ansys lab manual.doc
-
Upload
sharma-kripa -
Category
Documents
-
view
113 -
download
3
description
Transcript of ansys lab manual.doc
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
BTech IV year -1st sem as per JNTU ANANTAPUR
CAD/CAM LAB MANUAL
Prepared by
M SIVARAMAKRISHANIAH
M.Tech(PhD)
Page 1
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
INDEXEXP.NO DATE TOPIC PAGE.NO
AUTO CAD 03
1. 2D SKETCH 1 04-05
2. 2D SKETCH 2 06-07
3. 2D SKETCH 3 08
PART MODELING(SOLID WORKS) 09
INTRODUCTION 10-12
1. CAMERA BODY 13-17
2. AUTOMOBILE WHEEL 18-23
3. ROPE 24-27
ANSYS-14 28
INTRODUCTION 29-30
1. STEPPED BAR(TAPER BAR) 31-36
2. TRUSS 37-42
3. NATURAL FRQUENCY 43-49
4. WALLS 50-57
CAM 58
INTRODUCTION 59-63
1. FACING CYCLE 64-65
2. TURNING CYCLE 66-67
3. LINEAR & CIRCULAR INTERPOLATION(MILLING)
68-69
4. CFD NOZZLE 71-84
Page 2
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Auto CAD
Page 3
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
1. SKETCH-1
Aim: To develop a 2D –model of given figure as per the given dimentions.
Apparatus: Windows operating system, CAD 2010 Software ,600 x 450 pixels Graphics
system, plotters.
Program:
1. Command: Rectangle
Specify first corner point or (chamfer/elevation/fillet/thickness/width)
Specify other corner point or (Dimensions) :@550,400
2. Command: Explode:
Selected objects : 1
3. Command: Chamfer:
Select first line or (polyline/distance) : d
(Angle/trim/method)
Specify first chamfer distance : 125 mm
Specify second chamfer distance : 200 mm
Select first line or (polyline/distance/Angle/trim/method): Select second line.
4. Command: Circle
Page 4
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Specify center point for circle: (3p/2p/ttr (tan tan radius)
Specify radius of circle or (Diameter) : 50 mm
Specify center point for circle or (3p/2p/ttr (tan tan radius) :
Specify radius of circle or (Diameter) :100 mm
5. Command: Circle
Specify center point for circle or(3p/2p/ttr(tan tan radius)
Specify radius of circle or Diameter : 50mm
6.Command: Dimension
Marking all the dimensions as per the given dimensions.
Result: The 2D model is obtained as per the given Dimensions.
Page 5
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
2. SKETCH-2 3.
Aim: To develop a 2D model of given figure as per the given dimensions.
Apparatus: windows operating system.CAD 2010 SOFTWARE, 200 X 190 Graphics system, plotter
Program:
1. Command: RectangleSpecify first corner point or (chamfer/elevation/fi;;et/thickness/width):Specify other corner point or: @150, 92.5.2. Command: ExplodeSelect objects : 13. Command: ChamferSelect objects: 14. Command: chamferSelect first line or (polyline/distance/angle/trim/method) :dSpecify first chamfer distance: 25mmSpecify second chamfer distance : 25Select first line or (polyline /distance/angle/trim/method):Select second line:5. Command: chamfer
Select first line or(Poly line/distance/angle/trim/method) :dSpecify first chamfer distance: 25Specify second chamfer distance :25Select first line or (polyline/distance/angle/trim/method):Select second line:
6. Command: lineSpecify first pointSpecify next point or (undo):@7.5<270Specify next point or (undo) @50<180Specify next point or (undo)@10<90Specify next point or (undo)@70<180Specify next point or (undo) 35<2707. Command: Chamfer Select first line or (polyline/distance/angle/trim/method) :dSpecify first chamfer distance: 12.5
Page 6
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Specify second chamfer distance: 12.5Select first line or(Polyline/distance/angle/trim/method):Select second line:8. Command: Mirror Select objectsSpecify first point of mirror line:Specify second point of mirror line:Delete source objects?(yes/no) :n9. Command: Dimension
Marking all the dimensions of the figure by using dimension commands.
Results: The 2D model is obtained as per the given dimensions.
Page 7
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
3. SKETCH-3
Aim: To develop a 2Dmodel of given figure as per the given dimensions
Apparatus: Windows operating system, CAD2002 software, 350*250graphics system Plotter
Program: 1) Command: rectangleSpecify first corner point or [chamfer/elevation/fillet/thickness/width]:Specify other point or[Dimensions] :@300,2002) Command: chamferSelect first line or [Poly line / distance / angle /trim/ method]: dSpecify first chamfer distance: 75Specify second chamfer distance: 50Select first line or [Poly line / distance / angle/ trim/method]:Select second line:4) Command: chamfer Select first line or [Poly line / distance / angle / trim / method]:Specify first chamfer distance: 125Specify first line or [Poly line / distance / angle / trim / method]:Select second line 5) Command: lineSpecify first point :Specify next point or [undo]: @25< 900
Specify next point or [undo]: @75<00
Specify next point or [undo]: @50<900
Specify next point or [undo]: @50<900
6) Command: dimension Making all the dimensions as per the figure by using aligned command Result The 2D model is obtained as per the given dimensions
Page 8
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Part Modeling
Solid Works
Page 9
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Basics of Solids Modeling with Solid Works
Introduction Solid Works is the state of the art in computer-aided design (CAD). Solid Works
represents an object in a virtual environment just as it exists in reality, i.e., having volume as well as surfaces and edges. This, along with exceptional ease of use, makes Solid Works a powerful design tool. Complex three-dimensional parts with contoured surfaces and detailed features can be modeled quickly and easily with Solid-Works. Then, many parts can be assembled in a virtual environment to create a computer model of the finished product. In addition, traditional engineering drawings can be easily extracted from the solids models of both the parts and the final assembly. This approach opens the door to innovative design concepts, speeds product development, and minimizes design errors. The result is the ability to bring high-quality products to market very quickly.
CONSTRAINT-BASED SOLIDS MODELING The constraint-based solids modeling used in Solid Works makes the modeling
process intuitive. The 3-D modeling begins with the creation of a 2-D sketch of the profile for the cross section of the part. The sketch of the cross section begins much like the freehand sketch of the face of an object. The initial sketch need not be particularly accurate; it needs only to reflect the basic geometry of the part’s cross-sectional shape. Details of the cross section are added later. The next step is to constrain the two-dimensional sketch by adding enough dimensions and parameters to completely define the shape and size of the two-dimensional profile. The name constraint-based modeling arises because the shape of the initial two-dimensional sketch is “constrained” by adding dimensions to the sketch. Finally, a three-dimensional object is created by revolving or extruding the two-dimensional sketched profile. Figure 1 shows the result of revolving a simple L-shaped cross section by 270o about an axis and extruding the same L-shaped cross section along an axis.
In either case, these solid bodies form the basic geometric solid shapes of the part. Other features can be added subsequently to modify the basic solid shape. Once the solids model is generated using Solid Works, all of the surfaces have been automatically defined, so it is possible to shade it in order to create a photorealistic appearance. It is also easy to generate two-dimensional orthographic views of the object. Solid modeling
Page 10
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
is like the sculpting of a virtual solid volume of material. Because the volume of the object is properly represented in a solids model, it is possible to slice through the object and show a view of the object that displays the interior detail (sectional views). Once several solid objects have been created, they can be assembled in a virtual environment to confirm their fit and to visualize the assembled product. Solids models are useful for purposes other than visualization. The solids model contains a complete mathematical representation of the object, inside and out. This mathematical representation is easily converted into specialized computer code that can be used for stress analysis, heat transfer analysis, fluid-flow analysis, and computer-aided manufacturing. Getting Started in Solid Works, Introduction and Reference Solid Works Corporation developed Solid Works® as a three-dimensional, feature-based, solids-modeling system for personal computers.
Solid modeling represents objects in a computer as volumes, rather than just as collections of edges and surfaces. Features are three-dimensional geometries with direct analogies to shapes that can be machined or manufactured, such as holes or rounds. Feature-based solid modeling creates and modifies the geometric shapes of an object in a way that represents common manufacturing processes. This makes Solid Works a very powerful and effective tool for engineering design. As compared with other computer programs, Solid Works organizes and stores data in files. Each file has a name followed by a period (dot) and an extension. There are several file types used in Solid Works, but the most common file types and their extensions are
Part files .prt or .sldprtAssembly files .asm or .sldasmDrawing files .drw or .slddrw
Part files are the files of the individual parts that are modeled. Part files contain all of the pertinent information about the part. Because Solid Works is a solids-modeling program, the virtual part on the screen will look very similar to the actual manufacture part. Assembly files are created from several individual part files that are virtually assembled (in the computer) to create the finished product. Awing files are the two dimensional engineering drawing representations of both the part and assembly file. The drawings should contain all of the necessary information for the manufacture of the part, including dimensions, part tolerances, and so on. The part file is the driving file for all other file types. The modeling procedure begins with part files. Subsequent assemblies and drawings are based on the original part files. One advantage of Solid Works files is the feature of dynamic links. Any change to a part file will automatically be updated in any corresponding assembly or drawing file.
Tool bars:• The Sketch toolbar contains tools to set up and manipulate a sketch.
Page 11
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
• The Sketch Tools toolbar contains tools to draw lines, circles, rectangles, arcs, and so on.
• The Sketch Relations toolbar contains tools for constraining elements of a sketch by using dimensions or relations.
• The Features toolbar contains tools that modify sketches and existing features of a part.
• The Standard toolbar contains the usual commands available for manipulating files (Open, Save, Print, and so on), editing documents (Cut, Copy, and Paste), and accessing Help.
• The Standard Views toolbar contains common orientations for a model. • The View toolbar contains tools to orient and rescale the view of a part.
• Line: creates a straight line. • Center point Arc: creates a circular arc from a center point, a start point, and an
end point. • Tangent Arc: creates a circular arc tangent to an existing sketch entity. • 3 Pt Arc: creates a circular arc through three points. • Circle: creates a circle. • Spline: creates a curved line that is not a circular arc. • Polygon: creates a regular polygon. • Rectangle: creates a rectangle. • Point creates: a reference point that is used for constructing other sketch entities. • Centerline: creates a reference line that is used for constructing other sketch
entities. • Convert Entities: creates a sketch entity by projecting an edge, curve, or contour
onto the sketch plane. • Mirror: reflects entities about a centerline. • Fillet: creates a tangent arc between two sketch entities by rounding an inside or
an outside corner. • Offset: Entities creates a sketch curve that is offset from a selected sketch entity
by a specified distance. • Trim: removes a portion of a line or curve. • Construction Geometry: creates entities that aid in sketching. • Linear Sketch Step and Repeat: creates a linear pattern of sketch entities.• Circular Sketch Step and Repeat: creates a circular pattern of sketch entities.
Page 12
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
1.Camera BodyAIM: To model the given object using the Extrusion feature as per the dimensions given.
Description of Extrusion Future:
Base Feature:The first feature to be created.The foundation of the part.The base feature geometry for the box is an extrusion.
To create an Extruded Base Feature:
1. Select a sketch plane.
Sketch a 2D profile of the square model as shown in the figureSelect front plane Right click select insert sketchSketch a 2D profile of the square model Give the dimension and it should come fully define Ok exit sketch
Page 13
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
2. Extrude the sketch perpendicular to sketch plane(Select Insert Boss/Bass Extrude) ok
3. Draw a circle of Diameter 50 mm, Select front plane to draw the 2D circle of dia 50 > Give the dimension and it should come fully define > Ok exit sketchIt adds material to the part and requires a sketch.
Page 14
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
6. Extrude the sketch perpendicular to sketch planeSelect the sketch and then ( select Insert Boss/Bass Extrudeok
4. Draw the circle for the Diameter of 35 mm and Select front plane to draw the 2D circle of dia 35 > Give the dimension it should come fully define > Ok > exit sketch(Select Insert cut Extruded)Feature:
It Removes material from the part and also it requires a sketch.
Page 15
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
5. Fillet Feature:Round the edges of faces of a part to a specified radius.(SelectinsertFeaturefillet)
Page 16
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Procedure:1. Select a sketch plane (Front, top or side)2. Sketch a 2D profile of the model.3. Dimension the model using smart Dimensions icon.4. Check the sketch is fully defined5. Extrude the sketch perpendicular to sketch plane.6. Use extrude cut feature to cut the solid as given in the drawing.
Result:Thus the given model is extruded.
Page 17
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
2. Automobile WheelAIM: To model the given object using the Revolve and circular pattern feature as per the dimensions given.
1. Create a 2D sketch on Front Plane as shown in the figure.(Right click the Front plane>insert sketch and draw the 2D sketch)
Note: All the 2D sketches drawn should be fully Defined and there should not be any under defined)and use ( click Add Relation and Smart Dimensions)
Page 18
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
1. Revolve, the sketch to 360 degree on top sketched line, by (Insert> Boss/Base>Revolve) ok.
2. Create circle of 2D sketch of Diameter of 121.92 mm, on right plane and extrude to 50.8mm
(Select the face by (Enter Space bar> double click the Normal plane)
and Draw the 2D sketch as given above
Extrude by (Insert>Boss/Base>Extrude)) ok.
3. Draw the sketch on edge wheel face, sketch for arm hole ,
Page 19
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Select the face by (Enter Space bar> double click the Normal plane)
and Draw the 2D sketch as given below
4. And remove the material by (Insert>cut>Extrude), through all, OK.
Page 20
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
5. Add fillet R12.7mm inner(Insert>Features>Fillet/Round),add fillet 5.08mm for corner ok
Page 21
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
6. Click Circular Pattern ,click (View>Temporary Axes,) select center axis as rotation axis
8.( Give 360 degree and 5 equal spacing) , Select Cut-Extrude1, Fillet1 and Fillet2 as a Features to Pattern. OK.
7. Click on hub face, insert sketch, sketch center circle diameter 69.85mm. Extrude Cut to 12.7mm deep.(Insert>cut>Extrude).
Page 22
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
8. Add chamfer 12.7mm to inner cut and add chamfer 6.35mm to wheel edge ok done. .(Insert>Feature>chamfer).
Result:Thus the given model is completed.
Page 23
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
3. Three layer Rope
AIM: To model the given object using the Sweep and circular step and repeat feature as per the dimensions given.
1. Create a spline curve sketch on Front Plane.
(Front planeInsert SketchDraw the spline using spline tool bar right clickend spline)
( select close dialog box andexit sketch.)
2.and another spline curve sketch on top plane
(select Top planeInsert Sketchclick Space bar and double click the Normal plane Draw the spline using spline tool barright clickend spline)
Page 24
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
( select close dialog box andexit sketch.)
3.create 3D plane curve
(using, insert curveprojected, select Two (cures)sketches ,
when we rotate the geometry it will show 3D curve. Click OK.
4.at one end of the 3D curve, create new plane.
(InsertReference Geometryplane),select curve end point and edge curve and OK.
5.create a circle with suitable dimensions, nearby end of the spline curve.
Page 25
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
6.Before finishing sketch(select Toolssketch toolscircular step and repeat) from that given number of rope layers.( 3 or 4). OK and select finish sketch.
7.Take sweep (insertboss/base sweep) command and give
select profile and there relative circle, and
select path there relative curve,
optionsorientation /twist type(select along path),
Define byselect turns give the valve of 50 to 100). ok done.
Page 26
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Result:Thus the given model is completed.
Page 27
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
ANSYS -14
Page 28
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
The Purpose of FEAAnalytical Solution• Stress analysis for trusses, beams, and other simple structures are carried out based on dramatic simplification and idealization:– mass concentrated at the center of gravity– beam simplified as a line segment (same cross-section)• Design is based on the calculation results of the idealized structure & a large safety factor (1.5-3) given by experience.FEA• Design geometry is a lot more complex; and the accuracy requirement is a lot higher. We need– To understand the physical behaviors of a complex object (strength, heat transfer capability, fluid flow, etc.)– To predict the performance and behavior of the design to calculate the safety margin; and to identify the weakness of the design accurately; and– To identify the optimal design with confidence.Brief History1. Grew out of aerospace industry2. Post-WW II jets, missiles, space flight3. Need for light weight structures4. Required accurate stress analysis5. Paralleled growth of computers.Common FEA ApplicationsMechanical/Aerospace/Civil/Automotive EngineeringStructural/Stress Analysis Static/Dynamic Linear/NonlinearFluid FlowHeat TransferElectromagnetic FieldsSoil MechanicsAcousticsBiomechanics
Page 29
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
A GENERAL PROCEDURE FOR FINITE ELEMENT ANALYSIS
• Preprocessing– Define the geometric domain of the problem.– Define the element type(s) to be used (Chapter 6).– Define the material properties of the elements.– Define the geometric properties of the elements (length, area, and the like). – Define the element connectivities (mesh the model). – Define the physical constraints (boundary conditions). Define the loadings.• Solution– computes the unknown values of the primary field variable(s)– computed values are then used by back substitution to compute additional, derived variables, such as reaction forces, element stresses, and heat flow.• Post processing– Postprocessor software contains sophisticated routines used for sorting, printing, and plotting –Selected results from a finite element solution.Beam ElementThe usual assumptions of elementary beam theory are applicable here:1. The beam is loaded only in the y direction.2. Deflections of the beam are small in comparison to the characteristic dimensions of the beam. 3. The material of the beam is linearly elastic, isotropic, and homogeneous. The beam is prismatic and the cross section has an axis of symmetry in the plane of bending
Page 30
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
1. STEPPED BAR
AIM: For stepped bar to find the nodal displacement, stress in each element at the fixed end.A1 = 200 mm^2, A 2 = 100 mm^2 and E1 = E2 = 200GPa.
PREPROCESSING1.Main Menu > Preprocessor> Element Type > Add/Edit/Delete >Add >Structural Link > 3D finit stn 180> OK>Close.
Page 31
200 mm 100 mm
500 N1000 N
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
2.Main Menu >Preprocessor > real Constants >Add/Edit/Delete >Add >OK
Cross-Sectional area AREA > Enter 200 >Add >OK
Cross-sectional area AREA >Enter 100 >OK >Close.
3. Main Menu >Preprocessor >Material Props >Material Models
Page 32
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Material Model Number 1,click Structural >Linear >Elastic >Isotropic
Enter EX = 200E3 and PRXY = 0.3 >OK(Close the Define Material Model Behavior window.)Create the Nodes and elements. As it is stated in the problem that uses 2 element model Hence create 3 nodes and 2 elements.
4. Main MENU >Preprocessor > Modeling >Create > Nodes >In Active CS Enter the coordinates of node 3>OK.
5. Main Menu >Preprocessor >Modeling > Create >Elements > Elem Attributes > OK >Auto Numbered > Thru nodes Pick The 1st and 2nd node >OK.
Page 33
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Elem Attributes >change the Real content set number to 2 >OK>Auto Numbered >thru nodes Pick the 2nd and 3rd node >OK.
Page 34
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
6.Main Menu >Preprocessor >loads >Define Loads >Apply >Structural >Displacement >On Nodes Pick the 1st node >Apply >All DOF = 0 >OK.
7. Main Menu >Preprocessor >loads >Define Loads >Apply >Structural >Force/Moment >On nodes Pick the 3rd Node >Ok >Force/Moment value = 500 in FX direction >OK>Force/Moment >On Nodes pick the 2nd node >OK >Force/Moment value = -1000 in FX direction.The model-building step is now complete, and we can process to the solution. First to be safe, save the model.Solution. The interactive solution proceeds.
8.Main MENU >Solution >Solve >Current LS >OKThe/STATUS Command window displays the problem parameters and the Solve Current Load Step window is shown. Check the solution options in the/STATUS window and if all is OK,select File >Close.In the Solve Current Load Step window, Select OK, and when the solution is complete, close the Solution is Done! Window.
POSTPROCESSINGWe can now plot the results of this analysis and also list the computed values.
9. Main Menu>General postproc >Plot Results >Contour Plot >Nodal Solu >DOF >Solution >Displacement vector sum >OK.
Page 35
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
10.Main Menu >General Postproc >Element Table >Define Table >ADD Select Bysequence num and LS and type 1 after LS as shown in fig. >OK
11.Main Menu >General Post Proc >Plot Results >Contour Plot >Elem Table >Select LS1 >OK
Result: Thus the given model is simulated and verified stress and deflection.
Page 36
Stress pattern for stepped bar
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
2. TRUSS
AIM: Determine the nodal displacements, element stresses and support reactions for the three members truss A = 800 mm^2 and E = 200GPa for all members.
PREPROCESSING1. Main Menu > Preprocessor> Element Type > Add/Edit/Delete >Add >Structural
Link > 3D finit stn 180> OK>Close.
2. Main Menu >Preprocessor > real Constants >Add/Edit/Delete >Add >OK
Page 37
2 m 2 m
1.5 m
12 KN
8 KN
ө
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Cross-Sectional area AREA > Enter 200 >Add >OKCross-Sectional area AREA > Enter 200 >Add >OKCross-Sectional area AREA > Enter 200 >Add >OK
3. Main Menu >Preprocessor >Material Props >Material Models
Material Model Number 1,click Structural >Linear >Elastic >Isotropic
Enter EX = 200E3 and PRXY = 0.3 >OK(Close the Define Material Model Behavior window.)
Page 38
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Create the Nodes and elements. As it is stated in the problem that uses 2 element model hence create 3 nodes and 2 elements.
4. Main MENU >Preprocessor > Modeling >Create > Nodes >In Active CS Enter the coordinates of node 3>OK.
5. Main Menu >Preprocessor >Modeling > Create >Elements > Elem Attributes > OK >Auto Numbered > Thru nodes Pick The 1st and 2nd node >OK.
Elem Attributes >change the Real content set number to 2 >OK>Auto Numbered >thru nodes Pick the 2nd and 3rd node >OK.
Page 39
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
6. Main Menu >Preprocessor >loads >Define Loads >Apply >Structural >Displacement >On Nodes Pick the 1st node >Apply >All DOF = 0 >OK
7. Main Menu >Preprocessor >loads >Define Loads >Apply >Structural >Force/Moment > On nodes Pick the 2nd Node >Ok >Force/Moment value = 8000
Page 40
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
in FX direction >OK>Force/Moment >On Nodes pick the 2nd node >OK >Force/Moment value = -12000 in FY direction. Main Menu >Preprocessor >loads >Define Loads >Apply >Structural >Displacement >On Nodes Pick the 3rd node >Apply >FY = 0 >OK
The model-building step is now complete, and we can process to the solution. First to be safe, save the model.
Solution. The interactive solution proceeds.
8. Main MENU >Solution >Solve >Current LS >OKThe/STATUS Command window displays the problem parameters and the Solve Current Load Step window is shown. Check the solution options in the/STATUS window and if all is OK, select File >Close.In the Solve Current Load Step window, Select OK, and when the solution is complete, close the Solution is Done! Window.
POSTPROCESSINGWe can now plot the results of this analysis and also list the computed values.
9. Main Menu>General Postproc >Plot Results >Contour Plot >Nodal Solu >DOF >Solution >Displacement vector sum >OK.
10.Main Menu >General Postproc >Element Table >Define Table >ADD Select Bysequence num and LS and type 1 after LS as shown in fig. >OK.
Page 41
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
11. Main Menu >General Post Proc >Plot Results >Contour Plot >Elem Table >Select LS1 >OK.
Result: Thus the given model is simulated and verified stress and deflection.
Page 42
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
3. Natural Frequency of Cantilever Beam
AIM: To Determine the First Two Natural Frequencies.
Let E = 207 GPa, Poisson’s Ratio = 0.3, Length L= 2.5m,Cross sectional Area A= 1m^2,Mass Density ρ =7800 kg/m^3.
PREPROCESSING1.Main Menu > Preprocessor> Element Type > Add/Edit/Delete >Add >Structural Link > 3D finit stn 180> OK>Close.
2.Main Menu >Preprocessor > real Constants >Add/Edit/Delete >Add >OK
Page 43
2.5 m
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Cross sectional AREA >Enter 1 >OK>Close.Enter the Material Properties.3. Main Menu >Preprocessor >Material Props >Material Models
Material Model Number 1,click Structural >Linear >Elastic >Isotropic
Enter EX = 200E3 and PRXY = 0.3 >OKClick structural >Linear >Density =7800(Close the Define Material Model Behavior window.)Create the Key points and lines as shown in the figure.4. Main MENU >Preprocessor > Modeling >Create > Nodes >In Active CS Enter the coordinates of node 3>OK.
.
Page 44
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Key point locationsKey point number X coordinate Y coordinate
1 0 02 2.5 0
5.Main Menu >Preprocessor >Modeling >Create >Lines >Lines >Stright Line Pick the 1 st and 2 nd key point >OK.
Page 45
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
6.Main Menu >Preprocessor >Messing >Size Controls >Manual Size >Lines >All Lines >Enter NDIV No.of Element divisions =10.
7. Main Menu >preprocessor>Meshing>Mesh>Lines>Click Pick All
8. Main Menu >Solution>Analysis Type>New Analysis>Select Model>OK.
Page 46
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
9. Main Menu >Preprocessor>Loads >Apply>Structural >Displacement >On nodes Pick the Lest most node >Apply >Select All DOF>OK
Page 47
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
10. Main Menu>Solution >Analysis Type >Analysis options>Select Reduced option Enter No.of modes to extract =2
Enter FREQE Frequency range 0 -2500> OK.
Main Menu>Solution >Master DOFs>user selected >DEFINE >Pick all nodes except left most node>Ok >Select UX from Leb 1 1st DOF>OK.
Page 48
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Solution: The interactive solution proceeds.12. Main Menu>Solution >Solve >Current LS>okThe/STATUS Command window displays the problem parameters and the Solve Current Load Step window is shown. Click the solution options in the/STATUS window and if all is OK, select FILE >Close.In the solve, Current load step window, Select OK, and the solution is complete, Close the Solution is DONE, window.POSTPROCESSING13. Main Menu >General Postproc>Results SummaryThe result is shown as Frequency values in Hz14. Main Menu >General Postproc >Read Results >First Set15. Main Menu>General Postproc >Plot Results >Counter Plot>Nodal Solu>DOF.This result is shown in fig.
Result: Thus the given model is simulated and verified Natural Frequency at each node of elements.
Page 49
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
4. WALLS
AIM: To Determine the Temperature Distribution of combined plane walls.
PREPROCESSING1. Main Menu > Preprocessor> Element Type > Add/Edit/Delete >Add >Structural Link > 3D finit stn 180> OK>Close.
2. Main Menu>Preprocessor>Element Type>Add/Edit/Delete>Add>Click on Link>then on 3D conduction (Link 33)>OK>Add>Click on Link >then on 3D convection 34 >Ok>Close.
Page 50
h T∞
0.3m 0.15m 0.15m
K1 K2 K3
To
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Page 51
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
3. Main Menu>Preprocessor >Real Constants>Add/Edit/Delete>Add>Click on Link 32>Ok.Enter cross-sectional area AREA>Enter 1>OK
Add>Click on Link 34>OkEnter cross sectional area AREA>Enter 1>Ok>Close.
Enter the material properties.4. Main Menu >Preprocessor>Material props>Material ModelsMaterial Model Number 1,Click Thermal >Conductivity >IsotropicEnter KXX=30>ok
Page 52
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Then in the material model window click on Material menu >New model>OKMaterial Model Number 2,Click Thermal>Conductivity>isotropicEnter KXX=50>Ok
Then in the material Model window click on Material menu>New Model>OKMaterial Model Number 3,Click Thermal>Conductivity>IsotropicEnter KXX=20>ok.
Page 53
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Then in the material model window click on Material menu >New Model>OKMaterial Model Number 4,Click Thermal>Convection or film coef.Enter HF=25>ok
Page 54
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
(Close the Define Material Model Behavior window.)Create the nodes and elements.5. Main Menu>Preprocessor>Modeling>Create>Nodes>InActive CS Enter the coordinates of node1>Apply Enter the coordinates of node 2>Apply Enter the coordinates of node 3>Apply>Enter the coordinates of node 4>Apply Enter the coordinates of node 5>Ok6. Main Menu>Preprocessor>Modeling>Create >Elements>Elem Attributes>ok>Auto Numbered>Thru nodes Pick the 1 st and 2nd node>Ok>Elem Attributes>change the material number to 2>Ok>Auto Numbered>Thru nodes Pick the 2nd and 3 rd node>Ok>Elem Attributes>change the material number to 3>OK>Auto Numbered>Thru nodes Pick the 3 rd and 4th node>OK>Elem Attributes >change the element type to Link 34>Change the material number to 4>Change the real constant set number to 2>Ok>Auto Numbered>Thru nodes Pick the 1st and 5th node >OkApply the boundary condition and temperature.
7. Main Menu>Preprocessor>Loads>Define Loads>Apply>Thermal> Temperature>On nodes pick the 4th node >Apply >Click on TEMP and Enter Value -20>OK
Page 55
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
8. Main Menu>Preprocessor>Loads>Define Loads>Apply>Thermal> Temperature>On nodes pick the 5th node>Apply>Click on TEMP and Enter Value =800>OK.
Solution: The interactive solution proceeds.9. Main Menu>Solution>Solve>Current LS>okThe/STATUS Command window displays the problem parameters and the solve current Load Step Window is shown. Check the solution options in the/STATUS window and if all is OK, select File>CloseIn the solve Current Load Step window, Select OK, and when the solution is complete, Close the Solution is done.Post processingWe can now plot the results of this analysis and also list the computed values.10. Main Menu >General Postproc >Plot Results>Counter Plot>Nodal Solu>DOF
Page 56
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
11. Main Menu >General Postproc>List Results>Nodal Solu>Select Temperature>Ok
Result: Thus the given model is simulated and verified Temperature at each node of elements.
Page 57
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
WORD DETAILS:
Although the control will, in general, accept part programming words in any sequence, it is recommended that the following word order for each block is used.
N; G; X or U; Z or W; I; K; F; S; T;
O: PROGRAM NUMBER
The “O” followed by a 4 digit numeral value is used to assign a program number.
Example: O1002
N: SEQUENCE NUMBER
The N word may be omitted. When programmed, the sequence number following the N address is a four digit numerical value and is used to identify a complete block of information. Although ascending, descending, or duplicate numbering is allowed, it is best to program in ascending order in increments of 10. This allows for future editing and simplified sequence number search.
G: PREPARATORY COMMAND:
The two digit G command is programmed to set up the control to perform an automatic machine operation. A full list of G codes are given, one G word from each modal group and one non modal G word can be programmed on the same block.
Example: Valid N 100 G00 G40 G41 G90 G95 *G40 & G41 are from the same group.A retained G word (Modal) from one group remains active until another G word from the same group is programmed.
One-shot G word (Non-Modal) must be programmed in every block when required.
Page 58
INTRODUCTION
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
G-CODES LISTING FOR DENFORD FANUC LATHES:Note: - NOT ALL G CODES APPLY TO EACH MACHINE.
Group 1 G00 Positioning (Rapid Traverse)1 G01 Liner Interpolation (Feed)1 G02 Circular Interpolation CW1 G03 Circular Interpolation CW0 G04 Dwell0 G10 Offset Value Setting By Program6 G20 Inch Data Input6 G21 Metric Data Input9 G22 Stored Stroke Check On9 G23 Stored Stroke Check Off0 G27 Reference Point Return Check0 G28 Reference Point Return0 G29 Return from Reference Point0 G30 Return to 2nd Reference Point0 G31 Skip Function1 G32 Thread Cutting1 G34 Variable Lead Thread Cutting0 G36 Automatic Tool Compensation X0 G37 Automatic Tool Compensation Z7 G40 Tool Nose Radius Compensation cancels7 G41 Tool Nose Radius Compensation Left7 G42 Tool Nose Radius Compensation Right0 G50 Work Co-ord. Change/Max. Spindle Speed setting0 G65 Macro call12 G66 Macro Modal Call Cancel12 G67 Macro Modal Call Cancel4 G70 Finishing Cycle4 G71 Stock Removal in Turning0 G72 Stock Removal in Turning0 G73 Pattern Repeating0 G74 Peck Drilling in Z Axis0 G75 Grooving in X Axis0 G76 Thread Cutting Cycle1 G90 Cutting Cycle A1 G92 Thread Cutting Cycle1 G94 Cutting Cycle B2 G96 Constant surface Speed Control
Page 59
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
2 G97 Constant Surface Speed Control Cancel11 G98 Feed per Minute11 G99 Feed per Revolution
NOTES FOR G CODE LISTING:
Note 1:- G Codes of 0 group represent those non modal and are effective to the designed block.
Note 2:- G Codes of different groups can be commanded to the same block. If more than one G codes from the same group are commanded, the latter becomes effective.
AIXS DEFINITIONS:-
Z AXIS:-
The Z axis is along a line between the spindle and the tailstock, or the center line of rotation of the spindle. Minus (-) movements of the tool are left toward the head stock; positive (+) movements are right towards the tailstock.
X AXIS:-
The X axis is 90 degrees from the Z axis (perpendicular to the Z axis). Minus (-) movements of the tool are toward the center-line of rotation, and positive (+) movements are away from the center –line of rotation.
X: X AXIS COMMAND:-
The X word is programmed as a diameter which is used to command a change in position perpendicular to the spindle center-line.
U: X AXIS COMMAND:- The U word is an incremental distance (diameter value) which is used to
command a change in position perpendicular to the spindle center-line. The movement is the programmed value.
Z: Z AXIS COMMAND:-
Page 60
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
The Z word is an absolute dimension which is used is used to command a change in position parallel to the spindle center-line.
W: Z AXIS COMMAND:-The W word is an incremental distance which is used to command a change of
position parallel to the spindle center-line.Do not program X & U or Z & W in the same block. If an X axis command calls
for no movement it may be omitted.
X, U or P: DWELL:-
The X word is used with G04 to command a dwell in seconds. The P word is used with G04 to command a dwell in milliseconds.
I WORD:- For are programming (G02 or G03), the K Value (with sign) is programmed to define the incremental distance parallel to the Z axis, between the start of the arc and the arc center.
K WORD:-For arc programming (G02 or G03), the K value (with sign) is programmed to
define the incremental distance parallel to the Z axis, between the start of the arc and the arc center.
The maximum arc for I & K programming is limited to the quadrant. If I or K is zero, it must be omitted.
F WORD:-
a) In G99 mode the F word is used to command feed/rev.b) In G98 mode the F word is used to command feed/min.c) In G32 mode the F word specifies the lead (pitch) of the thread.
P WORD:-a) Used in automatic cycles to define the first block of a contour.b) Used with M98 to define a subroutine number.
Q WORD:-Q words are used in automatic cycles to define the last block of a contour.
Page 61
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
R WORD:- For circular interpolation (G02 or G03) the R word defines the arc radius from the center of the tool nose radius (G40 active) - or the actual radius required (G41/ G42 active).
S WORD:-a) In the constant surface speed mode (G96) the four digit S word is used to
command the required surface speed in either feet or meters per minute.b) In the direct r.p.m mode (G97), the four digit S word is used to command the
spindle speeds incrementally, in r.p.m., between the ranges available for the machine.
c) Prior to entering constant surface speed mode (9G96) the S word is used to specify a speed constraint, the maximum speed you wish the spindle to run at. To set this restraint the S word is programmed in conjunction with the G50 word.
T WORD:-The T words are used in conjunction with “M06”. Those are used to call up the
required tool on an automatic indexing turret machine, and to activate its tool offsets. M WORD:-
An M word is used to initiate auxiliary functions particular to the machine. One M code can be programmed with in one program block together with other part program information.M- CODE LIST FOR DENFORD FANUC LATHES :-
All M Codes marked with an asterisk will be executed at the end of a block (i.e., after the axis movement).NOTE: - NOT ALL M CODES ARE AVAILABLE ON EACH MACHINE.
* M00 PROGRAM STOP* M01 OPTIONAL STOP* M02 PROGRAM RESET
M03 SPINDLE FORWARDM04 SPINDLE REVERSE
* M05 SPINDLE STOPM06 AUTO TOOL CHANGEM07 COOLANT "B" ONM08 COOLANT "A" ON
* M09 COOLANT OFFM10 CHUCK OPENM11 CHUCK CLOSE
Page 62
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
M13 SPINDLE FORWARD & COOLANT ONM14 SPINDLE REVERSE & COOLANT ONM15 PROGRAM INPUT USING."MIN P" (SPECIAL FUNCTION)M16 SPECIALTOOL CALL (TOOL CALL IGNORES TURRET)M19 SPINDLE ORIENTATEM20 SPINDLE INDEX AM21 SPINDLE INDEX 2AM22 SPINDLE INDEX 3AM23 SPINDLE INDEX 4AM25 QUILL EXTENDM26 QUILL RETRACTM29 SELECT "DNC" MODEM30 PROGRAM RESET & REWINDM31 INCREMENT PARTS COUNTERM37 DOOR OPEN TO STOPM38 DOOR OPENM39 DOOR CLOSEM40 PARTS CATCHER EXTENDM41 PARTS CATCHER RETRACTM43 SWARF CONVEYOR FORWARDM44 SWARF CONVEYOR REVERSEM45 SWARF CONVEYOR STOPM48 LOCK % FEED AND % SPEED AT 100%M49 CANCEL M48 (DEFAILT)M50 WAIT FOR AXIS IN POSITION SIGNAL (CANCELS
CONTINUOUS PATH)M51 CANCEL M50 (DEFAILT)M52 PULL-OUT IN THREADING = 90 DEGRESS (DEFAILT)M53 CANCEL M52M54 DISABLE SPINDLE FLUCTUATION TESTING (DEFAILT)M56 SELECT INTERNAL CHUCKING (FROM PLC EDITION "F")M57 SELECT EXTERNAL CHUCKING (FROM PLC EDITION "F")M62 AUX.1 ONM63 AUX.2 ONM64 AUX.1 OFFM65 AUX.2 OFFM98 SUB PROGRAM CALLM99 SUB PROGRAM END
Page 63
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
1. FACING CYCLE
[BILLET X25 Z70] G21 G98;G28 U0W0;M06 T1 ;( FACING TOOL)M03 S1200;G00 X26 Z0;G94 X0 Z-0.5 F50;
Z-1.0
Z-1.5
Z-2.0
Z-2.5
Z-3.0
Z-3.5
Z-4.0
Z-4.5
Z-5.0
Z-5.5
Z-6.0
Z-6.5
Z-7.0
Z-7.5
Z-8.0
Z-8.5
Z-9.0
Z-9.5
Z-10.0
G28 U0W0;
M05;
M30;
Page 64
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Page 65
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
2. TURNING CYCLE
[BILLET X28 Z70] G21 G98;G28 U0W0;M06 T1 ;( FACING TOOL)M03 S1000;G00 X25 Z1;G94 X24 Z45 F50;
X23
X22
X21
X20
X19 Z-40
X18
X17
X16
X15
X14 Z-20
X13
X12
X11
X10
G28 U0W0;
M05;
M30;
Page 66
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Page 67
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
3. LINEAR & CIRCULAR INTERPOLATION (Milling)
G21 G94
G91 G28 Z0
G28 X0 Y0
M06 T06
M03 S1300
G90 G00 X0 Y0 Z5
[S]
G00 X2 Y30
G01 Z-1 F60
G01 X10 Y30
G03 X15 Y35 R5
G01 X15 Y37.5
G03 X10 Y42.5 R5
G01 X17 Y42.5
G02 X2 Y50
G02 X7 Y55 R5
G01 X15 Y55
G00 Z2
[V]
G00 X20 Y55
G01 Z-1 F60
G01 X27.5 Y30
G01 X33 Y55
G00 Z2
[C]
G00 X51 Y55
G01 Z-1 F60
Page 68
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
G01 X43 Y55
G03 X38 Y50 R5
G01 X38 Y35
G03 X43 Y30 R5
G01 X51 Y30
G00 Z2
[E]
G00 X69 Y55
G01 Z-1F60
G01 X56 Y55
G01 X56 Y42.5
G01 X69 Y42.5
G01 X56 Y42.5
G01 X56 Y30
G01 X69 Y30
G00 Z2
[T]
G00 X81.5 Y30
G01 Z-1 F60
G01 X81.5 Y55
G01 X74 Y55
G01 X87 Y55
G00 Z2
G91 G28 Z0
G28 X0Y0
M05
M30
Page 69
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
CFD
ANALYSIS
Page 70
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
CFD ANALYSIS OF STEAM NOZZLE
AIM: To Determine the velocity and pressure distribution in Steam Nozzle.(Boundary
conditions of -Inlet Mass flow rate=0.05kg/s, Outlet pressure 1 bar)
Step 1.Create 3D model in solid works as showing above 2D drawing.
Page 71
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Step2: Export to .IGS format.
Step 3.File>Save as>file name (nozzle.igs) >Save.
Open ICEM CFD Software,
(Start>All programs>Ansys-14>Meshing>ICEM CFD 14)
Step4:Nozzle.igs file Import to ICEM CFD
Page 72
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
(File>Import Geometry>STEP/IGS>Apply
After importing Nozzle.igs File,(Click model>Geometry click display and surfaces) it
will identify. And mean while change parts name(like Inlet,Outlet names
Step5:Geometry>repair geometry and Build Topology Tolerance valve 0.09>Apply.
Page 73
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Step6: Mesh>Global Mesh step up>Click Volume meshing parameters
Give Global Element Scale Parameters>Scale factor =1> max element 0.>Apply.
Step 7 Go to Compute mesh>select Compute(Tetrahedral mesh creating).
Page 74
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Page 75
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
\
Step 8:Select output >output solver>output solver>Ansys CFX>Ansys>Apply.
Page 76
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Click Write input>give file name>save>if you want change directory, change Done.
Visible volume mesh,
Page 77
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Step9: Save mesh file
Step10 : Open CFX Software,
(Start>All programs>Ansys-14>Fluid Dynamics>CFX 14>Click CFX-Pre.14.0)
Meshing completed.
Start Analysis in CFX-Pre processing
Step 11: File> new case>General >OK>OK
Page 78
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Step12: Import ICEM CFD file in to CFX-Pre.
Create Domain and Boundary conditions (Inlet, outlet, materials>Fluid>steam3>OK
Page 79
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Page 80
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Boundary conditions: Inlet: mass flow rate: 0.05kg/s
Outlet: Average pressure: 1 bar.
Step 13.Solver the problem: Solver control>
Define run>File name>save. Start run.
Page 81
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Now go to post processing Results:
Launch post processing Results, OK.
Page 82
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Counter plot Results (velocity and Pressure)
Page 83
SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY(AUTONOMOUS)
Experiment No. Date :
Page 84