DRE Linear Guide

Dalian Running Engineering

E E-mail:[email protected] Website:www.dlrtr.com

Linear GuidewayHigh AccuracyBecause linear guide has little friction resistance, only a small driving force is needed to move the load. Lowfrictional resistance helps the temperature rising effect be small. Thus, the frictional resistance is decreasedand the accuracy could be maintained for long period than traditional slide system.

High RigidityThe design of Linear Guide rail and block features an equal lead rating in all four directions that requestsufficient rigidity load in all directions, and self-aligning capability to absorb installation-error. Moreover, asufficient preload can be achieved to increase rigidity and makes it suitable for any kind of installation.

Easy for MaintenanceCompared with high-skill required scrapping process of traditional slide system, the Linear Guide can offerhigh precision even if the mounting surface is machined by milling or grinding. Moreover theinterchangeability of Linear Guide gives a convenience for installation and future maintenance.

High SpeedLinear Guide block, rail and ball apply by contact point of Rolling system. Due to the characteristic of lowfrictional resistance, the required driving force is much lower than that in other systems, thus the powerconsumption is small. Moreover, the temperature rising effect is small even under high speed operation.

High Performance without Clearance

Even under a preload or regular load, the ball and raceway contact one another at two points in the loadingdirection, as shown. This design gives rise to a smooth rolling motion.



Model No.

Dimensionsof Assembly

(mm)Dimensions of Block (mm)

H H1 N W B B1 C L1 L K1 K2 G M×l T H2 H3

HGH15CA 28 4.3 9.5 34 26 4 26 39.4 61.4 10 4.85 5.3 M4×5 6 7.95 7.7

HGH20CA30 4.6 12 44 32 6

36 50.5 77.5 12.256 12 M5×6 8 6 6

HGH20HA 50 65.2 92.2 12.6

HGH25CA40 5.5 12.5 48 35 6.5

35 58 84 16.86 12 M6×8 8 10 9

HGH25HA 50 78.6 104.6 19.6

HGH30CA45 6 16 60 40 10

40 70 97.4 20.256 12 M8×10 8.5 9.5 13.8

HGH30HA 60 93 120.4 21.75

HGH35CA55 7.5 18 70 50 10

50 80 112.4 20.67 12 M8×12 10.2 16 19.6

HGH35HA 72 105.8 138.2 22.5

HGH45CA70 9.5 20.5 86 60 13

60 97 139.4 2310 12.9M10×17 16 18.5 30.5

HGH45HA 80 128.8 171.2 28.9

HGH55CA80 13 23.5 100 75 12.5

75 117.7 166.7 27.3511 12.9M12×18 17.5 22 29

HGH55HA 95 155.8 204.8 36.4

HGH65CA90 15 31.5 126 76 25

70 144.2 200.2 43.114 12.9M16×20 25 15 15

HGH65HA 120 203.6 259.6 47.8

Note:1kgf=9.81N



Model No.

Dimensions of Rail (mm)MountingBolt forRail

BasicDynamicLoadRating

BasicStaticLoadRating

Static RatedMoment

Weight

WR HR D h d P E (mm) C(kN)C0

(kN)MR

kN-mMP

kN-mMY

kN-mBlockkg

Railkg/m

HGH15CA 15 15 7.5 5.3 4.5 60 20 M4×16 11.38 16.97 0.12 0.1 0.1 0.18 1.45

HGH20CA20 17.5 9.5 8.5 6 60 20 M5×16

17.75 27.76 0.27 0.2 0.2 0.32.21

HGH20HA 21.18 35.9 0.35 0.35 0.35 0.39

HGH25CA23 22 11 9 7 60 20 M6×20

26.48 36.49 0.42 0.33 0.33 0.513.21

HGH25HA 32.75 49.44 0.56 0.57 0.57 0.69

HGH30CA28 26 14 12 9 80 20 M8×25

38.74 52.19 0.66 0.53 0.53 0.884.47

HGH30HA 47.27 69.16 0.88 0.92 0.92 1.16

HGH35CA34 29 14 12 9 80 20 M8×25

49.52 69.16 1.16 0.81 0.81 1.456.3

HGH35HA 60.21 91.63 1.54 1.4 1.4 1.92

HGH45CA45 38 20 17 14 105 22.5 M12×35

77.57 102.71 1.98 1.55 1.55 2.7310.41

HGH45HA 94.54 136.46 2.63 2.68 2.68 3.61

HGH55CA53 44 23 20 16 120 30 M14×45

114.44 148.33 3.69 2.64 2.64 4.1715.08

HGH55HA 139.35 196.2 4.88 4.57 4.57 5.49

HGH65CA63 53 26 22 18 150 35 M16×50

163.63 215.33 6.65 4.27 4.27 721.18

HGH65HA 208.36 303.13 9.38 7.38 7.38 9.82

Note:1kgf=9.81N



Note:1kgf=9.81N

Model No.




HGL15CA 24 4.3 9.5 34 26 4 26 39.4 61.4 10 4.85 5.3 M4×4 6 3.95 3.7

HGL25CA36 5.5 12.5 48 35 6.5

35 58 84 15.76 12 M6×6 8 5 5

HGL25HA 50 78.6 104.6 18.5

HGL30CA42 6 16 60 40 10

40 70 97.4 20.256 12 M8×10 8.5 6.5 10.8

HGL30HA 60 93 120.4 21.75

HGL35CA48 7.5 18 70 50 10

50 80 112.4 20.67 12 M8×12 10.2 9 12.6

HGL35HA 72 105.8 138.2 22.5

HGL45CA60 9.5 20.5 86 60 13

60 97 139.4 2310 12.9 M10×17 16 8.5 20.5

HGL45HA 80 128.8 171.2 28.9

HGL55CA70 13 23.5 100 75 12.5

75 117.7 166.7 27.3511 12.9 M12×18 17.5 12 19

HGL55HA 95 155.8 204.8 36.4



Note:1kgf=9.81N

Model No.




Static RatedMoment

Weight


(kN)MR

kN-mMP

kN-mMY

kN-mBlockkg

Railkg/m

HGL15CA 15 15 7.5 5.3 4.5 60 20 M4×16 11.38 16.97 0.12 0.1 0.1 0.14 1.45

HGL25CA23 22 11 9 7 60 20 M6×20

26.48 36.49 0.42 0.33 0.33 0.423.21

HGL25HA 32.75 49.44 0.56 0.57 0.57 0.57

HGL30CA28 26 14 12 9 80 20 M8×25

38.74 52.19 0.66 0.53 0.53 0.784.47

HGL30HA 47.27 69.16 0.88 0.92 0.92 1.03

HGL35CA34 29 14 12 9 80 20 M8×25

49.52 69.16 1.16 0.81 0.81 1.146.3

HGL35HA 60.21 91.63 1.54 1.4 1.4 1.52

HGL45CA45 38 20 17 14 105 22.5 M12×35

77.57 102.71 1.98 1.55 1.55 2.0810.41

HGL45HA 94.54 136.46 2.63 2.68 2.68 2.75

HGL55CA53 44 23 20 16 120 30 M14×45

114.44 148.33 3.69 2.64 2.64 3.2515.08

HGL55HA 139.35 196.2 4.88 4.57 4.57 4.27



Model No.Dimensionsof Assembly

Dimensions of Block (mm)

H H1 N W B B1 C L1 L K1 K2 G M T T1 H2 H3

HGW15CA 24 4.3 16 47 38 4.5 30 39.4 61.4 8 4.85 5.3 M5 6 8.9 3.95 3.7

HGW20CA30 4.6 21.5 63 53 5 40

50.5 77.5 10.256 12 M6 8 10 6 6

HGW20HA 65.2 92.2 17.6

HGW25CA36 5.5 23.5 70 57 6.5 45

58 84 11.86 12 M8 8 14 6 5

HGW25HA 78.6 104.6 22.1

HGW30CA42 6 31 90 72 9 52

70 97.4 14.256 12 M10 8.5 16 6.5 10.8

HGW30HA 93 120.4 25.75

HGW35CA48 7.5 33 100 82 9 62

80 112.4 14.67 12 M10 10.1 18 9 12.6

HGW35HA 105.8 138.2 27.5

HGW45CA60 9.5 37.5 120 100 10 80

97 139.4 1310 12.9 M12 15.1 22 8.5 20.5

HGW45HA 128.8 171.2 28.9

HGW55CA70 13 43.5 140 116 12 95

117.7 166.7 17.3511 12.9 M14 17.5 26.5 12 19

HGW55HA 155.8 204.8 36.4

HGW65CA90 15 53.5 170 142 14 110

144.2 200.2 23.114 12.9 M16 25 37.5 15 15

HGW65HA 203.6 259.6 52.8

Note:1kgf=9.81N



Model No.




Static RatedMoment

Weight


(kN)MR

kN-mMP

kN-mMY

kN-mBlockkg

Railkg/m

HGW15CA 15 15 7.5 5.3 4.5 60 20 M4×16 11.38 16.97 0.12 0.1 0.1 0.17 1.45

HGW20CA20 17.5 9.5 8.5 6 60 20 M5×16

17.75 27.76 0.27 0.2 0.2 0.42.21

HGW20HA 21.18 35.9 0.35 0.35 0.35 0.52

HGW25CA23 22 11 9 7 60 20 M6×20

26.48 36.49 0.42 0.33 0.33 0.593.21

HGW25HA 32.75 49.44 0.56 0.57 0.57 0.8

HGW30CA28 26 14 12 9 80 20 M8×25

38.74 52.19 0.66 0.53 0.53 1.094.47

HGW30HA 47.27 69.16 0.88 0.92 0.92 1.44

HGW35CA34 29 14 12 9 80 20 M8×25

49.52 69.16 1.16 0.81 0.81 1.566.3

HGW35HA 60.21 91.63 1.54 1.4 1.4 2.06

HGW45CA45 38 20 17 14 105 22.5 M12×35

77.57 102.71 1.98 1.55 1.55 2.7910.41

HGW45HA 94.54 136.46 2.63 2.68 2.68 3.69

HGW55CA53 44 23 20 16 120 30 M14×45

114.44 148.33 3.69 2.64 2.64 4.5215.08

HGW55HA 139.35 196.2 4.88 4.57 4.57 5.96

HGW65CA63 53 26 22 18 150 35 M16×50

163.63 215.33 6.65 4.27 4.27 9.1721.18

HGW65HA 208.36 303.13 9.38 7.38 7.38 12.89

Note:1kgf=9.81N



Model No.



H H1 N W B B1 C L1 L K1 K2 G M T T1 T2 H2 H3

HGW15CB 24 4.3 16 47 38 4.5 30 39.4 61.4 8 4.85 5.3 Ø4.5 6 8.9 6.95 3.95 3.7

HGW20CB30 4.6 21.5 63 53 5 40

50.5 77.5 10.256 12 Ø6 8 10 9.5 6 6

HGW20HB 65.2 92.2 17.6

HGW25CB36 5.5 23.5 70 57 6.5 45

58 84 11.86 12 Ø7 8 14 10 6 5

HGW25HB 78.6 104.6 22.1

HGW30CB42 6 31 90 72 9 52

70 97.4 14.256 12 Ø9 8.5 16 10 6.5 10.8

HGW30HB 93 120.4 25.75

HGW35CB48 7.5 33 100 82 9 62

80 112.4 14.67 12 Ø9 10.1 18 13 9 12.6

HGW35HB 105.8 138.2 27.5

HGW45CB60 9.5 37.5 120 100 10 80

97 139.4 1310 12.9 Ø11 15.1 22 15 8.5 20.5

HGW45HB 128.8 171.2 28.9

HGW55CB70 13 43.5 140 116 12 95

117.7 166.7 17.3511 12.9 Ø14 17.5 26.5 17 12 19

HGW55HB 155.8 204.8 36.4

HGW65CB90 15 53.5 170 142 14 110

144.2 200.2 23.114 12.9 Ø16 25 37.5 23 15 15

HGW65HB 203.6 259.6 52.8

Note:1kgf=9.81N



Model No.




Static RatedMoment

Weight


(kN)MR

kN-mMP

kN-mMY

kN-mBlockkg

Railkg/m

HGW15CB 15 15 7.5 5.3 4.5 60 20 M4×16 11.38 16.97 0.12 0.1 0.1 0.17 1.45

HGW20CB20 17.5 9.5 8.5 6 60 20 M5×16

17.75 27.76 0.27 0.2 0.2 0.42.21

HGW20HB 21.18 35.9 0.35 0.35 0.35 0.52

HGW25CB23 22 11 9 7 60 20 M6×20

26.48 36.49 0.42 0.33 0.33 0.593.21

HGW25HB 32.75 49.44 0.56 0.57 0.57 0.8

HGW30CB28 26 14 12 9 80 20 M8×25

38.74 52.19 0.66 0.53 0.53 1.094.47

HGW30HB 47.27 69.16 0.88 0.92 0.92 1.44

HGW35CB34 29 14 12 9 80 20 M8×25

49.52 69.16 1.16 0.81 0.81 1.566.3

HGW35HB 60.21 91.63 1.54 1.4 1.4 2.06

HGW45CB45 38 20 17 14 105 22.5 M12×35

77.57 102.71 1.98 1.55 1.55 2.7910.41

HGW45HB 94.54 136.46 2.63 2.68 2.68 3.69

HGW55CB53 44 23 20 16 120 30 M14×45

114.44 148.33 3.69 2.64 2.64 4.5215.08

HGW55HB 139.35 196.2 4.88 4.57 4.57 5.96

HGW65CB63 53 26 22 18 150 35 M16×50

163.63 215.33 6.65 4.27 4.27 9.1721.18

HGW65HB 208.36 303.13 9.38 7.38 7.38 12.89

Note:1kgf=9.81N



Model No.Dimensionsof Assembly

Dimensions of Block (mm)

H H1 N W B B1 C L1 L K1 K2 G M T T1 T2 H2 H3

HGW15CC 24 4.3 16 47 38 4.5 30 39.4 61.4 8 4.85 5.3 M5 6 8.9 6.95 3.95 3.7

HGW20CC30 4.6 21.5 63 53 5 40

50.5 77.5 10.256 12 M6 8 10 9.5 6 6

HGW20HC 65.2 92.2 17.6

HGW25CC36 5.5 23.5 70 57 6.5 45

58 84 11.86 12 M8 8 14 10 6 5

HGW25HC 78.6 104.6 22.1

HGW30CC42 6 31 90 72 9 52

70 97.4 14.256 12 M10 8.5 16 10 6.5 10.8

HGW30HC 93 120.4 25.75

HGW35CC48 7.5 33 100 82 9 62

80 112.4 14.67 12 M10 10.1 18 13 9 12.6

HGW35HC 105.8 138.2 27.5

HGW45CC60 9.5 37.5 120 100 10 80

97 139.4 1310 12.9 M12 15.1 22 15 8.5 20.5

HGW45HC 128.8 171.2 28.9

HGW55CC70 13 43.5 140 116 12 95

117.7 166.7 17.3511 12.9 M14 17.5 26.5 17 12 19

HGW55HC 155.8 204.8 36.4

HGW65CC90 15 53.5 170 142 14 110

144.2 200.2 23.114 12.9 M16 25 37.5 23 15 15

HGW65HC 203.6 259.6 52.8

Note:1kgf=9.81N



Model No.




Static RatedMoment

Weight


(kN)MR

kN-mMP

kN-mMY

kN-mBlockkg

Railkg/m

HGW15CC 15 15 7.5 5.3 4.5 60 20 M4×16 11.38 16.97 0.12 0.1 0.1 0.17 1.45

HGW20CC20 17.5 9.5 8.5 6 60 20 M5×16

17.75 27.76 0.27 0.2 0.2 0.42.21

HGW20HC 21.18 35.9 0.35 0.35 0.35 0.52

HGW25CC23 22 11 9 7 60 20 M6×20

26.48 36.49 0.42 0.33 0.33 0.593.21

HGW25HC 32.75 49.44 0.56 0.57 0.57 0.8

HGW30CC28 26 14 12 9 80 20 M8×25

38.74 52.19 0.66 0.53 0.53 1.094.47

HGW30HC 47.27 69.16 0.88 0.92 0.92 1.44

HGW35CC34 29 14 12 9 80 20 M8×25

49.52 69.16 1.16 0.81 0.81 1.566.3

HGW35HC 60.21 91.63 1.54 1.4 1.4 2.06

HGW45CC45 38 20 17 14 105 22.5 M12×35

77.57 102.71 1.98 1.55 1.55 2.7910.41

HGW45HC 94.54 136.46 2.63 2.68 2.68 3.69

HGW55CC53 44 23 20 16 120 30 M14×45

114.44 148.33 3.69 2.64 2.64 4.5215.08

HGW55HC 139.35 196.2 4.88 4.57 4.57 5.96

HGW65CC63 53 26 22 18 150 35 M16×50

163.63 215.33 6.65 4.27 4.27 9.1721.18

HGW65HC 208.36 303.13 9.38 7.38 7.38 12.89

Note:1kgf=9.81N



Model No.




EGH15SA24 4.5 9.5 34 26 4

- 23.1 40.1 14.83.5 5.7 M4×6 6 5.5 6

EGH15CA 26 39.8 56.8 10.15

EGH20SA28 6 11 42 32 5

- 29 50 18.754.15 12 M5×7 7.5 6 6

EGH20CA 32 48.1 69.1 12.3

EGH25SA33 7 12.5 48 35 6.5

- 35.5 59.1 21.94.55 12 M6×9 8 8 8

EGH25CA 35 59 82.6 16.15

EGH30SA42 10 16 60 40 10

- 41.5 69.5 26.756 12 M8×12 9 8 9

EGH30CA 40 70.1 98.1 21.05

EGH35SA48 11 18 70 50 10

- 45 75 28.57 12 M8×12 10 8.5 8.5

EGH35CA 50 78 108 20

Note:1kgf=9.81N



Model No.




Static RatedMoment

Weight


(kN)MR

kN-mMP

kN-mMY

kN-mBlockkg

Railkg/m

EGH15SA15 12.5 6 4.5 3.5 60 20 M3×16

5.35 9.4 0.08 0.04 0.04 0.091.25

EGH15CA 7.83 16.19 0.13 0.1 0.1 0.15

EGH20SA20 15.5 9.5 8.5 6 60 20 M5×16

7.23 12.74 0.13 0.06 0.06 0.152.08

EGH20CA 10.31 21.13 0.22 0.16 0.16 0.24

EGH25SA23 18 11 9 7 60 20 M6×20

11.4 19.5 0.23 0.12 0.12 0.252.67

EGH25CA 16.27 32.4 0.38 0.32 0.32 0.41

EGH30SA28 23 11 9 7 80 20 M6×25

16.42 28.1 0.4 0.21 0.21 0.454.35

EGH30CA 23.7 47.46 0.68 0.55 0.55 0.76

EGH35SA34 27.5 14 12 9 80 20 M8×25

22.66 37.38 0.56 0.31 0.31 0.666.14

EGH35CA 33.35 64.84 0.98 0.69 0.69 1.13

Note:1kgf=9.81N



Model No.




EGW15SA24 4.5 18.5 52 41 5.5

- 23.1 40.1 14.83.5 5.7 M5 5 7 5.5 6

EGW15CA 26 39.8 56.8 10.15

EGW20SA28 6 19.5 59 49 5

- 29 50 18.754.15 12 M6 7 9 6 6

EGW20CA 32 48.1 69.1 12.3

EGW25SA33 7 25 73 60 6.5

- 35.5 59.1 21.94.55 12 M8 7.5 10 8 8

EGW25CA 35 59 82.6 16.15

EGW30SA42 10 31 90 72 9

- 41.5 69.5 26.756 12 M10 7 10 8 9

EGW30CA 40 70.1 98.1 21.05

EGW35SA48 11 33 100 82 9

- 45 75 28.57 12 M10 10 13 8.5 8.5

EGW35CA 50 78 108 20

Note:1kgf=9.81N



Model No.




Static RatedMoment

Weight


(kN)MR

kN-mMP

kN-mMY

kN-mBlockkg

Railkg/m

EGW15SA15 12.5 6 4.5 3.5 60 20 M3×16

5.35 9.4 0.08 0.04 0.04 0.121.25

EGW15CA 7.83 16.19 0.13 0.1 0.1 0.21

EGW20SA20 15.5 9.5 8.5 6 60 20 M5×16

7.23 12.74 0.13 0.06 0.06 0.192.08

EGW20CA 10.31 21.13 0.22 0.16 0.16 0.32

EGW25SA23 18 11 9 7 60 20 M6×20

11.4 19.5 0.23 0.12 0.12 0.352.67

EGW25CA 16.27 32.4 0.38 0.32 0.32 0.59

EGW30SA28 23 11 9 7 80 20 M6×25

16.42 28.1 0.4 0.21 0.21 0.624.35

EGW30CA 23.7 47.46 0.68 0.55 0.55 1.04

EGW35SA34 27.5 14 12 9 80 20 M8×25

22.66 37.38 0.56 0.31 0.31 0.846.14

EGW35CA 33.35 64.84 0.98 0.69 0.69 1.45

Note:1kgf=9.81N



Model No.




EGW15SB24 4.5 18.5 52 41 5.5

- 23.1 40.1 14.83.5 5.7 Ø4.5 5 7 5.5 6

EGW15CB 26 39.8 56.8 10.15

EGW20SB28 6 19.5 59 49 5

- 29 50 18.754.15 12 Ø5.5 7 9 6 6

EGW20CB 32 48.1 69.1 12.3

EGW25SB33 7 25 73 60 6.5

- 35.5 59.1 21.94.55 12 Ø7 7.5 10 8 8

EGW25CB 35 59 82.6 16.15

EGW30SB42 10 31 90 72 9

- 41.5 69.5 26.756 12 Ø9 7 10 8 9

EGW30CB 40 70.1 98.1 21.05

EGW35SB48 11 33 100 82 9

- 45 75 28.57 12 Ø9 10 13 8.5 8.5

EGW35CB 50 78 108 20

Note:1kgf=9.81N



Model No.




Static RatedMoment

Weight


(kN)MR

kN-mMP

kN-mMY

kN-mBlockkg

Railkg/m

EGW15SB15 12.5 6 4.5 3.5 60 20 M3×16

5.35 9.4 0.08 0.04 0.04 0.121.25

EGW15CB 7.83 16.19 0.13 0.1 0.1 0.21

EGW20SB20 15.5 9.5 8.5 6 60 20 M5×16

7.23 12.74 0.13 0.06 0.06 0.192.08

EGW20CB 10.31 21.13 0.22 0.16 0.16 0.32

EGW25SB23 18 11 9 7 60 20 M6×20

11.4 19.5 0.23 0.12 0.12 0.352.67

EGW25CB 16.27 32.4 0.38 0.32 0.32 0.59

EGW30SB28 23 11 9 7 80 20 M6×25

16.42 28.1 0.4 0.21 0.21 0.624.35

EGW30CB 23.7 47.46 0.68 0.55 0.55 1.04

EGW35SB34 27.5 14 12 9 80 20 M8×25

22.66 37.38 0.56 0.31 0.31 0.846.14

EGW35CB 33.35 64.84 0.98 0.69 0.69 1.45

Note:1kgf=9.81N



ModelNo.



H H1 N W B B1 C L1 L G Gn M×l H2

MGN5C 6 1.5 3.5 12 8 2 - 9.6 16 - 0.8 M2×1.5 1

MGN7C8 1.5 5 17 12 2.5

8 13.5 22.5- Ø1.2 M2×2.5 1.5

MGN7H 13 21.8 30.8

MGN9C10 2 5.5 20 15 2.5

10 18.9 28.9- Ø1.4 M3×3 1.8

MGN9H 16 29.9 39.9

MGN12C13 3 7.5 27 20 3.5

15 21.7 34.7- Ø2 M3×3.5 2.5

MGN12H 20 32.4 45.4

MGN15C16 4 8.5 32 25 3.5

20 26.7 42.14.5 M3 M3×4 3

MGN15H 25 43.4 58.8

Note:1kgf=9.81N



ModelNo.




Static RatedMoment

Weight


(kN)MR

kN-mMP

kN-mMY

kN-mBlockkg

Railkg/m

MGN5C 5 3.6 3.6 0.8 2.4 15 5 M2×6 0.54 0.84 2 1.3 1.3 0.008 0.15

MGN7C7 4..8 4.2 2.3 2.4 15 5 M2×6

0.98 1.24 4.7 2.84 2.84 0.010.22

MGN7H 1.37 1.96 7.64 4.8 4.8 0.015

MGN9C9 6.5 6 3.5 3.5 20 7.5 M3×8

1.86 2.55 11.76 7.35 7.35 0.0160.38

MGN9H 2.55 4.02 19.6 18.62 18.62 0.026

MGN12C12 8 6 4.5 3.5 25 10 M3×8

2.84 3.92 25.48 13.72 13.72 0.0340.65

MGN12H 3.72 5.88 38.22 36.26 36.26 0.054

MGN15C15 10 6 4.5 3.5 40 15 M3×10

4.61 5.59 45.08 21.56 21.56 0.0591.06

MGN15H 6.37 9.11 73.5 57.82 57.82 0.092

Note:1kgf=9.81N



ModelNo.



H H1 N W B B1 C L1 L G Gn M×l H2

MGW5C6.5 1.5 3.5 17

13 2 -14.1 20.5 - Ø0.8

M2.5×1.51

MGW5CL - 8.5 6.5 M3-THRU

MGW7C9 1.9 5.5 25 19 3

10 21 31.2- Ø1.2 M3×3 1.85

MGW7H 19 30.8 41

MGW9C12 2.9 6 30

21 4.5 12 27.5 39.3- Ø1.2 M3×3 2.4

MGW9H 23 3.5 24 38.5 50.7

MGW12C14 3.4 8 40 28 6

15 31.3 46.1- Ø1.2 M3×3.6 2.8

MGW12H 28 45.6 60.4

MGW15C16 3.4 9 60 45 7.5

20 38 54.85.2 M3 M4×4.2 3.2

MGW15H 35 57 73.8

Note:1kgf=9.81N

Note:1kgf=9.81N

ModelNo.




Static RatedMoment

Weight

WR WB HR D h d P E (mm) C(kN)C0(kN)

MRkN-m

MPkN-m

MYkN-m

Blockkg

Railkg/m

MGW5C10 - 4 5.5 1.6 3 20 5 M2.5×7 0.68 1.18 5.5 2.7 2.7 0.016 0.34

MGW5CL

MGW7C14 - 5.2 6 3.2 3.5 30 10 M3×6

1.37 2.06 15.7 7.14 7.14 0.020.51

MGW7H 1.77 3.14 23.45 15.53 15.53 0.029

MGW9C18 - 7 6 4.5 3.5 30 10 M3×8

2.75 4.12 40.12 18.96 18.96 0.040.91

MGW9H 3.43 5.89 54.54 34 34 0.057

MGW12C24 - 8.5 8 4.5 4.5 40 15 M4×8

3.92 5.59 70.34 27.8 27.8 0.0711.49

MGW12H 5.1 8.24 102.7 57.37 57.37 0.103

MGW15C42 23 9.5 8 4.5 4.5 40 15 M4×10

6.77 9.22 199.34 56.66 56.66 0.1432.86

MGW15H 8.93 13.38 299.01 122.6 122.6 0.215


GGYArc rolling guide

Spec and code GGY16/168AA(AB) GGY16/228AA(AB) GGY16/300AA(AB) GGY16/390AA(AB) GGY25/230AA(AB)

Assembly

dimension

H 24 24 24 24 37

B1 47 47 47 47 70

Block dimension

B2 4.5 4.5 4.5 4.5 6.5

B3 38 38 38 38 57

K 19.4 19.4 19.4 19.4 30.5

L1 58 58 58 58 79.5

L2 40.5 40.5 40.5 40.5 59

L3 30 30 30 30 45

M M5 M5 M5 M5 M8

φ 4.5 4.5 4.5 4.5 7

L4 2.5 2.5 2.5 2.5 11

Oil cup dimension G Φ4 Φ4 Φ4 Φ4 M6

N 4 4 4 4 6

Guide dimension

B4 16 16 16 16 23

H1 15 15 15 15 22

dxDxh 4.5x7.5x5.3 4.5x7.5x5.3 4.5x7.5x5.3 4.5x7.5x5.3 7x11x9

Θ2 15° 15° 15° 15° 15°

R0 168 228 300 390 230

R1 160 220 292 382 218.5

R2 176 236 308 398 241.5

Θmax 160° 160° 75° 65° 160°

Angle Θ1 3° 3° 2° 2° 3°

Dynamic load C(KN) 5.67 5.67 5.67 5.67 16.8

Static load C0(KN) 6.35 6.35 6.35 6.35 21.5

Torque rating

MA(N.m) 51.8 51.8 51.8 51.8 142.2

MB(N.m) 51.8 51.8 51.8 51.8 142.2

MC(N.m) 82.9 82.9 82.9 82.9 233.5

weight Block/pc 0.2 0.2 0.2 0.2 0.99

Guide/pc 1.5 1.5 1.5 1.5 3.3

11 E-mail:[email protected] Website:www.dlrtr.com

Dalian Running EngineeringGZD Roller Guide Block

1. Description(1) The roller guide block is a precision linear guide component. It has stronger loading capacity and higher rigidity. Inthe condition of high frequency back and forth such as repetitive motion, starting and stopping, it can reduce weight ofcomplete machine, transmission gearing and power cost.(2) The roller guide block can reach higher sensitivity and high performance of plane linear motion. In the condition ofheavy load or varied load it has small elastic deformation and get stable linear motion without crawl.(3) The roller guide block can center automatically because its rolling body-roller has good guiding performance inrolling. Therefore the positioning accuracy can be improved.(4) The rollers in the roller guide block move circularly. Therefore there is no length limit of machine tools by usingroller guide block. The quantity of guide block depends on loading capacity and specification.(5) The roller guide block has wide application. The small type of guide block can be used for linear motion parts ofmould and instrument. The large type of guide block is used for plane linear motion of heavy machine tools andprecision instrument, especial for NC, CNC machine tools.

2. Basic structureThe roller block is consisted of block, roller and re-circulator. The rollers are doing circulating motion in the block whichare hardened by quenching and precisely ground. To prevent the roller run out of the block, rollers are designed as steprollers and block designed with special slot, which made the rollers to center automatically and avoid excursion inmoving. It is in favor of flexible movement under load and has long lifetime.

3. Dimension

Model GZD15x53 GZD20x70 GZD30x123 GZD40x132

Length L 52.8 70 123 132

Width W 26.5 30 40 51.4

Height H 15 20 30 40

Dia for mounting hole dxDxh 0.34 0.3x0.6x4 0.45x0.85x5 0.55x0.10x6

Center distance of

mounting hole

A 19 26 58 50.8

B 19.3 23 30 41.5

Basic rated Static load C0(KN) 29.0 53.4 72.3 121

dynamic load C(KN) 23.0 38.3 63.5 89.1

Weight Block Per/pc 0.12 0.25 0.92 1.7


Dalian Running EngineeringGZV precision roller cross guide

1. Structure

"RTR" cross roller guide consists of two rails with V shape groove, retainer and cylinder roller. The cylinder rollers, which

range crosswise each other, reciprocating along precisely ground V shape groove. It can sustain the load from all direction

and achieve high accuracy and smooth linear motion.

2. Feature

Small rolling friction, good stability;

Small start friction, good following function;

Large contact area, small elastic deformation, many efficient motion units, easy motion with high rigidity and load;

Flexible structure design, convenient installation and using；3. Calculation of loadTravel length and quantity of roller

4.basic dimension of roller cross guide

SpecificationDimension GZV1 GZV2 GZV3 GZV4 GZV6 GZV9 GZV12 GZV15

A 8.5 12 18 22 31 44 58 71

H 4 6 8 11 15 22 28 36

W 3.8 5.5 8.1 10 14.2 20.2 27 33

M M2 M3 M4 M5 M6 M8 M10 M12

D - - 6 7.5 9.5 10.5 13.5 16.5

h - - 3.1 4.1 5.2 6.2 8.2 10.2

G 1.8 2.5 3.5 4.5 6 9 12 14

F 10 15 25 40 50 50 100 100

T 2 2 3 3 3 4 5 5

Max rail LMAX 80 180 300 500 500 1400 1400 1400

Weight of one

Rail per meter (kg)0.10 0.23 0.45 0.75 1.47 3.07 5.32 S.30


1. Calculation of guide lengthThe length of guide is more than 1.5 times of travel: L≥1.5l;In formula: L-guide length (mm) l-travel length (mm)2. The length of retainer: K≤L-l/2In formula: K-retainer length (mm)3. Calculation of roller quantity: N=(K-2a)/f+1In formula: N: roller quantity (decimal fraction is not calculated) a-enddistance of retainer f-roller interval

DRE Linear Guide

Documents

Transcript of DRE Linear Guide