Chlorination / DeChlorination Procedures - PNWS-AWWA

70
Chlorination / DeChlorination Procedures -A New Twist to an Old Technology- Robert Gordhamer Measurement Technologies, Inc. Redmond, Washington

Transcript of Chlorination / DeChlorination Procedures - PNWS-AWWA

Page 1: Chlorination / DeChlorination Procedures - PNWS-AWWA

Chlorination / DeChlorinationProcedures

-A New Twist to an Old Technology-

Robert Gordhamer

Measurement Technologies, Inc.

Redmond, Washington

Page 2: Chlorination / DeChlorination Procedures - PNWS-AWWA

Chlorination / Dechlorination

• Field Chlorination– Forms of chlorine– Reducing the amount of chlorine– Methods of chlorination

• Field Dechlorination– Discharge requirements– Dechlorination chemicals– Methods of dechlorination

Page 3: Chlorination / DeChlorination Procedures - PNWS-AWWA

FIELD CHLORINATION

• AWWA/ANSI C651-05– Disinfecting Water Mains

• First standard approved Sept. 30, 1947• Latest revision June 1, 2005

– Standards are reviewed every five years.– AWWA standards describe minimum

requirements AND is not a SPECIFICATION.

Page 4: Chlorination / DeChlorination Procedures - PNWS-AWWA

Forms of Chlorine

*It is recommended that you follow the current AWWA C651 specification with the following modifications.

Sodium hypochlorite (NaOCl) solution...

Liquid chlorine (Cl2)...

Calcium hypochlorite (Ca(OCl)2) granules or tablets...

Page 5: Chlorination / DeChlorination Procedures - PNWS-AWWA

FIELD CHLORINATION

• Liquid Chlorine– Least expensive with the highest danger.– Requires specially trained treatment crews.– Requires safety equipment for the operator

and all other personnel at the site.– Requires containment container for cylinder.

Page 6: Chlorination / DeChlorination Procedures - PNWS-AWWA

FIELD CHLORINATION

• Calcium Hypochlorite (HTH)– Available in two forms

• Tablets• Granular

– Contains approximately 65% available chlorine.

– Placed in pipeline during construction.– Recommended to be used in pipe sizes to 24”

diameter.

Page 7: Chlorination / DeChlorination Procedures - PNWS-AWWA

FIELD CHLORINATION

• Sodium Hypochlorite– Contains between 5% to 15% available

chlorine. (12.5% typical)– Available in 1 qt. to 55 gallon containers.– Must be stored properly to prevent

deterioration.– Must be NSF 60, household bleach is not an

acceptable chlorine.

Page 8: Chlorination / DeChlorination Procedures - PNWS-AWWA

What determines how hot you cook the line …

• Chlorine Residual Level…– The specifier determines the chlorine

residual level the line should be targeted for?

– Did your crews let dirt get into the pipeline during the installation?

– Did you not seal the pipeline at night? Could there be animals inside the line?

Page 9: Chlorination / DeChlorination Procedures - PNWS-AWWA

How can I use less

Chlorine…

Page 10: Chlorination / DeChlorination Procedures - PNWS-AWWA

Alternate Procedures

Page 11: Chlorination / DeChlorination Procedures - PNWS-AWWA

Alternate Procedures

Page 12: Chlorination / DeChlorination Procedures - PNWS-AWWA

Disinfecting Water MainsBasic Disinfection Procedure

1. Inspect materials to insure their integrity.2. Preventing contaminating materials from

entering the watermain.3. Remove, by flushing those materials that

may have entered the line.4. Pressure test new installation.5. Chlorinating the new installation

cont.

Page 13: Chlorination / DeChlorination Procedures - PNWS-AWWA

Disinfecting Water MainsBasic Disinfection Procedure

6. Document that an adequate level of chlorine contacted each pipe.

7. Flushing the highly chlorinated water from the main.

8. Determining the bacteriological quality by laboratory test after disinfection.

9. Final connection of the approved new water main to the active distribution system.

Page 14: Chlorination / DeChlorination Procedures - PNWS-AWWA

How do you COOK a line?

Tablet or Granular

Continuous-feed method

Slug method

NOW...

Page 15: Chlorination / DeChlorination Procedures - PNWS-AWWA

By using aModified Continuous-Feed

method.

• Mixes the chlorine solution with every gallon of water that is filling your new system. This will insure total contact at the desired chlorine residual level.

Page 16: Chlorination / DeChlorination Procedures - PNWS-AWWA

Why use a combination Venturi / Orifice Design?

Reliability

Page 17: Chlorination / DeChlorination Procedures - PNWS-AWWA

How does an Orifice design work?

Page 18: Chlorination / DeChlorination Procedures - PNWS-AWWA

The size of the orifice determines performance.

Page 19: Chlorination / DeChlorination Procedures - PNWS-AWWA

How does a venturi design work?

Page 20: Chlorination / DeChlorination Procedures - PNWS-AWWA
Page 21: Chlorination / DeChlorination Procedures - PNWS-AWWA

The lateral by-pass venturi works by combining two principles together…

• 2” Mainline orifice.

Plus three additional orifice insert…

And,

Page 22: Chlorination / DeChlorination Procedures - PNWS-AWWA

And the lateral by-pass venturi…

Page 23: Chlorination / DeChlorination Procedures - PNWS-AWWA

Side view -Showing the mainline orifice ring.

By inserting the smaller orifices you can control your discharge rate OR increase by-pass pressure to insure a full vacuum is achieved.

This orifice directs part of the water flow into the lateral by-pass venturi.Flow direction

Page 24: Chlorination / DeChlorination Procedures - PNWS-AWWA

Incoming water flow

Pressurizes the lateral by-pass to start the vacuum.

Page 25: Chlorination / DeChlorination Procedures - PNWS-AWWA

When the by-pass waterre-enters the main flow, it will

enter at thehigher incoming pressure.

Page 26: Chlorination / DeChlorination Procedures - PNWS-AWWA

The Pros & Cons ofVenturi / Orifice designs…

• The smaller the opening , the quicker you get a vacuum, HOWEVER, you take away high flow performance.

• The larger the opening, the higher the flow must be before a vacuum is achieved. This takes away low end performance.

Page 27: Chlorination / DeChlorination Procedures - PNWS-AWWA

Lateral By-Pass VenturiDesign with Mainline Orifice…

• FEATURES:– Full vacuum throughout entire flow

range.– Wide range of FLOW.– Controllability of feed solution.

Page 28: Chlorination / DeChlorination Procedures - PNWS-AWWA

Lateral By-Pass VenturiDesign with Mainline Orifice…

• CONSISTENT FEED RATE:– ONE GALLON per minute, FROM

START TO FINISH.– Feed control valve allows for proper

balancing of feed solution.– Gives operator the ability to make feed

solution strength based on flow.

Page 29: Chlorination / DeChlorination Procedures - PNWS-AWWA

Chlorinating Set-Up

Page 30: Chlorination / DeChlorination Procedures - PNWS-AWWA

Source Hydrant

Any length of hose can be attached in front of the venturi device...

Page 31: Chlorination / DeChlorination Procedures - PNWS-AWWA

Chlorinating Set-Up

Source Hydrant

No outside power required when you use a venturi style device.

Enter point

Page 32: Chlorination / DeChlorination Procedures - PNWS-AWWA

Chlorinating Set-Up

Page 33: Chlorination / DeChlorination Procedures - PNWS-AWWA

Testing for CRL

• Locate sampling points, having the first point within ten feet of the entry point.

• Number of sampling points to be determined by the size of the project.

Page 34: Chlorination / DeChlorination Procedures - PNWS-AWWA

Set-up Discharge area

• You will need to discharge water from the system during the chlorinating operation.

• Some of this water will have a chlorine residual level that needs to be neutralized.

Page 35: Chlorination / DeChlorination Procedures - PNWS-AWWA

Entry Point

Page 36: Chlorination / DeChlorination Procedures - PNWS-AWWA

Device with Test Port

Page 37: Chlorination / DeChlorination Procedures - PNWS-AWWA

Taking a test sample

Page 38: Chlorination / DeChlorination Procedures - PNWS-AWWA

Procedure for chlorinating the system

• Adjust feed control valve to full open position.• Turn on the water supply to start filling.• Test chlorine residual level at a sample point

within ten feet of the entry point.• Follow Engineer’s specifications on the chlorine

residual level.• Take test samples at selected sites throughout

the project.• Adjust the control valve to increase or decrease

the amount of chlorine entering the system.

Page 39: Chlorination / DeChlorination Procedures - PNWS-AWWA

COOK

Page 40: Chlorination / DeChlorination Procedures - PNWS-AWWA

Dechlorinate

Page 41: Chlorination / DeChlorination Procedures - PNWS-AWWA

LiabilityIf you allow chlorinated water to be discharge into the environment and you have not enforced your state regulations, YOU will share in the responsibility. OR, in other words the fine.This will be true for the consulting engineer, the owner and the person or company that discharges the chlorinated water.

Page 42: Chlorination / DeChlorination Procedures - PNWS-AWWA

EPA has set guidelines…

• The US-EPA has a recommended set of guidelines.– Each state has adapted there own standards.– Some states, have even broken it down into

regions.• However, all states have discharge limits

on chlorine or chloraminated water.• AWWA is developing a new dechlorination

standard.

Page 43: Chlorination / DeChlorination Procedures - PNWS-AWWA

And, it’s good for the Environment…

• Even a trace of chlorine will kill fish.

• Your discharge water effects the beginning of the food chain.

Page 44: Chlorination / DeChlorination Procedures - PNWS-AWWA

Washington, Oregon and Idaho’sRequirements

• Regulation Standard:– State Controlled

• DISCHARGE LIMITS:– Fresh Water CMC (Acute)

• 19 ug/L– Fresh Water CCC (Chronic)

• 11 ug/L

Page 45: Chlorination / DeChlorination Procedures - PNWS-AWWA

mg/L vs. ug/L

• mg/L means milligrams per liter or parts per million (PPM).

1 mg/L = 1 PPM

• ug/L means micrograms per liter or parts per billion (PPB).

1 ug/L = 1 PPB

Page 46: Chlorination / DeChlorination Procedures - PNWS-AWWA

Convertug/L (PPB) to mg/L (PPM)

• To convert micrograms per liter to milligrams per liter, divide by 1000.

• 11 ug/L divided by 1000 = 0.011 mg/L• 19 ug/L divided by 1000 = 0.019 mg/L

• .8 mg/L multiplied by 1000 = 800 ug/L PPB

Page 47: Chlorination / DeChlorination Procedures - PNWS-AWWA

What you should know…

So, you are going to specify DECHLORINATION.

There are many different styles of dechlorination devices, so be sure, that if you specify a device that it works at the chlorine residual levels that

will be encountered.

Page 48: Chlorination / DeChlorination Procedures - PNWS-AWWA

LiabilityConsideration should be given to specifying

only the performance that is needed and let the contractor determine what

equipment to use to achieve the chlorine residual level specified for the discharge.

This way you do not assume liability on what equipment was used.

Page 49: Chlorination / DeChlorination Procedures - PNWS-AWWA
Page 50: Chlorination / DeChlorination Procedures - PNWS-AWWA

Dechlorination

• Two major methods of Dechlorination– Non-Chemical Dechlorination

• Only to be used for low chlorinated water.• Chloraminated water can take 3 – 4 times longer to

decay the chlorine residual.– Chemical Dechlorination

• Faster and more predictable method.• Available in solid, liquid and gaseous forms.• Works well with chloraminated water.

Page 51: Chlorination / DeChlorination Procedures - PNWS-AWWA

Non-Chemical Methodsfor Dechlorination

• Holding Tanks or Ponds• Land Applications• Groundwater recharge• Releases though hay bales• Discharge into Strom Sewers• Discharges into Sanitary Sewers

Page 52: Chlorination / DeChlorination Procedures - PNWS-AWWA

Chemical methodsfor Dechlorination

Types of Chemical Dechlorination

• Drip – style devices• Injection Pumps• Passive device• Vacuum - Induced

Page 53: Chlorination / DeChlorination Procedures - PNWS-AWWA

Forms of Dechlorination Equipment

• Passive– A device which requires that the water

discharge to make contact with the dechlorination chemical.

• Vacuum-induced– Any device that produces a vacuum and

provides a means of controlling the flow of dechlorination chemical.

Page 54: Chlorination / DeChlorination Procedures - PNWS-AWWA

Tablet style devices

Page 55: Chlorination / DeChlorination Procedures - PNWS-AWWA

Liquid Feed style devices

Page 56: Chlorination / DeChlorination Procedures - PNWS-AWWA
Page 57: Chlorination / DeChlorination Procedures - PNWS-AWWA

Dechlorination Chemicals

Common chemicals used in field dechlorinationSodium Sulfite

Sodium ThiosulfateSodium Bisulfite

Ascorbic acidSodium Ascorbate

Calcium Thiosulfate

Page 58: Chlorination / DeChlorination Procedures - PNWS-AWWA

Why should you use only environmentally safe chemicals

• We are neutralizing the chlorine to protect aquatic life.

• We have to be aware of pH.• NO effect dissolved oxygen in the water.• Safe for humans to handle.• Easier shipping and handling of freight.

Page 59: Chlorination / DeChlorination Procedures - PNWS-AWWA

What chemicals are safe for aquatic life?

• Calcium Thiosulfate (Domestic)– Liquid solution

• Ascorbic acid (Imported)– Granular or tablet form

• Sodium Ascorbate (Imported)– Granular form only

Page 60: Chlorination / DeChlorination Procedures - PNWS-AWWA

Cost comparison of chemicals that are safe for aquatic life?

• Calcium Thiosulfate (Domestic)– Low cost

• Ascorbic acid (Imported)– Granular – three times the cost– Tablet – five times the cost

• Sodium Ascorbate (Imported)– Granular – over 6 times the cost

Page 61: Chlorination / DeChlorination Procedures - PNWS-AWWA

Basic Dechlorination Procedure

• The selected dechlorination process must be able to neutralize the chlorine to levels below 0.01 mg/l.

• Testing needs to be done at the point of discharge, the point you lose control of the water flow.

• Spread dechlorination chemical in the path of the discharge water to insure that the initial water will make contact with the chemical.

Page 62: Chlorination / DeChlorination Procedures - PNWS-AWWA

Basic Dechlorination Procedure

• Make sure that either your feed solution or your tablet chamber has the proper amount of chemical to handle the chlorine residual to be neutralized.

• Start your discharge and check your chlorine residual at the discharge point.

• Make any adjustments that may require proper neutralization of chlorine.

Page 63: Chlorination / DeChlorination Procedures - PNWS-AWWA

Basic Dechlorination Procedure

• If using a manufactured device follow the manufacturers directions.

• Monitor chlorine residual at per determine times during the discharge and record in log book.

• When you achieve the desired chlorine residual level in your discharge water, stop flushing.

Page 64: Chlorination / DeChlorination Procedures - PNWS-AWWA

Required Equipment

• Proper dechlorination device that will neutralize the chlorine residual.

• The proper amount of dechlorination chemical.

• Proper chlorine test equipment that will measure to 0.01 mg/l this means TEN PARTS PER BILLION.

Page 65: Chlorination / DeChlorination Procedures - PNWS-AWWA

Set-up Discharge area

• You will need to discharge water from the system during the flushing operation.

• Make sure that the area will handle the amount of the discharge.

• Store chemicals properly.• Set-up additional

monitoringequipment.

Page 66: Chlorination / DeChlorination Procedures - PNWS-AWWA

Set-up• Determine where the device will be located in

relationship to the discharge point from the outlet of the system.

• It is preferred to have the discharge point away from the device.

Page 67: Chlorination / DeChlorination Procedures - PNWS-AWWA

Set-up

• Testing for chlorine…

Page 68: Chlorination / DeChlorination Procedures - PNWS-AWWA

Testing your discharge

• If your test shows no chlorine, turn feed solution control valve down until you show a sign of chlorine in your discharge.

• Then open feed solution control valve a slight amount to balance feed solution strength to chlorine residual discharge.

• As you are flushing you may test your incoming residual level of chlorine by drawing a sample from the make-up water valve.

Page 69: Chlorination / DeChlorination Procedures - PNWS-AWWA

Always Dechlorinate when discharging chlorinated water…

Page 70: Chlorination / DeChlorination Procedures - PNWS-AWWA

For more information:Measurement Technologies, Inc.

P.O. Box 2195Redmond, WA 98073-2195

877-889-VITC (8482)425.836.8683

E-Fax: 425.484.6664www. H2ONeutralizer.com

© 2009