HV Probe NAT 111 4018 HV Reference cableAT 111 4056
1
Objednací číslo AT 505 5001 ATAL spol. s r.o. Lesní 47, Tábor - Horky, 390 01, Czech Republic Phone: +420 381 251 791, Fax: +420 381 253 043 e-mail: [email protected]; web: http://www.atal.cz H H V V P P r r o o b b e e N N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A A T T 1 1 1 1 1 1 4 4 0 0 1 1 8 8 H H H V V V R R R e e e f f f e e e r r r e e e n n n c c c e e e c c c a a a b b b l l l e e e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A A A T T T 1 1 1 1 1 1 1 1 1 4 4 4 0 0 0 5 5 5 6 6 6 „HV probe N“ is used for measuring of the high voltage on the spark plugs by fitting the vehicle HV cable. Option for Multi-Diag Scope Multi-make Diagnostics Reference AT 111 4018, AT 111 4056 HV-probe-N-prospectus-en.doc The right is reserved to change this document (text and photos) ref.P111 0318 29.6.2011 During measuring on HV cables, when is required measuring of flashover voltage, is necessary insert the “High-voltage reference cable” between ignition cable and spark plug. At this „HV Reference cable“ then put „HV probe N“ (see figure below). Measurement of high voltage on one cylinder with a high voltage cables with „HV probe N“ and „HV Reference cable“ Ground High Voltage probe N High Voltage probe N High Voltage Reference cable High Voltage cable Technical parameters HV probe N - AT 111 4018 HV probe C1 - AT 111 4017 ±10% z MV ±15% z MV Measurements of the High Voltage reference cable AT 111 4056 High voltage Voltmeter in oscilloscope HV probe N - AT 111 4018 HV probe C1 - AT 111 4017 0 ... 25 kV 0,1 kV ±20% z MV ±30% z MV Measurement of the commonly used high-voltage cables MV: measured value Ground High Voltage probe N High Voltage probe N High Voltage cable Measurement of high voltage on one cylinder with a high voltage cables with „HV probe N“
Transcript of HV Probe NAT 111 4018 HV Reference cableAT 111 4056
Objednací číslo AT 505 5001
ATAL spol. s r.o. Lesní 47, Tábor - Horky, 390 01, Czech Republic Phone: +420 381 251 791, Fax: +420 381 253 043
e-mail: [email protected]; web: http://www.atal.cz
HHHVVV PPPrrrooobbbeee NNN ............................................................................................................AAATTT 111111111 444000111888 HHHVVV RRReeefffeeerrreeennnccceee cccaaabbbllleee.....................................................................AAATTT 111111111 444000555666
„HV probe N“ is used for measuring of the high voltage on the spark plugs by fitting the vehicle HV cable.
Option for Multi-Diag Scope
Multi-make Diagnostics Reference AT 111 4018, AT 111 4056
HV-probe-N-prospectus-en.doc The right is reserved to change this document (text and photos) ref.P111 0318
29.6
.201
1
During measuring on HV cables, when is required measuring of flashover voltage, is necessary insert the “High-voltage reference cable” between ignition cable and spark plug. At this „HV Reference cable“ then put „HV probe N“ (see figure below).
Measurement of high voltage on one cylinder with a high voltage cables with „HV probe N“
and „HV Reference cable“
Ground High Voltage probe N
High Voltage probe N
High Voltage Reference cable
High Voltage cable
Technical parameters HV probe N - AT 111 4018 HV probe C1 - AT 111 4017
±10% z MV ±15% z MV
Measurements of the High Voltage reference cable AT 111 4056
High voltage Voltmeter in oscilloscope
HV probe N - AT 111 4018 HV probe C1 - AT 111 4017
0 ... 25 kV 0,1 kV
±20% z MV ±30% z MV Measurement of the commonly used high-voltage cables
MV: measured value
Ground High Voltage probe N
High Voltage probe N
High Voltage cable
Measurement of high voltage on one cylinder with a high voltage cables with „HV probe N“
