PEUGEOT 207 (2006 - 2011) MKi + CK (EN_US).pdf

207 207

This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.

207

Installation manual: Parrot MKi + Parrot CK3100 range

The brand name PEUGEOT 207 and the PEUGEOT logo are the property of AUTOMOBILES PEUGEOT. This document is only valid for the vehicle model 207® year 2006 to 2011, excluding all other models in the same range and excluding later modifications made to the vehicle by the manufacturer. The Parrot brand name and logos are the exclusive property of Parrot SA.

207 207


Accessories required

Disassembly 20min

Kit installation 30min

Refitting 20min

Testing 15min

Total 1h25min

YES ACC wire

NO ISO

YES UNIKA

FRONT SPEAKER TEL mode

ALL MUSIC mode

Fitting time (estimated) / Main features

Tools

- TORX screwdriver

- Multimeter or Test lamp

- Hose clamp

- Electrical tape

- Round file (or a knife)

"Please contact your Wholesalers to purchase accessories."

Kram ref. Dealer ref.

CK range 86 165 9706 AP

MKi range 84744 9706AT

Photos not contractually binding

CK range MKi range

Updating

Plastic trim removal tools FACOM / BERNER

FACOM Sleeve DX-25 (n°4 spanners)

To get the most out of your hands-free kit we recommend that you update your software regularly. The update procedure can be found at

www.parrot.com/usa/support/downloads

http://www.parrot.com/uk/support/downloads

207 207


Disassembly

207 207


Disassembly 1 / 2

Insert the removal tools into the slots on each side of the radio.

Unclip, pull and remove the radio taking care to unplug

the connector and the antenna.

Using the plastic trim tools, unclip the storage compartment.

Remove it in the same way as you did the radio.

1

3

2

4

5 6

Using the plastic trim tools, unclip the air vent/central

display surround.

Remove screws 1 and 2.

If you have the 6 CD changer

1 2

207 207


Disassembly 2 / 2

Using the plastic trim tools, unclip the front without removing it.

Using the plastic trim tools, unclip the clip located on the left side of

the dashboard.

Release the fuse box cover. Remove the door seal on the driver’s side.

7

9

8

10

207 207


Microphone passage

Stick the bracket supplied after cleaning the surface to the

windscreen. Run the cable under the headliner towards the driver

side door.

Run the cable replacing the seal on the passenger door.

Pass the cable into the dashboard on the left side and

into the fuse box.

Run the cable towards the radio, attaching it under the dashboard

with wire ties.

1

3

2

4

207 207


Feeding the accessory cable

In the glove box unclip the RCA connection support and

disconnect it.

Using a knife or drill, make a notch on the back of the support.

1 2

Pass the cable from the hole towards the radio.

Reconnect and re-fit the cover leaving a sufficient length of

cable.

3 4

207 207


Power supply

Cut the red wire in front of the fuse for adaptor 84744 or for the

kit bundle supplied for the CK connect a wire to it.

Run the wire from the radio housing towards the steering

column.

Run it under the steering wheel using a guide.

Fit a 2.5mm terminal and connect the wire to the yellow

fuse holder. (Check that the +12V is permanent.)

1

3

2

4

This procedure for wiring the permanent +12V only applies to cars with the 6 CD changer.

207 207


Fitting the hands-free system 1 / 2

Connect the adaptor 86165 for the CK or the 84744/9706AT for the Mki to the original

connector. Connect all of the wires to the blue box as shown in the diagram below. Test the

assembly before reassembly then slide all the cables behind the glove box and attach them

with wire ties.

1

ISO adapter

207 207


Fitting the hands-free system 2 / 2

Stick the support supplied to the display panel after having cleaned

the surface.

Run the cable between the panel and the dashboard towards the

radio.

Replace screws 1 and 2.

2

4

3

12

Clip the display panel and its surround back on. (Make sure that

you DO NOT cut the cable.)

4

MKi9100 option

Pull the cable through from the bottom of the air vents and stick the bracket to the surface. (After cleaning it.)

4b

207 207


Testing

Before refitting the system, switch the kit on using the ignition (or by starting the car). By pushing the central knob

of the remote control, check:

1 - That the menu is displayed on the screen. (Language or iPod.) 2 - That the system can be muted. (Click on the blue box.) 3 - That there is no sound coming from the speakers. 4 - That the sound from the voice menu is coming out of the front speakers. 5 - Then turn off the ignition, check that the kit switches off and that the "goodbye" message appears on the screen. (If this fails, reverse the fuses on the kit's wiring harness.) 6 - Pair a telephone with the kit to make a call. (Check that both the microphone and the kit are working.)

207 207


Reassembly

Refit the system using the following procedure: 1 – Re-install the radio reconnecting the adapter and antenna. 2 - Replace the storage compartment. 3 – Re-fit the fusebox cover by pushing hard. 4 – Re-fit the panel on the left-hand side of the dashboard.

PEUGEOT 207 (2006 - 2011) MKi + CK (EN_US).pdf

Documents

Transcript of PEUGEOT 207 (2006 - 2011) MKi + CK (EN_US).pdf