PERPETUAAlternative Reader Wiring L INNOVATION
Guide
Lenel OnGuard 2010 Alternative Reader Wiring Guide, product version 6.4This guide is item number DOC-601, revision 1.029, October 2010Copyright 1997-2010 Lenel Systems International, Inc. Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Lenel Systems International, Inc.Non-English versions of Lenel documents are offered as a service to our global audiences. We have attempted to provide an accurate translation of the text, but the official text is the English text, and any differences in the translation are not binding and have no legal effect.The software described in this document is furnished under a license agreement and may only be used in accordance with the terms of that agreement. Lenel and OnGuard are registered trademarks of Lenel Systems International, Inc. Microsoft, Windows, Windows Server, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Integral and FlashPoint are trademarks of Integral Technologies, Inc. Crystal Reports for Windows is a trademark of Crystal Computer Services, Inc. Oracle is a registered trademark of Oracle Corporation. Other product names mentioned in this User Guide may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Portions of this product were created using LEADTOOLS 1991-2010 LEAD Technologies, Inc. ALL RIGHTS RESERVED.OnGuard includes ImageStream Graphic Filters. Copyright 1991-2010 Inso Corporation. All rights reserved. ImageStream Graphic Filters and ImageStream are registered trademarks of Inso Corporation.WarrantyLenel warrants that the product is free from defects in material and workmanship under normal use and service with proper maintenance for one year from the date of factory shipment. Lenel assumes no responsibility for products damaged by improper handling, misuse, neglect, improper installation, over-voltages, repair, alteration, or accident. This warranty is limited to the repair or replacement of the defective unit. In no event shall Lenel be liable for loss of use or consequential damages of any kind, however occasioned.There are no expressed warranties other than those set forth herein. Warranty espressly excludes third party additions, deletions and/or upgrades to this product, including those contained herein. Lenel does not make, nor intends, nor does it authorize any agent or representative to make any other warranties or implied warranties, and expressly excludes and disclaims all implied warranties of merchantability or fitness for a particular purpose.Returned units are repaired or replaced from a stock of reconditioned units. All returns must be accompanied by a return authorization number (RMA) obtained from the Lenel customer service department prior to returning or exchanging any product. The RMA number must appear on the outside of the shipping box and on the packing slip. Any items returned without an RMA number will not be accepted and will be returned at the customers expense. All returns must have transportation, insurance, and custom brokers fees prepaid.
LiabilityIt is expressly understood and agreed that the interface should only be used to control exits from areas where an alternative method for exit is available. This product is not intended for, nor is rated for operation in life-critical control applications. Lenel is not liable under any circumstances for loss or damage caused by or partially caused by the misapplication or malfunction of the product. Lenels liability does not extend beyond the purchase price of the product.
Alternative Reader Wiring GuideTable of Contents
Access Readers ...................................................................7
1. UL Evaluated Readers ........................................................................... 9
2. AIT Readers ........................................................................................... 92.1. AIT Reader #L-TR200 ................................................................... 9
3. AWID Readers ..................................................................................... 133.1. AWID Sentinel Prox MR-1824 ..................................................... 133.2. AWID Sentinel-Prox SP-6820, SR-2400, and MM-6800 ............. 153.3. AWID Prox with Keypad (KP-6840) ............................................. 163.4. AWID Sentinel-Prox RKP-4600 ................................................... 183.5. AWID Sentinel-Prox LR-911 ........................................................ 19
4. BAI Barcode Readers .......................................................................... 214.1. BAI Barcode Reader #BA-200 .................................................... 21
5. Banque-Tec Readers ........................................................................... 235.1. Smart Card Reader (Models BT815 and BT900/818) ................. 23
6. Baran Tec Keypads ............................................................................. 256.1. LNL826S121NN 8-bit Output Keypad Reader ............................ 256.2. Baran Tec Everswitch Proximity Reader Plus Keypad ................ 28
7. Bewator Readers ................................................................................. 317.1. Remote Card Reader Model BC18 ............................................. 31
8. Casi-Rusco Prox Readers ................................................................... 338.1. Casi-Rusco 94x, 97x Prox Readers ............................................ 338.2. Reader (Wiegand) Operation ...................................................... 358.3. Casi-Rusco 940-W Prox Lite (F/2F Mode) .................................. 368.4. Configuration for Casi-Rusco Readers ........................................ 388.5. Reader (F/2F Mode) Operation ................................................... 40
9. CEIA Readers ...................................................................................... 419.1. CEIA Freedom Reader with Keypad (Prox) ................................ 419.2. CEIA Freedom Reader (Output Protocol Clock/Data) ................. 42
10. Checkpoint Systems Readers ........................................................... 4510.1. Mirage II Readers ...................................................................... 45revision 1 3
Table of Contents10.2. Checkpoint Reader Model SN-MSC 16147 ............................... 4710.3. Mirage Proximity Reader B ....................................................... 49
11. Codeguard Series II/III ....................................................................... 5111.1. Secure Keypad Reader ............................................................. 51
12. Cross Match Readers ........................................................................ 5712.1. Cross Match 900xxx TWIC Readers ......................................... 57
13. Deister Electronics ............................................................................. 6113.1. Smart Card Reader Model PRM 5M, PRX 5 HSF ..................... 6113.2. Reader Model PRL5/2 KPL5/2 .................................................. 62
14. Dorado Readers ................................................................................ 6514.1. Dorado Reader Model 644 ........................................................ 6514.2. Dorado Reader Model 780 ........................................................ 6714.3. Dorado Reader Model 611 ........................................................ 6914.4. Dorado Elevator Reader 570 ..................................................... 6914.5. Dorado 230/240 Combination Readers ..................................... 71
15. Essex Keypads .................................................................................. 7515.1. Essex Keypad Reader #KTP-16212SLI .................................... 7515.2. Essex Keypad Reader #KTP-163SN ........................................ 77
16. HID Readers ...................................................................................... 7916.1. HID ProxPro .............................................................................. 7916.2. HID MaxiProx 5370 A-1 ............................................................. 8116.3. HID MaxiProx 5370/5375AGN00 .............................................. 8216.4. Hughes MiniProx ....................................................................... 8316.5. Classic, EPIC Swipe and Pinpad Wiegand Readers ................. 8516.6. ProxPoint Readers .................................................................... 8616.7. ProxPro II .................................................................................. 8716.8. iClass Reader/Encoder ............................................................. 8916.9. iClass Reader ............................................................................ 9116.10. iClass RK-40 ........................................................................... 9216.11. EntryProx 4045-905 ................................................................ 9416.12. SensorKey Reader .................................................................. 9616.13. HID MIFARE 6055 ................................................................... 9816.14. HID LCD and bioCLASS Readers (RWKL550/RWKLB575) . 10016.15. HID MIFARE Format Secure 6075 Reader ........................... 10316.16. HID OSDP Readers .............................................................. 10516.17. SmartID/SmartTRANS Models S10/SK10, SP10/SPK10 ...... 1074 revision 1
Alternative Reader Wiring Guide17. IDH Max ........................................................................................... 11117.1. IDH Max Door Readers ........................................................... 111
18. ID Solutions Readers ....................................................................... 11518.1. ID Solutions Model 8030/8035 Bar Code Reader ................... 115
19. Infographics Readers ....................................................................... 11719.1. Infographics Reader OTD-60 .................................................. 117
20. Integrated Engineering Readers ...................................................... 11920.1. Integrated Engineering PX007 Mifare Reader ........................ 11920.2. Desfire Reader ........................................................................ 12220.3. SmartID Readers ..................................................................... 123
21. Keri Systems Readers ..................................................................... 12721.1. Cascade and Sierra Readers (P-300, P-400, P-500, P-600 with
Keypad, P-700) .............................................................................. 127
22. Magtek Readers .............................................................................. 12922.1. Magtek 101-Millimeter Swipe Reader (Model 2105002) ......... 129
23. Mifare Readers ................................................................................ 13123.1. Mifare Model LA-WIW-PROXKEY-M ...................................... 13123.2. Iolan Reader Model LA-XXW-PRXKY-MX 1050-4021-092 ..... 133
24. Motorola Indala Readers ................................................................. 13524.1. Indala Readers ASR-120, ASR-122 ........................................ 13524.2. Indala Readers ASR-503, ASR-505, ASR-110, ASR-112 ....... 13724.3. Indala Readers ASR-103, ASR-105, ASR-120, ASR-122, ASR-
124, ASR-136 ................................................................................ 13924.4. Indala Reader ARK-501 .......................................................... 14324.5. Indala Readers ASR-500, ASR-501, ASR-503, ASR-505, ASR-
110 ................................................................................................. 14524.6. Motorola BiStatix Prox Reader (BXR-610) .............................. 14724.7. Indala EM4525F Reader ......................................................... 14824.8. Motorola FlexPass Readers .................................................... 149
25. Nedap Readers ................................................................................ 15125.1. Nedap Transit Readers ........................................................... 151
26. Northern Readers ............................................................................ 15526.1. Northern BR-7 Barcode Reader .............................................. 155
27. Schlage Keypads ............................................................................. 15727.1. Schlage SERIII-W Scramble Keypad ...................................... 157
28. Secura Key Readers ........................................................................ 163revision 1 5
Table of Contents28.1. e-Tag Prox Reader #ASSY 2014040 ...................................... 16328.2. Touch Card Reader (TC-100) ................................................. 16528.3. Touch Card SK-028W Barium Ferrite Reader ......................... 167
29. Synergistics Readers ....................................................................... 16929.1. SR1054FL Swipe Card Reader ............................................... 16929.2. SR1058SLE Swipe Card Reader ............................................ 171
30. Texas Instruments Readers ............................................................. 17330.1. TI S6410 Wall Plate/S6420 Mullion Reader ............................ 173
31. XCeedID Readers ............................................................................ 17531.1. XCeedID ISO-X Reader .......................................................... 175
Index ........................................................................................................... 1796 revision 1
ACCESS READERS
Alternative Reader Wiring Guide1. UL Evaluated Readers
For more details on which readers are certified for UL Listed installations, refer to the Hardware Installation Guide, DOC-600, or the NGP Hardware Installation Guide, 55-6000E.
2. AIT Readers
2.1. AIT Reader #L-TR200
AIT readers are used for asset tracking. The reader/antenna is connected to a Wiegand data converter and attached directly to a reader interface module. The Wiegand converter changes the data from RS-485 to a standard Wiegand data string. This allows the software to function with these readers and cards. The reader can effectively read the assets up to 45 feet from the reader using asset tags L-TG100 and L-TG200.revision 1 9
AIT Readers2.1.1 Wiring the LNL-1300
AIT
Aut
omat
ed Id
entif
icat
ion
Tech
nolo
gies
+12v
GND
Rx
+12 vGND
Red LEDGrn LED
Data 00Data 01
Wiegand Data Converter
+12 v
LED (Red LED)BZR (Green LED)
Data 01Data 00
GND
RJ45TerminatingConnector
Wiring to Single Reader Interface Module
TokenIn
Token Return
Tied
Toge
ther
RJ45Connector
Pin 1
Typical Software Settings
Reader Type = Wiegand/ProxKeypad = No KeypadLED Mode = 2-Wire LED Support
Pin Outs for RS-485 ConnectionPin 8 = GroundPin 7 = Data TxPin 6 = Token InPin 5 = +12 v DCPin 4 = Token Return
Pin 2Pin 3Pin 4Pin 5Pin 6Pin 7Pin 8
AIT Reader# L-TR20010 revision 1
Alternative Reader Wiring Guide2.1.2 Wiring the LNL-1320
AIT
Auto
mat
ed Id
entif
icat
ion
Tech
nolo
gies
+12V
GND
Rx
+12VGND
RedGn
Data 00Data 01
Wiegand Data Converter# L-W1100
+12 vLED (Red LED)BZR (Green LED)Data 01Data 00GND
RJ45TerminatingConnector
Wiring to Dual Reader Interface Module
TokenIn
TokenReturn
Tied
Toge
ther
RJ45Connector
+5V
D0D0-D1
D1-
TxGND
+5V
Yel
C2NO2NC2C1
NO1NC1
W1W0n/u
AIT Reader# L-TR200
Jumper SettingsJ1 - 4 & 5 offJ2 - 1 & 2 off/3 onJ3 - 1 & 2 OnJ4 - 232 pins 1 & 2
Typical Software Settings
Reader Type = Wiegand/ProxKeypad = No KeypadLED Mode = 2-Wire LED Support
Pin Outs for RS485 Connection
Pin 8 = GroundPin 7 = Data TxPin 6 = Token InPin 5 = +12 VDCPin 4 = Token Return
Pin 1Pin 2Pin 3Pin 4Pin 5Pin 6Pin 7Pin 8revision 1 11
AIT Readers12 revision 1
Alternative Reader Wiring Guide3. AWID Readers
Use the following diagrams to wire (single wire LED control) Single/Dual Reader Interface Modules and AWID Sentinel readers.
If a Sentinel Prox reader is disconnected from the power supply and then reconnected, the readers will not read the initial card presented. Subsequent cards will be read as usual.
3.1. AWID Sentinel Prox MR-1824
This reader has an input current ranging from 250 to 650 mA. The reader distance also varies according to the current, from 15 to 25 inches. Due to this input current, the reader will need to be run off a dedicated power supply.
3.1.1 Wiring the LNL-1300
AWID
12 V
GND
Power Supply
VO
LED
BZR
CLK/D1
DATA/D0
GND
The negative current from the power supplies must be tied together
Brown
Yellow
White
Green
Red
Black
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL
Single Reader Interface Module
AWID Sentinel Prox MR-1824
Tie to Earth Groundrevision 1 13
AWID Readers3.1.2 Wiring the LNL-1320
AWID Sentinel Prox MR-1824R
eader 1AWID
12 V
GND
Power Supply
VO
LED
BZR
CLK/D1
DATA/D0
GND
The negative current from the power supplies must be tied together
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL
Brown
Yellow
White
Green
Red
Black
Dual Reader Interface Module
Tie to Earth Ground14 revision 1
Alternative Reader Wiring Guide3.2. AWID Sentinel-Prox SP-6820, SR-2400, and MM-6800
The following readers do not require a dedicated power supply. The current requirements for these readers range from 40-120 mA. This means that the readers can be powered from the reader interface modules. It is important to make sure that the dual reader interface module is set to UNREGULATED POWER MODE (jumper J2). This will allow the maximum amount of current for the readers.
3.2.1 Wiring the LNL-1300
3.2.2 Wiring the LNL-1320
AWID
Brown
Yellow
White
Green
Red
Black
VO
LED
BZR
CLK/D1
DATA/D0
GND
AWID Sentinel-Prox SP-6820,SR-2400, and MM-6800
Single Reader Interface Module
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL
Tie to EarthGround
AWID Reader 1
VO
LED
BZR
CLK/D1
DATA/D0
GND
Brown
Yellow
White
Green
Red
Black
Dual Reader Interface Module
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL
Tie to EarthGroundrevision 1 15
AWID Readers3.3. AWID Prox with Keypad (KP-6840)
(The reader must be KP-6840 REV C-8 for proper functionality)
The reader operates at 5-12 VDC and has a current draw requirement of 50-120 mA. The reader can be powered directly from the Dual Reader Interface. The keypad uses an 8-Bit output burst and meets all Lenel functionality requirements. The reader uses a single wire LED control and the LED functionality also meets all Lenel specifications.
3.3.1 Wiring the LNL-1300
AWID
1 2 3
4 5 6
7 8 9
0 #*Single Reader Interface Module
Brown
Yellow
White
Green
Red
Black
VO
LED
BZR
CLK/D1
DATA/D0
GND
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = 8-Bit Ouput3. LED Mode = 1-WIRE LED CONTROL
Tie toEarth
Ground16 revision 1
Alternative Reader Wiring Guide3.3.2 Wiring the LNL-1320
Reader 1
VO
LED
BZR
CLK/D1
DATA/D0
GND
Brown
Yellow
White
Green
Red
Black
AWID
1 2 3
4 5 6
7 8 9
0 #*
Dual Reader Interface Module
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = 8-Bit Ouput3. LED Mode = 1-WIRE LED CONTROL
Tie to EarthGroundrevision 1 17
AWID Readers3.4. AWID Sentinel-Prox RKP-4600
This reader is a radio-frequency proximity reader with a virtually indestructible integrated keypad for access control systems. The reader consists of a 12-key piezoelectric keypad, transmit/receive antenna, and reader electronics, in a slim plastic housing. The reader electronics are potted with epoxy resin to protect against the environment. The reader may be mounted on a single-gang electrical utility box, or on any surface (wall, cabinet, etc.).
3.4.1 Wiring the RKP-4600 Reader18 revision 1
Alternative Reader Wiring Guide3.5. AWID Sentinel-Prox LR-911
The LR-911 requires an alternate power source of 5-15 VDC and has a current requirement of 1.5A. There are no LED's on the reader (optional). The reader has a read range of up to 11 feet. See diagram below for proper wiring and setup.
3.5.1 Wiring the LNL-1300
* The LR-911 feature a cone shaped read zone. Theoptimal read zone is a circular cone that is at a 45 degreeangle from the edges of the reader and extends out to 11feet away from the center of the reader. Cards can beread accurately if presented to the reader within this range.
Up to 11' fromreader
12v
GNDPower Supply
Red
Black
VO
LED
BZR
CLK/D1
DATA/D0
GND
Yellow*Allows LR-911 Read Cylcling
Green
White
Blue
Single Reader Interface Module
AWID
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = No-LED Controlrevision 1 19
AWID Readers3.5.2 Wiring the LNL-1320
Dual Reader Interface Module
AWID
Reader 1
12v
GNDPower Supply
VO
LED
BZR
CLK/D1
DATA/D0
GND
Red
Black
Yellow
*Allows LR-911 Read Cylcling
Green
White
Blue
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = No-LED Control20 revision 1
Alternative Reader Wiring Guide4. BAI Barcode Readers
The BAI (BA-200) Barcode reader supports an Wiegand output format of 26, 30, and 31 bits. The reader will support the following barcode formats: 10 digit interleave 2 of 5 barcode, 8 digit interleave 2 of 5 barcode, proprietary format called AFC, and 5 character code 39 barcode. For test purposes, there were no setup modifications made. We used all pre-set factory default settings. There are two LED's on the outside of the reader. The amber light shows that there is power connected to the reader, and the green light will come on when there is a valid card read. The current firmware revision is 1006.
4.1. BAI Barcode Reader #BA-200
4.1.1 Wiring the LNL-1300
B A IBarcode Automation Inc.
Wiegand 0Wiegand 1
Ground
Ground
Data
Clock
Single Reader Interface Module
24 VDCPower Supply
Ground+24 VDC
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROLrevision 1 21
BAI Barcode Readers4.1.2 Wiring the LNL-1320
B A IBarcode Automation Inc.
Wiegand 0Wiegand 1
Ground
Gro
und
Dat
aC
lockDual Reader Interface Module
24 VDCPower Supply
Ground+24 VDC
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL22 revision 1
Alternative Reader Wiring Guide5. Banque-Tec Readers
5.1. Smart Card Reader (Models BT815 and BT900/818)
The smart card reader operates at 12 VDC and communicates with a standard Wiegand output. It uses a single wire LED control. Follow the drawing below to connect the reader to the reader interface module.
5.1.1 Wiring the LNL-1300
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL
Blue
White
Green
Yellow
Red
Black
VO
LED
BZR
CLK/D1
DATA/D0
GND
BANQUE-TECSingle Reader Interface Modulerevision 1 23
Banque-Tec Readers5.1.2 Wiring the LNL-1320
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL
BANQUE-TEC
Reader 1
VO
LED
BZR
CLK/D1
DATA/D0
GND
Blue
White
Green
Red
Black
Dual Reader Interface Module
Yellow24 revision 1
Alternative Reader Wiring Guide6. Baran Tec Keypads
These keypads are available in two styles: 3 x 4 keypads (part number LNL834S121NN) and 2 x 6 keypads (part number LNL826S121NN).
6.1. LNL826S121NN 8-bit Output Keypad Reader
The reader requires a 12-28 VDC power source and has a current draw of 30 mA. Therefore, the reader can be powered directly from either of the reader interface modules.
The wiring diagrams describe wiring if the keypad is being connected in line with another Lenel supported reader and the LED support for the keypad is being used. The keypad features a 2-Wire LED configuration. If the LED support for this keypad is not being used, omit the connections for those two wires. The reader is using a standard 8-bit output format.revision 1 25
Baran Tec KeypadsImportant: Make sure that the LED control is connected for only one reader. Both reader LEDs can not be connected at the same time.
6.1.1 Wiring the LNL-1300
The wiring diagram has the 2 x 6 keypad depicted. A 3 x 4 keypad may also be used.
1
3
5
7
9
*
2
4
6
8
0
#Brown
Yellow
White
Green
Red
Black
VO
LED
BZR
CLK/D1
DATA/D0
GND
H I D
HID ProxPoint Reader
Single Reader Interface Module
GND - Black
Data 1 - White
Data 0 - Green
5-12VDC - Red
TYPICAL SOFTWARE SETTINGS
1. Keypad = 8-Bit Output2. LED Mode = 2-WIRE LED CONTROL3. Wiegand/Prox data type26 revision 1
Alternative Reader Wiring Guide6.1.2 Wiring the LNL-1320
The wiring diagram has the 2 x 6 keypad depicted. A 3 x 4 keypad may also be used.
Brown
Yellow
White
Green
Red
Black
H I D
HID ProxPoint Reader
GND - Black
Data 1 - White
Data 0 - Green
5-12VDC - Red
Reader 1
VO
LED
BZR
CLK/D1
DATA/D0
GND
Dual Reader Interface Module
TYPICAL SOFTWARE SETTINGS
1. Keypad = 8-Bit Output2. LED Mode = 2-WIRE LED CONTROL3. Wiegand/Prox data type
1
3
5
7
9
*
2
4
6
8
0
#revision 1 27
Baran Tec Keypads6.2. Baran Tec Everswitch Proximity Reader Plus Keypad
The BaranTec Everswitch reader operates at 5-12 VDC. The maximum current draw is 150 mA.
6.2.1 Wiring the LNL-1300
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = 8-bit Output Keypad3. LED Mode = 1-WIRE LED CONTROL
BrownWhite
Green
Red
Black
Single ReaderInterface Module
DATA/D0
VO
LED
BZR
CLK/D1
GND
Tie to EarthGround
*
4
# 9 0
7 8
5 6
3
1 2
1k,1%
Supervision: Not Supervised, Normally Open
Gray
Tamper Input28 revision 1
Alternative Reader Wiring Guide6.2.2 Wiring the LNL-1320
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = 8-bit Output Keypad3. LED Mode = 1-WIRE LED CONTROL
Dual Reader InterfaceModule
Reader 1
VOLEDBZR
CLK/D1
DATA/D0GND
Brown
White
Green
Red
Black
Tie to EarthGround
*
4
# 9 0
7 8
5 6
3
1 2
1k,1%
Supervision: Not Supervised, Normally Open
Tamper Input
Grayrevision 1 29
Baran Tec Keypads30 revision 1
Alternative Reader Wiring Guide7. Bewator Readers
7.1. Remote Card Reader Model BC18
The reader does not require a separate power supply when being connected to the Dual Reader Interface Module. However, the reader will need an alternate 5 VDC power connection if it is connected to a Single Reader Interface Module. The recommended draw is 40 mA and the reader needs to be connected to 5 VDC. Also, be sure to set up Jumper J2 for REGULATED power mode. J4 should be configured for 5 VDC. Recommended operating temperature: -10 to 55 C.
7.1.1 Wiring the LNL-1300
Green
Yellow
Grey
White
Blue
VO
LED
BZR
CLK/D1
DATA/D0
GND
Single Reader Interface Module
5 VDCPowersupply +
-
BC18
BE
WA
TOR
TYPICAL SOFTWARE SETTINGS1. Reader Type = ALL OTHER READERS2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROLrevision 1 31
Bewator Readers7.1.2 Wiring the LNL-1320
Reader 1
Reader 2
VO
LED
BZR
CLK/D1
DATA/D0
GND
Green
Yellow
Grey
White
Blue
Dual Reader Interface Module
BC18
BEW
ATO
R
TYPICAL SOFTWARE SETTINGS1. Reader Type = ALL OTHER READERS2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL32 revision 1
Alternative Reader Wiring Guide8. Casi-Rusco Prox Readers
8.1. Casi-Rusco 94x, 97x Prox Readers
This reader operates at 12 VDC. The average current draw with Power Level set to Low (SW-2) is 75 mA. See manual for volt and current recommendations.
8.1.1 Wiring the LNL-1300
Brown (Green LED )
Blue (Red LED)
White (D1)
Green (D0)
Red (+12VDC)
Black (Ground )
Single Reader Interface Module
DATA/D0
VO
LED
BZR
CLK/D1
GND
Tie to Earth Ground
CASI -RUSCO
R Y G
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = 8 bit (if used)3. LED Mode = 2-WIRE LED CONTROLrevision 1 33
Casi-Rusco Prox Readers8.1.2 Wiring the LNL-1320
VO
LED
BZR
D1/CLK
D0/DATA
GND
VO
LED
BZR
D1/CLK
D0/DATA
GND
REA
DER
1R
EAD
ER
2
Dual Reader Interface Module
CASI-RUSCO
R Y G
Black (Ground )
Blue (Red LED)
Brown (Green LED )Red (+12VDC)
Green (D0)White (D1)
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = 8 bit (if used)3. LED Mode = 2-WIRE LED CONTROL34 revision 1
Alternative Reader Wiring Guide8.1.3 Set the 94x/97x DIP Switches
Casi-Rusco 94x, 97x DIP switch settings
8.2. Reader (Wiegand) Operation
Three LED lights across the top of the Casi-Rusco prox readers signify the mode of operation.
Status Indicators
AUDIO RED LED YELLOW LED
GREEN LED
LED Operation:
Locked --- Solid light Dim light Dim light
Card Only --- Slow-blinking light Dim light Dim light
Card or PIN --- Slow-blinking light Dim light Slow-blinking light
Card and PIN --- Slow-blinking light Dim light Dim light
Unlocked --- Slow-blinking light Dim light No light
Facility Code Only --- Slow-blinking light Dim light Dim light
Beeper Operation:
1234
ON OFF
Gray Area represents switch position
5678
ON OFF
DIP Switch setup for reader
Wire connector on
back of reader
SW-2
SW-3
Switch 5, 6 = Off WiegandSwitch 7 = On, Switch 8 = Off Beeper Sound Low
Reader (Backplate Removed)
Switches 1,4 = Off, Switches 2,3 = On -Power Level = Lowrevision 1 35
Casi-Rusco Prox Readers8.3. Casi-Rusco 940-W Prox Lite (F/2F Mode)
The Dual Reader Interface Module can support Casi-Rusco readers in the F/2F mode of operation. This is only supported on Dual Reader Interface Modules with firmware 1.13 or higher. The 940-W Prox Lite is the 94x or 97x proximity reader in OnGuard, used in F/2F mode.
This reader operates at 12 VDC. The average current draw with Power Level set to Low (SW-2) is 75 mA. See manual for volt and current recommendations.
Access Granted Two beeps No light for 5 seconds
Blinks once Blinks 5 times
Access Denied Three beeps Stops blinking for 5 seconds
Blinks once Dim light
Invalid Badge Single beep Blinks 6 times --- ---
In a Card and PIN Configuration:
Access Granted (once a valid PIN is entered, the door opens)
Single beep --- Dim light Dim light
Access Denied Single beep If no PIN is entered, the red LED blinks 6 times.
Dim light Dim light
Status Indicators
AUDIO RED LED YELLOW LED
GREEN LED36 revision 1
Alternative Reader Wiring Guide8.3.1 Wiring the LNL-1320
VO
LED
BZR
D1/CLK
D0/DATA
GND
VO
LED
BZR
D1/CLK
D0/DATA
GND
REA
DER
1R
EAD
ER
2
Dual Reader Interface Module
CASI-RUSCO
R Y G
Black (Ground )
Blue (Red LED)
Brown (Green LED )Red (+12VDC)
White (D1)
TYPICAL SOFTWARE SETTINGS1. Reader Type = F/2F format2. Keypad = NO KEYPAD3. LED Mode = 2-WIRE LED CONTROLrevision 1 37
Casi-Rusco Prox Readers8.3.2 Set the 940w DIP Switches
Casi-Rusco 940w DIP switch settings
8.4. Configuration for Casi-Rusco Readers
The Casi-Rusco readers can be configured for Wiegand/Prox or F/2F format.
1234
ON OFF
Gray Area represents switch position
5678
ON OFF
DIP Switch setup for reader
Wire connector on
back of reader
SW-2
SW-3
Switch 5 = On, 6 = Off F/2FSwitch 7 = On, Switch 8 = Off Beeper Sound Low
Reader (Backplate Removed)
Switches 1,4 = Off, Switches 2,3 = On -Power Level = Low38 revision 1
Alternative Reader Wiring Guide8.4.1 Casi-Rusco Readers as a Wiegand/Prox Type
In order to configure the software correctly, refer to the following screenshot. This screen can be launched by selecting Card Formats from the Administration menu in either ID CredentialCenter or System Administration.
The configuration for the Casi-Rusco within the access control system is as follows:
Reader Type Wiegand/Prox format
Keypad Type 8 bit (if keypad is used)
Reader Settings 2-wire LED control
8.4.2 Casi-Rusco Readers as a Dual Reader Interface in F/2F Format
The configuration for this reader in F/2F mode is different. Refer to the following screenshot.revision 1 39
Casi-Rusco Prox ReadersThe default configuration for the Casi-Rusco within the access control system is as follows:
Reader Type Select Dual Interface Rdr 1 (F/2F format) or Dual Interface Rdr 2 (F/2F) format
Keypad Type The keypad type does not apply when using F/2F format
Reader Settings 2-wire LED control
8.5. Reader (F/2F Mode) Operation
Three LED lights across the top of the Casi-Rusco prox readers signify the mode of operation.
Status Indicators
AUDIO RED LED YELLOW LED
GREEN LED
LED Operation:
Locked --- Solid light Dim light Dim light
Card Only --- Slow-blinking light Dim light Dim light
Card or PIN --- --- Dim light Slow-blinking light
Card and PIN --- Slow-blinking light Dim light Dim light
Unlocked --- --- Dim light Slow-blinking light
Facility Code Only --- Slow-blinking light Dim light Dim light
Beeper Operation:
Access Granted Single beep --- --- ---
Access Denied Single beep Blinks 6 times --- ---
Invalid Badge Single beep Blinks 6 times --- ---
In a Card and PIN Configuration:
Access Granted (once a valid PIN is entered, the door opens)
Single beep --- Dim light Dim light
Access Denied Single beep If no PIN is entered, the red LED blinks 6 times.
Dim light Dim light40 revision 1
Alternative Reader Wiring Guide9. CEIA Readers
9.1. CEIA Freedom Reader with Keypad (Prox)
The maximum power rating on the Freedom Reader is between 5-30 VDC. The normal current draw for the reader is 40 mA. The keypad on the reader operates using a 4-bit output. This is not the standard format. This is the only format that is tested and supported by Lenel. The LED functions using single wire LED control. Both the keypad and the LED meet all the requirements for functionality that Lenel requires. Follow the diagrams below to wire the reader properly.
9.1.1 Wiring the LNL-1300
VO
LED
BZR
CLK/D1
DATA/D0
GND
1 32
4 65
7 98
#0*
Single Reader Interface Module
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = 4-Bit Output3. LED Mode = SINGLE WIRE LED CONTROLrevision 1 41
CEIA Readers9.1.2 Wiring the LNL-1320
9.2. CEIA Freedom Reader (Output Protocol Clock/Data)
This reader operates typically on 25 mA, peak 50 mA at 5-30 VDC.
Reader 1
VO
LED
BZR
CLK/D1
DATA/D0
GND
1 32
4 65
7 98
#0*
Connections made to terminal strip on back of reader
Dual Reader Interface Module
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = 4-Bit Output3. LED Mode = SINGLE WIRE LED CONTROL42 revision 1
Alternative Reader Wiring Guide9.2.1 Wiring the LNL-1300
Single Reader Interface Module
Tie to Earth Ground
TYPICAL SOFTWARE SETTINGS
1. Reader Type = All other readers2. Keypad = No Keypad 3. LED Mode = 1 WIRE LED CONTROL DATA/D0
VO
LED
BZR
CLK/D1
GND
Red
Green
WhiteBrown
Blackrevision 1 43
CEIA Readers9.2.2 Wiring the LNL-1320
Dual Reader Interface Module Tie to
Earth Ground
TYPICAL SOFTWARE SETTINGS
1. Reader Type = All other readers2. Keypad = No Keypad 3. LED Mode = 1 WIRE LED CONTROL
DATA/D0
VO
LED
BZR
CLK/D1
GND
Red
Brown
White
GreenBlack44 revision 1
Alternative Reader Wiring Guide10. Checkpoint Systems Readers
Use the following diagrams to wire (single wire LED control) Single/Dual Reader Interface Modules and Checkpoint Systems readers.
10.1. Mirage II Readers
10.1.1 Wiring the LNL-1300
TYPICAL SOFTWARE SETTINGS1. 2-Wire LED Support2. No keypad3. Wiegand/Prox data type
Checkpoint SystemsMirage II Reader
Single Reader Interface Module
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SG
Black - Ground
Brown - LED
White - Data 1
Red - 12 VDC
Green - Data 0revision 1 45
Checkpoint Systems Readers10.1.2 Wiring the LNL-1320
RE
AD
ER
1R
EA
DE
R 2
VO
LED
BZR
D1/CLK
D0/DATA
GND
VO
LED
BZR
D1/CLK
D0/DATA
GND
Dual Reader Interface Module
TYPICAL SOFTWARE SETTINGS1. 2-Wire LED Support2. No keypad3. Wiegand/Prox data type4. Use Unregulated Mode for jumper J2
Red - 12 VDC
Brown - LED
White - Data 1
Green - Data 0
Black - Ground
Checkpoint SystemsMirage II Reader46 revision 1
Alternative Reader Wiring Guide10.2. Checkpoint Reader Model SN-MSC 16147
This Checkpoint reader is operated at 12 VDC and has a current draw of 75 mA.
10.2.1 Wiring the LNL-1300
Single ReaderInterface Module
Checkpoint Reader Model SN-MSC 16147
TYPICAL SOFTWARE SETTINGS
1. Reader Type = Single Interface (Weigand/Prox)2. LED Mode = 2 Wire LED Control
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SG
Checkpoint
Black
White
Green
Red
Brownrevision 1 47
Checkpoint Systems Readers10.2.2 Wiring the LNL-1320
REA
DER
1R
EAD
ER 2
VO
LED
BZR
D1/CLK
D0/DATA
GND
VO
LED
BZR
D1/CLK
D0/DATA
GND
TYPICAL SOFTWARE SETTINGS1. Reader Type = Single Interface (Weigand/Prox)2. LED Mode = 2 Wire LED Control
Dual ReaderInterface Module
Checkpoint
Red
White
Black
Green
Brown
Checkpoint Reader Model SN-MSC 1614748 revision 1
Alternative Reader Wiring Guide10.3. Mirage Proximity Reader B
The Mirage Proximity Reader B is a 33-bit prox reader. It operates at 12 VDC 10%. The average current draw is 50 mA.
10.3.1 Wiring the LNL-1300
White
Green
Red
Black
DATA/D0
VO
LED
BZR
CLK/D1
GND
Tie toEarth
Ground
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROLrevision 1 49
Checkpoint Systems Readers10.3.2 Wiring the LNL-1320
Dual ReaderInterface Module
Reader 1
VO
LEDBZR
CLK/D1
DATA/D0GND
White
Green
Red
Black
Tie toEarth
Ground
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROL50 revision 1
Alternative Reader Wiring Guide11. Codeguard Series II/III
11.1. Secure Keypad Reader
The reader operates at +8 to +12 VDC unregulated. The average current draw is 100 mA (TYP) 180 mA (MAX) with display OFF and 280 mA (TYP) 350 mA (MAX) with display ON.
11.1.1 Set the Mode Dials
`
1 2
543
0E F
8
D
B69
CA 7
`
1 2
543
0E F
8
D
B69
CA 7
`
1 2
543
0E F
8
D
B69
CA 7
Mode Dials in Rear Panel
(Located Behind Rubber Blanking Plug)
Facility Code (Modes 1-6 only, set to 0,0 for modes 7-A)
Operating Mode(See Card Formats)
IMPORTANT: The Facility Code and Operating Mode must be set PRIOR to the installation of the reader.
To Set Facility CodeEach switch is numbered 0 to F, allowing 256 different facility codes to be selected (00 to FF). The switch on the left sets the most-significant digit of the Facility Code, the switch on the right sets the least-significant digit of the code. Disconnect power from the unit when altering the setting of these switches. revision 1 51
Codeguard Series II/III11.1.2 Card Formats
Code Lengths
Mode 0 Supports 1 to 9 digits with a transmitted block length of 40 bits with even/odd parity.
Mode 1 Supports 1 to 4 digits with a transmitted block length of 34 bits.
Mode 2 Supports 1 to 4 digits with a transmitted block length of 26 bits.
Mode 3 Supports 1 to 4 digits with a transmitted block length of 26 bits with even/odd parity.
Mode 4 Supports 5 digits with a transmitted block length of 34 bits.
Mode 5 Supports 5 digits with a transmitted block length of 26 bits.
Mode 6 Supports 5 digits with a transmitted block length of 26 bits with even/odd parity.
Model series
Mode Total number of bits on card
Facility codeStarting bit/Number of bits
Card numberStarting bit/Number of bits
Issue codeStarting bit/Number of bits
Number of even parity bits
Number of odd parity bits
Special
II or III 0 40 1 / 8 9 / 30 0 / 0 20 20 None
II or III 1 34 1 / 8 17 / 16 0 / 0 0 0 None
II or III 2 26 1 / 8 9 / 16 0 / 0 0 0 None
II or III 3 26 1 / 8 9 / 16 0 / 0 13 13 None
II or III 4 34 1 / 8 17 / 16 0 / 0 0 0 None
II or III 5 26 1 / 8 9 / 16 0 / 0 0 0 None
II or III 6 26 1 / 8 9 / 16 0 / 0 13 13 None
III only 7 4-bit keypad emulation, 0-9 codes only
III only 8 8-bit keypad emulation, 0-9 codes only
III only 9 4-bit keypad emulation, 0-9 plus # and * codes transmitted
III only A 8-bit keypad emulation, 0-9 plus # and * codes transmitted52 revision 1
Alternative Reader Wiring Guide11.1.3 Wiring the LNL-1300
TYPICAL SOFTWARE SETTINGS
1. Reader Type = Wiegand / Prox2. Keypad = 4 or 8 Bit Output (see mode)3. LED Mode = 2-WIRE LED CONTROL
DATA/D0VO (No Connection)
LED
BZR
CLK/D1
GND
Single Reader Interface Module
12
34
56
78
Connector Pin Block
Pin 2
Pin 8
Pin 4
Pin 5
Pin 7
Pin 38-12VDC Power
Supply-+revision 1 53
Codeguard Series II/III11.1.4 Wiring the LNL-1320
DATA/D0
LED
BZR
CLK/D1
GND
Dual Reader Interface Module
12
34
56
78
Connector Pin Block
Pin 7
Pin 5
Pin 8
Pin 4
IMPORTANT! This reader cannot be powered from the Dual Reader Interface Module. There must be a common ground between the Power Supply and the Dual Reader Interface Module.
Pin 2 8-12VDC Power Supply
-+Pin 3
VO (No Connection)
TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand / Prox2. Keypad = 4 or 8 Bit Output (see mode)3. LED Mode = 2-WIRE LED CONTROL54 revision 1
Alternative Reader Wiring Guide11.1.5 LED Operation
Mode Series II Secure Keypad Series III Secure Keypad
Card and PIN N/A Blinking red at bottom of keypad
Card only N/A Blinking red at bottom of keypad
Card or PIN Blinking red and [*] key on keypad solid
Blinking red at bottom of keypad
Cipher lock emulation Blinking red and [*] key on keypad solid
Blinking red at bottom of keypad
Facility code mode N/A
* This mode is unsupported. Any entry within the Code Length will let someone gain access because the facility code is set in the reader.
Blinking red at bottom of keypad
Locked Solid red at bottom of keypad Solid red at bottom of keypad
Unlocked Solid yellow at bottom of keypad Solid yellow at bottom of keypad
Power up condition Blinking red at bottom of keypad. Keypad will display firmware version and operating mode.
Keypad will display firmware version and operating mode
Access granted Blinking yellow at bottom of keypad Blinking yellow at bottom of keypad
Access denied Solid red at bottom of keypad Solid red
Waiting for PIN Blinking red and [*] key on keypad solid
Blinking red and yellow, * key on keypad solid
Waiting for second card Blinking yellow at bottom of keypad
* This mode is unsupported because there are times when a second entry creates an invalid card format.
Alternating red and yellow at bottom of keypad
Reader LED software setup
2-wire LED control 2-wire LED control
Reader type Wiegand/Prox Wiegand/Prox
Keypad 4-bit output keypad 8-bit output keypad
+ 12 V Pin 3 Pin 3
DAT 0 Pin 7 Pin 7
DAT 1 Pin 5 pin 5
LED Pin 4 Pin 4
BZR Pin 8 Pin 8
GND Pin 2 Pin 2revision 1 55
Codeguard Series II/III The star [*] key must be pressed prior to PIN entry.
The star [*] key always illuminated red.
Upper left LED blinks with each key press.
Pressing the [*] key will activate keypad, rescramble keys, and transmit the * key code to the OnGuard system.
Keypad commands sometimes are not accepted, likely because of the multiple functions of the star [*] key. Pressing the star [*] key twice before commands may help.
Earth ground Case ground Not connected, or connect to Pin 2 (avoid ground loops)
Mode Series II Secure Keypad Series III Secure Keypad56 revision 1
Alternative Reader Wiring Guide12. Cross Match Readers
12.1. Cross Match 900xxx TWIC Readers
Cross Match TWIC readers (models 90223, 900236, 900260) are supported. The average reader draw is 325mA @ 12 VDC. General power requirements: +9 to +18 VDC, 6W total.
12.1.1 Wiring the LNL-1300
Single Reader Interface Module
Tie to Earth Ground
DATA/D0
VO
LED
BZR
CLK/D1
GND
DRAIN
Brown
White
Green
Reader LED
Black
TYPICAL SOFTWARE SETTINGS1. Reader Type = Mag w/Wiegand Output2. Keypad = Eight Bit Output Keypads 3. LED Mode = 1-WIRE LED CONTROLrevision 1 57
Cross Match Readers12.1.2 Wiring the LNL-1320
12.1.3 Custom LED Configuration
There are two options for LED functionality. These are configured by a toggle in the devices configuration web interface menu.
Local LED Control This option allows the readers internal logic to control all LED behavior.
Let Wiegand Panel Drive Grant LEDs This option lets the Lenel Hardware manage some LED behavior, such as indicating door unlocked.
Dual Reader Interface Module
Tie to Earth
Ground
DATA/D0
VO
LEDBZR
CLK/D1
GND
DRAIN
Brown
White
Green
Black
Reader LED
TYPICAL SOFTWARE SETTINGS1. Reader Type = Mag w/Wiegand Output2. Keypad = Eight Bit Output Keypads 3. LED Mode = 1-WIRE LED CONTROL58 revision 1
Alternative Reader Wiring Guiderevision 1 59
Cross Match Readers60 revision 1
Alternative Reader Wiring Guide13. Deister Electronics
13.1. Smart Card Reader Model PRM 5M, PRX 5 HSF
The smart card reader can operate between 8 and 30 VDC. In order for the reader LEDs to function properly, the reader will need to be set up for 2-wire control.
13.1.1 Wiring the LNL-1300
deis ere ectronics
+ Supply
D1 (C
lock)
D0 (D
ata)
GN
D
Green LE
D
Red LE
D
1 2 3 4 5 6 7 8 9 10 11 12TERMINAL STRIP ON BACK OF READER
VO
LED
BZR
CLK/D1
DATA/D0
GND
Single Reader Interface Module
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 2-WIRE LED CONTROLrevision 1 61
Deister Electronics13.1.2 Wiring the LNL-1320
13.2. Reader Model PRL5/2 KPL5/2
This reader can operate between 8 and 30 VDC.
deis ere ectronics
+ Supply
D1 (C
lock)
D0 (D
ata)
GN
D
Green LE
D
Red LE
D
1 2 3 4 5 6 7 8 9 10 11 12TERMINAL STRIP ON BACK OF READER
Reader 1
VO
LED
BZR
CLK/D1
DATA/D0
GND
Dual Reader Interface Module
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 2-WIRE LED CONTROL62 revision 1
Alternative Reader Wiring Guide13.2.1 Wiring the LNL-1300
+ Supply
D1 (C
lock)
D0 (D
ata)
GN
D
Green LED
Red LE
D
1 2 3 4 5 6 7 8 9 10 11 12TERMINAL BLOCK ON BACK OF READER
VO
LED
BZR
CLK/D1
DATA/D0
GND
Single Reader Interface Module
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 2-WIRE LED CONTROLrevision 1 63
Deister Electronics13.2.2 Wiring the LNL-1320
+ Supply
D1 (C
lock)
D0 (D
ata)
GN
D
Green LE
D
Red LED
1 2 3 4 5 6 7 8 9 10 11 12TERMINAL BLOCK ON BACK OF READER
Reader 1
VO
LED
BZR
CLK/D1
DATA/D0
GND
Dual Reader Interface Module
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 2-WIRE LED CONTROL64 revision 1
Alternative Reader Wiring Guide14. Dorado Readers
Use the following diagrams to wire Single/Dual Reader Interface Modules and Dorado readers.
14.1. Dorado Reader Model 644
For the Dorado Reader 644, a 16-position rotary switch (Trim POT) is now used for reader configuration. It is located inside the housing on the circuit board. The LED control is standard single wire. The reader should be configured to setting 8 (EMPI cards, 26-bit Wiegand).
14.1.1 Wiring the LNL-1300
Brown
White
Yellow
Red
Black
Dorado Reader Model 644
Green
GND
VDC 5 VDC Power Supply
TYPICAL SOFTWARE SETTINGSReader Type = Mag w/Wiegand Output
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SG
Single Reader Interface Modulerevision 1 65
Dorado Readers14.1.2 Wiring the LNL-1320
Brown wire
Green wire
Yellow wire
Red wire
Black wire
Dorado Reader Model 644
White wire
REA
DER
1VO
LED
BZR
D1/CLK
D0/DATA
GND
Dual Reader Interface Module
DUAL READER INTERFACE MODULE CONFIGURATION1. The 1320 must be set to 5 VDC output (jumper J4)2. Use Regulated Mode for the 1320 (jumper J2)
5 VDC
TYPICAL SOFTWARE SETTINGSReader Type = Mag w/Wiegand Output66 revision 1
Alternative Reader Wiring Guide14.2. Dorado Reader Model 780
14.2.1 Wiring the LNL-1300
Switch Set for Mode 5ABA Card Clock &
Data Black wire
Brown wire
Green wire
White wire
Red wire
Dorado ReaderModel 780
Yellow wire
Single Reader Interface Module with aDorado 780 Card and Pin Reader
A
B
C
D
SW1
ON
OFF
Software Settings: Reader interface All other readers Dorado LED control 8 Bit Pin numbers Requires Firmware Revision for the Dual Reader Interface
10278 0 MR-52R1.04aMSC-C97-8 STO
or for Single Reader Interface10241 2 MR-50R1.06MSC (c) 95-8
GND
12 VDCPower Supply
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SG
80 mA maximumrevision 1 67
Dorado Readers14.2.2 Wiring the LNL-1320
Switch Set for Mode 5ABA Card Clock & DataYellow wire
White wire
Brown wire
Red wire
Black wire
Dorado Reader Model780
Green wire
RE
AD
ER
1R
EA
DE
R 2
VO
LED
BZR
D1/CLK
D0/DATA
GND
Dual Reader Interface Module with aDorado 780 Card and Pin Reader
VO
LED
BZR
D1/CLK
D0/DATA
GND
See manual for 12 VDC1320 Jumper settingsJ4 - OFF, J2 - UNREG
A
B
C
D
SW1
ON
OFFSoftware Settings: Reader interface All other readers Dorado LED control 8 Bit Pin numbers Requires Firmware Revision for the Dual Reader Interface
10278 0 MR-52R1.04aMSC-C97-8 STO
or for Single Reader Interface10241 2 MR-50R1.06MSC (c) 95-8 68 revision 1
Alternative Reader Wiring Guide14.3. Dorado Reader Model 611
14.4. Dorado Elevator Reader 570
This reader operates at 35 mA at +5.5 volts (regulated 4.75 to 5.75).
If you are going to power the reader from the LNL-1320, set jumper 4 to the ON position for 5 volts and jumper 2 for regulated mode.
A four-position DIP switch is located on the reader circuit board to control the reader options. The reader should be set to Mode 6. Note that the fourth switch is not used and should be set to the OFF position.
Mode A B C D Function
6 ON off ON off ABA card, all bits Wiegand
Brown wire
Green wire
Yellow wire
Red wire
Black wire
A
B
C
D
ON
DoradoReader
Model 611
White wire
VO
LED
BZR
D1/CLK
D0/DATA
GND
Dual Reader Interface Module
VO
LED
BZR
D1/CLK
D0/DATA
GND
GND
VDC 5 VDCPower Supply (35 mA)
Software Settings: Reader interface All other
readers One Wire LED Control
The Dual Reader Interface must have Jumper J4 ON for 5 VDC Operation orExternal Power supply must be used as shown below
REA
DER
1R
EAD
ER 2
See manual for voltage andcurrent recommendations.
OFFrevision 1 69
Dorado Readers14.4.1 Wiring the LNL-1300
The wires are connected as follows:
Reader wire color Association on LNL-1300
Yellow BZR
Brown LED
White CLK/D1
Green DATA/D0
Single ReaderInterface Module
Tie to EarthGround
DATA/D0
VO
LED
BZR
CLK/D1
GND
Yellow
BrownWhiteGreen
Red to +5VDC
Black to Common
TYPICAL SOFTWARE SETTINGS1. Reader Type = MAG w/Wiegand Output2. Keypad = No Keypad3. LED Mode = 2-WIRE LED CONTROL70 revision 1
Alternative Reader Wiring Guide14.4.2 Wiring the LNL-1320
14.5. Dorado 230/240 Combination Readers
There are two types of these combination readers. Model 230 is a combination magnetic stripe and proximity reader. Model 240 is a combination magnetic strip and proximity reader with a keypad. These readers operate at 5-24 VDC. The typical current draw is 75 mA.
The 16 position rotary switch will control the formats of the reader and should be set to 0. Position 0 is ABA HID all bits ABA, no leading or trailing zeros, Wiegand output. For HID prox, the number of output bits on the card are not defined by selector switch.
Dual ReaderInterface Module
Reader 1
VOLED
BZRCLK/D1
DATA/D0GND
Brown
White
Green
Tie to EarthGround
Yellow
Red
Black
TYPICAL SOFTWARE SETTINGS1. Reader Type = MAG w/Wiegand Output2. Keypad = No Keypad3. LED Mode = 2-WIRE LED CONTROLrevision 1 71
Dorado Readers14.5.1 Wiring the LNL-1300
14.5.2 Wiring the LNL-1320
Brown
White
Green
Red
Black
Single Reader Interface Module
DATA/D0
VO
LED
BZR
CLK/D1
GND
TYPICAL SOFTWARE SETTINGS1. Reader Type = MAG W/WIEGAND OUTPUT2. Keypad = EIGHT BIT OUTPUT KEYPADS3. LED Mode = 1-WIRE LED CONTROL
Dual Reader Interface Module
Reader 1
VO
LEDBZR
CLK/D1
DATA/D0GND
Brown
White
Green
Red
Black
TYPICAL SOFTWARE SETTINGS1. Reader Type = MAG W/ WIEGAND OUTPUT2. Keypad = EIGHT BIT OUTPUT KEYPADS3. LED Mode = 1-WIRE LED CONTROL72 revision 1
Alternative Reader Wiring Guiderevision 1 73
Dorado Readers74 revision 1
Alternative Reader Wiring Guide15. Essex Keypads
Use the following diagrams to wire Single/Dual Reader Interface Modules and Essex keypad readers.
15.1. Essex Keypad Reader #KTP-16212SLI
15.1.1 Wiring the LNL-1300 (Single Wire LED Control)
GND
12 VDCPower Supply
1 2
3 4
5 6
7 8
9 0
#
Brown - LED wire
Black - Ground
Orange
Red - Vcc
Green - Data 0
White - Data 1
Yellow - LED wire
Tan - Case
Blue
Essex KeypadPart # KTP-16212SLI
SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. Keypad Type = Eight bit output keypad
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SG
Single Reader Interface Modulerevision 1 75
Essex Keypads15.1.2 Wiring the LNL-1320 (Single Wire LED Control)
REA
DER
1R
EAD
ER 2
VO
LED
BZR
D1/CLK
D0/DATA
GND
Dual ReaderInterface Module
VO
LED
BZR
D1/CLK
D0/DATA
GND
Brown - LED wire
Black - Ground
Orange
Red - Vcc
Green - Data 0
White - Data 1
Yellow - LED wire
Tan - Case Ground
Blue
1 2
3 4
5 6
7 8
9 0
#
Essex KeypadPart # KTP-16212SLI
TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. Keypad Type = Eight bit output3. Jumper J4 must be set to 12 VDC4. 2-wire LED control76 revision 1
Alternative Reader Wiring Guide15.2. Essex Keypad Reader #KTP-163SN
15.2.1 Wiring the LNL-1300 (Single Wire LED Control)
GND
12 VDC Power Supply
Brown - LED wire
Black - Ground
Orange
Red - Vcc
Green - Data 0
White - Data 1
Yellow - LED wire
Tan - Case
Blue - CCTV
31 2
64 5
97 8
# 0
Essex KeypadPart # KTP-163SN
SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. Keypad Type = Eight bit output
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SG
Single Reader Interface Modulerevision 1 77
Essex Keypads15.2.2 Wiring the LNL-1320 (Single Wire LED Control)
RE
AD
ER
1R
EA
DE
R 2
VO
LED
BZR
D1/CLK
D0/DATA
GND
Dual ReaderInterface Module
VO
LED
BZR
D1/CLK
D0/DATA
GND
31 2
64 5
97 8
# 0
Brown - LED wire
Black - Ground
Orange
Red - Vcc
Green - Data 0
White - Data 1
Yellow - LED wire
Tan - Case Ground
Blue - CCTV
Essex KeypadPart # KTP-163SNSOFTWARE SETTINGS
1. Reader Type = Wiegand/Prox2. Keypad Type = Eight bit output3. Jumper J4 must be set to 12 VDC4. Jumper J2 must be set to Unregulated
Mode.5. 2-wire LED control78 revision 1
Alternative Reader Wiring Guide16. HID Readers
Use the following diagrams to wire Single/Dual Reader Interface Modules and HID readers.
16.1. HID ProxPro
16.1.1 Wiring the LNL-1300
1 - DC+
2 - GND
3 - Data 0
4 - Data 15 - Data RTN
6 - Green LED7 - Red LED8 - Beeper9 - Hold
10 - COM
11 - Tamper
TB1
Tamper SW123
P3
P1
1 2 3
SW1
HID ProxPro
12 VDC +Power Supply(125 mA)-
TYPICAL SOFTWARE SETTINGS1. Reader Type - Wiegand/Prox2. HID-09 kepad - eight-bit output keypad
HID-00 keypad - four-bit output keypad
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SG
Single ReaderInterface Modulerevision 1 79
HID Readers16.1.2 Wiring the LNL-1320
1 - DC+
2 - GND
3 - Data 0
4 - Data 15 - Data RTN
6 - Green LED
7 - Red LED8 - Beeper9 - Hold
10 - COM
11 - Tamper
TB1
Tamper SW123
P3
P11 2 3
SW1
HID ProxPro
RE
AD
ER
1R
EA
DE
R 2
VO
LED
BZR
D1/CLK
D0/DATA
GND
VO
LED
BZR
D1/CLK
D0/DATA
GND
Dual ReaderInterface Module
TYPICAL SOFTWARE SETTINGS1. Reader Type - Wiegand/Prox2. HID-09 kepad - eight-bit output keypad
HID-00 keypad - four-bit output keypad* Use the 1320 in Unregulated Mode (jumper J2)80 revision 1
Alternative Reader Wiring Guide16.2. HID MaxiProx 5370 A-1
16.2.1 Wiring the LNL-1300
B
A
J3
U1
J4
REA
DER
IN
TERF
AC
EN C C N O N O N C C + 12
V
GN
D
I2-
I2+
I1+
I1+
K1 K2
1
2 3
4
5 6
7
8
J2GN
D
BZR LE
D
CLK
/D1
DAT
/D0
+12V
TR+
TR-
SG
Neutral (white)Hot (black)
Ground (green)
11 - Tamper Select10 - Tamper Common9 - Hold (blue)8 - Beeper (yellow)7 - Red LED (brown)6 - GRN (orange)5 - Data RTN (black)4 - Data-1 (white)3 - Data-0 (green)2 - Ground (black)1 - +DC (red)
on
8 7 6 5 4 3 2 1
Fuse
AC
AC
- BA
T +
+ DC -
1234
ON
SMP5PM
24VDC
Fuse
AC
A
C- B
AT
+
+ DC -
1234
ON
SMP3PM
12VDC
HIDMaxiProx5370 A-1
TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. No keypadrevision 1 81
HID Readers16.3. HID MaxiProx 5370/5375AGN00
16.3.1 Wiring the LNL-1320
D1 D2
INP
UTS
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
IN 7
IN 8
IN 9GNDIN 10
U10
J4
IN - 5VOUT - 12V
RDR POWERREG UNREG
J2
GND
DAT
CLK
BZ
A L
EO
VO
D0
D1GN
D D
AT C
LK
BZA
LEO
V
OD0
D1 RE
ADER
2RE
ADER
1
SN
REV
PN
RS
-485
TR +
TR -
R +
R -
SG
12V
ACDC
AC
GND
J6
J5
J5, J6TERMINATOR
2W 4WJ3
RS-485
U1
U2OFF ON
S1
8 7
6 5
4
3 2 1
NO
C
N
C
NO
C
NC
RLY
2
RLY
1NO
C
NC
NO
C
N
CRL
Y 4
R
LY 3
NO
C
N
C
NO
C
NC
RLY
6
RLY
5
C2
C1
COM k5NC
NO
C2
C1
COM k3NC
NO
C2
C1
COM k1NC
NO
C2
C1
COM k2NC
NO
C2
C1
COM k4NC
NO
C2
C1
COM k6NC
NO
TB1
TB2
TB3
TB4
TB5
TB6
TB7
R120
TB12
TB11
TB10
TB9C3
TB8
Neutral (white)Hot (black)
Ground (green)
11 - Tamper Select10 - Tamper Common9 - Hold (blue)8 - Beeper (yellow)7 - Red LED (brown)6 - GRN (orange)5 - Data RTN (black)4 - Data-1 (white)3 - Data-0 (green)2 - Ground (black)1 - +DC (red)
on
8 7 6 5 4 3 2 1
Fuse
AC A
C- B
AT
+
+ DC -
1234
ON
SMP5PM
24VDC
Fuse
AC
A
C- B
AT
+
+ DC -
1234
ON
SMP3PM
12VDC
HIDMaxiProx5370 A-1
TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. No keypad82 revision 1
Alternative Reader Wiring Guide16.4. Hughes MiniProx
16.4.1 Wiring the LNL-1300
1 - DC+
2 - GND
3 - DATA "0"
4 - DATA "1"
5 - DATA RTN
6 - Green LED
7 - Red LED
8 - Beeper
9 - Hold
Red
Black
Green
White
Black
Orange
Brown
Yellow
Blue
N/C
N/C
Hughes MiniProx ReaderTYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. No keypad
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SG
Single ReaderInterface Module
N/Crevision 1 83
HID Readers16.4.2 Wiring the LNL-1320
VO
LED
BZR
D1/CLK
D0/DATA
GND
VO
LED
BZR
D1/CLK
D0/DATA
GND
RE
AD
ER
1R
EA
DE
R 2
Dual ReaderInterface Module
1 - DC+
2 - GND
3 - DATA "0"
4 - DATA "1"
5 - DATA RTN
6 - Green LED
7 - Red LED
8 - Beeper
9 - Hold
Red
Black
Green
White
Black
Orange
Brown
Yellow
BlueN/C
Hughes MiniProx Reader
TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand/Prox2. No keypad* Use Unregulated Mode for the 1320, jumper J2
N/C
N/C84 revision 1
Alternative Reader Wiring Guide16.5. Classic, EPIC Swipe and Pinpad Wiegand Readers
16.5.1 Wiring the LNL-1300
16.5.2 Wiring the LNL-1320
+ 12 VDC
- GND
TYPICAL SOFTWARE SETTINGS1. 2-Wire LED Support2. No keypad3. Wiegand/Prox data type
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SG
Single ReaderInterface Module
HID Classic Swipe Reader, EPIC SwipeReader, or Pinpad Wiegand Reader
Black - Ground
Brown - Red LED
Violet - Green LED
White - Data 1
Green - Data 0
Red - 5-12 VDC
Blue - not used
Yellow - not used
Orange - notused
TYPICAL SOFTWARE SETTINGS1. 2-Wire LED Support2. No keypad3. Wiegand/Prox data type* Use unregulated mode for the 1320, Jumper J2
HID Classic Swipe Reader, EPIC SwipeReader, or Pinpad Wiegand Reader
Red - 5-12 VDC
Violet - Green LED
Brown - Red LED
White - Data 1
Green - Data 0
Black - Ground
Blue - not used
Yellow - not used
Orange - notused
RE
AD
ER
1R
EA
DE
R 2
VO
LED
BZR
D1/CLK
D0/DATA
GND
VO
LED
BZR
D1/CLK
D0/DATA
GND
Dual ReaderInterface Modulerevision 1 85
HID Readers16.6. ProxPoint Readers
16.6.1 Wiring the LNL-1300
16.6.2 Wiring the LNL-1320
TYPICAL SOFTWARE SETTINGS1. 2-Wire LED Support2. No keypad3. Wiegand/Prox data type
H I D
ProxPoint Reader
White - Data 1
Green - Data 0
Black - Ground
Orange - LED
Single ReaderInterface Module
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SG
Red - 5-12 VDC
Yellow - BZR
TYPICAL SOFTWARE SETTINGS1. 2-Wire LED Support2. No keypad3. Wiegand/Prox data type
Red - 5-12 VDC
White - Data 1
Green - Data 0
Black - Ground
Yellow - BZR
REA
DER
1R
EAD
ER 2
VO
LED
BZR
D1/CLK
D0/DATA
GND
VO
LED
BZR
D1/CLK
D0/DATA
GND
Dual ReaderInterface Module
H I D
ProxPoint Reader
Orange - LED86 revision 1
Alternative Reader Wiring Guide16.7. ProxPro II
The ProxPro II reader (model number 5455BBn00) operates at 5-16 VDC. The average current draw at 12 VDC is 30 mA. The LEDs and buzzer function in the same way as standard HID Wiegand/proximity readers.
16.7.1 Wiring the LNL-1300
Orange
Yellow
White
Green
Red
Black
Single Reader Interface Module
HID
DATA/D0
VO
LED
BZR
CLK/D1
GND
Drain wire & Shield
to Ground
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROLrevision 1 87
HID Readers16.7.2 Wiring the LNL-1320
Dual Reader Interface Module
HID
Reader 1
VO
LEDBZR
CLK/D1
DATA/D0GND
Orange
YellowWhite
Green
Red
BlackShield
to Drain
Ground
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1-WIRE LED CONTROL88 revision 1
Alternative Reader Wiring Guide16.8. iClass Reader/Encoder
This reader (RW300/RW400/RW400Prgm) operates at 10-16 VDC. The average current draw is 80-260 mA. When communication to the unit is successful, the LED remains solid green.
Note: Due to timing issues with the encoder, this unit cannot be connected to a multiport serial adapter.
Wiring Function DB9 pin-out (female)
Yellow Speaker Not used
Blue Hold Not used
Violet Open collector Not used
White Data 1 Not used
Green Data 0 Not used
Orange Green LED Not used
Brown Red LED Not used
Red +DC (10-16 VDC) +DC (10-16 VDC)
Black Ground DC Ground
Gray RX (serial receive) Pin 3
Red/Green DSR Not used
Pink TX (serial transmit) Pin 2
Red/Yellow DTR Not used
Drain Shield ground Pin 5
HID
PIN 2PIN 3
PIN 5
To DB9 SerialCommunication
Port on PCrevision 1 89
HID ReadersWhen configuring the access control software, this encoder will most likely be a standalone device connected to the workstation. Be sure to select a unique name for the encoder. Select HID iCLASS for the device type and iClass for the card technology.
Typical Communication Settings
Comm. port: configurable
Baud rate: 57600
Data bits: 8 bit
Parity: Even
Stop bits: 290 revision 1
Alternative Reader Wiring Guide16.9. iClass Reader
The HID iClass Reader (model numbers R10/R30/R40) operates at 10-16 VDC. The average current draw for the R10 is 65-122 mA; the R30: 80-260 mA; the R40: 80-260 mA. The LEDs and buzzer function the same as standard HID Wiegand/Prox readers.
16.9.1 Wiring the LNL-1300
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROL
Orange
Brown
White
Green
Red
Black
Single Reader InterfaceModule
DATA/D0
VO
LED
BZR
CLK/D1
GND
HID
Tie to EarthGroundrevision 1 91
HID Readers16.9.2 Wiring the LNL-1320
16.10. iClass RK-40
The HID iClass RK-40 reader has an 8 bit keypad. It operates at 10-16 VDC. The average current draw is 72/244 mA at 12 V. The LEDs and buzzer function the same as standard HID Wiegand/Prox readers.
Dual Reader InterfaceModule
Reader 1
VO
LEDBZR
CLK/D1
DATA/D0GND
OrangeBrownWhite
Green
Red
Black
HID
Tie to EarthGround
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROL92 revision 1
Alternative Reader Wiring Guide16.10.1 Wiring the LNL-1300
Pin 5 (Green LED)
Pin 6 (Red LED)
Pin 4 (Data 1)
Pin 3 (Data 0)
Pin 1 (+DC (10-16V)
Pin 2 (Ground)
Single Reader Interface Module
DATA/D0
VO
LED
BZR
CLK/D1
GND
Tie to Earth
Ground
HID
1 2 3
4 5 6
7
*98
0 #
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = EIGHT BIT OUTPUT KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROLrevision 1 93
HID Readers16.10.2 Wiring the LNL-1320
16.11. EntryProx 4045-905
The EntryProx is a standalone reader. It is ideal for providing single-door proximity access control.
In this configuration, the keypad does not send separate key data. When the keypad is used, it outputs the cardholder/badge ID number.
The system transmits keypad PINs while operating in Wiegand mode by processing any digit sequence terminated with the [*] key as 26-bit Wiegand data. The current facility code (set using Code 32 - 2) will be used. Entering any PIN over 65535 will cause an error condition and no data will be sent.
Because keypad data is sent in a card data format, it may not be possible to perform card and PIN operation. If 26-bit format as PIN data cannot be interpreted, be sure to enter it into the badge ID field, and not the keypad PIN number field.
Pin 5 (Green LED)
Pin 6 (Red LED)
Pin 4 (Data 1)
Pin 3 (Data 0)
Pin 1 (+DC (10-16V)
Pin 2 (Ground)
Single ReaderInterface Module
DATA/D0
VO
LED
BZR
CLK/D1
GND
Tie toEarth
Ground
HID
1 2 3
4 5 6
7
*98
0 #
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = EIGHT BIT OUTPUT KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROL94 revision 1
Alternative Reader Wiring Guide16.11.1 Wiring the LNL-1300
Single Reader Interface Module
Blue - not used
Green - Wiegand Data 0
White - Wiegand Data 1
Brown - Wiegand LED
DATA/D0
VO
LED
BZR
CLK/D1
GNDrevision 1 95
HID Readers16.11.2 Wiring the LNL-1320
16.12. SensorKey Reader
This reader operates at 40 mA at 5-12 VDC.
Dual Reader Interface Module
Reader 1
VO
LEDBZR
CLK/D1
DATA/D0GND
Blu
e - n
ot u
sed
Red +12 VDC
Brown - Wiegand LED
White - Wiegand Data 1
Green - Wiegand Data 0
Black - Ground96 revision 1
Alternative Reader Wiring Guide16.12.1 Wiring the LNL-1300
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND / PROX2. Keypad = No Keypad 3. LED Mode = 1 or 2-WIRE LED CONTROL
Single Reader Interface Module
Tie to Earth Ground
DATA/D0
VO
LED
BZR
CLK/D1
GND
(Brown)(White)(Green)
(Black)
(Red)
(Blue)revision 1 97
HID Readers16.12.2 Wiring the LNL-1320
16.13. HID MIFARE 6055
This reader operates at 9-14 VDC (16 VDC maximum). The average current draw is 100mA at 12 VDC. A linear power supply recommended.
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND / PROX2. Keypad = No Keypad 3. LED Mode = 1 or 2-WIRE LED CONTROL
Dual Reader Interface Module
Tie to Earth Ground
DATA/D0
VO
LED
BZR
CLK/D1
GND
(Brown)
(White)(Green)
(Black)
(Red)
(Blue)98 revision 1
Alternative Reader Wiring Guide16.13.1 Wiring the LNL-1300
16.13.2 Wiring the LNL-1320
Single Reader Interface Module
GND
BZRLED
CLK/D1
DATA/D0VO
YellowBrownWhite
Green
Black
Red
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 2-WIRE LED CONTROL
Other wires not used
MIFAREHID
Dual Reader Interface Module
Reader 1
VO
LEDBZR
CLK/D1
DATA/D0GND
BrownYellowWhite
Green
Red
Black
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 2-WIRE LED CONTROL
MIFAREHID
Other wires not usedrevision 1 99
HID Readers16.14. HID LCD and bioCLASS Readers (RWKL550/RWKLB575)
HID LCD and bioCLASS models RWKL550 and RWKLB575 are supported as either Wiegand or OSDP readers.
16.14.1 Wiring the LNL-1300 (Wiegand)
Single Reader Interface Module
DATA/D0
VO
LED
BZR
CLK/D1
GND
NC+DC-DC
NCGREEN
REDNC
NC
DATA 1
DATA 0
Back of Reader
NCDATA 1DATA 0NCNC
To 12VDC
NC
RED
GREEN
Tie to DC-
TYPICAL SOFTWARE SETTINGS1. Reader Type = Wiegand / Prox2. Keypad = Eight Bit Output Keypads3. LED Mode = 1 or 2-WIRE LED CONTROL100 revision 1
Alternative Reader Wiring Guide16.14.2 Wiring the LNL-1320 (Wiegand)
Dual Reader Interface Module
NC+DC-DC
NCGREEN
REDNC
NC
DATA/D0
VO
LEDBZR
CLK/D1
GND
DATA 1
DATA 0
Back of Reader
NCDATA 1DATA 0NCNC
To 12VDC
NC
RED
GREEN
Tie to DC-
1. Reader Type = Wiegand / Prox2. Keypad = Eight Bit Output Keypads3. LED Mode = 1 or 2-WIRE LED CONTROL
TYPICAL SOFTWARE SETTINGSrevision 1 101
HID Readers16.14.3 Wiring the LNL-1300 (OSDP)
Single Reader Interface Module
Series 2
DATA/D0
VO
LED
BZR
CLK/D1
GND
NC+DC-DC
NCNC
NCNC
GPIO1
GPIO1
GPIO2
Back of Reader
NCNCNCNCNC
To 12VDC
GPIO2
Tie to DC-
TYPICAL SOFTWARE SETTINGS
1. Reader Type = OSDP Protocol2. Keypad = Eight Bit Output Keypads3. LED Mode = OSDP LCD Reader102 revision 1
Alternative Reader Wiring Guide16.14.4 Wiring the LNL-1320 (OSDP)
16.15. HID MIFARE Format Secure 6075 Reader
The reader operates at 9 -16 VDC. The average current draw is 15mA/75mA.
Dual Reader Interface Module
Series 2NC
+DC-DC
NCNC
NCNC
GPIO1
DATA/D0
VO
LEDBZR
CLK/D1
GND
GPIO1
GPIO2
Back of Reader
NCNCNCNCNC
To 12VDC
GPIO2
Tie to DC-
TYPICAL SOFTWARE SETTINGS1. Reader Type = OSDP Protocol2. Keypad = Eight Bit Output Keypads3. LED Mode = OSDP LCD Readerrevision 1 103
HID Readers16.15.1 Wiring the LNL-1300
Brown
White
Green
Red
Black
DATA/D0
VO
LED
BZR
CLK/D1
GND
Tie to Earth Ground
Single Reader Interface Module
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROL104 revision 1
Alternative Reader Wiring Guide16.15.2 Wiring the LNL-1320
16.16. HID OSDP Readers
Models 6100BKP through 6181BKP are supported. To use OSDP readers with OnGuard, version 5.12.110 or higher is required. Only Series 2 reader ports offer OSDP support.
Reader 1
VO
LEDBZR
CLK/D1
DATA/D0GND
Brown
White
Green
Red
Black
Tie to Earth Ground
Dual Reader Interface Module
TYPICAL SOFTWARE SETTINGS1. Reader Type = WIEGAND/PROX2. Keypad = NO KEYPAD3. LED Mode = 1 or 2-WIRE LED CONTROLrevision 1 105
HID Readers16.16.1 Wiring the LNL-1300
Series 2 Single Reader Interface Module
DATA/D0
VO
LED
BZR
CLK/D1
GND
NC+DC-DC
NCNC
NCNC
GPIO1
GPIO1
GPIO2
Back of Reader
NCNCNCNCNC
To 12VDC
GPIO2
Tie to DC-
Not UsedNot Used
Not used for 6171/6181
TYPICAL SOFTWARE SETTINGS1. Reader Type = OSDP Protocol2. LED Mode = OSDP Reader for all except 6171 and 6181, OSDP LCD Reader for 6171, and 6181106 revision 1
Alternative Reader Wiring Guide16.16.2 Wiring the LNL-1320
16.17. SmartID/SmartTRANS Models S10/SK10, SP10/SPK10
The following diagrams show wiring for Data 1/Data 0. If you are using Clock/Data, the wiring for the two leads connected at 3 and 4 on the reader should be reversed.
Intelligent Dual Reader Controller/Series 2 Dual Reader Interface Module
NC+DC-DC
NCNC
NCNC
GPIO1
DATA/D0
VO
LEDBZR
CLK/D1
GND
GPIO1
GPIO2
Back of Reader
NCNCNCNCNC
To 12VDC
GPIO2
Tie to DC-
Not used for 6171/6181
Not UsedNot Used
TYPICAL SOFTWARE SETTINGS1. Reader Type = OSDP Protocol2. LED Mode = OSDP Reader for all except 6171 and 6181, OSDP LCD Reader for 6171 and 6181revision 1 107
HID Readers16.17.1 Wiring the LNL-1300
Single Reader Interface Module
VO
LED
BZR
CLK/D1
DATA/D0
GND
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. LED Mode = 2-WIRE LED CONTROL
Connector from reader
(1)
(7)
(6)
(5)
(4)(3)
(2)
Green LED
Red LED
Clock/D0
Data/D1
Do not connect
Do not connect
(8)
GroundPower
(5-12 VDC)108 revision 1
Alternative Reader Wiring Guide16.17.2 Wiring the LNL-1320
Reader 1
VO
LED
BZR
CLK/D1
DATA/D0
GND
Dual Reader Interface Module
Connector from reader
(1)
(7)
(6)
(5)
(4)(3)
(2)
Green LED
Red LED
Clock/D0
Data/D1
Do not connect
Do not connect
TYPICAL SOFTWARE SETTINGS
1. Reader Type = WIEGAND/PROX2. LED Mode = 2-WIRE LED CONTROL
(8)
GroundPower (5-12 VDC)revision 1 109
HID Readers110 revision 1
Alternative Reader Wiring Guide17. IDH Max
IDH Max readers include all door components a reader device, lock set, door contact, and request to exit sensors.
17.1. IDH Max Door Readers
Use the following diagrams to wire Single/Dual Reader Interface Modules and IDH Max readers.revision 1 111
IDH Max17.1.1 Wiring the LNL-1300
B AJ3
U1
J4
SINGLE READER INTERFACE MODULE
NCCNONONCC
+12VGNDI2-I2+I1+
I1+ 1 2 3 4 5 6 7 8
J2
GNDBZRLED
CLK/D1DAT/D0
+12VTR+TR-SG
CP
NCN
CG
ND
BPR
GR
NRE
DD
1D0
STK
RQ E
DS
LS
1
Black
BrownWhiteGreen
To 12VDC
Ora
nge
Gre
en
Red
Bla
ck
Off
On
TYPICAL SOFTWARE SETTINGS 1. Reader Type = Dependant on Model WIEGAND/PROX HID Reader/iClass ALL OTHER READERS Mag Reader 2. Keypad = NO KEYPAD 3. LED Mode = 1-Wire LED Control
IDH MAX PANEL INTERFACE
12V GND COM+ COM- 12V GND112 revision 1
Alternative Reader Wiring Guide17.1.2 Wiring the LNL-1320
DUAL READER INTERFACE MODULE
NCC
NO
IN 2
IN 1
GND
BZRLED
CLK/D1DAT/D0
+12VC
PN
CN
CG
ND
BPR
GR
NR
ED
D1
D0
STK
RQ E
DSLS
12V GND COM+ COM-12V GND
1
To 12VDC
Ora
nge
Gre
en
Red
Blac
k
Off
On
TYPICAL SOFTWARE SETTINGS 1. Reader Type = Dependant on Model WIEGAND/PROX HID Reader/iClass ALL OTHER READERS Mag Reader 2. Keypad = NO KEYPAD 3. LED Mode = 1-Wire LED Control
IDH MAX PANEL INTERFACE
NCC
NO
Rea
der 1
RLY
1 R
LY 2revision 1 113
IDH Max114 revision 1
Alternative Reader Wiring Guide18. ID Solutions Readers
Use the following diagrams to wire Single/Dual Reader Interface Modules and ID Solutions readers.
18.1. ID Solutions Model 8030/8035 Bar Code Reader
18.1.1 Wiring the LNL-1300
Single Reader Interface Module
Red - DC Input
Black - Supply Ground
White - Data 1/Clock
Green - Data 0/Data
Brown - LED Control Input
ID SolutionsBar Code Reader,Model 8030/8035
GND
12 V Power Supply
TYPICAL SOFTWARE SETTINGS
1. Reader Type = All other readers2. No keypad
GND
BZR
LED
CLK/D1
DAT/D0
+12V
TR+
TR-
SGrevision 1 115
ID Solutions Readers18.1.2 Wiring the LNL-1320
Red - DC Input
Black - Supply Ground
White - Data 1/Clock
Green - Data 0/Data
Brown - LED Control Input
REA
DER
1R
EAD
ER 2
VO
LED
BZR
D1/CLK
D0/DATA
GND
Dual Reader Interface Module
VO
LED
BZR
D1/CLK
D0/DATA
GND
ID SolutionsBar Code Reader,Model 8030/8035
TYPICAL SOFTWARE SETTINGS1. Reader Type = All other readers2. No keypad3. Use the 1320 in Unregulated Mode (jumper J2)116 revision 1
Alternative Reader Wiring Guide19. Infographics Readers
Use the following diagrams to wire Single/Dual Reader Interface Modules and Infographics readers.
19.1. Infographics Reader OTD-60
19.1.1 Wiring the LNL-1300
Bla
ck -
Yel
low
LE
D (n
ot u
sed)
Single Reader Interface Module
1. Grey - 0 Volts
Brown - Reader Clock
Yellow - Reader Data
4. Green - +5 Volts
Red - Green LED
InfographicsRead
Top Related