KEY FEATURES

+ Rotating spray

+ 360° cleaning pattern

+ Ideal for small to medium-sized tanks

+ Low pressure

+ Low use of cleaning medium

Bio 7SBScanjet tank cleaning equipment

The Scanjet Bio 7SB is a new type of Rotary Spray Head (RSH) tank cleaning

device. Compared with conventional static devices, the Bio 7SB is very efficient,

saving water and chemicals while improving cleaning effectiveness. The Bio 7SB

employs a unique fluid bearing rotary mechanism, with a service life two to three

times that of traditional ball bearing rotary devices.

The choice of either a clip-on (pin), weld-on or threaded connection means the Bio

7SB is always easy to install, whether building a new CIP tank cleaning system or

upgrading an existing one based on ordinary static or rotary spray devices.

With 360° impact coverage, self-cleaning and self-draining features, the Bio 7SB

design follows EHEDG and GMP guidelines, and can be supplied with EN10204-

2.1, 2.2 or 3.1 material and FDA 21CFR compliance certificates. The Bio 7SB-XXX-A

clip-on and weld-on versions have attained 3A certification under sanitary standard

78-01. Surface finish roughness supplied as standard is Ra = 0.8 μm (30 μ inch);

other surfaces are available upon request.

The Bio 7SB can be used in conjunction with the Scanjet WASHTRAC sensor to

monitor and verify its operation and performance.

The Bio 7SB is the first choice for anyone looking for the most advanced Rotary

Spray Head tank cleaning device available.

The Scanjet Bio 7SB Rotary Spray Head can be used in a wide range of

applications, including:

+ Mixing vessels

+ Blending tanks

+ Beverage tanks

+ Dairy tanks

+ Yeast tanks

+ Reactors

+ IBCs

1 1,5 2 2,5 3 3,5 4 4,5 5

0

4

8

12

16

20

24

28

20 30 40 50 60 70

0

40

80

120

20

60

100

m3/h USgpm

psi

bar

1 1,5 2 2,5 3 3,5 4 4,5 5

0

1

2

3

4

0,5

1,5

2,5

3,5

20 30 40 50 60 70

0

1

2

3

4

5

6

7

8

9

10

11

12

13

m ft

bar

psi

Wetting

Impact cleaning

360º SPRAY PATTERN

1¼" BSPf1¼" NPTf

THREADCONNECTION

Ø 38/35.6(ID) (1.5/1.4 in)

115

(4.5

3 in

)

Ø 65 (2.56 in)

WELDCONNECTION

Ø 38.4/41.6(OD) (1.51/1.64 in)Ø 38.3/41.4(OD) (1.5/1.63 in)

PINCONNECTION

¾" BSP¾" NPT

THREADCONNECTION

25/22,5(OD)

45

75

WELDCONNECTION

25,6/ 28,6(ID/OD)25,3/28,3(ID/OD)

PINCONNECTION

360º SPRAY PATTERN

*Because of variations in part wear, water temperature, installation etc., the flow may differ ±10% from specified value.Continuous product improvement is the policy of Scanjet Group and we reserve the right to alter the specifications at any time without prior notice. Errors and omissions excepted.All trademarks, designs and other intellectual property depicted here are property of the Scanjet Group unless otherwise stated, and may be registered, patented or otherwise protected in certain jurisdictions.Copyright © Scanjet Group. All rights reserved.

Technical performance Dimensions

Specifications

Flow* 10.7-27.5 m³/h (47-120 USgpm)

Inlet pressure 1-5 bar (14-72 psi)

Max pressure 5 bar (72 psi)

Recommended pressure 3 bar (43 psi)

Max working temperature 95°C (200°F)

Max ambient temperature 150°C (300°F)

Weight 452-477 g (15.94-16.83 oz)

Connections Weld connection

Pin connection

1¼” BSPf / 1 ¼” NPTf

Material EN1.4404/PEEK

Lubrication Self lubricated by media

Pressure/Flow

Cleaning radius

Scanjet Systems AB P.O. Box 9316 SE-400 97 Göteborg SwedenPhone + 46 31 3387530 Fax + 46 31 3387540 E-mail sales@scanjetsystems.comWeb www.scanjetsystems.com

* Clip-on models have approx. 0,5 m³/h higher flow rate