KIT200 Installation Manual - KEF · Issue 1: August 2005 (GB) Installation Manual(F) Manuel...

104
Part No.290185ML Issue 1: August 2005 (GB) Installation Manual (F) Manuel d’installation (D) Bedienungsanleitung (I) Manuale d’installazione (ES) Manual de instalación (P) Manual de instalação (NL) Gebruiksaanwijzing KIT200 Installation Manual Home Entertainment System www.kef.com

Transcript of KIT200 Installation Manual - KEF · Issue 1: August 2005 (GB) Installation Manual(F) Manuel...

  • Part No.290185MLIssue 1: August 2005

    (GB) Installation Manual (F) Manuel d’installation (D) Bedienungsanleitung (I) Manuale d’installazione

    (ES) Manual de instalación (P) Manual de instalação (NL) Gebruiksaanwijzing

    KIT200 Installation ManualHome Entertainment System

    www.kef.com

    KIT200_Manual.qxd 10/1/11 15:04 Page 1

  • 2

    english instructions

    Turn power off before connecting and disconnecting all cablesEnsure that the KEF instant theatre is powered off before connecting or disconnecting the subwoofer to head unitcable. Removing or adding this lead when power is switched on may damage the system.

    CAUTION:To prevent electric shock, match wide blade of plug to wide slot, insert fully.

    Warning:This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objectscontaining liquids, such as vases, upon the apparatus.

    Class 1 laser productThe DVD player contained within this system is classified as a CLASS 1 LASER PRODUCT according to EN60825-1:1994 + A11. The CLASS 1 LASER PRODUCT label is located on the bottom of the DVD unit.

    CAUTION:Use of controls or adjustments or performance of procedures other than those specified hereinmay result in hazardous radiation exposure.The DVD player should not be adjusted or repaired by anyone except properly qualified servicepersonnel.

    Class B emissions limitsThis Class B digital apparatus meets all requirements of the Canadian Interference-CausingEquipment Regulations.

    BatteriesPlease dispose of used batteries properly, following any local regulations. Do not incinerate.

    important safety instructionsPlease read this owner’s guide

    •Read these instructions and heed all warnings.•Do not use this apparatus near water.•The apparatus shall be connected to a mains socket outlet with a protective earthing connection•Clean only with a damp cloth.•The apparatus should be installed in a well-ventilated area. That allows access to power off the unit, or pull thepower cord plug away frompower outlet without obstruction.

    •Please take the time to follow this owner’s guide carefully. It will help you set up and operate your systemproperly, and enjoy all of its advanced features. Save this owner’s guide for future reference.

    •Do not block the ventilation openings at the rear of the subwoofer.•Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (includingamplifiers) that produce heat.

    •Do not defeat the safety purpose of the polarized or grounding - type plug. The wide blade or the third prong areprovided for your safety. If the provided plug does not fit into your outlet, consult an electrician forreplacement of the obsolete outlet.

    •Protect the power cord and plugs from being walked on or pinched.•Only use attachments/accessories specified by KEF.•Unplug this apparatus during lightning storms or when unused for long periods of time.•Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged inany way, such aspower-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, theapparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

    •When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

    WARNINGTO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK,DO

    NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

    CAUTIONRISK OF ELECTRICSHOCK

    DO NOT OPEN

    Explanation of Graphical SymbolsThe lightning flash with arrowhead symbol, within an equilateraltriangle, is intended to alert the user to the presence of uninsulated“dangerous voltage” within the product’s enclosure that may be ofa sufficient magnitude to constitute a risk of electrical shock topersons.

    The exclamation mark within an equilateral triangle is intended toalert the user to the presence of important operating and

    maintenance (servicing) instructions in the literature accompanying theappliance.

    CAUTION:TO REDUCE THERISK OF ELECTRIC SHOCK, DO NOT

    REMOVE COVER (OR BACK).

    NO USER-SERVICEABLE PARTSINSIDE. REFER SERVICING TO

    QUALIFIED SERVICE PERSONNEL.

    CLASS 1 LASER PRODUCT

    KLASSE 1 LASER PRODUKT

    LUOKAN 1 LASER LAITE

    KLASS 1 LASER APPARAT

    KIT200_Manual.qxd 10/1/11 15:04 Page 2

  • 3

    Veillez à mettre l’appareil hors tension avant de brancher ou débrancher tous les connecteurs et câbles.Assurez-vous que le KEF KIT est éteint avant de connecter ou déconnecter le subwoofer de l’unité principale.Connecter ou déconnecter ce câble lorsque l’appareil est sous tension pourrait détériorer celui-ci.

    DANGER :Pour éviter tout choc électrique, placez la lame large de la prise dans la fente large et enfoncez entièrement.

    Avertissement :Cet appareil électrique ne doit pas être exposé à l’humidité ni aux éclaboussures et il convient deveiller à ne pas plaçer d’objets contenant des liquides, tels que des vases, sur l’appareil.

    Produit laser de classe 1Le lecteur DVD contenu dans ce système est classé comme PRODUIT LASER DE CLASSE 1 selon la norme EN60825-1:1994 + A11. L’étiquette PRODUIT LASER DE CLASSE 1 est située au bas de l’unité DVD.

    DANGER :Toute utilisation des commandes, des réglages ou des procédures de performances autre que celles spécifiées dans leprésent document peut entraîner une exposition dangereuse aux rayonnements.Le lecteur DVD ne doit en aucune manière être réglé ou réparé par du personnel non qualifié.

    Limites d’émission de classe BCet appareil numérique de classe B est conforme à toutes les exigences du Règlement canadien sur le matérielbrouilleur.

    PilesVeuillez vous débarrasser des piles usagées de manière adéquate en respectant les normes localeséventuelles en la matière. Ne pas brûler.

    Importantes consignes de sécuritéVeuillez lire attentivement ce guide du propriétaire• Lisez ces instructions et tenez compte de tous les avertissements.• Ne placez pas cet appareil à proximité d’eau.• Branchez l’appareil sur une prise de courant électrique reliée à la terre.• Nettoyez l’appareil à l’aide d’un chiffon humide uniquement.• Installez l’appareil dans une zone bien aérée et suffisamment dégagée pour permettre dele débrancher facilement.• Prenez le temps de parcourir attentivement ce guide. Il vous aidera à configurer et à utiliser votre systèmecorrectement et à profiter de toutes ses fonctions. Conservez ce guide pour référence.• Ne bloquez pas les ouvertures de ventilation à l’arrière du subwoofer.• Ne placez pas le subwoofer à proximité de sources de chaleur telles que des radiateurs, des bouches dechauffage, des poêles ou d'autres appareils qui génèrent de la chaleur (amplificateurs y compris).• N’entravez pas les éléments de sécurité de la fiche polarisée ou de mise à la terre. La broche plus large ou latroisième broche sont fournies pour votre sécurité. Si la fiche fournie ne rentre pas dans votre prise, faites appelà un électricien qui procèdera au remplacement de celle-ci.• Protégez le cordon et la fiche d’alimentation de façon à ce qu’ils ne puissent pas être piétinés ni pincés.• Utilisez uniquement les compléments/accessoires spécifiés par KEF.• Débranchez l’appareil pendant les orages ou les longues périodes d’inutilisation.• Confiez toute réparation aux techniciens compétents. Un envoi en réparation est nécessaire lorsque l’appareila été endommagé de quelconque façon : cordon ou fiche d’alimentation endommagés, contact avec un liquide, chuted’objets, exposition à la pluie ou l’humidité, dysfonctionnement ou chute.• Si l’appareil est posé sur un chariot, déplacez celui-ci avec prudence pour éviter qu’il ne se renverse et vousblesse.• L’appareil ne peut recevoir ni gouttes ni éclaboussures. Ne placez aucun objet contenant un liquide, comme unvase, sur l'appareil.• L’interrupteur de secteur est la seule manière de débrancher l’appareil. Il doit être accessible à tout moment.Pour isoler complètement l’alimentation, placez l’interrupteur en position ARRÊT.• Lorsque l’appareil est complètement débranché, la diode de veille est éteinte. La fiche secteur doit être libre

    AVERTISSEMENTPOUR REDUIRE LE RISQUE D’INCENDIE OU DE CHOC

    ELECTRIQUE,N’EXPOSEZ PAS CET APPAREIL A LA PLUIEOU A L’HUMIDITE

    Explication des symboles graphiquesLe symbole de l’éclair avec la flèche dans un triangle équilatéral apour but de prévenir l’utilisateur de la présence d’une “tensiondangereuse” non isolée dans le boîtier du produit qui peut être d’uneampleur suffisante pour constituer un risque de choc électrique pourles personnes.

    Le point d’exclamation dans un triangle équilatéral a pour but deprévenir l’utilisateur de la présence d’instructions importantespour le fonctionnement et la maintenance dans le manuel livré avec

    l’appareil.

    AVISRISQUE DECHOC

    ÉLECTRIQUENE PASOUVRIR

    DANGER:POUR REDUIRE LERISQUE DE CHOC ELECTRIQUE, NE PASENLEVER LE COUVERCLE (OU LA PAR-

    TIE ARRIERE).

    AUCUNE PIECE A ENTRETENIR PARL’UTILISATEUR A L’INTERIEUR CONFIEZ

    CLASSE 1 PRODUIT LASER

    KLASSE 1 LASER PRODUKT

    LUOKAN 1 LASER LAITE

    KLASS 1 LASER APPARAT

    instructions en français

    KIT200_Manual.qxd 10/1/11 15:04 Page 3

  • 4

    Schalten Sie das Gerät ab, bevor Sie Kabelverbindungen herstellen oder lösen.Stellen Sie sicher, dass das KEF Instant Theatre abgeschaltet ist, bevor Sie die Kabelverbindung vom Subwoofer zumDVD-Receiver herstellen oder lösen. Wenn Sie diese Kabelverbindung herstellen oder lösen, während das Geräteingeschaltet ist, kann die Anlage beschädigt werden.

    Achtung:Um einen elektrischen Schlag zu vermeiden, stecken Sie den Stecker komplett in die Steckdose.

    Warnung:Achten Sie sorgfältig darauf, dass diese Geräte keinem Tropf- oder Spritzwasser ausgesetzt werden. Schützen SieIhr Gerät vor Feuchtigkeit! Stellen Sie keine mit Flüssigkeit gefüllten Gefäße wie Vasen oder Gläser auf das Gerät,damit keine tropfende oder überlaufende Flüssigkeit in das Gerät gelangen kann.

    “CLASS 1 LASER PRODUCT”Der DVD-Player im DVD-Receiver ist ein KLASSE 1 LASER PRODUKT und enthält einen Laser imGehäuse nach EN60825-1:1994 + A11. Der “CLASS 1 LASER PRODUCT”-Aufkleber ist unter demBoden des DVD-Receivers angebracht.

    Achtung:Eine andere Verwendung der Regler, Einstellungen oder Einstellverfahren als in dieser Anleitung beschrieben, kann zugefährlicher Strahlung führen. Der DVD-Receiver darf nur durch qualifiziertes Service-Personal eingestellt oderrepariert werden.

    Klasse B EmissionsbegrenzungenDieses Klasse B Gerät entspricht allen Anforderungen der Kanadischen “Interference-CausingEquipment Regulations”.

    BatterienGeben Sie verbrauchte Batterien bei den entsprechenden Sammelstellen ab.

    wichtige sicherheitshinweiseBitte lesen Sie diese Gebrauchsanweisung.

    •Lesen Sie alle Anleitungen, und beachten Sie alle Warnungen.•Verwenden Sie dieses Gerät nicht in der Nähe von Wasser.•Das Gerät muss an eine geerdete Steckdose angeschlossen werden.•Reinigen Sie das Gerät nur mit einem feuchten Tuch.•Um das Gerät sollte ausreichend Platz gelassen werden, damit die nötige Belüftung gewährleistet ist. Das Gerätist so außerdem leichter zugänglich, und Sie können es problemlos ausschalten oder das Stromkabel aus derSteckdose ziehen.

    •Nehmen Sie sich ausreichend Zeit, um diese Informationen ausführlich zu lesen. Sie helfen Ihnen dabei, dasSystem ordnungsgemäß einzurichten und zu betreiben und alle Funktionen optimal zu nutzen. Bewahren Sie dieseAnleitung auf, um sie zukünftig als Referenz verwenden zu können.

    •Verstellen Sie nicht die Lüftungsöffnungen auf der Rückseite des Subwoofers.•Stellen Sie das Gerät nicht in der Nähe von Heizquellen, z. B. Heizkörpern, Heizregistern, Öfen oder anderenwärmeerzeugenden Geräten (einschließlich Verstärkern) auf.

    •Sie dürfen die Sicherheitsfunktion polarisierter oder geerdeter Stecker nicht außer Kraft setzen. Der breite Polbzw. der dritte Stift dient Ihrer Sicherheit. Wenn der mitgelieferte Stecker nicht in die Steckdose passt, lassenSie die veraltete Steckdose von einem Elektriker austauschen.

    •Achten Sie darauf, dass das Stromkabel und die Stecker nicht übermäßig belastet oder abgeknickt werden.•Verwenden Sie nur Zubehör, das von KEF empfohlen wird.•Trennen Sie dieses Gerät bei Gewitter oder längerer Nichtbenutzung vom Netz.•Lassen Sie alle Wartungen von geschultem Kundendienstpersonal durchführen. Eine Wartung ist erforderlich,wenn das Gerät auf irgendeine Weise beschädigt wurde, z. B. durch Schäden am Netzkabel oder -stecker, durchVerschütten von Flüssigkeiten, durch Regen oder Feuchtigkeit, wenn Objekte in das Gerät gefallen sind oder wennes nicht richtig funktioniert oder fallen gelassen wurde.

    •Bei Verwendung eines Wagens sollten Sie vorsichtig sein, damit Gerät und Wagen nicht umkippen und

    WARNUNGUm Brandgefahr und einen elektrischen Schlag zu vermeiden,

    schützen Sie Ihre Geräte vor Regen und Feuchtigkeit.

    Erklärung der graphischen Symbole

    Das Blitzsymbol innerhalb eines gleichseitigen Dreiecks warnt vorunisolierter, gefährlicher, elektrischer Spannung innerhalb desGehäuses, die stark genug ist,um einen gefährlichen elektrischen Schlag zu verursachen.

    Das Ausrufezeichen innerhalb eines gleichseitigen Dreiecks weistden Anwender auf wichtige Anwendungs- und Wartungsanweisungen(Service) in der Literatur hin,die dem Produkt beigelegt ist.

    CLASS 1 LASER PRODUCT

    KLASSE 1 LASER PRODUKT

    LUOKAN 1 LASER LAITE

    KLASS 1 LASER APPARAT

    deutsche bedienungsanleitung

    ACHTUNG:NICHT ÖFFNEN!

    GEFAHR DURCH

    STROMSCHLAG!

    ACHTUNG: UM DIE GEFAHREINES ELEKTRISCHEN STROMSCHLAGESZU VERHINDERN, ENTFERNEN SIE NICHT

    DIE GEHÄUSEABDECKUNG (ODERRÜCKWAND). ES BEFINDEN SICH KEINEBEDIENELEMENTE INNERHALB DES

    GERÄTS. LASSEN SIE REPARATUREN NURDURCH GESCHULTES PERSONAL

    DURCHFÜHREN.

    KIT200_Manual.qxd 10/1/11 15:04 Page 4

  • 5

    Disinserire l'alimentazione prima di collegare e scollegare tutti i caviAccertarsi che l'Instant Theatre KEF sia spento prima di collegare o scollegare il cavo tra subwoofer e unitàprincipale. Lo scollegamento o il collegamento di questo cavo con l’alimentazione inserita potrebbe danneggiare ilsistema.

    ATTENZIONE:Avvertenza:Questo dispositivo elettrico non deve essere esposto a schizzi o spruzzi, prestare quindi attenzione a non collocaresulla sua superficie oggetti contenenti liquidi, ad esempio dei vasi.

    Prodotto laser di classe 1Il lettore DVD contenuto in questo sistema è classificato come PRODOTTO LASER DI CLASSE 1secondoEN60825-1:1994 + A11. L’etichetta PRODOTTO LASER DI CLASSE 1 è posizionata sulla parteinferiore dell’unità DVD.

    ATTENZIONE:L’utilizzo di comandi e regolazioni oppure l’esecuzione di procedure diversi da quelli indicati nel presente documentopuò provocare l’esposizione a radiazioni pericolose. Il lettore DVD deve essere regolato o riparatoesclusivamente da personale di assistenza debitamente qualificato.

    Limiti delle emissioni per la classe BQuesto dispositivo digitale di classe B è conforme a tutti i requisiti previsti dalla normativacanadese in materia di apparecchiature checausano interferenze.

    BatterieSmaltire le batterie usate in modo corretto, rispettando le norme locali. Non incenerire.

    importanti istruzioni di sicurezzaLeggere la presente guida dell’utente

    •Leggere le istruzioni e rispettare le avvertenze.•Non utilizzare l’apparecchio vicino all’acqua.•Collegare l’apparecchio a una presa elettrica con collegamento a terra.•Pulire con un panno umido.•Installare l’apparecchio in una zona ben ventilata. Prevedere uno spazio sufficiente allo spegnimentodell’apparecchio e acconsentire lo scollegamento del cavo di alimentazione senza ostacoli.

    •Leggere a fondo e attenersi alla presente guida dell’utente per poter far funzionare il sistema in condizioni disicurezza e sfruttarne tutte le funzioni. Conservare la guida per poterla consultare all’occorrenza.

    •Non ostruire le aperture di ventilazione sul retro del subwoofer.•Non installare accanto a fonti di calore come radiatori, bocchette di riscaldamento, stufe o altre apparecchiatureche producono calore (amplificatori compresi).

    •Non disattivare i contatti di terra del connettore. La lamella del contatto di terra ha funzioni di sicurezza. Se nonsi riesce a inserire la spina nella presa rivolgersi a un elettricista per far sostituire la presa.

    •Evitare che il cavo d’alimentazione venga calpestato o schiacciato.•Utilizzare esclusivamente accessori originali KEF.•Scollegare l’apparecchio durante i temporali o se non lo si usa per un lungo periodo di tempo.•Fare eseguire gli interventi di manutenzione a personale qualificato in caso di danni, ad esempio al cavo o alconnettore d’alimentazione, ingresso di liquidi o di oggetti nell’apparecchio, esposizione a pioggia o umidità,funzionamento anomalo o caduta dell’apparecchio.

    •Se si utilizza un carrello muovere l’insieme carrello/apparecchio con cautela per evitare il rischio di

    AVVERTENZAPER RIDURRE IL RISCHIO DI INCENDIO E DI SCOSSEELETTRICHE, NON ESPORRE L’APPARECCHIO ALLA

    PIOGGIA O ALL’UMIDITÀ

    Spiegazione dei simboli grafici

    Il simbolo del lampo con punta di freccia, racchiuso in un triangoloequilatero, ha la funzione di avvertire l’utente della presenza di una“tensione pericolosa” non isolata all’interno dell’involucro delprodotto di tale rilievo da poter costituire un rischio di scosse

    elettriche per le persone.

    Il punto esclamativo racchiuso in un triangolo equilatero ha lafunzione di avvertire l’utente della presenza di importanti istruzioniper il funzionamento e la manutenzione (assistenza) nella

    letteratura che accompagna l’apparecchio.

    ATTENZIONE

    RISCHIO DISCOSSE

    ELETTRICHENON APRIRE

    CLASSE 1 PRODOTTO LASER

    KLASSE 1 LASER PRODUKT

    LUOKAN 1 LASER LAITE

    KLASS 1 LASER APPARAT

    istruzioni in italiano

    ATTENZIONE:PER RIDURRE IL RIS-CHIO DI SCOSSE ELETTRICHE, NON RIMUO-VERE IL COPERCHIO (O IL PANNELLO POS-

    TERIORE)

    ALL’INTERNO NON SONO PRESENTICOMPONENTI SUI QUALI L’UTENTE POSSA

    INTERVENIRE. FAR ESEGUIRE GLI INTERVENTI DIRIPARAZIONE DA PERSONALE DI ASSISTENZA

    KIT200_Manual.qxd 10/1/11 15:04 Page 5

  • 6

    PRECAUCIÓN:A fin de evitar descargas eléctricas, introduzca completamente el enchufe en la base.

    APAGUE EL APARATO ANTES DE CONECTAR Y DESCONECTAR LOS CABLES:Asegúrese de que el KEF instant theatre está deshabilitado antes de conectar o desconectar el subwoofer de la unidadcentral. Si se desconecta o conecta el cable cuando el equipo está encendido, el sistema puederesultar dañado.

    Advertencia:No se deberá exponer este aparato eléctrico a goteos ni salpicaduras, y se deberá tener cuidado deno colocar sobre el aparato ningún objeto ni vasija que contenga líquidos.

    Producto láser de Clase 1El reproductor de DVD de este equipo está clasificado como CLASS 1 LASER PRODUCT (Producto láser de Clase 1),con arreglo a la normativa EN60825-1:1994 + A11. La etiqueta CLASS 1 LASER PRODUCT se encuentra en la parteinferior de la unidad de DVD.

    PRECAUCIÓN:El uso de controles o ajustes o la realización de procedimientos distintos a los aquí especificados puede producir unaexposición peligrosa a la radiación. No se deberá ajustar o reparar el reproductor de DVD si no es por parte depersonal de servicio con la cualificación adecuada.

    Límites de emisiones de la Clase BEste aparato digital de la Clase B cumple todos los requisitos de las normas canadienses paraequipos generadores de interferencias.

    PilasDeseche las pilas usadas de forma adecuada, cumpliendo con la normativa de su país. No lasarroje al fuego.

    instrucciones importantes de seguridadLea este manual de usuario

    •Lea estas instrucciones y respete todas las advertencias.•No utilice este aparato cerca del agua.•El aparato estará conectado a una toma de corriente con conexión a tierra.•Límpielo sólo con un trapo húmedo.•El aparato debe instalarse en una zona bien ventilada a la que se pueda acceder fácilmente para apagar la unidad odesenchufar el cable de alimentación de la toma de corriente sin que ningún obstáculo lo impida.

    •Dedique el tiempo necesario para seguir detenidamente las instrucciones de este manual del usuario. Esto le facilitarála configuración y la utilización correcta del sistema, además, así podrá disfrutar de sus funciones avanzadas. Guardeeste manual del usuario para posteriores consultas.

    •No bloquee las salidas de ventilación que hay en la parte posterior del subwoofer.•No instale el aparato cerca de focos de calor como radiadores, registros de calor, estufas u otros aparatos(incluidos amplificadores) que produzcan calor.

    •No anule el propósito de seguridad de los enchufes de tipo polarizado o a tierra. La patilla ancha o la tercera puntatienen fines de seguridad. Si el enchufe suministrado no encaja en la toma de corriente, póngase en contacto con unelectricista para que sustituya la toma desfasada.

    •Proteja el cable de alimentación y los enchufes para que no haya posibilidad de pisarlos o de que quedenatrapados.

    •Utilice únicamente accesorios especificados por KEF.•Desenchufe este aparato cuando haya tormentas eléctricas o cuando no lo vaya a utilizar durante prolongadosperiodos de tiempo.

    •Asegúrese de que todas las tareas de reparación o mantenimiento sean realizadas por personal cualificado. Lastareas de reparación son necesarias cuando el aparato se ha dañado de alguna forma, por ejemplo, el cable dealimentación o el enchufe está dañado, se ha derramado algún líquido sobre él o ha caído algún objeto en su

    ADVERTENCIAA FIN DE REDUCIR EL RIESGO DE INCENDIO O

    DESCARGAS ELÉCTRICAS, NO EXPONGA ESTE APARATOA LA LLUVIA O LA HUMEDAD.

    Descripción de los símbolos gráficos

    La finalidad del símbolo que muestra un rayo con punta de flecha,dentro de un triángulo equilátero, es alertar al usuario de lapresencia de “tensión peligrosa”sin aislar en el interior de la carcasa del producto y puede tener unamagnitud suficiente para constituir un riesgo de descarga eléctricapara las personas.

    La finalidad del símbolo que muestra un signo de admiración dentrode un triángulo equilátero es alertar al usuario de la presencia deinstrucciones importantes sobre funcionamiento y mantenimiento

    (servicio) en la documentación que acompañaal aparato.

    PRECAUCIÓN

    RIESGO DEDESCARGA

    ELÉCTRICA. NOABRIR.

    PRECAUCIÓN:A FIN DEREDUCIR EL RIESGO DE DESCARGA ELÉCTRICA,NO RETIRE LA TAPA (NI LA PARTE POSTERIOR).

    NO HAY PIEZAS REPARABLES POR EL USUARIOEN EL INTERIOR. CUALQUIER REPARACIÓN

    DEBERÁ REALIZARLA PERSONAL CUALIFICADO.

    CLASS 1 LASER PRODUCT

    KLASSE 1 LASER PRODUKT

    LUOKAN 1 LASER LAITE

    KLASS 1 LASER APPARAT

    instrucciones en español

    KIT200_Manual.qxd 10/1/11 15:04 Page 6

  • 7

    Desligue a corrente antes de ligar e desligar todos os cabosCertifique-se que o ‘KEF Instant Theatre’ está desligado antes de ligar ou desligar o subwoofer ao cabo da unidadeprincipal. Retirar ou colocar este cabo com a alimentação ligada pode danificar o sistema.

    CUIDADO:Para evitar choques eléctricos, faça corresponder a lâmina larga da ficha com a ranhura larga, einsira completamente.

    Aviso:Este aparelho eléctrico não deve ser exposto a qualquer líquido e não devem ser colocadosquaisquer objectos que contenham líquidos como, por exemplo, vasos, sobre o aparelho.

    Produto a laser da Classe 1O leitor de DVD incluído neste sistema está classificado como um PRODUTO A LASER DA CLASSE 1, de acordo comEN60825-1:1994 + A11. A etiqueta de PRODUTO A LASER DA CLASSE 1 está localizada na parte inferior da unidadedo DVD.

    CUIDADO:A utilização de comandos ou de afinações, ou a execução de procedimentos diferentes dos aqui especificados poderesultar em exposição perigosa a radiação. O leitor de DVD só deverá ser afinado ou reparado por pessoal técnicoqualificado.

    Limites das emissões da Classe BEste aparelho digital da Classe B satisfaz todos os requisitos das Normas Canadianas paraEquipamentos Causadores de Interferências.

    BateriasDesfaça-se das baterias usadas correctamente, respeitando as normas locais. Não faça aincineração.

    instruções importantes sobre segurançaLeia este manual do proprietário

    •Leia estas instruções e preste especial atenção a todos os avisos.•Não utilize este aparelho junto de água.•O aparelho deve ser ligado a uma tomada eléctrica com protecção de terra•Limpe apenas com um pano húmido.•O aparelho deve ser instalado numa zona bem ventilada. A instalação deverá ser efectuada de modo a poderdesligar a unidade, ou a retirar o cabo de alimentação da tomada eléctrica sem dificuldade.

    •Siga cuidadosamente todas as instruções deste manual do proprietário. Este manual ajudá-lo-á a configurar e afuncionar correctamente com o sistema, e a usufruir de todas as funcionalidades avançadas. Guarde este manualdo proprietário para referência futura.

    •Não bloqueie as aberturas de ventilação existentes na parte posterior do subwoofer.•Não instale junto de qualquer fonte de calor como, por exemplo, radiadores, dispositivos reguladores de calor,fogões, ou outros aparelhos (incluindo amplificadores) que produzam calor.

    •Não anule o dispositivo de segurança de polarização ou terra - tipo ficha. A lâmina larga ou o terceiro pino sãofornecidos para sua segurança. Se a ficha fornecida não couber na tomada eléctrica, consulte um electricistapara proceder à substituição da tomada obsoleta.

    •Proteja o cabo de alimentação e as fichas de modo a não serem pisados.•Utilize apenas ligações/acessórios especificados pela KEF.•Desligue este aparelho durante trovoadas ou se não o pretender utilizar durante períodos de tempo prolongados.•Qualquer tipo de assistência técnica deve ser efectuado por pessoal qualificado. A assistência técnica é requeridaquando o aparelho sofre algum tipo de dano como, por exemplo, um cabo de alimentação ou ficha danificado,queda de qualquer líquido ou objecto para o aparelho, exposição do aparelho à chuva ou humidade, maufuncionamento ou queda.

    •Quando o aparelho está colocado num móvel com rodas, deve ter o máximo cuidado quando deslocar o conjuntomóvel/aparelho para evitar que tombe.

    •O aparelho não deve ser exposto a pingos ou borrifos, e não devem ser colocados sobre o aparelho objectos coml

    AVISO PARA REDUZIR O RISCO DE INCÊNDIO OU

    CHOQUE ELÉCTRICO, NÃO EXPONHA ESTEAPARELHO À CHUVA OU À HUMIDADE

    Explicação dos símbolos gráficos

    O símbolo de um raio intermitente com uma seta, dentro de umtriângulo equilátero, destina-se a alertar o utilizador para apresença de “tensão perigosa” não isolada no interior da caixa doproduto, que pode ser suficientemente forte para constituir o riscode choque eléctrico.

    O ponto de exclamação, dentro de um triângulo equilátero, destina-se a alertar o utilizador para a presença de instruções importantessobre funcionamento e manutenção (assistência técnica) na

    literatura fornecida com o aparelho.

    CUIDADORISCO DECHOQUE

    ELÉCTRICO -NÃO ABRA

    CLASSE 1 PRODUTO A LASER

    KLASSE 1 LASER PRODUKT

    LUOKAN 1 LASER LAITE

    KLASS 1 LASER APPARAT

    instruções em português

    CUIDADO:PARA REDUZIR O RISCODE CHOQUE ELÉCTRICO, NÃO RETIRE ATAMPA (OU O PAINEL POSTERIOR).

    NO INTERIOR, NÃO EXISTEM PEÇASREPARÁVEIS PELO UTILIZADOR. AASSISTÊNCIA TÉCNICA DEVE SER

    EFECTUADA APENAS POR PESSOAL TÉCNICO

    KIT200_Manual.qxd 10/1/11 15:04 Page 7

  • 8

    Schakel de stroom uit vooraleer u alle kabels aan- en afkoppeltZorg ervoor dat het KEF Instant Theatre uitgeschakeld is vooraleer u de kabel tussen de subwoofer en de hoofdunit aan-of afkoppelt. Indien u deze kabel aan- of afkoppelt terwijl het toestel aangeschakeld is, kan hetsysteem beschadigd raken.

    OPGELET:Om elektrische schokken te vermijden dient u het brede plugblad volledig in het brede slot testeken.

    Waarschuwing:Dit elektrisch apparaat mag niet blootgesteld worden aan opspattend water of er mag niets opgeplaatst worden datvloeistof bevat (zoals een vaas).

    Klasse 1 laserproductDe DVD-speler in dit systeem wordt geklasseerd als een KLASSE 1 LASERPRODUCT overeenkomstigEN60825-1:1994 + A11. Het KLASSE 1 LASERPRODUCT label bevindt zich aan de onderkant van de DVD-unit.

    OPGELET:Indien het toestel anders gebruikt wordt dan hierin vermeld of indien bepaalde andere procedures gevolgd worden, kandit leiden tot blootstelling aan schadelijke straling.De DVD-speler mag enkel aangepast of hersteld worden door erkend gekwalificeerd onderhoudspersoneel.

    Beperkingen m.b.t. klasse B emissiesDit Klasse B digitale toestel voldoet aan alle vereisten van de Canadese Reglementering inzakeToestellen die Storingen Veroorzaken.

    BatterijenGelieve u op een correcte wijze te ontdoen van gebruikte batterijen, conform de lokale instructies.Niet verbranden.

    belangrijke veiligheidsvoorschriftenGelieve deze “handleiding voor de eigenaar” te lezen

    •Lees deze instructies en let op alle waarschuwingen.•Gebruik dit toestel niet in de buurt van water.•Het toestel moet aangesloten worden aan een netcontactdoos met aarding.•Enkel reinigen met een vochtige doek.•Neem de nodige tijd om deze “handleiding voor de eigenaar” zorgvuldig door te lezen. Zo kunt u uw systeemcorrect instellen en bedienen, en nadien genieten van alle geavanceerde opties. Bewaar deze “handleiding voor deeigenaar” voor eventueel later gebruik.

    •Blokkeer niet de ventilatie openingen aan achterzijde van de subwoofer.•Plaats niet vlakbij warmtebronnen als radiatoren, fornuizen, ovens of andere warmteproducerende apparaten(inclusief versterkers).

    •Knoei niet met de geaarde netsteker. Gebruik alleen een op het stopcontact passende netsteker. Waarschuw meteenuw dealer wanneer de netsteker niet past.

    •Voorkom dat netkabel en pluggen bekneld of beschadigd raken.•Gebruik alleen aansluitmateriaal/accessoires die door KEF zijn gespecificeerd.•Koppel net- en antennepluggen los bij onweer of bij langdurige afwezigheid.•Laat serviceverlening over aan gekwalificeerd personeel. Laat het apparaat steeds door hen nakeijken wanneer denetkabel/plug is beschadigd, water of andere zaken in het apparaat zijn gevallen, het apparaat is blootgesteld aanregen of vocht, niet normaal werkt of is gevallen.

    •Wees voorzichtig bij elk vervoer van het apparaat, ook om letsel te voorkomen.•Het apparaat mag niet blootgesteld worden aan opspattend water. Bovendien mogen geen voorwerpen gevuld met

    WAARSCHUWINGGELIEVE DIT TOESTEL NIET BLOOT TE STELLEN AAN

    REGEN OF VOCHT TENEINDE HET RISICO VAN BRAND OFELEKTRISCHE SCHOKKEN TE BEPERKEN

    OPGELETNIET OPENEN:RISICO OP

    ELEKTRISCHESCHOKKEN

    Verklaring van Grafische Symbolen

    De bliksemschicht met pijl bovenaan, in een gelijkzijdige driehoek,dient om de gebruiker te wijzen op de aanwezigheid van nietgeïsoleerde “gevaarlijke spanning”in het product waardoor personen het risico lopen blootgesteld teworden aan elektrische schokken.

    Het uitroepingsteken in een gelijkzijdige driehoek dient om degebruiker te wijzen op belangrijke functie- en

    onderhoudsinstructies in de documenten die bij het toestel horen.

    OPGELET:GELIEVE DE DEKPLAAT(OF HET ACHTERPANEEL) NIET TE

    VERWIJDEREN TENEINDE HET RISICO VANELEKTRISCHE SCHOKKEN TE BEPERKEN.

    ONDERDELEN MOGEN NIET HERSTELDWORDEN DOOR DE GEBRUIKER.

    ONDERHOUD ENKEL UIT TE VOEREN DOOR

    CLASS 1 LASER PRODUCT

    KLASSE 1 LASERPRODUCT

    LUOKAN 1 LASER LAITE

    KLASS 1 LASER APPARAT

    Nederlandse handleiding

    KIT200_Manual.qxd 10/1/11 15:04 Page 8

  • 9

    (GB) Follow this manual carefully for best results(F) Veuillez vous conformer aux indications du présent manuel

    d’utilisation(D) Für optimale Ergebnisse mit Ihrer Anlage befolgen Sie bitte

    diese Anleitung

    (I) Seguire attentamente le istruzioni contenute in questomanuale

    (ES) Siga las instrucciones de este manual para obtener losmejores resultados

    (P) Siga rigorosamente este manual para obter os melhores

    (GB) Read and return warranty card(F) Veuillez lire et renvoyer la carte de garantie(D) Lesen Sie die Herstellergarantieanforderungskarte und

    senden Sie diese ausgefüllt zurück. D-A-CH bittebesondere Karte ausfüllen.

    (I) Si prega di restituire la scheda di garanzia, previa attentalettura

    (ES) Lea y envíenos la tarjeta de garantía(P) Leia e devolva o cartão de garantia(NL) U kunt na lezing en invulling de garantiekaart aan de

    importeur sturen

    (GB) Clean with a damp lint free cloth(F) Nettoyer à l’aide d’un chiffon humide, non pelucheux(D) Mit einem angefeuchteten, nicht fusselndem Tuch

    abwischen(I) Pulire con un panno umido non sfilacciato(ES) Limpie con un paño húmedo(P) Limpe com um pano húmido sem pêlos(NL) Reinigen met een vochtige niet pluizende doek

    (GB) Do not use spirit based cleaners(F) Ne pas utiliser d’agents nettoyants à base

    d’alcool(D) Keine alkoholhaltigen Reinigungsmittel

    verwenden(I) Non utilizzare prodotti a base di alcol(ES) No use limpiadores con base de alcohol(P) Não utilize produtos de limpeza à base de

    álcool

    (GB) Avoid direct sunlight(F) Eviter l’exposition directe aux rayons du soleil(D) Direktes Sonnenlicht vermeiden(I) Evitare l’esposizione diretta ai raggi del sole(ES) Evite la luz directa del sol(P) Evite a exposição directa à luz do sol(NL) Vermijd rechtstreeks zonlicht

    (GB) Avoid temperature extremes(F) Eviter les températures extrêmes(D) Extreme Temperaturen vermeiden(I) Evitare temperature troppo alte o troppo

    basse(ES) Evite temperaturas extremas(P) Evite temperaturas extremas(NL) Vermijd extreme temperaturen

    (GB) SAFETY NOTICE! trailing cables are dangerous, secure all cables(F) NOTE DE SECURITE ! Les câbles de haut-parleurs traînant sur le sol peuvent être source de danger. Fixer tous les câbles(D) SICHERHEITSHINWEIS ! Herumliegende Lautsprecherkabel sind eine Gefahrenquelle. Bitte alle Lautsprecherkabel sorgfältig verlegen(I) NOTA PER LA SICUREZZA: i cavi di uscita dei diffusori possono essere pericolosi se non sistemati in un posto sicuro(ES) ¡ATENCION! los cables de conexión sueltos de los altavoces son peligrosos. Fíjelos(P) Precauções de segurança! Os cabos das colunas espalhados são perigosos, fixe todos os cabos(NL) VOOR UW VEILIGHEID! Loshangende luidsprekerkabels zijn gevaarlijk! De kabels steeds op een veilige plaats leggen

    (GB) Avoid damp(F) Eviter l’humidité(D) Feuchtigkeit vermeiden(I) Evitare l’umidità(ES) Evite la humedad(P) Evite a humidade(NL) Vermijd vocht

    (F) points importants (D) Wichtige Hinweise (I) punti importanti (ES) puntos importantes (P) pontos importantes (NL) belangrijke

    aandachtspunten

    important points

    (GB) Read (F) ‘A lire’(D) Lesen(I) Leggere(ES) Lea(P) Leia(NL) Lees

    (GB) Correct(F) Correct(D) Richtig(I) Corretto(ES) Correcto(P) Correcto(NL) Juist

    (GB) Wrong(F) Incorrect(D) Falsch(I) Errato(ES) Incorrecto(P) Errado(NL) Fout

    (GB) Option(F) En option(D) Option(I) Opzione(ES) Opción(P) Opcional(NL) Optie

    (GB) Caution/Warning (F)

    Attention/Avertissement(D) Achtung / Warnung(I)

    Attenzione/Avvertenza(ES)

    Precaución/Atención(P) Atenção/ Aviso

    (GB) Electrical Warning(F) Danger électrique (D) Warnung: Gefährliche

    Spannungen(I) Rischi elettrici(ES) Advertencia eléctrica(P)Aviso sobre a parte eléctrica

    (GB) Positive/RED (F) Positif / ROUGE (D) Positiv / ROT(I) Positivo / ROSSO(ES) Positivo / ROJO(P) Positivo/Vermelho(NL) Positief / ROOD

    (GB) Negative/BLACK(F) Négatif / NOIR (D) Negativ /

    SCHWARZ(I) Negativo / NERO(ES) Negativo / NEGRO(P) Negativo/ Preto(NL) Negatief / ZWART

    The following icons are used throughout this manual to help you safely install your new DVD system. Please follow them carefully.GB

    F

    D

    I

    ES

    P

    NL

    Les icones suivantes sont utilisees dans ce manuel d’utilisation afin de vous aider a installer votre systeme DVD en toute securite.Veuillez

    Die folgenden Symbole finden Sie in der gesamten Anleitung. Sie erleichtern eine sichere Installation Ihrer neuen Anlage. Bitte achten Siesorgfältig aufQuesto manuale fa riferimento alle seguenti immagini per indicare come installare correttamente il sistema. Si raccomanda di seguirle con

    Se utilizan los iconos siguientes en este manual para ayudarle a instalar con seguridad sus nuevos altavoces. Sígalas cuidadosamente.

    Os ícones seguintes encontram-se ao longo deste manual de modo a ajudá-lo a instalar com segurança o seu novo sistema de DVD. Siga-os

    Allerwege in deze handleiding zijn de volgende iconen behulpzaam bij de veilige installatie van uw nieuwe DVD systeem Volg de instructies

    (F) utilisation du manuel (D) Verwendung der Anleitung (I) uso del manuale (ES) uso del manual (P) utilização do manual (NL) gebruik

    van de handleiding

    using the manual

    ES

    P

    NL

    GB

    F

    D

    I

    Thank you for purchasing the KIT200. We are confident that it willprovide reliable, high performance sound for many years to come.

    Nous vous remercions de la confiance que vous temoignez a KEF, LeKIT200 a été élaboré avec tout le soin nécéssaire et vous procurera delongues années de plaisir sonore et musical. Veuillez lire attentivement le

    Herzlichen Glückwunsch zum Kauf des KEF Instant DVD Theatre. Mitdiesen innovativen Geräten werden Sie viele Jahre Musik und Videos

    Grazie per aver acquistato il sistema KIT200. Siamo certi che visoddisferà pienamente per molti anni a venire. Leggete

    Gracias por adquirir el modelo KIT200. Un producto de calidadexcepcional capaz de garantizar un sonido de alta calidad por

    Muito obrigada por ter adquirido o KIT200. Estamos confiantes queele lhe irá oferecer, por muitos anos, um som de elevadaperformance, de confiança e de excelente qualidade. Leia por favor,

    Hartelijk dank voor aanschaf van de KIT200. Wij vertrouwen eropdat deze combinatie u jarenlang hoogwaardig luisterplezier zal blijven

    introduction(F) introduction (D) Einleitung (I) introduzione (ES) introducción (P) introdução (NL) inleiding

    KIT200_Manual.qxd 10/1/11 15:04 Page 9

  • 1 0

    quick start-up guide(F) guide de démarrage rapide (D) Kurzbedienungsanleitung (I) guida rapida per l’installazione (ES) guía rápida de procedimientos iniciales (P)

    manual de consulta rápida (NL) snelle opstartgids

    KIT200_Manual.qxd 10/1/11 15:04 Page 10

  • 1 1

    KIT200_Manual.qxd 10/1/11 15:04 Page 11

  • 1 2

    positioning speakers

    A

    B C

    D

    D

    AE

    (F) positionnement des haut-parleurs (D) Positionieren der Lautsprecher (I) posizionamento degli altoparlanti

    (ES) colocación de los altavoces (P) posicionamento das colunas (NL) plaatsing van de luidsprekers

    KIT200_Manual.qxd 10/1/11 15:04 Page 12

  • 1 3

    positioning subwoofer

    A B

    KIT200 KIT200 KIT200

    KIT200

    KIT200>150mm

    (F) positionnement du subwoofer (D) Positionieren des Subwoofers (I) posizionamento del subwoofer (ES) colocación del subwoofer (P)

    posicionamento do subwoofer (NL) plaatsing van de subwoofer

    KIT200_Manual.qxd 10/1/11 15:04 Page 13

  • 1 4

    wall mounting

    (GB) Warning - No attempt should be made to install these loudspeakers unless you are sure that you will not be cut-ting through electric cables, water or gas pipes, or sup-porting joists.

    (F) Avertissement - Avant de procéder à l’installation de cesH.P., vérifier bien que vous ne risquez à aucun moment desectionner des câbles électriques, des canalisations d’eauou de gaz ou toute autre élément de ce type.

    (D) Warnung - Diese Lautsprecher sollten wirklich nur dann ander Wand installiert werden, wenn Sie sicher sind, daß Sienicht Stromkabel, Wasserleitungen, Gasrohre oder T-Träger durchbohren oder durchschneiden.

    (I) Avvertenza - Non cercare d’installare gli altoparlanti primadi aver verificato l’assenza di cavi elettrici, tubazioni del-

    l’acqua e del gas e di travetti nella zona d’installazione.

    (F) Installation Murale (D) Schablone für Wandmontage (I) Montaggio a Parete (ES) Montage en Pared (P) Montagem na parede (NL)

    KIT200_Manual.qxd 10/1/11 15:04 Page 14

  • 1 5

    KIT200_Manual.qxd 10/1/11 15:04 Page 15

  • 1 6

    tv connection options

    scart

    composite

    S video

    (F) alternatives de connexion tv (D) Anschlussmöglichkeiten des Fernsehgerätes (I) opzioni per il collegamento tv (ES) opciones de conexión a

    tv

    KIT200_Manual.qxd 10/1/11 15:04 Page 16

  • 1 7

    component

    tv audio out

    1 2

    3 4

    am aerial set-up fm aerial set-up(F) configuration antenne am (D) Aufstellen der AM (Mittelwelle)-

    Antenne

    (I) configurazione dell’antenna am (ES) configuración de la antena de

    a m

    (F) configuration antenne fm (D) Aufstellen der FM (UKW)-Antenne

    (I) configurazione dell’antenna fm (ES) configuración de la antena de

    fm

    (P) configuração da antena de fm (NL) installatie van de fm antenne

    KIT200_Manual.qxd 10/1/11 15:04 Page 17

  • 1 8

    VCR

    Cable/Sat

    VCR

    Cable/Sat

    Line Out

    R L

    Line Out

    R L

    Line Out

    R L

    TV l\O

    TV l\O

    l\O

    l\O

    VCRLine Out

    TV l\O

    R L

    Line Out

    R L

    Cable/Sat

    Cable/Sat

    vcr/satellite advanced connection options(F) alternatives de connexion magnétoscope / satellite (D) Anschlussmöglichkeiten VCR/Sat-Receiver (I) opzioni avanzate per il collegamento del

    videoregistratore/ricevitore satellitare (ES) opciones de conexión avanzadas a vcr/satélite (P) opções avançadas para ligação vcr/satélite (NL)

    geavanceerde aansluitopties voor video/satelliet

    KIT200_Manual.qxd 10/1/11 15:04 Page 18

  • 1 9

    VCR

    Cable/Sat

    VCR

    Cable/Sat

    Line Out

    R L

    Line Out

    R L

    Line Out

    R L

    Line Out

    R L

    Cable/Sat

    S-VIDEO

    S-VIDEO

    S-VIDEO

    S-VIDEO

    Cable/Sat

    KIT200_Manual.qxd 10/1/11 15:04 Page 19

  • 2 0

    english instructions

    carton contents

    unpackingCarefully unpack your system. Save all packingmaterials, which provide the safest way to transportyour system as needed.

    WARNING: To avoid danger of suffocation, keep theplastic bags out of the reach of children. If any part ofthe system appears damaged, do not attempt to use it.Notify your authorised dealer immediately. Check to besure your system includes the parts shown.

    Note: Please make a note of the serial numbers on thebottom of the DVD unit and the rear of the subwoofer.Copy those numbers onto your warranty card and in thespace provided below.

    For your records Serial numbers are located on the bottomof the DVD unit and the rear of the Subwoofer module.

    DVD unit serial number:__________________________

    Subwoofer module serial number: __________________

    Dealer name: ________________________________

    Dealer phone: ________________________________

    Purchase date: ________________________________

    KIT200_Manual.qxd 10/1/11 15:04 Page 20

  • 2 1

    KEF AUDIO (UK)

    Eccleston Road, Tovil, Maidstone, Kent, ME15 6QP UK Telephone: +44 (0) 1622 672261 Fax: +44 (0)1622750653

    www.kef.com

    specifications

    Playback formats supported DVD, DVD-RW, DVD+RW, CD, CDR/RW, MP3 encoded CD

    Tuner section AM/FM with RDS facility (Europe only)

    Audio inputs cable/satellite, (analogue & optical digital) VCR and TV (analogue)

    Audio output optical digital

    Video inputs cable/satellite and VCR (S-video & composite)

    Video outputs SCART (Europe only), component with progressive scan, S-video andcomposite

    Aerial inputs FM & AM (included)

    Cabinet material die-cast zinc

    Finish High Gloss Black

    Display High Bloss Black finish, white VFD display

    Control infra-red remote control

    Dimensions including feet 59 x 324 x 262 mm

    Type Three way closed box

    Drive Units 1 x 75 mm (3 in.) UNI-Q®, 15 mm (0.6 in.) aluminium HF2 x 75 mm (3 in.) LF

    Crossover Frequencies 800 Hz - 5 kHz

    Frequency range (± 3 dB) 95 Hz - 30 kHz

    Sensitivity (2.83 V / 1 m) 87 dB

    Maximum Output 106 dB SPL @ 1 m

    Impedance 8

    Net Weight 2 kg (4.4 lbs)

    Dimensions m m 419 x 88 x 127

    ( Satellite H x W x D) in. 16.5 x 3.46 x 5.0

    Dimensions m m 88 x 419 x 127

    (Centre H x W x D) in. 3.46 x 16.5 x 5.0

    Finish High Gloss Black

    Design closed box powered subwoofer

    Drive units 250mm (10 in.) long-throw unit

    Amplifier Box high power amplifier channels for subwoofer and main speakers

    Finish Matt Black Vinyl with Gloss Black acrylic front panel

    Dimensions (H x W x D) 398 x 176 x 515 mm15.6 x 6.9 x 20.3 in.

    KEF AUDIO reserve the right, in line with continuous research and development, to amend or change specifications without prior notice. E. &O.E.

    KIT200 subwoofer

    KIT200 dvd

    KIT200 speakers

    KIT200_Manual.qxd 10/1/11 15:04 Page 21

  • 2 2

    KIT200DVD HOME ENTERTAINMENT SYSTEMKEF AUDIO(UK), MAIDSTONE, ENGLAND

    OPTICALAUDIO OUT

    Radio

    Connection Video output to TV Scart (Europeonly) Component, S-video or

    Composite

    DigitalAudiooutput

    Video inputs S-video Digital audio Audio inputs from

    DVDregion(code)

    Will display CD track number and its elapsedtime when a disc is playing or the frequency

    Radio PRESETnumber

    Output acoustic modeover ride indicator:STEREO / MOVIE

    Surround sound encodingcurrently being applied bythe system:DOLBY DIGITAL®

    When SLEEP isactivated, thetime until systemturn off is

    display

    dvd system controlsSTAND BYTurns the system in andout of stand by.

    SOURCEChanges to the nextsource selection with

    OPEN/CLOSEOpens and closesthe disc tray

    SKIP/PRESETSelects the next or previous chapter on aDVD, track on a CD or MP3 disc, pictureon a JPEG disc or radio station preset

    VOLUMEIncreases or decreases thesystem volume. Pressing alsounmutes the system if muted

    PLAY/PAUSEStarts the DVD or CD playing,if a disc is in. If already playingit will pause the disc; pressagain to resume playing

    STANDBY

    Selecting the correct input on your TVThe KEF Instant Theatre on-screen displays will only bepresent on your TV screen if the TV’s external input isproperly set to the correct input which is connected tothe DVD player.The video input selection is mostcommonly made on televisions by pressing the TV’sremote control button marked ‘TV/Video’, ‘Input’,‘AV in’or ‘Aux’.

    Selecting Component and Progressive DVD outputWhen using the component video connection to your TV(whether progressive or not) you must connect thecomposite video connection as well to allow you to set thecomponent option while the default DVD output is

    composite only. Once you have selected the componentoption in the DVDs video settings menu change the TVsinput source to compontent and then select progressive ifsupported by your TV.

    Video loop-throughThe KEF Instant Theatre only plays composite video inputson the composite video output and only plays SVideoinputs on the SVideo output.You will therefore need acomposite or an SVideo lead if you are using these asvideo sources.

    Record and Multi-room audio outputsStereo mode must be selected in the Audio menu when

    dvd rear panel

    video connection setup

    KIT200_Manual.qxd 10/1/11 15:04 Page 22

  • 2 3

    remote control

    OPEN/CLOSEOpens and closes the disc tray

    POWERTurns the system in and out of standby.

    DVD/CD/MP3Selects the built-in disc player

    AM/FMSelects the built-in FM and AM radiotunerand switches between FM and AM

    TVSelects TV as the sound source

    VCRSelects the video recorder as thesource for both sound and video

    CBL/SATELLITESelects the set-top box device as thesource for both sound and video

    BASS/ TREBLEDisplays the bass/treble controlmenu

    MUTEMutes and unmutes the systemvolume

    ± VOLUMEIncreases or decreases the systemvolume

    ± SUBWOOFER LEVELIncreases or decreases the level ofbass from the subwoofer

    ± SKIP/PRESETSelects the next or previous chapteron a DVD, track on a CD or MP3 disc,picture ona JPEG disc or radio station preset

    PLAYStarts the DVD or CD playing

    PAUSEPauses the disc. Press again toadvance the disc one frame

    STOPStops the disc playing. Press again togo back to the beginning of the disc

    REV/TUNE DOWNRewind x2, x4, x8 or x20. Radiomanuallytune down

    FAST/TUNE UPFast forward x2, x4,x8 or x20.Radio manually tune up

    CHAPTER/SEEK DOWNSelects the previous chapter, track,or picture. Radio auto tune down

    CHAPTER/SEEK UPSelects the next chapter, track, or

    picture. Radio auto tune up

    ANGLEChanges the DVD camera angle, ifavailable, and rotates a JPEG picture

    KIT200_Manual.qxd 10/1/11 15:04 Page 23

  • 2 4

    Settings MenuPress the SETTINGS button when watching video from the KEF Instant Theatre toview the Settings menu, provided the TV’s external AUX input is properly set toview the KEF Instant Theatre’s video output.Within the Settings menu, select acategory (Language, Video, Audio, or Ratings) with the left/right navigationarrow keys, and press SELECT to open that category’s menu.Within all the menus, select a category with the up/down navigation arrow keys,and press SELECT to open that category’s options. Then choose an option with theup/down navigation arrow keys and press SELECT. To back out of the menus usethe left and up navigation arrow keys.

    Language MenuThe Language menu provides for changing the language of all KEF Instant Theatresystem menus,and for indicating preferences for the language of the DVD’s soundtrack andmenus. (DVDs are published with a limited number of languages on any one disc;the disc will play in your selected language, if available, or in the default languagefor that disc.) Within the Language menu, select a category (Main menu, DVDsoundtrack, or DVD menu) with the up/down arrow keys, and press SELECT toopen that category’s options.

    Main MenuChoosing a language from this list will cause all KEF Instant Theatre system menus(including this one) to be displayed in that language.

    DVD SoundtrackDVD discs are often published with multiple alternate soundtracks for any one filmon that disc. Setting the DVD soundtrack language will use this sound track asdefault if it is present on the DVD. It is usually possible to override thispreference in the DVD disc’s own menu.

    DVD MenuThis will set the default DVD discs menu language if available on that DVD.

    Video MenuThe Video menu allows the KEF Instant Theatre to be optimised for use withdifferent TVs and different countries’ broadcast standards.

    TV TypeChoose the option that best describes the TV being used.

    Std.TV 4:3Choose ‘Std. TV 4:3’ for a TV with a screen ratio of 3/4 which will appearalmost as tall as it is wide but is fairly small. When a DVD is published with bothwidescreen (letterbox) and pan-and-scan video formats, this setting will cause itto play in pan-and-scan mode, expanding that part of the picture containing theaction to fill the entire screen.

    Bigscreen 4:3Choose ‘Bigscreen 4:3’ for a TV with a screen ratio 3/4 which will appear almostas tall as it is wide, and is fairly large. When a DVD is published with bothwidescreen (letterbox) and pan-and-scan video formats, this setting will cause itto play in widescreen mode, typically showing the entire widescreen film imageacross the centre of the screen, leaving the very top and bottom of the screenblank (black).

    Widescreen 16:9Choose ‘Widescreen 16:9’ for use with a true widescreen TV (with the screenalmost twice as wide as it is high). When a DVD includes the widescreen(letterbox) format, it will completely fill the screen. If a DVD is published withonly the pan-and-scan (traditional TV) video format, this setting will cause it tobe shown in the centre of the wide TV screen, with black filling in the emptyspace left and right of the picture.

    TV StandardTelevision programs are broadcast, and videos or DVDs are published, in differentformats in different countries. Choose the format that best matches the localvideo/broadcast environment.

    NTSCChoose this if all programming is per the NTSC standard. (Default for KEF Instant

    system settings

    KIT200_Manual.qxd 10/1/11 15:04 Page 24

  • 2 5

    Theatre systems sold in the USA.)

    PALChoose this if all programming is per the PAL standard. (This is the broadcaststandard across much of Europe and is the default for KEF Instant Theatresystems sold in the UK and Europe.)

    AutoChoose this if using a multi-standard TV and for programming that is a mixture ofNTSC and PAL,as in countries where DVDs might not all be published in the same format. DVD Output DVD Output determines which video output, in addition to Composite (RCA), willcarry video signals from the KEF Instant Theatre to your TV. (You will see aprompt message when selecting a new DVD output, highlight and SELECT “YES” toconfirm any changes to this setting. This is to prevent you setting an output videoformat which is not displayable on your TV). It should be noted that a SCART leadis provided in Europe because many TVs have this connection and it gives bettervideo quality.If using a SCART lead then the setting of DVD Output is not necessary.

    Composite/SChoose this setting if the KEF Instant Theatre will be connected to only theComposite (RCA) input or the S-Video input of the TV.

    ComponentChoose this setting if the KEF Instant Theatre will be connected to the Component(RGB) input of the TV. In this case, connect the Composite input as well, so thatyou can view non-DVD sources and to allow you to set the component andprogressive options whilst the default DVD output is composite and S-video only.When watching a DVD, switch the input of the TV to “Component” or “RGB.” (TheKEF Instant Theatre’s Component and S-video outputs cannot both be active at thesame time.) Component gives the best video quality for plasma, projector, orother component compatible televisions or monitors.

    ProgressiveSelect “On” if using the Component output for DVD programs with a TV thatsupports‘progressive scan’. Otherwise, select “off”. Progressive scan gives improvedpicture quality on a compatible monitor or television but must be used inconjunction with component DVD Output.It will output PAL or NTSC progressive output as defined by the source material.

    Audio MenuThe Audio menu allows for calibration of the KEF Instant Theatre for use inunusually shaped or furnished rooms, and for turning off the surround sound, ifthis should be desired. To adjust bass/treble use the dedicated buttons on theremote control.

    Surround SoundNormally, the default of “All purpose” is suitable for all users, but one maychoose another setting for surround sound as follows:

    Off (Stereo)Choose this setting to turn surround sound off. Stereo mode must be selected ifyou are using the ‘Record/multi room output’ on the rear of the subwoofer torecord or drive a separate pairof speakers.

    MatrixUse this setting to hear some degree of surround sound from monophonicrecordings and movies.

    MovieUse this setting to experience Dolby Pro Logic II Movie decoded audio whichproduces different surround effects for films and video games. Leave MOVIEswitched off if you are listening to MUSIC.

    All purposeAs the name suggests, this setting will optimise your system depending on whatprogram material is present with the exception of monophonic recordings. If thesource contains Dolby DigitalT M or DTST M signals then these will always play bydefault. Other sources will be played in a configuration of Prologic II chosen by

    KIT200_Manual.qxd 10/1/11 15:04 Page 25

  • 2 6

    Calibration MenuThe standard settings will already be correct for a normal room. The calibration menuallows you to test that the speakers are all connected and allows you to adjustindividual speaker levels if required for your individual room. Note: The calibrationoption will only appear if you are in ‘disc mode’ when youpress SETTINGS.

    Sitting in a central seat of the listening/viewing area, go to disc mode, highlight andSELECT “Calibration” to start the acoustic calibration process. Noise will emanate fromone channel, then the next, and the next, right around the listening/viewing area. Usethe up/down navigation arrow keys to adjust the volume of any channel that doesn’tappear to match the others. When all channels sound equally loud, press STOP or EXITon the remote to exit the menu. It is recommended that a Sound Pressure Level meter isused to measure the sound levels accurately. (Although it is possible to adjust thesubwoofer level during this process,KEF recommends only confirming that the subwoofer is working, but not attempting tomatch its level to that of the other speakers. It is best to make fine adjustments to thesubwoofer level using the remote control keys during normal listening.)

    Ratings MenuDVD discs can be published with audience rating information or with multiple versions ofthe video appropriate for different audiences. The ratings menu is designed to allowparents to limit what sortof DVD programs can be watched by other family members without the parents’ privatepassword. (Unfortunately, as of the publication date of this manual, many DVDs arepublished without rating information and will play regardless of the parental controlsetting.)

    PasswordIf the lock icon to the right is open, enter any 4-digit security code with the numericbuttons of the remote and press SELECT. This will engage the parental controls featureand lock out others from this menu.If the lock to the right is closed, the “Ratings” cannot be changed without first re-entering the previously set 4-digit code and pressing SELECT. (During playback of a discwith a higher rating, you will be prompted for your password, enter the same fourdigits, then press SELECT.)

    RatingsHighlight the current rating and make changes with the left/right arrow keys. Thenpress the up arrow once, enter a password, and press SELECT to lock out furtherchanges. Press the up arrow again or press SETTINGS or EXIT to leave the “Ratings”menu.

    Rating level Name Description MPAA rating

    European rating

    1 Child Safe Particularly suitable for children

    2 Universal General audiences G U

    3 PG Parental guidance PG PG

    4 PG>12 Parents strongly cautioned PG-13

    5 PG>15 May be suitable for mature teenagers

    PG-15

    6 Accompanied Restricted

  • 2 7

    The currently tuned radio station will be saved to the next available preset when youpress STORE/ERASE PRESET twice. Alternatively to save the radio station to aspecific preset, between 1 and 40, navigate to a free preset and then pressSTORE/ERASE PRESET twice. Highlight the “ll” symbols and press SELECTto go to the previous or next page of ten preset numbers.

    To erase a preset:The currently highlighted preset radio station will be removed if you pressSTORE/ERASE PRESET twice.

    RDS:In Europe, if a strong enough RDS signal is received from a radio station, then thatstations frequency value will be replaced by the RDS station identifier letering.

    Status MenuPressing STATUS INFO once will display elapsed and remaining time information of thecurrently playing DVD or CD on your TV’s screen. Press again for complete statusdisplay. Pressing a third timewill exit.

    Shuffle/Repeat MenuAccessed by pressing the SHUFFLE/REPEAT key on the remote control. Use thenavigation arrow keys to highlight the setting you wish to change, then press SELECT tochange the setting. Once satisfied with the settings, highlight “OK” and press SELECTonce more to save the changes. (Highlight and SELECT “Cancel,” or pressSHUFFLE/REPEAT, to discard any changes and exit the SHUFFLE/REPEAT screen.) Allshuffle/repeat settings revert to “Off” whenever a disc is ejected.

    ShuffleShuffle modifies the order in which the chapters or tracks of a disc will be played.Choose “Shuffle” to play them in random order, or “Program” to create a customordered list of chapters/tracks.Choose “on” to play the tracks of a CD or the chapters of a DVD title in random order.(A DVD ‘title’ is a single feature, of which there may be several on a disc; the mainfilm, in addition to any number ofbonus features.)

    Program (CD only) When “Program” is set and “OK” SELECTED, a screen appears listing all possible playpositions.(Highlight the “1”, then enter the chapter or track number that should play first;highlight the “2”, etc.)

    Play ProgramHighlight and SELECT “Play Program” to exit programming mode and play theprogrammed selections.(To exit this screen without programming any selections, simply press“SHUFFLE/REPEAT” twice.)

    Clear ProgramHighlight and SELECT “Clear All” to empty the list of programmed selections and startover.

    RepeatIf repeat is off then the current CD or DVD will play to the end of the disc and stop (thisis the default behaviour). As with shuffle, select “OK” to confirm all changes and exitthe shuffle/repeat menu or select “Cancel” to discard changes and exit theshuffle/repeat menu.

    Choose “Track” to repeat the currently playing CD track (song) indefinitely.Choose “Disc” to repeat the currently playing CD or DVD disc indefinitely.Choose “Chapter” to repeat the currently playing DVD chapter indefinitely.Choose “Title” to repeat the currently playing DVD title indefinitely. (A DVD “title” isa single feature,of which there may be several on a disc; the main film, in addition to any number ofbonus features.)

    KIT200_Manual.qxd 10/1/11 15:04 Page 27

  • 2 8

    dolby surround

    dts digital surround

    macrovision

    progressive scan output at 525p and 625p

    dvd region codes

    1. Dolby DigitalDolby Digital is the multi-channel digital signal format developed by Dolby Laboratories. Dolby Digital consists of upto “5.1” channels – front left, front right, centre, surround left, surround right and an additional channelexclusively reserved for additional deep bass sound effects. (The Low Frequency Effects (LFE) channel containing bassfrequencies of up to 120Hz). Unlike the analogue Dolby Pro Logic format, Dolby Digital’s channels can all contain fullrange sound information, from the lowest bass, up to the highest frequencies (22kHz). The signals within each channelare distinct from the others, allowing pinpoint sound imaging, and Dolby Digital offers tremendous dynamic rangefrom the most powerful sound effects to the quietest, softest sounds, free from noise and distortion.

    2. Dolby Pro Logic IIDolby Pro Logic II is a new multi-channel playback format developed by Dolby Laboratories using feedback logicsteering technology and offering improvements over conventional Dolby Pro Logic circuits. Dolby Pro Logic II can beused to decode not only sources recorded in Dolby Surround but also regular stereo sources into five channels (frontleft, front right, centre, surround left and surround right) to achieve surround sound. Whereas with conventionalDolby Pro Logic the surround channel playback frequency band was limited, Dolby Pro Logic II offers a wider bandrange (20Hz to 20kHz or greater). In addition the surround channels were monoaural (the surround left and rightchannels were the same) with previous Dolby Pro Logic, but with Dolby Pro Logic II they are played as stereo signals.

    3. Dolby SurroundThese are sources in which three or more channels of surround have been recorded as two channels using DolbySurround encoding technology. Dolby Surround is used for the sound tracks of movies recorded on DVDs, LDs andvideo cassettes to be played on VCRs, as well as for the stereo broadcast signals of FM radio, TV, satellitebroadcasts and cable TV. Decoding these signals with Dolby Pro Logic makes it possible to achieve multi-channelsurround playback. The signals can also be played on ordinary stereo equipment, in which case they provide normalstereo sound. There are two types of DVD Dolby SURROUND recording signals. 1) 2-channel PCM stereo signals 2) 2-channel Dolby Digital signals.The KEF Instant Theatre is manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the

    double-D symbol are trademarks of Dolby Laboratories.

    Digital Theatre Surround (also called simply DTS) is a multi-channel digital signal format developed by Digital TheatreSystems. DTS offers the same “5.1” playback channels as Dolby Digital (front left, front right and centre, surroundleft and surround right) as well as the stereo 2-channel mode. The signals for the different channels are fullyindependent, eliminating the risk of deterioration of sound quality due to interference between signals and crosstalk

    etc. DTS features a relatively higher bit rate as compared to Dolby Digital (1234 kbps for CDs and LDs, 1536 kbpsfor DVDs) so it operates with a relatively low compression rate. Because of this the amount of data is great, andwhen DTS playback is used in movie theatres, a separate CDROM synchronised with the film is played. With LDs andDVDs, there is of course no need for an extra disc;

    the pictures and sound can be recorded simultaneously on the same disc, so the discs can be handled in the same wayas discs with other formats. There are also music CDs recorded in DTS. These CDs include 5.1-channel surroundsignals (compared to two channels on current CDs). They do not include picture data, but they offer surround

    KIT200_Manual.qxd 10/1/11 15:04 Page 28

  • 2 9

    navigation helpguide

    taking care of your system

    DVD MENUDisplays the title menu of the currently loaded DVD disc. (The DVD player must beselected first, by pressing DVD/CD/MP3 on the remote.) Each disc menu will be differentbut typically allows you to play the disc, choosing different sound and picture formats,and going directly to any point in the film or video. Press DVD MENU again or press EXITto leave the menu and resume playing.

    EXITExits the KEF Instant Theatre’s settings menu or the DVD disc menu, and returns to thevideo/audio program. Exits without saving partially completed changes. Exit will alsobring up the currently playing DVD’s title menu if one is present on the disc. This cansometimes be different to the DVD’s top menu obtained by pressing the DVD menu button.

    Navigation arrow keysUse to move within any on-screen menu; both menus provided on DVD discs, as well asthe SETTINGS, BASS/TREBLE, SHUFFLE/REPEAT, AM/FM control, and MP3/Photo-browsing menus of your KEF Instant Theatre. Pressing one of the (up/down/left/right)arrow keys will move the highlight to the next item in the direction of the arrow.In the KEF Instant Theatre settings menu, you can back out of the submenus by usingeither the up or left arrow keys, as appropriate. (“On-screen” means on your TV’sscreen, provided the TV’s external input (Aux in) is properly set to view the KEF InstantTheatre DVD output.)

    SELECTAfter highlighting your desired menu choice using the navigation arrow keys, press theSELECT button to confirm your choice. SELECT can change to the next choice in a list ofoptions, as is the case in the KEF Instant Theatre’s shuffle/repeat menu. (When browsingcomputer CDs containing MP3 and/or JPEG files SELECT will play the currentlyhighlighted file.)

    BASS/ TREBLEDisplays the bass/treble control menu on the front panel display and on your TV. Use theup/down arrow keys to switch between bass and treble, and the left/right arrow keys toadjust each control. Press BASS/TREBLE again or wait 5 seconds to exit the menu.

    SETTINGSPressing the SETTINGS button when watching any source except your TV will bring up theSettings menu, which includes controls for Language, Video, Audio, and Ratings (parentalcontrol) functions. Use of this menu is entirely optional, as the out-of-the box defaultsettings will work fine for most customers. Press SETTINGS again, or press EXIT at anytime, to exit the settings menu. (Please note that the Settings menu is not available duringplayback of JPEG pictures.)

    STATUS INFOIn disc mode this will display information about the currently playing DVD or CD on your TV screen. Press once forsimple elapsed and remaining time display, press again for complete status display. Pressing a third time will exit.Cleaning your DVD system• Use only a soft, dry cloth to clean the outside surfaces of the DVD system• Do not use any sprays near the system. Do not use any solvents, chemicals, or cleaning solutions containingalcohol, ammonia, or abrasives• Do not allow any liquids to spill into any openings

    Cleaning the speakers• Clean the surface of your speakers with a soft, damp cloth. You can use an ammonia-free window cleaner on a softcloth to maintain the finish• Do not use any sprays near the speakers. Do not use any solvents, chemicals, or cleaning solutions containingalcohol, ammonia, or abrasives

    Handle discs by their edges toprevent fingerprints and scratches

    To remove stains or fingerprintsfrom the surface of a disc, use asoft and dry lint-free, cloth. Wipein straight movements from thecentre of the disc to the outside

    Do not use a circular motion toclean. Do not use any chemicalproducts; they can damage the disc

    Do not write on or attach labels tothe surface of a disc

    KIT200_Manual.qxd 10/1/11 15:04 Page 29

  • 3 0

    trouble shooting Error messages

    NO DISC Press OPEN/CLOSE and ensure that a disc has been correctly inserted into the DVD playerBAD DISC Check that the disc is inserted correctly with the label side upwards and that it is cleanINCORRECT REGION Check that the DVD region number matches that on the rear of the DVD player

    No powerIf there is no blue standby light, no response to pressing the ON/OFF button on the remote control or the POWERbutton on the DVD player

    •Make sure the system is switched on at the rear of the subwoofer speaker •Check that the cable between the subwoofer and the DVD player is correctly connected at both ends andscrewed tight

    •Check that the power cord is connected firmly at both ends•Unplug the power cord from the outlet for 30 seconds to allow the system to reset

    No sound•Make sure “mute” is not lit on the display – if it is then press mute on remote control•Increase the volume level•Check speaker cable is connected to the rear of the subwoofer and screwed tight. Check that the speaker cableis firmly pushed into each speaker

    •Check that the external connections are firmly inserted and that the correct source is chosen e.g.CBL/TV/VCR

    Sound with no picture•Check connections from the VCR and CBL source are correctly plugged into the rear of the DVD system•Ensure the television is switched on and that the video input selection of your television is set to the correctAV input. This can be done with the TV’s remote control, TV/VIDEO, INPUT or AUX IN buttons

    •If you had a picture before but have just connected a different TV and there is now no picture, then the DVDoutput settings of the DVD system may be incorrect for the new television – reset the DVD outputs to theiroriginal out-of-the-box settings (see resetting factory defaults below)

    • When using a Scart video connection to your TV you require a composite lead to view external sourcesconnected to the KEF Instant Theatre’s composite inputs. You require an S-video lead to view external inputsconnected to the KEF Instant Theatre’s S-video inputs

    Remote control not working•Check batteries and their polarity (+ and -)•Make sure the DVD player’s front panel is not covered and that the remote control is pointing at the DVDplayer

    Radio does not work/or has poor reception•Move the antennas further away from your television and other electrical equipment. The AM band is verysusceptible to interference from televisions

    •Ensure the AM and FM antennas are connected•Extend the antennas and adjust their position to improve radio reception•Ensure AM antenna is upright

    DVD or CD does not playAfter pressing DVD/CD button and waiting a few seconds, LOAD should appear as the disc’s format information isread by the DVD player

    •Make sure the disc is properly inserted – label side up - eject the disc and re-insert it again•Ensure disc is not dirty or scratched – clean the disc carefully•Check that the disc region code matches the label on the back of the DVD system

    Sound is distorted•Check speaker connections•Reduce level from other connected sources in case of interference

    Subwoofer sound too high/low•The level of bass from the subwoofer can be adjusted using the remote control

    Speech missing on the Record or Multi room output•Stereo mode must be selected to ensure that the centre channel is mixed onto the left and right Record/Multiroom outputs.In the setting menu select Audio and change surround sound to “off” (stereo)

    Resetting factory defaultsYour KEF Instant Theatre can be returned to its original out-of-the-box settings by pressing 3 buttons on theDVD players front panel at the same time:-Press ‘PLAY/PAUSE’ and ‘

  • 3 1

    glossary

    Customer serviceFor additional help in solving problems, follow the trouble shooting section then contact KEF ® customer service oryour local retailer.

    WarrantyThe KEF Instant Theatre system is covered by a limited non-transferable warranty. Details of the warranty areprovided on the warranty card thatcame with your system. Please fill out the information section on the card and return it.

    AccessoriesThe KEF Instant Theatre system shelf speakers are compatible with the optional KEF Instant Theatre speaker floorstands.

    Aspect ratio The shape of the rectangular picture on a TV set. It is the width of the picture relative to the height.Standard TV screens are currently one of two standards: 4:3 (original, 4 units wide by 3 units high) and 16:9(widescreen)

    Audio CDs The KEF Instant Theatre plays audio compact discs, CD-R and CD-RW recorded compact discs

    Chapter A DVD title or film is split into several chapters to allow simpler searching

    Component Connection system - usually between DVD player and display device such as TV or projector - in whichluminance is carried on one cable and the blue and green colours are each carried by their own cable. Connections inthis case is on a trio of phono sockets

    Composite video A single connection, for example between a DVD player and a TV, in which the whole picture signal(containing luminance, colour and synchronisation information) is carried in the PAL (Europe) or NTSC (America)formats. Usually with single phono sockets,generally coloured yellow to distinguish it from the other connections provided

    Dolby Digital Dolby Digital 5.1 is the standard means of encoding audio for DVD-Video. Dolby Digital is a trademark ofDolby Laboratories

    Dolby Prologic II Enhanced version of the original Pro-Logic, provides 5.1 channels of sound from a stereo inputsignal

    DTS DTS is a 5.1 multi-channel digital signal format developed by Digital Theater Systems. DTS is a trademark ofDigital Theater Systems

    DVDaudio This is a new DVD format which is not accepted on the KEF Instant Theatre DVD system although if otherformats are also present on the disc these will play

    DVDvideo Digital Versatile Disc (DVD) is an audio, video and data storage system based on laser read 12 or 8cmoptical discs. DVDvideo is a standard for storing video and audio information on DVD-ROM discs based on MPEG videoand audio encoding and compression. A DVD-ROM (Read Only Memory) can only be read and can not be written to

    IR An acronym for infrared. The remote control communicates to the DVD player with an infrared light beam sodirect line of sight is required for successful operation

    JPEG Allows viewing of pictures saved in JPEG (Joint Photographic Expert Group) format such as that derived fromdigital cameras

    Letterbox This describes the effect caused when video wider than 525 or 625 lines is shrunk to fit onto a TV withaspect ratio 4:3. It inserts black areas above and below the video window so that the window typically takes up thefull width of the TVs display

    MP3 MPEG 1 contains a Layer 3 audio compression scheme. This Layer 3 audio compression system is commonlyused for downloading music files from the Internet to a PC or MP3 recording device. It reduces file sizes by a factorof 12 to enable faster downloads. MP3 files saved on to a CD will be played in stereo irrespective of the surroundsound mode selected in the audio menu

    MPEG MPEG is a video compression standard defined by the Motion Picture Expert Group. It allows a large amountof video and audio digital data to be stored on a disc

    NTSC An acronym for National Television System Committee. It is the television picture format that is commonlyused in America

    PAL An acronym for Phase Alternate Line. It is the television picture format commonly used in Europe

    PCM An acronym for Pulse Code Modulation. An uncompressed, digitally coded, audio signal used on CDs andlaserdiscs

    RDS Radio Data Signature is used on VHF FM transmissions and provides a number of facilities of great informationto all listeners.This includes enabling the station name to be displayed on the radio display, which is used in the KEF Instant Theatre.It can also alert you when news, traffic, or specific program types are being transmitted, these are not accessibleon the KEF Instant Theatre

    KIT200_Manual.qxd 10/1/11 15:04 Page 31

  • 3 2

    instructions en français

    contenu du carton

    déballageDéballez soigneusement l’appareil. Conservez tout lematériel d’emballage car cela constitue le moyen le plusaisé pour le transportersi nécessaire.

    AVERTISSEMENT : Pour éviter tout risque d’étouffement,veuillez garder les sacs en plastique hors de portée desenfants.Si une des pièces du système semble endommagée,n’essayez pas de l’utiliser. Prévenez immédiatementvotre revendeur agréé.

    Vérifiez si votre enballage contient bien les élémentsillustrés.

    Remarque : Veuillez noter les numéros de série qui setrouvent au bas du DVD et à l’arrière du subwoofer.

    Copiez ces numéros sur votre carte de garantie ainsi qu’àl’endroit prévu à cet effet ci-dessous.

    Pour votre information Les numéros de série sont situés aubas du DVD et à l’arrière du module Subwoofer.Numéro de série du DVD : ______________________

    Numéro de série du subwoofer : __________________

    Nom du revendeur : ____________________________

    Téléphone du revendeur : ________________________

    Date d’achat : ________________________________

    KIT200_Manual.qxd 10/1/11 15:04 Page 32

  • 3 3

    KEF AUDIO (UK)

    Eccleston Road, Tovil, Maidstone, Kent, ME15 6QP UK Telephone: +44 (0) 1622 672261 Fax: +44 (0)1622750653

    www.kef.com

    caractéristiques techniques

    Formats de lecture supportés DVD, DVD-RW, DVD+RW, CD, CDR/RW, encodé au format MP3Fréquences radio AM/FM avec fonction RDS (en Europe uniquement)

    Entrées audio câble/satellite, magnétoscope (analogique & optique numérique) et TV(analogique)

    Sortie audio numérique optique

    Entrées vidéo câble/satellite, magnétoscope (S-vidéo & composite)

    Sorties vidéo peritel (Europe uniquement), composant, S-vidéo et composite

    Prises antenne FM & AM (comprise)

    Matériau boîtier zinc moulé sous pression

    Finition Laqué Noir

    Affichage Finition Laquée Noire, affichage VFD blanc

    Contrôle télécommande à infrarouge

    Dimensions pied compris 59 x 324 x 262 mm

    Type Enceinte close a 3 voies

    Haut-parleurs Ensemble Uni-Q 75 mm, avec tweeter 15 mm, 2 woofer de 75 mm (3in.)

    Fréquences de coupure 800 Hz - 5 kHz

    Réponse en fréquence (± 3dB) 100 Hz -30 kHz

    Sensibilité (2.83V/1m) 87 dB

    Puissance maximale (SPL) 106 dB SPL @ 1 m

    Impédance 8

    Poids 2 kg (4.4 lbs)

    Dimensions m m 419 x 88 x 127

    ( Satellite H x L x P) in. 16.5 x 3.46 x 5.0

    Dimensions m m 88 x 419 x 127

    (Central H x L x P) in. 3.46 x 16.5 x 5.0

    Design subwoofer actif clos

    Haut-parleurs Long débattement de 250mm

    Amplificateurs Boitier amplificateur pour le caisson de graves et les haut-parleursprincipaux.

    Finition Finition vinyle Noire mate, face avant en acrylique brillant.

    Dans un souci de continuité de la recherche et du développement, KEF Audio se réserve le droit de corriger ou modifier lescaractéristiques sans préavis.Sauf erreurs et/ou omissions

    KIT200 subwoofer

    KIT200 dvd

    KIT200 speakers

    KIT200_Manual.qxd 10/1/11 15:04 Page 33

  • 3 4

    KIT200DVD HOME ENTERTAINMENT SYSTEMKEF AUDIO(UK), MAIDSTONE, ENGLAND

    OPTICALAUDIO OUT

    Antennes

    Connexion au Sortie vidéo vers prise Peritel(Europe uniquement), S-vidéo ou

    composite

    Sortieaudio

    numérique

    Entrées vidéo S- Entrée audio

    RégionDVD(code)

    Affiche le numéro de piste du CD et le tempsécoulé lors de la lecture d’un disque ou la

    Numéro dePRESELECTION de

    Output acoustic modeover ride indicator:STEREO / MOVIE

    Encodage du son d’ambianceactuellement utilisé parl’appareil :DOLBY DIGITAL®

    ToucheDISCRETIONactivée

    Station sélectionnée, FMST, RDS et bande de Lorsque le mode

    SOMMEIL estactivé,le temps restant

    Sélection du canal adéquat sur votre télévisionLe menu à l’écran du système de divertissement KEFn’est présent à l’écran de votre téléviseur que si l’entréeexterne de la télévision est correctement réglée sur lecanal adéquat. La sélection de l’entrée vidéo s’effectuegénéralement sur les télévisions en appuyant sur lebouton de la télécommande de la télévision marqué ‘TV /Vidéo’, ‘Entrée’, ‘Entrée AV’ ou ‘Aux’.

    Sélection des sorties composant et progressif sur le DVD.Lorsque vous utilisez la connexion composant vers votretéléviseur (progressif ou pas), vous devez égalementbrancher la connexion vidéo composite pour vouspermettre de sélectionner l’option composant car, par

    défaut, le DVD est en sortie composite. Lorsque vous avezsélectionné l’option composant dans le menu vidéoDVD,sélectionnez l’entrée composant sur votre téléviseuret sélectionnez “progressif “ si votre téléviseur lepermet.

    Boucle Vidéo Le signal vidéo composite connecté sur l’entrée vidéocomposite sera restitué uniquement sur la sortie vidéocomposite, de même le signal entré sur la prise S Vidéone sera restitué que sur la sortie S Vidéo, vous aurezdonc besoin d’un câble composite ou S Vidéo si voussouhaitez utiliser ces sources vidéo.

    configuration de la connexion vidéo

    Entrées audio du boîtier de

    panneau arrière dvd

    écran

    commandes du dvdSTAND BYMet le systeme en veilleet hors veille.

    SOURCEPasse, lors de chaquepression, à la sélectionde source suivante

    OPEN/CLOSEOuvre et ferme leplateau du disque

    SKIP/PRESETSélectionnez le chapitre suivant ou précédent sur un DVD, la pistesuivante ou précédente d’un CD ou d’un disque MP3, l’imagesuivante ou précédente d’un disque au format JPG ou laprésélection précédenteou suivante d’une station de radio

    VOLUMEAugmente ou diminue le volume dusystème. Une pression sur ce boutonpermet également d’activer ou dedésactiver la fonction son discret

    PLAY/PAUSELance la lecture CD ou DVD si un disque estprésent. Si une lecture est déjà en cours, unepression sur ce bouton entraîne une pause.Appuyez à nouveau sur ce bouton pour reprendre

    STANDBY

    KIT200_Manual.qxd 10/1/11 15:04 Page 34

  • 3 5

    télécommande

    OPEN/CLOSEOuvre et ferme le plateau du disque

    POWERMet le systeme en veille et horsveille.

    DVD/CD/MP3Sélectionne le lecteur de disqueintégré

    AM/FMSélectionne le tuner radio FM et AMintégréet commute entre FM et AM

    TVSélectionne la TV comme sourcesonore

    VCRSélectionne le magnétoscope commelasource pour le son et la vidéo

    CBL/SATELLITESélectionne le boîtier de décodagecommela source pour le son et la vidéo

    BASS/ TREBLEAffiche le menu de réglage de latonalité (basses/aigues)

    MUTEActive et désactive la touche sondiscret

    ± VOLUMEAugmente ou diminue le volume dusystème

    ± SUBWOOFER LEVELAugmente ou diminue le niveau desbassesdu subwoofer

    ± SKIP/PRESETSélectionne le chapitre suivant ouprécédent sur un DVD, la pistesuivante ou précédente d’un CD oud’un disque MP3, l’image suivante ouprécédente d’un disque au format JPGou la présélection précédente ousuivante d’une station de radio

    PLAYDémarre la lecture du DVD ou du CD

    PAUSEEffectue une pause dans la lecture dudisque. Appuyez à nouveau sur cettetouche pour avancer le disque d’uneimage

    STOPInterrompt la lecture du disque.Appuyez à nouveau sur cette touchepour revenir au début du disque

    REV/TUNERéglage manuel de la radio vers lebas

    FAST/TUNEAvance rapide x2, x4,x8 ou x20.Réglage manuel de la radio vers lehaut

    CHAPTER/SEEK BASSélectionne le chapitre, la piste oul’image précédent. Réglageautomatique de la radio vers le bas

    CHAPTER/SEEK HAUTSélectionne le chapitre, la piste oul’image suivant. Réglage automatiquede la radio vers le haut

    ANGLEModifie l’angle de la caméra du DVD,si disponible, et pivote une imageJPEG

    KIT200_Manual.qxd 10/1/11 15:04 Page 35

  • 3 6

    Menu ParamètresAppuyez sur le bouton SETTINGS lorsque vous regardez la vidéo depuis le systèmeKEF pour afficher le menu Paramètres. Si l’entrée AUX externe de la télévisionest définie correctement pour voir la sortie vidéo du système KEF dans le menuParamètres, sélectionnez une catégorie (Langue, Vidéo, Audio ou Appréciation) àl’aide des touches de navigation gauche/droite et appuyez sur SELECT pour ouvrirle menu de cette catégorie.Dans tous les menus, sélectionnez une catégorie à l’aide des touches de navigationhaut/bas et appuyez sur SELECT pour ouvrir les options de cette catégorie.Choisissez ensuite une option à l’aide des touches de navigation haut/bas etappuyez sur SELECT. Pour quitter les menus, utilisez les touches de navigationhaut et bas.

    Menu LangueLe menu Langue permet de changer la langue de tous les menus du système KEF etd’indiquer vos préférences pour la