0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not...
Transcript of 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not...
![Page 1: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/1.jpg)
IPAC
Dealer Guide
Wiring and Programming
IPACGuide
Wiring and Cloud Programming
![Page 2: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/2.jpg)
2
Thank you for purchasing a LiftMaster IPAC system. LiftMaster strongly recommends setting up and confi guring any IPACs and door controllers prior to the day of installation.
TABLE OF CONTENTS
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
How do I login? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Wiring Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Add IPAC Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connect Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connect Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Add IPAC Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Create a New Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Add Doors/Gates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Confi gure a Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wire Door #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wire Door #2 (If applicable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Create a Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Confi gure IPAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
Set Group Privileges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Bulk Load Cards/Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Create Credentialed User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21
Create a Resident . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Create a Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Set a Notifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
Create a New Senior Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
(OVERVIEW IMAGE HERE)(O(O(O(O(O(O((OOOOOOOOOOO(OOOO((OO(O(OOO(OOOOO(O(O(O(O((((((((((((((((((((((((((((( VEVEVEVEVEVEVEEEEVEVEVEVEEVEVEVVEEEVEEEEVEVEEVVVVVVVVEVEEVEVEVEVEEVEVEVVVVVVVEEVEEEEEEVEEVEEEVVVVVVVVVVVEVEEVEEEEEEEERVRVRVRVRVRRVRRVRVVVVVVVVRVVVVRVVVVVRVRVVVVRVRRRRRRRVVVVVRVVRVRVVRVRVVVRVRVVVRRRRRRRRRRRRVVRVRVVVVVVRVRVRVRVRVRVVRRRRRVRVVVRVVVVRVVRVVVVRVRVVRRRRRRVVVVVRVRVRRRRRRRRRRVRVRRRRRR IEIEIEIEIEEEEEEEEEEEIIEIEIEEEEEEIEEEIEIIIEIEIEIEEEEEEIEEEEIEEIEEEEEIIEEEEEEEEEIEIIEEEEEIEIEI WWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWW WWWWWWWWW IMMIMIMMMMMMMMIMMMMMMMMIMMIMMMMMMMMMMIIIIMMMMMMIMIMMMMMMMMMMMMMIIMMIMMMMMIMIMMMMIMMMMMMIIIMMMIMMMMIMIMIMIMMMMMIMMIMIMMMMMMMIMMIMIMIMMIMMIMMIIMAGAGAGAGAGAGGGAGGGGGGAGGAGAGGGAGGGAGGAGAGAAAAAGAGGAGGGAGGGAGAGGAGGGGAAAAAAAAAAAAAGGGAGGGGGGGGAGAGAAAAAAGAGAGGAGGGGAGGAGGGAAAAAAAAAAGGGGGGGGGAGAGGAGAGAAAAAAAAAAAAGAGAAAAAAAAAGA EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEE HEHEHEHEHHEHEHEHEEEHEEHEEEHEEEEHHHEHHHHEEEEHEHEHEHEEHEHHHHHEHHHHHEHEHEHEEEEEEHEHEEHHHHHHHHHHHHHHEEEHEHEEEHEEEHEEHEEHHHHHHHHHHHEEEHEEHEHEHEHEHEHEHEHEHHHHHHHHHHHHHHEHHHHHHEHEEHEEHEHEEHEEEHHHHHHEEHEEHHHEEEEEHHHEHHHHEEEHHHHHEHEEHHHEHHHHH RERERERERERERR ))))))
![Page 3: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/3.jpg)
3
Introduction
Order IPAC and/or door controller (SKU: IPACIPDCC)
Setup LiftMaster Hosted Services Account
Call LiftMaster Customer support at (800) 323-2276 and have credit card and primary account holder information
ready.
NOTE: Record the Administrator ID and you will receive an email to set up a permanent password.
IPAC and IPACIPDCC require an active Internet connection at the installation location (including Cat-5 or Cat-6
at the IPAC installation location).
Multiple connection options:
• High speed Internet
• DSL
Map of facility indicating entrance(s) and exit(s).
Use a map to plan out all entrances and exits to be controlled. Plan wire runs and installation points prior to
getting started.
NOTE: Before installing the IPAC and Door Controller, power on and set up the hardware at your offi ce or shop.
Follow this manual to confi gure the hardware and ensure proper functionality prior to installation. This requires
access to an Internet connection.
1
BEFORE YOU BEGIN:
2
3
4
![Page 4: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/4.jpg)
4
Cloud Login
Open a web browser and type LiftMaster.com/IPAC into the address bar.
Enter login information you were provided
in “Before you get started”. NOTE: ID and
Password are case sensitive.
Click “Log In”.
HOW DO I LOGIN?
1
2
3
4
Scroll down and click “Cloud Login”.
LiftMaster.com/IPAC
![Page 5: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/5.jpg)
5
Wiring Overview
Not responsible for conflicts between the information listed in the wiring diagram and the requirements of your local building codes. The information is for suggested use ONLY. Check your local codes BEFORE installation.
Chasis abierto Open Enclosure
COM LINK -> A B
N.C.
COM
SHLD
N.O.
RELA
Y 1
N.C.
COM
SHLD
N.O.
AU
X 1
N.C.
COM
SHLD
N.O.
RELA
Y 2
N.C.
COM
SHLD
N.O.
AU
X 2
INP
UT 1
REX
2
INP
UT 2
SH
LD
CO
M
SEN
SE
SH
LD
CO
M
SEN
SE
SH
LD
CO
M
SEN
SE
GN
D
SH
IELD
LED
-GR
N
BU
Z
HO
LD
LED
-RED
D0
D1
12V
GN
D
SH
LD
LED
-GR
N
BU
Z
HO
LD
LED
-RED
D0
D1
12V
READER 1
CO
MM
LIN
K M
OD
ULE
RELAY BOARD
READER 2
USB - Device
PE
RIP
HE
RA
LB
OA
RD
CO
NFIG
LA
N
US
B -
AD
MIN
REX 1
SENSE
COM
SHLD
1 2 3
4 5 6
7 8 9
0 #
O NO
N1
2
3
4
CO
NFIG
O NO
N1 2 3
4
POWER
PERIPHERAL BOARD
RELAY 1
Gate/Door Operator, Maglock,
or Door Strike.
AUX 1
Alarm, Light, or Camera
Common
ACCESS POINT 1
ACCESS POINT 1
ACCESS POINT 2
ACCESS POINT 2
N.O.
Common
N.O.
Common
N.O.
Sen
se
Com
mon
Sen
se
Com
mon
Sen
se
Com
mon
INPUT 1 -
Door Sensing
Device for
access point 1
READER 1 -
Passport Receiver
Model PPWR
(factory installed)
READER 2 - Wiegand Device input for access point 2
INPUT 2 - Door Sensing Device for access point 2
REX 1 - Postal Lock,
Exit Request Button
(REX), Keyswitch, Passive
Infrared Device (PIR)
for access point 1
REX 2 - Exit Request Button (REX), Keyswitch, Passive Infrared Device (PIR)
for access point 2.
ETHERNET PORT
CONFIG Common
Config Switches
Sense
RELAY 2
Gate/Door Operator,
Maglock, or Door Strike
AUX 2
Alarm, Light, or Camera
Common
N.O.
Optional KeypadRELAY BOARD
RELAY BOARD
PERIPHERAL BOARD
![Page 6: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/6.jpg)
6
USB - Device
PER
IPH
ER
AL
BO
AR
D
CO
NFIG
LA
N
US
B -
AD
MIN
REX 1
SENSE
COM
SHLDO NO
N1 2 3
4
CO
NFIG
O NO
N1 2 3
4
IPPNL
MAC 00:00:00:00:00:00
CP# TEC–3K–YYYYL
IPPNL
MAC 00:00:00:00:00:00
CP# TEC–3K–YYYYL
CO
NFIG
O NO
N1
2
3
4
Unpack IPAC and set it on a clean surface. Open IPAC using the included Key.
Setup
ADD IPAC PANEL
1
2
3 Write down Control Panel number:
TEC – _ _ – _ _ _ _ _.
Close the door.
Move #1 dipswitch to “ON”
position to enter administration
mode.
PERIPHERAL BOARD
![Page 7: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/7.jpg)
7
COM LINK -> A B
N.C.
COM
SHLD
N.O.
RELA
Y 1
N.C.
COM
SHLD
N.O.
AU
X 1
N.C.
COM
SHLD
N.O.
RELA
Y 2
N.C.
COM
SHLD
N.O.
AU
X 2
INP
UT 1
REX
2
INP
UT 2
SH
LD
CO
M
SEN
SE
SH
LD
CO
M
SEN
SE
SH
LD
CO
M
SEN
SE
GN
D
SH
IELD
LED
-GR
N
BU
Z
HO
LD
LED
-RED
D0
D1
12V
GN
D
SH
LD
LED
-GR
N
BU
Z
HO
LD
LED
-RED
D0
D1
12V
READER 1
CO
MM
LIN
K M
OD
ULE
RELAY BOARD
READER 2
Connect the included power transformer to
the IPAC power input connector using at
least 18 gauge wire (AWG).
NOTE: When installing, make all wire
connections prior to applying power to
the unit.
CONNECT POWER
Wiring
RELAY BOARD
• DO NOT use ANY power supply other than those supplied with your access control panel.
• DO NOT power electronic strikes and latches with the same power supply used to power the access control panel; doing so will cause DAMAGE to the access control panel.
• DO NOT connect the power supply to a switched outlet or otherwise controlled AC outlet.
• DO NOT connect the power supply to the 120 Vac outlet until ALL wiring is completed.
• Install the transient noise suppression device (MOV) supplied with the access control panel for AC powered devices and Diode for DC powered devices.
![Page 8: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/8.jpg)
8
USB - Device
PE
RIP
HE
RA
LB
OA
RD
CO
NFIG
LA
N
US
B -
AD
MIN
REX 1
SENSE
COM
SHLDO NO
N1
2
3
4
IPPNL
MAC 00:00:00:00:00:00
CP# TEC–3K–YYYYL
CO
NFIG
O NO
N1
2
3
4
Connect the IPAC to an available port on
an Internet modem, router, DSL Modem,
or network switch using a Cat-5 or Cat-6
Ethernet cable.
CONNECT ETHERNET
PERIPHERAL BOARD
Wiring
![Page 9: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/9.jpg)
9
On the touch screen, press “DHCP”, then
“Advanced Settings”.
Press “Go Cloud”. IPAC will
download latest fi rmware and
restart.
Programming
ADD IPAC PANEL TO A CLOUD ACCOUNT
1
2
Confi rm the proper fi rmware has been downloaded after the IPAC restarts.
• Press “MISC” then “System Info”.
• Firmware Version should be “5.0.21”.
• If fi rmware starts with a “1” (e.g. 1.2.2) press the “Go Cloud” button and confi rm IPAC downloads the latest
fi rmware and restarts.
3
![Page 10: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/10.jpg)
10
Navigate to Setup –> Sites and Doors –> New Site.
Programming
CREATE A NEW SITE
1
Enter all required fi elds.2
3 Click “Save Site”.
Return the #1 Dipswitch to the OFF position to return IPAC to user mode.
From your computer or tablet open a web browser and log into IPAC hosted service account (LiftMaster.com/IPAC).
From the hosted account page, click “Setup” from the top toolbar.
Navigate to Setup –> Sites and Doors –> New Control Panel.
4
5
6 Name the IPAC panel and enter
Control Panel Number (CP#).
Optional comments may be added
to describe control panel in further
detail.
7 Click “Save Control Panel”.
![Page 11: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/11.jpg)
11
Programming
ADD DOORS/GATES
2 Click “Add Door”.
3 Enter Door Name. Select Control Panel
from drop-down.
4 Click “Next”.
5 Select Board from
drop-down. Select Node
from drop-down.
NOTES:
Board 1 Node 1 = Door 1
Board 1 Node 2 = Door 2
Navigate to Setup –> Sites and Doors. NOTE: If already on the “Site” page, click ”Add Door”1
![Page 12: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/12.jpg)
12
Programming
CONFIGURE A DOOR
2 Enter the door name.
3 Confi rm door settings.
4 Set a door unlock schedule if the
gate or door is held open or does
not require a credential to enter at
certain times. Note: Instructions for
how to a schedule can be found on
page 22.
The default values are appropriate
for most applications.
5 Select “Yes” for control from
browser (allows administrator to
open door through web).
6 Click “Save Door”.
Navigate to Setup –> Sites and Doors –> Edit Door. NOTE: If already creating a new door, the user will already be on
this page. Follow the steps below.1
![Page 13: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/13.jpg)
13
USB - Device
PE
RIP
HE
RA
LB
OA
RD
CO
NFIG
LA
N
US
B -
AD
MIN
REX 1
SENSE
COM
SHLDO NO
N1
2
3
4
IPPNL
MAC 00:00:00:00:00:00
CP# TEC–3K–YYYYL
CO
NFIG
O NO
N1
2
3
4
COM LINK -> A B
N.C.
COM
SHLD
N.O.
RELA
Y 1
N.C.
COM
SHLD
N.O.
AU
X 1
N.C.
COM
SHLD
N.O.
RELA
Y 2
N.C.
COM
SHLD
N.O.
AU
X 2
INP
UT 1
REX
2
INP
UT 2
SH
LD
CO
M
SEN
SE
SH
LD
CO
M
SEN
SE
SH
LD
CO
M
SEN
SE
GN
D
SH
IELD
LED
-GR
N
BU
Z
HO
LD
LED
-RED
D0
D1
12V
GN
D
SH
LD
LED
-GR
N
BU
Z
HO
LD
LED
-RED
D0
D1
12V
READER 1
CO
MM
LIN
K M
OD
ULE
RELAY BOARD
READER 2
Wiring
Unpack and mount IPAC using the provided knockouts.
If a Request to Exit (REX) switch is used,
wire it to REX 1 on the main board of the
unit. (Postal Lock switch)
Primary Relay
Auxiliary Relay Connected Monitor Input
WIRE DOOR #1
1
2
REX 1
3
4
Connect Wiegand input to Door #1 to trigger the Primary and Auxiliary relays.
Connect monitored input
for Door #1 (door monitor
switch).
RELAY BOARD
PERIPHERAL BOARD REX SWITCH
![Page 14: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/14.jpg)
14
COM LINK -> A B
N.C.
COM
SHLD
N.O.
RELA
Y 1
N.C.
COM
SHLD
N.O.
AU
X 1
N.C.
COM
SHLD
N.O.
RELA
Y 2
N.C.
COM
SHLD
N.O.
AU
X 2
INP
UT 1
REX
2
INP
UT 2
SH
LD
CO
M
SEN
SE
SH
LD
CO
M
SEN
SE
SH
LD
CO
M
SEN
SE
GN
D
SH
IELD
LED
-GR
N
BU
Z
HO
LD
LED
-RED
D0
D1
12V
GN
D
SH
LD
LED
-GR
N
BU
Z
HO
LD
LED
-RED
D0
D1
12V
READER 1
CO
MM
LIN
K M
OD
ULE
RELAY BOARD
READER 2
Connected Monitor Input
WIRE DOOR #2 (IF APPLICABLE)
Wiring
1
Primary Relay
Auxiliary Relay
If a Request to Exit (REX) switch is
used, wire it to REX 2.
2
3
Connect Wiegand input to Door #2 to trigger the Primary and Auxiliary relays.
Connect monitored input
for Door #2 (door monitor
switch).
REX 2
RELAY BOARD
REX SWITCH
![Page 15: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/15.jpg)
15
Navigate to Users –> Telephone Entry System –> New Telephone Directory.
Navigate to Setup –> Sites and Doors –> Site Directory.
Click on the desired site.
Programming
CREATE A DIRECTORY
CONFIGURE IPAC
1
1
2
3
2 Name the directory.
3 Set the directory code
length. The directory code
is a 4-6 digit code guests
use to dial a resident from
the IPAC. WARNING: The
code length cannot be
changed once residents
are added to the directory.4 Click “Save”.
Select “More
Operations”
and then “Add
IPAC Device”.
Programming
![Page 16: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/16.jpg)
16
Programming
CONFIGURE IPAC
4
5
Select IPAC Control Panel. Enter device
name.
Enter SIP Account Information.
Domain: SIP.Phone.com
SIP Username: (Example: 81976)
SIP Password: (Example: 8$Sh77y69dBm7v)
![Page 17: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/17.jpg)
17
Set other parameters:
Programming
CONFIGURE IPAC
6
7 Click “Save”.
Enter greeting message (appears at top of
IPAC screen).
GATE 1:
• Select DTMF key to grant access.
• Select Gate/Door to be controlled.
• Click Yes to enable access code entry from
IPAC panel.
GATE 2 (Optional):
• Select DTMF key to grant access.
• Select Gate/Door to be controlled.
• Click Yes to enable access code entry from
IPAC panel.
Edit Speaker and Mic Volume.
Select a Telephone Directory (the list of names
that will display on IPAC).
![Page 18: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/18.jpg)
18
Select “Site” pull-down menu
and select “All Sites” or the
desired site.
Assign a schedule to each door/gate this group can open. Leave
schedule blank if group has no rights to that door/gate. NOTE: See
“schedule” section in this manual for how to create a new schedule.
Programming
SET GROUP PRIVILEGES
Name Group and click “Save Group”.2
3
4
Navigate to Users –> New Group.1
Scroll to the bottom of the Site list to see the options to Save Group.5
![Page 19: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/19.jpg)
19
Navigate to Setup –> Cards –> Add Cards.
Programming
BULK LOAD CARDS/TRANSMITTERS
1
2 Select the format of the card/transmitter. NOTE: Different formats may display ad-
ditional settings.
3 Enter fi rst and
last Card Number.
Leave off leading
zeros. It is
recommended to
pick a standard
format for
all imported
credentials.
4 Enter Facility code.
5 Click “Add Cards”.
![Page 20: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/20.jpg)
20
Enter First Name, middle name, and last
name. Click “Save Identity”.
Assign PIN (Optional).
• Click “Credentials” Tab.
• Enter PIN or click 4, 5, 6, 7, or 8 to auto-assign PIN.
• Click “Save PIN” button.
To add a card, transmitter, or other credential, click “Choose” to open “Card Bank” and add credential to user.
• Select credential from “Add Cards” pop-up menu.
• Use fi lter or arrows to search for card.
• User can have multiple credentials.
• Click (X) to close “Add Cards” pop-up menu.
Programming
CREATE CREDENTIALED USER
For someone with a card, transmitter, PIN, or other credential:
2
3
4
Navigate to Users –> New User.1
![Page 21: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/21.jpg)
21
Set dates user will have access. Leave blank if permanent user.
Repeat as needed.
Select “Groups” tab.
• Click “Choose” button.
• Select group(s) from “Select Group” pop-up menu. NOTE: User can be in multiple groups.
• Click (X) to close “Add Cards” pop-up menu.
Programming
CREATE CREDENTIALED USER
5
6
7
![Page 22: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/22.jpg)
22
Navigate to Users –> Telephone Entry System –> New Resident.
Programming
CREATE A RESIDENT
A resident is someone with a phone number.
1
2
3
Select Directory.
Enter the resident’s name as it will
appear on IPAC.
4 Enter Directory Code (Or use
the buttons on the right to
auto-populate). The Directory Code
is the number a guest can use to
quickly call the associated resident
from IPAC.
5 Enter resident information. NOTE:
it is important to enter all 10 digits
of the resident’s phone number.
6 Set “Do Not Disturb Schedule”
(Optional). IPAC will not allow calls
to the resident during these times
and the guest is notifi ed.
7 If resident does not want to be search-able in directory, select “YES”.
8 Click “Save”.
![Page 23: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/23.jpg)
23
Navigate to Setup –> Schedules –> New Schedule.
Programming
CREATE A SCHEDULE
1
2
NOTE: Schedules have many uses when programming your IPAC and Door IPDC.
• Access times for groups assigned to each entrance. During the selected times, members of a group can present a card,
PIN, transmitter, or other credential to open the gate or door.
• Use to hold open a gate or leave a door unlocked. Select the times the gate or door should be open or unlocked.
• As a “do not call time” for residents. During the selected times guest cannot call the resident from IPAC.
3 Click and drag up or down to
block out the times which the
schedule will be ACTIVE.
Enter schedule name.
4 Click “Save Schedule”.
![Page 24: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/24.jpg)
24
Navigate to Setup –> Notifi cations –> New Notifi cation.
Programming
SET A NOTIFICATION
1
2
3
4
Select all sites the notifi cation rule will apply to .
Enter a description of the
notifi cation rule and enter the email
address to send the notifi cation.
Select the events to trigger
the notifi cation.
![Page 25: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/25.jpg)
25
Programming
If a notifi cation is tied to
a group or user, add the
group or user.
6 If desired, select
a schedule for the
notifi cation rule to
be active.
7 Click “Save Notifi cation”.
5
![Page 26: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/26.jpg)
26
Navigate to Setup –> Account –> Administrators.
Programming
CREATE A NEW SENIOR ADMINISTRATOR
1
2
3
Click “New”
next to “Senior
Administrators”.
Enter the administrator
information.
4 Determine whether this new
administrator can create other
administrators.
5 Enter the Administrator ID,
Password, Secret Qestion, and
Secret Answer.
6 Enter your password to confi rm
who is creating the new
administrator.
7 Click “Save Administrator”.
![Page 27: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/27.jpg)
27
Testing
2
3
4
5
Pick up the resident’s or called phone and press the desired number to trigger the door to open. The IPAC welcome
message will appear.
After the welcome message, confi rm the customizable message has appeared in the upper left of the IPAC display and
the clock is correct in the upper right of the IPAC display.
Confi rm all Wiegand inputs correctly trigger the relays and events appear in the Cloud software Activity Log. When
everything is working properly the IPAC is ready to be installed.
Install the IPAC. NOTE: Be sure all wiring is connected before applying power.
Press the directory button on the IPAC touch screen. The list of residents should appear. Press the desired name and
then press the “call” button. IPAC will show a “connecting” then a “calling” message and will ring.
AFTER COMPLETING THE SOFTWARE SETUP
Try to make a phone call from IPAC.
1
![Page 28: 0138241 IPAC Guide Wiring and Cloud Programming up and confi guring any IPACs and door ... Not responsible for conflicts between the information listed in the wiring diagram and ...](https://reader031.fdocuments.us/reader031/viewer/2022011723/5aa783357f8b9a294b8c3238/html5/thumbnails/28.jpg)
© 2015, LiftMasterAll Rights Reserved
LiftMaster
845 Larch Ave.
Elmhurst, IL 60126-1196
LiftMaster.com
01-38241