AVR ZIF Programmer - Weebly
5
PROVOTECH Sense. Innovate. Educate For technical enquiry please email us at [email protected] And for sales enquiry please email us at [email protected] and [email protected] AVR ZIF Programmer AVR ZIF Programmer is not a programmer per se but it’s an extension board for our USBASP Programmer using which one can program AVR’s 40 pin micro-controller (ATmega16, ATmega32); 28 pin micro-controller (ATmega8, ATmega32, etc…) along with AT89s51 / 52 micro-controller. Features: Operating Voltage: 5V DC (Powered using USB Programmer). Compatible for ATmega16, ATmega8, AT89s51 similar controllers. Easy interface due to 10 pin FRC Connector.
Transcript of AVR ZIF Programmer - Weebly
PROVOTECH Sense. Innovate. Educate
For technical enquiry please email us at [email protected] And for sales enquiry please email us at [email protected] and [email protected]
AVR ZIF Programmer
AVR ZIF Programmer is not a programmer per se but it’s an extension board
for our USBASP Programmer using which one can program AVR’s 40 pin
micro-controller (ATmega16, ATmega32); 28 pin micro-controller
(ATmega8, ATmega32, etc…) along with AT89s51 / 52 micro-controller.
Features: Operating Voltage: 5V DC (Powered using USB Programmer).
Compatible for ATmega16, ATmega8, AT89s51 similar controllers.
Easy interface due to 10 pin FRC Connector.
PROVOTECH Sense. Innovate. Educate
For technical enquiry please email us at [email protected] And for sales enquiry please email us at [email protected] and [email protected]
Using the module for AVR Series Microcontroller:
To program ATMEL micro-controllers for AVR series one has to use the ZIF
Connector provided on the board. The following diagram shows how to place
coressponding micro-controller onto the board.
PROVOTECH Sense. Innovate. Educate
For technical enquiry please email us at [email protected] And for sales enquiry please email us at [email protected] and [email protected]
Using the module for AVR ATmega8 / 328 (28 Pin ICs):
While using this board to program 28 pin IC like ATmega8 /
328, place the IC in the middle of the ZIF connector leaving 3
spaces at the top and 3 spaces at the bottom. Also the IC notch
should face downwards as shown in picture below.
Keep in mind the jumper should not be shorted.
Ideally use software like WinAVR since it is both a code complier and
hex burner.
PROVOTECH Sense. Innovate. Educate
For technical enquiry please email us at [email protected] And for sales enquiry please email us at [email protected] and [email protected]
Using the module for AVR ATmega16 / 32 (40 Pin ICs):
While using this board to program 40 pin IC like ATmega16 /
32, place the IC notch facing upwards as shown in picture
below.
Keep in mind the jumper should be shorted to program 40 Pin micro-
controller.
Ideally use software like WinAVR since it is both a code complier and
hex burner.
PROVOTECH Sense. Innovate. Educate
For technical enquiry please email us at [email protected] And for sales enquiry please email us at [email protected] and [email protected]
Using the module for ATMELs AT89S51 / 52:
To program ATMEL micro-controllers for AT89S51 series one
has to use the 40 Pin IC base provided on the board.
While using this board to program 40 pin IC like AT89S51 /
52, place the IC notch facing upwards as shown in picture
below.
Keep in mind the jumper should not be shorted to program 40 Pin
micro-controller.
Ideally use software like Keil as a code complier and ProgISP as a hex
burner.
Note that while programming AT89S51 / 52 one might need to press
reset button till the process is complete.
