Alt Readers

PERPETUAAlternative Reader Wiring L INNOVATION

Guide

Lenel OnGuard 2010 Alternative Reader Wiring Guide, product version 6.4This guide is item number DOC-601, revision 1.029, October 2010Copyright 1997-2010 Lenel Systems International, Inc. Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Lenel Systems International, Inc.Non-English versions of Lenel documents are offered as a service to our global audiences. We have attempted to provide an accurate translation of the text, but the official text is the English text, and any differences in the translation are not binding and have no legal effect.The software described in this document is furnished under a license agreement and may only be used in accordance with the terms of that agreement. Lenel and OnGuard are registered trademarks of Lenel Systems International, Inc. Microsoft, Windows, Windows Server, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Integral and FlashPoint are trademarks of Integral Technologies, Inc. Crystal Reports for Windows is a trademark of Crystal Computer Services, Inc. Oracle is a registered trademark of Oracle Corporation. Other product names mentioned in this User Guide may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Portions of this product were created using LEADTOOLS 1991-2010 LEAD Technologies, Inc. ALL RIGHTS RESERVED.OnGuard includes ImageStream Graphic Filters. Copyright 1991-2010 Inso Corporation. All rights reserved. ImageStream Graphic Filters and ImageStream are registered trademarks of Inso Corporation.WarrantyLenel warrants that the product is free from defects in material and workmanship under normal use and service with proper maintenance for one year from the date of factory shipment. Lenel assumes no responsibility for products damaged by improper handling, misuse, neglect, improper installation, over-voltages, repair, alteration, or accident. This warranty is limited to the repair or replacement of the defective unit. In no event shall Lenel be liable for loss of use or consequential damages of any kind, however occasioned.There are no expressed warranties other than those set forth herein. Warranty espressly excludes third party additions, deletions and/or upgrades to this product, including those contained herein. Lenel does not make, nor intends, nor does it authorize any agent or representative to make any other warranties or implied warranties, and expressly excludes and disclaims all implied warranties of merchantability or fitness for a particular purpose.Returned units are repaired or replaced from a stock of reconditioned units. All returns must be accompanied by a return authorization number (RMA) obtained from the Lenel customer service department prior to returning or exchanging any product. The RMA number must appear on the outside of the shipping box and on the packing slip. Any items returned without an RMA number will not be accepted and will be returned at the customers expense. All returns must have transportation, insurance, and custom brokers fees prepaid.

LiabilityIt is expressly understood and agreed that the interface should only be used to control exits from areas where an alternative method for exit is available. This product is not intended for, nor is rated for operation in life-critical control applications. Lenel is not liable under any circumstances for loss or damage caused by or partially caused by the misapplication or malfunction of the product. Lenels liability does not extend beyond the purchase price of the product.

Alternative Reader Wiring GuideTable of Contents

Access Readers ...................................................................7

1. UL Evaluated Readers ........................................................................... 9

2. AIT Readers ........................................................................................... 92.1. AIT Reader #L-TR200 ................................................................... 9

3. AWID Readers ..................................................................................... 133.1. AWID Sentinel Prox MR-1824 ..................................................... 133.2. AWID Sentinel-Prox SP-6820, SR-2400, and MM-6800 ............. 153.3. AWID Prox with Keypad (KP-6840) ............................................. 163.4. AWID Sentinel-Prox RKP-4600 ................................................... 183.5. AWID Sentinel-Prox LR-911 ........................................................ 19

4. BAI Barcode Readers .......................................................................... 214.1. BAI Barcode Reader #BA-200 .................................................... 21

5. Banque-Tec Readers ........................................................................... 235.1. Smart Card Reader (Models BT815 and BT900/818) ................. 23

6. Baran Tec Keypads ............................................................................. 256.1. LNL826S121NN 8-bit Output Keypad Reader ............................ 256.2. Baran Tec Everswitch Proximity Reader Plus Keypad ................ 28

7. Bewator Readers ................................................................................. 317.1. Remote Card Reader Model BC18 ............................................. 31

8. Casi-Rusco Prox Readers ................................................................... 338.1. Casi-Rusco 94x, 97x Prox Readers ............................................ 338.2. Reader (Wiegand) Operation ...................................................... 358.3. Casi-Rusco 940-W Prox Lite (F/2F Mode) .................................. 368.4. Configuration for Casi-Rusco Readers ........................................ 388.5. Reader (F/2F Mode) Operation ................................................... 40

9. CEIA Readers ...................................................................................... 419.1. CEIA Freedom Reader with Keypad (Prox) ................................ 419.2. CEIA Freedom Reader (Output Protocol Clock/Data) ................. 42

10. Checkpoint Systems Readers ........................................................... 4510.1. Mirage II Readers ...................................................................... 45revision 1 3

Table of Contents10.2. Checkpoint Reader Model SN-MSC 16147 ............................... 4710.3. Mirage Proximity Reader B ....................................................... 49

11. Codeguard Series II/III ....................................................................... 5111.1. Secure Keypad Reader ............................................................. 51

12. Cross Match Readers ........................................................................ 5712.1. Cross Match 900xxx TWIC Readers ......................................... 57

13. Deister Electronics ............................................................................. 6113.1. Smart Card Reader Model PRM 5M, PRX 5 HSF ..................... 6113.2. Reader Model PRL5/2 KPL5/2 .................................................. 62

14. Dorado Readers ................................................................................ 6514.1. Dorado Reader Model 644 ........................................................ 6514.2. Dorado Reader Model 780 ........................................................ 6714.3. Dorado Reader Model 611 ........................................................ 6914.4. Dorado Elevator Reader 570 ..................................................... 6914.5. Dorado 230/240 Combination Readers ..................................... 71

15. Essex Keypads .................................................................................. 7515.1. Essex Keypad Reader #KTP-16212SLI .................................... 7515.2. Essex Keypad Reader #KTP-163SN ........................................ 77

16. HID Readers ...................................................................................... 7916.1. HID ProxPro .............................................................................. 7916.2. HID MaxiProx 5370 A-1 ............................................................. 8116.3. HID MaxiProx 5370/5375AGN00 .............................................. 8216.4. Hughes MiniProx ....................................................................... 8316.5. Classic, EPIC Swipe and Pinpad Wiegand Readers ................. 8516.6. ProxPoint Readers .................................................................... 8616.7. ProxPro II .................................................................................. 8716.8. iClass Reader/Encoder ............................................................. 8916.9. iClass Reader ............................................................................ 9116.10. iClass RK-40 ........................................................................... 9216.11. EntryProx 4045-905 ................................................................ 9416.12. SensorKey Reader .................................................................. 9616.13. HID MIFARE 6055 ................................................................... 9816.14. HID LCD and bioCLASS Readers (RWKL550/RWKLB575) . 10016.15. HID MIFARE Format Secure 6075 Reader ........................... 10316.16. HID OSDP Readers .............................................................. 10516.17. SmartID/SmartTRANS Models S10/SK10, SP10/SPK10 ...... 1074 revision 1

Alternative Reader Wiring Guide17. IDH Max ........................................................................................... 11117.1. IDH Max Door Readers ........................................................... 111

18. ID Solutions Readers ....................................................................... 11518.1. ID Solutions Model 8030/8035 Bar Code Reader ................... 115

19. Infographics Readers ....................................................................... 11719.1. Infographics Reader OTD-60 .................................................. 117

20. Integrated Engineering Readers ...................................................... 11920.1. Integrated Engineering PX007 Mifare Reader ........................ 11920.2. Desfire Reader ........................................................................ 12220.3. SmartID Readers ..................................................................... 123

21. Keri Systems Readers ..................................................................... 12721.1. Cascade and Sierra Readers (P-300, P-400, P-500, P-600 with

Keypad, P-700) .............................................................................. 127

22. Magtek Readers .............................................................................. 12922.1. Magtek 101-Millimeter Swipe Reader (Model 2105002) ......... 129

23. Mifare Readers ................................................................................ 13123.1. Mifare Model LA-WIW-PROXKEY-M ...................................... 13123.2. Iolan Reader Model LA-XXW-PRXKY-MX 1050-4021-092 ..... 133

24. Motorola Indala Readers ................................................................. 13524.1. Indala Readers ASR-120, ASR-122 ........................................ 13524.2. Indala Readers ASR-503, ASR-505, ASR-110, ASR-112 ....... 13724.3. Indala Readers ASR-103, ASR-105, ASR-120, ASR-122, ASR-

124, ASR-136 ................................................................................ 13924.4. Indala Reader ARK-501 .......................................................... 14324.5. Indala Readers ASR-500, ASR-501, ASR-503, ASR-505, ASR-

110 ................................................................................................. 14524.6. Motorola BiStatix Prox Reader (BXR-610) .............................. 14724.7. Indala EM4525F Reader ......................................................... 14824.8. Motorola FlexPass Readers .................................................... 149

25. Nedap Readers ................................................................................ 15125.1. Nedap Transit Readers ........................................................... 151

26. Northern Readers ............................................................................ 15526.1. Northern BR-7 Barcode Reader .............................................. 155

27. Schlage Keypads ............................................................................. 15727.1. Schlage SERIII-W Scramble Keypad ...................................... 157

28. Secura Key Readers ........................................................................ 163revision 1 5

Table of Contents28.1. e-Tag Prox Reader #ASSY 2014040 ...................................... 16328.2. Touch Card Reader (TC-100) ................................................. 16528.3. Touch Card SK-028W Barium Ferrite Reader ......................... 167

29. Synergistics Readers ....................................................................... 16929.1. SR1054FL Swipe Card Reader ............................................... 16929.2. SR1058SLE Swipe Card Reader ............................................ 171

30. Texas Instruments Readers ............................................................. 17330.1. TI S6410 Wall Plate/S6420 Mullion Reader ............................ 173

31. XCeedID Readers ............................................................................ 17531.1. XCeedID ISO-X Reader .......................................................... 175

Index ........................................................................................................... 1796 revision 1

ACCESS READERS

Alternative Reader Wiring Guide1. UL Evaluated Readers

For more details on which readers are certified for UL Listed installations, refer to the Hardware Installation Guide, DOC-600, or the NGP Hardware Installation Guide, 55-6000E.

2. AIT Readers

2.1. AIT Reader #L-TR200

AIT readers are used for asset tracking. The reader/antenna is connected to a Wiegand data converter and attached directly to a reader interface module. The Wiegand converter changes the data from RS-485 to a standard Wiegand data string. This allows the software to function with these readers and cards. The reader can effectively read the assets up to 45 feet from the reader using asset tags L-TG100 and L-TG200.revision 1 9

AIT Readers2.1.1 Wiring the LNL-1300

AIT

Aut

omat

ed Id

entif

icat

ion

Tech

nolo

gies

+12v

GND

Rx

+12 vGND

Red LEDGrn LED

Data 00Data 01

Wiegand Data Converter

+12 v

LED (Red LED)BZR (Green LED)

Data 01Data 00

GND

RJ45TerminatingConnector

Wiring to Single Reader Interface Module

TokenIn

Token Return

Tied

Toge

ther

RJ45Connector

Pin 1

Typical Software Settings

Reader Type = Wiegand/ProxKeypad = No KeypadLED Mode = 2-Wire LED Support

Pin Outs for RS-485 ConnectionPin 8 = GroundPin 7 = Data TxPin 6 = Token InPin 5 = +12 v DCPin 4 = Token Return

Pin 2Pin 3Pin 4Pin 5Pin 6Pin 7Pin 8

AIT Reader# L-TR20010 revision 1

Alternative Reader Wiring Guide2.1.2 Wiring the LNL-1320

AIT

Auto

mat

ed Id

entif

icat

ion

Tech

nolo

gies

+12V

GND

Rx

+12VGND

RedGn

Data 00Data 01

Wiegand Data Converter# L-W1100

+12 vLED (Red LED)BZR (Green LED)Data 01Data 00GND

RJ45TerminatingConnector

Wiring to Dual Reader Interface Module

TokenIn

TokenReturn

Tied

Toge

ther

RJ45Connector

+5V

D0D0-D1

D1-

TxGND

+5V

Yel

C2NO2NC2C1

NO1NC1

W1W0n/u

AIT Reader# L-TR200

Jumper SettingsJ1 - 4 & 5 offJ2 - 1 & 2 off/3 onJ3 - 1 & 2 OnJ4 - 232 pins 1 & 2

Typical Software Settings

Reader Type = Wiegand/ProxKeypad = No KeypadLED Mode = 2-Wire LED Support

Pin Outs for RS485 Connection

Pin 8 = GroundPin 7 = Data TxPin 6 = Token InPin 5 = +12 VDCPin 4 = Token Return

Pin 1Pin 2Pin 3Pin 4Pin 5Pin 6Pin 7Pin 8revision 1 11

AIT Readers12 revision 1

Alternative Reader Wiring Guide3. AWID Readers

Use the following diagrams to wire (single wire LED control) Single/Dual Reader Interface Modules and AWID Sentinel readers.

If a Sentinel Prox reader is disconnected from the power supply and then reconnected, the readers will not read the initial card presented. Subsequent cards will be read as usual.

3.1. AWID Sentinel Prox MR-1824

This reader has an input current ranging from 250 to 650 mA. The reader distance also varies according to the current, from 15 to 25 inches. Due to this input current, the reader will need to be run off a dedicated power supply.

3.1.1 Wiring the LNL-1300

AWID

12 V

GND

Power Supply

VO

LED

BZR

CLK/D1

DATA/D0

GND

The negative current from the power supplies must be tied together

Brown

Yellow

White

Green

Red

Black

TYPICAL SOFTWARE SETTINGS

1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL

Single Reader Interface Module

AWID Sentinel Prox MR-1824

Tie to Earth Groundrevision 1 13

AWID Readers3.1.2 Wiring the LNL-1320

AWID Sentinel Prox MR-1824R

eader 1AWID

12 V

GND

Power Supply

VO

LED

BZR

CLK/D1

DATA/D0

GND

The negative current from the power supplies must be tied together



Brown

Yellow

White

Green

Red

Black

Dual Reader Interface Module

Tie to Earth Ground14 revision 1

Alternative Reader Wiring Guide3.2. AWID Sentinel-Prox SP-6820, SR-2400, and MM-6800

The following readers do not require a dedicated power supply. The current requirements for these readers range from 40-120 mA. This means that the readers can be powered from the reader interface modules. It is important to make sure that the dual reader interface module is set to UNREGULATED POWER MODE (jumper J2). This will allow the maximum amount of current for the readers.



AWID

Brown

Yellow

White

Green

Red

Black

VO

LED

BZR

CLK/D1

DATA/D0

GND

AWID Sentinel-Prox SP-6820,SR-2400, and MM-6800




Tie to EarthGround

AWID Reader 1

VO

LED

BZR

CLK/D1

DATA/D0

GND

Brown

Yellow

White

Green

Red

Black




Tie to EarthGroundrevision 1 15

AWID Readers3.3. AWID Prox with Keypad (KP-6840)

(The reader must be KP-6840 REV C-8 for proper functionality)

The reader operates at 5-12 VDC and has a current draw requirement of 50-120 mA. The reader can be powered directly from the Dual Reader Interface. The keypad uses an 8-Bit output burst and meets all Lenel functionality requirements. The reader uses a single wire LED control and the LED functionality also meets all Lenel specifications.


AWID

1 2 3

4 5 6

7 8 9

0 #*Single Reader Interface Module

Brown

Yellow

White

Green

Red

Black

VO

LED

BZR

CLK/D1

DATA/D0

GND


1. Reader Type = WIEGAND/PROX2. Keypad = 8-Bit Ouput3. LED Mode = 1-WIRE LED CONTROL

Tie toEarth

Ground16 revision 1


Reader 1

VO

LED

BZR

CLK/D1

DATA/D0

GND

Brown

Yellow

White

Green

Red

Black

AWID

1 2 3

4 5 6

7 8 9

0 #*



1. Reader Type = WIEGAND/PROX2. Keypad = 8-Bit Ouput3. LED Mode = 1-WIRE LED CONTROL


AWID Readers3.4. AWID Sentinel-Prox RKP-4600

This reader is a radio-frequency proximity reader with a virtually indestructible integrated keypad for access control systems. The reader consists of a 12-key piezoelectric keypad, transmit/receive antenna, and reader electronics, in a slim plastic housing. The reader electronics are potted with epoxy resin to protect against the environment. The reader may be mounted on a single-gang electrical utility box, or on any surface (wall, cabinet, etc.).

3.4.1 Wiring the RKP-4600 Reader18 revision 1

Alternative Reader Wiring Guide3.5. AWID Sentinel-Prox LR-911

The LR-911 requires an alternate power source of 5-15 VDC and has a current requirement of 1.5A. There are no LED's on the reader (optional). The reader has a read range of up to 11 feet. See diagram below for proper wiring and setup.


* The LR-911 feature a cone shaped read zone. Theoptimal read zone is a circular cone that is at a 45 degreeangle from the edges of the reader and extends out to 11feet away from the center of the reader. Cards can beread accurately if presented to the reader within this range.

Up to 11' fromreader

12v

GNDPower Supply

Red

Black

VO

LED

BZR

CLK/D1

DATA/D0

GND

Yellow*Allows LR-911 Read Cylcling

Green

White

Blue


AWID


1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = No-LED Controlrevision 1 19

AWID Readers3.5.2 Wiring the LNL-1320


AWID

Reader 1

12v

GNDPower Supply

VO

LED

BZR

CLK/D1

DATA/D0

GND

Red

Black

Yellow

*Allows LR-911 Read Cylcling

Green

White

Blue


1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = No-LED Control20 revision 1

Alternative Reader Wiring Guide4. BAI Barcode Readers

The BAI (BA-200) Barcode reader supports an Wiegand output format of 26, 30, and 31 bits. The reader will support the following barcode formats: 10 digit interleave 2 of 5 barcode, 8 digit interleave 2 of 5 barcode, proprietary format called AFC, and 5 character code 39 barcode. For test purposes, there were no setup modifications made. We used all pre-set factory default settings. There are two LED's on the outside of the reader. The amber light shows that there is power connected to the reader, and the green light will come on when there is a valid card read. The current firmware revision is 1006.

4.1. BAI Barcode Reader #BA-200


B A IBarcode Automation Inc.

Wiegand 0Wiegand 1

Ground

Ground

Data

Clock


24 VDCPower Supply

Ground+24 VDC


1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROLrevision 1 21

BAI Barcode Readers4.1.2 Wiring the LNL-1320

B A IBarcode Automation Inc.

Wiegand 0Wiegand 1

Ground

Gro

und

Dat

aC

lockDual Reader Interface Module

24 VDCPower Supply

Ground+24 VDC


1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL22 revision 1

Alternative Reader Wiring Guide5. Banque-Tec Readers

5.1. Smart Card Reader (Models BT815 and BT900/818)

The smart card reader operates at 12 VDC and communicates with a standard Wiegand output. It uses a single wire LED control. Follow the drawing below to connect the reader to the reader interface module.




Blue

White

Green

Yellow

Red

Black

VO

LED

BZR

CLK/D1

DATA/D0

GND

BANQUE-TECSingle Reader Interface Modulerevision 1 23

Banque-Tec Readers5.1.2 Wiring the LNL-1320



BANQUE-TEC

Reader 1

VO

LED

BZR

CLK/D1

DATA/D0

GND

Blue

White

Green

Red

Black


Yellow24 revision 1

Alternative Reader Wiring Guide6. Baran Tec Keypads

These keypads are available in two styles: 3 x 4 keypads (part number LNL834S121NN) and 2 x 6 keypads (part number LNL826S121NN).

6.1. LNL826S121NN 8-bit Output Keypad Reader

The reader requires a 12-28 VDC power source and has a current draw of 30 mA. Therefore, the reader can be powered directly from either of the reader interface modules.

The wiring diagrams describe wiring if the keypad is being connected in line with another Lenel supported reader and the LED support for the keypad is being used. The keypad features a 2-Wire LED configuration. If the LED support for this keypad is not being used, omit the connections for those two wires. The reader is using a standard 8-bit output format.revision 1 25

Baran Tec KeypadsImportant: Make sure that the LED control is connected for only one reader. Both reader LEDs can not be connected at the same time.


The wiring diagram has the 2 x 6 keypad depicted. A 3 x 4 keypad may also be used.

1

3

5

7

9

*

2

4

6

8

0

#Brown

Yellow

White

Green

Red

Black

VO

LED

BZR

CLK/D1

DATA/D0

GND

H I D

HID ProxPoint Reader


GND - Black

Data 1 - White

Data 0 - Green

5-12VDC - Red


1. Keypad = 8-Bit Output2. LED Mode = 2-WIRE LED CONTROL3. Wiegand/Prox data type26 revision 1


The wiring diagram has the 2 x 6 keypad depicted. A 3 x 4 keypad may also be used.

Brown

Yellow

White

Green

Red

Black

H I D

HID ProxPoint Reader

GND - Black

Data 1 - White

Data 0 - Green

5-12VDC - Red

Reader 1

VO

LED

BZR

CLK/D1

DATA/D0

GND



1. Keypad = 8-Bit Output2. LED Mode = 2-WIRE LED CONTROL3. Wiegand/Prox data type

1

3

5

7

9

*

2

4

6

8

0

#revision 1 27

Baran Tec Keypads6.2. Baran Tec Everswitch Proximity Reader Plus Keypad

The BaranTec Everswitch reader operates at 5-12 VDC. The maximum current draw is 150 mA.


TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = 8-bit Output Keypad3. LED Mode = 1-WIRE LED CONTROL

BrownWhite

Green

Red

Black

Single ReaderInterface Module

DATA/D0

VO

LED

BZR

CLK/D1

GND

Tie to EarthGround

*

4

# 9 0

7 8

5 6

3

1 2

1k,1%

Supervision: Not Supervised, Normally Open

Gray

Tamper Input28 revision 1



1. Reader Type = WIEGAND/PROX2. Keypad = 8-bit Output Keypad3. LED Mode = 1-WIRE LED CONTROL

Dual Reader InterfaceModule

Reader 1

VOLEDBZR

CLK/D1

DATA/D0GND

Brown

White

Green

Red

Black

Tie to EarthGround

*

4

# 9 0

7 8

5 6

3

1 2

1k,1%

Supervision: Not Supervised, Normally Open

Tamper Input

Grayrevision 1 29

Baran Tec Keypads30 revision 1

Alternative Reader Wiring Guide7. Bewator Readers

7.1. Remote Card Reader Model BC18

The reader does not require a separate power supply when being connected to the Dual Reader Interface Module. However, the reader will need an alternate 5 VDC power connection if it is connected to a Single Reader Interface Module. The recommended draw is 40 mA and the reader needs to be connected to 5 VDC. Also, be sure to set up Jumper J2 for REGULATED power mode. J4 should be configured for 5 VDC. Recommended operating temperature: -10 to 55 C.


Green

Yellow

Grey

White

Blue

VO

LED

BZR

CLK/D1

DATA/D0

GND


5 VDCPowersupply +

-

BC18

BE

WA

TOR

TYPICAL SOFTWARE SETTINGS1. Reader Type = ALL OTHER READERS2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROLrevision 1 31

Bewator Readers7.1.2 Wiring the LNL-1320

Reader 1

Reader 2

VO

LED

BZR

CLK/D1

DATA/D0

GND

Green

Yellow

Grey

White

Blue


BC18

BEW

ATO

R

TYPICAL SOFTWARE SETTINGS1. Reader Type = ALL OTHER READERS2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL32 revision 1

Alternative Reader Wiring Guide8. Casi-Rusco Prox Readers

8.1. Casi-Rusco 94x, 97x Prox Readers

This reader operates at 12 VDC. The average current draw with Power Level set to Low (SW-2) is 75 mA. See manual for volt and current recommendations.


Brown (Green LED )

Blue (Red LED)

White (D1)

Green (D0)

Red (+12VDC)

Black (Ground )


DATA/D0

VO

LED

BZR

CLK/D1

GND

Tie to Earth Ground

CASI -RUSCO

R Y G

TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = 8 bit (if used)3. LED Mode = 2-WIRE LED CONTROLrevision 1 33

Casi-Rusco Prox Readers8.1.2 Wiring the LNL-1320

VO

LED

BZR

D1/CLK

D0/DATA

GND

VO

LED

BZR

D1/CLK

D0/DATA

GND

REA

DER

1R

EAD

ER

2


CASI-RUSCO

R Y G

Black (Ground )

Blue (Red LED)

Brown (Green LED )Red (+12VDC)

Green (D0)White (D1)

TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = 8 bit (if used)3. LED Mode = 2-WIRE LED CONTROL34 revision 1

Alternative Reader Wiring Guide8.1.3 Set the 94x/97x DIP Switches

Casi-Rusco 94x, 97x DIP switch settings

8.2. Reader (Wiegand) Operation

Three LED lights across the top of the Casi-Rusco prox readers signify the mode of operation.

Status Indicators

AUDIO RED LED YELLOW LED

GREEN LED

LED Operation:

Locked --- Solid light Dim light Dim light

Card Only --- Slow-blinking light Dim light Dim light

Card or PIN --- Slow-blinking light Dim light Slow-blinking light

Card and PIN --- Slow-blinking light Dim light Dim light

Unlocked --- Slow-blinking light Dim light No light

Facility Code Only --- Slow-blinking light Dim light Dim light

Beeper Operation:

1234

ON OFF

Gray Area represents switch position

5678

ON OFF

DIP Switch setup for reader

Wire connector on

back of reader

SW-2

SW-3

Switch 5, 6 = Off WiegandSwitch 7 = On, Switch 8 = Off Beeper Sound Low

Reader (Backplate Removed)

Switches 1,4 = Off, Switches 2,3 = On -Power Level = Lowrevision 1 35

Casi-Rusco Prox Readers8.3. Casi-Rusco 940-W Prox Lite (F/2F Mode)

The Dual Reader Interface Module can support Casi-Rusco readers in the F/2F mode of operation. This is only supported on Dual Reader Interface Modules with firmware 1.13 or higher. The 940-W Prox Lite is the 94x or 97x proximity reader in OnGuard, used in F/2F mode.

This reader operates at 12 VDC. The average current draw with Power Level set to Low (SW-2) is 75 mA. See manual for volt and current recommendations.

Access Granted Two beeps No light for 5 seconds

Blinks once Blinks 5 times

Access Denied Three beeps Stops blinking for 5 seconds

Blinks once Dim light

Invalid Badge Single beep Blinks 6 times --- ---

In a Card and PIN Configuration:

Access Granted (once a valid PIN is entered, the door opens)

Single beep --- Dim light Dim light

Access Denied Single beep If no PIN is entered, the red LED blinks 6 times.

Dim light Dim light

Status Indicators


GREEN LED36 revision 1


VO

LED

BZR

D1/CLK

D0/DATA

GND

VO

LED

BZR

D1/CLK

D0/DATA

GND

REA

DER

1R

EAD

ER

2


CASI-RUSCO

R Y G

Black (Ground )

Blue (Red LED)

Brown (Green LED )Red (+12VDC)

White (D1)

TYPICAL SOFTWARE SETTINGS1. Reader Type = F/2F format2. Keypad = NO KEYPAD3. LED Mode = 2-WIRE LED CONTROLrevision 1 37

Casi-Rusco Prox Readers8.3.2 Set the 940w DIP Switches

Casi-Rusco 940w DIP switch settings

8.4. Configuration for Casi-Rusco Readers

The Casi-Rusco readers can be configured for Wiegand/Prox or F/2F format.

1234

ON OFF

Gray Area represents switch position

5678

ON OFF

DIP Switch setup for reader

Wire connector on

back of reader

SW-2

SW-3

Switch 5 = On, 6 = Off F/2FSwitch 7 = On, Switch 8 = Off Beeper Sound Low

Reader (Backplate Removed)

Switches 1,4 = Off, Switches 2,3 = On -Power Level = Low38 revision 1

Alternative Reader Wiring Guide8.4.1 Casi-Rusco Readers as a Wiegand/Prox Type

In order to configure the software correctly, refer to the following screenshot. This screen can be launched by selecting Card Formats from the Administration menu in either ID CredentialCenter or System Administration.

The configuration for the Casi-Rusco within the access control system is as follows:

Reader Type Wiegand/Prox format

Keypad Type 8 bit (if keypad is used)

Reader Settings 2-wire LED control

8.4.2 Casi-Rusco Readers as a Dual Reader Interface in F/2F Format

The configuration for this reader in F/2F mode is different. Refer to the following screenshot.revision 1 39

Casi-Rusco Prox ReadersThe default configuration for the Casi-Rusco within the access control system is as follows:

Reader Type Select Dual Interface Rdr 1 (F/2F format) or Dual Interface Rdr 2 (F/2F) format

Keypad Type The keypad type does not apply when using F/2F format

Reader Settings 2-wire LED control

8.5. Reader (F/2F Mode) Operation

Three LED lights across the top of the Casi-Rusco prox readers signify the mode of operation.

Status Indicators


GREEN LED

LED Operation:

Locked --- Solid light Dim light Dim light

Card Only --- Slow-blinking light Dim light Dim light

Card or PIN --- --- Dim light Slow-blinking light

Card and PIN --- Slow-blinking light Dim light Dim light

Unlocked --- --- Dim light Slow-blinking light

Facility Code Only --- Slow-blinking light Dim light Dim light

Beeper Operation:

Access Granted Single beep --- --- ---

Access Denied Single beep Blinks 6 times --- ---

Invalid Badge Single beep Blinks 6 times --- ---

In a Card and PIN Configuration:

Access Granted (once a valid PIN is entered, the door opens)

Single beep --- Dim light Dim light

Access Denied Single beep If no PIN is entered, the red LED blinks 6 times.

Dim light Dim light40 revision 1

Alternative Reader Wiring Guide9. CEIA Readers

9.1. CEIA Freedom Reader with Keypad (Prox)

The maximum power rating on the Freedom Reader is between 5-30 VDC. The normal current draw for the reader is 40 mA. The keypad on the reader operates using a 4-bit output. This is not the standard format. This is the only format that is tested and supported by Lenel. The LED functions using single wire LED control. Both the keypad and the LED meet all the requirements for functionality that Lenel requires. Follow the diagrams below to wire the reader properly.


VO

LED

BZR

CLK/D1

DATA/D0

GND

1 32

4 65

7 98

#0*



1. Reader Type = WIEGAND/PROX2. Keypad = 4-Bit Output3. LED Mode = SINGLE WIRE LED CONTROLrevision 1 41

CEIA Readers9.1.2 Wiring the LNL-1320

9.2. CEIA Freedom Reader (Output Protocol Clock/Data)

This reader operates typically on 25 mA, peak 50 mA at 5-30 VDC.

Reader 1

VO

LED

BZR

CLK/D1

DATA/D0

GND

1 32

4 65

7 98

#0*

Connections made to terminal strip on back of reader



1. Reader Type = WIEGAND/PROX2. Keypad = 4-Bit Output3. LED Mode = SINGLE WIRE LED CONTROL42 revision 1



Tie to Earth Ground


1. Reader Type = All other readers2. Keypad = No Keypad 3. LED Mode = 1 WIRE LED CONTROL DATA/D0

VO

LED

BZR

CLK/D1

GND

Red

Green

WhiteBrown

Blackrevision 1 43

CEIA Readers9.2.2 Wiring the LNL-1320

Dual Reader Interface Module Tie to

Earth Ground


1. Reader Type = All other readers2. Keypad = No Keypad 3. LED Mode = 1 WIRE LED CONTROL

DATA/D0

VO

LED

BZR

CLK/D1

GND

Red

Brown

White

GreenBlack44 revision 1

Alternative Reader Wiring Guide10. Checkpoint Systems Readers

Use the following diagrams to wire (single wire LED control) Single/Dual Reader Interface Modules and Checkpoint Systems readers.

10.1. Mirage II Readers


TYPICAL SOFTWARE SETTINGS1. 2-Wire LED Support2. No keypad3. Wiegand/Prox data type

Checkpoint SystemsMirage II Reader


GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SG

Black - Ground

Brown - LED

White - Data 1

Red - 12 VDC

Green - Data 0revision 1 45

Checkpoint Systems Readers10.1.2 Wiring the LNL-1320

RE

AD

ER

1R

EA

DE

R 2

VO

LED

BZR

D1/CLK

D0/DATA

GND

VO

LED

BZR

D1/CLK

D0/DATA

GND


TYPICAL SOFTWARE SETTINGS1. 2-Wire LED Support2. No keypad3. Wiegand/Prox data type4. Use Unregulated Mode for jumper J2

Red - 12 VDC

Brown - LED

White - Data 1

Green - Data 0

Black - Ground

Checkpoint SystemsMirage II Reader46 revision 1

Alternative Reader Wiring Guide10.2. Checkpoint Reader Model SN-MSC 16147

This Checkpoint reader is operated at 12 VDC and has a current draw of 75 mA.



Checkpoint Reader Model SN-MSC 16147


1. Reader Type = Single Interface (Weigand/Prox)2. LED Mode = 2 Wire LED Control

GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SG

Checkpoint

Black

White

Green

Red

Brownrevision 1 47


REA

DER

1R

EAD

ER 2

VO

LED

BZR

D1/CLK

D0/DATA

GND

VO

LED

BZR

D1/CLK

D0/DATA

GND

TYPICAL SOFTWARE SETTINGS1. Reader Type = Single Interface (Weigand/Prox)2. LED Mode = 2 Wire LED Control

Dual ReaderInterface Module

Checkpoint

Red

White

Black

Green

Brown

Checkpoint Reader Model SN-MSC 1614748 revision 1

Alternative Reader Wiring Guide10.3. Mirage Proximity Reader B

The Mirage Proximity Reader B is a 33-bit prox reader. It operates at 12 VDC 10%. The average current draw is 50 mA.


White

Green

Red

Black

DATA/D0

VO

LED

BZR

CLK/D1

GND

Tie toEarth

Ground

TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROLrevision 1 49



Reader 1

VO

LEDBZR

CLK/D1

DATA/D0GND

White

Green

Red

Black

Tie toEarth

Ground


1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROL50 revision 1

Alternative Reader Wiring Guide11. Codeguard Series II/III

11.1. Secure Keypad Reader

The reader operates at +8 to +12 VDC unregulated. The average current draw is 100 mA (TYP) 180 mA (MAX) with display OFF and 280 mA (TYP) 350 mA (MAX) with display ON.

11.1.1 Set the Mode Dials

`

1 2

543

0E F

8

D

B69

CA 7

`

1 2

543

0E F

8

D

B69

CA 7

`

1 2

543

0E F

8

D

B69

CA 7

Mode Dials in Rear Panel

(Located Behind Rubber Blanking Plug)

Facility Code (Modes 1-6 only, set to 0,0 for modes 7-A)

Operating Mode(See Card Formats)

IMPORTANT: The Facility Code and Operating Mode must be set PRIOR to the installation of the reader.

To Set Facility CodeEach switch is numbered 0 to F, allowing 256 different facility codes to be selected (00 to FF). The switch on the left sets the most-significant digit of the Facility Code, the switch on the right sets the least-significant digit of the code. Disconnect power from the unit when altering the setting of these switches. revision 1 51

Codeguard Series II/III11.1.2 Card Formats

Code Lengths

Mode 0 Supports 1 to 9 digits with a transmitted block length of 40 bits with even/odd parity.

Mode 1 Supports 1 to 4 digits with a transmitted block length of 34 bits.

Mode 2 Supports 1 to 4 digits with a transmitted block length of 26 bits.

Mode 3 Supports 1 to 4 digits with a transmitted block length of 26 bits with even/odd parity.

Mode 4 Supports 5 digits with a transmitted block length of 34 bits.

Mode 5 Supports 5 digits with a transmitted block length of 26 bits.

Mode 6 Supports 5 digits with a transmitted block length of 26 bits with even/odd parity.

Model series

Mode Total number of bits on card

Facility codeStarting bit/Number of bits

Card numberStarting bit/Number of bits

Issue codeStarting bit/Number of bits

Number of even parity bits

Number of odd parity bits

Special

II or III 0 40 1 / 8 9 / 30 0 / 0 20 20 None

II or III 1 34 1 / 8 17 / 16 0 / 0 0 0 None

II or III 2 26 1 / 8 9 / 16 0 / 0 0 0 None

II or III 3 26 1 / 8 9 / 16 0 / 0 13 13 None

II or III 4 34 1 / 8 17 / 16 0 / 0 0 0 None

II or III 5 26 1 / 8 9 / 16 0 / 0 0 0 None

II or III 6 26 1 / 8 9 / 16 0 / 0 13 13 None

III only 7 4-bit keypad emulation, 0-9 codes only

III only 8 8-bit keypad emulation, 0-9 codes only

III only 9 4-bit keypad emulation, 0-9 plus # and * codes transmitted

III only A 8-bit keypad emulation, 0-9 plus # and * codes transmitted52 revision 1



1. Reader Type = Wiegand / Prox2. Keypad = 4 or 8 Bit Output (see mode)3. LED Mode = 2-WIRE LED CONTROL

DATA/D0VO (No Connection)

LED

BZR

CLK/D1

GND


12

34

56

78

Connector Pin Block

Pin 2

Pin 8

Pin 4

Pin 5

Pin 7

Pin 38-12VDC Power

Supply-+revision 1 53

Codeguard Series II/III11.1.4 Wiring the LNL-1320

DATA/D0

LED

BZR

CLK/D1

GND


12

34

56

78

Connector Pin Block

Pin 7

Pin 5

Pin 8

Pin 4

IMPORTANT! This reader cannot be powered from the Dual Reader Interface Module. There must be a common ground between the Power Supply and the Dual Reader Interface Module.

Pin 2 8-12VDC Power Supply

-+Pin 3

VO (No Connection)

TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand / Prox2. Keypad = 4 or 8 Bit Output (see mode)3. LED Mode = 2-WIRE LED CONTROL54 revision 1

Alternative Reader Wiring Guide11.1.5 LED Operation

Mode Series II Secure Keypad Series III Secure Keypad

Card and PIN N/A Blinking red at bottom of keypad

Card only N/A Blinking red at bottom of keypad

Card or PIN Blinking red and [*] key on keypad solid

Blinking red at bottom of keypad

Cipher lock emulation Blinking red and [*] key on keypad solid


Facility code mode N/A

* This mode is unsupported. Any entry within the Code Length will let someone gain access because the facility code is set in the reader.


Locked Solid red at bottom of keypad Solid red at bottom of keypad

Unlocked Solid yellow at bottom of keypad Solid yellow at bottom of keypad

Power up condition Blinking red at bottom of keypad. Keypad will display firmware version and operating mode.

Keypad will display firmware version and operating mode

Access granted Blinking yellow at bottom of keypad Blinking yellow at bottom of keypad

Access denied Solid red at bottom of keypad Solid red

Waiting for PIN Blinking red and [*] key on keypad solid

Blinking red and yellow, * key on keypad solid

Waiting for second card Blinking yellow at bottom of keypad

* This mode is unsupported because there are times when a second entry creates an invalid card format.

Alternating red and yellow at bottom of keypad

Reader LED software setup

2-wire LED control 2-wire LED control

Reader type Wiegand/Prox Wiegand/Prox

Keypad 4-bit output keypad 8-bit output keypad

+ 12 V Pin 3 Pin 3

DAT 0 Pin 7 Pin 7

DAT 1 Pin 5 pin 5

LED Pin 4 Pin 4

BZR Pin 8 Pin 8

GND Pin 2 Pin 2revision 1 55

Codeguard Series II/III The star [*] key must be pressed prior to PIN entry.

The star [*] key always illuminated red.

Upper left LED blinks with each key press.

Pressing the [*] key will activate keypad, rescramble keys, and transmit the * key code to the OnGuard system.

Keypad commands sometimes are not accepted, likely because of the multiple functions of the star [*] key. Pressing the star [*] key twice before commands may help.

Earth ground Case ground Not connected, or connect to Pin 2 (avoid ground loops)

Mode Series II Secure Keypad Series III Secure Keypad56 revision 1

Alternative Reader Wiring Guide12. Cross Match Readers

12.1. Cross Match 900xxx TWIC Readers

Cross Match TWIC readers (models 90223, 900236, 900260) are supported. The average reader draw is 325mA @ 12 VDC. General power requirements: +9 to +18 VDC, 6W total.



Tie to Earth Ground

DATA/D0

VO

LED

BZR

CLK/D1

GND

DRAIN

Brown

White

Green

Reader LED

Black

TYPICAL SOFTWARE SETTINGS1. Reader Type = Mag w/Wiegand Output2. Keypad = Eight Bit Output Keypads 3. LED Mode = 1-WIRE LED CONTROLrevision 1 57

Cross Match Readers12.1.2 Wiring the LNL-1320

12.1.3 Custom LED Configuration

There are two options for LED functionality. These are configured by a toggle in the devices configuration web interface menu.

Local LED Control This option allows the readers internal logic to control all LED behavior.

Let Wiegand Panel Drive Grant LEDs This option lets the Lenel Hardware manage some LED behavior, such as indicating door unlocked.


Tie to Earth

Ground

DATA/D0

VO

LEDBZR

CLK/D1

GND

DRAIN

Brown

White

Green

Black

Reader LED

TYPICAL SOFTWARE SETTINGS1. Reader Type = Mag w/Wiegand Output2. Keypad = Eight Bit Output Keypads 3. LED Mode = 1-WIRE LED CONTROL58 revision 1

Alternative Reader Wiring Guiderevision 1 59

Cross Match Readers60 revision 1

Alternative Reader Wiring Guide13. Deister Electronics

13.1. Smart Card Reader Model PRM 5M, PRX 5 HSF

The smart card reader can operate between 8 and 30 VDC. In order for the reader LEDs to function properly, the reader will need to be set up for 2-wire control.


deis ere ectronics

+ Supply

D1 (C

lock)

D0 (D

ata)

GN

D

Green LE

D

Red LE

D

1 2 3 4 5 6 7 8 9 10 11 12TERMINAL STRIP ON BACK OF READER

VO

LED

BZR

CLK/D1

DATA/D0

GND




Deister Electronics13.1.2 Wiring the LNL-1320

13.2. Reader Model PRL5/2 KPL5/2

This reader can operate between 8 and 30 VDC.

deis ere ectronics

+ Supply

D1 (C

lock)

D0 (D

ata)

GN

D

Green LE

D

Red LE

D

1 2 3 4 5 6 7 8 9 10 11 12TERMINAL STRIP ON BACK OF READER

Reader 1

VO

LED

BZR

CLK/D1

DATA/D0

GND





+ Supply

D1 (C

lock)

D0 (D

ata)

GN

D

Green LED

Red LE

D

1 2 3 4 5 6 7 8 9 10 11 12TERMINAL BLOCK ON BACK OF READER

VO

LED

BZR

CLK/D1

DATA/D0

GND




Deister Electronics13.2.2 Wiring the LNL-1320

+ Supply

D1 (C

lock)

D0 (D

ata)

GN

D

Green LE

D

Red LED

1 2 3 4 5 6 7 8 9 10 11 12TERMINAL BLOCK ON BACK OF READER

Reader 1

VO

LED

BZR

CLK/D1

DATA/D0

GND




Alternative Reader Wiring Guide14. Dorado Readers

Use the following diagrams to wire Single/Dual Reader Interface Modules and Dorado readers.

14.1. Dorado Reader Model 644

For the Dorado Reader 644, a 16-position rotary switch (Trim POT) is now used for reader configuration. It is located inside the housing on the circuit board. The LED control is standard single wire. The reader should be configured to setting 8 (EMPI cards, 26-bit Wiegand).


Brown

White

Yellow

Red

Black

Dorado Reader Model 644

Green

GND

VDC 5 VDC Power Supply

TYPICAL SOFTWARE SETTINGSReader Type = Mag w/Wiegand Output

GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SG

Single Reader Interface Modulerevision 1 65

Dorado Readers14.1.2 Wiring the LNL-1320

Brown wire

Green wire

Yellow wire

Red wire

Black wire

Dorado Reader Model 644

White wire

REA

DER

1VO

LED

BZR

D1/CLK

D0/DATA

GND


DUAL READER INTERFACE MODULE CONFIGURATION1. The 1320 must be set to 5 VDC output (jumper J4)2. Use Regulated Mode for the 1320 (jumper J2)

5 VDC

TYPICAL SOFTWARE SETTINGSReader Type = Mag w/Wiegand Output66 revision 1

Alternative Reader Wiring Guide14.2. Dorado Reader Model 780


Switch Set for Mode 5ABA Card Clock &

Data Black wire

Brown wire

Green wire

White wire

Red wire

Dorado ReaderModel 780

Yellow wire

Single Reader Interface Module with aDorado 780 Card and Pin Reader

A

B

C

D

SW1

ON

OFF

Software Settings: Reader interface All other readers Dorado LED control 8 Bit Pin numbers Requires Firmware Revision for the Dual Reader Interface

10278 0 MR-52R1.04aMSC-C97-8 STO

or for Single Reader Interface10241 2 MR-50R1.06MSC (c) 95-8

GND

12 VDCPower Supply

GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SG

80 mA maximumrevision 1 67


Switch Set for Mode 5ABA Card Clock & DataYellow wire

White wire

Brown wire

Red wire

Black wire

Dorado Reader Model780

Green wire

RE

AD

ER

1R

EA

DE

R 2

VO

LED

BZR

D1/CLK

D0/DATA

GND

Dual Reader Interface Module with aDorado 780 Card and Pin Reader

VO

LED

BZR

D1/CLK

D0/DATA

GND

See manual for 12 VDC1320 Jumper settingsJ4 - OFF, J2 - UNREG

A

B

C

D

SW1

ON

OFFSoftware Settings: Reader interface All other readers Dorado LED control 8 Bit Pin numbers Requires Firmware Revision for the Dual Reader Interface

10278 0 MR-52R1.04aMSC-C97-8 STO

or for Single Reader Interface10241 2 MR-50R1.06MSC (c) 95-8 68 revision 1

Alternative Reader Wiring Guide14.3. Dorado Reader Model 611

14.4. Dorado Elevator Reader 570

This reader operates at 35 mA at +5.5 volts (regulated 4.75 to 5.75).

If you are going to power the reader from the LNL-1320, set jumper 4 to the ON position for 5 volts and jumper 2 for regulated mode.

A four-position DIP switch is located on the reader circuit board to control the reader options. The reader should be set to Mode 6. Note that the fourth switch is not used and should be set to the OFF position.

Mode A B C D Function

6 ON off ON off ABA card, all bits Wiegand

Brown wire

Green wire

Yellow wire

Red wire

Black wire

A

B

C

D

ON

DoradoReader

Model 611

White wire

VO

LED

BZR

D1/CLK

D0/DATA

GND


VO

LED

BZR

D1/CLK

D0/DATA

GND

GND

VDC 5 VDCPower Supply (35 mA)

Software Settings: Reader interface All other

readers One Wire LED Control

The Dual Reader Interface must have Jumper J4 ON for 5 VDC Operation orExternal Power supply must be used as shown below

REA

DER

1R

EAD

ER 2

See manual for voltage andcurrent recommendations.

OFFrevision 1 69


The wires are connected as follows:

Reader wire color Association on LNL-1300

Yellow BZR

Brown LED

White CLK/D1

Green DATA/D0


Tie to EarthGround

DATA/D0

VO

LED

BZR

CLK/D1

GND

Yellow

BrownWhiteGreen

Red to +5VDC

Black to Common

TYPICAL SOFTWARE SETTINGS1. Reader Type = MAG w/Wiegand Output2. Keypad = No Keypad3. LED Mode = 2-WIRE LED CONTROL70 revision 1


14.5. Dorado 230/240 Combination Readers

There are two types of these combination readers. Model 230 is a combination magnetic stripe and proximity reader. Model 240 is a combination magnetic strip and proximity reader with a keypad. These readers operate at 5-24 VDC. The typical current draw is 75 mA.

The 16 position rotary switch will control the formats of the reader and should be set to 0. Position 0 is ABA HID all bits ABA, no leading or trailing zeros, Wiegand output. For HID prox, the number of output bits on the card are not defined by selector switch.


Reader 1

VOLED

BZRCLK/D1

DATA/D0GND

Brown

White

Green

Tie to EarthGround

Yellow

Red

Black

TYPICAL SOFTWARE SETTINGS1. Reader Type = MAG w/Wiegand Output2. Keypad = No Keypad3. LED Mode = 2-WIRE LED CONTROLrevision 1 71



Brown

White

Green

Red

Black


DATA/D0

VO

LED

BZR

CLK/D1

GND

TYPICAL SOFTWARE SETTINGS1. Reader Type = MAG W/WIEGAND OUTPUT2. Keypad = EIGHT BIT OUTPUT KEYPADS3. LED Mode = 1-WIRE LED CONTROL


Reader 1

VO

LEDBZR

CLK/D1

DATA/D0GND

Brown

White

Green

Red

Black

TYPICAL SOFTWARE SETTINGS1. Reader Type = MAG W/ WIEGAND OUTPUT2. Keypad = EIGHT BIT OUTPUT KEYPADS3. LED Mode = 1-WIRE LED CONTROL72 revision 1

Alternative Reader Wiring Guiderevision 1 73

Dorado Readers74 revision 1

Alternative Reader Wiring Guide15. Essex Keypads

Use the following diagrams to wire Single/Dual Reader Interface Modules and Essex keypad readers.

15.1. Essex Keypad Reader #KTP-16212SLI

15.1.1 Wiring the LNL-1300 (Single Wire LED Control)

GND

12 VDCPower Supply

1 2

3 4

5 6

7 8

9 0

#

Brown - LED wire

Black - Ground

Orange

Red - Vcc

Green - Data 0

White - Data 1

Yellow - LED wire

Tan - Case

Blue

Essex KeypadPart # KTP-16212SLI

SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. Keypad Type = Eight bit output keypad

GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SG


Essex Keypads15.1.2 Wiring the LNL-1320 (Single Wire LED Control)

REA

DER

1R

EAD

ER 2

VO

LED

BZR

D1/CLK

D0/DATA

GND


VO

LED

BZR

D1/CLK

D0/DATA

GND

Brown - LED wire

Black - Ground

Orange

Red - Vcc

Green - Data 0

White - Data 1

Yellow - LED wire

Tan - Case Ground

Blue

1 2

3 4

5 6

7 8

9 0

#

Essex KeypadPart # KTP-16212SLI

TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. Keypad Type = Eight bit output3. Jumper J4 must be set to 12 VDC4. 2-wire LED control76 revision 1

Alternative Reader Wiring Guide15.2. Essex Keypad Reader #KTP-163SN

15.2.1 Wiring the LNL-1300 (Single Wire LED Control)

GND

12 VDC Power Supply

Brown - LED wire

Black - Ground

Orange

Red - Vcc

Green - Data 0

White - Data 1

Yellow - LED wire

Tan - Case

Blue - CCTV

31 2

64 5

97 8

# 0

Essex KeypadPart # KTP-163SN

SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. Keypad Type = Eight bit output

GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SG


Essex Keypads15.2.2 Wiring the LNL-1320 (Single Wire LED Control)

RE

AD

ER

1R

EA

DE

R 2

VO

LED

BZR

D1/CLK

D0/DATA

GND


VO

LED

BZR

D1/CLK

D0/DATA

GND

31 2

64 5

97 8

# 0

Brown - LED wire

Black - Ground

Orange

Red - Vcc

Green - Data 0

White - Data 1

Yellow - LED wire

Tan - Case Ground

Blue - CCTV

Essex KeypadPart # KTP-163SNSOFTWARE SETTINGS

1. Reader Type = Wiegand/Prox2. Keypad Type = Eight bit output3. Jumper J4 must be set to 12 VDC4. Jumper J2 must be set to Unregulated

Mode.5. 2-wire LED control78 revision 1

Alternative Reader Wiring Guide16. HID Readers

Use the following diagrams to wire Single/Dual Reader Interface Modules and HID readers.

16.1. HID ProxPro


1 - DC+

2 - GND

3 - Data 0

4 - Data 15 - Data RTN

6 - Green LED7 - Red LED8 - Beeper9 - Hold

10 - COM

11 - Tamper

TB1

Tamper SW123

P3

P1

1 2 3

SW1

HID ProxPro

12 VDC +Power Supply(125 mA)-

TYPICAL SOFTWARE SETTINGS1. Reader Type - Wiegand/Prox2. HID-09 kepad - eight-bit output keypad

HID-00 keypad - four-bit output keypad

GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SG

Single ReaderInterface Modulerevision 1 79

HID Readers16.1.2 Wiring the LNL-1320

1 - DC+

2 - GND

3 - Data 0

4 - Data 15 - Data RTN

6 - Green LED

7 - Red LED8 - Beeper9 - Hold

10 - COM

11 - Tamper

TB1

Tamper SW123

P3

P11 2 3

SW1

HID ProxPro

RE

AD

ER

1R

EA

DE

R 2

VO

LED

BZR

D1/CLK

D0/DATA

GND

VO

LED

BZR

D1/CLK

D0/DATA

GND


TYPICAL SOFTWARE SETTINGS1. Reader Type - Wiegand/Prox2. HID-09 kepad - eight-bit output keypad

HID-00 keypad - four-bit output keypad* Use the 1320 in Unregulated Mode (jumper J2)80 revision 1

Alternative Reader Wiring Guide16.2. HID MaxiProx 5370 A-1


B

A

J3

U1

J4

REA

DER

IN

TERF

AC

EN C C N O N O N C C + 12

V

GN

D

I2-

I2+

I1+

I1+

K1 K2

1

2 3

4

5 6

7

8

J2GN

D

BZR LE

D

CLK

/D1

DAT

/D0

+12V

TR+

TR-

SG

Neutral (white)Hot (black)

Ground (green)

11 - Tamper Select10 - Tamper Common9 - Hold (blue)8 - Beeper (yellow)7 - Red LED (brown)6 - GRN (orange)5 - Data RTN (black)4 - Data-1 (white)3 - Data-0 (green)2 - Ground (black)1 - +DC (red)

on

8 7 6 5 4 3 2 1

Fuse

AC

AC

- BA

T +

+ DC -

1234

ON

SMP5PM

24VDC

Fuse

AC

A

C- B

AT

+

+ DC -

1234

ON

SMP3PM

12VDC

HIDMaxiProx5370 A-1

TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. No keypadrevision 1 81

HID Readers16.3. HID MaxiProx 5370/5375AGN00


D1 D2

INP

UTS

IN 1

IN 2

IN 3

IN 4

IN 5

IN 6

IN 7

IN 8

IN 9GNDIN 10

U10

J4

IN - 5VOUT - 12V

RDR POWERREG UNREG

J2

GND

DAT

CLK

BZ

A L

EO

VO

D0

D1GN

D D

AT C

LK

BZA

LEO

V

OD0

D1 RE

ADER

2RE

ADER

1

SN

REV

PN

RS

-485

TR +

TR -

R +

R -

SG

12V

ACDC

AC

GND

J6

J5

J5, J6TERMINATOR

2W 4WJ3

RS-485

U1

U2OFF ON

S1

8 7

6 5

4

3 2 1

NO

C

N

C

NO

C

NC

RLY

2

RLY

1NO

C

NC

NO

C

N

CRL

Y 4

R

LY 3

NO

C

N

C

NO

C

NC

RLY

6

RLY

5

C2

C1

COM k5NC

NO

C2

C1

COM k3NC

NO

C2

C1

COM k1NC

NO

C2

C1

COM k2NC

NO

C2

C1

COM k4NC

NO

C2

C1

COM k6NC

NO

TB1

TB2

TB3

TB4

TB5

TB6

TB7

R120

TB12

TB11

TB10

TB9C3

TB8

Neutral (white)Hot (black)

Ground (green)

11 - Tamper Select10 - Tamper Common9 - Hold (blue)8 - Beeper (yellow)7 - Red LED (brown)6 - GRN (orange)5 - Data RTN (black)4 - Data-1 (white)3 - Data-0 (green)2 - Ground (black)1 - +DC (red)

on

8 7 6 5 4 3 2 1

Fuse

AC A

C- B

AT

+

+ DC -

1234

ON

SMP5PM

24VDC

Fuse

AC

A

C- B

AT

+

+ DC -

1234

ON

SMP3PM

12VDC

HIDMaxiProx5370 A-1

TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. No keypad82 revision 1

Alternative Reader Wiring Guide16.4. Hughes MiniProx


1 - DC+

2 - GND

3 - DATA "0"

4 - DATA "1"

5 - DATA RTN

6 - Green LED

7 - Red LED

8 - Beeper

9 - Hold

Red

Black

Green

White

Black

Orange

Brown

Yellow

Blue

N/C

N/C

Hughes MiniProx ReaderTYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. No keypad

GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SG


N/Crevision 1 83


VO

LED

BZR

D1/CLK

D0/DATA

GND

VO

LED

BZR

D1/CLK

D0/DATA

GND

RE

AD

ER

1R

EA

DE

R 2


1 - DC+

2 - GND

3 - DATA "0"

4 - DATA "1"

5 - DATA RTN

6 - Green LED

7 - Red LED

8 - Beeper

9 - Hold

Red

Black

Green

White

Black

Orange

Brown

Yellow

BlueN/C

Hughes MiniProx Reader

TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. No keypad* Use Unregulated Mode for the 1320, jumper J2

N/C

N/C84 revision 1

Alternative Reader Wiring Guide16.5. Classic, EPIC Swipe and Pinpad Wiegand Readers



+ 12 VDC

- GND


GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SG


HID Classic Swipe Reader, EPIC SwipeReader, or Pinpad Wiegand Reader

Black - Ground

Brown - Red LED

Violet - Green LED

White - Data 1

Green - Data 0

Red - 5-12 VDC

Blue - not used

Yellow - not used

Orange - notused

TYPICAL SOFTWARE SETTINGS1. 2-Wire LED Support2. No keypad3. Wiegand/Prox data type* Use unregulated mode for the 1320, Jumper J2

HID Classic Swipe Reader, EPIC SwipeReader, or Pinpad Wiegand Reader

Red - 5-12 VDC

Violet - Green LED

Brown - Red LED

White - Data 1

Green - Data 0

Black - Ground

Blue - not used

Yellow - not used

Orange - notused

RE

AD

ER

1R

EA

DE

R 2

VO

LED

BZR

D1/CLK

D0/DATA

GND

VO

LED

BZR

D1/CLK

D0/DATA

GND

Dual ReaderInterface Modulerevision 1 85

HID Readers16.6. ProxPoint Readers




H I D

ProxPoint Reader

White - Data 1

Green - Data 0

Black - Ground

Orange - LED


GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SG

Red - 5-12 VDC

Yellow - BZR


Red - 5-12 VDC

White - Data 1

Green - Data 0

Black - Ground

Yellow - BZR

REA

DER

1R

EAD

ER 2

VO

LED

BZR

D1/CLK

D0/DATA

GND

VO

LED

BZR

D1/CLK

D0/DATA

GND


H I D

ProxPoint Reader

Orange - LED86 revision 1

Alternative Reader Wiring Guide16.7. ProxPro II

The ProxPro II reader (model number 5455BBn00) operates at 5-16 VDC. The average current draw at 12 VDC is 30 mA. The LEDs and buzzer function in the same way as standard HID Wiegand/proximity readers.


Orange

Yellow

White

Green

Red

Black


HID

DATA/D0

VO

LED

BZR

CLK/D1

GND

Drain wire & Shield

to Ground





HID

Reader 1

VO

LEDBZR

CLK/D1

DATA/D0GND

Orange

YellowWhite

Green

Red

BlackShield

to Drain

Ground



Alternative Reader Wiring Guide16.8. iClass Reader/Encoder

This reader (RW300/RW400/RW400Prgm) operates at 10-16 VDC. The average current draw is 80-260 mA. When communication to the unit is successful, the LED remains solid green.

Note: Due to timing issues with the encoder, this unit cannot be connected to a multiport serial adapter.

Wiring Function DB9 pin-out (female)

Yellow Speaker Not used

Blue Hold Not used

Violet Open collector Not used

White Data 1 Not used

Green Data 0 Not used

Orange Green LED Not used

Brown Red LED Not used

Red +DC (10-16 VDC) +DC (10-16 VDC)

Black Ground DC Ground

Gray RX (serial receive) Pin 3

Red/Green DSR Not used

Pink TX (serial transmit) Pin 2

Red/Yellow DTR Not used

Drain Shield ground Pin 5

HID

PIN 2PIN 3

PIN 5

To DB9 SerialCommunication

Port on PCrevision 1 89

HID ReadersWhen configuring the access control software, this encoder will most likely be a standalone device connected to the workstation. Be sure to select a unique name for the encoder. Select HID iCLASS for the device type and iClass for the card technology.

Typical Communication Settings

Comm. port: configurable

Baud rate: 57600

Data bits: 8 bit

Parity: Even

Stop bits: 290 revision 1

Alternative Reader Wiring Guide16.9. iClass Reader

The HID iClass Reader (model numbers R10/R30/R40) operates at 10-16 VDC. The average current draw for the R10 is 65-122 mA; the R30: 80-260 mA; the R40: 80-260 mA. The LEDs and buzzer function the same as standard HID Wiegand/Prox readers.



1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROL

Orange

Brown

White

Green

Red

Black

Single Reader InterfaceModule

DATA/D0

VO

LED

BZR

CLK/D1

GND

HID



16.10. iClass RK-40

The HID iClass RK-40 reader has an 8 bit keypad. It operates at 10-16 VDC. The average current draw is 72/244 mA at 12 V. The LEDs and buzzer function the same as standard HID Wiegand/Prox readers.

Dual Reader InterfaceModule

Reader 1

VO

LEDBZR

CLK/D1

DATA/D0GND

OrangeBrownWhite

Green

Red

Black

HID

Tie to EarthGround

TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROL92 revision 1


Pin 5 (Green LED)

Pin 6 (Red LED)

Pin 4 (Data 1)

Pin 3 (Data 0)

Pin 1 (+DC (10-16V)

Pin 2 (Ground)


DATA/D0

VO

LED

BZR

CLK/D1

GND

Tie to Earth

Ground

HID

1 2 3

4 5 6

7

*98

0 #

TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = EIGHT BIT OUTPUT KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROLrevision 1 93


16.11. EntryProx 4045-905

The EntryProx is a standalone reader. It is ideal for providing single-door proximity access control.

In this configuration, the keypad does not send separate key data. When the keypad is used, it outputs the cardholder/badge ID number.

The system transmits keypad PINs while operating in Wiegand mode by processing any digit sequence terminated with the [*] key as 26-bit Wiegand data. The current facility code (set using Code 32 - 2) will be used. Entering any PIN over 65535 will cause an error condition and no data will be sent.

Because keypad data is sent in a card data format, it may not be possible to perform card and PIN operation. If 26-bit format as PIN data cannot be interpreted, be sure to enter it into the badge ID field, and not the keypad PIN number field.

Pin 5 (Green LED)

Pin 6 (Red LED)

Pin 4 (Data 1)

Pin 3 (Data 0)

Pin 1 (+DC (10-16V)

Pin 2 (Ground)


DATA/D0

VO

LED

BZR

CLK/D1

GND

Tie toEarth

Ground

HID

1 2 3

4 5 6

7

*98

0 #

TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = EIGHT BIT OUTPUT KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROL94 revision 1



Blue - not used

Green - Wiegand Data 0

White - Wiegand Data 1

Brown - Wiegand LED

DATA/D0

VO

LED

BZR

CLK/D1

GNDrevision 1 95


16.12. SensorKey Reader

This reader operates at 40 mA at 5-12 VDC.


Reader 1

VO

LEDBZR

CLK/D1

DATA/D0GND

Blu

e - n

ot u

sed

Red +12 VDC

Brown - Wiegand LED

White - Wiegand Data 1

Green - Wiegand Data 0

Black - Ground96 revision 1



1. Reader Type = WIEGAND / PROX2. Keypad = No Keypad 3. LED Mode = 1 or 2-WIRE LED CONTROL


Tie to Earth Ground

DATA/D0

VO

LED

BZR

CLK/D1

GND

(Brown)(White)(Green)

(Black)

(Red)

(Blue)revision 1 97


16.13. HID MIFARE 6055

This reader operates at 9-14 VDC (16 VDC maximum). The average current draw is 100mA at 12 VDC. A linear power supply recommended.


1. Reader Type = WIEGAND / PROX2. Keypad = No Keypad 3. LED Mode = 1 or 2-WIRE LED CONTROL


Tie to Earth Ground

DATA/D0

VO

LED

BZR

CLK/D1

GND

(Brown)

(White)(Green)

(Black)

(Red)

(Blue)98 revision 1




GND

BZRLED

CLK/D1

DATA/D0VO

YellowBrownWhite

Green

Black

Red

TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 2-WIRE LED CONTROL

Other wires not used

MIFAREHID


Reader 1

VO

LEDBZR

CLK/D1

DATA/D0GND

BrownYellowWhite

Green

Red

Black

TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 2-WIRE LED CONTROL

MIFAREHID

Other wires not usedrevision 1 99

HID Readers16.14. HID LCD and bioCLASS Readers (RWKL550/RWKLB575)

HID LCD and bioCLASS models RWKL550 and RWKLB575 are supported as either Wiegand or OSDP readers.

16.14.1 Wiring the LNL-1300 (Wiegand)


DATA/D0

VO

LED

BZR

CLK/D1

GND

NC+DC-DC

NCGREEN

REDNC

NC

DATA 1

DATA 0

Back of Reader

NCDATA 1DATA 0NCNC

To 12VDC

NC

RED

GREEN

Tie to DC-

TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand / Prox2. Keypad = Eight Bit Output Keypads3. LED Mode = 1 or 2-WIRE LED CONTROL100 revision 1

Alternative Reader Wiring Guide16.14.2 Wiring the LNL-1320 (Wiegand)


NC+DC-DC

NCGREEN

REDNC

NC

DATA/D0

VO

LEDBZR

CLK/D1

GND

DATA 1

DATA 0

Back of Reader

NCDATA 1DATA 0NCNC

To 12VDC

NC

RED

GREEN

Tie to DC-

1. Reader Type = Wiegand / Prox2. Keypad = Eight Bit Output Keypads3. LED Mode = 1 or 2-WIRE LED CONTROL

TYPICAL SOFTWARE SETTINGSrevision 1 101

HID Readers16.14.3 Wiring the LNL-1300 (OSDP)


Series 2

DATA/D0

VO

LED

BZR

CLK/D1

GND

NC+DC-DC

NCNC

NCNC

GPIO1

GPIO1

GPIO2

Back of Reader

NCNCNCNCNC

To 12VDC

GPIO2

Tie to DC-


1. Reader Type = OSDP Protocol2. Keypad = Eight Bit Output Keypads3. LED Mode = OSDP LCD Reader102 revision 1

Alternative Reader Wiring Guide16.14.4 Wiring the LNL-1320 (OSDP)

16.15. HID MIFARE Format Secure 6075 Reader

The reader operates at 9 -16 VDC. The average current draw is 15mA/75mA.


Series 2NC

+DC-DC

NCNC

NCNC

GPIO1

DATA/D0

VO

LEDBZR

CLK/D1

GND

GPIO1

GPIO2

Back of Reader

NCNCNCNCNC

To 12VDC

GPIO2

Tie to DC-

TYPICAL SOFTWARE SETTINGS1. Reader Type = OSDP Protocol2. Keypad = Eight Bit Output Keypads3. LED Mode = OSDP LCD Readerrevision 1 103


Brown

White

Green

Red

Black

DATA/D0

VO

LED

BZR

CLK/D1

GND

Tie to Earth Ground


TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROL104 revision 1


16.16. HID OSDP Readers

Models 6100BKP through 6181BKP are supported. To use OSDP readers with OnGuard, version 5.12.110 or higher is required. Only Series 2 reader ports offer OSDP support.

Reader 1

VO

LEDBZR

CLK/D1

DATA/D0GND

Brown

White

Green

Red

Black

Tie to Earth Ground


TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROLrevision 1 105


Series 2 Single Reader Interface Module

DATA/D0

VO

LED

BZR

CLK/D1

GND

NC+DC-DC

NCNC

NCNC

GPIO1

GPIO1

GPIO2

Back of Reader

NCNCNCNCNC

To 12VDC

GPIO2

Tie to DC-

Not UsedNot Used

Not used for 6171/6181

TYPICAL SOFTWARE SETTINGS1. Reader Type = OSDP Protocol2. LED Mode = OSDP Reader for all except 6171 and 6181, OSDP LCD Reader for 6171, and 6181106 revision 1


16.17. SmartID/SmartTRANS Models S10/SK10, SP10/SPK10

The following diagrams show wiring for Data 1/Data 0. If you are using Clock/Data, the wiring for the two leads connected at 3 and 4 on the reader should be reversed.

Intelligent Dual Reader Controller/Series 2 Dual Reader Interface Module

NC+DC-DC

NCNC

NCNC

GPIO1

DATA/D0

VO

LEDBZR

CLK/D1

GND

GPIO1

GPIO2

Back of Reader

NCNCNCNCNC

To 12VDC

GPIO2

Tie to DC-

Not used for 6171/6181

Not UsedNot Used

TYPICAL SOFTWARE SETTINGS1. Reader Type = OSDP Protocol2. LED Mode = OSDP Reader for all except 6171 and 6181, OSDP LCD Reader for 6171 and 6181revision 1 107



VO

LED

BZR

CLK/D1

DATA/D0

GND


1. Reader Type = WIEGAND/PROX2. LED Mode = 2-WIRE LED CONTROL

Connector from reader

(1)

(7)

(6)

(5)

(4)(3)

(2)

Green LED

Red LED

Clock/D0

Data/D1

Do not connect

Do not connect

(8)

GroundPower

(5-12 VDC)108 revision 1


Reader 1

VO

LED

BZR

CLK/D1

DATA/D0

GND


Connector from reader

(1)

(7)

(6)

(5)

(4)(3)

(2)

Green LED

Red LED

Clock/D0

Data/D1

Do not connect

Do not connect


1. Reader Type = WIEGAND/PROX2. LED Mode = 2-WIRE LED CONTROL

(8)

GroundPower (5-12 VDC)revision 1 109

HID Readers110 revision 1

Alternative Reader Wiring Guide17. IDH Max

IDH Max readers include all door components a reader device, lock set, door contact, and request to exit sensors.

17.1. IDH Max Door Readers

Use the following diagrams to wire Single/Dual Reader Interface Modules and IDH Max readers.revision 1 111

IDH Max17.1.1 Wiring the LNL-1300

B AJ3

U1

J4

SINGLE READER INTERFACE MODULE

NCCNONONCC

+12VGNDI2-I2+I1+

I1+ 1 2 3 4 5 6 7 8

J2

GNDBZRLED

CLK/D1DAT/D0

+12VTR+TR-SG

CP

NCN

CG

ND

BPR

GR

NRE

DD

1D0

STK

RQ E

DS

LS

1

Black

BrownWhiteGreen

To 12VDC

Ora

nge

Gre

en

Red

Bla

ck

Off

On

TYPICAL SOFTWARE SETTINGS 1. Reader Type = Dependant on Model WIEGAND/PROX HID Reader/iClass ALL OTHER READERS Mag Reader 2. Keypad = NO KEYPAD 3. LED Mode = 1-Wire LED Control

IDH MAX PANEL INTERFACE

12V GND COM+ COM- 12V GND112 revision 1


DUAL READER INTERFACE MODULE

NCC

NO

IN 2

IN 1

GND

BZRLED

CLK/D1DAT/D0

+12VC

PN

CN

CG

ND

BPR

GR

NR

ED

D1

D0

STK

RQ E

DSLS

12V GND COM+ COM-12V GND

1

To 12VDC

Ora

nge

Gre

en

Red

Blac

k

Off

On

TYPICAL SOFTWARE SETTINGS 1. Reader Type = Dependant on Model WIEGAND/PROX HID Reader/iClass ALL OTHER READERS Mag Reader 2. Keypad = NO KEYPAD 3. LED Mode = 1-Wire LED Control

IDH MAX PANEL INTERFACE

NCC

NO

Rea

der 1

RLY

1 R

LY 2revision 1 113

IDH Max114 revision 1

Alternative Reader Wiring Guide18. ID Solutions Readers

Use the following diagrams to wire Single/Dual Reader Interface Modules and ID Solutions readers.

18.1. ID Solutions Model 8030/8035 Bar Code Reader



Red - DC Input

Black - Supply Ground

White - Data 1/Clock

Green - Data 0/Data

Brown - LED Control Input

ID SolutionsBar Code Reader,Model 8030/8035

GND

12 V Power Supply


1. Reader Type = All other readers2. No keypad

GND

BZR

LED

CLK/D1

DAT/D0

+12V

TR+

TR-

SGrevision 1 115

ID Solutions Readers18.1.2 Wiring the LNL-1320

Red - DC Input

Black - Supply Ground

White - Data 1/Clock

Green - Data 0/Data

Brown - LED Control Input

REA

DER

1R

EAD

ER 2

VO

LED

BZR

D1/CLK

D0/DATA

GND


VO

LED

BZR

D1/CLK

D0/DATA

GND

ID SolutionsBar Code Reader,Model 8030/8035

TYPICAL SOFTWARE SETTINGS1. Reader Type = All other readers2. No keypad3. Use the 1320 in Unregulated Mode (jumper J2)116 revision 1

Alternative Reader Wiring Guide19. Infographics Readers

Use the following diagrams to wire Single/Dual Reader Interface Modules and Infographics readers.

19.1. Infographics Reader OTD-60


Bla

ck -

Yel

low

LE

D (n

ot u

sed)


1. Grey - 0 Volts

Brown - Reader Clock

Yellow - Reader Data

4. Green - +5 Volts

Red - Green LED

InfographicsRead

Alt Readers

Documents

Transcript of Alt Readers