Cannondale Pull Shock Setup Guide
2
NEGATIVE AIR VALVE MAX PRESSURE: 175 PSI, 12 BAR POSITIVE AIR VALVE MAX PRESSURE: 475 PSI, 33 BAR REDBOUND DIAL DAMPING REMOTE FRONT OF BIKE SHOCK MOUNTING BOLTS 8.0 Nm (71 InLbs) Loctite 242 (Blue) REMOTE CABLE 1MP01/SLV 129338 XFUSION PULL SHOCK SET-UP INFORMATION - 10/12 OWNER’S MANUAL SUPPLEMENT 10/12 XFUSION PULL SHOCK SET-UP INFORMATION About this Supplement This supplement includes information for the proper installation and set up of XFUSION shocks in the following Cannondale models: Trigger 29’er Alloy, Trigger 26 Carbon, and both Jekyll and Scarlet. In addition to this supplement, follow the owner’s manual supplement information for your specific bike and the XFUSION owner’s manual. Cannondale supplements : http://www.cannondale.com/manuals/ XFUSION manuals: http://www.xfusionshox.com/ Mounting the Shock in the Frame Install the shock in the frame with the remote assembly facing forward as shown. Apply Loctite 242 (blue) and tighten with a good torque wrench. NOTICE: Incorrect shock installation can result in serious frame damage. Measuring Sag Some bike models have sag indicators integrated with the frame shock link; see your owner’s supplement. Sag can be measured by the difference between the shock mounting bolts when rider is on and off the bike. The recommended air pressure setting for the different models are shown on page 2. Use a high-pressure pump: Cannondale 1MP01/SLV. Press the small top button to release the lever. When the remote lever is UP, the shock is OPEN. Press the remote lever down until it locks to change the shock to FIRM. PAGE 1 OF 2 Handlebar Remote The handlebar remote changes the shock performance between “OPEN” and “FIRM.” See the illustrations below.
Transcript of Cannondale Pull Shock Setup Guide
Page 1 of 4
NEGATIVE AIR VALVE
MAX PRESSURE: 175 PSI, 12 BAR
POSITIVE AIR VALVE
MAX PRESSURE: 475 PSI, 33 BAR
REDBOUND DIAL
DAMPING REMOTE
FRONT OF BIKE
SHOCK MOUNTING BOLTS8.0 Nm (71 InLbs)Loctite 242 (Blue)
REMOTE CABLE
1MP01/SLV
129338 XFUSION PULL SHOCK SET-UP INFORMATION - 10/12
OWNER’S MANUAL SUPPLEMENT 10/12
XFUSION PULL SHOCK SET-UP INFORMATION
About this SupplementThis supplement includes information for the proper installation and set up of XFUSION shocks in the following Cannondale models: Trigger 29’er Alloy, Trigger 26 Carbon, and both Jekyll and Scarlet. In addition to this supplement, follow the owner’s manual supplement information for your specific bike and the XFUSION owner’s manual.
Cannondale supplements : http://www.cannondale.com/manuals/
XFUSION manuals: http://www.xfusionshox.com/
Mounting the Shock in the FrameInstall the shock in the frame with the remote assembly facing forward as shown. Apply Loctite 242 (blue) and tighten with a good torque wrench. NOTICE: Incorrect shock installation can result in serious frame damage.
Measuring SagSome bike models have sag indicators integrated with the frame shock link; see your owner’s supplement. Sag can be measured by the difference between the shock mounting bolts when rider is on and off the bike. The recommended air pressure setting for the different models are shown on page 2. Use a high-pressure pump: Cannondale 1MP01/SLV.
Press the small top button to release the lever. When the remote lever is UP, the shock is OPEN.
Press the remote lever down until it locks to change the shock to FIRM.
PAGE 1 OF 2
Handlebar RemoteThe handlebar remote changes the shock performance between “OPEN” and “FIRM.” See the illustrations below.
TRIGGER 29’ER ALLOY
RECOMMENDED SAG: 25% (32mm)Use the table below to set intial air pressure(s) according to rider weight; measure sag, then add or release air pressure in small amounts to set sag.
XFUSION SHOCK INFO:CANNONDALE P/N TRAVEL EYE-TO-EYE BUSHING WIDTH
128870 130mm 155 x 50mm 22 mm
RECOMMENDED AIR PRESSURE:
RIDER WEIGHT (LBS)
POSITIVE (PSI)
NEGATIVE (PSI)
POSITIVE (BAR)
NEGATIVE (BAR)
Under 100 158 61 11.0 4.0
100 - 109 169 65 11.6 4.5
110 - 119 179 69 12.4 4.8
120 - 129 191 73 13.2 5.1
130 - 139 203 78 14.0 5.4
140 - 149 216 83 14.9 5.7
150 - 159 230 88 15.8 6.1
160 - 169 244 94 16.9 6.5
170 - 179 260 100 17.9 6.9
180 - 189 273 105 18.8 7.2
190 - 199 287 110 19.8 7.6
200 - 209 301 116 20.8 8.0
210 - 219 316 122 21.8 8.4
220 - 229 332 128 22.9 8.8
230 - 239 348 134 24.0 9.2
240 - 249 366 141 25.2 9.7
TRIGGER 26 CARBON
RECOMMENDED SAG: 25% (30mm)Use the table below to set intial air pressure(s) according to rider weight; measure sag, then add or release air pressure in small amounts to set sag.
XFUSION SHOCK INFO:CANNONDALE P/N TRAVEL EYE-TO-EYE BUSHING WIDTH
128410 120mm 145 x 40mm 15.75mm
RECOMMENDED AIR PRESSURE:
RIDER WEIGHT (LBS)
POSITIVE (PSI)
NEGATIVE (PSI)
POSITIVE (BAR)
NEGATIVE (BAR)
Under 100 183 56 12.6 3.9
100 - 109 195 60 13.4 4.1
110 - 119 207 63 14.3 4.4
120 - 129 220 68 15.2 4.7
130 - 139 234 72 16.2 5.0
140 - 149 249 76 17.2 5.3
150 - 159 265 81 18.3 5.6
160 - 169 282 86 19.4 6.0
170 - 179 300 92 20.7 6.3
180 - 189 315 97 21.7 6.7
190 - 199 331 101 22.8 7.0
200 - 209 347 107 24.0 7.3
210 - 219 365 112 25.1 7.7
220 - 229 383 117 26.4 8.1
230 - 239 402 123 27.7 8.5
240 - 249 422 129 29.1 8.9
JEKYLL / SCARLETT
RECOMMENDED SAG: 30% (45mm)Use the table below to set intial air pressure(s) according to rider weight; measure sag, then add or release air pressure in small amounts to set sag.
XFUSION SHOCK INFO:CANNONDALE P/N TRAVEL EYE-TO-EYE BUSHING WIDTH
128761 150mm 155 x 50mm 15.75mm
RECOMMENDED AIR PRESSURE:
RIDER WEIGHT (LBS)
POSITIVE (PSI)
NEGATIVE (PSI)
POSITIVE (BAR)
NEGATIVE (BAR)
Under 100 183 53 12.6 3.7
100 - 109 195 56 13.4 3.9
110 - 119 207 60 14.3 4.1
120 - 129 220 64 15.2 4.4
130 - 139 234 68 16.2 4.7
140 - 149 249 72 17.2 5.0
150 - 159 265 77 18.3 5.3
160 - 169 282 82 19.4 5.6
170 - 179 300 87 20.7 6.0
180 - 189 315 91 21.7 6.3
190 - 199 331 96 22.8 6.6
200 - 209 347 101 24.0 6.9
210 - 219 365 106 25.1 7.3
220 - 229 383 111 26.4 7.7
230 - 239 402 117 27.7 8.0
240 - 249 422 122 29.1 8.4
129338 XFUSION PULL SHOCK SET-UP INFORMATION - 10/12
PAGE 2 OF 2
