Premier 10x8

10 x 8 Storage Building

Owner’s Manual10’ x 8’ (3.05m x 2.44m)Version 1.1

PLEASE READ OWNER’S MANUAL COMPLETELY BEFORE ASSEMBLING YOUR BUILDING.

ALL STATED SIZES ARE NOMINAL DIMENSIONS.

L108 Asheville / LC108 Asheville Ultra / S010 Winchester / S0102 Winchester Plus

S0103 Winchester Ultra / S1082 Woodbridge Plus / S1083 Woodbridge Platinum

© 2008 ROYAL OUTDOOR PRODUCTS CO.5289 HWY #7 Unit #7PO Box #56649 • Woodbridge, Ontario, Canada • L4L 8V3

PARTS LIST: Length in. (cm) Part No. Qty.Right Door Jamb Groove Panel 77 5/8 (197.1) DJ1 1Left Door Jamb Groove Panel 77 5/8 (197.1) DJ2 1 Side Wall Joiner Panels 69 (175.2) JT1 10Side Wall Groove Panels 69 (175.2) PT1 8Front/Back Wall Joiner Panels 73 15/16 (187.8) JT2 4Back Wall Groove Panels 77 5/8 (197.1) PT2 2Back Wall Joiner Panels 59 13/16 (151.9) JT3 2Back Wall Groove Panels 63 1/2 (161.3) PT3 2Back Wall Joiner Panels 67 1/4 (170.8) JT4 2Back Wall Groove Panel 68 7/16 (173.9) PT4 1Back Wall Joiner Panels 20 7/8 (53.0) JT5 4Back Wall Groove Panel 20 7/8 (53.0) PT5 3Wall Connector 72 1/4 (183.5) WC1 1Roof Joiner Panels 63 1/8 (160.4) JW1 10Roof Groove Panel 63 1/8 (160.4) PW1 8Corner Posts 69 (175.2) CN1 4Ridge Beam Sections 49 13/16 (126.5) RB1 2Header Assembly 31 3/16 (76.2) HD1 2Header Center 23 1/4 (59.0) HD2 1Roof Fascia Caps 49 13/16 (126.5) FC1 4Door Sweeps DS 2Astragal 71 5/8 (182.0) AST 1Right Rear Base Channel 59 1/16 (150.1) AL1 1Left Rear Base Channel 59 1/16 (150.1) AL2 1Side Base Channel 48 7/8 (124.2) AL3 2Side Base Channel 48 7/8 (124.2) AL4 2Right Front Base Channel 23 5/8 (60.0) AL5 1Left Front Base Channel 23 5/8 (60.0) AL6 1Door Lintel 71 15/16 (182.8) LN1 1Lintel Insert - Metal 73 7/8 (187.6) LT1 1Ridge Beam Steel Support Beams 67 3/8 (171.1) RS1 2Fascia Gable Right Front and Left Rear 63 1/8 (160.4) FG1 2Fascia Gable Left Front and Right Rear 63 1/8 (160.4) FG2 2Side Slope Wall Cap 48 7/8 (124.2) SC1 2Side Slope Wall Cap 48 7/8 (124.2) SC2 2Skylight Panel (minus 1 PW1) (Winchester Plus & Woodbridge Platinum only) 63 1/8 (160.4) SP1 2Ultraline Storage System (Winchester Ultra only) U008 1Asheville Ultra, Winchester Ultra and Woodbridge Platinum Models:Window WN1 1Side Wall Joiner Panels (minus 1 JT1) 36 15/16 (93.8) JT6 1Side Wall Groove Panels (minus 1 PT1) 36 15/16 (93.8) PT6 1Side Wall Joiner Panels 7 (17.8) JT7 1Side Wall Groove Panels 7 (17.8) PT7 1All Asheville and Winchester Models:Doors - Steel DR 2Woodbridge Model:Door Panels 70 (177.8) DP 2Door Trim Vertical 71 1/2 (181.6) DTV1 2Door Trim Vertical (pre drilled) 71 1/2 (181.6) DTV2 2Door Trim Horizontal 31 5/16 (79.5) DTH 4Accessory Bag:Ridge Beam Steel Support Beams 5 7/8 (15.0) RS2 2Ridge Beam End Caps REC 2Ridge Beam Joint Cover 4 (10.2) RJC1 1Roof Fascia Cap Covers 4 (10.2) FCC 2Door Handles HL 2Door Pins HP 4Hinge Plates - 2 Prong DH 4Hinge Screws #9 x 1" (2.54cm) Flat Quad DHS 16Slide Lock LK 1Vents VN 4Screws #10 x 3/4" (1.90cm) AS 200Ridge Beam Steel Insert Beam Bolt Set (Bolt, Washer, Nut) (1 extra set included) BS 8All Asheville and Winchester Models:Door Handle Screws #9 x 1" (2.54cm) Flat Quad DHS 8All Woodbridge Models:Door End Caps - Short 1 5/16 (3.4) DEC1 4Door End Caps - Long 12 1/2 (31.8) DEC2 4Door Handle Bolt Set (Bolt, Washer, Nut) - Black 1/4" x 2 1/2" DHBS 4Lock Brackets LB 2

Thank you for choosing the Royal Outdoor Products StorageBuilding. Please read this Owner's Manual completely beforeassembling your building. Retain manual and your dated sales slipfor future reference and warranty claims.

Assembly Safety InformationAs with any construction project, use common sense whenassembling your building. Royal Outdoor Products cannot beresponsible for any damages or injuries resulting from theincorrect use of any tools, equipment or the mishandling ofany of the building components.

• Use proper lifting procedures when handling the packages.

• Take care when handling the individual components andwear gloves to avoid cuts or scrapes.

• Follow proper operating procedures for any tools, ladders,etc. used when assembling the building.

• Protect your eyes. Always wear safety glasses when assem-bling building and when using power tools and hammers.

• Do not assemble building during high winds.

• Do not assemble building if parts are missing. A partiallyassembled building may be seriously damaged by highwinds.

• This building must be anchored to the foundation to pre-vent wind damage. See pages 4 and 5 for how to anchor.Screws for anchoring are not included.

THIS IS A MAINTENANCE FREE PRODUCT MADEOF WEATHERABLE VINYL AND AS SUCH DOESNOT NEED TO BE PAINTED. PAINTING OF THEPRODUCT OTHER THAN THE STEEL DOORS ON

THE ASHEVILLE AND WINCHESTER MODELSWILL VOID THE WARRANTY.

10 x 8 Storage Building 1

ATTENTION: Before you assemble the building:

PLEASE TAKE A COMPLETE INVENTORY OFALL PARTS USING THE PARTS LIST ANDPART IDENTIFICATION GUIDE PROVIDEDON PAGES 1, 2 AND 3. DO NOT ATTEMPTTO ASSEMBLE BUILDING IF PARTS AREMISSING OR DAMAGED.

ASHEVILLE AND WINCHESTER MODELS:THE ENTIRE DOOR INCLUDING ALLWOOD MUST BE PAINTED WITHIN THEFIRST 30 DAYS OF INSTALLATION WITH AHIGH QUALITY EXTERIOR TRIM PAINT.(Paint and other recommended supplies not included).

For assistance or replacement parts call:

1-877-GO-ROYALNOTE: PARTS ARE PACKAGED WITHIN OTHER PARTS.

PLEASE CHECK PACKAGE CAREFULLY.

JT2

LN1

HD2HD1 HD1

DJ2

CN1 CN1

CN1 CN1

FG2 FG1

AL2 AL1

AL6 AL5

JT1

JT1

JT1

JT1

JT1

PT1

PT1

PT1

PT1

JW1

JW1

JW1

JW1

JW1

PW1

PW1

PW1

PW1

JW1

JW1

JW1

JW1

JW1

PW1

PW1

PW1

PW1

JT1

JT1

JT1

JT1

JT1

PT1

PT1

PT1

PT1

AL4

SC2

FC1

FCC

FCC

AL3

SC1

FC1

RS1

RS2

RB1

RB1

RJC1

AL3FC1

SC1

AL4FC1

SC2

RS2

RS1

JT2

JT3

JT4

JT4

JT3

JT2

PT2

PT3

PT4

PT3

JT5

JT5

JT5

JT5

PT5

PT5

PT5

PT2

FG1 FG2

WC1

LT1

JT2

DJ1

REC

REC

DR DR

DTH DTH

DTH DTH

DTV

2

DTV

1D

TV1

DTV

2Asheville / Winchester

Woodbridge

JT6

PT6

JT7

PT7WN1

Asheville Ultra, Winchester Ultra,Woodbridge Platinum(Minus 1 JT1 & 1 PT1)

SP1

Winchester Plus,Woodbridge Platinum

(Minus 1 PW1)

Refer to parts list on opposite page for matching

PLEASE TAKE A COMPLETE INVENTORY OF ALL PARTS USING THE PARTS LIST AND PART IDENTIFICATIONGUIDE PROVIDED ON PAGES 1, 2 AND 3. DO NOT ATTEMPT TO ASSEMBLE BUILDING IF PARTS ARE MISSINGOR DAMAGED. IF YOU NEED REPLACEMENT PARTS PLEASE CALL 1-877-GO-ROYAL.

2 10 x 8 Storage Building

Full-Scale Hardware

Part Identification

Joiner Panel(JT1-JT7, JW1)

Groove Panel(PT1-PT7, PW1)

Slope Wall Cap(SC1-SC2)

Fascia Gable(FG1-FG2)

Roof Fascia Cap(FC1)

Ridge Beam(RB1)

Corner Post(CN1)

Base Channel(AL1-AL6)

Door Lintel(LN1)

Door Pin(HP)

Ridge Support Beam(RS1-RS2)

Ridge Beam Joint Cover(RJC1)

Roof Fascia Cap Cover(FCC)

Ridge Beam End Cap(REC)

Vent(VN)

Nut Washer Bolt(BS)

Door Handle(HL)


Door Handle Bolt Set (Black)(DHBS)

Screw#10 x 3/4" (1.90cm)

(AS)

Lock Bracket(LB)

Door End Cap -Short (DEC1)

Wall Connector(WC1)

Hinge/Handle Screw#9 x 1" (2.54cm)

(DHS)

Door Panel(DP)

Door Trim Vertical(DTV1, DTV2)

Door Trim Horizontal(DTH1)

Door End Cap -Long (DEC2)

Lintel Insert - Metal(LT1)

Tools Required• Power drill with Phillips® (#2) or a #2 square bit • Carpenter's square• Level • Rubber mallet • Hammer • Safety glasses • Gloves • 1/4” drill bit• Wrench - 7/16” size • Measuring Tape - Minimum 16’ feet (5m) • LadderPhillips is a registered trademark of PhillipsScrew Co.

Materials Needed• Foundation screws• Silicone Caulking• Paint for doors - Exterior grade enamel

(Asheville and Winchester models only)

Skylight Panel(SP1)

Door Sweep(DS)

Astragal(AST)

Hinge P lates(DH)

Slide Lock(LK)

Window(WN1)

Woodbridge Models

Door Handle(HL)

Ultraline Storage System(U008)

Asheville Ultra,Winchester Ultraand WoodbridgePlatinum Models

Winchester Plus and Woodbridge Platinum Models

Winchester Ultra Model

102'

' (25

9.08

cm)

99''

(251

.46c

m)

120'' (304.8cm)

123'' (312.42cm)

81 1/2'' (207.01cm)

41 1/2'' (105.41cm)

Concrete slab

4 10 x 8 Storage BuildingWoodbridge Platinum models come with a Royal Base Kit. Pleasefollow the instructions in the included B108 manual to set up your

foundation and when complete continue at pg 6.

Shed Base KitRoyal Outdoor Products is pleased to offer a new foundation option foryour storage building. This injection moulded base features a rugged

honeycomb design that supports heavy loads.For more information and ordering details call our Consumer Service

Centre at 1-877-GO-ROYAL or visit www.royaloutdoor.com.

How to Prepare the Building Site and Anchor the Building• Construct foundation (concrete slab or wooden platform) and anchor base

channels before assembling your building. Foundation and anchoring mate-rials are not included.

• Make sure that your building complies with your local building codes.• Before you excavate you will need to call local utility companies (e.g.

phone, cable, gas and electric) to ensure the area in which you plan to digis clear of underground cables or pipes. Utility company personnel willcome and mark these areas for you, usually at no charge. Always excavatethe base construction area slightly wider than the dimensions of the baseto give you some working room.

• Select a location that is free from ground water and provides suitabledrainage, ample room to erect the building, and an area that can be lev-elled properly.

• Decide on the type of foundation.• Foundation must be complete before unpacking and assembly can begin.• In selecting the site, allow approximately 5' (1.52m) of clearance on all

sides and 8’ (2.44m) more than the height of the building for assembly.

Exterior dimensions of 10' x 8' (3.05m x 2.44m) building:Roof Width: 122 15/16" (312.2cm)Roof Depth: 100 1/16" (254.1cm)Height: 93 9/16" (237.6cm)Wall Width: 118 3/16" (300.2cm)Wall Depth: 97 11/16" (248.2cm)

Concrete Slab OptionSlab should be 4" (10.16 cm) thick. To provide the best support for your buildingand to ensure that the corners are square, the slab must be sloped slightlyaway from the door opening and free of bumps and ridges. Follow BuildingCode requirements and provide a moisture barrier as specified by your con-crete contractor. OPTIONAL: Use Concrete Sealer paint on cured concretefloor to prevent moisture buildup in building.

Materials Needed:(not included)

(4) 10' x 2" x 4" (3.05m x 5.08cm x 10.16cm) for forms(2) 8' x 2" x 4" (2.44m x 5.08cm x 10.16cm) for forms

1.02 yd.5 concrete for 4" (10.16cm) thick slab

Cut Sizes:(2) 120" x 2" x 4" (304.8cm x 5.08cm x 10.16cm)(2) 102" x 2" x 4" (259.08cm x 5.08cm x 10.16cm)(14) 16" x 2" x 4" (40.64cm x 5.08cm x 10.16cm) with pointed ends

All stated sizes are nominal dimensions.

IMPORTANT NOTE ON CONDENSATION!All buildings are subject to condensation. Some of the causes of condensation arepoor ground conditions, improper foundation and construction and area climate. Condensation in most buildings is hidden. While wood will rot and metal will rust,condensation on PVC is similar to condensation on a window.For tips on preventing condensation please see the back page of the manual.

34'' (86.36cm)

17'' (43.18cm)

48'' (121.92cm)

48'' (121.92cm)

96'' (243.84cm)

48'' (121.92cm)

51'' (129.54cm)

99'' (251.46cm)

120'' (304.8cm)

24'' (60.96cm)

Wood platform

17 1/2'' (44.45cm)

34 1/4'' (86.99cm)

51'' (129.54cm)

96'' (243.84cm)

99'' (251.46cm)

120'' (304.8cm)

80'' (203.2cm)

96'' (243.84cm)

2" x 4" x 18" STAKESTYP. (4x)

64'' (162.56cm)

48'' (121.92cm)

32 1/4'' (81.92cm)16 1/2''

(41.91cm)

107 5/8'' (273.37cm)

82 1/2'' (209.55cm)

66 3/4'' (169.55cm)

Wood Platform OptionTo provide the best support for your building and to ensure that the corners aresquare, the platform must be sloped slightly away from the door opening and freeof bumps and ridges.

Materials to construct platform may be obtained at a lumber yard.

1. Begin by marking out the area to be excavated. Remove loose sod, topsoil or fillto allow for the placement of a compacted gravel base. Excavating is requiredto achieve a firm foundation which will prevent your base from shifting/sinkingand give overall stability. We recommend you dig to a depth that will allow for a2” gravel bed and will allow your base to be slightly above ground level. Insome areas it may be required to dig deeper to achieve this goal.

2. Fill the area with a minimum of 2” of medium to fine gravel. Grade your aggre-gate material as closely as possible to the final contour of the base surface. Toensure proper drainage make sure to grade the slope of the base installationaway from the front of the shed. Use either a hand tamper or plate compactorand firmly compact the gravel base material.

3. Have lumber cut to size and nail together following plan as shown.Recommended minimum nail length is 3”.

4. Position platform onto site and drive stakes into the ground to anchor platform.5. OPTIONAL: Paint floor to preserve platform.

Materials Needed:(not included)

(4) 10' x 2" x 4" (3.05m x 5.08cm x 10.16cm) pressure treated studs(13) 8' x 2" x 4" (2.44m x 5.08cm x 10.16cm) pressure treated studs(3) 3/4" x 4' x 8' (1.90cm x 1.22m x 2.44m) exterior grade plywood

Cut Sizes:From (2) 10' x 2" x 4" (3.05m x 5.08cm x 10.16cm) cut

(2) 120" x 2" x 4" (304.8cm x 5.08cm x 10.16cm)From (1) 10' x 2" x 4" (3.05m x 5.08cm x 10.16cm) cut

(8) 14 1/2" x 2" x 4" (36.83cm x 5.08cm x 10.16cm)From (1) 10' x 2" x 4" (3.05m x 5.08cm x 10.16cm) cut

(1) 14 1/4" x 2" x 4" (36.2cm x 5.08cm x 10.16cm)(6) 14 1/2" x 2" x 4" (36.83cm x 5.08cm x 10.16cm)(1) 18" x 2" x 4" (45.72cm x 5.08cm x 10.16cm) pointed for stake

From (9) 8' x 2" x 4" (2.44m x 5.08cm x 10.16cm) cut(9) 96" x 2" x 4" (243.84cm x 5.08cm x 10.16cm)

From (2) 8' x 2" x 4" (2.44m x 5.08cm x 10.16cm) cut(12) 14 1/4" x 2" x 4" (36.2cm x 5.08cm x 10.16cm)(2) 10 1/8" x 2" x 4" (25.72cm x 5.08cm x 10.16cm)

From (1) 8' x 2" x 4" (2.44m x 5.08cm x 10.16cm) cut(2) 14 1/4" x 2" x 4" (36.2cm x 5.08cm x 10.16cm)(3) 18" x 2" x 4" (45.72cm x 5.08cm x 10.16cm) pointed for stakes

From (1) 8' x 2" x 4" (2.44m x 5.08cm x 10.16cm) cut(8) 10 1/8" x 2" x 4" (25.72cm x 5.08cm x 10.16cm)(1) 14 1/2" x 2" x 4" (36.83cm x 5.08cm x 10.16cm)

Plywood:From (1) 3/4" x 4' x 8' (1.90cm x 1.22m x 2.44m) cut

(1) at 48" x 96" (121.92cm x 243.84cm)From (1) 3/4" x 4' x 8' (1.90cm x 1.22m x 2.44m) cut

(1) at 48" x 51" (121.92cm x 129.54cm)(1) at 48" x 24" (121.92cm x 60.96cm)

From (1) 3/4" x 4' x 8' (1.90cm x 1.22m x 2.44m) cut(1) at 48" x 51" (121.92cm x 129.54cm)(1) at 34" x 24" (86.36cm x 60.96cm)(1) at 17" x 24" (43.18cm x 60.96cm)


CAUTION:Special care must be taken when securing your building to afoundation constructed using “ACQ” (alkaline copper quater-nary compound) treated lumber. The preservativechemicals in this type of lumber has been provento react chemically with metal fasteners andmounting track hardware. Over time, this can leadto a failure of the fasteners or the mounting track itself.

It is important that if you choose an ACQ treated base foryour building, that you use a hot dipped galvanized orstainless steel screws for this purpose that are avail-able at your lumber or hardware store. It is veryimportant that you follow Royal’s recommendationthat the galvalume mounting track be iso-lated from direct contact with theACQ chemical by placing aheavy bead of silicone sealerbetween the track and thetreated lumber. This step willprevent water from entering underthe walls of your building and willprevent the possibility of a chemicalreaction between the metal track and thewooden components of your base.

145 7/8'' (370.5cm)

INSIDE CORNER TO INSIDE CORNER

70 15

/16'' (

180.2

cm)

97 13/16" (248.4cm)

92 1/2" (235cm)

AL4

AL2

AL4

AL3

AL1 AL3

AL6

AL5

Secure Base Channels (AL1-AL6) to foundationusing flat-head wood screws if your foundation iswood or flat-head concrete screws for a concreteslab. These screws are not included. The recom-mended size of flat-head screws to use is 3/16” x

3/4” Use pre-drilled holes in channels as a guide for screwplacement. Install a minimum of 6 screws in each side andrear channel piece and 4 screws in each front channel.

DOUBLE CHECK 70-15/16" (180.2cm) door opening dimensionbetween front Base Channels.

Base Channel Assembly

Parts Needed:2 Side Base Channels2 Side Base Channels1 Right Rear Base Channel1 Left Rear Base Channel1 Right Front Base Channel1 Left Front Base Channel

(Right and left are determined when facingthe front of building.)

Concrete or wood foundation must beinstalled. See pages 4 and 5 for instructionson how to prepare site and anchor building.

Position 8 Base Channels on platform as shown (rear channels are longest).Allow 70 15/16" (180.2cm) between front Base Channels for door placement. Usea carpenter's square to line up corners. Please note: The diagonal measurementincluded in the diagram may vary slightly from the actual measurement.

APPLY A CONTINUOUS BEAD OF SILICONE CAULK UNDERNEATH BASE CHANNELS,AROUND THE INSIDE PERIMETER OF THE BASE CHANNELS AND WHERE INDIVIDUALCHANNEL PIECES MEET.

CHECK 70 15/16" (180.2cm) door opening dimension between front Base Channels.

11

22

NOTE: Holes in exterior of Base Channels are for drainage only.DO NOT INSTALL SCREWS IN THESE DRAINAGE HOLES.


Joiner Panel

PT2 JT2

JT1 PT1 JT1

Groove Panel

General Assembly

The Joiner and Groove Panels are designed to make assembling your buildingeasy. The Joiner Panel and Groove Panel slide together easily without additionallubricants. There is not an inside or outside surface to the panels.

Some panels are shipped preassembled in groups of 3 or 4. Due to the weight of the pre-assembled panels, you may find it necessaryto disassemble some groups of 3or 4 in order to assembleyour building.

Back and Side Wall Assembly

Parts Needed:

2 Corner Posts10 Side Wall Joiner Panels8 Side Wall Groove Panels10 Back Wall Joiner Panels8 Back Wall Groove Panels1 Wall Connector

(Right and left are determined when facing the front of the building.)

It’s helpful to lay out all the required panels on the ground around yourfoundation in their proper sequence. Note that the back wall panels areangled at the top edge and vary in length.

Asheville Ultra, Winchester Ultra and Woodbridge Platinum Models:Additional Parts Needed:

1 Window2 Side Wall Joiner Panel2 Side Wall Groove Panel

NOTE: The window may be installed in either the left or right wall at anyof the shaded locations shown above. Plan on your window placementbefore proceeding with the installation and adjust the next stepsaccordingly.

Install the group of 2back wall panelslabeled PT2–JT2 intorear Base Channel.

33

44

66

77 Install a CornerPost CN1.

First,insert agroupof 3pre-

assembled sidewall panelslabeled JT1-PT1-JT1 into sideBase Channel atright rear corner.Make sure aJoiner Panelfaces the corner.

55


Asheville Ultra, Winchester Ultra andWoodbridge Platinum Models: GO TO STEP 9.Continue to build the right side wall insertinga group of panels labeled PT1-JT1-PT1-JT1-PT1-JT1 into side channel. Make sure you

hold onto panel until you insert it into channel; do notrelease panel and allow it to drop into channel. When

wall is complete, GO TO STEP 13.

88

PT6

JT6

Continue to build the rightside wall adding a GroovePanel PT6 followed by aJoiner Panel JT6. 99


1414

1010

1313

Install a group of 2 back wall panels labeledJT2–PT2 into rear Base Channel.

Insert a JT5 Joiner Panel to thePT2 panel at the back wall.Continue inserting panels PT5-JT5-PT5-JT5-PT5-JT5 .

Place the Wall Connector WC1 over thetop of panels JT5-PT5-JT5-PT5-JT5-PT5-JT5.1515

Insert a group of 4 side wall panels labeledPT1-JT1-PT1-JT1 into side channel at theright front corner.

Position thewindow so thatthe face withthe groove isfacing outside

and slide the Window WN1 intothe opening in the side wall asshown ensuring a snug fit.

NOTE: The Window must befully seated over the panels inorder to ensure proper installa-tion and aweather tightseal.

1111

Insert panels PT7-JT7 over top of theWindow WN1.

NOTE: If the panelsare not flush withthe top of the wallyour Window is notfully seated.

1212


1717

1818

2020 2121

Snap 2 piece Vent assembly VNprovided into hole located at topof JT4. Insert JT3-PT3-JT4 alongback wall on the left side.

HINT: A ladder may be requiredwhen assembling back wall.

1616

Install aCorner PostCN1.

Insert PT4 tocomplete theback wall.

Complete the left side wall inserting a group ofpanels labeled PT1-JT1-PT1-JT1-PT1-JT1.

Snap 2 piece Vent assembly VNprovided into hole located at top ofJT4. Insert JT3-PT3-JT4 alongback wall on the right side.

1919 Insert a group of 3 side wall panels labeled JT1-PT1-JT1 into side Base Channel beginning at theleft rear corner.

2424

Front Wall Assembly

Parts Needed:

2 Front Wall Joiner Panels1 Right Door Jamb Groove Panel1 Left Door Jamb Groove Panel2 Corner Posts 1 Door Lintel1 Lintel Insert2 Header Assembly1 Header Center4 Slope Wall Caps4 Fascia Gables 2 Ridge Beam Sections2 Ridge Beam Steel Support Beams2 Ridge Beam Steel Support Beams1 Ridge Beam Joint Cover8 Ridge Beam Steel Insert Beam Bolt Set

Screws #10 x 3/4" (1.90cm)

(Right and left are determined when facing thefront of building.)

Lay out all therequired panels onthe ground aroundyour foundation intheir proper

sequence. Note that the front wallpanels are angled at the top edge andvary in length. The Door Hinges mustface the outside of building on the rightand left Door Jamb Groove Panels.

2222

2323Install a CornerPost CN1.

Repeat to installJT2 and DJ2 in leftfront corner.

Add Door Lintel LN1 across top of front walls. TheDoor Lintel’s grooved surface should face up andscrew holes should face inside of building.Install Lintel Insert LT1 over top of Door Lintel LN1,making sure Lintel Insert LT1 is evenly spacedalong door opening and the hollow opening facesthe inside of the shed.

2525


Insert JT2 and DJ1in front BaseChannel at the rightfront corner.


SC1

SC2SC2

(Left Wall)SC1

(Left Wall)

28282727 Make sure Corner Posts CN1 and panels

are fully seated into Base Channels.Install a screw (#10 x 3/4” (1.9 cm)) ateach end of Door Lintel LN1 only.

Match up front and rearSlope Wall Caps (SC1, SC2)for both sides of building.Attach caps, pre-drilledholes facing inside. Pushdown to fully seat.

Install right Fascia GableFG1 on right side of frontwall. Install the otherright Fascia Gable FG1 toleft side of rear wall (asyou are facing front of

building). Repeat to install left Fascia GableFG2 on left side of front wall. Install the

other left Fascia Gable FG2 to the right side of rearwall (as you are facing front of building).

Have one person push down on the Fascia Gableswhile the other installs one screw at each end of thegables from the inside.

2929

Push Header Assembly HD1 all the way into theDoor Lintel LN1 over left and right side of the dooropening. Make sure the header is fully seated overtop of Lintel Insert LT1.Complete the header by sliding Header Center HD2all the way into Door Lintel LN1. Make sure

header is fully seated over top of Lintel Insert LT1.

2626


3434 Add Ridge Beam. Make surebottom wing of Ridge Beamfits under Fascia Gables (FG1& FG2) at each end of walls.

FLUSH ENDCUT BACK END

Slide on Ridge BeamJoint Cover RJC1 ontoRidge Beam. Apply abead of silicone aroundjoint where Ridge Beam

pieces meet. Slide Ridge Beam JointCover oversiliconedjoint.

RB1

RB1RJC1

If you do not have the recommended five feet of clearance on one side, you may fol-low these assembly instructions as an alternative:

Working from the inside of the building, slide roof Joiner Panel JW1into fascia FG at rear and front of building. Note: You must removeboth gables from the side that you have the clearance on to slide theJW1 panels down.

Next, install Groove Panel PW1 and continue until entire side of roof is complete.Important: Make sure you slide roof panels down approximately eight inches from topof roof to allow the installation of the Ridge Beam.

Install Ridge Beam as shown at Step 34 making sure bottom wing of Ridge Beam fitsunder Fascia Gables (FG1 & FG2) at each end of walls.

Slide Joiner Panel JW1 nearest outside wall into Ridge Beam and continue at Step 37.

3333

3232

IMPORTANT!

Slide a Ridge Beam section RB1 onto assembled SteelSupport Beam. Slide remaining Ridge Beam sectionRB1 onto assembled Steel Support Beam. Note: Makesure the flush ends of the Ridge Beam sections meet inthe middle of the assembly.

3131

IF YOU HAVE THE RECOMMENDED FIVE FEET OF CLEARANCE AT THE SIDES OF YOUR BUILDING

PROCEED TO STEP 34.

Overlap Distanceof Support Beams

36" (91.44cm)

OverallBeamLength

98 3/4"(250.83cm)

Ridge Beam Assembly

Layout Ridge Beam Steel Support Beams (RS1 &RS2) to proper length as in diagram. Line up holesand bolt Steel Support Beams together using bolt

set provided (Note: 4 bolts are to be used to fasten beams togetherat the centre and 2 bolts are to be used at either end to fasten 6”supports). Tighten bolts using 7/16” wrench.

3030

RS1

RS2 RS1

RS2

c)c)

a)a)

b)b)

Winchester Plusand WoodbridgePlatinum GO TOSTEP 39:

Next, add roofGroove Panel PW1 and installscrew into Ridge Beam hole onlywhere Groove Panel PW1 meetsJoiner Panel JW1.

Continue to add Roof Panels andscrews until both sides of roof arebuilt. Continue at Step 40.


3737

3838

Install 1 screw onlyinto corner ofRidge Beam RB1into hole nearestoutside wall.

3636Roof and Door Assembly

Parts Needed:

10 Roof Joiner Panels8 Roof Groove Panels2 Skylight Panels (Winchester Plus & Woodbridge Platinum only)4 Roof Fascia Caps2 Roof Fascia Cap Covers2 Door Sweeps4 Hinge Plates4 Door Pins2 Door Handles1 Astragal1 Slide Lock2 Ridge Beam End Caps16 Hinge Screws #9 x 1" (2.54cm) Flat Quad

Screws, #10 x 3/4" (1.90cm)All Asheville and Winchester Models:8 Handle Screws #9 x 1" (2.54cm) Flat Quad2 Doors - Steel

Woodbridge Model:2 Door Panels2 Door Trim Vertical2 Door Trim Vertical (pre drilled)4 Door Trim Horizontal4 Door End Caps - Short4 Door End Caps - Long4 Door Handle Bolt Set (Bolt, Washer, Nut)2 Lock Bracket

(Right and left are determined when facing the front of thebuilding.)

Lay out all the required panels on the ground around thebuilding in their proper sequence.

3535

Next, add roof Groove Panel PW1 and installscrew into Ridge Beam hole only whereGroove Panel PW1 meets Joiner Panel JW1.

Continue to add roof panels, Skylight PanelsSP1 and screws until both sides of roof are built.

NOTE: Before installing screws into the Skylight Panels SP1please drill a pilot hole, using a 5/32” drill bit, into the SkylightPanel using the existing pilot holes in your Ridge Beam as aguide to prevent it from cracking.

SKYLIGHT

EXISTINGPILOT HOLE

Working from the outsideof the building, slide roofJoiner Panel JW1 intoFascia Gable FG at rearof building.Hint: Make sure panel isfully seated into theRidge Beam.

3939


To verify that your door is standing properly, ensure that the twolarger panels are on top. The two smaller panels and the groove forthe Door Sweep DS are on the bottom. When the Hinge Plates DHare installed the prongs on the Hinge Plate DH must face outward.4040

DOOR TOP

DOOR BOTTOM

LARGEPANELS

SMALLPANELS

GROOVELEFT DOOR RIGHT DOOR

HINGELOCATION

HINGELOCATION

THE ENTIRE DOOR INCLUDING ALL WOOD MUST BE PAINTED WITHIN THEFIRST 30 DAYS OF INSTALLATION WITH A HIGH QUALITY EXTERIOR TRIM PAINT.

(Paint not included.) To ensure good paint adhesion, the prepainted surface should be lightly rough-ened to break the surface using 360 grit sandpaper in the flat areas and steel

wool along the embossment. The surface should then be cleaned to remove dirt,foreign debris, oils etc. and wiped dry with a clean towel.

Before you attach the HingePlate DH please identify thecorrect position of the hingeusing diagram aa. The correctposition of the hinge for the

left door is (a) with the etched crown right-sideup and facing you and (b) with the larger open-ing of the beveled screw holes facing you. Thecorrect position of the hinge for the right dooris (a) with the etched crown upside-down and

facing you and (b) with thelarger opening of thebeveled screw holes facingyou. Line up Hinge PlatesDH so that they are parallelwith the back of the doorframe as in diagram bb.Make sure that the twoprongs are facing outward.Insert the two outsidescrews first to ensure thehinge is properly aligned.

4242

4343 4444Position left door as shown.Tap Door Pins HP in both top and bottom hingeswith hammer. Repeat to install right door.

Install Door HandlesHL in pre-drilledholes with curvedend of handle facingoutside of building.

Install theDoorSweep DSonto eachdoor by

gently tapping the sweepinto the grooves on the doorbottom.Important: Do not installDoor Sweep DS until youhave painted the doors.

4141

INSERTTHESE

SCREWSFIRST

PRONGSFACE

OUTSIDEOF DOOR

PARALLELWITHDOOR

FRAME

BOTTOM

TOP

FRONT

BEVELEDHOLES

BACK

ETCHEDCROWN

Next, install Astragal AST on leftdoor of the building. PositionAstragal on inside of left door sothat the screw locator holes onthe Astragal are positioned on the

left door and the positioning fin on the Astragal fitstightly against edge of left door. Mark hole loca-tions on left door while holding Astragal in place.Drill 1/16” diameter holes, making sure that the drilldoes not penetrate the exterior side of the door.Install Astragal with #10 x 3/4” screws provided. GOTO STEP 57.

4545

aa

bb

DOORASTRAGAL

Door Installation - Asheville and Winchester Models:


Begin assembling the door by placing a Door Panel DP on aflat smooth surface so as not to damage it’s finish. Slide theDoor Trim Vertical piece DTV1 with no holesonto the Door Panel as shown makingsure that the top edge with the lip(see inset diagram) is facing up

and the bottom edge with the groove isfacing down. Take care to space thetrim evenly on the door frame.

4646Next, slide a Door Trim Horizontal piece DTH ontothe Door Panel as shown making sure that the topedge with the lip (see inset diagram) is facing up.Do not flip the door.4747

Then, slide a Door Trim Horizontal piece DTH onto the DoorPanel as shown making sure that the top edge with the lip(see inset diagram) is facing up.Adjust the Door Trim Vertical pieceas necessary to ensure it iscentered between the

top and bottom horizontal Door Trim.Do not flip the door.

4848

TOP EDGE (OUTSIDE)

BOTTOM EDGE (INSIDE)

LIP

Slide a Door Trim Vertical piece DTV2 with holes onto the doorpanel as shown making sure that the top edge with the lip (seeinset diagram) is facing up and the bottom edge with the groove isfacing down. Take care tospace the trim evenly onthe Door Panel.

Do not flip the door.

4949

TOP EDGE (OUTSIDE)


LIP

GROOVE

TOP EDGE (OUTSIDE)


LIP

Door Installation - Woodbridge Models:

TOP EDGE (OUTSIDE)


LIP

GROOVE


Loosen the screws on the hinges of the door only.Position left door as shown. Align prongs and tapDoor Pin HP in top and bottom hinge with hammer.Retighten hinge screws on the door. Repeat toinstall right door.

Install theDoor SweepDS ontoeach doorby gently

tapping the sweep into thegrooves on the door bottom.

NOTE: The Door Sweepmust be fully seated intothe door to allow for properoperation.

5353

5454

Identify the correct face of the door. The back of the door has agroove in the left and right door trim (Figure a). The front of the doorhas no groove. Position a door so that the Hinge Plates DH are onthe left side and the prongs on the Hinge Plates face outward(Figure b). Position the remaining door so that the Hinge Plates DH

are on the right side and the prongs on the Hinge Plates face outward (Figure c).

5252

HINGEPRONGS

FACEOUTSIDE

HINGEPRONGS

FACEOUTSIDE

LEFT ORIENTED RIGHT ORIENTEDBACK OF DOOR

GROOVE INDOOR TRIM

aa bb cc

Attach the Hinge Plates DH with the prongs facing upas shown using #9 x 1” (2.54cm)screws provided. Do notovertighten.5151

aa bb

Insert the barbed flap of the Door End Caps - Short DEC1into the slot of the unfinished corners of the Door TrimVertical piece DTV1 as in inset diagram aa. Push the DoorEnd Cap down fully so the top of the cap is flush with thetop of the door as in inset diagram bb.Insert the Door End Caps - Long DEC2 into the slot of the

unfinished corners of the Door Trim Vertical piece with holes DTV2. Do not flip the door.

5050

HOLES

NO HOLES


Door Juts Outward

Large Gap

Small GapDoor Alignment Tips

Before attempting to align doors,while inside the building, insert ascrew in the first hole of the Base

Channels (AL5 & AL6) at the Door Jambs (DJ1 & DJ2).Note: The door hinges have a special mechanism thatkeeps the door locked into the hinge even if pins areremoved. Do not remove the hinges.

1. Before you install screws in the Slope Wall Caps (roof/wallline), you must align the doors. DO NOT install screws unless the doors arelined up properly.

2. Ensure the doors are not upside down. The Door Sweep groove must be atthe bottom.

3. If you have installed your doors and you are experiencing problems, as inFigure a, use the following instructions to correct:

To obtain an even vertical gap between the doors, i.e. the doors are touch-ing at the top or the bottom, gently push the building back and forth, not sideto side. To obtain an even horizontal gap between the doors and the DoorLintel, i.e. the top of one door is higher than the other, gently push the shedside to side. You will notice that the doors shift as you push the building.

4. If you have installed your doors and you are experiencing problems as inFigure b, use the following instructions to correct:

In Figure b, the right door does not line up properly with the left doorbecause the bottom of the right door appears bent inward. To correct this,gently push on the building at the top of the front right corner (at the pointshown in Figure b) until the right door is aligned properly. If the left doorappears bent inward, correct the alignment by pushing on the top left cor-ner of the building.

5. Complete your assembly by installing a few screws at a time. For example,install two or three screws and check your doors. Repeat this procedureuntil all the screws are installed.

6. If you are still experiencing problems, call the 1-800 consumer service linefor assistance.

aa

bb

Next, install Astragal ASTon left door of the build-ing. Position Astragal oninside of left door so thatthe screw locator holes

on the Astragal are positioned on the leftdoor and the positioning fin on theAstragal fits tightly against edge of leftdoor. Mark hole locations on left doorwhile holding Astragal in place. InstallAstragal with #10 x 3/4” screws provided.

5656

DOORASTRIGAL

5757Door

Door Jamb

Install Screw

Base Channel

BACK OF DOOR

35 3/4"

Measure down 35 3/4” fromthe top of the right door trimfacing the back of the rightdoor and mark a line. Closeboth doors and from the

inside, extend the line across to the left door.Place a Lock Bracket LB on the door so thatthe screw hole is on the line you previouslymarked and drill through to the outer edge ofthe door using a 1/4” drill bit. Place the bot-tom end of the Door Handle DH over the holeand lightly fasten in place using a DoorHandle Bolt Set. Visually line up the top of theDoor Handle so that it is parallel to the edgeof the door trim and drill through to the holeto the inner edge of the door using a 1/4” drillbit. Fasten the upper part of the Door Handlein place using a Door Handle Bolt Set. Repeatto install the remaining Lock Bracket andDoor Handle on the other door.

Important: The above measurement of 35 3/4”will place the door handle at average doorheight. You may wish to increase ordecrease this measurement to place thedoor handle at a height that suits your needs.

5555

Asheville Ultra,Winchester Ultraand WoodbridgePlatinum Models:GO TO STEP 61.

Before installing screws into theskylight please drill a pilot hole intothe skylight panel using the existingpilot holes in your fascia cap andslope wall cap as a guide to preventit from cracking.


Finish byinstalling ascrew at thebottom of allpanels -front, back

and sides into BaseChannels on inside only. Note: holes in exterior ofBase Channels are fordrainage only. DO NOTINSTALL SCREWS IN THESEDRAINAGE HOLES.

6262

Mark holelocations oninside ofdoor whileSlide Lock LK

is held into the hole providedin the Door Lintel LN1. Drill 3holes, 1/16" diameter into thedoor (make sure that the drilldoes not penetrate the exteri-or side of the door). InstallSlide Lock LK with #10 x 3/4”(1.90cm) screws provided. NOTE: With Astragal AST inplace you may need to posi-tion Slide Lock over top ofAstragal in order to line upSlide Lock with pre-drilledhole in Lintel.

6363

First, install lower screws on Slope Wall Caps (SC1 & SC2)into side wall panels. Next, inspect side wall to ensure it isvisually straight from the front corner to the back corneralong the length of the building. If your wall is not straight,correct it by pushing the wall inwards or outwards

accordingly. Upon confirmation, install screws into the top of Slope WallCaps (SC1 & SC2) into the roof panels.

Install #10 x 3/4"(1.9cm) screws inthe Door Lintel LN1and front FasciaGables (FG1 & FG2).

Have one person push the Lintelupward at the centre so as theLintel bends upward slightly whilethe remaining screws are installedin the Lintel.

6161

5959

6060Screw Installation

Inside the building, beginning in each corner, secure rear FasciaGable FG with screws to back wall panels. Pre-drilled holesshould line up where the panels are joined. It is helpful to haveone person on the outside of the building pushing down on the

Fascia Gable FG while the second person inserts the screw from the inside.Install 3 screws into both front Fascia Gables FG beside door opening while oneperson holds the Fascia Gables FG down from the outside.IMPORTANT: Be sure to check door alignment several times during screwinstallation to ensure building has not moved out of alignment. If it has, realignand resume installation of screws.

5858EXISTINGPILOTHOLE

SKYLIGHT


6868Ultraline Storage System (Winchester Ultra only)

6767Insert Ridge Beam EndCaps REC in front andback, and install screws.

6565 Snap Roof Fascia Cap Covers FCC inplace where the Roof Fascia Caps FC1meet.

Install screws, alternatingtop and bottom pre-drilledholes in Roof Fascia CapsFC1.

6666

6464 Cover roof ends with Roof Fascia Caps FC1. Make sure RoofFascia Caps FC1 are flush with roof panels at each end.

Position track correctly as shown in the profile drawing at rightand insert screws into the v-grooves of the track. Note: Thescrews must line up with the seams of the building to ensuremaximum strength. Do not overtighten screws or vinyl will strip.

SEAM SEAM

V-GROOVE SCREW

6969 Install brackets by placing the top portion in first (A). Then slide in the bottom portion (B). Finally, shift the bracket down into its final position (C).

20 10 x 8 Storage BuildingRoyal Outdoor Products Vinyl Storage Buildings

10 Year Non-Transferable Limited WarrantyRoyal Outdoor Products Co.

5289 HWY #7 Unit #7PO Box #56649

Woodbridge, Ontario, CanadaL4L 8V3

Royal Outdoor Products Co., a division of Royal Group Inc., (" Royal") in respect of Vinyl Storage Buildings manufactured by it (hereinafter referred to as "Products")warrants to you the original purchaser of Products, that subject to the terms and conditions herein contained, the Products are and will be free from defects in materialsand workmanship that result in warping, rotting, corroding, flaking, pealing, blistering, or abnormal discoloration of surfaces. This warranty will remain in effect for aperiod of 10 years as long as you are the original purchaser of the Product and if the Product used in non-commercial applications. All failures to Products covered bythis warranty will be repaired, replaced or restored by Royal in accordance with the terms and conditions of this warranty. By acceptance and use of the Products, youagree with Royal’s liability, and replacement of the Products at Royal’s option, as provided herein.

Products which experience color change due to normal weathering are excluded from this warranty (including non-uniform fading and color changes resulting fromunequal exposure of panels to the sun and elements.) For the purpose hereof, the term "normal weathering" means exposure to ultraviolet (sun) light, and extremes oftemperature and atmosphere which will cause any colored or painted surface to fade, darken, chalk or acquire a surface accumulation of dirt or stains. The severity ofthese conditions depends on air quality, the geographic location of the property at which the Products are installed, and other local conditions over which Royal has nocontrol. Royal shall not be liable for and this warranty does not apply or extend to any failure, defects or damages arising from or connected with, without limitation,misuse, neglect, faulty or improper installation.

This warranty is void if structural parts and components not supplied by Royal are used. Failure, damage, defects or malfunctions resulting from misuse, abuse, negli-gence, alteration, accident, lack of proper maintenance, impact of foreign objects, hail, tornado, hurricane, other violent storm, flood, fire, pollutants, chemicals, acts ofGod and other causes beyond Royal’s control shall not be considered defects under this warranty and are not covered in any way by this warranty. Royal shall not beliable for inconvenience, labor, loss of time, maintenance, removal or reinstallation of the Products or other incidental, special or consequential damages arising in rela-tion to the purchase or use of the Product. This warranty is void if the surface of the Product is covered with paint or any other foreign material, other than as specificallydirected in the owners manual included with the Product.

The 10 Year Limited Warranty-Non-Commercial Applications coverage provided by this warranty is extended to cover individuals who are using the Products as home-owners and does not extend to Products purchased by or installed upon property owned by and other entities, including, without limitation, corporations, partnerships,trusts, estates, governmental agencies or bodies, religious organizations, schools, condominiums, or co-operative housing arrangements, or installed on apartment build-ings or any other multi-housing arrangements.

This warranty becomes valid only after the product warranty card has been submitted to Royal Outdoor Products Co within 30 days of installation. The warranty can alsobe activated by contacting Royal Outdoor Products Co, Customer Care Center at 1 877 GO ROYAL (467-6925) or by visiting our web site at www.royaloutdoor.com.

Warranty Claims:The owner must give prompt notice of any defects to obtain warranty service. Should the Products contain a manufacturing defect promptly contact the Royal OutdoorProducts Co, Customer Care Center at 1 877 GO ROYAL (467-6925) or by mail at 5289 HWY #7 Unit #7, PO Box #56649, Woodbridge, Ontario, L4L 8V3 to register theclaim with a customer care representative. Royal will require proof of purchase, Product serial number and a clear photograph of the defective part(s) (or actual part(s)if requested). Royal will, at its option, repair or replace such defective part(s) free of charge, including freight charges within North America. Royal’s shipping servicewill deliver parts under this warranty within 8 to 10 business days. This warranty is not applicable outside North America. In order to ensure warranty coverage you mustregister your Product within 30 days of purchase. Warranty registration can be accomplished by calling 1 877 GO ROYAL (467-6925), mailing in the completed Productwarranty card or registering online at www.royaloutdoor.com.

Shipping Instructions: If requested for inspection, defective parts must be shipped to Royal Outdoor Products Co, Customer Care Center, shipping address will be provided upon approval.Please include the following information in the package: full name, home address, telephone number, Product model number and part number. When returning productplease use an insured method of delivery such as Fed Ex insured accordingly, with the signature option on, or your preferred courier service. You must pay for returnshipment, as we will not accept C.O.D. returns or any additional shipping charges, which may occur when packages are entering into Canada.

Royal reserves the right to discontinue or change any of its Products, including colors, without giving notice to the purchaser. Should a Product covered by this warrantybe unavailable, Royal reserves the right to substitute a Product that is of equal quality according to Royal’s sole discretion or to refund the portion of the original pricefor defective part of the Product reflective of its original contribution to the cost of the Product.

THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, LIABILITES OR OBLIGATIONS OF ROYAL EITHER EXPRESSED OR IMPLIED, EXCEPT THAT THE DURA-TION OF ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN TIME TO THE DURATION OF THIS WARRANTY.ROYAL SHALL IN NO EVENT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL OR SPECIAL DAMAGES OF ANY KIND FOR BREACH OF ANY EXPRESS WRITTEN OR ORALOR IMPLIED WARRANTY ON PRODUCTS. YOUR EXCLUSIVE REMEDY SHALL BE ENFORCEMENT OF THIS WARRANTY UPON THE TERMS AND CONDITIONS HEREIN CON-TAINED. NO REPRESENTATIVE OF ROYAL OR ITS DISTRBUTORS OR DEALERS IS AUTHORIZED TO MAKE ANY CHANGE OR MODIFICATION TO THIS WARRANTY.

Some jurisdictions do not allow limitation on how long an implied warranty lasts, so the limitations contained herein above may not apply to you. Some jurisdictions donot allow the exclusion or limitation on consequential or special damage, so the above limitations or exclusions may not apply to you. This warranty gives you specificlegal rights, and you may also have other rights, all of which vary from jurisdiction to jurisdiction.

Premier Series 10’ x 8’ Storage BuildingOwners Manual

10’ x 8’ (3.05m x 2.44m)

5289 HWY #7 Unit #7 • PO Box #56649 • Woodbridge, Ontario, Canada • L4L 8V3http://www.royaloutdoor.com

A Division of Royal Group Inc.

Structure made in CanadaPrinted in CanadaU.S. Pat. appl’d for

Attach serialnumber sticker from

plastic crate cover herefor future reference.

Instructions For Cleaning

Congratulations on your purchase of a fine quality Storage Building from Royal Outdoor Products. Withproper maintenance your vinyl storage building will exceed your expectations for years to come.Cleaning:It is recommended that you clean your storage building at least twice a year to prevent a build up of dirt.Most often a heavy rain is sufficient in cleaning it or you may want to wash your building with a standardgarden hose. If neither rain nor hosing does a satisfactory job, follow these instructions. Cleaning your newbuilding is quite easy and the following cleaners can be utilized Simply Green™, Fantastic™, Soft Scrub™,Lestoil™, Murphy’s Oil Soap™, Windex™, and Tilex™, you may also consider a mixture of 30% vinegar andwater solution to use as a cleaner. Use a soft cloth or an ordinary long handled soft bristle brush to wash.Avoid using any chlorine-based cleaner, nail polish remover laundry, detergent, furniture polish cleaner, andother cleaners containing organic solvents which could effect the surface appearance of the building. Forstains such as pencil, paint, oil stains and tar, use a mildly abrasive cleaner with the understanding that anyabrasive material could have a deleterious effect on the surface appearance. Caution:Any material, which covers up the vinyl, may cause serious damage and is not covered by the warranty.Remove leaves, dirt, sap or excessive snow which may accumulate on the roof, do not place any lattice,vines, tar, shingles, tarps or other materials such as paint onto the surface of the vinyl. Important:Any structural modifications to the building will void the product warranty. Always refer to your productmanual for guidance. If you require additional assistance contact 1-877-GO-ROYAL (467-6925).

Tips to Prevent Condensation• Choose the proper site for construction. Do not place the building in a swampy, wet or low lying area.

Keep the building away from ground water run-off.• Follow the base preparation steps in the manual. Ensuring your foundation is sloped slightly away from the

doors and the area around the building is graded to permit water drainage away from the building site isessential.

• Follow the assembly instructions in the manual. Applying silicone caulking and installing screws onlywhere directed will keep any water from entering the building and allow the building to drain properly.

• Your Royal Storage Building is supplied with suitable ventilation to eliminate normal condensation. Severe cases may require additional ventilation. Simply phone 1 877 GO ROYAL (467-6925) and one of ourCustomer Care representatives will tell you how you can purchase additional vents for your model.

Premier 10x8

Documents

Transcript of Premier 10x8