Operating and Maintenance Instructions ...€¦ · 1 SAFETYPRECAUTIONS PAGE 1.0R Revision:6 Date...

Operating and Maintenance InstructionsProgressing Cavity PumpSpectra

Please read the instructions first completely! · Do not throw away!The warranty does not cover damage caused by errors of the operator!

ProMinent Dosiertechnik GmbH · 69123 Heidelberg · GermanyTeile Nr. 986858 BA SP 003 07/12 EN

Imprint

Imprint:

Operating and Maintenance InstructionsProgressing Cavity PumpSpectra© ProMinent Dosiertechnik GmbH, 2005

Anschrift:

ProMinent Dosiertechnik GmbHIm Schuhmachergewann 5-1169123 Heidelberg · GermanyTelefone: +49 6221 842-0Fax: +49 6221 842-617

[email protected]

Subject to technical changes.

Page 2

TABLE OF CONTENTS PAGE0.0

Date Name Signed Revision: 2

issued 26.09.95 Mangel Substitute for issue

approved 27.09.95 Eitler of 18.03.94

released 28.09.95 Hantschktext no. 30100

copy to: 95

Page

1 Safety Precautions 1.0

2 Description 2.0

3 Packing, Transportation, Storage 3.0

4 Installation Instructions 4.0

5 Start-up 5.0

6 Temporary Shutdown 6.0

7 Maintenance 7.0

8 Trouble-Shooting and Remedying 8.0

9 Dismantling and Assembly of the Pump Housing 9.0

10 Dismantling and Assembly of the Rotating Parts 10.0

11 Removal and Fitting of the Connecting Shaft 11.0

12 Dismantling and Assembly of the Shaft Sealing 12.0

13 Recommended Stock of Wear Parts 13.0

14 List of Spares and Sectional Drawing 14.0

15 EC declaration of conformity 15.0

GB

Remark: Because of data transfer the text sheet printouts of our operatinginstructions do not contain a personal signature.

GB

Continued Page 1.0R

1 SAFETY PRECAUTIONS



approved 17.06.03 Denk of 31.10.96

released 17.06.03 Denktext no. 30700

copy to: 95

PAGE1.0

1 Safety Instructions

This manual contains basic instructions whichmust be observed when installing, operatingand servicing the machine / equipment. It isessential therefore for the user / installer orresponsible technician to read the manualthoroughly prior to installation and opera-tion.A copy of the manual must always be at handwhere the machine / equipment is being used.In addition to the general safety instructionslisted in this main section on safety, it is

necessary to observe the special safety rulesincluded in other sections of the manual, eg.for private use.

1.1 Safety Signs

The signs below are printed in the manual asgeneral hazard / danger symbols to markthose safety instructions whose non-obser-vance can result in danger to personnel or tothe machine / equipment. These signs are:

Hazard sign DIN 4844 - W9Danger to general public

Hazard sign DIN 4844 - W8Risk of electric shock

Risk of injury from machinery

Danger from suspended loads

Damage to machinery

Risk of injury to your eyes: goggles required.

GB

GB

1 SAFETY PRECAUTIONSPAGE1.0R

Revision: 6 Date Name Signed

Substitute for issue issued 16.06.03 Mangel

of 07.10.96 approved 17.06.03 Denk

text no. 30700released 17.06.03 Denk

copy to: 95

Warning plates located directly on the pump/equipment showing for example the correctdirection of rotation or the fluid connectionsused must always be observed and kept com-pletely legible.

1.2 Personnel Qualifications andTraining

Operating, maintenance, inspection andinstallation staff must possess the correct qua-lifications for their work. Areas of responsi-bility, scope of authority and staff supervi-sion must be exactly defined by the user. Ifpersonnel do not have the necessary know-ledge they must receive due training andinstruction. If necessary, the user of the ma-chine / equipment can arrange for such trai-ning and instruction to be provided by themanufacturer / supplier. The user must alsomake sure that the content of the manual isfully understood by the staff concerned.

Responsibilites

All work on and operation of the pump/equipment should be carried out by trained/competent and qualified operators, trades-men and / or engineers as appropriate.

Any person responsible for or in charge of

– working with lifting gear and ropes whenmoving a pump / equipment will have to beduly instructed prior to doing the transpor-tation job;

– mounting a drive to a pump / equipmentmust be qualified / trained as an industrialmechanic / technician;

– setting up installations into a plant must bequalified / trained as an industrial mechanic/technician and must be familiar with thedesign and functioning of the plant in whichthe pump / equipment is being installed;

– doing work on starting up, operation andmaintenance must gain knowledge of thepump / equipment principle prior to perfor-ming such works and must study the safetyinstructions and the manual thoroughly;

– doing repair works, and prior to doing suchworks, must be trained and skilled in the job.He must have due knowledge of the pump/equipments specific details set up in the repairinstructions. Unskilled personnel must betrained and repair works checked.

1.3 Dangers arising from Non-Observance of the SafetyInstructions

Non-observance of the safety instructions canresult in danger to personnel as well as to theenvironment and the machine. Non-obser-vance of the safety instructions can result inthe loss of claims for compensation.

Non-observance of the safety instructions canhave, for example, the following consequen-ces:

� Failure of essential functions of themachine / equipment

� Failure of mandatory maintenanceand servicing methods

GB

Continued Page 1.1R

1 SAFETY PRECAUTIONS PAGE1.1





copy to: 95

� Danger to personnel from electricity,machinery and chemicals

� Danger to the environment fromleakage of hazardous substances.

1.4 Safety Conscious Working

In addition to the safety instructions listed inthe manual, it is essential to observe thenational accident prevention directivescurrently in force and any of the users owninternal regulations concerning work andsafety.

1.5 Safety Instructionsfor the User / Operator

� If there is a risk of danger from any hotor cold machine component, the usermust fit protective guards to preventsuch components from being touched(according to Standard EN 563).

� Protective guards fitted to preventcontact with moving parts (eg.couplings) must be in position whenthe machine / equipment is in use.

� Leakages (eg. from a shaft seal) ofhazardous materials (eg. explosive,toxic, hot material) must bedischarged in such a way thatneither personnel nor theenvironment are placed at risk.Legal directives must be observed.

� All possible danger from electricity must

be eliminated (for details see eg. theregulations of your local power supplycompany).

1.6 Safety Instructions forMaintenance, Inspectionand Installation

The user must ensure that all maintenance,inspection and installation work is carried outby authorized and qualified personnel whounderstand the operating instructions andare adequately trained.

Work on a pump / equipment must only becarried out with the machine stopped andelectrical power supply turned off. The pump/equipment must not be under any pressureand must have cooled off. All proceduresdetailed in these operating instructions onthe stoppage of the machine must always beadhered to.

Pumps / equipment which convey harmfulmedia must be decontaminated.

Immediately after the maintenance work isfinished all safety devices and guards must bere-installed and the safety trips must betested.

Before putting the machine back into opera-tion the points detailed in section "Start-up"should be observed.

GB

GB

Continued Page 1.2






copy to: 95GB

1.7 Unauthorized Modifications andManufacture of Spares

Modifications or changes to machines / equip-ment are only permissible with the manu-facturer's agreement. Original spare partsand accessories authorized by the manufac-turer ensure safety.The use of other components revokes any lia-bility for consequences which may result.

1.8 Improper Application

Delivered machinery / equipment is only gua-ranteed safe for the use specified.

This machine / equipment was designed inaccordance with the prescribed conditions ofuse.The limits of use are laid down in the con-ditions of use and should in no way be ex-ceeded.

1.9 Specific Points for the Use of aSpectra Pump

A Spectra pump must be used for the pur-pose only for which it was sold.

If you change or wish to change the processmedium, you must check with either thesupplier or manufacturer that the pump issuitable for the new medium. This is espe-cially important with aggressive, poisonous orotherwise hazardous substances.

Pump criteria include:

1. Compatibility with the medium

2. Suitability for seal design / material,especially the shaft seal

3. Resistance to pressure and temperatureof the medium.

Please note that Spectra pumps are progres-sing cavity pumps and as such can generatevery high pressure.

A blockage or the chance closure of a valvein the discharge line can cause a pressure risemanifold as high as can be tolerated by theinstallation. This can result in the bursting ofpipes, which must be avoided especially inthe case of dangerous media.

Corresponding safety equipment musttherefore be installed, for example anemergency stop button, a pressure reliefvalve with return pipe or a bursting disc.

During maintenance and repair work on thepump please note the following:

1. Ensure that the pump drive can notbe turned on without authorization.

2. When opening the pump followthe instructions for handling themedium (eg. protective clothing,no smoking etc).

3. Before putting the pump back intooperation ensure that all guards andother safety devices (eg. drive–beltprotection, coupling protection) areproperly re–installed.

Continued Page 1.2R

1 SAFETY PRECAUTIONS





copy to: 95

PAGE1.2

GB

Always bear in mind your safety duringoperation, maintenance and installationof equipment. Please adhere to theEC-Directive for Machinery includingthe national regulations and follow theEuropean Standard EN 292 with theaccident prevention rules laid down bythe trade unions and other appropriatetechnical institutions.

GB

Continued Page 1.3






copy to: 95GB

1.10 Notes on Inspection and Repair

The legal regulations for safety at work,such as regulations for the workplace, regu-lations governing dangerous materials, acci-dent prevention, environmental protectioneg. regulations on disposal and water balan-ce obligate all commercial business to pro-tect their employees and / or people and theenvironment from adverse effects cau-sed by contact with dangerous mate-rials.

Important:

Inspection / repair of machinery and its partsonly takes place when a safety conformitycertificate has been completed by an

authorized and qualified specialist. Please usea copy and leave the original in the operati-on and maintenance manual.

Where special safety precautions are neces-sary in spite of careful emptying and clea-ning of the machinery, the necessary infor-mation must be given.

Machinery operating with radio-active mediawill only be repaired or inspected by one ofour specialist engineers under the safety ofthe owner.

The safety conformity certificate is part ofthe inspection / repair service. We reservethe right to refuse acceptance of this order /service for other reasons.

1 SAFETY PRECAUTIONS PAGE1.3





copy to: 95

Safety Conformity Certificate

The machinery and its accessories together with this safety conformity certificate relatingto repair / inspection services given to the undersigned by ourselves

Machine Type .......................................Number .......................................Delivery Date ....................................... Delivery Note No. .......................................

was carefully emptied and cleaned both inside and �� yesout in preparation for shipment �� no

Special safety precautions with regard to health or �� necessarymedia endangered by water are to be implemented �� unnecessary

The machinery is set up to transport materials dangerousto health or water and came in contact with �� yesmedia containing harmful substances �� no

The following safety precautions are necessary with regard to irrigation media, overflow liquid and waste management:

.................................................................................................................................................

.................................................................................................................................................

We confirm that the above mentioned details are correct and complete and thatdespatch will follow in accordance with the legal requirements:

Company Telephone .............................................

........................................................................... Fax .............................................

........................................................................... Telex .............................................

Address

...........................................................................

...........................................................................

Name ............................................................. Position .............................................

....................................... ............................................. Date Company Stamp / Signature

GB

GB

NN EE MM OO

PP

UU MM PP EE

NN

Continued Page 2.0R

2 DESCRIPTION AND GENERAL DATA PAGE2.0



approved 04.08.98 Hantschk of 18.03.94


copy to: 95

2 Description

The Spectra pump is a progressing cavitypump.The main components which determine thesystem discovered by Professor René Moineauare a rotating part, called the rotor and a sta-tic part, called the stator.The rotor is a helical screw with an extreme-ly large pitch, large thread depth and smallcentre diameter with round cross-section for1/2-geometry and elliptical cross-section for2/3-geometry. The stator has a two start orresp. 3 start thread and is double or resp. 1.5the pitch length of the rotor. This providesspace for the medium between the rotor andstator. When the rotor turns round inside thestator the medium moves continuously fromthe inlet to the outlet.

The universal Spectra pump system unifiesmany positive characteristics of other pumptypes:

� Like centrifugal pumps Spectra pumps haveno suction or pressure valves, but do have astable flow rate in proportion to the numberof revolutions.

� Like piston pumps Spectra pumps have asuction capability of up to 8.5 m vacuummetric.

� Like membrane and peristaltic pumps theSpectra pump can transport every type ofinhomogenous, gaseous and abrasive media,as well as those that are not of a liquid con-sistency or contain solids and/or fibrous mate-rial.

� Like gear pumps and screw pumps theSpectra pump is capable of coping with highmedium viscosities.

� Like piston, membrane, gear or screwpumps the Spectra pump can perform dosingoperations.

Length and cross-sections through the rotorand stator with 1/2-geometry during arotation.

0°/360°KK

90°

180°

270°

Rotor-StellungSTATOR

ROTOR

GB

Rotorposition

GB

MarchioniniRechteck

MarchioniniRechteck

2 DESCRIPTION AND GENERAL DATAPAGE2.0R




text no. 30700released 06.11.98 Hantschk

copy to: 95

2.2 General Data

Noise emissions:

The maximum permitted noise emission level at a work place is 70 dB (A).

The noise level was measured in accordance with DIN Standard 45635-24-01-KL2 to assure that the pump does not exceed 70 dB (A).

Noises generated by the drive and pipes are not included in the aboveemission value.

A prerequisite for the noise emission level of ≤ 70 dB (A) is that the pump is operated in a cavity free regime and is bolted to a concrete base.

GB

Length and cross-sections through the stator with rotor with reduced stator wall thickness

1/2-geometry

2/3-geometry





copy to: 95

NN EE MM OO

PP

UU MM PP EE

NN

Continued Page 3.0R

3 PACKAGING, TRANSPORTATION, STORAGE PAGE3.0

3 Packaging, Transportation, Storage

3.1 Packaging and Transportation

The packings are labelled and symbols give the handling instructionsin accordance with DIN 55402.On receipt check for any transport damages. Transport damages should be reported to the transporter immediately.The pumps should be transported as closely as possible to the location of installation and only there should they be uncrated.

Uncrated horizontal pumps should be lifted by using a shackle which can be attached to the baseplate. The bolt holes of the frame or the lifting lugs attached to the baseplate could be used as shown on the installation drawing.

Vertical pumps should be lifted by using the bolt down holes,lifting lugs or shackles attached to the baseplate. This is shown onthe installation drawing. For most applications, the drive is mountedon top of the pump.

Be careful when lifting top heavy pumps. The centre of gravity may beabove the points where the lifting gear is attached to. If the case, secure additionally against tipping over!

Vertical pumps should not be deposited unless they are secured vertically.Hazards of tipping! Deposit only in horizontal position!

It is essential to avoid that the total pump unit be suspended witheye bolts of the motor or gear box. These eye bolts should be used for lifting the motor and/or the gear box only.

The Accident Prevention Rules, Section 18.4 relating to lifting accessories for the lifting of loads (VBG 9a) must be strictly adhered to.

Because of the variety of possible pump designs and applications, only general instructions can be given here. These should be good enough for experienced assemblymen or transportation experts.When in doubt, please ask for detailed information on the pump unit concerned.

GB

GB

3 PACKAGING, TRANSPORTATION, STORAGE

Continued Page 3.1

PAGE3.0R





copy to: 95

When moving the pump or unit on wheels strictly attend to the following:

� Pad lock the motor drive and secure against unintended starting up.

� Move the pump unit carefully and slowly, especially where the ground is uneven. Hazards of tipping!

� Ensure a stable position of the pump or unit at the operating /storage place and secure it by actuating all clamping devices on all the wheels or rollersagainst voluntary moving away.

� Where fitted loosely, carefully watch the pipe bends when pumping.Power of repulsion!

� Where necessary, secure the pump unit additionally with support blocks.

3.2 Storage

The pumps are preserved for transport unless specified otherwise.In cases of longer storage the pumps should be handled as follows until installation:

� Stator:

If the pump is not to be used immediately, then the elastomer along the contact line between rotor and stator may become permanently distorted (compression-set). This will increase the break away torque. Therefore, the stator should be removed and kept separately in a clean, cool and dry environment. Standard DIN 7716 summarizes detailed information on the storage of rubber products, some of which is gathered here, and the following notice applies to a storage for a period of up to six months.

General

Most of the rubber products may change their physical properties under unfavourable conditions or if treated improperly, which will result in a shorter lifetime. Or they may become useless through excessive hardening, aging, regenerating or permanent deformation, also because of blistering, cracking or other damages appearing on the surfaces. The changes may occur under the influence of oxygen, ozone, heat, light, humidity, solvents or because of storing the products under tension. If stored and treated properly, the rubber products will keep their properties, even over a long period of time (some years), almost unchanged. This does, however, not apply to uncured rubber compounds.

GB

Date Name Signed Revision:


approved 24.06.98 Denk of


copy to: 95

NN EE MM OO

PP

UU MM PP EE

NN

3 PACKAGING, TRANSPORTATION, STORAGE PAGE3.1

Store room

The environment in which rubber products are being kept must be cool, dry, free of dust and rather airy, and they must not be stored in the open, not even in a weather sheltered space. Rubber products should be kept in surroundings not having less than minus 10 °C and not more than plus 15 °C. Store rooms should not be damp, and it must be ensured that there will be no condensation. Most favourable is an environment offering a relative humidity under 65 %. Rubber products must be protected against light, particularly direct sunlight or artificial light when having a high UV portion. They should furthermore be kept away from ventilation, especially draught, by wrapping them up. As ozone is very aggressive and harmful there should be no store room used which houses equipment likely to produce ozone, e.g. electric motors or other equipment which might bring about sparks or other electrical discharges. There must be no solvents, oil, grease, lubricants or any chemicals kept in a store room.

� Rotor

Please support with wooden blocks and cover up against harm from mechanical impact.

� Pump parts in stainless steel

No grease coating necessary.

� Other, non-coated pump parts

Protect with grease.

� Drives

Please observe the drive supplier's instructions.

GB

GB





copy to: 95

NN EE MM OO

PP

UU MM PP EE

NN

Continued Page 4.0R

4 INSTALLATION INSTRUCTIONS PAGE4.0

4 Mounting and Installation If the Spectra pump was stored and the rotor grease protected:Remove the grease before installing the stator.Clean the rotor thoroughly in order to avoid unsuitability of the grease with the stator material and the pumping medium.

Screw the pump at all fixing points (bearing housing / drive stool, end stud, support feet) using all fixing bores securely down to the sub-structure (ground plate, machine frame, foundation etc.).

4.1 Direction of Rotation

The direction of rotation of the pump is given on the model plate and in the order confirmation. The direction of delivery of the Spectra pump is a function of the direction of rotation.

Changes must be agreed upon and confirmed by the supplier.

4.2 Pressure

The maxiuml permissible pressure inside the pump housing (A) and the maximum permissible pressure inside the end stud (B) can be seen in the following table:

4.3 Piping System

� Arrange suction and pressure pipes so that when the pump is not running, the medium is still present before and after the pump. Sufficient media should remain inside in order to lubricate the pump during restart.

GB

GB

Spectra pressure A pressure B

12/1 – 12/105 12 bar 12 bar

6/300 – 6/600 6 bar 6 bar

5/1400 5 bar 5 bar 5 bar

3/3000 – 3/12000 3 bar 3 bar

4 INSTALLATION INSTRUCTIONS

Continued Page 4.1

PAGE4.0R

Revision: Date Name Signed


of approved 20.06.03 Denk


copy to: 95

� The installation of a removable distance piece between the end flange (B)and the pipe work is recommended in order to make the dismantling ofthe stator easy. The distance piece (see sketch) needs to have a minimum "ABL" disassembly length the values of which are shown in the table below.

Disassembly length ABL in mm:

GB

B A

STATOR

ABL

Spectra minimum disassembly length

12/1 – 12/105 130 mm

6/300 – 5/1400 160 mm

3/3000 230 mm

3/6000 310 mm

3/12000 430 mm

Continued Page 4.1R

4 INSTALLATION INSTRUCTIONS PAGE4.1





copy to: 95

� Clean the pipe work and rinse thoroughly before installing the pump.

� Connect the pipe work ensuring that no external stress attacks the pump body. The installation of compensators between the pump and the pipework is recommended:

– No risk of damage to the pump housing from pipelines "resting" on the pump.

– No risk of damage to the pump housing through vibrating pipelines.

� The twisting loads (Fx, Fy, Fz) and bending loads (Mx, My, Mz) permitted to be put on the suction/discharge flange comply with the requirements of API 676 and exceed the requirements of EN ISO 14847. They are shown in the table below.

*) Screwed joints must not be charged with loads which may result in tightening or loosening these joints

GB

x

x

y

y

z

zDN

DN

GB

Spectra Standard Fx, Fy, Fz Mx, My, Mznominal diameter N Nm*

DN

12/1 – 12/105 G 1/2” 170 85

6/300 – 3/3000 G 11/4” 550 300

3/6000 50 780 420

3/12000 65 990 530

4 INSTALLATION INSTRUCTIONSPAGE4.1R





copy to: 95

4.4 Electrical Connection

All work relating to electricity shall only be made by authorized and qualified personnel and it should be in compliance with the requirements of the relevant national regulations!

In particular for control systems should the latest version of the EC-Directive for Machinery 98/37/EEC, Annex I, Section 1.2 Controlsbe carefully observed!

Note for frequency converter operation: It is absolutely necessary to connect the PTC-resistors of the drive in case of frequency converter operation to protect the drive against overheating.

GB

NN EE MM OO

PP

UU MM PP EE

NN

5 START-UP PAGE5.0





copy to:

5 Start-up

The Spectra pump design requires strict attention to the following:

Never run the Spectra pump dry!A few rotations in dry conditionwill damage the stator!

� Before starting up for the first time, fill the pump with medium.In the case of high viscosity media fill with a liquid.Pump priming is vital to ensure lubrication of the rubber stator.Fill the piping on the pump suction side.In anti–clockwise rotation only: Fill the pump housing.

The Spectra pump is a progressing cavity pump which can produce pressures that may cause the bursting of vessels or pipes.

The power transmission train (shaft, coupling rod, joints, rotor)of the pump may be overloaded thus resulting in damage or breakage.

Also the pump housing parts with their connections may be overloaded and break. There is a table in Section 4 of these Maintenance and Operating Instructions showing the pressure resistance of the pump housing parts.

Never run the pump against a closed inlet or outlet valve!

� Open valves and vents before starting the pump!

� Check the direction of rotation by briefly switching on the pump motor.

GB

GB

NN EE MM OO

PP

UU MM PP EE

NN

6 TEMPORARY SHUTDOWN PAGE6.0





copy to: 95

6 Temporary Shutdown

� After stopping the pump empty and if necessary rinse it if

– the medium might freeze due to the temperature surrounding the pump. Especially where there is a danger of frost if the pump is installed outside a building

– the medium tends to solidify or harden

– the medium tends to glue up the shaft seal.

� Stator:

When stored for a long period, the elastomer along the contact line between the rotor and stator may become permanently distorted (compression-set).This will increase the break away torque. For this reason, the stator should be removed (please observe Section 9!), and stored in a cool, dry place in air tight package to give protection against light and air.

� Rotor:

Support the rotor on wooden blocks and cover to protect it from mechanical damage, after the stator has been removed.

� Stand-by pump:

A stand-by pump is sometimes used as a back-up for the main pump and, when standing idle for longer periods, should be operated from time to time. The pump may otherwise become seized when being started up. This is due to compression set i.e. distortion of the stator against the surface of the rotor.

GB

GB

NN EE MM OO

PP

UU MM PP EE

NN

7 MAINTENANCE PAGE7.0





copy to: 95

7 Maintenance

7.1 Pumps in General

� The pumps should be regularly rinsed or cleaned if deposits of medium are likely to build up (sedimentation).

If the pump needs to be opened to do this, ensure that the pumpand motor are switched off and cannot be turned on accidently(eg. by removing the fuse).

Periodical standstill to allow for cleaning during operation depends on themedium and type of operation.

� The pump can be cleaned:

– through the cleaning ports provided in the pump housing

– manually by dismantling the pump.

GB

GB

NN EE MM OO

PP

UU MM PP EE

NN






copy to:

7.2 Lubrication

The Spectra pump does not require frequent lubrication.

� Maintenance of the drive should be carried out accordingto the drive manufacturers instructions.

� Maintenance– where no manufacturers instructions are available and– when normal conditions of use exist:

– Strip down the drive unit– Remove the bearings– Clean all parts– Renew the lubricant

every 5000 operating hours or at least every two years.

Special lubricants are often specified for mechanically controlled variable speed drives.It is therefore important to follow the drive manufacturersmaintenance instructions.

GB

GB

Continued Page 7.2R





copy to:


7.3 Lubricating the Pin Joints with SM-Pin Joint Seals

� It is advisable to change the oil and check the seals of the pin joints:

– when renewing worn joint parts

– when opening the pump for any reason.

The quantity of oil added per pin joint isa function of the joint external diameter D:

GB

D

8235

Joint external Quantity of oilSpectra diameter D per joint

in mm in cm3(see sketch)

12/1 - 12/105 25 1

6/300 - 5/1400 28 1,5

3/3000 30 2

3/6000 40 5

3/12000 54 15

GB

7 MAINTENANCEPAGE7.2R





copy to: 95

Lubricating Oil:

GB

Designation permitted productDIN 51502

CLP 460 SHELL Omala 460

CLP PG 320 KLÜBERSYNTH GH 6-320

7.5 Shaft Sealing through Single Mechanical Seal

There are various constructions of mechanical seals. Especially advantageous is the use of standard mechanical seals according to DIN 24960. These seals have regardless of their brand the same fitting dimensions which makes them interchangeable.Mechanical seals with a coil spring can only be used for pumps which are run in one direction of rotation.

� The seal specification of a Spectra pump is recordedon the order confirmation sheet.

� Pumps fitted with direction dependent seals should never be run in the opposite direction ofthe rotation arrow.

� If excessive leakages occur the spring tension and the seal surfaces should be checked, and the seal be replaced, if necessary.

Single mechanical seals usually work without any additionalequipment.

NN EE MM OO

PP

UU MM PP EE

NN






copy to: GB

GB

NN EE MM OO

PP

UU MM PP EE

NN

Continued Page 8.0R

8 TROUBLE-SHOOTING AND REMEDYING PAGE8.0





copy to: 95

8 Trouble-Shooting and Remedying

8.1 Trouble Chart

The chart overleaf lists possible problems

– the type– the likely reason / cause– the remedy.

� A problem may have various causes: Several boxes in the verticalcolumn are marked with a cross.

� A reason / cause may result in various problems:Several boxes in the horizontal column are marked with a cross.

8.2 How do you trace the kind of problem to find the possible cause ?

– The column describing a possible problem shows one or severalboxes marked with a cross.

– On the corresponding lines you will find the possible reasons / cause and some hints how to handle the problem .Thus the actual cause of the problem can be narrowed down andeventually detected.

– If you find further cross-marked boxes on one of the linesand should there appear corresponding problems as well,then the likely cause of the problem has been detected.

� The table helps in finding the root of the problem and will give you the remedy if it is straight forward. For more complicated problems the manufacturer has to be consulted.

GB

GB

The

pu

mp

is n

o lo

ng

er s

tart

ing

The

pu

mp

is n

o lo

ng

er s

uck

ing

The

pu

mp

ed m

ediu

m is

to

o li

ttle

The

pre

ssu

re is

to

o lo

w

The

pu

mp

ed m

ediu

m is

un

stab

le

The

pu

mp

is r

un

nin

g lo

ud

ly

The

pu

mp

is s

tuck

The

dri

ve is

ove

rlo

aded

The

stat

or

life

tim

e is

to

o s

ho

rt

The

roto

r lif

e ti

me

is t

oo

sh

ort

The

shaf

t se

al is

leak

ing

Possible Problems

In new pumps or stators : the static friction is too great.

The pump electrical equipment is not compatible with the electrical supply.

There are foreign bodies in the pump.

The stator has swollen, the elastomer is not compatible with the medium.

The liquid medium sediments or hardens when left to stand.

The suction pipe is leaking.

The rpm is too low.

The suction is too great or pressure too low (cavitation).

The stator is worn out, or temperature of liquid is too low.

The rotor is worn out.

The pump and drive are not axially aligned.

The roller bearings are destroyed.

The viscosity is too high.

The stuffing box is incorrectly tightened.

Mechanical seal : rotation is incorrect.

Mechanical seal : elastomers damaged, swollen or brittle.

The pressure is too high.

The temperature of the liquid medium is too high, the stator is too ductile.

The solids content of the medium is too high and leads to blockages.

There is air in the suction pipe.

The shaft seal is leaking.

With reduced diameter rotors : operating temperature has not been reached.

The pump is running dry.

The stator material is brittle.

The joints are worn out.

The elastic element of the coupling is worn out.

The rpm is too high.

The specific weight of the medium is too high.

The packing is not suited to the liquid medium.

Mechanical seal : mechanical seal and mating ring have failed.

Possible Causes ( Remedy overleaf)



of approved 21.09.95 Eitler


copy to:GB

Replace elastomers. Check whether the liquid medium agrees with order details, if necessary change material.

NN EE MM OO

PP

UU MM PP EE

NN

8 TROUBLE-SHOOTING AND REMEDYING PAGE8.1



approved 19.10.95 Hantschk of 22.09.95


copy to: 95

Fill the pump up, then pump through manually using a suitable appliance; if necessary use glycerine as lubricant in the stator.

Check order information. Examine electrical installation (possibly 2 phase operation).

Remove foreign bodies and eliminate possible damage.

Check whether the liquid medium agrees with the order requirements. Possibly change stator material..

Clean the pump and rinse through after each run.

Check seals and tighten pipe connections.

In the case of adjustable drives : increase the rpm. If necessary change the drive.

Decrease suction resistance, lower the temperature of the liquid medium, install the pump at a lower location.

Replace with a new stator or ensure correct liquid temperature.

Change rotor, establish the cause. Wear and tear, corrosion, cavitation; if necessary change to a different material or coating.

Re-align the unit.

Replace roller bearings, lubricate, reseal. At higher temperatures observe the lubricant and the bearings.

Measure the viscosity and compare with order details. If necessary adjust viscosity or change the drive.

Service stuffing box according to page 7.4, if necessary renew worn shaft.

Change electrical connection.

Measure the pressure with a manometer and check against order details. Reduce the pressure or change the drive.

If the liquid medium temperature cannot be lowered, use a reduced diameter rotor.

Increase the liquid part of the medium.

Increase the suction liquid level, prevent turbulance and air bubbles at the inlet.

Stuffing box : tighten or renew. Mechanical seal : renew seals, eliminate solid deposits.

Warm up the pump (stator) to operating temperature first of all.

Fill up the pump, provide for dry running protection, move the pipes.

Fit a new stator. Check the liquid medium agrees with order details; if necessary change the stator material.

Replace relevant parts, carefully reseal and lubricate.

Use a new connection and re-align the pump.

In the case of adjustable drives : lower the rpm.

Measure specific weight and compare with order details. If necessary adjust specific weight or change the drive.

Replace fitted packing with another packing type.

Replace relevant rings with new ones.

Remedy

GB

GB

NN EE MM OO

PP

UU MM PP EE

NN

Continued Page 9.0R

9 DISMANTLING AND ASSEMBLYOF THE PUMP HOUSING

PAGE9.0





copy to:

9 Removal and Fitting of End Stud, Stator and Pump Housing

The pump with attached pipework should be empty and must have cooled off!Disconnect the pipework on the suction side and pressure side of the pump.

Dismantling Spectra 12/1 - 12/105

� Remove the hex nuts (2030) with spring washers (2025).

� Take off the retaining plate (2555).

� Remove the end stud (2005) from the stator (3005).

� Pull the stator (3005) out forward.

� Pull the pump housing (2010) off from drive stool (0085) or bearing housing (0005).

Refitting is a simple reversal of this procedure.

� Engaging the stator (3005) and rotor (1999) will be easier when using glycerine as a lubricant.

� Ensure during refitting that gasket (8110) is in perfect conditionand will sit properly.

GB

GB


Continued Page 9.1

PAGE9.0R





copy to:

3010

3020

2010

B

Support pump housing (2010) and stator (3005) withwooden blocks.

Loosen the hex nuts B (3020), where fitted, andremove the thru bolts (3010).

�

Where fitted, remove the second support foot(2035/2) and the washers (3070).

�

�

GB

2035/2

3070

3005

2035/1G

2035/2

2035/1

2005

3020

3015

A

3070

Dismantling Spectra 3/3000 - 3/12000

Remove the securing screws (S) from support feet(2035) to baseplate (G).

Unscrew the hex nuts A (3020) and remove withspring washers (3015), then withdraw the end stud(2005) and first support foot (2035/1) with washers(3070).

�

�

S

NN EE MM OO

PP

UU MM PP EE

NN

Continued Page 9.1R


PAGE9.1





copy to:

Remove the hex nuts (2030) with spring washers(2025).

Pull the pump housing (2010) off forward.�

�

3005 1999Caution for pumps with tubular rotors:

Where the walls of tubular rotors are worn in thewear zones, pumping medium may occur inside therotor and may come out when pulling off thestator. Ensure that protective measures have been takenwhen pumping dangerous media!

Pull the stator (3005) out forward.A stator extractor can be supplied as specialaccessory.

�

1/2 ge

ometry

GB

2010199920302025

E

A

B

D

8005

20052010

Assembly

Refitting is a simple reversal of this procedure.

When refitting the stator (3005) check direction ofstator (3005) is correct! The funnel-shaped inflowside (E) of the stator (3005) must show to

– the pump housing (2010) when rotation is anti-clockwise

– the end stud (2005) when rotation is clockwise

when viewed on pump shaft end.

Elastomer stators (A) have integrated front sidesealing profiles (D). They don't need additional gas-kets for sealing off the end stud (2005) and thepump housing (2010).

�

�

GB


PAGE9.1R





copy to:

Be careful when engaging the stator (3005) androtor (1999). Do not trap your fingers! Do not reach inside the stator!

Push the stator (3005) with a rotating movement onto rotor (1999). Apply an assembly device and some glycerine toease engaging the stator (3005) and rotor (1999).

�

3005 1999

GB

Fastening the end stud (2005):

Screw the hex nuts C (3020) down into the thru bolts(3010) as far as possible.Slip on the first washers (3070), the support foot(2035), the second washers (3070), the end stud(2005) and tighten with spring washers (3015) andhex nuts A (3020).Finally, fasten the support foot (2035) from behindwith the two hex nuts C (3020).

When tightening hex nuts (2030) a gap will remain between drive stool (0085) and pump housing (2010).

Please do not try to close this gap by overtightening the nuts! Drive stool (0085) may break!

Torque values for hex nuts (2030):

�

�

2005 30103020

3015 3070

2035

A C

Ensure during refitting that the O-ring (8015) or, where a heating jacket (3025) is installed, the O-rings (8030) are in perfect condition and will sit correctly.

Ensure that the drain plug (2015) is not screwed too tightly into the pump housing (2010), since otherwise its conical thread may break the pump housing (2010). The torque should be about 40 - 50 Nm.

Size M6 M8 M10 M12 M16 M20 M24 M30

Requiredtorque 8 15 30 45 75 80 100 120Nm

Continued Page 10.0R

10 DISMANTLING AND ASSEMBLYOF THE ROTATING PARTS

PAGE10.0

date name signed revision:

issued 24.06.03 Mangel substitute for the issue

approved 25.06.03 Denk dated


copy to:

10 Dismantling and Assembly of the Rotating Parts(Spectra 3/3000 - 3/12000)

10.1 Removal of Rotor and Coupling Rod

For removal of the rotor (1999) and coupling rod (1998) the pin joints should be dismantled as follows:

Place the dismantled unit – consisting of drive stool(0085) with drive (A) and connecting shaft (1050),coupling rod (1998) and rotor (1999) – on the work-bench with a wooden block supporting the rotor(1999).

Push circlip (5065) out of its groove and slip off overthe head of rotor (1999 or connecting shaft (1050).

If necessary hit the edge of sleeve (5115) at an anglewith the help of a wooden block and a plastic ham-mer. Taking care not to damage the O-rings (8060)!

�

�

�

50651050, 50551999, 5056

GB

511510501999 8060

1999 10500085 A1998

GB

Continued Page 10.1


PAGE10.0R

revision: date name signed

substitute for the issue issued 24.06.03 Mangel

dated approved 25.06.03 Denk


copy to: 95

Press the pin (5075) out of the head of rotor (1999)or connecting shaft (1050). If necessary use a ham-mer and a thin cylindrical pin (DIN 6450 C).Drain the oil into a receptacle.

Please dispose of this oil in the proper manner.

Using a screwdriver, carefully lever the SM-pin jointseal (8235) out of the head of rotor (1999) or connec-ting shaft (1050).

Taking care not to damage the SM-pin joint seal(8235)!

Pull apart the rotor (1999)/ coupling rod (1998) /connecting shaft (1050) assembly. Remove the O-rings (8060).

Push the SM-pin joint seal (8235) towards the headof coupling rod (1998). In the narrow coupling rodsection press the clamp ring (5425) out of thegroove of the seal. Then slip the SM-pin joint seal(8235) and clamp ring (5425) off over the head of thecoupling rod (1998).

�

�

�

�

1998 8235 8060

10501999

10501999

5075

1998 806010501999

5425 8235 1998

GB



PAGE10.1





copy to:

10.2 Fitting the Rotor and Coupling Rod

For fitting the rotor (1999) with coupling rod (1998),the two pin joints should be assembled as follows:

Slip the clamp ring (5425) over the head of couplingrod (1998).

Push the SM-pin joint seal (8235) over the head ofcoupling rod (1998) towards its narrow section, theresqeezing the clamp ring (5425) into the groove ofthe SM-pin joint seal (8235).

Push the SM-pin joint seal (8235) with the correctlyplaced clamp ring (5425) up to the shoulder ofcoupling rod (1998).

5425

5425

1998

1998

8235

8235

8235

1998

�

�

�

GB

GB

Continued Page 10.2


PAGE10.1R



dated approved 25.06.03 Denk


copy to:

Slip the circlip (5065) on to the coupling rod (1998).Slide the sleeve (5115) on to coupling rod (1998) sothe inside diameter of chamfering (A) is being pla-ced towards the coupling rod (1998) extension.Chamfering (A) will later on ease the installationover the O-rings (8060).Orient the head of coupling rod (1998) until it is invertical position for the bore (B) for the pin (5075).

Slide the coupling rod (1998) with SM-pin joint seal(8235) into the bore of rotor (1999) or connectingshaft (1050) and insert the pin (5075) from below andpush up to the upper edge of coupling rod (1998).Support the pin (5075) against dropping out.Slide the SM-pin joint seal (8235) into the rotor(1999) or connecting shaft (1050) only from below,and in a slightly slanted position.

For lubrication, use an oil can which should befitted with a thin plastic hose having an outside dia-meter of not more than 4 mm.Insert this hose into the upper oil port opening inthe rotor (1999) or connecting shaft (1050). Thenslide the hose end past the coupling rod (1998)all the way down to the bottom section of the rotorhead (1999) or connecting shaft (1050).Slowly fill with lubricating oil up to the filling port.

Pull the hose out.Then insert the hose end through the small gap onthe topside of SM-pin joint seal (8235) and guide itdown to the bottom of the hollow space betweencoupling rod (1998) and SM-pin joint seal (8235).Slowly fill with lubricating oil up to the gap.

�

�

�

�

5065

1998

1998

1998

8235 5075

5075

8235 5075

10501999

10501999

5115

A B

GB


PAGE10.2





copy to:

Slip the sleeve (5110) or (5115), with its chamfering(A) forward, on to the head of rotor (1999) orconnecting shaft (1050) and push up to the shoul-der.

Pull the hose out.Push the pin (5075) entirely into the bore of headof rotor (1999) or connecting shaft (1050) and retainin place.Only now, press the SM-pin joint seal (8235) intothe bore of head of rotor (1999) or connecting shaft(1050) and push up to the shoulder. In doing so theSM-pin joint seal (8235) should be slightly bulbousaround the outer surface. Wipe off overflow oil. Usethis oil for lubricating the O-rings (8060).

Place the circlip (5065) into its groove on the rotorhead (1999) or connecting shaft (1050) and careful-ly snap in place all around.

Drive connecting shaft (1050), coupling rod (1998)and rotor (1999) are now joined by means of the twopin joints.Pump housing (2010), stator (3005) and end stud(2005) may now be fitted.

5075

1998 8235

5115

5065

�

�

�

�

10501999

10501999

10501999

GB

1999 10500085 A1998

GB



PAGE10.3

date name signed revision: 4


approved 23.05.95 Eitler dated 04.05.95


copy to:

10.3 Dismantling and Assembly of the Rotating Parts(Spectra 12/1 - 5/1400)

For removal and refitting of the rotor (1999) and coupling rod (1998)the pin joints should be dismantled and re-assembled as follows:

Dismantling:

Push the SM-pin joint seal (8235) away from therotor (1999), drive shaft (1005) or connecting shaft(1050) so the bore for the pin (5075) comes free.

Press the pin (5075) out of the rotor (1999),connecting shaft (1050) or drive shaft (1005). Then withdraw the coupling rod (1998) from thebore of rotor (1999), connecting shaft (1050) or driveshaft (1005).

Push the SM-pin joint seal (8235) towards the headof coupling rod (1998). In the narrow coupling rodsection press the clamp ring (5425) out of thegroove of the seal. Then slip the SM-pin joint seal(8235) and clamp ring (5425) off over the head of thecoupling rod (1998).

�

�

�

5075

8235

19991005, 1050

199910051050

8235

1998

19985425

GB

GB


PAGE10.3R

revision: 3 date name signed


dated 23.02.95 approved 03.05.95 Eitler


copy to:

Re-Assembly:

Slip the clamp ring (5425) and the SM-pin joint seal(8235) on over the head of the coupling rod (1998).

Push the SM-pin joint seal (8235) towards thenarrow section on the head of coupling rod (1998)and place the clamp ring (5425) back into thegroove of the SM-pin joint seal (8235).Then move the SM-pin joint seal (8235) up to thecoupling rod (1998) shoulder.

Place the head of coupling rod (1998) into the boreof the rotor (1999), drive shaft (1005) or connectingshaft (1050).

Join the rotor (1999), drive shaft (1005) or con-necting shaft (1050) and coupling rod (1998) by thepin (5075).Then push the SM-pin joint seal (8235) up to theshoulder of the rotor (1999), drive shaft (1005) orconnecting shaft (1050).

Re-assemble the second pin joint in the samemanner.

�

�

�

� 5075

8235 1998

8235 19985425

199910051050 1998

8235 19985425

GB


PAGE10.4





copy to:

10.4 Replacing the Wear Sleeves of Adapter, Rotor and Coupling Rod

The wear sleeves (5435, 5440) have a very tight fit.A press should be used to remove or refit them.

It may be possible though to drive the damagedsleeves out with a suitable mandrel. A rigid vicehowever is needed at the least for pressing newsleeves (5435, 5440) in again.

Orient the wear sleeves (5435) so that their ovalbore agrees with the longitudinal axis of thecoupling rod (1998).

Generously oil the wear sleeves (5435, 5440).

Every wear sleeve (5435, 5440) has got one smallerouter diameter on one end for better insertion intothe bores of the coupling rod.

Ensure the sleeves are placed in the correct orien-tation to the coupling rod (1998).

1998

5435 5440

1998

5435

�

�

�

GB

GB

NN EE MM OO

PP

UU MM PP EE

NN

11 DISMANTLING AND ASSEMBLY OF THE CONNECTING SHAFT

PAGE11.0





copy to:

11 Removal and Fitting of the Connecting Shaftwith Shaft Seal (Spectra 6/300 - 3/12000)

Removal:

� Push the circlip (1035) in the direction to the mechanical seal.

� Remove pin (1030).

� Remove the shaft seal housing (7005) and mechanical seal (7010) together with connecting shaft (1050) and set ring (1035) from drive stool (0085) and the drive shaft. The thread of cylindrical head screw (1040) can be used as forcing screw.

� If a mechanical seal is installed, see description"Removal and Fitting of Mechanical Seal" after Page 12.0.

Fitting:

� Apply grease into the bore of the connecting shaft (1050) to avoid rust (e.g. TCE-Metallic 600).

� Assemble the shaft seal housing (7005) and mechanical seal (7010) together with connecting shaft (1050) and set ring (1035) with drive stool (0085) and push connecting shaft (1050) on to the drive shaft. At this please observe the installation direction of set ring (1035) (please see mark).

� If a mechanical seal is installed, see description"Removal and Fitting of Mechanical Seal" after Page 12.0.

� Connect the connecting shaft (1050) and the drive shaft by pin (1030). Push set ring (1035) on pin (1030).

GB

GB

11 DISMANTLING AND ASSEMBLY OF THE CONNECTING SHAFT

PAGE11.0R



dated approved 03.05.95 Eitler


copy to: GB

11 Removal and Fitting of the Connecting Shaftwith Shaft Seal (Spectra 12/1 - 12/105)

Removal:

� Remove pin (1055).

� If the shaft seal housing (W) is connected tightly to the drivestool (0085), then pull off the connecting shaft (1050) from the drive shaft.If the shaft seal housing (W) is a separate part,then take it out ofthe drive stool (0085) together with the connecting shaft (1050).

� Removal and Fitting of Mechanical Seal after Page 12.0.

Fitting:

� Apply grease into the bore of the connecting shaft (1050) to avoid rust.

� If the shaft seal housing (W) is connected tightly to the drivestool (0085), then insert connecting shaft (1050) into the shaft seal housing (W) and push connecting shaft (1050) on to the drive shaft.If the shaft seal housing (W) is a separate part, then place it intothe drive stool (0085) together with the connecting shaft (1050) and push connecting shaft (1050) on to the drive shaft.

� Removal and Fitting of Mechanical Seal after Page 12.0.

� Apply some grease into the pin (1055) also, or oil, and fit in.

NN EE MM OO

PP

UU MM PP EE

NN

12 DISMANTLING AND ASSEMBLY OF THE SHAFT SEALING

PAGE12.0





copy to:

12 Removal and Fitting of the Single Mechanical Seal (Spectra 6/300 - 3/12000)

� Carefully slide out mechanical seal housing (7005) together with the parts of the mechanical seal contained in it from connecting shaft (1050).

� Carefully push mechanical seal (7010) stationary seat out of mechanical seal housing (7005).

Refitting is a simple reversal of the above procedure.

� To reduce frictional forces during seal assembly, apply some glycerine to the shaft and the seal housing in the area of the gaskets.

� Special care must be taken when fitting double PTFE-coated gaskets:the joint of the outer coating must point away from the seal assemblydirection, otherwise the coating may open or be pulled off!

Ensure that the distribution of pressure is uniform when insertingthe pressure sensitive counter rings. When inserting larger rings, use a suitable mandrel. Do not allow any foreign bodies to get between the sliding surfaces.

� Exactly keep to the seal installation dimensions and ensure that the sealing faces are correctly pressed together (see table on sectional drawing W 209.000 or W 210.000).

� Insert mechanical seal (7010) stationary seat into mechanical seal housing (7005).

� Insert mechanical seal housing (7005) together with the stationary seatinto the drive stool without the installed connecting shaft (1050).

� If necessary take the installation dimension from the table and add the thickness S of the set ring (7086) when existing.

� Mark this installation dimension on the connecting shaft (1050).

� Fix the rotating unit of the mechanical seal (7010) on the connceting shaft (1050) depending on the installation dimension so that the rotating unit of the mechanical seal (7010) or the set ring (7086) is at the mark.

� Insert connecting shaft (1050) with the rotating unit of the mechanical seal (7010) into drive stool (0085) and install lip seal (7091, if existing. Push the set ring (1035) on to connecting shaft (1050) and observe at this the installation direction (see mark). Push connecting shaft (1050) on to the drive shaft and connect with pin (1030). Push the set ring (1035) on pin (1030).

GB

GB

12 DISMANTLING AND ASSEMBLY OF THE SHAFT SEALING

PAGE12.0R



dated approved 03.05.95 Eitler


copy to: GB

12 Removal and Fitting of the Single Mechanical Seal (Spectra 12/1 - 12/105)

Utmost cleanliness must be observed for all removal and fitting activities.Please avoid any damage to the sealing surfaces and gaskets.The sealing unit is dismantled on the shaft.

� Remove all visible connecting screws and pull apart the seal housing on the shaft. The seal housing can be made up of several parts, depending on the seal construction.Compare the attached Sectional Drawing W...!

� Carefully remove the housing parts from the shaft together with the seal counter face parts, one after the other.

� Carefully push the seal counter face parts out of the housing parts.

� Special care must be taken when fitting double PTFE-coated gaskets:the joint of the outer coating must point away from the seal assemblydirection, otherwise the coating may open or be pulled off!

Refitting is a simple reversal of the above procedure.

� To reduce frictional forces during seal assembly, apply some glycerine to the shaft and the seal housing in the area of the gaskets.

Ensure that the distribution of pressure is uniform when insertingthe pressure sensitive counter rings. When inserting larger rings, use a suitable mandrel. Do not allow any foreign bodies to get between the sliding surfaces.

� Important : Exactly keep to the seal installation dimensions and ensure that the sealing faces are correctly pressed together (see Manufacturer's catalogue).

NN EE MM OO

PP

UU MM PP EE

NN

13 RECOMMENDED STOCK OF WEAR PARTS

PAGE13.0





copy to:

13 Recommended Spare Parts

In general, we have all spare parts in stock. Our subsidiaries and exclusiverepresentatives also hold a certain stock. For special cases and when shortwaiting periods are not acceptable, we recommend to keep an amount of spare parts, corresponding to the pump, in stock on site (please see table below).

– Rotor – Stator – Elastomer parts as O-rings and sleeves – joint parts – shaft seals.

To avoid mistakes in delivery, please identify the parts by their position number shown in the spare parts list or on the sectional drawing.

GB

GB

NN EE MM OO

PP

UU MM PP EE

NN

14 SECTIONAL DRAWINGS AND LIST OF SPARE PARTS

PAGE14.0





copy to:

14 Sectional Drawings and List of Spare Parts

GB

GB

Maßs

t./sc

ale:

Datu

m/

date

Name

Unte

rsch

rift/

Sign

atur

ege

zeich

net

/dr

awn

gepr

üft

/ch

ecke

dfr

eige

gebe

n/

releas

edVe

rteiler:

Abl./

Stor

age

Revision

:

Type:

Spec

tra

12/1

-12/105

1:X

1999

5075

8235

5425

1998

5425

8235

1050

5075

1055

7086

7010

0140

0120

0125

0085

7005

2030

2025

8110

2010

3010

3005

3015

3020

2005

9500

SPARE PARTS LISTProminent® Spectra Progressing Cavity Pumps

Pos. No (Type) : Quantity Designation

0085 1 drive stool0120 4 spring washer0125 4 hex head screw0140 4 hex nut1030 (6/300 - 3/12000) : 1 pin1035 (6/300 - 3/12000) : 1 thrower1050 1 connecting shaft1055 (12/1 - 12/105) : 1 pin1998 1 coupling rod1999 1 rotor2005 1 end stud2010 1 housing2015 (6/300 - 3/12000) : 1 screw2016 (6/300 - 3/12000) : 1 screw2020 (6/300 - 3/12000) : 4 bolt2025 (12/1 - 12/105) : 2 spring washer2025 (6/300 - 3/12000) : 4 spring washer2030 (12/1 - 12/105) : 2 hex nut2030 (6/300 - 3/12000) : 4 hex nut2035 (6/300 - 3/12000) : 1 support3005 1 stator3010 (12/1 - 12/105) : 2 thru bolt3010 (6/300 - 3/12000) : 4 thru bolt3015 (12/1 - 12/105) : 2 spring washer3015 (6/300 - 3/12000) : 4 spring washer3020 (12/1 - 12/105) : 2 hex nut3020 (6/300 - 3/12000) : 6 hex nut3070 4 spring washer5065 (3/3000 - 3/12000) : 2 circlip5075 2 pin5115 (3/3000 - 3/12000) : 2 sleeve5425 2 clamp ring5990 see page 7.2 lubricating oil7005 1 seal housing7010 1 mechanical seal7086 (12/1 - 12/105) : 1 set ring8010 (6/300 - 3/12000) : 1 gasket8012 (6/300 - 3/12000) : 1 gasket8015 (6/300 - 3/12000) : 1 O-ring8110 (12/1 - 12/105) : 1 gasket8060 (3/3000 - 3/12000) : 4 O-ring8235 2 SM-pin joint seal9000 1 substructure

9500 1 drive

15 EC DECLARATION OF CONFORMITY PAGE15.0

Datum Name Unterschrift Revision:

erstellt 12.03.03 Mangel Ersatz für Ausgabe

geprüft 13.03.03 Denk vom

freigegeben 13.03.03 DenkText-Nr. 30700

Verteiler:D

15 EC declaration of conformity

GB

- Original -

We, ProMinent Dosiertechnik GmbHIm Schuhmachergewann 5 - 11D - 69123 Heidelberg

hereby declare that the product identified below conforms to the basic health and safety requirements of the EC Directive, by virtue of its design and construction, and in the configurationplaced on the market by us.This declaration is no longer applicable if changes are made to the product without our authorisation.

Product description: Eccentric screw pump, Spectra series

Product type: Spectra…

Serial no.: see type plate on the unit

Applicable EC Machinery Directive (2006/42/EC)EC Directives: EC EMC Directive (2004/108/EC)

The safety objectives of the Low Voltage Directive 2006/95/ECwere complied with in accordance with Appendix 1, No. 1.5.1 of the Machinery Directive 2006/42/EC

Applied harmonised standards, EN ISO 12100, EN 809especially:

Technical documentation was Dr. Johannes Hartfielcompiled by the authorised Im Schuhmachergewann 5-11representative for documentation: D - 69123 Heidelberg

Date / Manufacturer signature: 08.03.2012

Name / position of the signatory: Joachim Schall, Manager Innovation and Technology

EC Declaration of Conformity for Machinery

Intelligent Drivesystems, Worldwide Services

B1000 Operating and Assembly Instructions for Gear Units and Geared Motors

GB

DRIVESYSTEMS

Contents

www.nord.com B1000-GB-2511 -3-

1. Notes .............................................................................................................................. 4 1.1 General information ........................................................................................................ 4 1.2 Safety and information symbols ..................................................................................... 4 1.3 Correct use ..................................................................................................................... 4 1.4 Safety information........................................................................................................... 5 1.5 Other documents ............................................................................................................ 6 1.6 Disposal .......................................................................................................................... 6

2. Description of gear units.............................................................................................. 7 2.1 Type designations and gear unit types........................................................................... 7 2.2 Name plate ..................................................................................................................... 8

3. Assembly instructions, storage, preparation, installation ....................................... 9 3.1 Storing the gear unit ....................................................................................................... 9 3.2 Long-term storage .......................................................................................................... 9 3.3 Transporting the gear unit ............................................................................................ 10 3.4 Preparing for installation............................................................................................... 10 3.5 Installing the gear unit .................................................................................................. 11 3.6 Fitting hubs on the gear shafts ..................................................................................... 12 3.7 Fitting push-on gear units ............................................................................................. 13 3.8 Fitting shrink discs ........................................................................................................ 15 3.9 Fitting the covers .......................................................................................................... 16 3.10 Fitting a standard motor.............................................................................................. 17 3.11 Retrospective paintwork ............................................................................................. 18 3.12 Fitting the cooling coil to the cooling system .............................................................. 19

4. Commissioning ........................................................................................................... 20 4.1 Checking the oil level.................................................................................................... 20 4.2 Activating the automatic lubricant dispenser ................................................................ 20 4.3 Operation with lubricant cooling ................................................................................... 21 4.4 Running-in time for the worm gear unit ........................................................................ 21 4.5 Checklist ....................................................................................................................... 21

5. Service and maintenance........................................................................................... 22 5.1 Service and maintenance intervals............................................................................... 22 5.2 Service and maintenance work .................................................................................... 22

6. Appendix...................................................................................................................... 26 6.1 Versions and maintenance ........................................................................................... 26 6.2 Torque values ............................................................................................................... 37 6.3 Troubleshooting ............................................................................................................ 37 6.4 Lubricants ..................................................................................................................... 38 6.5 Lubricant quantities....................................................................................................... 40

1. Notes

-4- B1000-GB-2511 www.nord.com

1. Notes

1.1 General information Read the Operating Manual carefully prior to performing any work on or putting the gear unit into operation. Strict compliance with the instructions in this Operating Manual is essential. Getriebebau NORD accepts no liability for damage to persons, materials or assets as a result of the non-observance of this Operating Manual, operating errors or incorrect use. General wearing parts, e.g. radial seals are excluded from the warranty. If additional components are attached to or installed in the gear unit (e.g. motor, cooling system, pressure sensor etc.) or components (e.g. cooling system) are supplied with the order, the operating instructions for these components must be observed. If geared motors are used, compliance with the Motor Operating Manual is also necessary. If you do not understand the contents of this Operating Manual or additional operating instructions, please consult Getriebebau NORD!

1.2 Safety and information symbols Please always observe the following safety and information symbols!

Danger!

Risk of fatalities and injury

Attention!

Machine may be damaged

Note!

Useful information

1.3 Correct use These gear units generate a rotational movement and are intended for use in commercial systems. The gear unit must only be used according to the information in the technical documentation from Getriebebau NORD.

Danger!

Use in explosion hazard areas is prohibited.

Strict compliance with the technical data on the rating plate is essential. The documentation must be observed. Appropriate safety measures must be taken for applications where failure of a gear unit or geared motor may result in injury.

1. Notes


1.4 Safety information All work including transportation, storage, installation, electrical connection, commissioning, servicing, maintenance and repair must be performed only by qualified specialist personnel. It is recommended that repairs to NORD Products are carried out by the NORD Service department.

Danger!

Installation and maintenance work must only be performed when gear units are at a standstill and have cooled down. The drive must be isolated and secured to prevent accidental start-up.

Tighten the drive elements or secure the parallel key before switching on.

Danger!

Only transport use the eyebolts attached to the gear unit. No additional loads may be attached. Transportation aids and lifting gear must have an adequate load-bearing capacity.

If geared motors have an additional eyebolt attached to the motor, this must also be used. Avoid pulling the eyebolts at an angle. The thread of the eyebolt must be fully screwed in.

Observe all safety information, including that provided in the individual sections of this Operating Manual. All national and other regulations on safety and accident prevention must also be observed.

Danger!

Serious physical and property damage may result from inappropriate installation, non-designated use, incorrect operation, non-compliance with safety information, unauthorised removal of housing components or safety covers and structural modifications to the gear unit.

1. Notes


1.5 Other documents Further information may be obtained from the following documents:

- Gear unit catalogues (G1000, G2000, G1011, G1012, G1034, G1035)

- Operating and maintenance instructions for the electric motor

- if applicable, operating instructions for attached or supplied options

1.6 Disposal Observe the current local regulations. In particular, lubricants must be collected and disposed of correctly.

Gear unit components: Material: Toothed wheels, shafts, rolling bearings, parallel keys, locking rings, …

Steel

Gear unit housing, housing components, … Grey cast iron Light alloy gear unit housing, light alloy gear unit housing components, …

Aluminium

Worm gears, bushes, ... Bronze Radial seals, sealing caps, rubber components,… Elastomers with steel Coupling components Plastic with steel Flat seals Asbestos-free sealing material Gear oil Additive mineral oil Synthetic gear oil (rating plate code: CLP PG) Polyglycol-based lubricants Cooling spiral, embedding material of the cooling spiral, screw fittings

Copper, epoxy, yellow brass

2. Description of Gear Units


2. Description of gear units

2.1 Type designations and gear unit types

Helical gear units SK 11E, SK 21E, SK 31E,SK 41E, SK 51E (single-stage)

SK 02, SK 12, SK 22, SK 32, SK 42, SK 52, SK 62N (2-stage)

SK 03, SK 13, SK 23, SK 33N, SK 43, SK 53 (3-stage) SK 62, SK 72, SK 82, SK 92, SK 102 (2-stage) SK 63, SK 73, SK 83, SK 93, SK 103 (3-stage)

NORDBLOC helical gear units SK 320, SK 172, SK 272, SK 372, SK 472, SK 572, SK 672,

SK 772, SK 872, SK 972 (2-stage) SK 273, SK 373, SK 473, SK 573, SK 673, SK 773, SK 873,

SK 973 (3-stage) SK 072.1, SK 172.1, SK 372.1, SK 572.1, SK 672.1, SK 772.1

SK 872.1, SK 972.1 (2-stage) SK 373.1, SK 573.1, SK 673.1, SK 773.1, SK 873.1,

SK 973.1 (3-stage)

Standard helical gear units SK 0, SK 01, SK 20, SK 25, SK 30, SK 33 (2-stage) SK 010, SK 200, SK 250, SK 300, SK 330 (3-stage)

Parallel shaft gear units SK 0182NB, SK 0282NB, SK 1282, SK 2282, SK 3282,

SK 4282, SK 5282, SK 6282, SK 7282, SK 8282, SK 9282, SK 10282, SK 11282 (2-stage)

SK 1382NB, SK 2382, SK 3382, SK 4382, SK 5382, SK 6382, SK 7382, SK 8382, SK 9382, SK 10382,

SK 11382, SK 12382 (3-stage)

Bevel gear units SK 92072, SK 92172, SK 92372, SK 92672, SK 92772

(2-stage) SK 9012.1, SK 9016.1, SK 9022.1, SK 9032.1, SK 9042.1, SK 9052.1, SK 9062.1, SK 9072.1,

SK 9082.1, SK 9086.1, SK 9092.1, SK 9096.1 (3-stage) SK 9013.1, SK 9017.1, SK 9023.1, SK 9033.1, SK 9043.1,

SK 9053.1 (4-stage)

Contrate worm gear unit SK 02040, SK 02050, SK 12063, SK 12080,

SK 32100,SK 42125 (2-stage) SK 13050, SK 13063, SK 13080, SK 33100, SK 43125

(3-stage)

MINIBLOC worm gear units SK1 S32, SK1 S40, SK 1S50, SK 1S63, SK 1SU...

SK 1SM31, SK 1SM40, SK 1SM50, SK 1SM63 (single-stage)SK 2S32NB, SK 2S40NB, SK 2S50NB, SK 2S63NB,

SK 2SU…, SK 2SM40, SK 2SM50, SK 2SM63 (2-stage)

UNIVERSAL worm gear units SK 1SI31, SK 1SI40, SK 1SI50, SK 1SI63, SK 1SI75,

SK 1SIS31,…, SK 1SIS75, SK 1SD31, SK 1SD40,SK 1SD50, SK 1SD63, SK 1SIS-D31,…, SK 1SIS-D63 (single-stage)

SK 2SD40, SK 2SD50, SK 2SD63, SK 1SI…/31, SK 1SI…/H10,

SK 2SIS-D40,…, SK 2SIS-D63 (2-stage)

Versions / Options

- Foot mounting with solid shaft A Hollow shaft version V Solid shaft version L Solid shaft both sides Z Drive flange B14 F Output flange B5 X Foot mounting XZ Base and output flange B14 XF Base and output flange B5 AL Reinforced axial drive bearings 5 Reinforced output shaft

(Standard helical gear unit) V Reinforced drive shaft

(Standard helical gear unit) D Torque support K Torque console S Shrink disc VS Reinforced shrink disc EA Hollow shaft with internal spline G Rubber buffer VG Reinforced rubber buffer R Back stop B Fixing element H Covering cap as contact guard H66 Covering cap IP66 VL Reinforced bearings VL2 Agitator design VL3 Drywell agitator design IEC Standard motor mounting NEMA Standard motor mounting W With free drive shaft VI Viton radial seals OA Oil expansion vessel OT Oil level tank SO1 Synthetic oil ISO VG 220 CC Casing cover with cooling spiral DR Spring Loaded Breather H10 Modular contrate pre-stage /31 Worm pre-stage /40 Worm pre-stage

Double gear units consist of two single gear units. They are to be treated as per the instructions in this Manual, i.e. as two individual gear units. Type designation of double gear units: e.g. SK 73/22 (consisting of single gears SK 73 and SK 22)

2. Description of Gear Units


2.2 Name plate

Explanation of the Name Plate 1 Matrix – Barcode

2 NORD gear unit type

3 Operating mode

4 Year of manufacture

5 Serial number

6 Rated torque of gear unit output shaft

7 Drive power

8 Weight according to ordered version

9 Overall gear unit ratio

10 Installation orientation

11 Rated speed of gear unit output shaft

12 Lubricant type, viscosity and quantity

13 Customer’s part number

14 Operating factor

3. Assembly instructions, storage, preparation, installation


3. Assembly instructions, storage, preparation, installation Please observe all of the general safety information in Section 1.4, 1.3 and in the individual sections.

3.1 Storing the gear unit For short-term storage before commissioning, please observe the following:

• Store in the fitting position (see Section 6.1) and secure gear units against falling • Lightly grease bare metal housing surfaces and shafts • Store in dry rooms • Temperature must not fluctuate beyond the range of –5 oC to +40 oC • Relative humidity less than 60% • No direct exposure to sunlight or UV light • No aggressive, corrosive substances (contaminated air, ozone, gases, solvents, acids,

alkalis, salts, radioactivity etc.) in the immediate vicinity • No vibration or oscillation

3.2 Long-term storage

Note!

For storage or standstill periods in excess of 9 months, Getriebebau NORD recommends the long-term storage option. With the long-term storage option and the use of the measures listed below, storage for up to 2 years is possible. As the actual influences on the unit greatly depend on the local conditions, these times should only be regarded as guide values.

Conditions of the gear unit and storage area for long-term storage prior to commissioning: • Store in the fitting position (see Section 6.1) and secure gear units against falling • Transportation damage to the external paint must be repaired. Check that a suitable rust

inhibitor is applied to the flange bearing surfaces. If necessary apply a suitable rust inhibitor to the surfaces.

• Gear units with the long-term storage option are completely filled with lubricant or have VCI corrosion protection agents added to the gear oil. (See label on gear unit)

• The sealing band in the vent plug must not be removed during storage. The gear unit must remain sealed tight.

• Store in a dry place. • In tropical regions, the drive unit must be protected against damage by insects • Temperature must not fluctuate beyond the range of –5 oC to +40 oC • Relative humidity less than 60% • No direct exposure to sunlight or UV light • No aggressive, corrosive substances (contaminated air, ozone, gases, solvents, acids,

alkalis, salts, radioactivity etc.) in the immediate vicinity • No vibration or oscillation

Measures during storage or standstill periods • If the relative humidity is

3. Assembly instructions, storage, preparation, installation


3.3 Transporting the gear unit

Danger!

To prevent injury, the danger area must be generously cordoned off. Standing under the gear unit during transport is extremely dangerous.

Attention!

Avoid damage to the gear unit. Impacts to the free ends of the shafts may cause internal damage to the gear unit.

Use adequately dimensioned and suitable means of transportation. Lifting tackle must be designed for the weight of the gear unit. The weight of the gear unit can be obtained from the dispatch documents.

3.4 Preparing for installation The drive unit must be inspected and may only be installed if no transportation damage or leaks are visible. In particular the radial seals and the sealing caps must be inspected for damage. All bare metal surfaces and shafts of the gear unit are protected against corrosion with oil, grease or corrosion protection agents before shipping. Thoroughly remove all oil, grease or corrosion protection agents and any dirt from the shafts and flange surfaces before assembly. In applications where an incorrect rotational direction may result in damage or potential risk, the correct rotational direction of the drive shaft is to be established by test running the drive when uncoupled and guaranteeing such for subsequent operation. Gears with integrated return stops are marked w

Operating and Maintenance Instructions ...€¦ · 1 SAFETYPRECAUTIONS PAGE 1.0R Revision:6 Date...

Documents

Transcript of Operating and Maintenance Instructions ...€¦ · 1 SAFETYPRECAUTIONS PAGE 1.0R Revision:6 Date...