Battery Shelf Kit Manual
10
SiteTel Sweden AB Box 7039 Staffans Väg 4-8 SE-192 07 Sollentuna Sweden Ph: +46 (0)8 410 102 00 Fax: +46 (0)8 638 06 00 [email protected] SiteStar Battery Shelf CPI Document No: D000101 Revision: R1A
description
Battery_shelf_kit_manual
Transcript of Battery Shelf Kit Manual
-
SiteTel Sweden AB Box 7039 Staffans Vg 4-8 SE-192 07 Sollentuna Sweden Ph: +46 (0)8 410 102 00 Fax: +46 (0)8 638 06 00 [email protected]
SiteStar Battery Shelf CPI
Document No: D000101
Revision: R1A
-
Document No: D000101-INS-01 Page 2 of 10
Revision: PA5
Contents
1 Battery Shelf ......................................................................................................................... 3
1.1 Content of the packaging............................................................................................... 3
1.2 Tools ............................................................................................................................. 3
1.3 Assembling extra Shelves ............................................................................................. 3
1.3.1 Air separator .......................................................................................................... 3
1.4 Assembling shelves ....................................................................................................... 6
1.5 Reassembling the Air Separator .................................................................................... 8
-
Document No: D000101-INS-01 Page 3 of 10
Revision: PA5
1 BATTERY SHELF
1.1 CONTENT OF THE PACKAGING
Content of the packaging
Item No. Designation Art. No. Quantity
1 Manual D000101 1
2 Shelf kit D000114 1
3 Screw RXSF
DIN 968 Steel 4,2 x 13
12
1.2 TOOLS
The following tools are required for the battery shelf installation.
Screwdriver pozidrive pz#2
Universal pliers
1.3 ASSEMBLING EXTRA SHELVES
1.3.1 AIR SEPARATOR
Before assembling extra Shelves, the Air Separator (delivered with the cabinet) placed where the lower Shelf will be attached, has to be removed. Figure 01 - 02.
-
Document No: D000101-INS-01 Page 4 of 10
Revision: PA5
Figure 01
-
Document No: D000101-INS-01 Page 5 of 10
Revision: PA5
Figure 02
-
Document No: D000101-INS-01 Page 6 of 10
Revision: PA5
1.4 ASSEMBLING SHELVES
Push the extra Shelves into the Cabinet. The Shelves will fit into prefabricated holes in the Cabinet wall. Figure 03.
Figure 03
-
Document No: D000101-INS-01 Page 7 of 10
Revision: PA5
Use the 12 screws delivered with each Shelf, to assemble the Shelves to the Cabinet. Figure 04.
Tighten the Screws with an end torque of 1 Nm. Start torque is higher.
Figure 04
-
Document No: D000101-INS-01 Page 8 of 10
Revision: PA5
1.5 REASSEMBLING THE AIR SEPARATOR
When the lower shelf is attached, the air separator has to be reassembled at the front of the shelf. The air separator shall always be assembled at the lower shelf when extra shelves are assembled. Figure 07.
In case of cable routing at the front, the air separator has to be modified. The outer parts of the separator have to be folded or cut of to give space for the cables. Figure 05. If the cables are routed at the back of the cabinet the air separator can be left unfolded/uncut.
Figure 05
-
Document No: D000101-INS-01 Page 9 of 10
Revision: PA5
Reassembling the Air Separator. Figure 06 - 07.
Figure 06
-
Document No: D000101-INS-01 Page 10 of 10
Revision: PA5
Figure 07
