H5350 Service Manual Acer Proyector

SERVICE MANUAL

SI : TSE: Check: Approved:

Date Revise Version Description

2008.01.24 V1.0 Initial Issue

H5350

Copyright Jan,2008. All Rights Reserved P/N: 36.89T03G001

H5350:95.87U20G019;95.87U20GC0E

Emy Roch

H5350 Confidential

Preface

This manual is applied to H5350 projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product.

Your customers will appreciate the quick response time when you immediately identify problems that occur with our products. We expect your customers will appreciate the service that you offer them.

This manual is for technicians and people who have an electronic background. Please send the product back to the distributor for repairing and do not attempt to do anything that is complex or is not mentioned in the troubleshooting.

Notice:

The information found in this manual is subject to change without prior notice. Any subsequent changes made to the data herein will be incorporated in future edition.

H5350 Service Manual

Copyright Jan.2008

All Rights Reserved

Manual Version 1.0

H5350 Confidential

Table of Content

Chapter 1 Introduction Highlight 1-1

Compatible Mode 1-3

Product Overview 1-7

Chapter 2 Disassembly Process Equipment Needed & Product Overview 2-1

Disassemble Lamp Cover Module 2-2

Disassemble Lamp Module 2-2

Disassemble Top Cover Module 2-3

Disassemble Top Shielding 2-4

Disassemble Main Board Module & I/O Cover Module 2-4

Disassemble Front Cover Module 2-6

Disassemble Engine Module 2-7

Disassemble Color Wheel Module 2-8

Disassemble Zoom Ring & Focus Ring 2-9

Disassemble DMD Board and DMD Chip Module 2-10

Disassemble Fan Module 2-11

Disassemble Blower Module 2-12

Disassemble Speaker Module 2-13

Disassemble LVPS Module 2-14

Disassemble Interrupt Switch Module 2-15

Disassemble Lamp Driver Module 2-16

Disassemble Bottom Cover Module 2-18

Rod Adjustment 2-19

Re-write Lamp Usage Hour 2-20

H5350 Confidential

Assemble Bottom Cover Module 2-21

Assemble Lamp Driver Module 2-22

Assemble Interrupt Switch Module 2-24

Assemble LVPS Module 2-25

Assemble Speaker Module 2-26

Assemble Blower Module 2-26

Assemble Fan Modul 2-27

Assemble DMD Board and DMD Chip 2-28

Assemble Zoom Ring&Focus Ring 2-29

Assemble Color Wheel Module 2-30

Assemble Engine Module 2-31

Assemble Front Cover Module 2-32

Assemble Main Board Module & I/O Cover Module 2-33

Assemble Top Shielding 2-34

Assemble Top Cover Module 2-35

Assemble Lamp Module 2-36

Assemble Lamp Cover Module 2-36

Chapter 3 Troubleshooting

LED Lighting Message 3-1 Main Procedure 3-2

Chapter 4 Function Test & Alignment Procedure

Test Equipment Needed 4-1

Service Mode 4-1

OSD Reset 4-1

Test Condition 4-2

Test Inspection Procedure 4-3

H5350 Confidential

PC Mode 4-3

Defectspecificationtable 4-7

Video Performance 4-7

Optical Performance Measure 4-9

Other 4-10

Chapter 5 Firmware Upgrade Equipment Needed 5-1

DLP Composer Lite Setup Procedure 5-2

USB Driver Upgrade Procedure 5-4

Firmware Upgrade Procedure 5-5

Chapter 6 EDID Upgrade EDID Introduction 6-1

Equipment Needed 6-2

Setup Procedure (VGA) 6-3

EDID Key-In Procedure 6-4

Setup Procedure (HDMI) 6-6

Appendix A Exploded Image I

Appendix B SerialNumberSystemDefinition XXI PCBACodeDefinition XXII

H5350 Confidential 1-1

Chapter 1

Introduction

1-1 Highlight

No Item Description1 Dimensions (WxHxD) - 267 mm X 187 mm X 80 mm 2 Weight - <5 lbs 3 Tilt Angle - 4 degree with elevator mechanism

4 Power Supply

- Universal AC 100 – 240 V ~ 50-60 Hz with PFC input - 180W for Osram E20.6 Lamp @ normal operation- Variant FAN speed control (Depends on temperature vari ance)

5 Keystone correction - +/ -40 degree (80 degree)

6 Cooling system

- Advanced Air Flow- Two fans with system acoustic noise level 35 dB(A) (typi cal)- Temperature control circuits with adaptive fan rotational speeds- Maximum touch temperature follow UL60950-1

7 Brightness -1700 ANSI Lumens (Typical; Full power mode)-1450 ANSI Lumens (Minimum; Full power mode)

8 Contrast- 1500 : 1 Full White and Black (Minimum; Full power mode)- 1800 : 1 Full White and Black (Typical; Full power mode)

9 Uniformity- 65% Japan standard (Minimum; Full power mode)- 80% Japan standard (Typical; Full power mode)

10 Throw ratio - 58”@2M(1.55 ~ 1.70 :1)11 Audio - 2W*1

12 Projection lens- F# 2.44~2.58, f = 21.83~23.81 mm, 1.10X Mechanical Zoom Lens

13 Lamp life - 3500 hours min, 50% survival rate14 System controller - TI DDP2230


No Item Description

15 Terminal

- One HDMI input- One D-sub VGA input - One RCA Composite input- Three RCA Component input- One S-Video input(4 pin Mini din)- One audio input (2.5m phone jack)- One USB port (Type B Female)

16 Lamp housing

- Lamp Assembly could be changed by customer himself, but should read the user manual for instruction in advance.- Lamp Assembly should be provided by Coretronic and dis tributed through authorized agencies.

17 Input signal spec.

- Hsync Frequency 31 ~ 100 kHz- Vsync Frequency 56 ~ 85 Hz- Video Signal RGB (PC)● Analog RGB 0.7Vp-p, 75 ohm, Separate TTL H,V Sync● Analog RGB 1Vp-p, 75 ohm, Sync. On Green signal● Analog RGB 0.7Vp-p, 75 ohm, Composite TTL Sync.- Video● Composite video 1Vp-p,75 ohm● S-video Luminance 0.714Vp-p, 75 ohm● Chrominance 0.286Vp-p, 75 ohm● Component Video 1Vp-p, 75 ohm

18 TI DMD- TI DMD 0.62” 12° 2xLVDS Type-A 720p Digital Mirror Device

19 Video compatibility

- Standards :● NTSC (3.58/4.43)● PAL (B/D/G/H/I/M/N)● SECAM (B/D/G/K/K1/L)● HDTV - 480i,576i 480p, 576p, 720p, 1080i,1080p

20 XGA / Compression- Compression : by using “DDP2230” Chips can make image compression

21 Number of active dots - 1280(H) x 720(V)

22 Color wheel- 6 segments (R90/Y35/G90/C35/W28/B82)- 7200 rpm

23 Lamp- 180 – Watt OSRAM Lamp (user replaceable) for full power mode

24 Temperature- Operating: 5°C -- 35°C- Storage: -20°C -- 60°C


1-2 Compatible Mode

Computer Compatibility (Analog)A. VGA Analog(1) VGA Analog - PC Signal

Modes Resolution V.Frequency[Hz]

H.Frequency[KHz]

VGA

640x480 60 31.5640x480 72 37.9640x480 75 37.5640x480 85 43.3720x400 70 31.5720x400 85 37.9

SVGA

800x600 56 35.2800x600 60 37.9800x600 72 48.1800x600 75 46.9800x600 85 53.7832x624 75 49.725

XGA

1024x768 60 48.41024x768 70 56.51024x768 75 601024x768 85 68.7

SXGA

1152x864 70 63.81152x864 75 67.51152x864 85 77.1

1280x1024 60 63.981280x1024 72 76.971280x1024 75 79.981280x1024 85 91.1

QuadVGA1280x960 60 59.71280x960 75 75.23

SXGA+ 1400x1050 60 63.98UXGA 1600x1200 60 75

Power Mac G4 640x480 66.6(67) 34.93Power Mac G4 800x600 60 37.9Power Mac G4 1024x768 60 48.4Power Mac G4 1152x870 75 68.68Power Mac G4 1280x960 75 75PowerBook G4 640x480 60 31.35PowerBook G4 640x480 66.6(67) 34.93PowerBook G4 800x600 60 37.9PowerBook G4 1024x768 60 48.4



H.Frequency[KHz]

PowerBook G4 1152x870 75 68.68PowerBook G4 1280x960 75 75i Mac DV(G3) 1024x768 75 60

(2) VGA Analog - Extended Wide timing

WXGA1280x768 60 48.361280x768 75 57.61280x768 85 68.63

Native

1280x720 60 451280x800 60 49.7021440x900 60 55.935

1680x1050 60 65.3


B. HDMI Digital (1) HDMI – PC Signal


H.Frequency[KHz]

VGA

640x480 60 31.5640x480 72 37.9640x480 75 37.5640x480 85 43.3720x400 70 31.5720x400 85 37.9

SVGA

800x600 56 35.1800x600 60 37.9800x600 72 48.1800x600 75 46.9800x600 85 53.7832x624 75 49.7

XGA

1024x768 60 48.41024x768 70 56.51024x768 75 601024x768 85 68.7

SXGA

1152x864 70 63.81152x864 75 67.51152x864 85 77.1

1280x1024 60 641280x1024 72 771280x1024 75 801280x1024 85 91.1

QuadVGA1280x960 60 601280x960 75 75.2

SXGA+ 1400x1050 60 65.3UXGA 1600x1200 60 75

Power Mac G4 640x480 66.6(67) 34.9Power Mac G4 800x600 60 37.9Power Mac G4 1024x768 60 48.4Power Mac G4 1152x870 75 68.7Power Mac G4 1280x960 75 75PowerBook G4 640x480 60 31.4


Modes Resolution V.Frequency[Hz] H.Frequency [KHz]

PowerBook G4 640x480 66.6(67) 34.9PowerBook G4 800x600 60 37.9PowerBook G4 1024x768 60 48.4PowerBook G4 1152x870 75 68.7PowerBook G4 1280x960 75 75i Mac DV(G3) 1024x768 75 60

(2) HDMI – Extended Wide timing

WXGA1280x768 60 47.81280x768 75 60.31280x768 85 68.6

(Native)

1280x720 60 44.81280x800 60 49.61440x900 60 59.9

1680x1050 60 65.3(3) HDMI – Video SignalFor TWN/USA SKU

480i (NTSC) 720x480(1440x480) 59.94(29.97) 15.7480p (NTSC) 720x480 59.94 31.5720p (NTSC) 1280x720 60 451080i (NTSC) 1920x1080 60(30) 33.71080p (NTSC) 1920x1080 60 67.4

For EMEA SKU576i (PAL) 720x576(1440x576) 50(25) 15.6576p (PAL) 720x576 50 31.3720p (PAL) 1280x720 50 37.51080i (PAL) 1920x1080 50 28.11080p (PAL) 1920x1080 50 56.3

Graphic source monitor range limits

Horizontal scan rate: 31k-100kHzVertical scan rate: 56-85Hz


Product Overview

Projector Outlook

Front /Upper side

Item Description Item Description1 Zoom ring 5 Power button and Power Indicator LED2 Focus ring 6 Remote control3 Zoom lens 7 Remote control receiver4 Lens cap


Rear side

Item Description Item Description1 USB connector 6 Composite video input connector2 HDMI connector 7 Audio input connector

3 Analog RGB/component inputconnector 8 Power socket

4 Component video input connector 9 KensingtonTM lock port5 S-Video input connector


Remote Control and Control Panel Layout


Item Icon Function Description

1 Infraredtransmitter Sends signals to the projector.

2 Power/PowerLED Power button and Power Indicator LED.

3 POWER Refer to the “Turning the Projector On/Off” section.

4 MENU

• Press “MENU” to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu.• Confirm your selection of items.

5 Four directionalselect keys

Use up, down, left, right buttons to select items or makeadjustments to your selection.

6 ZOOM Zooms the projector display in or out.7 ASPECT RATIO To choose the desired aspect ratio (Auto/4:3/16:9/L.Box).8 KeyPad 0~9 Press “0~9” to input a password in the “Security settings”.

9 KEYSTONE Adjusts the image to compensate for distortion caused bytilting the projector (± 40 degrees).

10 RESYNC Automatically synchronizes the projector to the input source.

11 SOURCE Press “SOURCE” to choose RGB, Component, S-Video,Composite and HDTV sources.

12 HIDE Momentarily turns off the video. Press “HIDE” to hide theimage, press again to display the image.

13 Empoweringkey Unique Acer functions: eView, eTimer Management.

14 FREEZE To pause the screen image.

Note:


Remote Control Placement

Please refer to the illustration to attach the remote control to the projector.


Connecting the Projector

Item Description Item Description1 Power cord 6 HDMI cable2 USB cable 7 RCA component cable for YPbPr3 VGA cable 8 S-Video cable4 Composite video cable 9 Audio cable Jack/RCA5 Audio cable Jack/Jack

Note: To ensure the projector works well with your computer,please make sure the

timing of the display mode is compatible with the projector.


Bottom Cover Dimension

H5350 Confidential 2-�

Chapter 2

Disassembly& Assembly Process2-1 Equipment Needed & Product Overview

1. Screw Bit (+) :107

2. Hex Sleeves 5mm

3. Screw Bit (+) :102

4. Screw Bit (-) :102

5. Long Nose Nipper

6. Tweezers

7. H5350 unit

* Before you start: This process is protective level II. Operators should wear electrostatic chains.

* Note: If you need to replace the main board, you have to get into service mode and record the

lamp usage hour. please refer to section 2-20.


2-3 Disassemble Lamp Module

1. Unscrew 2 screws on Lamp Module

2. Disassemble Lamp Module

2-2 Disassemble Lamp Cover Module

1. Unscrew 2 screws on Lamp Cover Module

2. Disassemble Lamp Cover Module

Lamp Module

Lamp Cover Module


2-4 Disassemble Top Cover Module

1. Unscrew 2 screws on the unit base

2. Disassemble Top Cover Module(As the

picture show)

Note: - You should drop out

of three tenons first, and then push

the Top Cover Module to back.

Top Cover Module


2-5 Disassemble Top Shielding

1. Unscrew 7 screws on Top Shielding

2. Disassemble Top Shielding

2-6 Disassemble Main Board Module & I/O Cover Module

1. Unscrew 2 hex screws

2. Tear a tape

3. Unscrew 1 screw and 6 connectors on

Main Board Module

Top Shielding


4. Pull up the Main Board Module and then

unplug 1 connector(As green square)

5. Disassemble Main Board Module and I/O

Cover Module6. Unscrew 3 screws to disassemble I/O

Cover Module from Main Board Module

I/O Cover Module Main Board Module


2-7 Disassemble Front Cover Module

1. Unscrew 1 screw(As yellow circle)

2. Press 1 tenon on each side and then pull

up the Front Cover Module

3. Disassemble Front Cover Module

Front Cover Module


2-8 Disassemble Engine Module

1. Pull the higher-part of Mylar up(As the

red square)

2. Unscrew 4 screws on Engine Module

3. Disassemble Engine Module

Engine Module


2-9 Disassemble Color Wheel Module

1. Unscrew 2 screws to disassemble Color

Wheel Module

2. Unscrew 1 screw to disassemble Photo

Sensor Board from Color Wheel Module

Color Wheel Module

Photo Sensor Board


2-10 Disassemble Zoom Ring & Focus Ring

1. Unscrew 2 screws on Engine Module to

disassemble the Zoom Ring and Zoom

Ring Holder

2. Unscrew 3 screws to disassemble Focus

Ring

Focus Ring

Zoom Ring Holder and Zoom Ring

H5350 Confidential 2-�0

2-11 Disassemble DMD Board and DMD Chip

1. Unscrew 4 screws on Engine Module to

disassemble Heat Sink

2. Unscrew 4 hex screws to disassemble

DMD Board and DMD Chip

Heat Sink

H5350 Confidential 2-��

2-12 Disassemble Fan Module

1. Unscrew 4 screws

2. Take the Fan Cable out of the aperture

(As the red square)


2-13 Disassemble Blower Module

1. Unscrew 3 screws to disassemble Blower

Module

2. Disassemble Rubber from the Blower

3. Unscrew 4 screws to disassemble Fan

Module

4. Unscrew 1 screw to disassemble Thermal

Switch


2-14 Disassemble Speaker Module

1. Unscrew 1 screw and press 2 tenons to

disassemble Speaker Module

Note: - Use the tweezers to press the tenon.

2. Press the two tenons outward to

disassemble the Speaker from the

Speaker Holder


2-15 Disassemble LVPS Module

1. Unscrew 1 ground screw(As red circle)

2. Unscrew 1 screw on LVPS Module(As

yellow circle) to disassemble LVPS BRKT

3. Unscrew 3 screws on LVPS Module(As

green circle)

4. Unplug 2 connectors to disassemble

LVPS ModuleLVPS BRKT

LVPS Module


2-16 Disassemble Interrupt Switch Module

1. Unscrew 1 screw and disassemble 1 Film

Tape to disassemble Interrupt Switch

Module

2. Tear off a Mylar

3. Press 2 tenons to disassemble Interrupt

Switch from Interrupt Switch Holder

Interrupt Switch Module

Film tape

Aperture

Dent


2-17 Disassemble Lamp Driver Module

1. Unscrew 1 screw to disassemble Lamp

Driver Module

2. Unplug 1 connector(As red square) and

unscrew 2 screws (As green circle) to

disassemble Lamp Driver to Lamp Cable

3. Disassemble 1 Mylar(As green square)

Lamp Driver to Lamp Cable


4. Unplug 2 connectors to disassemble 2PIN

and 5PIN cable

5. Unscrew 4 screws to disassemble Lamp

Driver from Lamp Driver Holder

2 PIN&5 PIN Cable

Lamp Driver HolderLamp Driver Module


2-18 Disassemble Bottom Cover Module

1. Unscrew 1 screw on Bottom Cover

Module

2. Tear 1 EMI tape

3. Disassemble the Bottom Cover Shielding

from Bottom Cover Module

�. Pull aside the iron sheet with Tweezers

to disassemble the ROD DUCT from

Bottom Cover Module

Note: - Due to the iron sheet is out of shape

easily,so we must turn it back before

assemble the ROD DUCT.

5. The disassembly is completed

Bottom Cover ModuleBottom Cover Module Shielding

ROD DUCT


2-19 Rod Adjustment

1. Environment adjustment

- The distance between the engine and the

screen is 2.25 M

- This process should be done at a dark

environment. (under 5 Lux)

2. Procedure adjustment

- Change the screen to “white screen.”

- Adjust the screws by using the rod on

the engine module to readjust the image.

(adjust until the yellowish or bluish parts

disappeared.)

3. Abnormal image inspection

- It should not have any abnormal color at

the rim of the image by estimating through

the eyes.

Note: - To avoid over adjust the rod.

- “Screw 1” should be adjusted first, and

then adjust the “Screw2”.After the

adjustment, use the glue to fix the

screws.

1

2


2-20 Re-write Lamp Usage Hour

1. Get into service mode.

- press (power > left > left > menu) to get

into service mode.

- Click “RD Test” to get into the next step

2. Select “Lamp life” and use left or right key

to re-write the lamp hour back to previous

lamp usage hour.

3. Choose “Return to Service Menu” and

then exit the service mode

Note: left key = decrease lamp hour

right key =increase lamp hour

Check the lamp usage hour

Re-write lamp usage hour

H5350 Confidential 2-2�

2-21 Assemble Bottom Cover Module

1. Assemble ROD DUCT on the Iron Sheet

2. Assemble the Bottom Cover Shielding on

Bottom Cover Module

3. Stick 1 EMI tape

4. Screw 1 screw on Bottom Cover Module

Bottom Cover ModuleBottom Cover shielding


2-22 Assemble Lamp Driver Module1. Screw 4 screws to assemble Lamp

Driver Module on Lamp Driver Holder

2. Plug 2 connectors to assemble 2PIN and

5PIN cable

Note: - The 2 PIN and 5 PIN cable must be pass

through a Dent.(As the yellow square)

3. Stick a Mylar

2 PIN&5 PIN Cable

Lamp Driver HolderLamp Driver Module

Lamp Driver to Lamp Cable


4. Plug 1 connector(As blue square)and

screw 2 screws to assemble Lamp Driver

to Lamp Cable

Note: - The lamp driver to lamp cable must be

passed through two Dents.(As the yellow

square)

5. Screw 1 screw on Lamp Driver Module


Interrupt Switch Module

2-23 Assemble Interrupt Switch Module

1. Fasten 2 tenons to assemble Interrupt

Switch on Interrupt Switch Holder

2. Stick a Mylar on Interrupt Switch Module

3. Screw 1 screw and stick 1 film tape to

assemble Interrupt Switch Module

Note: - Interrupt Switch cable must be passed

through a dent and a aperture.And use

a film tape to fix the cable in the dent.

Film tape

Aperture

Dent


2-24 Assemble LVPS Module

1. Plug 2 connectors (As yellow square)

and screw 3 screws (As green circle) to

assemble LVPS module

2. Screw 1 screw to assemble LVPS BRKT

(As yellow circle)

3. Screw 1 ground screw(As red circle)

LVPS BRKT LVPS Module


2-25 Assemble Speaker Module

1. Fasten 2 tenons to assemble the

speaker on the speaker holder

2. Fasten 2 tenons and screw 1 screw to

assemble Speaker Module

.

2-26 Assemble Blower Module

1. Assemble the Rubber on the Blower

2. Screw 3 screws to assemble Blower

Module


2-27 Assemble Fan Module

1. Screw 1 screw to assemble

Thermal Switch(As green circle)

2. Screw 4 screws to assemble Fan Module

3. Screw 4 screws to assemble Fan Module

on the unit

Note: - The fan cable pass through from the

aperture.


2-28 Assemble DMD Board and DMD Chip1. Screw 4 hex screws to assemble all

components of DMD parts

2. Screw 4 screws on Engine Module to

assemble Heat Sink


2-29 Assemble Zoom Ring&Focus Ring

1. Screw 3 screws to assemble Focus Ring

2. Screw 2 screws on Engine module to

assemble Zoom Ring and Zoom Ring

Holder

Zoom Ring Holder and Zoom Ring


2-30 Assemble Color Wheel Module

1. Screw 1 screw to assemble Photo

Sensor on Color Wheel Module

2. Screw 2 screws to assemble Color

Wheel Module


2-31 Assemble Engine Module

1. Push the higher-part of Mylar down(As the

red square) to assemble Engine Module

2. Screw 4 screws to assemble Color Wheel

Module


2-32 Assemble Front Cover Module

1. Push down the Front Cover Module

2. Fasten 1 tenon on each side

3. Screw 1 screw(As yellow circle) to

assemble Front Cover Module


2-33 Assemble Main Board Module & I/O Cover Module

1. Screw 3 screws to assemble I/O

Cover Module on Main Board Module

2. Plug 1 connector(As green square)

3. Screw 1 screw and 6 connectors on

Main Board Module

4. Stick a tape

I/O Cover Module Main Board Module


5. Screw 2 hex screws

2-34 Assemble Top Shielding

1. Screw 7 screws on the Top Shielding


2-35 Assemble Top Cover Module

1. Fasten 3 tenons to assemble Top

Cover Module on the unit

Note: - You should press three tenons first,

and then push the Top Cover Module

to back.

2. Screw 2 screws on the unit base


2-36 Assemble Lamp Module

1. Assemble Lamp Module

2. Screw 2 screws on Lamp Module

2-37 Assemble Lamp Cover Module

1. Assemble Lamp Cover Module

2. Screw 2 screws on Lamp Cover Module

3. Assembly is completed

Lamp Cover Module


Chapter 3

Troubleshooting3-1 LED Lighting Message

MessagePower LED

Red Blue

Input Power Plug Flash ON to OFF 100ms --

Standby V --

Power button ON -- V

Lamp retry -- Quick Flashing

Power off (Cooling state) Quick Flashing --

Power button OFF:Cooling completed;

Standby ModeV --

Error (Thermal Failure) Quick Flashing RED and Steady BLUE by returns

Error (Fan lock) Quick Flashing RED and Steady BLUE by returns

Error (Lamp break-down) Quick Flashing BLUE and Steady RED by returns

Error (Color Wheel fail) Quick Flashing BLUE and Steady RED by returns


3-2 Main Procedure

No Symptom Procedure

� No Power

- Ensure the Power Cord and AC Power Outlet are securely connected

- Check Lamp Cover and Interrupt Switch

- Ensure all connectors are securely connected and aren’t

broken

- Check Lamp Driver

- Check LVPS

- Check Main Board

� Auto Shut Down

- Check LED Status

a. Lamp LED Light

- Check Lamp

- Check Lamp Driver

- Check Main Board

b. Temp LED Light

- Check Thermal Switch

- Check Fan

c. Color Wheel

- Check Color Wheel

- Check Photo Sensor



3 No Image

- Ensure the Signal Cable and Source work

(If you connect multiple sources at the same time, use the “Source” button switch)

- Ensure all connectors are securely connected and aren’t

broken

- Check Main Board

- Check DMD Board

- Check DMD Chip

- Check Engine Module

4 No Light On

- Ensure all connectors are securely connected and aren’t broken

- Check Lamp Module

- Check Lamp Driver

- Check LVPS

- Check Main Board

5 Machanical Noise- Check Color Wheel

- Check Fan Module

6 Line Bar/Line Defect

- Check if the Main Board and the DMD Board are

assembled properly

- Check Main Board

- Check DMD Board

- Check DMD Chip

7 Image Flicker

- Do “Reset(All data)” of the OSD Menu

- Ensure that the signal cables and source are work as well

- Check Lamp Module

- Check Color Wheel

- Check DMD Board

- Check Main Board



8 Color Abnormal


- Adjust Color Wheel Index

- Check Main Board

- Check Color Wheel

9 Poor Uniformity/Shadow

- Ensure the projection screen without dirt

- Ensure the projection lens is clean

- Ensure the Brightness is within spec

- Check rod alignment


�0 Dead Pixel/Dust(Out of spec.)

- Ensure the projection screen without dirt

- Ensure the projection lens is clean

- Clean DMD Chip and Engine Module

- Check DMD Chip


�� Garbage Image

- Ensure that the signal cables and source work as well

- Check Main Board

- Check DMD Board

�� Remote Control

- Remote Control

a.Check Battery

b.Check Remote Controller

c.Check Main Board

�3 Function Abnormal


- Check Main Board

- Check DMD Board

�4 Audio Abnonrmal

- Ensure that the signal cables and source are work as well

- Check Speaker Module

- Check Main Board



�5Forgetting Password (adminstrator Password)

- An unique Universal Password which is printed on the Security Card. This unique password is a back door of Administrator Password which will be accepted by projector anytime no matter what the Administrator Password is.

- How to get the Universal Password? (1) Click the “AcerSNID”

(2) Input SNID number.(SNID number is on the Security Card)

(3) Click“Calculate”.Then the Universal Password will appear.


Chapter 4

Function Test & Alignment Procedure

4-1 Test Equipment Needed

- IBM PC with XGA resolution and Wireless Network Card

- DVD player with Multi-system (NTSC/PAL/SECAM), equipped “Component”, “S-Video”

, “Composite” and "HDMI".

- HDTV Source (480P, 720P, 1080i)

- Minolta CL-100

- Quantum Data 802B or CHROMA2327 (Color Video Signal & Pattern Generator)

- After changing parts, check the information below.

4-2 Service Mode

1. Turn on the projector and input the signal

2. Do the following actions sequentially to enter service mode menu

(1) Press "Power→Left→Left→Menu".

(2) Service mode will be shown.

(3) After confirming the configuration, press "Exit" to exit.

4-3 OSD Reset

1. After final QC step, we have to erase all saved change again and restore the OSD default setting. The following actions will allow you to erase all end-users' settings and restore the default setting:

(1) Please enter OSD menu.

(2) To execute "Reset" function.


4-4 Test Condition

- Circumstance brightness: Dark room less than 5.0 lux.

- Inspection distance: 1.8m~2.5m functional inspection.

- Screen size: 60 inches diagonal

- After repairing each H5350, the unit should be run-in (refer to the table below)

Symptom Run-in TimeNormal repair 2 hoursNFF 4 hoursAuto shut down 6 hours

- Enter Burn-In Mode* Cycle setting is based on the defect symptoms. ie: If it is NFF, the run-in time is 4 hours. You have

to set the lamp on for 50 min. and lamp off for 10 min for 4 cycles.

Press power > left > left > MenuChoose Burn-In Test > enterLamp On (Min) Press right key to adjust the time (50)Lamp Off (Min) Press right key to adjust the time (10)Set burn in cycle Press right key to adjust the cycleAfter setting up the time, choose Burn-In mode and hit enter

Screen Defects (While replacing DMD Chip, DMD BD and MB)

< Figure: Zone A &B Definition >


4-5 Test Inspection Procedure

Charge parts/ Update M/B FW Color Wheel Lamp Module

Version Update v vColor Wheel Index v v

PC Calibration

YPbPr Calibration

Reset lamp hour vOSD Reset v v

EDID vRe-write Lamp

Hour Usage v

4-6 PC MODE

1. Frequency and tracking boundry

Procedure - Test equipment: video generator. - Test signal: analog 1280 x 720@60Hz - Test Pattern: general-1 or master - Check and see if the image sharpness is well-

performed. - If not re-adjust by the following steps: (1) Select "Frequency" function to adjust the

total pixel number of pixel clock in one line period.

(2) Select "Tracking" function and use right or left arrow key to adjust the value to minimize

General-1

Master


video flicker. - Adjust Resync or Frequency/Tracking/H. Posi-

tion/V. Position to the inner screen.Inspection item - Eliminate visul wavy noise by Rsync, Frequency

or Tracking selction. - Check if there is noise on the screen. - Horizontal and vertical position of the vedio

should be adjustable to the screen frame.Criteria - If there is noise on the screen, the product is

considered as faliure product. - If there is noise on the screen, use auto or

manual “frequency” function or “tracking” func-tion to adjust the screen.

- The PC mode functionally sure be workable include support format with frequency and auto detected functional will be workable.

2. Light Leak

Procedure - Test equipment: video generator. - Test signal: analog 1280 x 720@60Hz1280 x 720@60Hz - Test Pattern: gray 30 patterns - Check if the light leaks. * Light leak on reflective edge, eyecatcher, bond-

wires and exposed metal.Inspection item - Light leak check. - Bright blemish (dirty).Criteria - The pattern cannot accept the color level of the

leakage is brighter than the gray 30 pattern. - Ref. below table Note: The defect criteria follows TI specification.

3. Blemish (Dark)

Procedure - Test equipment: video generator. - Test signal: analog 1280 x [email protected] x 720@60Hz.. - Test Pattern: blue 60

Gray 30

Blue 60


Inspection item - Dark blemish check.(dirty)Criteria - The bright blemish is unacceptable when it ap-

pears on blue 60 pattern. - Ref. below table Note: The defect criteria follows TI specification.

4. Dead Pixel (Bright pixel)

Procedure - Test equipment: video generator. - Test signal: analog 1280 x [email protected] x 720@60Hz.. - Test Pattern: full blackInspection item - Bright pixel check. Note: Frame dimension under operative zone1

inchCriteria - Bright pixel is unacceptable. - Ref. below table Note: The defect criteria follows TI specification.

5. Dead Pixel (Dark pixel)

Procedure - Test equipment: video generator. - Test signal: analog 1280 x [email protected] x 720@60Hz.. - Test Pattern: full whiteInspection item - Dead pixels check. - White pattern (IRE=100) - Adjacent dark pixel.Criteria - The number of the dead pixels should be less or

equal to 6 pixels. - Adjacent pixel with each other is unacceptable. - Ref. below table Note: The defect criteria follows TI specification.

6. Focus test

Procedure - Test equipment: video generator. - Test signal: analog 1280 x 720@60Hz1280 x 720@60Hz

Full black

Full white


- Test Pattern: full screen or MEME Sony Inspection item - Focus check

Criteria - From screen 2.25 M via visual to check the focus, look at the entire screen, focus shall be clear, crisp, and sharp over the entire surface of the display pattern.(Blur word on one of the corner after adjustment is acceptable. However, the word should at least be recognizable.)

7. Color performance

Procedure - Test equipment: video generator. - Test signal: HDMI 720p,1080i - Test Pattern: Master, In focus II or SMPTE RP-

�33 * Please refer to 4-2 to enter service mode.

Use 720P & 1080i signal, master pattern to do HDTV test. Color cannot discolor to purple and blue. If the test result is discoloration or flicker-ing, please return the unit back to repair

centers.Inspection item - Check if each color level is well-functioned. - color saturations

Criteria - Screen appears normal. It should not have any abnormal condition, such as lines appear on the screen and so on.

- Color appears normal. - It is acceptable to have few lines flashing at the

center and on the edge of 1080i image. How-ever, rest of the image should appears stable.

- RGBW should all appear normal on the screen and sort from R -G-B-W.

- Color levels should be sufficient and normal. (the unidentified color levels on both left and right sides should not over 8 color levels.)

- Grey level should not have abnormal color or SMPTE RP-133

InFocus II / 64 gray RGBW

Master

MEME Sony

Full screen


heavy lines. - The PC mode functionally sure be workable

include support format with frequency and auto detected functional will be workable

4-7 Defect specification table

Order Symptom Pattern Criteria

� Bright pixel ( dots) Black pattern

( IRE=O)A+B=0

2 Dark pixel(dots) White patternA+B=6

3 Unstable pixel (dots) Any pattern A+B=1

4 Adjacent dark pixel (dots) Any pattern

A+B=0

5 Dark blemish (Dirty) Blue 60 patternA+B=3

(diameter <1/2 inch)

6 Bright blemish (Dirty) Gary 30 patternA+B=3

(diameter <1/2 inch)

7 Bright dot on frame Black pattern 2

4-8 Video Performance

1. CVBS

Procedure - Test equipment: DVD player - Test signal: CVBS

Motion video


Inspection item - Video performance testInspection Distance - 1.8M ~2.5M Criteria - Check any abnormal color, line distortion or anyabnormal color, line distortion or any color, line distortion or any

noise on the screen. - Check the sound from speakers.

2. S-VideoProcedure - Test equipment: DVD player - Test signal: S-Video

Inspection item - Video performance testInspection Distance - 1.8M ~2.5M Criteria - Check any abnormal color, line distortion or any


3. HDTV/ Component

Procedure - Test equipment: DVD player - Test signal: Ycbcr/YPbPr Inspection item - HDTV performance testInspection Distance - 1.8M ~2.5MCriteria - Check any abnormal color, line distortion or anyabnormal color, line distortion or any color, line distortion or any


4. Audio Test

Procedure - Test equipment: DVD player - Test signal: CVBS Inspection item - Audio performance testInspection Distance - 1.8M ~2.5MCriteria - Check the sound from speakers. - Check “Volume” is normal - Check “Mute” is normal

5. HDMI test

Procedure - Test Signal : 720p,1080i


- Test Pattern : Any Pattern - Equipment: DVD Player with HDMI output - Display type must be set to 16:9Inspection item - HDMI TestCriteria - Ensure if the image is well performed and the color can not discolor.

4-9 Optical Performance Measure

Inspection Condition- Environment luminance: 5 Lux

- Product must be warmed up for 3 minutes

- Distances from the screen: 2.25 M

- Screen Size: 60 inches diagonal

- Reset to default before measurement

1. Test equipment

Procedure - Enter service mode:Press "Power→Left→ Left→Menu". - Select “RD test” - Select “Spoke On”

2. Brightness Procedure - Full white pattern - Use CL100 to measure brightness values of P1~P9. - Follow the brightness formula to calculate brightness values. ☼ Brightness Formula Avg.(P1~ P9)x1.1m2 Criteria - 800 lumens

Full white pattern


3. Ful On/Full Off Contrast Procedure - Full white pattern & full black pattern - Use CL100 to measure brightness values of full

white pattern P5 & full black pattern B5 ( see im-age: full white)

- Follow Contrast formula to calculate contrast values.

☼ Contrast Formula P5/B5 note: P5=center of white image B5=center of black image.Criteria - 1500:1

4. Uniformity

Procedure - Full white pattern - Use CL100 to measure brightness values of

P1~P9 (see image: full white). - Follow the Uniformity formula to calculate average values. ☼ Uniformity Formula ANSI Uniformity = Avg. (P1, P3, P7, P9) P5Criteria - 65%

4-11 Others

1. Functional Inspection

Keypad button - All keypad buttons must operate smoothly.

General - All OSD functions must be checked for functionality. When OSD menu is displayed, there

x 100%

Full black pattern


shall be no visible peaking, ringing, streaking, or smearing artifacts on the screen.

Factory Default - The factory settings (with appropriate centering, size, ge-ometry distortion, etc.) shall be displayed upon “Recall” is selected from OSD

Display Size - All preset modes shall expand to full screen size using OSD Horizontal and Vertical Size controls

Display Data Channel (DDC) - The purpose of the DDC test is to verify the DDC1/DDC2B operation of the projector and to verify Plug & Play function.

Acoustic - High pitch sound from cooling fan and color wheel is unac-ceptable.

2. Check points for exterior and print pattern

Check item Check point

Text & Pattern Missing letters & pattern or blurry prints are unacceptable

Exterior Dirt, scrape, water ripples and uneven color are unacceptable

Buttons Stuck buttons are unacceptableFocus ring Focus ring is functioning smoothly

Logo Missing logo, missing prints and blurry prints are unacceptable

Screw All screw sure be fixed and in right typePedestal Well-functionedLamp Cover It should be locked in the correct placePlastic Parts All plastic parts can not be brocken and damagedSafety or warning label

All safety and warning label should be visible, including all contents

Connector All interface connector should be complete and workable


Chapter 5

Firmware Upgrade5-1 Equipment Needed

Software : (DDP 2230- USB)- DLP Composer

- Firmware

- Library V7.1 0330 (library file has to put in PC and set right path in 5-4 step 4)

Hardware : - Projector

- Power cord (42.53506G002)

- USB Cable (42.87304G001)

- PC or Laptop


5-2 DLP Composer Lite Setup Procedure

1. Choose "DLP Composer Lite V7.1 Setup"

Program.

2. Click "Next" button.

3. Read "License Agreement".

- Choose "I accept and agree to be bound

by all the terms and conditions of this

License Agreement".

4. Click "Next".

5. Click "Next".

4

3


6. Click "Next".

7. Click "Next".

8. Writing system registry values.

9. Click "Finish".


5-3 USB Driver Upgrade Procedure

1. set up

- Plug in Power cord to projector.

- Link PC USB port and projector USB port

by USB Cable.

2. Execute Program

(1) "Found new hardware wiszard" will be

appearred on the screen.

(2) Select "Install the software automatically

(Recommended)".

(3) Then click "Next".

3. Finish

- Click "Finish" to end the installation.

(2)

(3)


5-4 Firmware Upgrade Procedure

1. Set-up

- Hold on "Power" and plug in power cord

while holding on "Power".

- Once the Power LED light on Blue & Red

at the same time, plug in USB cable into

the projector and link to the USB port of a

PC.

Note: The system fan and the light will not

operated.

2. Execute the "DLP ComposeTM" file.

3. Click "edit" and "perferences".

4. Click “Library.”

- Click the “browse” button and navigate to

the directory where you put the library file

in.


5. Select "Edit\preferences\Communications"

- Choose "USB".

- Click "OK".

6. Choose "Flash Loader".

- Click "Browse" to search the firmware file.

7. Selete the item "skip Boot Loader Area"

(select 32KB).

- Click "Reset Bus" to erase the flash

memory.

8. If the firmware is ready, click "start

download" to process the firmware

upgrade.

- Click "Yes" to erase the flash memory.


9. When firmware upgrade process is

finished, the unit return to stand-by status.

The LED power lights on and appears Red.

- Unplug USB cable and power cord and

replug in power cable.

10. Restart the unit and enter the service

mode to check the firmware version.

(To enter service mode, please refer to

Chapter 4 Function Test and Alignment

Procedure.)

32


Chapter 6

EDID Upgrade

6-1 EDID Introduction

Extended Display Identification Data is a VESA standard data format that contains basic

information about a display device and its capabilities, including vendor information,

maximum image size, color characteristics, factory pre-set timings, frequency range limits,

and character strings for the monitor name and serial number.

The information is stored in the display and is used to communicate with the system

through a Display Data Channel (DDC), which sites between the display device and the

PC graphics adapter. The system uses this information for configuration purposes, so the

monitor and system can work together.

Note: If a display device has digital input ports, like DVI or HDMI, but without EDID in its

main board, the display device will show no image while the input source is digital signal.


6-2 Equipment Needed

Software- EDID Program (Generic V0.51)

- EDID File (ACER_H5350 EDID-A04_USA.ini)

Hardware - Projector

- Generic Fixture (80.00001.001) for EDID Key-in (Fixture: JP3 must be closed)

- Power cord for Projector (42.53506G002)

- RS-232 9 Pin Cable (pin to pin, F-M) (42.83C07G001)

- Monitor

- PC

- VGA cable (42.87305G102)

- DVI Cable (42.83N06G001)

- Power adapter (47.57803G001) and power cord (42.53506G002) for fixture

- Adapter HDMI(M) to DVI-D(F) (42.82B13G001)


6-3 Setup Procedure (VGA)

1. Connect all ports

(1) Connect P1 of Fixture with COM Port of

PC/Laptop by RS232 Cable.

(2) Connect P2 of Fixture with VGA port of

Projector by VGA Cable.

(3) Plug Power Adapter to Power CNN.

(4) Plug Power Cord to H5350 unit.

Note: Confirm JP3 is "Close" status.

P1P2

Power CNN

VGA PortPower Port

VGA


6-4 EDID Key-In Procedure

1. Execute EDID Program

(1) Click on "EDID" to execute EDID

program.

2. Process

(1) Check the COM port is "COM 2"

(Select the COM port which you are

using).

(2) Click the "Model" button.

(3) Choose the source file

"ACER_H5350 EDID-A04_USA.ini"

and then open it.

3. Process

(1) Key in the serial number into the

barcode blank space.

(2) In "Write Source Select" item,select

"Analog".

(3) Click "Program" button.

4. Process

(1) "Please change the cable to Analog"

will be shown on the screen.

(2) Please press "Ok" button.

(1)

(2)

(3)

2

3

(3)

(1)

(2)

1

4


5

6

7

5. Finish

(1) "OK" will be shown on the screen.

6. Read EDID information

(1) In the Read item,select "Analog" and

"Trans".

(2) Please press "Read" button.


(1) EDID Informations will show the result.


6-5 Setup Procedure (HDMI)

1. Connect all ports

(1) Connect P1 of Fixture with COM Port of

PC/Laptop by RS232 Cable.

(2) Connect P2 of Fixture with P3 by DVI

Cable.

(3) Plug P4 to HDMI Port of the Projector.

(4) Plug Power Adapter to Power

CNN.

(5) Plug Power Cord to H5350 unit.

Note: Confirm JP3 is "Close" status.

P2

Power CNN

P1

P3

P4

Power PortHMDI Port


2. Process

(1) Check the COM port is "COM 2"

(Select the COM port which you are

using).

(2) Click the "Model" button.

(3) Choose the source file

"ACER_H5350 EDID-A04_USA.ini"

and then open it.

3. Process

(1) Key in the serial number into the

barcode blank space.

(2) In "Write Source Select" item,select

"Digital".

(3) Click "Program" button.

4. Process

(1) "Please change the cable to Digital"

will be shown on the screen.

(2) Please press "Ok" button.

2

3

(2)

4

(1)

(2)

(3)

(1)

(3)


5. Finish

(1) "OK" will be shown on the screen.


(1) In the Read item,select "Digital" and

"Trans".

(2) Please press "Read" button.


(1) EDID Informations will show the result.

5

7

(2)

6

(2)

(1)

H5350 Confidential �

Appendix A

ASSY FAN SHIELDING MODULE WHITE H5350

Item P/N Description Parts Supply70.89T13GR01 ASSY AXIAL FAN MODULE P5270(RMA)

1 85.1F123G260 SCREW PAN MECH E/SF M3*26 Ni NO2 49.88T01G001 SUNON, KDE1207PKV1-A 70*70*20mm

AXIAL FANNO

3 43.88N01G001 THERMAL SWITCH WITH BRACKET (KLIXON YS11) 100 DEG. C

1

2

3

H5350 Confidential ��

53

ASSY LAMP DRIVER MODULE H5350

1

2

4

6

H5350 Confidential ��

Item P/N Description Parts Supply1 42.00422G001 W.A 5P 150mm LAMP DRIVER TO MB X11602 42.00443G001 CABLE W.A, 2P #20 160mm LVPS TO BALLAST 3 42.00436G001 CABLE W.A. 2P #22 100mm LAMP DRIVER TO

LAMP X1160NO

4 51.88T11G003 HOLDER LAMP DRIVER FOR H5350 NO5 51.88T18G001 KAPTON 10*10 0.05t X1160 NO6 51.89T04G001 MYLAR LAMP DRIVER H5350 NO7 51.8AQ02G001 INTERLOCK SWITCH HOLDR FOR NEC NO

70.89T15GR01 ASSY LAMP DRIVER MODULE H5350(SERVICE)8 75.88T02G001 ASSY OSRAM LAMP DRIVER O6 MIC 180W NO9 75.88T05G001 ASSY INTERRUPT SWITCH MODULE XD1130

10 85.1A126G060 SCREW PAN MECH M3*6 NO11 85.3A122G040 SCREW CAP MECH M2*4 NI NO

H5350 Confidential IV

ASSY MAIN BD MODULE H5350

13

10

H5350 Confidential V

Item P/N Description Parts Supply70.89T11GR01 PCBA MAIN BD MODULE FOR H5350(SERVICE)

1 41.82G03G001 EMI GASKET USB CONNECTOR EP719 NO70.89T12GR01 ASSY I/O COVER MODULE H5350(SERVICE)

2 41.82K11G001 EMI GASKET W6*H1*L190mm NO3 41.83F21G001 GASKET h?/W*5, H*1.5, L*15 NO4 41.88T02G001 EMI GASKET L180*W4*H1 NO5 41.89B01G001 EMI TAPE L*190/W*13 NO6 51.88T04G011 IO COVER H5350 NO7 51.88T17G001 MYLAR MB SHELDING X1160 NO8 51.89T02G001 MB SHELDING MYLAR H5350 NO9 51.89T05G001 M/B SHIELDING MYLAR FOR H5350 NO

10 51.89T06G001 M/B CNNT MYLAR H5350 NO11 52.88T06G001 SPONGE CR4305 BACK MB SHELDING X1160 NO12 61.89T01G001 MAIN-BD SHIELDING H5350 NO13 80.89T01G001 PCBA MAIN BOARD FOR H5350 NO

H5350 Confidential VI

ASSY COLOR WHEEL MODULE H5350

Item P/N Description Parts Supply70.89T09GR01 ASSY COLOR WHEEL MODULE H5350(SERVICE)

1 23.89T19G001 YO R90Y35G90C35W28B82 6 SEGMENT CW NO2 51.82Y29G001 TAPE 3M J350 10*5mm FOR COLOR WHEEL NO3 52.83615G001 COLOR WHEEL DISC RUBBER , EzPro755 NO4 61.83628G001 COLOR WHEEL SHOULDER SCREW NICKEL M2*4.8 NO5 61.88N10G001 COLOR WHEEL HOLDER SECC,X15 NO6 80.87Y04G001 PCBA PHOTO SENSOR BOARD FOR PD72807 85.1A126G040 SCREW PAN MECH M2.6*4 Ni NO

H5350 Confidential VII

ASSY HOUSING MODULE H5350

H5350 Confidential VIII

Item P/N Description Parts Supply1 41.82B01G001 EMI GASKET W13*H10.5*L30mm NO2 41.89B02G001 EMI TAPE W*20/L*70 NO3 51.81540G001 TAPE 3M J350 17*60mm NO4 51.81541G001 TAPE 3M J350 17*30mm NO

70.89T14GR01 ASSY BOTTOM COVER MODULE H5350(SERVICE)

5 51.88T02G011 BOTTOM COVER H5350 NO6 51.88T14G001 ROD DUCT X1160 NO7 51.88T21G001 MYLAR K-LOCK 0.25t X1160 NO8 51.89T02G001 MB SHELDING MYLAR H5350 NO9 51.89T03G001 LVPS MYLAR H5350 NO

10 52.86801G011 RUBBER FOOT REAR GRAY H5350 NO11 52.88T04G001 BOTTOM SHELDING AIR TIGHT X1160 NO12 61.88T03G011 SHIELDING BOTTOM COVER FOR X1260 NO13 70.89T06G001 ASSY ADJUST FOOT MODULE WHITE H5350 NO14 85.1A123G060 SCREW PAN MECH M3*6 NI NO15 86.00122G015 NUT HEX M2.0*0.4P L15 Ni NO

H5350 Confidential IX

BUY ASSY TOP COVER ADD PAINT H5350

H5350 Confidential X

Item P/N Description Parts Supply70.89T16GR01 ASSY TOP COVER MODULE

H5350(SERVICE)1 51.88T01G012 TOP COVER,PC-MN3600H,WHITE H5350 NO2 51.88T07G001 LENS POWER X1160 NO3 51.88T08G002 IR CAP,WHITE H5350 NO4 51.88T16G011 TRACK REMOTE CONTROLLER,WHITE NO5 51.88T16G031 TRACK REMOTE CONTROLLER-2,WHITE NO6 85.1A526G060 Screw Pan M2.6x6 Ni NO7 51.88T06G011 KEYPAD POWER H5350 NO

17 20 717

618

9

12

33 115

814

2411

2810

530

13

29

27

2519

2

3

26

32

H5350 Confidential XI

17 20 717

618

9

12

33 115

814

2411

2810

530

13

29

27

2519

2

3

26

32

ASSY ENGINE MODULE H5350

H5350 Confidential XII

Item P/N Description Parts Supply1 11.009F0G007 CNNT F 203P FOR 720P LGA DMD SOCKET

70.89T10GR01 ASSY ENGINE MODULE H5350(SERVICE)2 23.88N06G001 YO PLASTIC RELAY FOR X15 NO3 23.88N20G001 YO CONDENSER1 FOR X15 NO4 23.88N20G011 YO CONDENSER2 FOR X15 NO5 23.89L01G001 PROJECTION LENS YM09W NO6 41.82B01G001 EMI GASKET W13*H10.5*L30mm NO7 41.85W05G001 EMI GASKET W8*H8*L45 NO8 48.86N01G003 DMD 1280x720 PIXEL 0.62” 720P LVDS9 51.00210G001 DMD SCREW WASHER A39 NO

10 51.89B01G001 HOLDER ZOOM RING X1260 NO11 51.89B04G001 ZOOM RING X126012 51.89F02G001 DMD INSULATION PC A15 NO13 51.89T01G001 FOCUS RING H535014 52.80J01G001 DMD ANTIDUST RUBBER 739 SILICONE RUBBER NO15 52.87319G001 DMD THERMAL PAD 18*13*0.5t16 61.80J10G001 DMD LIGHT MASK 739 SUS301 NO17 61.82B36G011 SCREW M3*10.5*6 IHSPC NO18 61.88611G001 DMD SCREW Ivy10X19 61.88N12G001 ROD SPRING SUS301,X15 NO20 61.89630G001 DP759 HEATSINK SPRING NO21 61.89F01G001 DMD PLATE AL A39 NO22 61.89F02G001 ROD COVER SUS304 0.25t 1/2H HD65 NO23 61.89F04G011 DMD HEATSINK AL H5350 NO24 70.89F04G001 PRE ASSY ENGINE BASE HD65 NO25 70.89F05G001 ASSY ROD MODULE HD65 NO26 70.89F15G001 ASSY ENGINE BOTTOM COVER HD65 NO27 70.89T04G001 ASSY COLOR WHEEL MODULE H5350 NO28 85.1A526G060 SCREW PAN MECH M2.6*6 Ni NYLOK NO29 85.4A121G065 SCREW FLAT HEAD TAP M1.7*6.5 NO30 87.FL000G003 WSHR FLAT 5.0*2.4*0.3 MYLAR NO31 51.88N43G001 MYLAR FOR RELAY BOTTOM NO32 51.88N41G001 MYLAR FOR MIRROR DEAMETER 3.5mm NO33 80.89T02G001 PCBA DMD BOARD FOR H5350

H5350 Confidential XIII

ASSY BOTTOM HOUSING MODULE H5350

32

13

24

17

31

26

21

22

23

15

330

9

6

5

19

12

16

2

25

2918

27

14

1

10

118

4

20

H5350 Confidential XIV

Item P/N Description Parts Supply1 41.83F21G001 GASKET h?/W*5, H*1.5, L*15 NO2 41.85A01G001 EMI GASKET / 10*27*20 NO3 41.88T01G001 EMI ? L85*W20 NO4 49.89B01G001 SPEAKER 2W 80HM NEOSONICA DAB128 300mm 5 51.81540G001 TAPE 3M J350 17*60mm NO6 51.88T19G001 MYLAR TOP SHELDING X1160 NO7 51.88T20G001 MYLAR LENS X1160 NO8 51.89B05G001 HOLDER SPEAKER X1260 NO9 51.89T08G001 TOP SHIELDING MYLAR FOR H5350 NO

10 52.89B02G001 SPONGE ML32 SPEAKER X1260 NO11 52.89B03G001 SPONGE SRS-48P SPEAKER X1260 NO12 61.87340G001 STAND OFF M3*4L D8.0 2100MP NO13 61.88T02G001 SHELDING TOP COVET X1160 NO14 61.88T09G001 BRKT INLET X1160 NO15 61.88T15G001 ACER LOGO FOR X116016 70.86L05G001 ASSY BLOWER FAN MODULE XD1250 NO17 70.89T01G001 ASSY TWO FAN SHIELDING X1260 NO18 23.89L01G001 PROJECTION LENS YM09W NO19 70.89T03G001 ASSY MAIN BD MODULE H5350 NO20 70.89T05G001 ASSY HOUSING MODULE H5350 NO21 70.89T07G001 ASSY LAMP DRIVER MODULE H5350 NO22 75.87J01G201 ASSY LVPS MATRITEK 200W EP752(2ndu)23 75.89T01G001 ASSY FRONT COVER H535024 85.1A123G060 SCREW PAN MECH M3*6 NI NO25 85.1A126G060 SCREW PAN MECH M2.6*6 Ni NO26 85.1A326G060 SCREW PAN HEAD MECH M2.6*6 BLACK NO27 85.1C123G060 SCREW PAN MECH W/T M3*6 NI NO28 85.1C224G051 SCREW PAN MECH M4*5 COLOR W/TOOTH NO29 85.3A113G050 STEP SCREW ψ3.5xH2.5 M3x5.0mm Ni NO30 85.ZA123G040 SCREW WCH/W MECH M3*4 Ni GREEN NO31 42.00455G002 W.A. 8P TO 16P 120mm MB TO LVPS H535032 49.86E02G001 SUNON, GB1245PKV1-8 45*20mm BLOWER

H5350 Confidential XV

A.K. H5350

8

7

9

1

2

3

4

5

6

10

H5350 Confidential XVI

Item P/N Description Parts Supply1 35.82001G111 AK LABEL 3”*3” BLANK NO2 36.00006G031 WARRANTY CARD ,EUROPE FOR ACER NO3 36.00027G001 SERVICE STATION CARD NO4 36.00029G001 SECURITY CARD FOR ACER NO5 36.88T02G001 QUICK START CARD MULTILINGUAL

ACER X1160/X1260 SERIESNO

6 36.89T01G001 USER’S GUIDE MULTILINGUAL (CD) ACER H5350

NO

7 42.00232G001 CABLE COMPOSITE VIDEO 2M YELLOW NO8 42.83M08G001 CABLE VGA 1.8M 15P BLUE 2400MP NO9 45.88T02G001 REMOTE CONTROLLER X1160+ Bontech

X2(WHITE)10 51.86213G002 PE BAG ZIPPER #9 W/RECYCLING MARK

FOR OPTOMANO

H5350 Confidential XVII

D.C. H5350

6

5

3

4

1

2

7

8

9

H5350 Confidential XVIII

Item P/N Description Parts Supply1 35.89T01G001 IO MYLAR FOR H5350 NO2 35.89T02G001 LOGO MYLAR FOR H5350

70.89T17GR01 ASSY LAMP COVER MODULE H5350(SERVICE)3 51.88T05G011 LAMP COVER H5350 NO4 61.00061G001 LOCK SCREW PAN MECH M3*8.5-3.5 Ni NO5 61.88T17G001 AL FOIL FOR LAMP COVER X1160 NO

SP.88T01GC01 LAMP MODULE FOR PROJECTOR X1160/12606 70.88T02G001 ASSY LAMP MODULE X1160 NO7 70.89T02G001 ASSY BOTTOM HOUSING MODULE H5350 NO8 75.88T03G022 BUY ASSY TOP COVER ADD PAINT H5350 NO9 85.1A323G080 SCREW PAN MECH M3*8 BLACK “GREEN” NO

H5350 Confidential XIX

D.P. H5350

19

12

9

4 3

1

13

11

18

10

17

15

6

7

8

14

2

16

5

H5350 Confidential XX

Item P/N Description Parts Supply1 35.00029G001 ACER TAPE 45M FOR CARTON NO2 35.52302G091 LABEL CARTON 108*92 BLANK NO3 35.82V02G001 LABEL CARTON(SEAL) 110*50mm PD120 NO4 35.86301G001 SPEC LABEL BLANK PD120 NO5 51.00200G001 HANDLE BAR 2. PE HD70 NO6 51.00201G001 HANDLE BAR 1.PE HD70 NO9 51.52109G003 PE BAG 450*350*0.07 FOR OPTOMA NO

10 53.88T01G001 SOFT CARRY BAG X1160 NO11 55.87202GC01 BOTTOM PAPER COVER PLATE 1230*1000*4mm

3200MPNO

12 55.87W04G001 CORNER PAPER P5271 NO13 55.88T02G001 CENTER PAPER BOX X1160 NO14 55.89T01G001 CARTON CARRY BOX H5350 NO15 56.88T03G001 AIR BAG TOP X1160+ NO16 56.88T04G001 AIR BAG BOTTOM X1160+ NO17 57.00001G001 PACK SIO2 DRIER 20g NO18 58.86201GC02 WOOD PALLET 48”*40*5”(DOUBLE FACE) FOR

CPC (MATERIALl PINE)NO

19 58.86202G001 COVER PALLET 1240*1020mm FOR EzPro 736 NO20 75.88T06G002 ASSY LENS CAP X116021 AK.89T01G001 A.K. H5350 NO 22 DC.89T01G001 D.C.H5350 NO23 42.00120G011 CABLE POWER CORD 1.8M SP-023/IS-14 EU-

ROPE DIS-WARNING LABEL24 42.00110G011 CABLE POWER CORD 1.8M SP-60/IS-14 UK DIS-

WARNING LABEL25 42.00131G011 CABLE POWER CORD 1.8M SP-027/IS-14 SWIT-

ZERLAND DIS-WARNING LABEL

H5350 Confidential XXI

Appendix B I. Serial Number System Definition

Serial Number Format for Projector

00J6601000 751 00001 59 10

1 2 3 4 5

1 : 00J6601000 = Part Number excluded “dot”

2 : 751 = Week Code(ex:2007 = 7,the fifty-one weeks of the year = 51)

3 : 00001 = Serial Numbers

4 : 59 = Manufacturing Code

5 : 10 = Eng. Version Code

H5350 Confidential XXII

II. PCBA Code Definition

PCBA Code for Projector

A B XXXXXXXXXXX CC XXX EEEE

1 2 3 4 5 6

1 : ID

2 : Vendor Code

3 : P/N

4 : Revision

5 : Date Code

6 : S/N

H5350 Service Manual Acer Proyector

Documents

Transcript of H5350 Service Manual Acer Proyector