco create
username Gilchrist create
username pbx5002 create
username Sachin create
username Yuvraj create
privilege ViewRealTimeReports description "Privilege to view realtime repor
ts"
privilege ViewHistoricalReports description "Privilege to view historical r
eports"
privilege vm-imap description "Privilege to manage personal voicemail via I
MAP client"
privilege broadcast description "Privilege to send local or remote broadcas
t messages"
privilege ViewPrivateList description "Privilege to view private list"
privilege local-broadcast description "Privilege to send local broadcast me
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 36 of 52
ssages"
privilege ManagePublicList description "Privilege to manage public lists"
privilege manage-users description "Privilege to create, modify, and delete
users and groups"
privilege manage-passwords description "Privilege to reset user passwords"
privilege ManagePrompts description "Privilege to create, modify, or delete
system prompts"
privilege ViewRealTimeReports operation report.realtime
privilege ViewHistoricalReports operation report.historical.view
privilege vm-imap operation voicemail.imap.user
privilege broadcast operation broadcast.remote
privilege broadcast operation broadcast.local
privilege broadcast operation system.debug
privilege ViewPrivateList operation voicemail.lists.private.view
privilege local-broadcast operation broadcast.local
privilege local-broadcast operation system.debug
privilege ManagePublicList operation voicemail.lists.public
privilege ManagePublicList operation system.debug
privilege manage-users operation user.remote
privilege manage-users operation group.configuration
privilege manage-users operation user.configuration
privilege manage-users operation user.notification
privilege manage-users operation user.password
privilege manage-users operation user.pin
privilege manage-users operation system.debug
privilege manage-users operation user.mailbox
privilege manage-passwords operation user.password
privilege manage-passwords operation user.pin
privilege manage-passwords operation system.debug
privilege ManagePrompts operation prompt.modify
privilege ManagePrompts operation system.debug
groupname Administrators member cisco
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 37 of 52
groupname Broadcasters privilege broadcast
username Dhoni phonenumber "4002"
username Dravid phonenumber "4003"
username pbx5003 phonenumber "5003"
username Gilchrist phonenumber "4005"
username pbx5002 phonenumber "5002"
username Sachin phonenumber "4001"
username Yuvraj phonenumber "4004"
restriction msg-notification create
restriction msg-notification min-digits 1
restriction msg-notification max-digits 30
restriction msg-notification dial-string preference 1 pattern * allowed
backup server url "ftp://127.0.0.1/ftp" credentials hidden "EWlTygcMhYmjazX
hE/VNXHCkplVV4KjescbDaLa4fl4WLSPFvv1rWUnfGWTYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGW
TYHfmPSd8ZZNgd+Y9J3xlk2B35j0nfGWTYHfmP"
calendar biz-schedule systemschedule
open day 1 from 00:00 to 24:00
open day 2 from 00:00 to 24:00
open day 3 from 00:00 to 24:00
open day 4 from 00:00 to 24:00
open day 5 from 00:00 to 24:00
open day 6 from 00:00 to 24:00
open day 7 from 00:00 to 24:00
end schedule
ccn application autoattendant aa
description "Cisco-AutoAttendant"
enabled
maxsessions 4
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 38 of 52
script "aa.aef"
parameter "busClosedPrompt" "AABusinessClosed.wav"
parameter "holidayPrompt" "AAHolidayPrompt.wav"
parameter "welcomePrompt" "AAWelcome.wav"
parameter "disconnectAfterMenu" "false"
parameter "dialByFirstName" "false"
parameter "allowExternalTransfers" "false"
parameter "MaxRetry" "3"
parameter "dialByExtnAnytime" "false"
parameter "busOpenPrompt" "AABusinessOpen.wav"
parameter "businessSchedule" "systemschedule"
parameter "dialByExtnAnytimeInputLength" "4"
parameter "operExtn" "1001"
end application
ccn application ciscomwiapplication aa
description "ciscomwiapplication"
enabled
maxsessions 4
script "setmwi.aef"
parameter "CallControlGroupID" "0"
parameter "strMWI_OFF_DN" "8001"
parameter "strMWI_ON_DN" "8000"
end application
ccn application msgnotification aa
description "msgnotification"
enabled
maxsessions 4
script "msgnotify.aef"
parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.js
p"
parameter "DelayBeforeSendDTMF" "1"
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 39 of 52
end application
ccn application promptmgmt aa
description "promptmgmt"
enabled
maxsessions 1
script "promptmgmt.aef"
end application
ccn application voicemail aa
description "Cisco Voicemail"
enabled
maxsessions 4
script "voicebrowser.aef"
parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.js
p"
parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"
end application
ccn engine
end engine
ccn reporting historical
database local
description "se-172-20-109-210"
end reporting
ccn subsystem email
end subsystem
ccn subsystem fax
end subsystem
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 40 of 52
ccn subsystem jtapi
ccm-manager address 0.0.0.0
end subsystem
ccn subsystem sip
mwi sip unsolicited
end subsystem
ccn trigger http urlname msgnotifytrg
application "msgnotification"
enabled
maxsessions 2
end trigger
ccn trigger http urlname mwiapp
application "ciscomwiapplication"
enabled
maxsessions 1
end trigger
ccn trigger sip phonenumber 2000
application "voicemail"
enabled
maxsessions 4
end trigger
service voiceview
enable
end voiceview
voicemail broadcast recording time 300
voicemail default messagesize 240
voicemail notification restriction msg-notification
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 41 of 52
voicemail mailbox owner "Dhoni" size 300
expiration time 2
messagesize 120
end mailbox
voicemail mailbox owner "Dravid" size 300
expiration time 2
messagesize 120
end mailbox
voicemail mailbox owner "Gilchrist" size 300
expiration time 2
messagesize 120
end mailbox
voicemail mailbox owner "Sachin" size 300
expiration time 2
messagesize 120
end mailbox
voicemail mailbox owner "Yuvraj" size 300
expiration time 2
messagesize 120
end mailbox
voicemail mailbox owner "pbx5002" size 300
expiration time 2
messagesize 120
end mailbox
voicemail mailbox owner "pbx5003" size 300
expiration time 2
messagesize 120
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 42 of 52
end mailbox
end
CUE1-210#
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 43 of 52
Cisco Unified Communications Manager Express 2 (Cis co 3845) Configuration
C3845CME_2#show version
Cisco IOS Software, 3800 Software (C3845-IPVOICEK9-M), Version 12.4(22)YB1,
RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 18-Mar-09 22:45 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T10, RELEASE SOFTWARE (fc1)
C3845CME_2 uptime is 4 weeks, 2 days, 3 hours, 35 minutes
System returned to ROM by reload at 23:44:53 UTC Wed May 6 2009
System restarted at 16:44:52 UTC Wed May 6 2009
System image file is "flash:c3845-ipvoicek9-mz.124-22.YB1.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found
at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco 3845 (revision 1.0) with 484351K/39936K bytes of memory.
Processor board ID FHK1240F25Z
2 Gigabit Ethernet interfaces
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 44 of 52
2 Channelized (E1 or T1)/PRI ports
4 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
125440K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102
C3845CME_2#show run
Building configuration...
Current configuration : 3130 bytes
!
! Last configuration change at 20:07:16 UTC Fri Jun 5 2009
! NVRAM config last updated at 20:07:18 UTC Fri Jun 5 2009
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname C3845CME_2
!
boot-start-marker
boot system flash c3845-ipvoicek9-mz.124-22.YB1.bin
boot-end-marker
!
!card type command needed for slot 1
logging message-counter syslog
logging buffered 10000000
enable secret 5 $1$X4yD$9wEjyqZF0gCzZVhmhUEGt0
!
no aaa new-model
no network-clock-participate slot 1
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 45 of 52
!
dot11 syslog
ip source-route
ip cef
!
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
!
voice-card 0
!
voice-card 1
!
voice service pots
supplementary-service qsig call-forward
!
voice service voip
qsig decode
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
h323
sip
no update-callerid
!
archive
log config
hidekeys
!
interface GigabitEthernet0/0
ip address 172.20.109.203 255.255.255.0
duplex auto
speed auto
media-type rj45
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 46 of 52
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
media-type rj45
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 172.20.109.1
!
no ip http server
no ip http secure-server
!
tftp-server flash:P00308000500.bin
tftp-server flash:P00308000500.sb2
tftp-server flash:P00308000500.loads
tftp-server flash:P00308000500.sbn
!
control-plane
!
voice-port 0/0/0
!
voice-port 0/0/1
!
voice-port 0/0/2
!
voice-port 0/0/3
!
ccm-manager fax protocol cisco
!
dial-peer voice 4000 voip
description To_C3825_CME_CUE_1
destination-pattern 400[123]
session target ipv4:172.20.109.202
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 47 of 52
no vad
!
dial-peer voice 5000 voip
description To_Siemens_Hipath
destination-pattern 5...
session target ipv4:172.20.109.202
no vad
!
dial-peer voice 10 voip
description To Voicemail
destination-pattern 2...
session protocol sipv2
session target ipv4:172.20.109.202
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 9 voip
description To PSTN
destination-pattern 1..........
session target ipv4:172.20.109.202
no vad
!
sip-ua
mwi-server ipv4:172.20.109.202 expires 3600 port 5060 transport tcp
!
telephony-service
em logout 0:0 0:0 0:0
max-ephones 30
max-dn 150
ip source-address 172.20.109.203 port 2000
system message CBA Corp
load 7960-7940 P00308000500
voicemail 2000
max-conferences 8 gain -6
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 48 of 52
call-forward pattern .T
moh music-on-hold.au
dn-webedit
transfer-system full-consult
transfer-pattern ....
create cnf-files version-stamp 7960 Jun 01 2009 10:36:54
!
ephone-dn 5 dual-line
number 4005
label 4005
description Gilchrist
name Gilchrist
call-forward noan 2000 timeout 10
huntstop channel
mwi sip
!
ephone-dn 6 dual-line
number 4006
label 4006
description Ponting
name Ponting
huntstop channel
mwi sip
!
ephone 5
mac-address 0014.6A4D.3D96
type 7960
keep-conference
button 1:5
!
Ephone 6
mac-address 0014.6A3C.1BB9
type 7960
keep-conference
button 1:5
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 49 of 52
!
line con 0
line aux 0
line vty 0 4
password cisco
login
!
scheduler allocate 20000 1000
end
C3845CME_2#
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 50 of 52
AcronymsAcronymsAcronymsAcronyms
Acronym Definitions
CFB Call Forward when Busy
CFNR Call Forward when No Reply
CFU Call Forward Unconditional
IOS Internetworking Operating System
PBX Private Branch Exchange
PRI Primary Rate ISDN
SIP Session Initiation Protocol
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 51 of 52
Important InformationImportant InformationImportant InformationImportant Information
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE
WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO
BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE
FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR
INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA
ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
© 2009 Cisco Systems, Inc. All rights reserved.
Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 52 of 52
Corporate Corporate Corporate Corporate
HeadquartersHeadquartersHeadquartersHeadquarters
Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100
EuropeaEuropeaEuropeaEuropean n n n
HeadquartersHeadquartersHeadquartersHeadquarters
Cisco Systems International BV Haarlerbergpark Haarlerbergweg 13-19 1101 CH Amsterdam The Netherlands www-europe.cisco.com Tel: 31 0 20 357 1000 Fax: 31 0 20 357 1100
Americas Americas Americas Americas
HeadquartersHeadquartersHeadquartersHeadquarters
Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Tel: 408 526-7660 Fax: 408 527-0883
Asia Pacific Asia Pacific Asia Pacific Asia Pacific
HeadquartersHeadquartersHeadquartersHeadquarters
Cisco Systems, Inc. Capital Tower 168 Robinson Road #22-01 to #29-01 Singapore 068912 www.cisco.com Tel: +65 317 7777 Fax: +65 317 7799
Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on the Cisco Web site at www.cisco.com/go/offices.
Argentina • Australia • Austria • Belgium • Brazil • Bulgaria • Canada • Chile • China PRC • Colombia • Costa Rica • Croatia • Czech
Republic • Denmark • Dubai, UAE • Finland • France • Germany • Greece • Hong Kong SAR • Hungary • India • Indonesia • Ireland •
Israel • Italy • Japan • Korea • Luxembourg • Malaysia • Mexico • The Netherlands • New Zealand • Norway • Peru • Philippines •
Poland • Portugal • Puerto Rico • Romania • Russia • Saudi Arabia • Scotland • Singapore • Slovakia • Slovenia • South Africa • Spain •
Sweden • Switzerland • Taiwan • Thailand • Turkey Ukraine • United Kingdom • United States • Venezuela • Vietnam • Zimbabwe
© 2006 Cisco Systems, Inc. All rights reserved.
CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0601R)
Printed in the USA