HELIDECK FRICTION TEST - UK CAA, CAP 437 · 2018-10-17 · Approved Coating Applicators / Cert....
Transcript of HELIDECK FRICTION TEST - UK CAA, CAP 437 · 2018-10-17 · Approved Coating Applicators / Cert....
http://www.feds.solutions
HELIDECK FRICTION TEST - UK CAA, CAP 437
SL/HFT/C2 - v16.10.18
Services Rendered by:
“The landing area is a critical part of the helideck platform; keeping this safe for helicopter landingsis a key safety measure.”
Helideck Micro Grip Tester, recognized in UK CAA, CAP 437 is the world’s fi rst purpose built continuous friction measuring device designed specifi cally for testing Helidecks and Helicopter Landing Zones. Helideck MGT Testing it has been purpose built to cope with harsh offshore environments and for transportation too hard to reach facilities.
HELIDECK MICRO GRIP TESTER
Micro GripTester is the latest Helideck friction test equipment that meets all the strict requirements under UK CAA, CAP 437.
Helideck Friction Test carried out is based on UK CAA, CAP 437 which provides guidance on the periodicity of helideck friction testing. The helideck should be re-tested annually or when the condition of the deck suggests more frequent testing is appropriate.
FEDS ENGINEERING - HELITECH / CAP COMPLIANT SERVICES; a Member of British Helicopter Association (BHA); International Helideck Regulators Association (IHRA) and Helicopter Association International (HAI); specializes in Helideck Friction Testing on Offshore Installations and Vessels. With a team of trained Technicans, HFT is conducted using the latest friction measuring equipment. Our friction measuring devices and methodology meets all the strict requirements under UK CAA, CAP 437. Those of us involved in the offshore industry know more than most about the importance of safe working and risk management. With this in mind, regular helideck friction testing gives offshore installation operators the assurance needed to remove helideck landing nets. The fi rst assessment of a potential hazard, with the successful completion of a friction test, could be removed!
Member of:
Member of:
Member of:
MEET ALL UK CAA REQUIREMENTS!
Copyright FEDS ENGINEERING W.L.L. © 2015. All Rights Reserved.
BUILD IN COMPUTER & SOFTWARE The simple to use software installed on the Micro Grip Tester’s touch screen display guides the user through the friction test procedure with ease and stores the data straight onto the unit’s built in hard drive or directly onto a USB drive to allow for easy transfer of data.
OFFSHORE RIGS & PLATFORMS LP – HP Pipelines / Handrails / Platforms / Upgrades
ONSHORE RIGS & PLANTS Mud Tank Farm / New Build Accessories / Sub Racks
ON-SITE FABRICATION Carrying Out Fabrication Needs on Client’s Sites
SHIPYARDS & MARINE INDUSTRY Kort Nozzles / Jack Up Leg Repairs / MODU
INDUSTRIAL STEEL WORKS Welding / K-Nodes / Steel Replacement / Anodes
ENGINEERING REFURBISHMENT Pumps / Valves / Tanks / Vessels / Pipelines
SPECIALISED INSPECTIONS NDT / MPI / QA-QC / UT / IHRA
UNIQUE TECHNOLOGIES Tie Back Clean Out Tool / Sub Sea Positioning Equipment
STRUCTURAL ANALYSIS & DESIGN Platforms / Upgrade / Reinforce / ABS Steel
CONCEPTS DESIGN PROPOSAL Modifications / Upgrades / Innovations
EQUIPMENT & TOOLS DESIGN Custom Equipment / Custom Tools
CONSULTATION & MANAGEMENT Material & Process Selection / Project Management
HELIDECK CAP COMPLIANT SERVICES Friction Testing / Lighting System / Special Services
MATERIAL & EQUIPMENT SUPPLY Abrasives / HP – UHP Eqp. / JALITE Safety Signs
SURFACE PROTECTION & TREATMENT Surface Cleaning / Surface Preparation / Surface Protection
CERTIFIED EXPERTISE SUPPLY Approved Coating Applicators / Cert. SSPC, NACE, IRATA
Extract from UK CAA, CAP 437 Standardsfor Offshore Helicopter Landing Areas
3.37 The landing area should present a non-slip surface for helicopter operations. The installation operator should ensure that the helideck is kept free from oil, grease, ice, snow, excessive surface water or any other contaminant (particularly guano) that could degrade the surface friction. Assurance should be provided to the helicopter operator that procedures are in place for elimination and removal of contaminants prior to helicopter movements.
3.38 The minimum average surface friction values that should be achieved are detailed in Table 2. The average surface friction values should be confirmed using a test method acceptable to the CAA – see paragraphs 3.39, 3.40 and 3.41.
3.39 For flat helidecks with a micro-texture finish (e.g. non-slip paint or grit-blasted finish), the helideck friction test method should normally comprise the following:
a survey of the entire helideck surface in two orthogonal directions to a resolution of not less than 1 m2;
use of a tester employing the braked wheel technique and a tyre made of the same material as helicopter tyres;
testing in the wet condition using a tester that is capable of controlling the wetness of the deck during testing, and
use of a tester which provides electronic data collection, storage and processing.
HELIDECK RECOATING APPLICATION In case required parametres of surface friction are not achieved, FEDS ENGINEERING W.L.L. can carry out Helideck recoating including the application of a Anti-Slip aggregate so as to meet the UKCAA, CAP437 friction Standard.
http://www.feds.solutions
Section of helideck Fixed helideck Moving helideck
Inside TD/PM circle µ 0.60 µ 0.65
TD/PM circle and H painted markings µ 0.60 µ 0.65
Outside TD/PM circle µ 0.50 µ 0.50
Table 2: Friction requirements
FEDS / HELITECH RELATED SERVICES:HELIDECK LIGHT SYSTEM – UK CAA, CAP 437; CAP 1077HELIDECK SPECIAL SERVICES – UK CAA, CAP 437
http://www.feds.solutions
Powered by member of Group.
FEDS ENGINEERING W.L.L.Office 123-04, 1st FloorRegus Business CentreD-Ring Road, Al-Mataar Al-QadeemP.O. Box: 32522, Doha, Qatar
Tel: +974 4423 1142Fax: +974 4423 1100E-mail: [email protected]