R E Rig Engineering Case Studyrig-engineering.info/wp-content/uploads/2016/02/Case...-Access to...
Transcript of R E Rig Engineering Case Studyrig-engineering.info/wp-content/uploads/2016/02/Case...-Access to...
R Key word: Arctic III, New Lifeboat Installation, Global Assessment of Lifeboat Platform
E
Rig Engineering Case Study 3D Laser Scanning
Sheet 1 of 3
R RIG ENGINEERING
E www.rig-engineering.info Tel. (+44) 1224 627200
R Key word: Laser Scan, Clash Check, General Arrangement, Feasibility Study, Zoller + Fröhlich, Faro, Leica, ZF Laser Control, Pointools, ReCAP, Navisworks, Reverse Engineering, Spherical Panoramic High Definition Photo
E © Copyrights by Rig-Engineering
Rev. 1
Design Process Inside Point Cloud
- Functional layout creation
- Clash free design and installation
- Dimensionally accurate design allows for
pre-fabrication of structures and pipework
- Minimal amount of hot work on site
- No on site adjustment of structure
- Expensive and time consuming modelling of
existing structure is not required
- Instant visualization
3573 Helideck Monitor Walkways 3519 Column Catch Tank Piping Arrangement
Clash Detection - Clash check between new structure (3D
Models) and existing structure (Point Cloud)
- Clash check between two existing structures
(Point Clouds) without time consuming 3D
modelling
- Detailed reports with description of clash
and proposed solutions
3512 Zero Discharge Pipe Routing 3511 Crane Remedial Works
R Key word: Arctic III, New Lifeboat Installation, Global Assessment of Lifeboat Platform
E
Additional uses for Laser Scan data
- Drawing review against Laser Scan data to
report differences from original design and
update relevant documentation, i.e. As-Built
drawings
- Point Cloud data is archived for future use
- Source of visual information about
inaccessible areas (e.g. under deck and
tanks)
- Access to original imagery of subsea
equipment (e.g. ROV and BOP)
3418 Coupling LMRP and BOP Frames 3701 Hammermill Installation
Rig Engineering Case Study 3D Laser Scanning
Sheet 2 of 3
R RIG ENGINEERING
E www.rig-engineering.info Tel. (+44) 1224 627200
R Key word: Laser Scan, Clash Check, General Arrangement, Feasibility Study, Zoller + Fröhlich, Faro, Leica, ZF Laser Control, Pointools, ReCAP, Navisworks, Reverse Engineering, Spherical Panoramic High Definition Photo
E © Copyrights by Rig-Engineering
Rev. 1
Reverse Engineering
- Significant reduction of time and cost in
comparison to traditional survey methods
- Point Cloud contains detailed information
about existing structure geometry including
deformation and impairments
- 3D models based on Point Cloud can be
modified and used to produce 2D
documentation and FEM stress analysis
3897 BOP Lower Frame 3755 BOP Guide Cone
R Key word: Arctic III, New Lifeboat Installation, Global Assessment of Lifeboat Platform
E
Rig Engineering Case Study 3D Laser Scanning
Sheet 3 of 3
R RIG ENGINEERING
E www.rig-engineering.info Tel. (+44) 1224 627200
R Key word: Laser Scan, Clash Check, General Arrangement, Feasibility Study, Zoller + Fröhlich, Faro, Leica, ZF Laser Control, Pointools, ReCAP, Navisworks, Reverse Engineering, Spherical Panoramic High Definition Photo
E © Copyrights by Rig-Engineering
Rev. 1
Spherical 360⁰ Photographic Records
- Virtual walk through of clients assets
- Intuitive controls and key plan to easily navigate
around assets
- Information sharing and planning activities
remotely to reduce cost and avoid delays
associated with travelling to assets and multiple
surveys