Finall Ed Lab Manual 10092011
-
Upload
007pradeep -
Category
Documents
-
view
222 -
download
17
description
Transcript of Finall Ed Lab Manual 10092011
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
ELECTRONIC DEVICES
LAB MANUAL
IIIrd
SEMESTER B.E (E&C)
(For private circulation only)
RAJEEV GANDHI TECHNOLOGICAL UNIVERSITY
DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING
RADHARAMAN INSTITUTE OF RESEARCH &TECHNOLOGY
RATIBAD, BHOPAL
Prepared by:
PRADEEP RAGHUWANSHI,MTECH(LECTURER)
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
LIST OF EXPERIMENTS
1. V I Characteristics of PN Junction diode .
2. V I Characteristics of Zener diode.
3. V I Characteristics of Varactor Diode.
4. V I Characteristics of Schottky Diode.
5. V I Characteristics of Tunnel Diode.
6. V I Characteristics of Photo Transistor.
7. Study of Clipper & Clamper circuit.
8. Study of Half wave Rectifier with and without filter.
9. V I Common Emitter Configurations (BJT).
10. V I Characteristics of FET .
11. V I Characteristics of UJT.
12. V I Characteristics of Mosfet.
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no.1 P-N JUNCTION DIODE CHARACTERISTICS
AIMAIMAIMAIM:-To observe and draw the Forward and Reverse bias V-I Characteristics of
a P-N Junction diode.
APPARATUSAPPARATUSAPPARATUSAPPARATUS:-
THEORY:THEORY:THEORY:THEORY:----
CIRCUIT DIAGRAMsCIRCUIT DIAGRAMsCIRCUIT DIAGRAMsCIRCUIT DIAGRAMs::::----
FORWARDFORWARDFORWARDFORWARDBIAS:BIAS:BIAS:BIAS:----
REVERSE BIASREVERSE BIASREVERSE BIASREVERSE BIAS:-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
MODEL WAVEFORM:MODEL WAVEFORM:MODEL WAVEFORM:MODEL WAVEFORM:----
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
OBSERVATION:OBSERVATION:OBSERVATION:OBSERVATION:----
PRECAUTIONSPRECAUTIONSPRECAUTIONSPRECAUTIONS:-
1. All the connections should be correct.
2. Parallax error should be avoided while taking the readings from the Analog
meters.
RESULT:RESULT:RESULT:RESULT:---- Forward and Reverse Bias characteristics for a p-n diode is observed
Viva voice:-
1. What is atomic number?
2. What is the relation for the maximum number of electrons in each shell?
3. What are valence electrons?
4. What is forbidden energy gap?
5. What are conductors? Give examples?
S.NOS.NOS.NOS.NO
CURRENT CURRENT CURRENT CURRENT
THROUGHTHROUGHTHROUGHTHROUGH
APPLIED APPLIED APPLIED APPLIED
VOLTAGE(V)VOLTAGE(V)VOLTAGE(V)VOLTAGE(V)
VOLTAGE ACROSS VOLTAGE ACROSS VOLTAGE ACROSS VOLTAGE ACROSS
DIODE(V)DIODE(V)DIODE(V)DIODE(V)
CURRENT THROUGHCURRENT THROUGHCURRENT THROUGHCURRENT THROUGH
DIODE(mA)DIODE(mA)DIODE(mA)DIODE(mA)
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no. 2
ZENER DIODE CHARACTERISTICS
AIM: AIM: AIM: AIM: ---- a) To observe and draw the static characteristics of a zener diode
b) To find the voltage regulation of a given zener diode
APPARATUSAPPARATUSAPPARATUSAPPARATUS: -
THEORY:THEORY:THEORY:THEORY:----
CIRCUIT DIAGRAM:CIRCUIT DIAGRAM:CIRCUIT DIAGRAM:CIRCUIT DIAGRAM:----
STATIC CHARACTERISTICS:STATIC CHARACTERISTICS:STATIC CHARACTERISTICS:STATIC CHARACTERISTICS:----
OBSERVATIONS:OBSERVATIONS:OBSERVATIONS:OBSERVATIONS:-
Static characteristicsStatic characteristicsStatic characteristicsStatic characteristics:-
S.NO
ZENER VOLTAGE(VZ)
ZENER CURRENT(IZ)
Model waveform:-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
RESULT:-a) Static characteristics of zener diode are obtained and drawn.
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
b) Percentage regulation of zener diode is calculated.
PRECAUTIONS:- 1. The terminals of the zener diode should be properly identified
2. While determined the load regulation, load should not be immediately shorted.
3. Should be ensured that the applied voltages & currents do not exceed the ratings of the diode.
Viva voice:-
1. What are insulators? Give examples?
2. What are Semiconductors? Give examples?
3. What are the types of Semiconductor?
4. What is Intrinsic Semiconductor?
5. What is Extrinsic Semiconductor?
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no. 3
Characteristics of Varactor Diode
AIM: - To study and verify characteristics of Varactor Diode
APPRATUS REQURIED:-
THEORY:-
Circuit diagram:-
Reverse Breakdown Voltage and Reverse Leakage Current:-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
OBSERVATION TABLE:-
S.NO. VR IR BREAKDOWN VOLTAGE
RESULT:-
Viva voice:-
1. What is P-type Semiconductor?
2. What is doping?
3. What is N-type Semiconductor?
4. Which is majority and minority carrier in N-type Semiconductor?
5.which is majority and minority carrier in P-type Semiconductor?
6. What is depletion region in PN junction?
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no. 4
V-I Characteristics of Schottky Diode
AIM: - To study and verify characteristics of Schottky Diode
APPRATUS REQURIED:-
THEORY:-
Circuit symbol:-
Schottky diode schematic symbol
V-I CHARACTERISTICS:-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
FIG. Comparison of characteristics of hot-carrier and p-n junction diodes.
OBSERVATION TABLE:-
S.NO VD ID
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
RESULT:-
Viva voice:-
1. What is barrier voltage?
2. What is meant by biasing a PN junction?
3. What are the types of biasing a PN junction?
4. What is forward bias and reverse bias in a PN junction?
5. What is Reverse saturation current?
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no. 5
Characteristics of Tunnel Diode
AIM: - To verify the V-I characteristics of tunnel diode
APPRATUS REQURIED:-
THEORY:-
OBSERVATION TABLE:-
S.NO VT IT IP IV
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
V-I CHARACTERISTICS:-
FIG. Tunnel diode characteristics.
Viva voice:
1. Explain the construction, working, characteristics of PN junction diode?
2. Give the diode current equation?
3. Give two applications of PN junction diode.
4. What are semiconductors? Explain the types of semiconductors?
5. What is reverse break down?
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no. 6
Characteristics of Photo Transistor
AIM: - To study and verify characteristics of Photo Transistor.
APPRATUS REQURIED:-
THEORY:-
The fundamental behavior of photoelectric devices was introduced earlier with the description
of the photodiode. This discussion will now be extended to include the phototransistor, which
has a photosensitive collector–base p-n junction. The current induced by photoelectric effects is
the base current of the transistor. If we assign the notation for the photoinduced base
current, the resulting collector current, on an approximate basis, is
A representative set of characteristics for a phototransistor is provided in Fig. with the symbolic
representation of the device. Note the similarities betweenthese curves and those of a typical
bipolar transistor. As expected, an increase in lightintensity corresponds with an increase in
collector current. To develop a greater de-gree of familiarity with the light-intensity unit of
measurement, milli watts per square centimeter, a curve of base current versus flux density
appears in Fig.a Note the exponential increase in base current with increasing flux density. In
the same figure, a sketch of the phototransistor is provided with the terminal identification and
the angular alignment.
V-I Characteristics & Circuit symbol:-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Phototransistor: Fig (a) collector characteristics (b) symbol.
OBSERVATION TABLE:-
ICC VCC
RESULT:-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Viva voice:-
1. What is photo transistor?
2. Define the term diffusion capacitance.
3. What is break down? What are its types?
4. Define dynamic resistance.
5. What is the static resistance of a diode?
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no. 7
Clipper & Clamper circuit
AIM: - To design a Clipping circuit for the given specifications and hence to plot its O/P
APPARATUS REQUIRED:-
Theory:-
A clipping circuit consists of linear elements like resistors and non-linear elements like junction
diodes or transistors, but it does not contain energy-storage elements like capacitors. Clipping
circuits are used to select for purposes of transmission, that part of a signal wave form which
lies above or below a certain reference voltage level.
PROCEDURE: -
1. Connections are made as shown in the circuit diagram.
2. A sine wave Input Vi whose amplitude is greater than the clipping level is
applied.
3. Output waveform Vo is observed on the CRO.
4. Clipped voltage is measured and verified with the designed values
Series clippers:-
(a) To pass –ve peak above vr level:
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
(b) To pass +ve peak above vr level
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
CLAMPING CIRCUITS:-
AIM:- To design a Clamping circuit for the given specifications and hence to plot its output
APPARATUS REQUIRED:-
THEORY:-
(a)Positive peak clamped at Vr level :-
(b) Positive peak clamped at +ve Reference :-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
c) Positive peak clamped at –ve reference level :-
d) Negative peak clamped to Vr level :-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
f) Negative peak clamped at +ve reference level :-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
e) Negative peak clamped at –ve reference level :-
RESULT:-
Viva voice:-
1. What is clipper?
2. What is clamper?
3. Define dynamic conductance
4. Define the term transition capacitance?
5. What is meant by forward recovery time?
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no. 8
HALF – WAVE RECTIFIER
AIM: - To obtain the load regulation and ripple factor of a half-rectifier.
1. with Filter 2. without Filter
APPARATUS:-
THEORY:-
CIRCUIT DIAGRAM:-
OBSERVATIONS:-
WITHOUT FILTER:-
Vdc=Vm/π, Vrms=Vm/2, Vac=√ ( Vrms2- Vdc
2)
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Vm(v) Vac(v) Vdc(v) r= Vac/ Vdc
WITH FILTER:-
V1(V) V2(V)
Vdc=
(V1 +V2 )/2
Vac=
(V1 –V2 )/2√3
r =
Vac / Vdc
PRECAUTIONS:-
1. The primary and secondary sides of the transformer should be carefully identified.
2. The polarities of the diode should be carefully identified.
3. While determining the % regulation, first Full load should be applied and then it should be
decremented in steps.
RESULTS:-
Viva voice:-
1. What is a rectifier?
2. Explain the types of rectifier?
3. What is meant by reverse recovery time?
4. What are break down diodes?
5. Define storage time.
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no. 9
TRANSISTOR CE CHARACTERSTICS
AIM:- 1. To draw the input and output characteristics of transistor connected in
CE configuration
2. To find β of the given transistor.
APPARATUS:-
CIRCUIT DIAGRAM:-
OBSERVATIONS:-
INPUT CHARACTERISTICS:
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
MODEL GRAPHS:-
INPUT CHARACTERSTICS:-
OUTPUT CHARECTERSTICS:-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
PRECAUTIONS:-
1. The supply voltage should not exceed the rating of the transistor
2. Meters should be connected properly according to their polarities
RESULT:-
1. the input and out put characteristics of a transistor in CE configuration are Drawn
2. the β of a given transistor is calculated
Viva voice:-
1. What is transistor?
2. Why NPN transistor is preferred over PNP transistor?
3. What are the terminals present in a transistor?
4. Which of the terminal is heavily doped & which is lightly doped in BJT?
5. Why base is very thin in BJT?
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no. 10
FET CHARACTERISTICS
AIM: a). To draw the drain and transfer characteristics of a given FET.
b). To find the drain resistance (rd) amplification factor (µ) and
Trans conductance (gm) of the given FET.
APPARATUS: -
THEORY:-
CIRCUIT DIAGRAM:-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
OBSERVATIONS :-
DRAIN CHARACTERISTICS:-
MODEL GRAPH:-
TRANSFER CHARACTERISTICS:-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
DRAIN CHARACTERISTICS:-
PRECAUTIONS:-
1. The three terminals of the FET must be care fully identified
2. Practically FET contains four terminals, which are called source, drain, Gate,
substrate.
3. Source and case should be short circuited.
4. Voltages exceeding the ratings of the FET should not be applied.
RESULT :-
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Viva voice:-
1. What is FET?
2. Why FET is called unipolar device?
3. Why FET is called voltage controlled device?
4. What are the two main types of FET?
5. ) Define pinch off voltage in FET
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
Experiment no. 11
UJT CHARACTERISTICS
AIM:- To observe the characteristics of UJT and to calculate the Intrinsic Stand-Off
Ratio(η).
APPARATUS:-
THEORY:-
CIRCUIT DIAGRAM:-
V-I CHARACTERISTICS:-
A graph is plotted between VEE and IE for different values of VBE.
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
MODEL GRAPH:-
OBSEVATIONS:
CALCULATIONS: VP = ηVBB + VD
η = (VP-VD) / VBB
η = ( η1 + η2 + η3 ) / 3
INSTITUTE OF RESEARCH & TECHNOLOGY
ROLL NO: …………………. DATE: ………………
RESULT: The characteristics of UJT are observed and the values of Intrinsic Stand-Off
Ratio is calculated.
Viva voice:-
1. What is ujt?
2. What is instrinsic stand off ratio?