1

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

Cable Cubby 650 UT • Installation Guide

This guide provides instructions for an experienced installer to install and connect the Extron Cable Cubby 650 UT.

The Cable Cubby 650 UT units are under furniture mountable and are expandable for cable access, connections, and AC power.

Planning

Check with local and state regulations before starting the installation

� Ensure that the planned installation complies with building and electrical codes.

� Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.

Check all parts and equipment before installation � Ensure that all parts are present in each kit.

� Ensure that necessary tools and equipment are available for the installation.

� Determine the number for Cable Cubby 650 UT enclosures you intend to install.

Kit Contents

125V~ 12A MAX TOTAL

Cable Cubby 650 UT

1

4

1

1

(6) 3/8", (2) 1/4"

1

1

4#6 Pan-head Mounting

Screws and Star Washers

AAP Frame Plate

Cable Grommet Plate

Connectivity Bracket

Connectivity Bracket

AAP Frame Plate

Cable Grommet Plate

#6 Pan-head Mounting Screws and Star Washers

Hole PlugsHole Plugs

#4-40 Module Screws

#4-40 Module Screws

Retractor Bracket

Retractor Pin & Clip

Retractor Pin and Clip

Cable Cubby 650 UT • Installation Guide (Continued)

2

Preparing the Table

Cut a hole in the surface where the enclosure will be installed. The size of the hole depends on the number of enclosures used (see cut-out dimensions on the next page). Ensure the sides of the hole are smooth after cutting and finished before installing. Read the following information before making a cut.

Determine the best location for the enclosure

� Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.

� Ensure that there is ample space under the table for cables. Allow at least 36 inches of cable loop for each cable (see Routing and Connecting Cables on page 7).

� When installing Retractors in the Cable Cubby, ensure that there is enough space for the Retractor assembly under the table or furniture.

22.95"(583 mm)

26.47"(672 mm)

21.28"(540 mm)

12.23"(311 mm)

9.23"(234 mm)

30

30

Table Top

Series/2

Series/2

9.0"(229 mm)

15.14"(385 mm)

21.14"(537 mm)

Series/2 XL

Series/2 XL

3.0"(76 mm)

3.0"(76 mm)

28.95"(735 mm)

NOTES:• To prevent objects from impeding cable retraction, allow at least 3 inches of clearance from the exposed cable side of

the enclosure (see the diagrams below).• Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact or

entanglement (see Routing and Connecting Cables on page 7).

3

Cut the hole in the table and pre-drill mounting holes

CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.

ATTENTION : Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut conduire à une blessure à l’oeil.

ATTENTION: The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople. Exercise care to prevent scarring or damaging the furniture.

ATTENTION : L’ouverture dans la table pour le Cable Cubby devrait être coupée seulement par des artisans autorisés et qualifiés. Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.

For one or two enclosures, the cut-out dimensions and mounting hole locations are shown below. For more enclosures, multiply the length accordingly. If necessary, pre-drill into the furniture at the keyhole and mounting hole locations.

NOTE: Diagrams shown above are not drawn to scale.

Dimensions and cut-out templates are available online at www.extron.com.

10"(254 mm)

SURFACE CUT-OUT

AREA1/16" (1.5 mm)

4 1/4"(108 mm)

+-

Mounting Holes (16)

11.5"(292 mm)

12"(305 mm)

5"(127 mm)

SURFACE CUT-OUT

AREA1/16" (1.5 mm)

4 1/4"(108 mm)

+-

1.5"(38 mm)

7"(178 mm)

1.5"(38 mm)

3"(76 mm)

6"(152 mm)

6.5"(165 mm)

6.5"(165 mm)

Mounting Holes (8)

6"(152 mm)

6.5"(165 mm) 3"

(76 mm)

1.5"(38 mm)

1.5"(38 mm)

Keyholes (4)

Keyholes (2)

2.0"(51 mm)

4

Option 2: Cable Pass-Through Module

Secure the grommet plate on the connectivity bracket, using four of the provided module screws.

2

Insert cables through the bottom of the connectivitybracket and into the holes of the grommet plate.

Snap the included hole plugs into any unused holes.

1

3

Insert “Show Me” Cables into the grommet plate.

1 Attach the “Show Me” Cable Trim Plateto the top of the module, using the module screws.

2

Attach the grommet plate to the bottom of the module, using the module screws.

3

Option 3: Retractor Bracket

Secure the bracket using four of the provided pan-head mounting screws with star washers. Tighten the screws using a screwdriver.

Insert the bracket as shown.

The bracket may be installed on the left or right side of the enclosure and at the lowest height.

2

1

left the

Preparing the Cable CubbyStep 1 (Only for multiple enclosures) — Assemble Enclosures

Option 1: AAP Module

Secure up to three single-space AAPs in the AAP plate.

Secure the AAP plate on the connectivity brackets, using four of the provided module screws.

#4-40 Nut with Captive Washer

Insert cables through the bottom of the connectivity bracket. Connect cables to the AAPs.

1

3

2

Step 2 — Assemble Connectivity ModulesConnectivity modules allow you to populate the Cable Cubby enclosure with a combination of AAPs, cable pass-through, or Retractors. Follow the steps below to assemble the connectivity modules of your choice.

Using a #2 screw driver, unscrew the four pan-head screws that attach the enclosure sides of the Cable Cubby together.Repeat this step on the corresponding side of the other enclosure.

Detach side panels of both enclosures.

1

Before attaching the enclosure, ensure the keyhole mounting holes are orientated in the same direction.

Attach the enclosures togetherwith the four pan-head mounting screwsand washers that were removed in step 1.

2

Repeat steps 1 and 2 to add more enclosures to the extension.

3

NOTE: The opening of the bracket should be installed towards the outside of the enclosure.

5

Cable Cubby 650 UT • Installation Guide (Continued)

125V~ 12A MAX TOTAL

Secure the modules using four of the provided pan-head mounting screws and star washers.

2

Insert the modules into the Cable Cubby.

1

Step 3 — Install the ModulesDetermine where the connectivity module and/or power module will be installed in the Cable Cubby. The modules may be installed on the left or right side of the enclosure and at various heights.

For the power module:

WARNING: Risk of Electric Shock. To ensure proper electrical grounding, use the provided #6-32 mounting screws with the star washers.

AVERTISSEMENT : Risque de choc électrique. Afin d’assurer une mise à la terre correcte, utilisez les fixations de mise à la terre #6-32 et les rondelles en étoile fournies.

125V~ 12A MAX TOTAL

125V~ 12A MAX TOTAL

2 Hook the Cable Cubby assembly onto the screws at the keyhole locations, as shown at right.

Slide the Cable Cubby assembly into slot.

Align the other mounting holes on the assembly with the pre-drilled holes on the furniture.

Tighten the screws to secure the Cable Cubby assembly.

Insert a mounting screw appropriate for the furniture material into each of the keyhole locations.Tighten each screw until it protrudes 1/4 inch from the bottom of the table.

1

3 Insert and tighten the rest of the mounting screws through remaining mounting holes on the enclosureand into the pre-drilled holes in the furniture.

Mounting holes

Mounting the Cable Cubby under the TableAlign the enclosure with the pre-drilled holes under the furniture. Secure the enclosure with the appropriate screws (see Cut the hole in the table and pre-drill mounting holes on page 3).

6

Cable Cubby 650 UT • Installation Guide (Continued)

Angular MountingRemove the enclosure screws as shown above, then follow this step:

Horizontal Mounting

See the Cable Retractor Setup Guide, available on the Extron website, for additional steps.

Remove two enclosure screws (one on each side) from this position. Then, mount the Retractors as shown at left.

Cable ReleaseAssembly

Move the cable release assembly upward until the angular mounting hole is visible. Reinstall the enclosure screws in this hole (both sides).

Remove two enclosure screws (one on each side) from this position. Then, mount the Retractors as shown at left.

Cable ReleaseAssembly

Move the cable release assembly upward until the angular mounting hole is visible. Reinstall the enclosure screws in this hole (both sides).

Installing RetractorsFollow the steps below to install Retractors. For horizontal or angular Retractor mounting, see the information below at right, then follow the steps below.

Insert the included pin through the Retractor mounting hole on the side of the Retractor assembly bracket.

Secure the clip to the pin.

Insert Retractors into the Retractor bracket. Secure the locking screw

on each Retractor. Do not overtighten.

2

3

14

Optional Double Retractor bracket mounting:

Install brackets as shown at right. Two double Retractor brackets can mount up to four Retractors.

Alternative Retractor Configuration for Cable Cubby 650 UT

Cable Cubby 650UTSide View

EE

Secure the brackets using four of the provided pan-head mounting screws with star washers. Tighten the screws using a screwdriver.

Insert the brackets as shown.

The bracket may be installed onthe left or right side of the enclosureand at the lowest height.

2

1

e

7

Routing and Connecting Cables

For cable pass-through applications, allow at least 36 inches (0.9 m) of cable loop for each cable.

Connect cables to the AV system and connect the AC power cord.

Using zip ties, secure cables to the holes on the bottom of the Cable Cubby.

1

2

3

NOTE: Ensure that there is no tension on the power cable.

CAUTION: Risk of Electric Shock. This equipment must be grounded.

ATTENTION : Risque de choc électrique. Cet équipement doit être fixé au sol.

Installation ChecklistPlanning (page 1)

� Check with local and state regulations before starting the installation

� Check all parts and equipment before installation

� Determine number of enclosures to install

Preparing the Table (page 2) � Determine the best location for the enclosure

� Verify sufficient space under furniture

� Cut a hole in the table and pre-drill mounting holes (page 3)

Preparing the Cable Cubby (page 4) � If applicable, assemble enclosures

� Assemble connectivity modules

� Install the modules (page 5)

Mounting the Cable Cubby (page 5) � Mount the Cable Cubby under the table

Installing Retractors (page 6) � Remove Retractor screws for horizontal and angular mount applications

� Install Retractors into the bracket

Routing and Connecting cables (page 7) � Dress cables under the table

� Connect cables to the AV system

8

68-3062-50 Rev. A04 17

Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe+800.3987.6673 (Inside Europe Only)

+31.33.453.4040 +31.33.453.4050 FAX

Extron Asia+65.6383.4400+65.6383.4664 FAX

Extron Japan+81.3.3511.7655+81.3.3511.7656 FAX

Extron China+86.21.3760.1568 +86.21.3760.1566 FAX

Extron Middle East+971.4.299.1800+971.4.299.1880 FAX

Extron Australia+61.8.8113.6800+61.8.8351.2511 FAX

Extron India1800.3070.3777 (Inside India Only)

+91.80.3055.3777 +91.80.3055.3737 FAX

© 2017 Extron Electronics All rights reserved. www.extron.com