...2015 FIT APR 2014 PARTS LIST Left front door visor Right front door visor Left rear door visor...
7
Publications No. Issue Date INSTALLATION INSTRUCTIONS Accessory Application © 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 51183 (1404) 1 of 7 08R04-T5A-1000-90 AII 51183 DOOR VISORS P/N 08R04-T5A-100 2015 FIT APR 2014 PARTS LIST Left front door visor Right front door visor Left rear door visor Right rear door visor 6 Brackets A 2 Brackets B 8 Clips TOOLS AND SUPPLIES REQUIRED Isopropyl alcohol Shop towel Masking tape Ruler Soft towel INSTALLATION NOTE: • Visors may not be legal in all states. Please check the laws of your state. • These instructions show the left door visors being installed. The same procedure applies to installing the right door visors. • Be careful not to damage the body paint finish and glass run channels when installing the door visors. • Handle the door visors with care. They are not designed to absorb shock or impact. • This kit should be installed only if the ambient air temperature is 15°C (60°F) or above. • To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise your customer. Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” www.collegehillshonda.com
Transcript of ...2015 FIT APR 2014 PARTS LIST Left front door visor Right front door visor Left rear door visor...
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2014 American Honda Motor Co., Inc. – All Rights Re
AII 51183
www.collegehillshonda.com
DOOR VISORSP/N 08R04-T5A-100
served. AII 51183 (1404
2015 FIT
) 0
Issue Date
APR 2014
PARTS LIST
Left front door visor
Right front door visor
Left rear door visor
Right rear door visor
6 Brackets A
2 Brackets B
8 Clips
TOOLS AND SUPPLIES REQUIRED
Isopropyl alcohol
Shop towel
Masking tape
Ruler
Soft towel
INSTALLATION
NOTE:
• Visors may not be legal in all states. Please check the laws of your state.
• These instructions show the left door visors being installed. The same procedure applies to installing the right door visors.
• Be careful not to damage the body paint finish and glass run channels when installing the door visors.
• Handle the door visors with care. They are not designed to absorb shock or impact.
• This kit should be installed only if the ambient air temperature is 15°C (60°F) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise your customer.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1 of 78R04-T5A-1000-90
www.collegehillshonda.com
Installing the Front Door Visor1. Open the left front door glass.
2. Peel back the glass run channel in the areas shown.
3. Install the two brackets A between the door sash and the glass run channel at the measurements shown. Seat the glass run channel properly around the brackets.
QC31901AK
195 mm (7.7 in.)
GLASS RUN CHANNEL(Peel.)
195 mm(7.7 in.)
LEFT FRONT DOOR
BRACKET A
SECTION VIEW
DOOR SASH
GLASS RUNCHANNEL
2 BRACKETS A
EDGE OFDOOR SASH
EDGE OFDOOR SASH
BRACKET A
2 of 7 AII 51183
4. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the left front door visor will attach.
5. Peel back the adhesive backings from each adhesive tape, and tape the ends to the front surface of the left front door visor with masking tape.
QC82801AK
Clean with isopropyl alcohol.
SHOP TOWEL
LEFT FRONT DOOR
QC31903AK
MASKING TAPE
3 ADHESIVE BACKINGS(Peel back and tape them to the front surface of the left front door visor.)
LEFT FRONT DOOR VISOR
(1404) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
6. Align the clip holes in the left front door visor with thebracket holes, and install the clip while pushing up on each bracket A. There should be no clearance between the brackets and the door sash.NOTE: Be extremely careful when installing the clips, they cannot be reinstalled after installation.
QC31904AK
LEFT FRONTDOOR VISOR(inside)
Pushup.
LEFT FRONT DOOR
2 CLIPS
GLASS RUNCHANNEL
BRACKET A
CLIP
SECTION VIEW BRACKET A
PROJECTION
LEFT FRONTDOOR VISOR
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 51183
7. Adjust the left front door visor to the position as shown.
QC92001AK
BACK VIEW
Align the door visor with the door sash.
DOORSASH
2 mm(0.1 in.)
EDGE OFDOORSASH
FRONT VIEW
LEFT FRONT DOOR
Align the door visor with the door sash.
DOORSASH
(1404) 3 of 7
www.collegehillshonda.com
8. While applying light pressure against the left frontdoor visor, carefully remove the adhesive backings in the order shown. Use your finger to push up each bracket so there is no gap between the bracket and the door sash.
9. Using a soft towel, press and hold the left front door visor against the door sash for 30 seconds.
QC31906AK
Pushup.
GLASS RUNCHANNEL
BRACKET A
3 ADHESIVE BACKINGS(Remove.)
1
2
SECTIONVIEW
3
LEFT FRONT DOOR
4 of 7 AII 51183
Installing the Rear Door Visor
10. Fully open the left rear door glass.
11. Peel back the glass run channel in the areas shown.
12. Install the brackets A and B between the door sash and the glass run channel at the measurements shown. Seat the glass run channel properly around the brackets.
QC31907BK
GLASS RUNCHANNEL(Peel.)
BRACKET A SECTION VIEW
BRACKET B
DOOR SASH
BRACKET A
GLASS RUNCHANNEL
BRACKET B
BRACKET A
170 mm (6.7 in.)
EDGE OFDOOR SASH
195 mm (7.7 in.)
LEFT REARDOOR
SECTION VIEW
DOOR SASH
EDGE OFDOOR SASH
(1404) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
13. Using isopropyl alcohol on a shop towel, thoroughlyclean the area where the left rear door visor will attach.
14. Peel back the adhesive backings from each adhesive tape, and tape the ends to the front surface of the left rear door visor with masking tape.
QC82802AK
Clean with isopropyl alcohol.
SHOP TOWEL
LEFT REAR DOOR
QC31909AK
MASKING TAPE
3 ADHESIVE BACKINGS(Peel back and tape them to the front surface of the left rear door visor.)
LEFT REAR DOOR VISOR
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 51183
15. Align the clip holes in the left rear door visor with the bracket holes, and install the clip while pushing up on each bracket A/B. There should be no clearance between the brackets and the door sash.NOTE: Be extremely careful when installing the clips, they cannot be reinstalled after installation.
QC31910AK
LEFT REAR DOOR VISOR(inside)
Pushup.
LEFT REAR DOOR
2 CLIPS
GLASS RUN CHANNEL
BRACKET A
SECTION VIEW
PROJECTION
BRACKET B
PROJECTIO
BRACKET A
CLIP
SECTIONVIEW
CLIP
LEFT REARDOOR VISOR
LEFT REAR DOOR VISOR(inside)
Pushup.
(1404) 5 of 7
www.collegehillshonda.com
16. Adjust the left rear door visor to the position asshown.
QC92002AK
2 mm(0.1 in.)
EDGE OFDOOR SASH
Align the door visor with the door sash.
DOOR SASH
FRONT VIEW
LEFT REAR DOOR
6 of 7 AII 51183
17. While applying light pressure against the left rear door visor, carefully remove the adhesive backings in the order shown. Use your finger to push up each bracket so there is no gap between the bracket and the door sash.
18. Using a soft towel, press and hold the left rear door visor against the door sash for 30 seconds.
19. Repeat steps 1 through 18 to install the right front and rear door visors on the right side of the vehicle.
QC31912AK
GLASS RUNCHANNEL BRACKET A
3 ADHESIVE BACKINGS(Remove.)
1
2
SECTIONVIEW
3
SECTION VIEWBRACKET B
GLASS RUNCHANNEL
LEFT REAR DOOR
Pushup. Push
up.
(1404) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
CONFIRMATION AFTER INSTALLATIONRestoration and Learning Operations
1. Start the engine.
2. Using the power window switch, repeat opening and close the window from half-open to fully closed 10 times to allow the glass run channel to wear in. (The window should not bind.)
3. If necessary refer to the Service Manual to reset the power window. (If the automatic closing/opening does not function after the reset, reset again.)
4. If necessary refer to the Service Manual to carry out “learning” of the power window. (If the automatic closing/opening does not function after the learning, carry out “learning” again.)NOTE: The operations in the steps 3 and 4 should be done to all power windows having the automatic closing/opening function to allow for proper functioning of the auto-reverse function after installing the door visors.
USE AND CARE
Clean the door visors with mild detergent and water. Do not use organic solvents (thinners, benzine, alcohol, etc.) or cleaners containing any abrasive material.
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 51183
(1404) 7 of 7
