PE100-1ProductSpecifications

APPLICATIONLeviton’s PE100-1 Power Extender allows a dimmingzone’s power handling capacity to be extended to afull 1920W/VA on 120V input power. It allows a zoneto dim or switch a fully loaded circuit of incandescentand magnetic low voltage loads only.

FEATURES & BENEFITS• Works with incandescent, magnetic low voltage,

halogen or neon/cold cathode lighting• Low-end trim available for setting the

minimum brightness level• Emulates the characteristics of the dimmer

that it is connected to in terms of dimming range and resolution

• Works with any Dimensions Multi-zoneController/Dimmer to extend load capacity on any zone

PE1 00-1 P

ower Exten

der

1900 Box

(4 Places)

PoExtender

PoWallplate

TOP

2 Gang Raised Cover

1900 Box

(4 Places)

TOP

2 Gang Raised Cover

PoWallplate

PoExtender

1

Leviton Mfg. Co., Inc. 59-25 Little Neck Pkwy • Little Neck, NY 11362-2591 • Tech Line: 1-800-824-3005 • Fax: 1-800-832-9538

Visit our Website at: www.leviton.com

JOB NAME:

JOB NUMBER:

CATALOG NUMBERS:

SPECIFICATION SUBMITTAL

Figure 2: Flush Mounting

MOUNTINGAll Power Extenders must have 4-1/2"spacing above and below each unit forproper ventilation and heat dissipation(refer to figure 3). Line voltage wiringshould be at least 6ft away from sound orelectronic equipment wiring. Mount PowerExtender to wall box with “TOP” facing upas follows: For Wall Box Mounting (referto figure 1), for Flush Mounting (refer tofigure 2) and for Panel Mounting (notshown), proceed as follows:a. The enclosure must be in accordancewith all local and national electrical codes.b. Leviton DOES NOT recommend using adoor to enclose the front of a panel, sincethis restricts airflow to the controls.c. If mounting multiple controls in anenclosure:• Ambient timperature within an enclosure“MUST REMAIN BETWEEN”32o-104oF(0o-40oC).• If not mounting in a metal enclosure, allunits “MUST” be mounted in a wall box.d. To improve heat dissipation of controls,remove the faceplate from the unit.

T

T

Minimum

Minimum

Figure 3: Front View Spacing

Figure 2: Flush Mounting

Figure 1: Surface Mounting

PE100-1 Power Extender

2.06(52.3 mm)

2.80

(71.

1 m

m)

4.72

(119

.9 m

m)

4.50(114.3 mm)

Extender

Controller/Dimmer

Hot (Black)

(Load)

Neutral (White)

(120VAC)

Ground

LOAD

Neutral

Load

Line

NE

UT

RA

L

NE

UT

RA

L

LO

AD

HO

T

HO

T

CO

NT

RO

L

Leviton Mfg. Co., Inc. 59-25 Little Neck Pkwy • Little Neck, NY 11362-2591 • Tech Line: 1-800-824-3005 • Fax: 1-800-832-9538

Visit our Website at: www.leviton.com © Copyright 2003 Leviton Manufacturing Co., Inc. All rights reseved. G-6723/G3

ProductSpecifications PE100-1.........................

Used if Dimmer/Switch has Neutral connection

Hot (Black)

(Load)

Neutral 2 (White)

Neutral 1 (White)

Line 1 (120VAC)

LOAD

Dimmer

Ground

Hot (Black)Line 2 (120VAC)

White

Load

Black

PowerExtender

NE

UT

RA

L

NE

UT

RA

L

LO

AD

HO

T

SW

ITC

HH

OT

CO

NT

RO

L

PowerExtender

D3206/08Controller/Dimmer

Hot (Black)

Hot (Black)

(Load)(Load)

Neutral (White)

Neutral (White)

Neutral (White)

Line (120VAC)

Line 1 (120VAC)

Hot (Black)Line 2 (120VAC)

Ground

LOAD 1

LOAD 2

Neutral

Load

Line

NE

UT

RA

L

NE

UT

RA

L

LO

AD

HO

T

SW

ITC

HH

OT

CO

NT

RO

L

PowerExtender

NE

UT

RA

L

NE

UT

RA

L

LO

AD

HO

T

SW

ITC

HH

OT

CO

NT

RO

L

Extender

Controller/Dimmer

Hot (Black)

Hot (Black)

(Load)

Neutral 2 (White)

Neutral 1 (White)

Line 1 (120VAC)

Line 2 (120VAC)

Ground

LOAD

Neutral

Load

Line

NE

UT

RA

L

NE

UT

RA

L

LO

AD

HO

T

HO

T

CO

NT

RO

L

Used if Dimmer/Switch has Neutral connection

Hot (Black)

(Load)

Neutral (White)

(120VAC)

LOAD

Dimmer

Ground

White

Load

Black

Extender

NE

UT

RA

L

NE

UT

RA

L

LO

AD

HO

T

HO

T

CO

NT

RO

L

Wiring Diagram 1B: Single Feed Wiring Application w/Dimmer

Wiring Diagram 1A: Single Feed Wiring Application w/Controller

Wiring Diagram 2B: Dual Feed Wiring Application w/DimmerWiring Diagram 2A: Dual Feed Wiring Application w/Controller

Wiring Diagram 3: Dual Feed Wiring Application w/Dimmer and Two Power Extenders

Single Feed WiringLine Hot can becontrolled by onecircuit breaker aslong as the totalload does notexceed the rating of the circuit breakers.

Single Feed WiringLine Hot can becontrolled by onecircuit breaker aslong as the totalload does notexceed the rating of the circuit breakers.

Dual Feed WiringThe Input controlcircuit and theOutput load circuitcan be supplied bytwo circuit breakerson a single phase or by two separate phases.

Dual Feed WiringThe Input controlcircuit and theOutput load circuitcan be supplied bytwo circuit breakerson a single phase or by two separate phases.

Dual Feed WiringThe Input controlcircuit and the Output load circuitcan be supplied by two circuitbreakers on a single phase or by two separatephases.

Note:Up to 4 PowerExtenders canbe Connectedtogether.

SPECIFICATIONS

Compatibility• For Box-Mounted Dimmers: Must use a

120V, 600W Incandescent version from the following families: IllumaTech™, Mural™, True Touch™, ToggleTouch™, TouchPoint™ and Home Controls

• For Monet™ installations, use a 120V, 600VA Monet Magnetic Low Voltage dimmer (requires a Neutral wire)

• For dimmers that include a Neutral wire (such as some scene-capabledimmers), the dimmer Neutral wire must be connected

• For Architectural Systems: Works with all families

ElectricalInput Voltage: 120V, 50/60HzLoad Rating: 1920W/VALoad Output Power: Phase independent of control deviceDimmer Input: 120V 50/60HzTesting/Code Compliance: UL Listed, CSA Certified and FCC Part 15

PhysicalColor: Aluminum clear anodized extruded heat sink with a snap-on molded white coverSize: 4.72"L x 4.5"W x 0.5"H (120mm x 114mm x 12.7mm)

EnvironmentalOperating Temperature Range: 0ºC to 40ºCStorage Temperature Range: -10ºC to 85ºCRelative Humidity: 20%-90% non-condensing

Warranty: Limited 2-Year Warranty