Institute of Bridge Engineering Civil, Structural and ...
Transcript of Institute of Bridge Engineering Civil, Structural and ...
Dr. Pinar Okumus, Assistant Professor Joshua Rodems, EIT, Graduate Student
Garrett Miller, Graduate Student
Institute of Bridge Engineering Civil, Structural and Environmental Engineering
University at Buffalo
April 19-24, Saratoga Springs, NY
Education
Professional Development
Research
www.buffalo.edu/bridge
Motivation
โข Cover Externally Bonded (EB) systems
โข Do not explicitly address Near-Surface Mounted (NSM) systems
Basis for AASHTO Guide Specs, 2012
Objectives
โข Review literature on NSM FRP Concrete
Strengthening
โข Evaluate AASHTO Guide Specifications,
2012 for NSM FRP
โข Prepare provisions for NSM FRP systems
to implement into the AASHTO Guide
Specifications, 2012
Groundwork
Includes both
โข EB Laminates
โข NSM Bars
Outline
Section 1-General Requirements
Section 2-Material Requirements
Section 3-Members under Flexure
Section 4-Members under Shear and Torsion
Section 5-Members under Combined Axial Force and Flexure
AASHTO Guide Specifications, 2012
Members under Flexure
1) The strain in the FRP system at FRP debonding / rupture:
๐๐๐๐ = tensile force in the FRP reinforcement
corresponding to an FRP strain of 0.005 AASHTO Guide
Specifications, 2012
ACI 440.2R ๐๐๐ = 0.083๐`๐
๐๐ธ๐๐ก๐ โค 0.9๐๐๐ข
๐๐๐ = 0.7๐๐๐ข
for FRP laminates
for NSM FRP
Members under Flexure
2) The development length, ld:
for FRP laminates
for FRP circular bars
for FRP rectangular bars
๐ฟ๐ โฅ๐๐๐๐
๐๐๐๐ก๐๐๐๐
๐๐๐ =๐๐
4 ๐๐๐๐๐
๐๐๐ =๐๐๐๐
2(๐๐ + ๐๐) ๐๐๐๐๐
๐๐๐ = 0.057๐๐ธ๐๐ก๐
๐`๐
AASHTO Guide
Specifications, 2012
ACI 440.2R
Outline
Section 1-General Requirements
Section 2-Material Requirements
Section 3-Members under Flexure
Section 4-Members under Shear and Torsion
Section 5-Members under Combined Axial Force and Flexure
AASHTO Guide Specifications, 2012
FRP Shear Strength
๐ฝ๐ = โ ๐ฝ๐ + ๐ฝ๐ + ๐ฝ๐ + โ ๐๐๐๐ฝ๐๐๐
โ ๐๐๐ = 0.85 (additional resistance factor for FRP only)
๐ฝ๐๐๐ = Nominal shear strength of FRP system
- Externally Bonded (EB): outlined explicitly
- Near-Surface Mounted (NSM): described but
no confirmed design methodology
Current design spec โ AASHTO 2012:
โข Strength of NSM FRP reinforced concrete beam:
- Mofidi et al (2012) โ 6 beams
- Wiwatrojanagul et. al (2012) โ 6 beams
- Cisneros et. al (2010) โ 8 beams
- Dias and Barros (2004 & 2006) โ 8 beams
โข Average bond stress and groove size:
- DeLorenzis and Nanni (2002) โ 22 tests
- DeLorenzis et. al (2002) โ 36 tests
- Mirmiran et. al (NCHRP 609, 2008) โ 12 tests
โข Total: 28 beams, 70 bond/pullout tests
Experimental Studies
Cisneros et. al (2010)
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
B90-3 B90-6 B45-3 B45-6 S90-3 S90-6 S45-3 S45-6
Str
eng
th I
ncr
ease
Beam Code
Shear Strength Increase due to NSM FRP
Key: B45-3
FRP incline angle
Number of FRP bars in given length
Experimental Studies
FRP Bar or Strip ๐๐ก๐๐๐๐๐กโ ๐ผ๐๐๐๐๐๐ ๐ =
๐น๐๐๐๐ข๐๐ ๐โ๐๐๐ (๐ค๐๐กโ ๐๐๐ ๐น๐ ๐)
๐น๐๐๐๐ข๐๐ ๐โ๐๐๐ (๐ค๐๐กโ๐๐ข๐ก ๐น๐ ๐)
Experimental Studies
Beam S45-3: Cisneros et al (2010) Typical Test Setup
Two-Opposite-Side
Experimental Studies
โข Experimental Failure Shear
โข 2012 AASHTO Guide Spec: Bonded FRP Systems
- Rupture failure
- Nonrupture failure
โข FRP Draft Spec: EB Systems (ACI 440.2R-08)
โข Near-Surface Mounted: De Lorenzis & Nanni (2001)
โข Others investigated by not practical for code use
Graphical comparison of shear strength:
โ ๐๐๐ = 0.85
Cisneros et. al (2010)
0.0
5.0
10.0
15.0
20.0
25.0
30.0
35.0
40.0
45.0
50.0
B90-3 B90-6 B45-3 B45-6 S90-3 S90-6 S45-3 S45-6
Sh
ea
r F
or
ce
(k
ips
)
Beam Code
Comparison of Calculated and Actual Shear Strength (Vn)
Failure Load
Calculated Strength - 2012 AASHTO, Rupture Failure
Calculated Strength - 2012 AASHTO, Nonrupture Failure
Calculated Strength - ACI 440.2R-08
Calculated Strength - De Lorenzis & Nanni NSM (2001) Tb = 1.00 ksi
Cisneros et. al (2010)
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
B90-3 B90-6 B45-3 B45-6 S90-3 S90-6 S45-3 S45-6
Sh
ea
r F
or
ce
(k
ips
)
Beam Code
Comparison of FRP Shear Strength (Vfrp)
2012 AASHTO, Rupture Failure 2012 AASHTO, Nonrupture Failure ACI 440.2R-08 De Lorenzis & Nanni NSM (2001)
0
10
20
30
40
50
60
70
0 10 20 30 40 50 60 70Ca
lcu
late
d S
hea
r S
tren
gth
(k
)
Experimentally Measured Shear Force at Failure (k)
Calculated Strength vs Actual Strength: 2012 AASHTO, Rupture Failure
Cisneros et al (2010) Wiwatrojanagul et al (2012)
Mofidi et al (2012) Dias and Barros (2004)
Calculated Strength = Failure Load
Over-estimated
Under-estimated
Shear strength over-estimated
Shear strength under-estimated
0
10
20
30
40
50
60
70
0 10 20 30 40 50 60 70Ca
lcu
late
d S
hea
r S
tren
gth
(k
)
Experimentally Measured Shear Force at Failure (k)
Calculated Strength vs Actual Strength: 2012 AASHTO, Nonupture Failure
Cisneros et al (2010) Wiwatrojanagul et al (2012)
Mofidi et al (2012) Dias and Barros (2004)
Calculated Strength = Failure Load
Over-estimated
Under-estimated
0
10
20
30
40
50
60
70
0 10 20 30 40 50 60 70Ca
lcu
late
d S
hea
r S
tren
gth
(k
)
Experimentally Measured Shear Force at Failure (k)
Calculated Strength vs Actual Strength: Draft Spec (ACI 440.2R-08)
Cisneros et al (2010) Wiwatrojanagul et al (2012)
Mofidi et al (2012) Dias and Barros (2004)
Calculated Strength = Failure Load
Over-estimated
Under-estimated
0
10
20
30
40
50
60
70
0 10 20 30 40 50 60 70Ca
lcu
late
d S
hea
r S
tren
gth
(k
)
Experimentally Measured Shear Force at Failure (k)
Calculated Strength vs Actual Strength: NSM โ De Lorenzis & Nanni (2001)
Cisneros et al (2010) Wiwatrojanagul et al (2012)
Mofidi et al (2012) Dias and Barros (2004)
Calculated Strength = Failure Load
Over-estimated
Under-estimated
0
2
4
6
8
10
12
14
16
1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80
Ex
per
imen
tal
Pu
llo
ut
Lo
ad
(k
)
Groove Ratio, k = Groove Depth/Bar Diameter
Groove Ratio vs Pullout Strength
DeLorenzis & Nanni (2002) DeLorenzis et al - Epoxy (2002) Optimum Groove Size (min) Optimum Groove Size (max)
0.00
0.50
1.00
1.50
2.00
2.50
3.00
1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00
Av
era
ge
Bo
nd
Str
ess
(ksi
)
Groove Ratio, k = Groove Depth/Bar Diameter
Groove Ratio vs Average Bond Stress
DeLorenzis & Nanni (2002) DeLorenzis et al - Epoxy-Conc Interface (2002)
DeLorenzis et al - Epoxy-Bar Interface (2002) Optimum Groove Size (min)
Optimum Groove Size (max) Average Bond Stress, Tb = 1.0 ksi
Shear Strength Equation: De Lorenzis & Nanni (2001)
The term Vf shall be determined as:
For round bars: ๐ฝ๐ = ๐๐ ๐ ๐๐๐๐ณ๐๐๐
where:
db = diameter of NSM FRP bar (in)
ฯb = average bond stress of NSM FRP reinforcing (ksi).
(May be taken as 1.0 ksi).
Ltot = total length of NSM FRP bars crossed by a 45ยฐshear crack (in)
The term Vf shall be determined as:
For rectangular bars: ๐ฝ๐ = ๐ ๐๐ + ๐๐ ๐๐๐ณ๐๐๐
where:
ab = smallest cross-sectional dimension of NSM FRP bar (in)
bb = largest cross-sectional dimension of NSM FRP bar (in)
ฯb = average bond stress of NSM FRP reinforcing (ksi).
(May be taken as 1.0 ksi).
Ltot = total length of NSM FRP bars crossed by a 45ยฐshear crack (in)
Shear Strength Equation: De Lorenzis & Nanni (2001)
The term ฯb (average bond stress) specified in the
nominal shear strength equations:
โข Direct relationship to shear strength
โข Experimental data shows can be taken as 1.0 ksi
โข Further testing can produce results > 1.0 ksi
(permissible to use in design).
Shear Strength Equation: De Lorenzis & Nanni (2001)
FRP spacing and incline
Shear Strength Equation: De Lorenzis & Nanni (2001)
l0.004 = length of NSM FRP bar based on limiting
strain in the FRP to 0.004.
lnet = Net length of NSM FRP bar used for reinf. (in).
n = the number of FRP bars crossed by a single
45ยฐshear crack (integer).
- calculated in manner that prevents a
longer bonded length from over-
estimating shear capacity (Vn).
Shear Strength Equation: De Lorenzis & Nanni (2001)
L4
L3 L
2
L1
Vn based on 45-degree shear cracks:
- Mild steel only โ accurate
- Prestressing steel presentโ conservative (ฮฑ < 45ยฐ)
n = 4
Shear Strength Equation: De Lorenzis & Nanni (2001)
Groove Size โข Groove size has impact on average bond stress
โข Constructability vs. optimum bond
โข Round bars:
Optimum groove size: 1.5 to 2.0 db
Maximum groove size: 2.0 db
โข Rectangular bars:
Optimum groove size: 1.5 to 2.0 ab and bb
Maximum groove size: 3.0 ab and 2.0 bb
- ACI 440.2R-08 (13.3) and Nanni et. al (2004)
โข Tolerance: +/- 1/8โ for 9/16โ groove is OK
- Mirmiran et. al, NCHRP Report 609 (2008)
Groove Size
High aspect
rectangular bar
Standard
circular bar
Steel Stirrup
(typ.)
ACI 440.2R-08 (13.3) and Nanni et. al (2004)
[+/- 1/8โ tolerance]
Conclusions
โข NSM FRP can increase Vn significantly depending on
beam characteristics & FRP properties and spacing.
โข Current AASHTO Guide Spec can estimate Vf for
NSM FRP but De Lorenzis & Nanni (2001) method
has explicitly outlined a reliable design procedure.
โข Draft code language was prepared on:
o Debonding/rupture strain
o Development length
o Shear strength contribution of NSM FRP
o Groove size
Conclusions โข Optimum groove size = 1.5 to 2.0x bar width unless
constructability is a factor (Max = 3.0x).
โข 1/8โ +/- tolerance for 9/16โ groove size OK
โข The FRP failure mode changes from epoxy splitting
to concrete splitting as groove size is increased for
both FRP bars and strips.
โข Best bond - epoxy adhesive (vs alternatives)
โข Experimental testing can be used to obtain
increased values for avg. bond stress (ฯb) higher
calculated shear strength.
Recommended Actions
โข Extend the literature review, cover chapters of
the AASHTO Guide Specifications, 2012 other
than flexure and shear
โข Conduct research to fill knowledge gaps such as
the ones on prestressed concrete and torsion,
generate more test data
โข Draft additional code language that will be added
to the AASHTO Guide Specifications, 2012
โข Develop design examples for NSM FRP
Strengthening
References
AASHTO, 2012. Guide Specifications for Design of Bonded FRP Systems for Repair and Strengthening of Concrete Bridge Elements, 1st ed. American Association of State Highway and Transportation Officials, Washington D.C. 2012.
ACI Committee 440. 2008. Guide to the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, ACI 440.2R-08, American Concrete Institute, Farmington Hills, MI.
Barros, J. A. O., Dias, S. J. E., โShear Strengthening of RC Beams with Near-Surface-Mounted CFRP Laminates.โ 7th International Symposium on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures (FRP7RCS), Kansas, USA, Vol. 1, pp. 807-823. 2005.
Cisneros, D., Artega, A., De Diego, A., Alzate, A., Ricardo, P., 2012, โExperimental Study on NSM FRP Shear Retrofitting of RC Beams.โ 6th International Conference on FRP Composites in Civil Engineering (CICE2012), Rome, Italy, 13-15 June.
De Lorenzis, L., Nanni, A., 2001. โShear Strengthening of Reinforced Concrete Beams with Near-Surface Mounted Fiber-Reinforced Polymer Rods,โ ACI Structural Journal, Vol. 98, No. 1, pp. 60-68. American Concrete Institute, Farmington Hills, MI.
De Lorenzis, L., Nanni, A. 2002. โBond Between Near-Surface Mounted FRP Rods and Concrete in Structural Strengthening.โ ACI Structures Journal, Vol. 99, No. 2, March-April 2002, pp. 123-133.
De Lorenzis, L., Rizzo, A., and La Tegola, A., (2002). โA Modified Pull-out Test for Bond of Near-Surface Mounted FRP Rods in Concrete.โ Composites, Part B, 33(8), 589-603.
Mofidi, A., Chaallal, O., Benmokrane, B., Neale, K., โExperimental Tests and Design Model for RC Beams Strengthened in Shear Using the Embedded Through-Section FRP Method.โ Journal of Composites for Construction, Vol. 16, No. 5, October 2012, American Society of Civil Engineers.
Nanni, A., Parretti, R., โStrengthening of RC Members Using Near-Surface Mounted FRP Composites: Design Overview.โ Advances in Structural Engineering, Vol. 7 No. 5, 2004.
NCHRP. 2008. Recommended Construction Specifications and Process Control Manual for Repair and Retrofit of Concrete Structures Using Bonded FRP Composites, NCHRP Report 609. Transportation Research Board, National Research Council, Washington, DC.
NCHRP. 2011. Design of FRP Systems for Strengthening Concrete Girders in Shear, NCHRP Report 678. Transportation Research Board, National Research Council, Washington, DC.
Wiwatrojanagul, P., Ayudhya, B. I.N., Sahamitmongkol, R., โNSM FRP Shear Strengthening of RC Beams with Internal Stirrups.โ Thammasat International Journal of Science and Technology, Vol. 17, No. 1, January-March 2012.
Thank You
Pinar Okumus, PhD
Joshua Rodems, EIT
www.buffalo.edu/bridge
๐๐๐๐ = ๐๐ ๐๐๐ ๐ถ๐ โ ๐๐
๐๐ = ๐๐๐๐๐๐ ๐๐ ๐ต๐บ๐ด ๐ญ๐น๐ท ๐๐๐
๐ =
๐๐๐๐ ๐ +๐
๐ญ๐๐ง ๐ถ๐
๐๐
๐๐.๐๐๐ = ๐. ๐๐๐๐ ๐๐ฌ๐
๐๐
Proposed Design Equations (circular bars):
Proposed Shear Strength Equation: De Lorenzis & Nanni NSM (2001)
Proposed Design Equations (circular bars):
๐ณ๐ =
๐๐
๐๐๐ ๐ถ๐ + ๐๐๐ ๐ถ๐
๐ โค ๐๐.๐๐๐ ๐๐๐ ๐ โค ๐ โค๐
๐
๐๐๐๐ โ๐๐
๐๐๐ ๐ถ๐ + ๐๐๐ ๐ถ๐
๐ โค ๐๐.๐๐๐ ๐๐๐ ๐
๐ < ๐ โค ๐
๐ณ๐๐๐ = ๐ฎ๐ณ๐
๐ฝ๐ = ๐๐ ๐ ๐๐๐๐ณ๐๐๐
๐๐๐๐ = ๐๐ โ๐๐
๐ฌ๐ข๐ง ๐ถ๐
Proposed Shear Strength Equation: De Lorenzis & Nanni NSM (2001)