HELICOPTER PLANETARY GEARBOX FAULT DETECTION · FAULT DETECTION Dr. Wenyi Wang Aerospace Division...
Transcript of HELICOPTER PLANETARY GEARBOX FAULT DETECTION · FAULT DETECTION Dr. Wenyi Wang Aerospace Division...
1
HELICOPTER PLANETARY GEARBOX FAULT DETECTION
Dr. Wenyi Wang
Aerospace Division
Defence Science and Technology Group (presented at ADF Propulsion Systems Symposium 2018)
UNCLASSIFIED
2
Helicopter Planetary Gearbox Fault Detection UNCLASSIFIED
• Background
• Detection Method
• Test Data
• Results
• Summary
Planet Bearing
Planet Gear Bore Crack
3
Background – 2009 accident of the Super Puma Helicopter
UNCLASSIFIED
AS-332L2 crash off Scottish coast (16 lives lost) – Caused by 2nd stage (upper) planet gear
fatigue failure (spall-induced) – One metal particle found (36 hours prior)
From Aviafora.com website
4
Background – 2016 accident of the Super Puma Helicopter
UNCLASSIFIED
H-225 crash off Norwegian coast (13 lives lost) – Again caused by 2nd stage (upper) planet gear
fatigue failure (spall-induced) – metal particles trapped by oil cooler
In both cases, on-board Vibration Health Monitoring (VHM) didn’t detect the fatigue cracks
Extremely challenging to detect such fault & its progression – a worldwide challenge From LN-OJF Final Repot_05 July 2018
Figure 31: The fracture surface divided into three different zones. The macro marks/features observed are indicated: solid line – well defined, dashed line – less well defined. Photo:
AIBN/QinetiQ
Det
ecta
ble?
5
Detection Method
UNCLASSIFIED
• Planetary rotation make detection very hard using fixed sensor
• Best candidate technique: US Patent US6298725-B1-2001: “Method for the
separation of epicyclic planet gear vibration signatures” by David Forrester of DST Group
Licensed to Honeywell (implementation ??) – certainly not in VHM system of Super Puma
Not mandatory for VHM
• Need to calculate Planet Gear Synchronous Signal Averaging
Web download: gear_fa_by_mcsoftware-d8bcjck.gif
6
Detection Method UNCLASSIFIED
• SSA with planet carrier is commonly employed in VHM • SSA with planet gear is less commonly employed (if at all ??) • Composite Planet-Gear Synchronous Signal Averaging (CP-SSA) is employed here • ‘Composite’ means SSA is the combined vibration from every planet gear, and
there is no separation of the vibration from the individual planet gears Reasoning : • Planet gear deformation caused by a bore crack would distort its mesh with the
ring and sun gears, and thus distort the planet gear mesh signature in the CP-SSA • The distortion would produce extra modulations to the normal gear mesh
signature, which should appear as modulation sidebands in the CP-SSA spectra
7
Detection Method
UNCLASSIFIED
Raw Vibration Signal
Composite Planet-SSA (CP-SSA)
remove the planet gear mesh harmonics
residual signal for the planet gear
RMS energy of the planet gear residual signal can be trended against time
In the envelope signal, we expect to observe double peaks when the defective section in the planet gear is in mesh with either the ring gear or the sun gear.
a squared envelope is then applied to the residual signal To further enhance the
diagnosis, we can obtain the CP-SSA over multiple revolutions of the planet gear.
8
Test Data UNCLASSIFIED
• A simple planetary gear test rig at University of New South Wales (UNSW) in Australia
• Torques on output shaft: 45 Nm, 65 Nm and 85 Nm • Speed of input shaft: 293 rpm fixed • 3 planet gears
• Two accelerometers and one tachometer • Sampling rate of 131072 Hz, 100 sec of data length
9
Results – Carrier-SSA & its spectrum
UNCLASSIFIED
• dominant spectral components are the planetary gear mesh harmonics indicated by multiples of 81 (ring gear tooth number)
• drive gear mesh harmonics by multiples of 55 (tooth number of the spur gear which meshes with the drive gear with 42 teeth)
0 160 320 480 640 800 960 1120 1280 1440
Carrier Shaft Order
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
Am
plitu
de (
G)
UNSW Planetary (Baseline 85Nm) SSR & SSA Spectra (Carrier)
Carrier-SSR: Resampled
Carrier-SSA: Averaged
X: 81
Y: 0.8075
X: 55
Y: 0.1108
X: 110
Y: 0.4087
X: 165
Y: 0.213
10
Results – CP-SSA
UNCLASSIFIED
• Could remove the two sets of dominant gear mesh harmonics at ×81 and ×55
• However, the removal of ×81 and ×55 harmonics from the carrier-SSA spectrum will still not be able to obtain the bore crack induced characteristics
• because the spectral content synchronous to planet gear rotation is averaged out in the Carrier-SSA
• This is why it is crucial to employ the SSA of the planet gears 0 30 60 90 120 150 180 210 240 270 300 330 360
Planet-gear Shaft Angle (deg)
-0.5
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
Am
plitu
de (
g)
UNSW Planetary Gear Baseline at 85Nm CP-SSA
Obviously, there are 23 spikes in the CP-SSA.
11
Results – residual signal from CP-SSA, healthy-state condition
UNCLASSIFIED
• removed the planet gear mesh harmonics at ×23 • a flat pattern (no peaks) with the planet gear residual signal across the whole revolution of the
planet gear. • However, the RMS under heavy load was increased slightly (from 0.0319 to 0.0353)
0 30 60 90 120 150 180 210 240 270 300 330 360
Planet-gear Shaft Angle (deg)
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
Am
plitu
de (g
)
UNSW Planetary Gear Baseline at 45Nm CP-SSA(1000) residual signal
0 30 60 90 120 150 180 210 240 270 300 330 360
Planet-gear Shaft Angle (deg)
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
Am
plitu
de (g
)
UNSW Planetary Gear Baseline at 85Nm CP-SSA(1000) residual signal
12
Results – residual signal from CP-SSA, 1-mm slot faulty-state
UNCLASSIFIED
• some obvious spikes in the residual signals at certain rotation angles of the planet gear, • there is a monotonic increase of RMS values with the increasing load.
0 30 60 90 120 150 180 210 240 270 300 330 360
Planet-gear Shaft Angle (deg)
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
Am
plitu
de (g
)
UNSW Planetary Gear Bore Slot 1.0mm at 45Nm: CP-SSA(1000) residual signal
0 30 60 90 120 150 180 210 240 270 300 330 360
Planet-gear Shaft Angle (deg)
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
Am
plitu
de (g
)
UNSW Planetary Gear Bore Slot 1.0mm at 65Nm: CP-SSA(1000) residual signal
0 30 60 90 120 150 180 210 240 270 300 330 360
Planet-gear Shaft Angle (deg)
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
Am
plitu
de (g
)
UNSW Planetary Gear Bore Slot 1.0mm at 85Nm: CP-SSA(1000) residual signal
45Nm torque where RMS = 0.0576
65Nm torque where RMS = 0.0614
85Nm torque where RMS = 0.067
13
Results – residual signal from CP-SSA, 1.5-mm slot faulty-state
UNCLASSIFIED
• Again, there is a monotonic increase of RMS values with the increasing load • the monotonic increase of the RMS values with the slot size • Under 65 & 85NM load, two abnormalities (double-peak) or fault features (separated by
roughly 180 degrees of shaft angle) are identifiable
45Nm torque where RMS = 0.0676
65Nm torque where RMS = 0.0767
85Nm torque where RMS = 0.0809
0 30 60 90 120 150 180 210 240 270 300 330 360
Planet-gear Shaft Angle (deg)
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
Am
plitu
de (g
)
UNSW Planetary Gear Bore Slot 1.5mm at 45Nm: CP-SSA(1000) residual signal
0 30 60 90 120 150 180 210 240 270 300 330 360
Planet-gear Shaft Angle (deg)
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
Am
plitu
de (g
)
UNSW Planetary Gear Bore Slot 1.5mm at 65Nm: CP-SSA(1000) residual signal
0 30 60 90 120 150 180 210 240 270 300 330 360
Planet-gear Shaft Angle (deg)
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
Am
plitu
de (g
)
UNSW Planetary Gear Bore Slot 1.5mm at 85Nm: CP-SSA(1000) residual signal
14
Results – Trending of RMS values of residual signals derived from CP-SSA
UNCLASSIFIED
• The EDM notch lengths of 1.0 mm and 1.5 mm into the rim of planet gear are equivalent to 28.57% (i.e. 1 / 3.5) and 42.86% (i.e. 1.5 / 3.5) of the gear rim being cracked from the bore
• The RMS value of the residual signal seems to be a good index for trending the crack length (severity) development
• Monotonic trend with both load the slot size
• planet gear bore cracking can be detectable using the residual signal of the CP-SSA
0 0.5 1 1.5
Length of Bore Slot (mm)
0.03
0.04
0.05
0.06
0.07
0.08
0.09
Am
plit
ude
SSA(1000) - yr RMS Values
45Nm
65Nm
85Nm
15
Results – for diagnosis (1 mm slot) CP-SSA over 3 revs
UNCLASSIFIED
• With the 1.0 mm notch, the features with planet-sun mesh appear to be quite weak and the in-between feature is stronger, for which we do not have an explanation
0 120 240 360 480 600 720 840 960 1080
Planet-gear Shaft Angle
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
Am
plitu
de
yr3 & ye3*5 for UNSW Planetary Gear Bore Slot: 1.0mm @45Nm
planet-ring mesh planet-sun mesh ??
0 120 240 360 480 600 720 840 960 1080
Planet-gear Shaft Angle
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
Am
plitu
de
yr3 & ye3*5 for UNSW Planetary Gear Bore Slot: 1.0mm @65Nm
0 120 240 360 480 600 720 840 960 1080
Planet-gear Shaft Angle
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
Am
plitu
de
yr3 & ye3*5 for UNSW Planetary Gear Bore Slot: 1.0mm @85Nm
45Nm torque – weak planet-sun mesh
65Nm torque – stronger planet-sun mesh
85Nm torque – stronger planet-sun mesh
16
Results – for diagnosis (1.5 mm slot) CP-SSA over 3 revs
UNCLASSIFIED
• With the 1.5 mm notch, there are two main features associated with the planet-ring mesh and planet-sun mesh (roughly 180 degrees apart), and other smaller features can be seen in between the two main features
0 120 240 360 480 600 720 840 960 1080
Planet-gear Shaft Angle
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
Am
plitu
de
yr3 & ye3*5 for UNSW Planetary Gear Bore Slot: 1.5mm @45Nm
0 60 120 180 240 300 360 420 480 540 600 660 720 780 840 900 960 1020 1080
Planet-gear Shaft Angle
-0.5
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
Am
plitu
de
yr3 & ye3*5 for UNSW Planetary Gear Bore Slot: 1.5mm @65Nm
0 60 120 180 240 300 360 420 480 540 600 660 720 780 840 900 960 1020 1080
Planet-gear Shaft Angle
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
Am
plitu
de
yr3 & ye3*5 for UNSW Planetary Gear Bore Slot: 1.5mm @85Nm
mesh with ring gear
mesh with sun gear
45Nm torque – strong planet-ring mesh
65Nm torque – stronger planet-ring mesh
85Nm torque – obvious planet-sun mesh
17
Results – explained UNCLASSIFIED
• A diagram showing the opening on tensile stress (red) and the closing on compressive stress (blue) of the bore crack of a planet gear in mesh with the ring and sun gears, respectively
• spikes due to the planet-ring and planet-sun gear meshes.
• This is because the planet gear with a bore crack is more deformed when the crack is aligned with radial load from gear mesh, i.e. the crack opens up in the tensile stress zone, than the planet gear without a bore crack.
• When the crack is not aligned with radial load of gear mesh, i.e. the crack closes down in the compressive stress zone, the deformation of the cracked gear is similar to the un-cracked gear
Ring Gear mesh load
Sun Gear mesh load
18
Summary
UNCLASSIFIED
• a technique to detect and diagnose a very challenging type of fault – planet gear bore cracking. • The fault detection can be achieved by trending the RMS values of the residual signal derived
from the composite planet-gear SSA (CP-SSA) signal. • When the RMS value exceeds a certain threshold, an anomaly of the planet gears is claimed to
be detected. • The diagnostic capability may be achievable using the squared envelope of the CP-SSA residual
signal over multiple revolutions of planet gear. • The meshing of the defective section in the planet gear with the ring and sun gears are
individually identifiable by the local spikes in the envelope of the residual signal, especially under high-load conditions.
• The technique has been validated using test data acquired from a small industrial planet gearbox test rig.
• Will be further validated by test data from a real helicopter gearbox
19
Summary – planned testing using Bell-208B main gearbox
UNCLASSIFIED
• A full-scale Bell-206B helicopter main rotor gearbox will be tested with a very fine EDM notch defect inserted into the rim of the planetary gear
• Try to initiate a real fatigue crack from the EDM notch and propagate it for a certain length with sufficient margin of safety to avoid catastrophic failure
• Multiple types of sensors used during this test, such as an in-line oil wear debris sensor, a wireless vibration sensor placed on the planet carrier inside the planetary gearbox, and traditional accelerometers externally placed on the gearbox housing
• The data from the various sensors will be fused to produce more convincing results
20
Question: Is this a unique problem for Super Puma? Answer: Not necessarily (but the solution can be unique for Super Puma)
UNCLASSIFIED
• If it would happen to any of the ADF Helicopters • we would be unable to detect it – safety & availability issue