Amplitec OMT User Manual

8/18/2019 Amplitec OMT User Manual

1/37

OMT

User Manual


2/37

Operation and Maintenance Terminal (OMT) Users Manaual

~ Page 2 ~

Content

Chapter 1 OMT Software Instruction.............................................................................................................................4

1．1 Summary...........................................................................................................4

1．2 Operation Enviroment ............................................................................................4

1．2．1 Hardware Requirement.........................................................................................................................................4

1．2．2 System Requirement.............................................................................................................................................4

1．3 OMT Monitoring Methods........................................................................................5

1．3．1 OMT Monitoring Display ....................................................................................................................................5

1．3．2 OMT Monitoring Connection...............................................................................................................................5

1．3．2．1 Local Monitoring Connection Display...........................................................................................................5

1．3．2．2 Remote Monitoring Connection Display........................................................................................................5

Chapter 2 OMT Software Operation And Application ............................................................................ ..................... 6

2．1 OMT Monitoring Connection Preparation .....................................................................6

2．1．1 Equipment Preparation.........................................................................................................................................6

2．1．2 Operation Preparation................................................................................................. ....................................... 6

2．1．3 OMT Software Installation And Login ................................................................................................................6

2．2 Create New City & Area & Equipment Information..........................................................7

2．2．1 Create New City...................................................................................................................................................7

2．2．2 Create New Area .............................................................. ................................................................ .................... 8

2．2．3 Create New Equipment ........................................................................................................................................8

2．3 Monitoring Operation Methods..................................................................................9

2．3．1 Local Connection Operation.................................................................................................................................9

2．3．2 Search Site And Search Equipment....................................................................................................................10

2．3．3 Monitoring Repeater...........................................................................................................................................14

2．3．3．1 Read / Write Basic Parameter Information...................................................................................................14

2．3．3．2 Read / Write RF Parameter Information.......................................................................................................17

2．3．3．3 Read Alarm and Read / Write Enable of Alarm Parameter Information ...................................................... 20

2．3．3．4 Resume Factory Default Setting...................................................................................................................23

2．3．4 Remote Connection Operation .................................................................. ......................................................... 24

2．3．4．1 Set Repeater“Query/setting phone number”And“Reporting number” ......................................................... 24

2．3．4．2 Set Repeater“Equipment Telephone”...........................................................................................................26

2．3．4．3 Establish Modem Remote Monitoring Communication...............................................................................27

Chapter 3 OMT Software Functions.................................................................. ........................................................... 28


3/37


~ Page 3 ~

3．1 Functions of Sections.......................................................................................... 28

3．1．1 Equipment Management Section......................... ..................................................................... ....................... 29

3．1．2 Basic Information Section ....................................................................... ........................................................... 29

3．1．3 Equipment Monitoring Section ..........................................................................................................................30

3．1．3．1 Basic Parameter Information Page ................................................................... ............................................ 30

3．1．3．2 RF Parameter Information Page ........................................................... ........................................................ 31

3．1．3．3 Alarm Parameter Information Page.............................................................. ............................................. 31

3．1．3．4 Alarm History Page................................................................ ................................................................... 32

3．1．4 Real-time Information Feedback Section...........................................................................................................32

3．2 Create New Equipment And Management ................................................................ 32

3．2．1 Create New City.................................................................................................................................................32

3．2．2 Create New Area .................................................................. .................................................................. .........33

3．2．3 Create New Master Equipment ........................................................... ............................................................ 33

3．2．4 Create New Slave Equipment.............................................................................................................................34

3．2．5 Rename City, Area, Equipment..........................................................................................................................34

3．2．6 Edit Equipment Basic Information.....................................................................................................................35

3．2．7 Delete Equipment...............................................................................................................................................35

3．2．8 Delete Area All Repeaters..................................................................................................................................36

3．2．9 Delete City All Repeaters...................................................................................................................................36

Chapter 4 Appendix........................................................................................................................................................37

4．1 The Band Corresponding Relationship Between RF Parameters Information Page’s Control Items with

Repeater Equipments’ ................................................................................................ 37

4．2 The Band Corresponding Relationship Between Alarm Parameters Information Page’s Alarm Items

with Repeater Equipments’ .......................................................................................... 37


4/37


~ Page 4 ~

Chapter 1 OMT Software Instruction

1 1 Summary

The software has Parameter Setting, Parameter Queries, Alarm Collection, etc. functions. i. e.

Parameter Setting include repeater serial number setting, monitoring center phone number setting, shift

frequency setting, alarm threshold settings, etc. Parameter Query not only check the setted configuration

information but also can collect real-time repeater working data. Summary, Parameter Query contributes to

the repeater site monitoring and fault diagnosis.

This software owns visual user interface, friendly interface, easy operation, stable and reliable

etc. features.

1 2 Operation Enviroment

1 2 1 Hardware Requirement

(1). PC 1 pcs ( the least requirement as follows );

CPU: Pentium III ( at least 800MHz ) or better processor

Memory: 512MB or larger The left storage of hard disk: at least 1GB

(2). RS-232 connecting cable 1 pcs

(3). GSM Modem ( 1 pcs )

(4). SIM card 2 pcs ( one to put in repeater, the other one to put in modem for receiving and sending

message )

1

2

2 System Requirement

(1). Operation system: Windows XP or higher version

(2). Display resolution rate should be 1024×768 or higher ( recommended standard: 1024×768 )

(3). Amplitec-OMT software

(4). Office 2003 or higher version


5/37


~ Page 5 ~

1 3 OMT Monitoring Methods

1

3

1 OMT Monitoring Display

(Figure 1)

1 3 2 OMT Monitoring Connection

1

3

2

1 Local Monitoring Connection Display

(Figure 2)

1

3

2

2 Remote Monitoring Connection Display

(Figure 3)


6/37


~ Page 6 ~

Chapter 2 OMT Software Operation And Application

2 1 OMT Monitoring Connection Preparation

2 1 1 Equipment Preparation

1. Repeater Equipment ( Including Repeaters Accessories Power Cord and RF cables )

2. One RS-232 Connection Line

3. One GSM Modem

4. Two GSM SIM Cards ( to be used in GSM Modem and repeater equipment to send and receive

message )

2 1 2 Operation Preparation

1. Set up repeater equipment and switch on the power.

2. Please connect the PC and repeater equipment by RS-232, and make sure the RS-232 cable IDECD

has been finished installation. ( for details please take RS-232 CD as reference )

2 1 3 OMT Software Installation And Login

1. The new version OMT software do not need to run the installation steps, just copy the whole folder from

the software disk to your computer.

2. Double click the icon “OMT.exe” to login the software. , main OMT interface ( show as Figure 4 ),

the code in chart stands for:

(1). Equipment Management Section

(2). Basic Information Section

(3). Equipment Monitoring Section

(4). Real-time Information Feedback Section


7/37


~ Page 7 ~

(Figure 4: OMT Interface)

2 2 Create New City & Area & Equipment Information

Note: When you login OMT Equipment Management Interface, and the repeater equipment you want to

mornitor was existed ( for example Figure 5: MasterEquipment0 and SlaveEquipment1 ), then it is no need

to go through bellow 2.2 procedure and get into 2.3 process directly.

(Figure 5)

2 2 1 Create New City

1. After login, users can see software main interface ( Equipment Management Section ) on the left side,

right click mouse, there will show a list menu. ( Figure 6 )

2. Left click “New City” to create a monitoring city name.


8/37


~ Page 8 ~

(Figure 6)

2 2 2 Create New Area

1. Right click the mouse which point to New City, there will show a list menu. ( Figure 7 )

2. Left click “New Area” to create a monitoring area name.

(Figure 7)

2 2 3 Create New Equipment

1. Right click the mouse which point to New Area, there will show a list menu. ( Figure 8 )

(Figure 8)

2. Left click “New Equipment” to create a monitoring repeater. Fill in the basic information of the monitoring

repeater then click OK to achieve. ( Figure 9 )


9/37


~ Page 9 ~

(Figure 9)

2 3 Monitoring Operation Methods

2

3

1 Local Connection Operation

Before to start bellow local mornitoring connection, it is appreciated that the users make sure two points:

（1）Make sure that the repeaters have been set up and it is power on and it can work normally.

（2）Make sure that the PC and repeater equipment is connected by RS-232.

Please follow bellow operation procedures:

1. Left click the first column “Communication Link” on top left corner as Figure 10:

(Figure 10)

2. On “Communication type” please select “Local serial port”, then on “Current Port” please select the

corresponding COM port which is connected to the repeater equipment by RS-232. ( Figure 11 )

3. Click “Connect”, if the selection of the correct COM port, the red light will turn to green color. ( Figure 11 )


10/37


~ Page 10 ~

(Figure 11)

2 3 2 Search Site And Search Equipment

Note: When it is first time to proceed the real-time mornitoring communication connection for the new

created equipment, it is appreciated that to proceed “Search Site” and “Search Equipment” frist, just in

order to make sure that OMT and equipment can be identified and match each other in intellectualization.

1. Select the corresponding repeater equipment on the left side ( Equipment Management Section ) as

Figure 12:

(Figure 12)

2. In Equipment Monitoring Information Section please select “Basic Parameter Information”, left click the

button “Search Site” on the right lower side. ( Figure 13 )


11/37


~ Page 11 ~

(Figure 13)

3. Get the detail information of site number and equipment number which repeater currently connected.

( Figure 14 )

(Figure 14)

4. Please select the corresponding repeater equipment on the left side ( Equipment Management Section )

and right click it, the equipment management function manu will appear. ( Figure 15 )

(Figure 15)

5. Left click “Edit Equipment”, you will see the equipment basic information input box as shown in figure 16

on the left side.

(Figure 16)

6. Change the site number and equipment number in the dialogue box brought out and ensure that the two

groups of the number are completely match with the numbers as third step you’ve got. And then click ok.

( As shown in figure 16 on the right side. )


Figure 17:


12/37


~ Page 12 ~

(Figure 17)


button “Search Site” on the right lower side. ( Figure 18 )

(Figure 18)

9. Get the detail information which equipment connected, including city , region and the name of

equipment ,the number of site, and the number of equipment etc. ( As shown in figure 19 on the left side. )

And find the corresponding equipment in the main interface of the software shown on the left side.

( Equipment Management Section ) ( As shown in figure 19 on the right side. )

(Figure 19)


13/37


~ Page 13 ~


Figure 20:

(Figure 20)


button “Search Equipment” on the right lower side. ( Figure 21 )

(Figure 21)

12. Please wait for seconds and pay attention on feedback section on the right downward inferior, the

“Transmit” and “Receive” information of the repeater equipment will appear.

13. When it appears “Update the equipment parameters is successful!”, means OMT search equipment

procedure and identified in intellectualization successfully, then please go on next step. ( Figure 22 )

(Figure 22)


14/37


~ Page 14 ~

2 3 3 Monitoring Repeater

2

3

3

1 Read / Write Basic Parameter Information

Read Basic Parameter Information

1. Please select the corresponding repeater equipment on the left side. ( Equipment Management Section )

( Figure 23 )

(Figure 23)

2. Enter “Basic Parameter Information“ page, pick the items you need to check. ( Figure 24 )

(Figure 24)

3. Click “Read“ button and pay attention on the feedback section on the right downward inferior, there will

be “Transmit“ and “Receive“ message of the repeaters going on the feedback section. ( Figure 25 )


15/37


~ Page 15 ~

(Figure 25)

4. When communication is successful, the updated information will immediately appear to the “Status”

column as bellow charge. ( Figure 26 )

(Figure 26)

Write Basic Parameter Information


( Figure 27 )

(Figure 27)

2. Enter “Basic Parameter Information“ page, pick the items you need to set, input the correct basic

parameters on the corresponding “Setting” column. ( For example as bellow Figure 28, to set parameters

“Query/setting phone number1~5” and “Reporting number” as “13800138000”. )


16/37


~ Page 16 ~

(Figure 28)

3. Click “Write“ button and pay attention on the feedback section on the right downward inferior, there will


(Figure 29)4. When communication is successful, the updated information will immediately appear to the “Status”

column as Figure 30.

(Figure 30)


17/37


~ Page 17 ~

2 3 3 2 Read / Write RF Parameter Information

Note: Please refer to the appendix contents in the end of the text for the band corresponding relationship

between RF parameters information page's control items with repeater equipments'.

Read RF Parameter Information


( Figure 31 )

(Figure 31)

2. Enter “RF Parameter Information“ page, pick the items you need to check. ( Figure 32 )

(Figure 32)



(Figure 33)


18/37


~ Page 18 ~

4. When communication is successful, the updated information will immediately appear to the “Status”

column as bellow charge. ( Figure 34 )

(Figure 34)

Write RF Parameter Information


( Figure 35 )

(Figure 35)

2. Enter “RF Parameter Information“ page, pick the items you need to set, input the correct RF parameters

on the corresponding “Setting” column. ( Figure 36 )


19/37


~ Page 19 ~

(Figure 36)



(Figure 37)4. When communication is successful, the updated information will immediately appear on the “Status”


(Figure 38)


20/37


~ Page 20 ~

2 3 3 3 Read Alarm and Read / Write Enable of Alarm Parameter Information

Note: Please refer to the appendix contents in the end of the text for the band corresponding relationship

between alarm parameters basic information page's alarm items with repeater equipments'.

Read Alarm and Enablement of Alarm Parameter Information


( Figure 39 )

(Figure 39)

2. Enter “Alarm Parameter Information“ page, pick the items you need to check. ( Figure 40 )

(Figure 40)



(Figure 41)


21/37


~ Page 21 ~

4. When communication is successful, the updated information will immediately appear to the “Status” and

“Enable” column as Figure 42.

(Figure 42)

Write Enablement of Alarm Parameter Information


( Figure 43 )

(Figure 43)

2. Enter “Alarm Parameter Information“ page, pick the items you need to set, input the correct enable of

alarm parameters on the corresponding “Setting” column. ( Figure 44 )


22/37


~ Page 22 ~

(Figure 44)

3. Click “Write(Enable)“ button and pay attention on the feedback section on the right downward inferior,

there will be “Transmit“ and “Receive“ message of the repeaters going on the feedback section. ( Figure

45 )

(Figure 45)

4. When communication is successful, the updated information will immediately appear to the “Enable”


(Figure 46)


23/37


~ Page 23 ~

2 3 3 4 Resume Factory Default Setting

When the users need to resume factory default setting, please go on bellow procedures ( Note: When the

repeaters are resumed factory default setting, all the parameters which were set before will be resumed to

initial status. If the users do not need to resume factory default setting, please forget this step. )


( Figure 47 )

(Figure 47)

2. Enter “Basic Parameter Information“ page, pick the items you need. ( Figure 48 )

(Figure 48)

3. Click “Default Equipment” button and pay attention on the feedback section on the right downward

inferior, there will be “Transmit“ and “Receive“ message of the repeaters going on the feedback section.

4. When it appears “Default the repeater is successful!”, resume factory default setting sucessfully, please

go on next step. ( Figure 49 )


24/37


~ Page 24 ~

(Figure 49)

2 3 4 Remote Connection Operation

2

3

4

1 Set Repeater“ Query/setting phone number”And“ Reporting number”

1. Power on the repeater and marke sure PC and repeaters are connected by RS-232.


(Figure 50)

3. Select “Local serial port” on “Communication type”, then please select the corresponding COM port

which is connected to the repeater equipment by RS-232 on “Current Port”. ( Figure 51 )

4. Click “Connect” button, if the selection of the correct COM port is successful, the red light will turn to

green color. ( Figure 51 )

(Figure 51)


( Figure 52 )


25/37


~ Page 25 ~

(Figure 52)

6. Enter “Basic Parameter Information” page, pick item “Query/setting phone number” and “Reporting

number”, set modem SIM card numbers which will be connected to PC in “Set Value” column. ( Figure 53 )

(Figure 53)



(Figure 54)

8. When communication is successful, the updated information will immediately appear on the “Status”



26/37


~ Page 26 ~

(Figure 55)

2 3 4 2 Set Repeater“ Equipment Telephone”

1. Please select the corresponding repeater equipment on the left side ( Equipment Management Section )

and right click it, the equipment management function manu will appear. ( Figure 56 )

(Figure 56)

2. Left click “Edit Equipment”, you will see the equipment basic information input box as Figure 57.


27/37


~ Page 27 ~

(Figure 57)

3. Input the SIM card number which was inserted into the repeaters, click “OK” button.

2

3

4

3 Establish Modem Remote Monitoring Communication

1. Pull out the RS-232 cable which was connected to the repeater, replace it by a modem. In the same time

please make sure that the modem antenna and power cord is in correct connections, and make sure the

repeater after power on it can work normally. ( Also it is appreciated to make sure the modem antenna has

been installed in the repeater and fasten closely. )


(Figure 58)

3. Select “GSM Short message” on “Communication type”, then please select the corresponding COM port

which is connected to modem by RS-232 on “Current Port”. ( Figure 59 )

4. Click “Connect” button, if the selection of the correct COM port is successful, the red light will turn to

green color. ( Figure 59 )


28/37


~ Page 28 ~

(Figure 59)

5. After the establishment of remote monitoring communication sucessful, users can start to proceed the

remote monitoring. ( Detailed monitoring operation procedures please take 2.3.3 above as reference. )

Chapter 3 OMT Software Functions

3 1 Functions of Sections

(Figure 60: OMT Interface)

OMT software screen includes the following section as chart above, the number stands for dfifferent

information sections.


29/37


~ Page 29 ~

Section 1: Equipment Management Section

Section 2: Basic Information Section

Section 3: Equipment Monitoring Section

Section 4: Real-time Information Feedback Section

3

1

1 Equipment Management Section

Section One: Equipment Management Section. It is devided different layers from up to down ( Figure 61 )

City→ Area→Main Equipment→Slave Equipment.

(Figure 61)

3 1 2 Basic Information Section

Section Two: Basic Information Section. This section is the basic information of master equipment and

slave equipment. Shown on ( Figure 62 ), each equipment includes below basic information:

Equipment belonging city

Equipment belonging area

Equipment name

Equipment current state ( Normal / Alarm )

Equipment site number

Equipment number

Equipment SIM number

Equipment installation location


30/37


~ Page 30 ~

(Figure 62)

3 1 3 Equipment Monitor ing Section

Section Three: Equipment Monitoring Section. This section includes Basic Parameter Information page, RF

Parameter Information page, Alarm Parameter Information page, Alarm History page ( 4 pages in total,

shown below ). Each repeater monitoring functions can be operated here. ( Figure 63 )

(Figure 63)

3 1 3 1 Basic Parameter Information Page

To show the repeater basic information, it can be set maually. Mean while it can show the update time.

( Figure 64 )

(Figure 64)


31/37


~ Page 31 ~

3 1 3 2 RF Parameter Information Page

To show the repeater’s RF parameters and working status, i.e. PA switch on and off, attenuantion value,

channel state, etc. Meanwhile it can show the update time. ( Figure 65 )

(Figure 65)

3 1 3 3 Alarm Parameter Information Page

Alert page is the feedback from the repeater, to let user knows any faults timely. And to show or to write all

enable alarm parameters. ( Figure 66 )


32/37


~ Page 32 ~

(Figure 66)

3 1 3 4 Alarm History Page

When there is an alarm occurs ( includes arlarm happens and eliminates ), it will show all of the alarm

status. ( Figure 67 )

(Figure 67)

3 1 4 Real-time Information Feedback Section

Section Four: Real-time Information Feedback Section. This section shows the repeater’s real time

communication data and OMT operation state. Users could pay attention to this section to know the

feedback from the repeater. ( Figure 68 )

(Figure 68)

3 2 Create New Equipment And Management

3 2 1 Create New City

1. Right click on the left side ( Equipment Management Section ), the equipment management functional

manu will appear. ( Figure 69 )

2. Select “New City” and click it to create a new city. ( Figure 69 )

(Figure 69)


33/37


~ Page 33 ~

3 2 2 Create New Area

1. Right click “New City ”, there will show a list manu. ( Figure 70 )

2. Select “New Area” and click it to create a new area. ( Figure 70 )

(Figure 70)

3 2 3 Create New Master Equipment

1. Right click “New Area”, there will show a list manu. ( Figure 71 )

(Figure 71)

2. Select “New Equipment” and the equipment information box will appear. ( Figure 72 )

3. Fill in the master equipment basic information which you are going to create. Then click “ OK”, the

creation is successful. ( Figure 72 )

(Figure 72)


34/37


~ Page 34 ~

3 2 4 Create New Slave Equipment

1. Right click “MasterEquipment0 ”, there will show a list manu. ( Figure 73 )

(Figure 73)

2. Select “New Slave Equipment” and the equipment information box will appear. ( Figure 74 )

3. Fill in the slave equipment basic information which you are going to create. Then click “ OK”, the creation

is successful. ( Figure 74 )

(Figure 74)

3 2 5 Rename City, Area, Equipment

Users can rename city , area and equipment at any time, please follow bellow procedures to go on:

1. Left click the item you want to modify.

2. Left click one more time again, the edited box will appear ( for example “ New City 0” ).

3. Fill in the new name you want, “Enter” on the keyboard then finished.


35/37


~ Page 35 ~

(Figure 75)

3 2 6 Edit Equipment Basic Information

Sometimes there is necessary to edit repeater basic information, i.e. change SIM card of the repeater, in

this situation, the original equipment information have to be changed.

Please go on following steps:

1. Please select the corresponding repeater equipment on the left side ( Equipment Management Section ),

right click it ( Figure 76 SlaveEquipment1 as bellow ), the equipment managemet manu will appear.

(Figure 76)

2. Left click “Edit Equipment”, the equipment basic information box will appear. ( Figure 77 )

(Figure 77)3. Fill in the new information of the repeater then click OK.

3 2 7 Delete Equipment

1. Right click the corresponding repeater equipment on the left side. ( Equipment Management Section )

( Figure 78 SlaveEquipment1 )


36/37


~ Page 36 ~

(Figure 78)

2. Click “Delete” and this step can be successful.

3 2 8 Delete Area All Repeaters

1. Right click “New Area ”. ( Figure 79 )

(Figure 79)

2. Click “Delete” and all repeaters can be deleted.

3 2 9 Delete City All Repeaters

1. Right click “New City ”. ( Figure 80 )

(Figure 80)

2. Click “Delete” and all repeaters can be deleted.


37/37


Chapter 4 Appendix

4 1 The Band Corresponding Relationship Between RF Parameters Information

Page’s Contro l Items with Repeater Equipments ’

Example: For “W37T-GW” as Figure 81.

(Figure 81)

4

2 The Band Corresponding Relationship Between Alarm Parameters

Information Page’s Alarm Items with Repeater Equipments’

Example: For “W37T-GW” as Figure 82.

Amplitec OMT User Manual

Documents

Transcript of Amplitec OMT User Manual