&(57,),&$7( 2) 352'8&7 &21)250,7< - ArcelorMittalDM-DCLD-RD-DP21-2129 (IC) “Specific Rules for...
Transcript of &(57,),&$7( 2) 352'8&7 &21)250,7< - ArcelorMittalDM-DCLD-RD-DP21-2129 (IC) “Specific Rules for...
-
CERTIFICATE OF PRODUCT CONFORMITYDubai Central Laboratory Department (DCLD) of Dubai Municipality
hereby attests that the product(s)
Steel for the Reinforcement of Concrete - Weldable Reinforcing Steel(Details as per the attached Scope of Certification)
ARCELOR MITTAL KRYVYI RIH
1, Ordzhonikidze St. Kryvyi Rih 50095, Dnipropetrovsk Region, Ukraine
have been assessed in accordance with DCLD Document Ref. No. DM-DCLD-RD-DP21-2001 (IC) "General Rules for DM third party product certification system through factory assessment" and the relevant Specific Rules, and were found in conformity with the standard specification:
BS 4449: 2005+A3:2016Accordingly, DCLD hereby authorizes the above manufacturer
to affix the DCL Product Conformity Mark on the above-mentioned product(s).
manufactured by:
for / ENGR. AMIN AHMED AMINDirector, Dubai Central Laboratory Department
Dubai Municipality
Certificate No:Valid Until:
Current Issue Date:Original Issue Date:
The attached Scope of Certification bearing the same Certificate Number forms an integral part of this Certificate.This Certificate is an electronic document subject to the Terms and Conditions of the Product Certification System and shall not be reproduced except in full.
CL1002012628/05/2020
29/03/202029/03/2010
DM-DCLD-F-IC-2031 Rev 16
-
DUBAI CENTRAL LABORATORY DEPARTMENT
DCL PRODUCT CONFORMITY CERTIFICATION SCHEME
SCOPE OF CERTIFICATION
FOR CERTIFICATE NO. CL10020126
Page 1 of 1 DM-DCLD-F-IC-2032 R9
P.O. Box 67, DCL, Zabeel Road, Karama, Dubai, UAE
Certificate Issued To: ARCELOR MITTAL KRYVYI RIH
1, Ordzhonikidze Street, Kryvyi Rih 50095, Dnipropetrovs’k
Region-Ukraine
Applicable Standard Specification: BS 4449:2005 + A3:2016 - Specification for Steel for the
Reinforcement of Concrete-Weldable reinforcing steel-Bar,
coil and decoiled product
Applicable Specific Rules: DM-DCLD-RD-DP21-2129 (IC) “Specific Rules for
Certification of Reinforcing Steel Bars (as per BS 4449:2005
+ A3:2016) Through Factory Assessment”.
S/N PRODUCT DESCRIPTION BAR MARKING PRODUCT DETAILS
1.
Steel for reinforcement of
concrete - bars
As per attached DCL Approved
Bar Markings in accordance
with RD-DP21-2091 (IC)
Grade B500B & B500C:
Diameter Sizes: 8 – 32 mm
NOTE 1: This document forms part of the Certificate of Product Conformity bearing the same certificate
number.
NOTE 2: The above product shall bear the DCL Conformity Mark.
NOTE 3: This certificate is extended for Two Months based on the guidelines of DM-DCLD-RD-DP21-
2007 (IC) Special Rules - Guideline for Extraordinary Events (COVID19).
Original Issue Date : 29 March 2010
Current Issue Date : 29 March 2020
Valid Until : 28 May 2020
ARIF HUSAIN AL MARZOOQI
Products Conformity Assessment Section Manager
Dubai Central Laboratory Department
-
APPROVED BY:
ARIF HUSAIN AL MARZOOQI
Products Conformity Assessment Section Manager DM-DCLD-F-IC-2045 R4
DUBAI CENTRAL LABORATORY DEPARTMENT
PRODUCTS CONFORMITY ASSESSMENT SECTION
APPROVED STEEL BAR MARKING
Certification Scheme for Reinforcing Steel
CERTIFIED FACTORY ARCELOR MITTAL KRYVYI RIH
FACTORY LOCATION 1, Ordzhonikidze street, Kryvyi Rih 50095,
Dnipropetrovs’k Region-Ukraine
CERTIFICATE NUMBER CL10020126
COUNTRY CODE 9
MILL NUMBER 31
STANDARD SPECIFICATION BS 4449: 2005 + A3:2016
NOTE: Please refer to the Certificate mentioned above and its Scope of Certification for details regarding
the validity and the sizes covered.
CL10020126 (2020).pdfScope of CL10020126 (2020).pdfCL10020126 Steel Bar Marking (2020).pdf